SA520W - how to enable communication between LAN Devices?

We install our new SA520W Security Appliance. Wireless is setup and Internet works fine.
But we want to PING another computer inside the LAN it does not response. We can not see other computers, printers or devices even they are in the same network, same IP range by wire or wireless. Is there something we need to enable in Utilities?
We have shared folders and printers on the network, so we had to come back to our old router. Please help.
Thanks,
AJ

By default the SA520w isolates wifi clients from each other. The setting you are looking for is AP isolation under APN settings. this needs to be switched off
For more details see page 108 in the manual
hope this helps
Julian

Similar Messages

How to enable Wake On Lan on MSi P45 Neo2?

Hi,
I just bought a P45 Neo2, and I think I have WOL on this machine, as the Realtek chipset 8111C does support the feature. However, I'm not sure how to
- enable
- use
the function. Can you help me?
Under Device Manager, I go to the Realtek network adapter --> Properties --> Power Management --> Allow this device to bring the computer out of standby.
Now, it is enabled. How should I use it? I would be very thankful :-).

Please have a look here first for basic introduction to Wake on LAN and "Magic Packets":
http://en.wikipedia.org/wiki/Wake-on-LAN#How_it_works

How to enable wake on lan on Thinkpad Twist?

I have a Thinkpad Twist purchased because of the presence of the ethernet card.
Unfortunately I can not turn wake on lan.
I did several searches and several attempts without success.
Someone managed to enable wake on lan?
Thank you.
(sorry for the English by Google Translate)
Solved!
Go to Solution.

Hey there Cello67,
To enable Wake On Lan on a Thinkpad twist:
1) You will first need to power down your laptop completely.
2) Then turn it on, as soon as you turn it on start hitting the enter key to interrupt start up. This will take you to a start up menu.
3) From here you will need to enter your BIOS.
4) Move right over to the Config, then press enter on the Network Selection
5) The first option you should have is Wake On Lan. You can change this from disabled to either AC Only or AC and Battery.
After you have done this save your settings, and resume startup. Once the computer has finished booting go to your desktop, and pull out your charm bar by pressing Win Key + C or with a swipe from the right side of your screen in. From here you will:
1) Enter the Control Panel
2) Device Manager - > Your Ethernet Card/Adapter
3) Click the Power Management Tab
4) Select "Allow this device to wake the computer"
Hope this helps Cello67!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

GPIB Communication between multiple devices

Hello,
I am trying to build an application in C# which will be able to send commands to more than one device on the GPIB BUS.
For example I have 3 devices connected to the computer with addresses as:"GPIB0::18::INSTR","GPIB0::19::INSTR","GPIB0::28::INSTR"
Now, I know how to communicate with a single device.
But is there a way I can send commands to multiple devices. So far I have the following.
using System;
using System.Collections.Generic;
using System.ComponentModel;
using System.Data;
using System.Drawing;
using System.Linq;
using System.Text;
using System.Windows.Forms;
using Ivi.Visa.Interop;
namespace Step_Attenuator
public partial class Form1 : Form
ResourceManager rMgr = new ResourceManager();
Ivi.Visa.Interop.FormattedIO488 ioobj = new FormattedIO488();
object resources = null;
string address1 = "GPIB0::18::INSTR";
string address2 = "GPIB0::19::INSTR";
string address3 = "GPIB0::28::INSTR";
public Form1()
InitializeComponent();
private void PsaComm()
private void Form1_Load(object sender, EventArgs e)
private void button1_Click(object sender, EventArgs e)
ioobj.IO = (IMessage)rMgr.Open(address1);
ioobj.WriteString("*RST");
But now If I want to send a RST command to say device on address2, do I have to again open the session and send it?
There are going to be a lot of commands to these devices. I am sure there is a much simpler way to do it.
Please pardon me if this seems to be a silly question.
Thank You.

Hi nmedelec,
I made a research about “Ivi.Visa.Interop.FormattedIO488” and it seems that it is related with Ivi.Visa.Interop which is a third party product. If you have any issue about a third party, I would recommend you go to the office site for help.
Thanks for your understanding.
Best Regards,
Edward
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click HERE to participate the survey.

How to transfer imovie between ios devices

how do I to transfer imovies between ios devices?

That's a standard part of the synchronization activity.
Please read.
There have been some problems accessing pages on the Apple web site. If the hyperlink gives you a "We're sorry" message, try again.

How to enable SSO between two peoplesoft Instances

Hi,
How can we enable SSO between 2 Peoplesoft Instances.
Instance no1 has 2 webs on seperate servers and db on seperate server
Instance no 2 has web/app on one server and only DB on seperate server
Thanks

Hi,
First make sure the webservers and application servers can communicate with each other by open firewall rules, if not done yet.
Set the default local nodes to user authenticate and make sure the node are pingable from the other environment.
After this set the remote nodes to be trusted and SSO of PeopleSoft is done.
Read more in detail in PeopleBooks.
PeopleBooks > PeopleTools 8.52: Security Administration > Implementing Single Signon > Implementing PeopleSoft-Only Single Signon
http://docs.oracle.com/cd/E28394_01/pt852pbh1/eng/psbooks/tsec/book.htm?File=tsec/htm/tsec10.htm#H3005

How to Enable TLS between two domain

Hi All,
our partner want us to enable TLS in Email. how to enable in my environment also this TLS should be for specific partner not for all. if so what all the information required from their side i suppose to ask. Please guide be in a basic manner.
we are using Exchange 2010.
Thanks, Venkatesh. "Hardwork Never Fails"

HI Venkatesh,
Please check this article it is for 2007 but you can test do the change as per 2010.
http://www.msexchange.org/articles-tutorials/exchange-server-2007/security-message-hygiene/Securing-SMTP-Message-Flow-between-different-Exchange-Server-2007-organizations.html
Also, check this
http://dizdarevic.ba/ddamirblog/?p=78

HT203521 How to sync calender between mulitple devices

How to sync calender between mulitple devicesHow to sync calender between mulitple devices

Howdy gvromano,
The article linked below details how to go about setting up iCloud on your computers and devices.
iCloud: Set up iCloud
https://support.apple.com/kb/PH2609
Sincerely,
Allen

How do you tweet between apple devices

My daughter says there's a separate tweet thing which lets you tweet free between apple devices.
I can't find it

It sound like you are refering to "iMessage," which is a iOS exclusive messaging service: http://support.apple.com/kb/HT3529

Sa520w communications between LAN and DMZ extremely slow

Hello,
I'm new to cisco products and I just bought a sa520w. I'm upgraded to the latest firmware (1.1.65). I set up a ipv4 rule that allows all communications from the LAN to the DMZ (see below from the backup). It works (e.g. all the protocols I use can communicate), but they are all _very_ slow. Secure protocols (i.e. scp) cannot be used because they are just too slow. I'm upgraded to the latest firmware (1.1.65). Does anyone have any experience with this?
Thanks,
Ryan
FirewallRules[2] = {}
FirewallRules[2]["PriorityId"] = "97"
FirewallRules[2]["Action"] = "ACCEPT"
FirewallRules[2]["_ROWID_"] = "97"
FirewallRules[2]["LogLevel"] = "1"
FirewallRules[2]["FromZoneType"] = "SECURE"
FirewallRules[2]["ServiceName"] = "ANY"
FirewallRules[2]["RuleType"] = "SECURE_INSECURE"
FirewallRules[2]["InsertFrmGui"] = "0"
FirewallRules[2]["TypeOfService"] = "0"
FirewallRules[2]["SourceAddressType"] = "0"
FirewallRules[2]["DestinationAddressType"] = "0"
FirewallRules[2]["Status"] = "1"
FirewallRules[2]["SNATAddressType"] = "7"
FirewallRules[2]["ToZoneType"] = "INSECURE"
FirewallRules[2]["DNATPortEnable"] = "0"

Hi Ryan,
Is the slowdown seen on wired LAN users or wireless LAN users or both? If possible, can you provide us the configuration and dbglogs from your SA 520W so that I can forward to the development team to try to reproduce and investigate?
To get the dbglog from SA520W, login through web UI and in the browser enter the following URL:
https://LAN_IP_address_of_SA520W/scgi-bin/dbglog.cgi
These logs will store password, so please remove any sensitive information and passwords. Also if you are not comfortable posting the dbglog on the community, you can send it directly to me through private message.
Best regards,
Julio

How to Enable Wake On Lan over the Internet??

Hi, I am using RV220W with the latest firmware, I want to make "Wake on LAN" work for my NAS, I found the following description on Internet:
"If you wish to use Wake On Lan over the internet you will need to set up your destination firewall/router to allow "Subnet Directed Broadcasts". Most routers and firewalls disable this option by default.
You will then need to allow traffic through on your firewall/router on a specific port. The choice of ports is up to you."
So how can I enable "Subnet Directed Broadcasts" on RV220W??
Thanks.
Raymond

Hi Jasbryan,
If RV220W doesn't forward UDP to a broadcast address, could you ( i.e. Cisco) provide a tools for sending WOL Magic Packet to the LAN on Router Device Manager page?
I see many routers also provide this tools from their manager page.
Thanks.
Raymond

How to establish communication between dynpro and Applet running in Portal

Hello SDN,
I have a problem with concept of my app and would be glad if You can help me.
- I needed a graphics engine to draw a map during a dynpro runtime, and i made applet for it because dynpro don't offer suitable api.
Map have to show some data from Bussines Warehouse and R/3 and also have to return coordinates onMouse click to dynpro app.
My question is how to pass params from web dynpro app to applet and receive coordinates after mouse click on map.
I made dynpage and placed my applet inside for EPCF but don't know how to use it in applet?

1. First of all set up the Rfc connection between System A and System B.
If you are calling the function module which is avlaible on Syetem A and calling in system B. In system A, go to SM59 opt for R\3 connection and give all the details in "Technical settings" and "logon & Security" tabs and test your connection. If you are returning any value Back to system A , make the same settings in system B.
2. While creating the Function module check the Radio-button "Remote-Enabled Module" in the attributes tab.
3. Call function <function-name> Destination <Destination-name>.

How to Establish communication between two R/3 systems.

Hi experts,
I have a requirement in which I have a group of programs on a R/3 system A.Now, I need to execute those programs on another R/3 system B.
For example,
I have developed a program which performs syntax check on all the existing programs in the sysytem A.
This program is developed on system A. but my requirement is that I should execute this program on system B and find all the syntactically incorrect programs on system B.
How do I achieve this
Please provide solutions.

1. First of all set up the Rfc connection between System A and System B.
If you are calling the function module which is avlaible on Syetem A and calling in system B. In system A, go to SM59 opt for R\3 connection and give all the details in "Technical settings" and "logon & Security" tabs and test your connection. If you are returning any value Back to system A , make the same settings in system B.
2. While creating the Function module check the Radio-button "Remote-Enabled Module" in the attributes tab.
3. Call function <function-name> Destination <Destination-name>.

How to enable routing between HWIC-4ESW and Onboard FE on cisco 1841 router..?

Hello All,
I have a cisco 1841 router, recently i have purchased HWIC-4ESW slot for my router. The module is working fine i could able to see additional FE ports(fe0/0/0,fe0/0/1...).Now problem comes in routing i.e. these HWIC-4ESW ports and Onboard FEs are not communicating.If any bode knows the solution kindly let me know the configuration details..
Thanks,Sazz

Hi,
Look at the configs below.
How can I use IP Routing so communication is possible across all subnets?
Router>en
Router#config t
Router(config)#int fa0/0
Router(config-if)#description ***INTERNET***
Router(config-if)#ip address xxx.xxx.xxx.xxx 255.255.255.252
Router(config-if)#no shut
Router(config-if)#ip nat outside
Router(config-if)#exit
!On-board interface
Router(config)#int fa0/1
Router(config-if)#description ***LAN***
Router(config-if)#ip address 10.0.xxx.xxx 255.255.255.0
Router(config-if)#no shut
Router(config-if)#ip nat inside
Router(config-if)#exit
Router#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Router(vlan)#vlan 10
VLAN 10 modified:
Router(vlan)#vlan 20
VLAN 20 added:
Name: VLAN0020
Router(vlan)#exit
APPLY completed.
Exiting....
Router#config t
Router(config)#int vlan 10
Router(config-if)#ip address 172.16.xxx.xxx 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int vlan 20
Router(config-if)#ip address 192.168.xxx.xxx 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#no shut
Router(config-if)#exit
!HwIC-4ESW interface
Router(config)#int fa0/0/0
Router(config-if)#switchport mode access
Router(config-if)#switchport access vlan 10
Router(config-if)#exit
!HWIC-4ESW Interface
Router(config)#int fa0/0/1
Router(config-if)#switchport mode access
Router(config-if)#switchport access vlan 20
Router(config-if)#exit
Router(config)#exit
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#config t
Router(config)#ip name-server xxx.xxx.xxx.xxx
Router(config)#ip name-server xxx.xxx.xxx.xxx
Router(config)#exit
Regards,

Communication between connected devices

Can anyone confirm that two connected devices (e.g., a laptop and a desktop) can exchange files through the Verizon 4G LTE Router? Or are they limited to individually connecting to the internet as with jetpacks?

There should be no reason why two LAN connected computers could not share files between each other on the 4G LTE router. If you experience any problems it is because the sharing of the two devices is not setup correctly. A side note, local file sharing does not count against your VZW data plan. Only traffic that goes across VZW's network is metered and held against you.
You can share files between two local devices on a Jetpack without any extra configuration. Its the sharing between a local and remote device that does not work out of the box. Even then you can work around the limitations with a proper VPN environment.
Let us know if you recieve a specific error message when you try to share along with the OS of each computer. I'm sure we can walk you through the process.

SA520W - how to enable communication between LAN Devices?

Similar Messages

Maybe you are looking for