Safari hangs after Yosemite install;

I installed Yosemite on my MAC Book Pro;
When my Mac is in sleep mode and the cover is closed, Safari hangs and I get a blank screen;
The only fix I found was to restart the Mac and safari is back.
any recommendations on how to fix the safari issue?

thanks for the reply;
I can quit safari fine; no need to force quit; I get a white screen and nothing happens.
I can quit safari normally;
I restart it and get the same white screen
However when I restart my Mac , safari works fine.
This process happens every morning; I close the cover to my Mac at night, and try to start it the following day.

Similar Messages

Safari hangs after Yosemite update

Updated to 10.10.3 Safari now hangs, won't open any webpages. I did clear history and cookies and restarted Safari. No luck. Firefox running with no issues.
Safari is the default browser.. (but that will be changing shortly)

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a general summary of what you need to do, if you choose to proceed:
☞ Copy a particular line of text to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
These are not specific instructions; just an overview. The details are in parts 7 and 8 of this comment. The sequence is: copy, paste, wait, paste again. You don't need to copy a second time.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. Load this linked web page (on the website "Pastebin.") The title of the page is "Diagnostic Test." Below the title is a text box headed by three small icons. The one on the right represents a clipboard. Click that icon to select the text, then copy it to the Clipboard on your computer by pressing the key combination command-C.
If the text doesn't highlight when you click the icon, select it by triple-clicking anywhere inside the box. Don't select the whole page, just the text in the box.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window to activate it. Paste from the Clipboard into the window by pressing command-V, then press return. The text you pasted should vanish immediately.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "The message contains invalid characters." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but whatever else you're told to do may not be. For others who choose to run it, I don't recommend that you post the test results on this website unless I asked you to.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work (including the referenced "Diagnostic Test"), I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Unable to bootup after Yosemite install. have to keep shutting down from rear button. it does come on after a few times but then hangs at user login again. If you get in it is great. Seems faster than Mavericks but there is some sort of issue, bouts

unable to bootup after Yosemite install. have to keep shutting down from rear button. it does come on after a few times but then hangs at user login again. If you get in it is great. Seems faster than Mavericks but there is some sort of issue, bootup /login.

Knock on wood, this seems to have been my problem as well. I stumbled on this thread after dealing with this ridiculously-long boot times for the past several weeks.
I just reinstalled McAfee Antivirus and my Macbook Air booted up in less than 1 minute. No more hanging on the boot-up progress bar. No more hanging after I click on my user's avatar on the log-in screen. Bootup would often take 5+ minutes and sometimes never complete.
This has been SUPREMELY frustrating.
THANK YOU SO MUCH FOR POSTING YOUR RESPONSE!!!

Keeps crashing after Yosemite install - Need thoughts on what to do...

My 2013 Macbook Air keeps crashing after Yosemite install, time between crashes are more random than consistent and it can be anytginh from one hour to 6 hours between crashes. Enclosed the report below with the hope that someone has some tips on what to do here.... I've formatted the computer, reinstalled the OS and checked the drive for errors and I've found nothing so far.
Would be very grateful for any thoughts/tips on what to do here...
Anonymous UUID:       BEEFE0EB-6E39-4774-2F21-C8DB361123F7
Tue Oct 21 23:43:49 2014
*** Panic Report ***
panic(cpu 0 caller 0xffffff8007d7a590): "a freed zone element has been modified in zone kalloc.1024: expected 0xdb989f771eb1bbd8 but found 0x60002, bits changed 0xdb989f771eb7bbda, at offset 0 of 1024 in element 0xffffff8018915c00, cookies 0x3f0011f6db804ed8 0x5352198c01c0537"@/SourceCache/xnu/xnu-2782.1.97/osfmk/kern/zalloc.c:496
Backtrace (CPU 0), Frame : Return Address
0xffffff81102c32d0 : 0xffffff8007d3a811
0xffffff81102c3350 : 0xffffff8007d7a590
0xffffff81102c33c0 : 0xffffff8007d79c17
0xffffff81102c3400 : 0xffffff8007d78de7
0xffffff81102c3530 : 0xffffff800813160e
0xffffff81102c36d0 : 0xffffff800812aab9
0xffffff81102c3760 : 0xffffff8008140ccf
0xffffff81102c3930 : 0xffffff8007f3f2f8
0xffffff81102c3a10 : 0xffffff8007f3ea95
0xffffff81102c3b40 : 0xffffff8007f52005
0xffffff81102c3b90 : 0xffffff8007f62505
0xffffff81102c3d90 : 0xffffff8007f56d87
0xffffff81102c3f50 : 0xffffff800824dcb2
0xffffff81102c3fb0 : 0xffffff8007e3ac46
BSD process name corresponding to current thread: PhotoStreamAgent
Mac OS version:
14A389
Kernel version:
Darwin Kernel Version 14.0.0: Fri Sep 19 00:26:44 PDT 2014; root:xnu-2782.1.97~2/RELEASE_X86_64
Kernel UUID: 89E10306-BC78-3A3B-955C-7C4922577E61
Kernel slide:     0x0000000007a00000
Kernel text base: 0xffffff8007c00000
__HIB text base: 0xffffff8007b00000
System model name: MacBookAir6,1 (Mac-35C1E88140C3E6CF)
System uptime in nanoseconds: 16215962667183
last loaded kext at 9812882932706: com.apple.filesystems.smbfs 3.0.0 (addr 0xffffff7f8a0e1000, size 389120)
last unloaded kext at 1736098368348: com.apple.driver.AppleUSBCDC 4.2.2b5 (addr 0xffffff7f895e6000, size 16384)
loaded kexts:
com.apple.filesystems.smbfs 3.0.0
com.apple.driver.AppleBluetoothMultitouch 85.3
com.apple.iokit.SCSITaskUserClient 3.7.0
com.apple.iokit.IOBluetoothSerialManager 4.3.0f10
com.apple.driver.AudioAUUC 1.70
com.apple.iokit.IOUserEthernet 1.0.1
com.apple.driver.AppleUpstreamUserClient 3.6.1
com.apple.driver.AGPM 100.14.37
com.apple.driver.ApplePlatformEnabler 2.1.0d1
com.apple.driver.X86PlatformShim 1.0.0
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleIntelHD5000Graphics 10.0.0
com.apple.driver.AppleHDA 266.5
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleOSXWatchdog 1
com.apple.driver.AppleLPC 1.7.3
com.apple.driver.AppleThunderboltIP 2.0.2
com.apple.driver.AppleBacklight 170.4.12
com.apple.driver.AppleUSBEthernet 2.4.7
com.apple.driver.AppleHV 1
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.3.0f10
com.apple.driver.AppleSMCLMU 2.0.4d1
com.apple.driver.AirPort.Brcm4360 900.19.8
com.apple.driver.AppleCameraInterface 5.23.0
com.apple.driver.AppleMCCSControl 1.2.10
com.apple.driver.AppleIntelFramebufferAzul 10.0.0
com.apple.filesystems.autofs 3.0
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.driver.AppleUSBHub 705.4.1
com.apple.driver.AppleTopCaseHIDEventDriver 46.2
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.6.5
com.apple.driver.AppleAHCIPort 3.0.7
com.apple.driver.AppleUSBXHCI 705.4.14
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleACPIButtons 3.1
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 2.1
com.apple.driver.AppleACPIEC 3.1
com.apple.driver.AppleAPIC 1.7
com.apple.nke.applicationfirewall 161
com.apple.security.quarantine 3
com.apple.security.TMSafetyNet 8
com.apple.driver.IOBluetoothHIDDriver 4.3.0f10
com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.0
com.apple.iokit.IOUSBMassStorageClass 3.7.0
com.apple.iokit.IOSurface 97
com.apple.driver.DspFuncLib 266.5
com.apple.kext.OSvKernDSPLib 1.15
com.apple.iokit.IOAudioFamily 200.6
com.apple.vecLib.kext 1.2.0
com.apple.driver.AppleBacklightExpert 1.1.0
com.apple.iokit.IONDRVSupport 2.4.1
com.apple.driver.AppleHDAController 266.5
com.apple.iokit.IOHDAFamily 266.5
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.3.0f10
com.apple.iokit.IOBluetoothFamily 4.3.0f10
com.apple.iokit.IO80211Family 700.52
com.apple.driver.mDNSOffloadUserClient 1.0.1b8
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOSerialFamily 11
com.apple.driver.X86PlatformPlugin 1.0.0
com.apple.driver.AppleSMC 3.1.9
com.apple.driver.IOPlatformPluginFamily 5.8.0d49
com.apple.driver.AppleSMBusController 1.0.13d1
com.apple.AppleGraphicsDeviceControl 3.7.21
com.apple.iokit.IOAcceleratorFamily2 156.4
com.apple.iokit.IOGraphicsFamily 2.4.1
com.apple.kext.triggers 1.0
com.apple.iokit.IOUSBUserClient 705.4.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.0
com.apple.driver.AppleUSBMergeNub 705.4.0
com.apple.driver.AppleUSBComposite 705.4.9
com.apple.driver.CoreStorage 471
com.apple.driver.AppleHIDKeyboard 175.5
com.apple.driver.AppleHSSPIHIDDriver 26.2
com.apple.driver.AppleMultitouchDriver 260.30
com.apple.iokit.IOAHCIFamily 2.7.0
com.apple.driver.AppleThunderboltDPInAdapter 4.0.6
com.apple.driver.AppleThunderboltDPAdapterFamily 4.0.6
com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2
com.apple.driver.AppleThunderboltNHI 3.1.7
com.apple.iokit.IOThunderboltFamily 4.2.1
com.apple.driver.AppleHSSPISupport 26.2
com.apple.driver.AppleIntelLpssSpiController 2.0.45
com.apple.driver.AppleIntelLpssDmac 2.0.45
com.apple.driver.AppleIntelLpssGspi 2.0.45
com.apple.iokit.IOUSBFamily 705.4.14
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 300.0
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.AppleKeyStore 2
com.apple.driver.AppleMobileFileIntegrity 1.0.5
com.apple.driver.AppleCredentialManager 1.0
com.apple.driver.DiskImages 389.1
com.apple.iokit.IOStorageFamily 2.0
com.apple.iokit.IOReportFamily 31
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 3.1
com.apple.iokit.IOPCIFamily 2.9
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.Libm 1
com.apple.kec.corecrypto 1.0
com.apple.kec.pthread 1
Model: MacBookAir6,1, BootROM MBA61.0099.B16, 2 processors, Intel Core i7, 1.7 GHz, 8 GB, SMC 2.12f143
Graphics: Intel HD Graphics 5000, Intel HD Graphics 5000, Built-In
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1600 MHz, 0x80AD, 0x483943434E4E4E384A544D4C41522D4E544D
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1600 MHz, 0x80AD, 0x483943434E4E4E384A544D4C41522D4E544D
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x117), Broadcom BCM43xx 1.0 (7.15.124.12.8)
Bluetooth: Version 4.3.0f10 14890, 3 services, 27 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en0
Serial ATA Device: APPLE SSD SM0512F, 500,28 GB
USB Device: My Passport 0824
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
Thunderbolt Bus: MacBook Air, Apple Inc., 23.6

Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu.
Reinstall Lion, Mountain Lion, or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
     Note: You will need an active Internet connection. I suggest using Ethernet
                 if possible because it is three times faster than wireless.

Messages stuck in updating after Yosemite install

Messages stuck in updating after Yosemite install. Tried re-install of Yosemite and quit messages, still unable to access.

Hi,
Go to the ~/Library/Attachments folder. (well it should be a folder).
If it is not a Folder then rename it and create a New folder with the same name.
restart Messages.
Or if you have a Time Machine backup replace the Non folder item with an Original from just before the update.
9:22 pm Saturday; January 17, 2015
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

My MacBook Pro's internal SuperDrive has stopped recognizing CDs/DVDs after Yosemite install

After upgrading to Yosemite, my MacBook Pro's (early 2011) internal SuperDrive has stopped recognizing CDs/DVDs after Yosemite install. It takes them in and will eject them with the keyboard button, but they will not mount. Disk Utility shows the SuperDrive and shows the inserted media, but will not mount the disk. That button is grayed out. Please help! I still have training libraries and music I access on such media. Thx!

UPDATE: I discovered some forum posts about a similar issue with Mavericks that recommended re-installing the system to fix the problem. I realized that I rarely restart my computer unless there's an update that requires it, and decided before undertaking a full re-install of Yosemite to simply restart my computer again. THIS WORKED! The SuperDrive is now mounting CDs and DVDs. Not sure what the issue was, but if anyone else has this issue I hope this will save you hours of frustration.

Safari Hangs after deleting :Awesome" but works for few when restrating

Safari Hangs after deleting"Awesome" but works for few minutes once shutdown and restart

I tried to look at other similar problems and tried to play around with it.
What I noticed was that I deleted the application but did not uninstall the extension.
Now I have now uninstalled the extension and Safari is back to normal.
Thanks Andy for your response

My computer is running slow after Yosemite install -but in the Mail program, when I open an email and then open the attachment -all is good -when I close the attachment the Mail program goes away, and I have to reopen it in my Dock -every time -been

My computer is running slow after Yosemite install -but in the Mail program, when I open an email and then open the attachment -all is good -when I close the attachment the Mail program goes away, and I have to reopen it in my Dock -every time.

I tried this, but no luck. I went to Previous System>Users. There is nothing inside the "Users" folder, so I hit a dead end.
I can find my new e-mails -- those that came in since I re-installed the system -- in my NEW system (which I did to see if I was correctly understanding the advice), by going to Users>Home>Library>Mail>POP account name>Inbox.
Let me add a new question: I am running PhotoShop C3. It opens OK, and I can use it, but when it opens I get this message: "One or more files for Adobe Application Support folder are missing. Please re-run the PhotoShop installer."
I don't like re-installing working programs if I can avoid it, because it always seems to lead to other issues. Any idea what files are missing, and where it/they might be in the Previous System folder?
thanks
Mike

My display is non hdcp compliant after Yosemite install

My display is non hdcp compliant after Yosemite install, fix this?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Very long shutdown time after Yosemite install

After installing Yosemite my Macbookpro has shutdown times of over more than 5 minutes. This is what i got from Etrecheck.
Problem description:
very long shutdown time after yosemite install
EtreCheck version: 2.1.8 (121)
Report generated 19 Feb 2015 01:19:39 CET
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
    MacBook Pro (15-inch, Early 2011) (Technical Specifications)
    MacBook Pro - model: MacBookPro8,2
    1 2 GHz Intel Core i7 CPU: 4-core
    8 GB RAM Upgradeable
        BANK 0/DIMM0
            4 GB DDR3 1333 MHz ok
        BANK 1/DIMM0
            4 GB DDR3 1333 MHz ok
    Bluetooth: Old - Handoff/Airdrop2 not supported
    Wireless: en1: 802.11 a/b/g/n
    Battery Health: Normal - Cycle count 868
Video Information: ℹ️
    Intel HD Graphics 3000 - VRAM: 512 MB
    AMD Radeon HD 6490M - VRAM: 256 MB
        Color LCD 1440 x 900
System Software: ℹ️
    OS X 10.10.2 (14C109) - Time since boot: one day 7:40:33
Disk Information: ℹ️
    Hitachi HTS545050B9A302 disk0 : (500,11 GB)
        EFI (disk0s1) <not mounted> : 210 MB
        Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
        Macintosh HD (disk1) / : 498.88 GB (90.86 GB free)
            Core Storage: disk0s2 499.25 GB Online
    MATSHITADVD-R   UJ-898
USB Information: ℹ️
    Apple Computer, Inc. IR Receiver
    Apple Inc. FaceTime HD Camera (Built-in)
    LaCie LaCie Device 500,11 GB
        EFI (disk2s1) <not mounted> : 210 MB
        MINI DAVID HDD (disk2s2) /Volumes/MINI DAVID HDD : 499.76 GB (62.48 GB free)
    Apple Inc. BRCM2070 Hub
        Apple Inc. Bluetooth USB Host Controller
    Apple Inc. Apple Internal Keyboard / Trackpad
Thunderbolt Information: ℹ️
    Apple Inc. thunderbolt_bus
Configuration files: ℹ️
    /etc/sysctl.conf - Exists
Gatekeeper: ℹ️
    Mac App Store and identified developers
Kernel Extensions: ℹ️
        /Applications/Karabiner.app
    [not loaded]    org.pqrs.driver.Karabiner (10.2.0 - SDK 10.9) [Click for support]
        /Library/Parallels/Parallels Service.app
    [not loaded]    com.parallels.kext.prl_hid_hook (7.0 15106.786747) [Click for support]
    [not loaded]    com.parallels.kext.prl_hypervisor (7.0 15106.786747) [Click for support]
    [not loaded]    com.parallels.kext.prl_netbridge (7.0 15106.786747) [Click for support]
    [not loaded]    com.parallels.kext.prl_usb_connect (7.0 15106.786747) [Click for support]
    [not loaded]    com.parallels.kext.prl_vnic (7.0 15106.786747) [Click for support]
        /System/Library/Extensions
    [not loaded]    com.Avid.driver.AvidDX (4.7.1) [Click for support]
    [loaded]    com.Cycling74.driver.Soundflower (1.5.1) [Click for support]
    [not loaded]    com.SafeNet.driver.Sentinel (7.3.0) [Click for support]
    [not loaded]    com.avid.driver.Avid_SCSI (1.2.0) [Click for support]
    [not loaded]    com.avid.driver.Avid_SCSI_RBC (1.2.0) [Click for support]
    [loaded]    com.cisco.kext.acsock (1.1.0 - SDK 10.2) [Click for support]
    [not loaded]    com.digidesign.fwfamily.driver (8.0.4f1) [Click for support]
    [not loaded]    com.digidesign.mbox2.boot.driver (8.0.4f1) [Click for support]
    [not loaded]    com.digidesign.mbox2.driver (8.0.4f1) [Click for support]
    [not loaded]    com.freecom.driver.BoulderScsi (1.0.0d1) [Click for support]
    [not loaded]    com.metakine.handsoff.driver (2.0.8 - SDK 10.6) [Click for support]
    [not loaded]    com.nvidia.CUDA (1.1.0) [Click for support]
    [not loaded]    com.paceap.kext.PACESupport (5.7.2b8) [Click for support]
    [not loaded]    com.paceap.kext.PACESupport2 (5.7.2b8) [Click for support]
    [not loaded]    com.paceap.kext.pacesupport.master (5.7.2b8) [Click for support]
    [loaded]    com.rogueamoeba.HermesAudio (3.0.1) [Click for support]
    [not loaded]    com.sony.filesystems.pdudf (4.03.0d006 - SDK 10.6) [Click for support]
    [not loaded]    com.sony.filesystems.pdudfr (4.03.0d006 - SDK 10.6) [Click for support]
    [not loaded]    com.sony.scsi.PDW-U1 (4.03.0d006 - SDK 10.6) [Click for support]
    [not loaded]    com.wacom.kext.pentablet (5.3.5 - SDK 10.9) [Click for support]
        /System/Library/Extensions/PACESupportFamily.kext/Contents/PlugIns
    [not loaded]    com.paceap.kext.pacesupport.leopard (5.7.2b8) [Click for support]
    [not loaded]    com.paceap.kext.pacesupport.panther (5.7.2b8) [Click for support]
    [loaded]    com.paceap.kext.pacesupport.snowleopard (5.7.2b8) [Click for support]
    [not loaded]    com.paceap.kext.pacesupport.tiger (5.7.2b8) [Click for support]
Startup Items: ℹ️
    ciscod: Path: /System/Library/StartupItems/ciscod
    CUDA: Path: /System/Library/StartupItems/CUDA
    Digidesign Mbox 2: Path: /Library/StartupItems/Digidesign Mbox 2
    DigidesignLoader: Path: /Library/StartupItems/DigidesignLoader
    PACESupport: Path: /Library/StartupItems/PACESupport
    ProTecVb: Path: /Library/StartupItems/ProTecVb
    Startup items are obsolete in OS X Yosemite
Problem System Launch Daemons: ℹ️
    [unknown]    c om.apple.coreservices.appleevents.plist [Click for support]
    [unknown]    c om.apple.diskarbitrationd.plist [Click for support]
    [unknown]    c om.apple.mDNSResponder.plist [Click for support]
    [unknown]    co m.apple.securityd.plist [Click for support]
Launch Agents: ℹ️
    [not loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
    [loaded]    com.adobe.CS5ServiceManager.plist [Click for support]
    [loaded]    com.cisco.anyconnect.gui.plist [Click for support]
    [running]    com.epson.epw.agent.plist [Click for support]
    [loaded]    com.google.keystone.agent.plist [Click for support]
    [running]    com.metakine.handsoff.agent.plist [Click for support]
    [loaded]    com.nvidia.CUDASoftwareUpdate.plist [Click for support]
    [failed]    com.parallels.desktop.launch.plist [Click for support]
    [loaded]    com.parallels.DesktopControlAgent.plist [Click for support]
    [running]    com.parallels.vm.prl_pcproxy.plist [Click for support]
    [running]    com.wacom.pentablet.plist [Click for support]
    [running]    net.culater.SIMBL.Agent.plist [Click for support]
    [loaded]    org.macosforge.xquartz.startx.plist [Click for support]
Launch Daemons: ℹ️
    [loaded]    com.adobe.fpsaud.plist [Click for support]
    [loaded]    com.adobe.SwitchBoard.plist [Click for support]
    [failed]    com.autodesk.backburner_manager.plist [Click for support]
    [running]    com.autodesk.backburner_server.plist [Click for support]
    [failed]    com.autodesk.backburner_start.plist [Click for support]
    [running]    com.cisco.anyconnect.vpnagentd.plist [Click for support]
    [running]    com.digidesign.fwfamily.helper.plist [Click for support]
    [running]    com.edb.launchd.postgresql-8.4.plist [Click for support]
    [loaded]    com.google.keystone.daemon.plist [Click for support]
    [running]    com.metakine.handsoff.daemon.plist [Click for support]
    [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
    [running]    com.parallels.desktop.launchdaemon.plist [Click for support]
    [loaded]    com.rogueamoeba.hermes.plist [Click for support]
    [loaded]    com.rogueamoeba.instanton-agent.plist [Click for support]
    [loaded]    org.macosforge.xquartz.privileged_startx.plist [Click for support]
    [loaded]    PACESupport.plist [Click for support]
User Launch Agents: ℹ️
    [loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
User Login Items: ℹ️
    Google Chrome    Application Hidden (/Applications/Google Chrome.app)
Internet Plug-ins: ℹ️
    o1dbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
    Google Earth Web Plug-in: Version: 7.0 [Click for support]
    Default Browser: Version: 600 - SDK 10.10
    Flip4Mac WMV Plugin: Version: 2.3.8.1 [Click for support]
    WacomTabletPlugin: Version: WacomTabletPlugin 2.1.0.6 - SDK 10.9 [Click for support]
    Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Click for support]
    FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
    Flash Player: Version: 16.0.0.305 - SDK 10.6 [Click for support]
    QuickTime Plugin: Version: 7.7.3
    googletalkbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
    SharePointBrowserPlugin: Version: 14.3.8 - SDK 10.6 [Click for support]
    iPhotoPhotocast: Version: 7.0
    JavaAppletPlugin: Version: 15.0.0 - SDK 10.10 Check version
User internet Plug-ins: ℹ️
    Picasa: Version: 1.0 - SDK 10.4 [Click for support]
Audio Plug-ins: ℹ️
    DVCPROHDAudio: Version: 1.3.2
3rd Party Preference Panes: ℹ️
    CUDA Preferences [Click for support]
    DigidesignMbox2 [Click for support]
    Digidesign Mbox 2 Pro [Click for support]
    Flash Player [Click for support]
    Flip4Mac WMV [Click for support]
    MacFUSE [Click for support]
    Perian [Click for support]
    PenTablet [Click for support]
    XDCAM Drive Monitor [Click for support]
Time Machine: ℹ️
    Skip System Files: NO
    Mobile backups: ON
    Auto backup: YES
    Volumes being backed up:
        Macintosh HD: Disk size: 498.88 GB Disk used: 408.02 GB
    Destinations:
        Time Capsule [Local]
        Total size: 799.52 GB
        Total number of backups: 18
        Oldest backup: 2014-11-12 02:44:18 +0000
        Last backup: 2015-02-17 14:14:45 +0000
        Size of backup disk: Too small
            Backup size 799.52 GB < (Disk used 408.02 GB X 3)
Top Processes by CPU: ℹ️
        20%    mds
         5%    WindowServer
         2%    Google Chrome
         1%    launchd
         1%    prl_disp_service
Top Processes by Memory: ℹ️
    515 MB    Final Cut Pro
    378 MB    softwareupdated
    309 MB    Google Chrome
    215 MB    Google Chrome Helper
    206 MB    mds_stores
Virtual Memory Information: ℹ️
    220 MB    Free RAM
    3.56 GB    Active RAM
    3.34 GB    Inactive RAM
    1.45 GB    Wired RAM
    7.56 GB    Page-ins
    4 MB    Page-outs
Diagnostics Information: ℹ️
    Feb 18, 2015, 04:35:18 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Last.fm Scrobbler_2015-02-18-163518_[redacted].crash
    Feb 18, 2015, 04:29:01 PM    /Library/Logs/DiagnosticReports/backburnerManager_2015-02-18-162901_[redacted]. crash
    Feb 18, 2015, 04:11:30 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Last.fm Scrobbler_2015-02-18-161130_[redacted].crash
    Feb 18, 2015, 04:04:44 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Last.fm Scrobbler_2015-02-18-160444_[redacted].crash
    Feb 18, 2015, 01:49:37 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Last.fm Scrobbler_2015-02-18-134937_[redacted].crash
    Feb 17, 2015, 05:36:32 PM    Self test - passed

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Shut down from safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Monitors flickering badly after Yosemite Install

Monitor flickering badly after Yosemite installed
I will be awaiting upDated drivers in a release soon.
I notice is very badly when I connect my iphone to ITunes screen
goes crazy flicker. . . . Anyone else having this issue ?

Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
     Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
     COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the
     computer and after the chime press and hold down the OPTION key until the boot manager
     screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Plugin sandbox errors after yosemite install

After Yosemite install I see MANY errors in my system.log like this:
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/AirDrop .appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/Faceboo kProfilePic.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/FlickrI mage.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/LinkedI n.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/ShareMa il.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/ShareMe ssages.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/SinaWei bo.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/SystemA ddToiPhoto.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/SystemS etAccountPicture.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/SystemS etDesktopImage.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/Tudou.a ppex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/Twitter ProfilePic.appex: plug-ins must be sandboxed
Oct 20 11:04:35 Yumi.local pkd[366]: ignoring mis-configured plug-in at /System/Library/PrivateFrameworks/ShareKit.framework/Versions/A/PlugIns/Youku.a ppex: plug-ins must be sandboxed
It goes for many software, like ShareKit.framework, SceneKit.framework, NotificationCenter.framework, Preview.app, Calendar.app, Reminders.app etc. - all of them are Apple software. I get it like every 1 minute in log.
Google didn't help. What is it, what does it means and how to fix?..

Problems such as yours are sometimes caused by files that should belong to you but are locked or have wrong permissions. This procedure will check for such files. It makes no changes and therefore will not, in itself, solve your problem.
First, empty the Trash.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Triple-click anywhere in the line below to select it, then drag or copy it — do not type — into the Terminal window:
find . $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 -o -acl $ -exec ls -Odel {} \; | wc -l
Press return. The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
The output of this command, on a line directly below what you entered, will be a number such as "85." Please post it in a reply.

Bootcamp Wont Load After Yosemite Install

Loner T,
My bootcamp does not load after Yosemite install.
Thanks

This is the first part of the recovery procedure. In your case, you have two OS X versions, so standard layout is not usable.
Please install GPT Fdisk (aka gdisk) (http://sourceforge.net/projects/gptfdisk/) if you have not done so yet.
You need to use the following steps. If you see any error messages during the following steps, please stop and post back here with the error message. The following steps have values from your Testdisk output (and you can verify) in Steps 7 and 8.
Rebuild GPT5 using start/end offsets
Sudo gdisk /dev/rdisk0
P (print the full list of parts)
D (delete)
5 (part 5)
N (new part)
5   (part 5)
841717760 - Start offset in bytes (start point for Bootcamp part)
+135055353 (Size offset as opposed to End offset)
0700     (Windows part type)
P           (print list of all parts just to see what changes will be made)
W         (Write the new GPT)
Y           (Yes! really write the new GPT)
This will delete and re-write the GPT partition info for /dev/disk0s5.
Reboot. Test that you can see the Bootcamp volume in Finder and see files in the Bootcamp volume.

Multiple Safari hangs after installing Snow Leopard

I had 5 Safari hangs today within hours...never had one since I bought the machine in June 2009 with Leopard installed...Since the SL upgrade CD, I have had 2 system freezes that result in a complete shutdown to clear and multiple Safari hangs that I able to recover with a force quit..My daughter in college with the same machine reported that she had 3 system freezes in one day since SL...My wife who did NOT yet install the SL upgrade and is now blissfully having no problems at all and does not want to install the new OS (again same machine type, We bought 3of them in June after the announcement). I hope that this gets debugged and fixes provided...

Hi,
Mac OS X 10.5: What you can do if Safari quits unexpectedly
That links is for 10.5 but the trouble shooting will work in 10.6 also.
For system freezes try maintenance.
Maintaining Mac OS X
On the Macs you upgraded to SL, did you check to see if you had 3rd party software installed that might not be compatible? http://support.apple.com/kb/HT3258
Did you repair permissions after the upgrade?
Quit any open applications/programs. Launch Disk Utility. (Applications/Utilities) Select MacintoshHD in the panel on the left, select the FirstAid tab. Click: Repair Disk Permissions. When it's finished from the Menu Bar, Quit Disk Utility and restart your Mac. If you see a long list of "messages" in the permissions window, it's ok. That can be ignored. As long as you see, "Permissions Repair Complete" when it's finished... you're done. Quit Disk Utility and restart your Mac.
Carolyn

Share in Safari shows No Services after Yosemite install?

I am unable to use the Share feature in Safari like I did before the Yosemite install. Under File and on the Task bar it is showing No Services. I checked every setting under Safari preferences and also System Preferences, no luck. Any suggestions? My friend has updated to Yosemite of his 2 laptops and does not have this issue. I am using a iMac (mid 2011)

To Restore Share Options
Open Macintosh HD > Applications > Utilities > Terminal > Copy and paste in the following:
/System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/LaunchS ervices.framework/Versions/A/Support/lsregister -kill -seed
> Press Return > Close Terminal App.
Hope that helps,
Weston
Supporting Article
If sharing options and Markup are missing after you install OS X Yosemite

Safari hangs after Yosemite install;

Similar Messages

Maybe you are looking for