Safari pinwheels and freezes the entire system.

Safari pinwheels and freezes the entire system.
I've read numerous threads with this Safari pinwheeling theme, but none of the posted solutions I've found work for me.
The problem:
Safari will almost always on opening, and frequently when filling in forms on websites, start pinwheeling. The whole system then slows down, and then eventually freezes. Even the dock bar freezes. When this happens, I can't even bring up the Force Quit bar. The freezing will often last several minutes, then all of a sudden, all my various previously ignored mouse and key clicks cycle through. When Force Quit finally starts, then everything freezes again. Eventually, Force Quit will show Safari as not responding, and once in a while the system then will start responding, but usually I have to kill Safari.
The problem subsided a little bit on the opening the application problem when I switched my start page from Apple.com to Google.com, thinking that maybe it was just too much graphics crap coming in on the Apple site.
The problem happens on both my Airport and cell modem network connections.
I may have seen this behavior once with Firefox, but haven't been able to reproduce it.
Generally I only have a few things running: Excel, Messenger, Safari.
Things I've tried to fix this:
Reset Safari
Clear Safari Cache
Delete Safari folder in the system cache folder
Went into the Energy Saver in Preferences and unchecked, "put disk to sleep when not in use" for both the battery and power adpater settings
Limit number of tabs open
I'd try restarting Safari occasionally, but the problem usually happens on opening.
I've emptied the trash, and made sure there is ample open disk space (10gb right now).
Resolved duplicate fonts.
I have no third party apps to affect Safari or networking.
I've reset the machine by unplugging it and holding the power button.
My computer is a MacBookPro 15" with all the latest software and firmware updates and 2gb RAM. This has become so frustrating, it's been very tempting to just throw the laptop at the wall and go back to my Windows laptop...

I'd say the bad blocks were behind the problems you were seeing. Their existence points to either a defective HD, or directory corruption. The latter usually can be repaired by using a Utility such as Disk Warrior, or as you did, reformatting the drive.
Best approach to minimizing directory problems is to do routine maintenance twice a month. Have a look at this MacWorld article for suggestions.
For routine maintenance I use OnyX. There is no charge for the software, but I believe the developer asks for a donation.
It's very easy to use. I run it twice a month. Once it is installed, you would double click on the OnyX icon in your application folder (or drag an icon to your dock for quick access) to open the application. After entering your administrator password, you would select "automation". The panel looks like this:
Select the same items I have checked. The program takes about 5 to 10 minutes to run. Leave your computer alone, that is, don't use it for anything else until OnyX is finished. Once complete, restart the computer and you're good to go.
Lastly, the most effective maintenance is having a full backup of your system on an external hard drive. All machines fail eventually, despite the best maintenance. If you had a hard drive failure without any backup, then you would lose all your information, including documents, images, songs, etc. Not a pretty picture.
For your system, you would purchase either a USB or Firewire Drive for your new Intel Machine. The key here is creating a "clone" backup on the drive, which you back up regularly, or at least once a week. For the backup process I use SuperDuper. Very easy to use. The initial backup takes about 1 to 2 hours. Subsequent backups take 5 to 10 minutes. Total $$$ investment can be anywhere between $100 - $250 depending on the size of your Hard Drive.
Post back if you need any other information relative to your questions here.

Similar Messages

[Solved by moving to Ubuntu] VirtualBox freezes the entire system

Hello everyone,
I have some major issues with VirtualBox, I have recently installed it for the first time, but it just randomly freezes my entire system. There shouldn't be any load on the processor for this to happen. I don't really know what the cause is. I tried both Windows XP and Windows 7 as guest systems with the same sad outcome. The host and guest freeze and I have to do a hard restart. There always is some noise that comes from the sound card and, in the case of VMWare, from the case speaker.
I tried disabling AMD-V - using a Phenom II x4 955 - but it didn't work. I also tried adding nohz=off to the grub line but it also didn't work. I have recompiled the kernel modules after the last kernel update - 2.6.32. I can't really say whether it's only related to the last kernel update or not as I only started using it after the update.
It seems that I have similar issues with VMWare player.
Here's my system information:
Arch64
Kernel 2.6.32
Phenom II x4 955
4 GB of ram
Virtualbox 3.1.2-2 from the AUR
This only issue occurs with VirtualBox and VMWare, I did test the memory and it's okay. I also have plenty of fans - 2x120mm + 2x80mm - and my system temperature (using k10temp) never goes above 48 c under load. So, it isn't an issue with overheating.
Does anyone have any similar issues? Do you have any suggestions for this?
Thanks!
Last edited by DavidR (2010-01-21 23:54:22)

Should I ask to have this thread moved to the 'Pacman & Package Upgrade Issues'? Will anyone be able to help there? I am seriously starting to consider downgrading the kernel once again and seeing whether it will work.
Does anyone have a machine with another 64-bit distro with this kernel version? If so, can the problem be replicated there? I don't know whether this is really related to Arch or the kernel. Should I file a bug report somewhere? and if so, where can I do it?
http://www.archlinux.org/news/477/
May it be related to the xen support that has been added to Arch64?
Last edited by DavidR (2010-01-14 08:18:30)

Premiere Pro CC2014 freezes the entire system

New Mac Pro - late 2013
PP CC 2014
OS 10.9.3
Recent convert from FCP7. Basically can't get any work done. PP hangs up and causes the entire machine to hang up, requiring a hard restart. This sometimes happens as previews are being loaded, sometimes when doing actual work, somethings when just moving the playhead around. Working with Red footage from 4-6k. I have trashed prefs multiple times and followed the 13 step process regarding sharing and permissions posted here and on Cow. I have unplugged every peripheral device except for the monitors and a 24TB Pegasus. Sometimes the machine will be stable for a bit, sometimes it hangs as soon as it is opened. Getting in 15 minutes of uninterrupted work is a reason to celebrate. Appreciate your help.

I too recently converted from FCP to Premiere. I was using the the previous version of Premiere Pro CC and it worked great! When I update to Premiere Pro CC 2014, it started crashing routinely. I'm on a Win7 machine with no plug in's and 2014 has not worked on it. I went back to the previous version and all is well .If you are under the gun and need to get some serious work done, I recommend uninstalling 2014 and downloading the previous version of Premiere.

Safari crashes and freezes the Imac

About once a day, Safari causes the Mac to freeze completely at least once a day. Though I can move the mouse, the only way out is to restart the computer by pressing on the power button.
The problem has been going on since Lion. I'm now on 10.10.2 with Safari 8.0.3.
I suspect it has something to do with my user account, because I cannot fully load a website like Linkedin on my account, but can do it no problem on a guest account.
I've deleted caches (both manually and from the browser), plist, cookies and everything from Safari, with no success.
Anyone's got a hint ?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1257 ' 0.5 0.25 10 1000 15 5120 1000 25000 1 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1 250 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 1024 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile AirPort 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:Mb/s:ms/s:KiB/s:%:total:MB:total:per sec' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' CFBundleIdentifier );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' %s{' ','\n'{"${k[22]}",}}'%s\n' '%.1f GiB: %s\n' '\n    ...and %s more line(s)\n' '\nContents of %s\n    '"${k[22]}"'mod date: %s\n    '"${k[22]}"'checksum: %s\n%s\n' );c=(879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' BEGIN { FS="\f";if(system("sw_vers -productVersion|grep -q ^10\.1")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' $1>1{$NF=$NF" x"$1} /\*/{if(!f)f="\n\t* Code injection"} {$1=""} 1;END{print f} ' ' NR==2&&$4<='${p[7]}'{print $4} ' ' BEGIN{FS=":"} ($1~"wir"&&$2>'${p[22]}') {printf("wired %.1f\n",$2/2^18)} ($1~/P.+ts/&&$2>'${p[19]}') {printf("paged %.1f\n",$2/2^18)} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q"\f"$0"\f"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/, .+:/{print};END{if(NR<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { print "/L.+/Scr.+/Templ.+\.app$";print "/L.+/Pri.+\.plugin$";if(NR<'{${p[14]},${p[21]}}') print "^/[Sp].+|'${k[21]}'";} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt))$/p;' ' BEGIN{ FS="= "} $2 { gsub(/[()"]/,"",$2);print $2;} ' ' /^\//!d;s/^.{5}//;s/ [^/]+\//: \//p;' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' BEGIN{FS=": "} /^ {10}O/ {exit} /^ {0,12}[^ ]/ {next} $1~"Ne"&&$2!~/^In/{print} $1~"Si" { split($2,a," ");if(a[1]-a[4]<'${p[5]}') print;};$1~"T"&&$2<'${p[20]}'{print};$1~"Se"&&$2!~"2"{print};' ' BEGIN { FS="\f";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS="\f";} $2<=m[$1]{next} $1<9 { o[$1]=o[$1]"\n    "$3" (UID "$4"): "$2;} $1==9&&$5!~"^/dev" { o[$1]=o[$1]"\n    "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==10&&$5 { p="ps -c -ocomm -p"$5"|sed 1d";p|getline n;close(p);if(n) $5=n;o[$1]=o[$1]"\n    "$5" => "$3" (UID "$4"): "$2;} $1~/1[12]/ { o[$1]=o[$1]"\n    "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+4;i++)u[i]=u[n];split("'"${k[28]}"'",l,":");for(i=1;i<13;i++) if(o[i])print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n    "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n    [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n    "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n    '"${k[22]}"'"T;printf("'"${f[8]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[33]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/, .+:/||b=="") b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/'$'\f''/;s/(\n)c/\1'$'\f''/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */    /;p;' ' s/^.+ |\(.+$$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2 \1/p' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/'$'\f''(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8}$'\f''/;s/ *'$'\f'' */'$'\f''/g;p;' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS="\f"} { printf("'"${f[6]}"'",$1/2^30,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") D=D"\n"$1;} END { print D;} ' ' BEGIN{FS="\t"} NR>1&&$NF!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $NF"\f"a[split($(NF-1),a," ")];} ' '|tail -n'{${p[6]},${p[10]}} ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li).+|Bus): .|d: Y/d;s/:$//;$d;p;' ' BEGIN { RS=",";FS=":";} $1~"name" { gsub("\"","",$2);print $2;} ' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' /^ +N.+: [1-9]/ { i++;} END { if(i) print "system: "i;} ' ' NF { print "'{admin,user}' "$NF;exit;} ' ' /se.+ =/,/[\}]/!d;/[=\}]/!p ' ' 3,4d;/^ +D|Of|Fu| [0B]/d;s/^ |:$//g;$!H;${ x;/:/p;} ' ' BEGIN { FS=": ";} NR==1 { sub(":","");h="\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;L[i]=l" "$2;if(i=='${p[24]}') nextfile;} END { if(i) print h;for(j=0;j<i;j++) print L[i-j];} ' ' /./H;${ x;s/\n//;s/\n/, /g;/,/p;} ' ' {if(int($6)>'${p[25]}')printf("swap used %.1f\n",$6/1024)} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk 'dscl . -read' networksetup mdutil lsof test osascript\ -e netstat mdls route cat );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop {/,}L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|(allow|call)ing|(mplet|nabl)ed|ry HD|safe b|xpm' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA[(]|pagin|Purg(ed|in)|error|Refus|TCON|tim(ed? ?|ing )o|trig|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1\f%@d\f%s\f%d\n\",@a);printa(\"2\f%@d\f%s\f%d\n\",@b);printa(\"9\f%@d\f%s\f%d\f%s\f%d\n\",@c);printa(\"10\f%@d\f%s\f%d\f%d\n\",@d);printa(\"11\f%@d\f%s\f%d\f%d\n\",@e);printa(\"12\f%@d\f%s\f%d\f%d\n\",@f);printa(\"3\f%@d\f%s\f%d\n\",@g);printa(\"4\f%@d\f%s\f%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag $ -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f'$'\f''%Sc'$'\f''%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{auto*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list '-F "" -k Sender hidd -k Level Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' print\ system --dns -get{dnsservers,info} dump-trust-settings\ {-s,-d,} -n1 '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |jnl_io.+)err','USBF:.+bus'}'"' -name\ kMDItem${k[33]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[33]} :CFBundleDisplayName $EUID {'$TMPDIR../C ','/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s -type f -size +'${p[11]}'G -exec stat -f%z'$'\f''%N {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' 'L*/A*/Fi*/P*/*/a*.json' users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$(Sender): \$Message" -k Sender Rne launchd -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "[{}<>]|commit - no t|deprec|fmfd|Goog|ndum|realp|sandbox ex|/root" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[33]}'=*"' -m\ / '' ' -F "\$Time \$(RefProc): \$Message" -k Sender Req launchd -k Level Nle 3 -k Message Rne "asse|bug|hij|Ig|Jet|lid t|Plea" ' vm.swapusage );N1=${#c2[@]};for j in {0..20};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console,launchd}\ log SMC Login\ hook 'I/O per process' 'High file counts' UID Daemons Agents XPC\ cache Startup\ items {Admin,Root}\ access Stylesheet Library\ paths{,' ('{shell,launchd}\)} Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ {caches/logs,overrides} Shutdown\ codes Heat Diagnostic\ reports Bad\ plists Free\ space 'VM (GiB)' Bundles{,' (new)'} Trust\ settings Activity );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d$'\e' <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F$'\e' ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 27;B1&&! B2&&C2 28;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99; for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 32 70 101 25;D2 65 6 76 13;D2 45 20 52 66;A1 7 77 14;B3 28;A1 20 79 111;B6 0 28 5;B4 0 0 110;C2 66;D4 70 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 31 25 77 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 32;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 25 22 20 32;D2 33 0 N1+14 51;for i in {0..2};do A1 29 35+i 104+i;B3 25+i;done;B6 25 27 5;B6 0 26 5;B4 0 0 110;C2 69;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 81;B3 18;A1 33 60 82;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 0 N1+20 43;B2&&D4 59 4 65 76 91;D4 63 4 19 44 75 95 12;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 96;D4 15 5 72 96;D4 17 5 78 96;C4;};D4 16 5 73 96;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 50;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 18 31 107 94 74||{ B2&&A1 18 26 94 74;}&&{ B7 11;B4 0 0 11;C3 23;};A1 18 26 94;B7 11;B4 0 0 11;C3 24;D4 60 14 66 92;D4 58 14 67 93;D4 26 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 29 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 108; A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B3 15;B6 14 15 4;C3 67;A1 24 75 74;B3 23;A2 39 57 30;B3 24;B6 23 24 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 30;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;D0 0 N1+18 109;D4 7 11 6;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I may not agree with them.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Apple Mail freezes the entire system

This just started today after absolutely no problems with my system in the last 20 months of ownership.
This morning I got the spinning beach ball and my computer became completely unresponsive. I could not force quit any apps or switch between them. I thought it was something to do with iTunes because it tends to be less than snappy at start up due to a lot of music and video however, that wasn't the issue. After a few hours of messing about, disconnecting peripherals and turning off time machine it became evident that Apple Mail was causing the trouble.
I'm pretty good at pruning my mail and emptying the trash and I've also used disk tools to repair the disk permissions. I don't save drafts to the server and I don't add invitations to iCal.
I haven't added any new applications and the only recent update was the iTunes update that I installed after the trouble started.
As long as I don't launch Mail, the computer is golden. If I do launch it there is a minimum of 5 minutes of innactivity and at any time it might go awry and cause another 3 - 5 minute period of completely useless innactivity.
Any thoughts? I know Mozilla will take over quite nicely but I don't want to switch mail clients because Apple Mail has been just fine since I started using it with exception to today.
Thanks,
Andrew

Hi, I haven't actually tried this in 10.6.x, or maybe I have & forgot!
Not certain, but this can fix myriad Mail problems...
Safe Boot from the HD, (holding Shift key down at bootup), it will try to repair your Disk Directory while the spinning radian is happening, so let it go, run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, then move this folder & file to the Desktop.
Move this Folder to the Desktop...
/Users/YourUserName/Library/Caches/Mail/
Move this file to the Desktop...
/Users/YourUserName/Library/Mail/Envelope Index
Reboot.
If that doesn't do it and you can afford to redo all your Rules, try these & reboot...
/Users/YourUserName/Library/Mail/MessageRules.plist
/Users/YourUserName/Library/Mail/MessageRules.plist.backup

Wicd hangs, freezing the entire system

Hi everybody.
So, i just installed Arch on my laptop, and everything went fine, more or less. during the installation process, i was using the manual connection method using netcfg which works pretty well. but once i got a desktop manager installed and working (LXDE, in case it matters which i doubt), i thought it would be nice to have a gui front end to make things quicker.
i installed and then network manager (nm applet et al) but there were a bunch of issues so i just uninstalled it and got wicd.
wicd works mostly, but it VERY frequently hangs the system. when i boot up into a gui, it freezes entirely for a few seconds, but then unfreezes again and i'm able to log in. if i open the gui tray thing for it and ask it to scan, disconnect from all, or connect, four times out of five the CPU usage will skyrocket to a hundred percent and i wont even be able to move the mouse or switch to a virtual terminal and i have to power down with the physical switch.
the (/var/log/wicd/wicd.log) shows nothing interesting when its doing that but when i reboot it has a line "Exception KeyError(140400652642048,) in <module 'threading' from '/usr/lib/python2.7/threading.pyo'> ignored". probably nothing.
if i take it out of my daemons array everything is fine. i can connect without it using only the wireless tools package but it would be nice to have it working.
sorry for the long post. anybody know anything about this? the problem also happens when i use wicdcurses too, so it's not just the frontend.

realteck (spelling is wrong) 8188 is the card. i think i was using nm-applet for a very brief while, but it didnt work either (wouldnt connect to wireless) so instead of dealing with it i just went to netcfg, which works quite well indeed.
as for the freezes, occasionally i would be able to get top open before it happened and it said that wicd was using obscene amounts of CPU time right before the system locked up. for whatever that's worth. not much, really. yeah i've never known a linux machine to crash in that way before.
anyway, i would suggest, if you're down with command lines, that you might give netcfg a try for a while. i cant really call that a solution to the problem, but it did work for me and i didnt have to do anything with new kernels or the like.
good luck

Safari and Firefox are FREEZING the entire OS requiring hard reboot.

Hello new user here.
I have been working on a client computer:
Dual 2.7 G5 Tower with 8GB Ram (early 2005), only mouse and keyboard plugged into USB port.
Installed on new HD with clean install from Leopard 10.5.6 Install Disk. Updated to OS X 10.5.8, all apple updates and firmware updates applied.
ASD for the system PASSED all tests and on multiple loops.
MEMTEST Passed, no errors
Temperature monitor within safe ranges under 70C for everything.
Temperature Calibration of the chips completed through ASD
No dust in the case, no leaks detected, no evidence of leaks either.
Through diagnostics and testing original components by using replacing with known good components show that the hardware is SOLID. All the tower components passed the Apple Diagnostics and tested as WORKING in other towers.
Permissions Fix = completed
Deleted the browser preferences, deleted caches, etc etc.
The system is CLEAN CLEAN CLEAN
So when I got to run Safari, it crashes within 1 minute and takes out the entire system with it. Firefox will do the same but in 5 minutes or so. Opera browser WORKS. (But that doesn't solve the problem of why Safari and Firefox are hosing the system.
I also tried this on wired lan, and a wireless lan, and a USB data modem (AT&T), and changed MTU, etc etc etc. The network is SOLID.
I am a 15 year experienced desktop IT tech working on PCs and MACs and I am completely stumped.
I can duplicate it each and every time. Browsing on google, cnn, yahoo, will crash the system.
Here is something odd too. I ran folding at home for > 48 hours on this machine and came back over the weekend and it was FINE. The second I started up a Safari, it crashed that a reboot was required to recover.
Any ideas? Any help appreciated.

Hi stantony1, and a warm welcome to the forums!
Wow, great work so far!
Temperature monitor within safe ranges under 70C for everything.
Hopefully way under, like under 60°C.?
MEMTEST Passed, no errors
The Memory test can really only be trusted if it finds a problem, not if it doesn't find a problem.
Memtest OS X...
http://www.memtestosx.org/joomla/index.php
Rember is a freeware GUI for the memtest ...
http://tech.kateva.org/2005/10/rember-freeware-memory-test-utility.html
One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Does ȃfari crash it in Safe Mode???
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
Reboot, test again.
If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport in 10.4 & below.

I have an Apple Macbook and will be backing up the entire system to an external hard drive utilizing the Time Machine application. when I am doing this, will the data on the external drive that I am using be erased?

I have an Apple Macbook and will be backing up the entire system in order to upgrade to a newer OS. I will be using an external hard drive to do this and there is already data on it. To complete the backup, i will be using the Time Machine application. Does this application wipe out all of the existing data on the external hard drive, or will it create a new "folder" for the backup?
thank you

No, but as steve359 states you should use a dedicated hard drive for backups. It you need a temporary backup then you can use the drive provided it has sufficient space for all your data on the hard drive.
When Time Machine finds that the drive has data on it already it may decide to erase the drive before continuing, which is another reason to use a dedicated drive.

I have lost my Safari app and all the bookmarks that go with it. I have tried to download my back-up on external drive but cannot access it. Tried a start with C key held down but still no access to the back-up app.

I have lost my Safari app and all the bookmarks that go with it. I have tried to download my back-up on external drive but cannot access it. Tried a start with C key held down but still no access to the back up app.
Have used Superduper app. to back up and checked back-up occasionally to see if all files present and appeared OK.
I had previously started machine using original CD #1 to try and replace Eudora which was acting up. Did not knowingly touch Safari.
Running iMAC System 10.4.11
How can I successfully download from the Maxtor back-up?
Ivan

Further info.
I checked the content of my other back-up and found the bookmark Bookmarks.plist in the library under Safari
Dumped the existing copy in the computer and drag-dropped the back up. All bookmarks restored.
Solved the Stickies problem by using Spotlight to find file "stickiesdatabase" and did a drag- drop to replace file. All data restored.
Re Ical data loss. Used Spotlight to find iCal document in Library - Preferences where I found com.apple.iCal.plist in folder.
Got ready to make change but did not immediately remove file. When I returned to Preferences folder to grab above document,
the readable descriptors had been changed to code consisting of some upper case letters and/or single symbols!
So now I cannot tell which is the symbol iCal.plist
Thanks for leading me so far, but how do I find that plist for my calendar?

How to read the source file and copy the entire content to the target Database field

Hi All,
PI system extracts the actual business content from the incoming attachment file and copy the entire format to the target Database field which is a blob data type field.
Sender Adapter: SOAP
Receiver Adapter: JDBC
JDBC Structure
Can we achived the above requirement by using UDF with out Java Mapping?
Thanks,
Mahi.

Ok, in this case yo can use the conten converion of the file adapter. Therefore you first need to create a Datatype in ESR with the required structure
Then in your file adapter you need to use this datatype and its required fields:
The Datatype then can be used as usual within you mapping.
regards
Christian

Is there a way to restrict changing the browsing history in safari with ought restricting the entire application?

Is there a way to restrict changing the browsing history in safari with ought restricting the entire application?

For the iPod touch in your profile?
Private browsing help here > iOS: Safari web settings
For Safari for Mac OS X ...
From your Safari menu bar click Safari > Private Browsing
You can only block all history in Private Browsing, pages you visit, and autofill.

How to delay the audio to lip sync? (of the entire system)

I`m using a LED 32" LG screen via hdmi, but the audio is outputing directly via usb to my Mbox Mini, and the image have a small delay (5 frames) but the audio not, so the result is out of sync videos.
Of course there`s tons of apps that can solve the problem by compensating, like VLC and MPlayer X, but the problem is that i`m a video editor and use FCP and Motion all the time. For playbacking with these apps (after making the 5 frames compensation) turns into a perfect results, but during video editing it`s a pain to lip sync.
Of course as i know that the delay is 5 frames, when i output i could delay the entire audio, but it would be a pain making this everytime and for internet streaming the videos would still off sync.
There`s anyway i can delay the audio of the entire system?
PS: I`m using Lion 10.7,

> I wonder if there is any way to delay the opening of a
MIAW. In particular i
> have the following
If you want other activity to take place, you could use a
timeout object:
dialogue = window().new("D_XML_Test (Greek2)")
dialogue.filename = "path to file"
t = timeout().new("mOpenWindow", 60000, #mOpenWindow,
dialogue)
-- #movie script:
on mOpenWindow aWindow, aTimeout
if ilk(aTimeout, #timeout) then aTimeout.forget()
if ilk(aWindow, #window) then aWindow.open()
end
If you don't mind locking out activity, you could use the
delay()
function, but I wouldn't recommend that approach

GuiXT valid throughout the entire system

<b>GuiXT</b>
I need to customize my VA01 transaction using GuiXT. But I dont want it
to be user-specific on user's PC but throughout the entire system.
The document that i have seen says that put the GuiXT script file on application server
for the same.
But I have seen that for every user there is Script1 . . Script4
directory setting and this is where the VA01 will look before loading.
So even if I keep the script file on the server, if these Script directory
is not set to the required path, it will not reflect any changes that i have
made.
SO will i have to go on each user machine and give the path
or is there a way out.

Hi Flora,
Have you looked transaction code <b>SHD0</b> to create transaction variant to customize SAP screen?
This transaction variant can be applied for user group or individual user.
For more information, please check this link.
http://help.sap.com/saphelp_nw04/helpdata/en/7d/f639fb015111d396480000e82de14a/content.htm
Hope this will help.
Regards,
Ferry Lianto

XMMS freezes the wholw system

xmms plays fine but when i select the opengl visualization plugin then it freezes the whole system. NO i can't even do the "C-M-F2/3/4" everything just freezes to hell and the only option is the "Restart button" of cabinet.
though i am using bmp now but i want to know why it happened. earlier i had similar system-freezes when i tried to access any floppy on Voodo.
Voodo i686 -> floppy access = system Freeze
Duke x86_64 -> xmms opengl visulazation-plugin = system-freeze
only one solution = Restart button of Cabinet (this way it feels WindowsXP :-(
any ideas ?

slackhack wrote:can you use openGL for other things?
i dont know for what other applications use OpenGL. "mplayer" is playing excellently.
slackhack wrote:i know openGL screensavers totally lock up my system like you describe after about a minute. what video card and drivers are you using? glxinfo looks okay?
using VIA K8M800 chipset on ASUS K8V-MX motherboard. VIA driver is in play and i use it on other distros without any trouble.
don't know about <glxinfo>, here it is:
[arnuld@arch ~]$ glxinfo
name of display: :0.0
display: :0 screen: 0
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_import_context, GLX_EXT_texture_from_pixmap,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_OML_swap_method,
GLX_SGI_make_current_read, GLX_SGI_swap_control, GLX_SGIS_multisample,
GLX_SGIX_fbconfig, GLX_SGIX_visual_select_group
client glx vendor string: SGI
client glx version string: 1.4
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_allocate_memory,
GLX_MESA_copy_sub_buffer, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_OML_sync_control,
GLX_SGI_make_current_read, GLX_SGI_swap_control, GLX_SGI_video_sync,
GLX_SGIS_multisample, GLX_SGIX_fbconfig, GLX_SGIX_pbuffer,
GLX_SGIX_visual_select_group, GLX_EXT_texture_from_pixmap
GLX version: 1.2
GLX extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_SGI_make_current_read,
GLX_SGI_swap_control, GLX_SGI_video_sync, GLX_SGIS_multisample,
GLX_SGIX_fbconfig, GLX_SGIX_visual_select_group
OpenGL vendor string: VIA Technology
OpenGL renderer string: Mesa DRI UniChrome (K8M800) 20060710
OpenGL version string: 1.2 Mesa 6.5.2
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multisample, GL_ARB_multitexture,
GL_ARB_point_parameters, GL_ARB_texture_env_add,
GL_ARB_texture_env_combine, GL_ARB_texture_mirrored_repeat,
GL_ARB_transpose_matrix, GL_ARB_window_pos, GL_EXT_abgr, GL_EXT_bgra,
GL_EXT_blend_color, GL_EXT_blend_minmax, GL_EXT_blend_subtract,
GL_EXT_clip_volume_hint, GL_EXT_compiled_vertex_array, GL_EXT_convolution,
GL_EXT_copy_texture, GL_EXT_draw_range_elements, GL_EXT_fog_coord,
GL_EXT_histogram, GL_EXT_packed_pixels, GL_EXT_point_parameters,
GL_EXT_polygon_offset, GL_EXT_rescale_normal, GL_EXT_secondary_color,
GL_EXT_separate_specular_color, GL_EXT_stencil_wrap, GL_EXT_subtexture,
GL_EXT_texture, GL_EXT_texture3D, GL_EXT_texture_edge_clamp,
GL_EXT_texture_env_add, GL_EXT_texture_env_combine,
GL_EXT_texture_lod_bias, GL_EXT_texture_object, GL_EXT_vertex_array,
GL_APPLE_packed_pixels, GL_IBM_rasterpos_clip,
GL_IBM_texture_mirrored_repeat, GL_MESA_window_pos, GL_NV_blend_square,
GL_NV_light_max_exponent, GL_NV_texgen_reflection, GL_OES_read_format,
GL_SGI_color_matrix, GL_SGI_color_table, GL_SGIS_texture_edge_clamp,
GL_SGIS_texture_lod
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x22 24 tc 0 32 0 r y . 8 8 8 8 0 24 8 0 0 0 0 0 0 None
0x23 24 tc 0 32 0 r . . 8 8 8 8 0 24 8 0 0 0 0 0 0 None
0x24 24 tc 0 32 0 r y . 8 8 8 8 0 16 0 0 0 0 0 0 0 None
0x25 24 tc 0 32 0 r . . 8 8 8 8 0 16 0 0 0 0 0 0 0 None
0x26 24 tc 0 32 0 r y . 8 8 8 8 0 0 0 0 0 0 0 0 0 None
0x27 24 tc 0 32 0 r . . 8 8 8 8 0 0 0 0 0 0 0 0 0 None
0x28 24 tc 0 32 0 r y . 8 8 8 8 0 24 8 16 16 16 16 0 0 Slow
0x29 24 tc 0 32 0 r . . 8 8 8 8 0 24 8 16 16 16 16 0 0 Slow
0x2a 24 tc 0 32 0 r y . 8 8 8 8 0 16 0 16 16 16 16 0 0 Slow
0x2b 24 tc 0 32 0 r . . 8 8 8 8 0 16 0 16 16 16 16 0 0 Slow
0x2c 24 tc 0 32 0 r y . 8 8 8 8 0 0 0 16 16 16 16 0 0 Slow
0x2d 24 tc 0 32 0 r . . 8 8 8 8 0 0 0 16 16 16 16 0 0 Slow

FCPX crashes the entire system when applying Ken Burns

When applying Ken Burns to an image, when repositioning the start and/or end frame the entire system locks up, not just FCPX. The cursor can still be moved, but other than that the entire system is unresponsive and the only solution is turning off my iMac and rebooting. That is how the problem started, a few days later during the same process the entire screen turns black and rebooting is once again the only way out.
Is anyone else familiar with this problem?

There's a little icon that appears in the Project on top of each picture that has Ken Burns applied, click on that icon (it's a cropping square icon). that will bring up the Inspector and show you the red/green boxes that indicate the area where the zoom starts and ends for Ken Burns. If you drag the edges of both the red/green boxes individually to fit the entire picture, I think you will get the effect of not cropping. But it won't really be Ken Burns either because it won't zoom/pan across the image as it plays back.

Safari pinwheels and freezes the entire system.

Similar Messages

Maybe you are looking for