Safely point an NSS VMDK to the new server during transferID

I have two VMWare VMDK NSS Volumes hosted on an iSCSI array for a class, connected to my existing OES2SP3 server. I'm installing a transfer ID server instance OES11SP2 I'd like to to migrate the "locally" hosted vmdk NSS volume over to the new server. (I don't have space to migrate the other two huge volumes.)
So I'm going to install the transfer id server and migrate the main STORAGE volume to it and then remove the two VMDKs from the OES2SP3 VM and install them onto the new OES11SP2 VM. I assume that I do this move after I finish the transfer ID from the old VM to the new VM.
My question I'm hoping to have answered is -> If you move an NSS VMDK to a server after the transfer ID occurs, will the new server have to have the existing NSS edir objects changed in any way or will it simply assume ownership of them when they are mounted at boot? Is it safe to move them after the transfer id or must I do it before. I didn't like the idea of yanking the two NSS volumes out from the old server prior to doing to transfer id.
Thanks,
-Nyle

Originally Posted by nlandas
I have two VMWare VMDK NSS Volumes hosted on an iSCSI array for a class, connected to my existing OES2SP3 server. I'm installing a transfer ID server instance OES11SP2 I'd like to to migrate the "locally" hosted vmdk NSS volume over to the new server. (I don't have space to migrate the other two huge volumes.)
So I'm going to install the transfer id server and migrate the main STORAGE volume to it and then remove the two VMDKs from the OES2SP3 VM and install them onto the new OES11SP2 VM. I assume that I do this move after I finish the transfer ID from the old VM to the new VM.
My question I'm hoping to have answered is -> If you move an NSS VMDK to a server after the transfer ID occurs, will the new server have to have the existing NSS edir objects changed in any way or will it simply assume ownership of them when they are mounted at boot? Is it safe to move them after the transfer id or must I do it before. I didn't like the idea of yanking the two NSS volumes out from the old server prior to doing to transfer id.
Thanks,
-Nyle
IF my memory serves (this was a while ago), we did it that way (leave the "old" disk attached). Transfer ID, power off both servers, disconnect "old" disk and reconnect to "new" server. Power up and I think it just worked. I don't recall having to re-run anything in nssmu.
But again, that WAS a while ago.

Similar Messages

I switched email servers and when I synced to the new server, all my old emails erased... HELP

I previously had 1&1.com hosting my email addresses ([email protected] & [email protected]) and I recently switched to Weebly/Gmail to host these email addresses...
I enabled IMAP forwarding in gmail (which in hinesight I think I should have selected POP) and when I updated my server settings in Thunderbird - all of my old emails disappeared. Theses emails are for business and I may have dramatically hurt our business by doing this.
Are emails backed up anywhere where I can restore from? I do have the option selected to store all emails on my local computer - please help :)

With IMAP all mail is managed on the server. By simply changing the server of an existing account you virtually start from scratch. I.e. the new server knows nothing about the mail on the old server.<br>
What you see in Thunderbird is basically a mirror of what's on the server.
What you should have done is moving messages off of the old server to your Local Folders account.<br>
Alternatively you could have created a new account with the same email address on the new server.
The Thunderbird IMAP synchronization option basically is a local offline copy of what's on the server. The offline copy got wiped out when you connected to the new server. It isn't an equivalent for a proper backup of your messages.
I don't know if you still have access to the old server. If not, then you can only restore a backup of your profile folder, assuming you've created one at some point.
It is grossly negligent not to backup your business email.

Folder Redirection did not update to the new server

hello guys, I had migrated quite some time ago to a new server.
I thought everything works fine, basically the server functionality DNS, Replication and other stuff works fine.
But I notice that some of the workstation did not actually update its folder redirection to the new server.
Their desktop and my documents still points to the old server.
So their offline files, is becoming larger and larger.
I have some workaround but it's a lot of work. Question is, why those Win 7 workstation folder redirection did not update to the new server.
What should be the best practice? During the migration process from the old server to the new server, all workstation should be turned on?
Or any tools to update those workstation to the new server without losing their files?
Basically, just editing the registry to point to the new server will help. But it means losing their current files and whatever old stuff that is on the server will be the one that will be shown on their desktop and documents.
any inputs is greatly appreciated.
Every second counts..make use of it. Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
IT Stuff Quick Bytes

Hi biswajeetpattnaik, before migration it was Windows 2003.
Then I introduce Windows 2008.
Then I introduce a new Windows 2012.
Now Windows 2012 is the main DC.
Actually, everything is under control right now. As what I said on my first post, I manage to do some work around.
The only question I have on mind, is how on earth this thing happen.
I was assuming, that the workstation will be able to point to the new server, without any glitch since everything is working fine.
And the GPO was applying on the workstation. If I type gpresult /v on the workstation is it being applied. Even if I run GP Modelling it is also shows on the result that the folder redirection is being applied.
But to my surprise the folder redirection still points to old server, if I have not discovered it then it would be difficult if some files will get lost.
Thanks for your reply.
Every second counts..make use of it. Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
IT Stuff Quick Bytes

Problem with the new server UCS C220 for set IP to CIMC

Hi
We’ve a problem with the new server UCS C220.
We bought two servers UCS C220 M3 for CallManager 8.6 with High Availability.
When we turn on the server during the boot and when it tells us, oppress F8 to enter at the CIMC and set the IP. But it never enters at the CIMC.
Then, we configure our DHCP server and our switch, we connect the three gigabyte ports to our switch to give him an IP to the CIMC, so and then can enter via browser, but neither works.
Note. The dedicated management NIC does not link, the other two ports do make link.
What do you suggest to put an IP to CIMC and start installing our applications?
regards

You may have noticed that there is no DVD rom on the c220. What you need to do is:
Login into the CIMC from your browser
Luanch the KVM
Insert the VMware DVD in your machines drive
On the KVM pop up there should be a tab to mount the drive, after mounting it click on Macros and choose ctrl_alt+delete to restart.
After the VMware OS installs press F2 to enter IP.
Browse to the VMware ip to download the Vsphere client
Open the Vsphere client, enter the ip of the vmware and the username will be root and no password if you did not set one.
You can now upload OVA templates or manually create virtua machine from this enviroment.
Hope this help

Can I get rid of Exchange with the new Server just released?

Hi, I saw the new 8 core machine and all the programs. I also recieved an email from Apple telling me about all the calendaring it has.
I want to get rid of Exchange. I have Outlook on 99.9% the clients, however, and they're not going to get rid of Windows or Office any time soon. Will the new server just released and the server software do Exchange server calendaring, scheduling, etc. just like (or better) than Exchange does?
Thanks.

iCalServer uses the new standard CalDAV protocol for calendaring. Exchange uses MS's own proprietary protocols - we do not have those implemented in iCalServer. As a result your existing Outlook users can't use iCalServer right now.
The good news is that there is at least one group working on a plugin for Outlook that will enable access to iCalServer. Whilst this is still alpha quality right now progress is being made, and hopefully in the near future thee will be something usable. See <http://openconnector.org>.

Why index creation is slower on the new server?

Hi there,
Here is a bit of background/env info:
Existing prod server (physical): Oracle 10gR2 10.2.0.5.8 on ASM
RAM: 96GB
CPUs: 8
RHEL 5.8 64bit
Database size around 2TB
New server:
VMWare VM with Oracle 10gR2 10.2.0.5.8 on ASM
RAM 128GB
vCPUs: 16
RHEL 5.8 64bit
Copy of prod DB (from above server) - all init param are the same
I noticed that Index creation is slower on this server. I ran following query:
SELECT name c1, cnt c2, DECODE (total, 0, 0, ROUND (cnt * 100 / total)) c3
FROM (SELECT name, VALUE cnt, (SUM (VALUE) OVER ()) total
FROM v$sysstat
WHERE name LIKE 'workarea exec%')
C1
C2
C3
workarea executions - optimal
100427285
100
workarea executions - onepass
2427
0
workarea executions - multipass
0
0
Following bitmap index takes around 40mins in prod server while it takes around 2Hrs on the VM.
CREATE BITMAP INDEX MY_IDX ON
MY_HIST(PROD_YN) TABLESPACE TS_IDX PCTFREE 10
STORAGE(INITIAL 12582912 NEXT 12582912 PCTINCREASE 0 ) NOLOGGING
This index is created during a batch-process and the dev team is complaining of slowness of the batch on new server. I have found this one statement responsible for some of the grief. There may be more and I am investigating.
I know that adding "parallel" option may speedup but I want find out why is it slow on the new server.
I tried creating a simple index on a large table and it took 2min in prod and 3.5min on this VM. So I guess index creation is slower on this VM in general. DMLs (select/insert/delete/update) seem to work with better elapsed time.
Any clues what might be causing this slowness in index creation?
Best regards

I have been told that the SAN in use by the VM has capacity of 10K IOPS. Not sure of this info helps. I don't know more than this about the storage.
What else do I need to find out? Please let me know - I'll check with my Sys Admin and update the thread.
Best regards

Move database to the new server

Hello,
I have 10.2.0.1 Standard Edition database (7GB, not in archivelog mode) on Windows2003 server, and need to move it to the new server (same environment). I thought to use OEM Clone option, but it appears cloning to the other host is working only in Grid - and I have DB Control.
I know about manual cloning/recreation, but now looking into export and import option. So I think to install Oracle database on the new server, then import some relevant tablespaces exported from the old database. I will use datapump utility in OEM, under system username.
Is that a good approach ? What rules should be applied to avoid problems in that case ? Sorry if it's very basic question, never moved database before.
Marina

Options for porting the database from one server to another after installing Oracle on the new server incldue
Export/Import using expdp/impdp
Rman duplicate to compatiable hardware
Rman file conversion to non-compatiable hardware
On advantage of expdp/impdp is this option supports reconfiguring the database tablespace/file/object storage layout as part of the migration. Also the adoption of new features like ASSM.
A disadvantage is that using expdp/impdp will probably be slower and involve more DBA work than using file copies via rman. There are approaches to reduce the clock time necessary to support export/import and the work is often beneficial for long-term database management efforts.
There have been threads on this topic before and failry recently. You might want to hunt one or two of them down.
HTH -- Mark D Powell --

Exch2k7 to Exch2k10 - SSL 'request' help for the new server

Hi,
after read the article 'http://technet.microsoft.com/en-us/library/dd638158.aspx', we already have MBX and CAS 2007 running the lastest spk version and the SSL on the CAS 2007 is already working as 'LEGACY.DOMAIN.COM.BR' + 'Autodiscover.domain.com.br'
+ 'mail.domain.com.br'.
My question is regarding the SSL request for the new server:
>>> Can I start the REQUEST for the external Certification Authority using Windows Powershell or IIS console instead to use 'Exchange Management Shell'??
* I´m afraid about the time (days) to install CAS 2010 on the new server, start the request to the CA, do the internal steps to aprove, pay the tax, wait for generation and then install the new SSL on the new server...

Hi,
Based on my research, we can use IIS renew the certificate for IIS:
http://support.microsoft.com/kb/228991
And Windows power shell can help us to create certificate request:
http://social.technet.microsoft.com/Forums/exchange/en-US/1ba38a64-8776-444c-9f4d-a484075f3de2/powershell-to-request-a-certificate-renewal
Thanks,
Angela Shi
TechNet Community Support

HT4623 i'm updating my iphone 3gs but i get to the activation point and it tells me the activation server is temporarily unavailable and i keep trying .i'm worried to loose some of the memo

i'm updating my iphone 3gs but i get to the activation point and it tells me the activation server is temporarily unavailable and i keep trying .i'm worried to loose some of the memo? please advice

That's almost always because the phone was hacked or jailbroken to unlock it.

FRM-92101 There was a failure in the forms server during startup

Hi guys when running EBS i am getting this error:
it happens when i try to load any form i.e hrms managemnet --> work structure -> organization
error : FRM-92101 There was a failure in the forms server during startup
this could happen due to invalid configuration
please look into webserver log file for detail
following are the formsweb.cfg file details:
-------------------------------------------------------------------------------start----------------------------------------
[oratest@kapp server]$ vi formsweb.cfg
[oratest@kapp server]$ tail -1000 formsweb.cfg
# $Id: formsweb.cfg 15-apr-2005.13:17:30 pkuhn Exp $
# formsweb.cfg defines parameter values used by the FormsServlet (frmservlet)
# This section defines the Default settings. Any of them may be overridden in the
# following Named Configuration sections. If they are not overridden, then the
# values here will be used.
# The default settings comprise two types of parameters: System parameters,
# which cannot be overridden in the URL, and User Parameters, which can.
# Parameters which are not marked as System parameters are User parameters.
# SYSTEM PARAMETERS
# These have fixed names and give information required by the Forms
# Servlet in order to function. They cannot be specified in the URL query
# string. But they can be overridden in a named configuration (see below).
# Some parameters specify file names: if the full path is not given,
# they are assumed to be in the same directory as this file. If a path
# is given, then it should be a physical path, not a URL.
# USER PARAMETERS
# These match variables (e.g. %form%) in the baseHTML file. Their values
# may be overridden by specifying them in the URL query string
# (e.g. "http://myhost.mydomain.com/forms/frmservlet?form=myform&width=700")
# or by overriding them in a specific, named configuration (see below)
[default]
# System parameter: default base HTML file
baseHTML=base.htm
# System parameter: base HTML file for use with JInitiator client
baseHTMLjinitiator=basejini.htm
# System parameter: base HTML file for use with Sun's Java Plug-In
baseHTMLjpi=basejpi.htm
# System parameter: delimiter for parameters in the base HTML files
HTMLdelimiter=%
# System parameter: working directory for Forms runtime processes
# WorkingDirectory defaults to <oracle_home>/forms if unset.
workingDirectory=
# System parameter: file setting environment variables for the Forms runtime processes
envFile=default.env
# Forms runtime argument: whether to escape certain special characters
# in values extracted from the URL for other runtime arguments
escapeparams=true
# Forms runtime argument: which form module to run
form=test.fmx
# Forms runtime argument: database connection details
userid=
# Forms runtime argument: whether to run in debug mode
debug=no
# Forms runtime argument: host for debugging
host=
# Forms runtime argument: port for debugging
port=
# Other Forms runtime arguments: grouped together as one parameter.
# These settings support running and debugging a form from the Builder:
otherparams=buffer_records=%buffer% debug_messages=%debug_messages% array=%array% obr=%obr% query_only=%query_only% quiet=%quiet% render=%render% record=%record% tracegroup=%tracegroup% log=%log% term=%term%
# Sub argument for otherparams
buffer=no
# Sub argument for otherparams
debug_messages=no
# Sub argument for otherparams
array=no
# Sub argument for otherparams
obr=no
# Sub argument for otherparams
query_only=no
# Sub argument for otherparams
quiet=yes
# Sub argument for otherparams
render=no
# Sub argument for otherparams
record=
# Sub argument for otherparams
tracegroup=
# Sub argument for otherparams
log=
# Sub argument for otherparams
term=
# HTML page title
pageTitle=Oracle Application Server Forms Services
# HTML attributes for the BODY tag
HTMLbodyAttrs=
# HTML to add before the form
HTMLbeforeForm=
# HTML to add after the form
HTMLafterForm=
# Forms applet parameter: URL path to Forms ListenerServlet
serverURL=/forms/lservlet
# Forms applet parameter
codebase=/forms/java
# Forms applet parameter
imageBase=DocumentBase
# Forms applet parameter
width=750
# Forms applet parameter
height=600
# Forms applet parameter
separateFrame=false
# Forms applet parameter
splashScreen=
# Forms applet parameter
background=
# Forms applet parameter
lookAndFeel=Oracle
# Forms applet parameter
colorScheme=teal
# Forms applet parameter
logo=
# Forms applet parameter
restrictedURLparams=HTMLbodyAttrs,HTMLbeforeForm,pageTitle,HTMLafterForm,log,allow_debug,allowNewConnections
# Forms applet parameter
formsMessageListener=
# Forms applet parameter
recordFileName=
# Forms applet parameter
serverApp=default
# Forms applet archive setting for JInitiator
archive_jini=frmall_jinit.jar
# Forms applet archive setting for other clients (Sun Java Plugin, Appletviewer, etc)
archive=frmall.jar
# Number of times client should retry if a network failure occurs. You should
# only change this after reading the documentation.
networkRetries=0
# Page displayed to Netscape users to allow them to download Oracle JInitiator.
# Oracle JInitiator is used with Windows clients.
# If you create your own page, you should set this parameter to point to it.
jinit_download_page=/forms/jinitiator/us/jinit_download.htm
# Parameter related to the version of JInitiator
jinit_classid=clsid:CAFECAFE-0013-0001-0022-ABCDEFABCDEF
# Parameter related to the version of JInitiator
jinit_exename=jinit.exe#Version=1,3,1,22
# Parameter related to the version of JInitiator
jinit_mimetype=application/x-jinit-applet;version=1.3.1.22
# Page displayed to users to allow them to download Sun's Java Plugin.
# Sun's Java Plugin is typically used for non-Windows clients.
# (NOTE: you should check this page and possibly change the settings)
jpi_download_page=http://java.sun.com/products/archive/j2se/1.4.2_06/index.html
# Parameter related to the version of the Java Plugin
jpi_classid=clsid:CAFEEFAC-0014-0002-0006-ABCDEFFEDCBA
# Parameter related to the version of the Java Plugin
jpi_codebase=http://java.sun.com/products/plugin/autodl/jinstall-1_4_2-windows-i586.cab#Version=1,4,2,06
# Parameter related to the version of the Java Plugin
jpi_mimetype=application/x-java-applet;jpi-version=1.4.2_06
# EM config parameter
# Set this to "1" to enable Enterprise Manager to track Forms processes
em_mode=0
# Single Sign-On OID configuration parameter
oid_formsid=%OID_FORMSID%
# Single Sign-On OID configuration parameter
oracle_home=/mnt/extdrive/VIS/apps/tech_st/10.1.2/
# Single Sign-On OID configuration parameter
formsid_group_dn=%GROUP_DN%
# Single Sign-On OID configuration parameter: indicates whether we allow
# dynamic resource creation if the resource is not yet created in the OID.
ssoDynamicResourceCreate=true
# Single Sign-On parameter: URL to redirect to if ssoDynamicResourceCreate=false
ssoErrorUrl=
# Single Sign-On parameter: Cancel URL for the dynamic resource creation DAS page.
ssoCancelUrl=
# Single Sign-On parameter: indicates whether the url is protected in which
# case mod_osso will be given control for authentication or continue in
# the FormsServlet if not. It is false by default. Set it to true in an
# application-specific section to enable Single Sign-On for that application.
ssoMode=false
# The parameter allow_debug determines whether debugging is permitted.
# Administrators should set allow_debug to "true" if servlet
# debugging is required, or to provide access to the Forms Trace Xlate utility.
# Otherwise these activities will not be allowed (for security reasons).
allow_debug=false
# Parameter which determines whether new Forms sessions are allowed.
# This is also read by the Forms EM Overview page to show the
# current Forms status.
allowNewConnections=true
# EndUserMonitoring
# EndUserMonitoringEnabled parameter
# Indicates whether EUM/Chronos integration is enabled
EndUserMonitoringEnabled=
# EndUserMonitoringURL
# indicates where to record EUM/Chronos data
EndUserMonitoringURL=
# Example Named Configuration Section
# Example 1: configuration to run forms in a separate browser window with
# "generic" look and feel (include "config=sepwin" in the URL)
# You may define your own specific, named configurations (sets of parameters)
# by adding special sections as illustrated in the following examples.
# Note that you need only specify the parameters you want to change. The
# default values (defined above) will be used for all other parameters.
# Use of a specific configuration can be requested by including the text
# "config=<your_config_name>" in the query string of the URL used to run
# a form. For example, to use the sepwin configuration, your could issue
# a URL like "http://myhost.mydomain.com/forms/frmservlet?config=sepwin".
[sepwin]
separateFrame=True
lookandfeel=Generic
# Example Named Configuration Section
# Example 2: configuration forcing use of the Java Plugin in all cases (even if
# the client browser is on Windows)
[jpi]
baseHTMLJInitiator=basejpi.htm
# Example Named Configuration Section
# Example 3: configuration running the Forms ListenerServlet in debug mode
# (debug messages will be written to the servlet engine's log file).
[debug]
serverURL=/forms/lservlet/debug
# Sample configuration for deploying WebUtil. Note that WebUtil is shipped with
# DS but not AS and is also available for download from OTN.
[webutil]
WebUtilArchive=frmwebutil.jar,jacob.jar
WebUtilLogging=off
WebUtilLoggingDetail=normal
WebUtilErrorMode=Alert
WebUtilDispatchMonitorInterval=5
WebUtilTrustInternal=true
WebUtilMaxTransferSize=16384
baseHTMLjinitiator=webutiljini.htm
baseHTMLjpi=webutiljpi.htm
archive_jini=frmall_jinit.jar
archive=frmall.jar
lookAndFeel=orac
------------------------------------------------------end----------------------------------------------
plz help
regards,
kashif

Hi Hussein,
i got the error in application log that libXm.so.2 is missing, then i installed openmotif to resolve it, but after that form window is not opening.
and application log is as follows:
10/10/22 18:41:45.258 10.1.3.0.0 Started
10/10/22 18:41:46.981 formsweb: FormsServlet init():
configFileName: /mnt/extdrive/VIS/inst/apps/VIS_kapp/ora/10.1.2/forms/server/appsweb.cfg
testMode: false
10/10/22 18:41:46.993 formsweb: 10.1.3.0.0 Started
10/10/22 18:44:38.873 formsweb: ListenerServlet init()
10/10/22 18:44:40.204 formsweb: Forms session <1> failed during startup: no response from runtime process
10/10/22 18:44:40.206 formsweb: Forms session <1> exception stack trace:
oracle.forms.engine.RunformException: Forms session <1> failed during startup: no response from runtime process
at oracle.forms.servlet.RunformProcess.connect(Unknown Source)
at oracle.forms.servlet.RunformProcess.dataToRunform(Unknown Source)
at oracle.forms.servlet.RunformSession.dataToRunform(Unknown Source)
at oracle.forms.servlet.ListenerServlet.doPost(Unknown Source)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:763)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:856)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:719)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:376)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.HttpRequestHandler.doProcessRequest(HttpRequestHandler.java:870)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:451)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.AJPRequestHandler.run(AJPRequestHandler.java:299)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.AJPRequestHandler.run(AJPRequestHandler.java:187)
at oracle.oc4j.network.ServerSocketReadHandler$SafeRunnable.run(ServerSocketReadHandler.java:260)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:303)
at java.lang.Thread.run(Thread.java:595)
10/10/23 14:57:11.795 10.1.3.0.0 Started
10/10/23 14:57:22.415 formsweb: FormsServlet init():
configFileName: /mnt/extdrive/VIS/inst/apps/VIS_kapp/ora/10.1.2/forms/server/appsweb.cfg
testMode: false
10/10/23 14:57:22.641 formsweb: 10.1.3.0.0 Started
10/10/23 15:01:33.111 formsweb: 10.1.3.0.0 Stopped
10/10/23 15:05:56.542 10.1.3.0.0 Started
10/10/23 15:05:58.541 formsweb: FormsServlet init():
configFileName: /mnt/extdrive/VIS/inst/apps/VIS_kapp/ora/10.1.2/forms/server/appsweb.cfg
testMode: false
10/10/23 15:05:58.652 formsweb: 10.1.3.0.0 Started
10/10/23 15:15:29.23 formsweb: Servlet error
java.io.IOException: Broken pipe
at sun.nio.ch.FileDispatcher.write0(Native Method)
at sun.nio.ch.SocketDispatcher.write(SocketDispatcher.java:29)
at sun.nio.ch.IOUtil.writeFromNativeBuffer(IOUtil.java:104)
at sun.nio.ch.IOUtil.write(IOUtil.java:75)
at sun.nio.ch.SocketChannelImpl.write(SocketChannelImpl.java:302)
at java.nio.channels.Channels.write(Channels.java:60)
at java.nio.channels.Channels.access$000(Channels.java:47)
at java.nio.channels.Channels$1.write(Channels.java:134)
at com.evermind.server.http.AJPOutputStream.endRequest(AJPOutputStream.java:117)
at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:306)
at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:187)
at oracle.oc4j.network.ServerSocketReadHandler$SafeRunnable.run(ServerSocketReadHandler.java:260)
at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:303)
at java.lang.Thread.run(Thread.java:595)
10/10/23 15:32:28.558 formsweb: 10.1.3.0.0 Stopped
10/10/23 15:33:44.992 10.1.3.0.0 Started
10/10/23 15:33:46.570 formsweb: FormsServlet init():
configFileName: /mnt/extdrive/VIS/inst/apps/VIS_kapp/ora/10.1.2/forms/server/appsweb.cfg
testMode: false
10/10/23 15:33:46.610 formsweb: 10.1.3.0.0 Started
regards,
kashif

FRM-92101- There is a failure in the form server during startup.

Hi,
I'm deploying a forms 10g application . I'm using Oracle Application Server Forms and Reports Services 10.1.2.0.2 under Red Hat Enterprise Linux 5, along with an Oracle 10g Database on another server. Every time I try testing the form services using http://10.0.4.114:7778/forms/frmservlet it brings out the errorFRM-92101- There is a failure in the form server during startup. This could happen due to invalid configuration. Please look into the web server log file for detail
Right now, I'm a bit lost. Can anyone please tell me if there is some parameter I have to set, or something I should do to make it work?
Thanks a lot

Fabian,
I did not make changes to those files. The forms services are working on another server with Red hat Rel 4 and 3 . What I did is to configure a new server with Red Hat Rel 5 , took the backup of all the forms binaries and the HOME and restore on the new server. I did the same thing for a server running rel 4 and it has no issue:
The content of the files are as below:
DEFAULT.ENV*
# $Id: default.env 26-apr-2005.16:59:08 sujain Exp $
# default.env - default Forms environment file, Solaris version
# This file is used to set the Forms runtime environment parameters.
# If a parameter is not defined here, the value used will be that defined
# in the environment in which the servlet engine (OC4J or JServ) was started.
# NOTES
# 1/ The Forms installation process should replace all occurrences of
# <percent>FORMS_ORACLE_HOME<percent> with the correct ORACLE_HOME
# setting, and all occurrences of <percent>O_JDK_HOME<percent> with
# the location of the JDK (usually $ORACLE_HOME/jdk).
# Please make these changes manually if not.
# 2/ Some of the variables below may need to be changed to suite your needs.
# Please refer to the Forms documentation for details.
ORACLE_HOME=/u01/oracle10g_Forms
FORMS_PATH=/u/oracle/bank/gmx
REPORTS_PATH=/u/oracle/bank/fonts
#TWO_TASK=rac.world4
TWO_TASK=server.world
#TWO_TASK=server1.world
#TWO_TASK=s0999001.world4
#TWO_TASK=s0202001.world4
#TWO_TASK=server.world4
NLS_LANG=AMERICAN_AMERICA.AR8MSWIN1256
NLS_DATE_FORMAT=DDMMYYYY
# Search path for Forms applications (.fmx files, PL/SQL libraries)
# FORMS_PATH=/u01/oracle10g_Forms/forms
# webutil config file path
WEBUTIL_CONFIG=/u01/oracle10g_Forms/forms/server/webutil.cfg
# Disable/remove this variable if end-users need access to the query-where
# functionality which potentially allows them to enter arbitrary SQL
# statements when in enter-query mode.
FORMS_RESTRICT_ENTER_QUERY=TRUE
# Java class path
# This is required for the Forms debugger
# You can append your own Java code here)
# frmsrv.jar, repository.jar and ldapjclnt10.jar are required for
# the password expiry feature to work(#2213140).
CLASSPATH=/u01/oracle10g_Forms/j2ee/OC4J_BI_Forms/applications/formsapp/formsweb/WEB-INF/lib/frmsrv.jar:/u01/oracle10g_Forms/jlib/repository.jar:/u01/oracle10g_Forms/jlib/ldapjclnt10.jar:/u01/oracle10g_Forms/jlib/debugger.jar:/u01/oracle10g_Forms/jlib/ewt3.jar:/u01/oracle10g_Forms/jlib/share.jar:/u01/oracle10g_Forms/jlib/utj.jar:/u01/oracle10g_Forms/jlib/zrclient.jar:/u01/oracle10g_Forms/reports/jlib/rwrun.jar:/u01/oracle10g_Forms/forms/java/frmwebutil.jar:/u01/oracle10g_Forms/forms/java/frmrwinteg.jar:/u01/oracle10g_Forms/forms/java/webutil.jar
# The PATH setting is not required for Forms if the Forms executables are
# in <ORACLE_HOME>/bin. However, it is required if Graphics applications
# are called from Forms applications.
PATH=/usr/bin:/sbin:/bin:/u01/oracle10g_Forms/bin
# Settings for Reports
# NOTE: This setting is only needed if Reports applications
# are called from Forms applications
# However, because of bug 2336698 where a report is started from
# a forms debugger session with an already running JVM, then
# the report's class path should also be included in the forms
# class path.
# We no longer need to set REPORTS_CLASSPATH as forms will
# always start the JVM before calling reports.
# Settings for Graphics
# NOTE: These settings are only needed if Graphics applications
# are called from Forms applications
# Please uncomment the following and put the correct 6i
# oracle_home value to use Graphics applications.
#ORACLE_GRAPHICS6I_HOME=<your Graphics 6i oracle_home here>
# Search path for Graphics applications
GRAPHICS60_PATH=
# Settings for Forms tracing and logging
# Note: This entry has to be uncommented to enable tracing and
# logging.
#FORMS_TRACE_PATH=<FORMS_ORACLE_HOME>/forms/server
# System settings
# You should not normally need to modify these settings
# Path for shared library objects
# This is highly platform (if not machine) specific ! At install time
# <percent>LD_LIBRARY_PATH<percent> should be replaced with the
# actual value of the LD_LIBRARY_PATH environment variable (at install
# time). That should ensure we have the paths for such necessities as
# the motif and X11 libraries.
# Explanations:
# - Reports needs the path for libjava.so
# (.../jre/lib/sparc)
# - Forms needs two paths to the jre, for libjvm.so and libhpi.so
# - In JDK 1.4.1 the location of libjvm.so is lib/sparc (there is no
# classic directory) so we do not include the .../classic directory
# below. There are other versions of libjvm.so (in directories server,
# client and hotspot) but we will use the version in lib/sparc for now.
LD_LIBRARY_PATH=/u01/oracle10g_Forms/lib:/u01/oracle10g_Forms/jdk/jre/lib/i386:/u01/oracle10g_Forms/jdk/jre/lib/i386/server:/u01/oracle10g_Forms/jdk/jre/lib/i386/native_threads:/u01/oracle10g_Forms/inventory/filemap/jre/1.4.2/lib/i386/client:/u01/oracle10g_Forms/inventory/filemap/jre/1.4.2/lib/i386:/usr/lib:/u01/oracle10g_Forms/jdk/jre/lib/i386/server:/u01/oracle10g_Forms/jdk/jre/lib/i386/native_threads:/u01/oracle10g_Forms/jdk/jre/lib/i386:/u01/oracle10g_Forms/jdk/jre/lib/i386:/usr/lib:/u01/oracle10g_Forms/lib:/u01/oracle10g_Forms/classes/lib:/u01/oracle10g_Forms/ifs1.1/lib:/u01/oracle10g_Forms/jis/lib
LD_ASSUME_KERNEL=2.4.19
FORMSWEB*
# $Id: formsweb.cfg 15-apr-2005.13:17:30 pkuhn Exp $
# formsweb.cfg defines parameter values used by the FormsServlet (frmservlet)
# This section defines the Default settings. Any of them may be overridden in the
# following Named Configuration sections. If they are not overridden, then the
# values here will be used.
# The default settings comprise two types of parameters: System parameters,
# which cannot be overridden in the URL, and User Parameters, which can.
# Parameters which are not marked as System parameters are User parameters.
# SYSTEM PARAMETERS
# These have fixed names and give information required by the Forms
# Servlet in order to function. They cannot be specified in the URL query
# string. But they can be overridden in a named configuration (see below).
# Some parameters specify file names: if the full path is not given,
# they are assumed to be in the same directory as this file. If a path
# is given, then it should be a physical path, not a URL.
# USER PARAMETERS
# These match variables (e.g. %form%) in the baseHTML file. Their values
# may be overridden by specifying them in the URL query string
# (e.g. "http://myhost.mydomain.com/forms/frmservlet?form=myform&width=700")
# or by overriding them in a specific, named configuration (see below)
[default]
# System parameter: default base HTML file
baseHTML=base.htm
# System parameter: base HTML file for use with JInitiator client
baseHTMLjinitiator=basejini.htm
# System parameter: base HTML file for use with Sun's Java Plug-In
baseHTMLjpi=basejpi.htm
# System parameter: delimiter for parameters in the base HTML files
HTMLdelimiter=%
# System parameter: working directory for Forms runtime processes
# WorkingDirectory defaults to <oracle_home>/forms if unset.
workingDirectory=
# System parameter: file setting environment variables for the Forms runtime processes
envFile=default.env
# Forms runtime argument: whether to escape certain special characters
# in values extracted from the URL for other runtime arguments
escapeparams=true
# Forms runtime argument: which form module to run
#form=test.fmx
form=B08SSS20.fmx
# Forms runtime argument: database connection details
userid=guiusr/guiusr
# Forms runtime argument: whether to run in debug mode
debug=no
# Forms runtime argument: host for debugging
host=
# Forms runtime argument: port for debugging
port=
# Other Forms runtime arguments: grouped together as one parameter.
# These settings support running and debugging a form from the Builder:
otherparams=buffer_records=%buffer% debug_messages=%debug_messages% array=%array% obr=%obr% query_only=%query_only% quiet=%quiet% render=%render% record=%record% tracegroup=%tracegroup% log=%log% term=%term%
# Sub argument for otherparams
buffer=no
# Sub argument for otherparams
debug_messages=no
# Sub argument for otherparams
array=no
# Sub argument for otherparams
obr=no
# Sub argument for otherparams
query_only=no
# Sub argument for otherparams
quiet=yes
# Sub argument for otherparams
render=no
# Sub argument for otherparams
record=
# Sub argument for otherparams
tracegroup=
# Sub argument for otherparams
log=
# Sub argument for otherparams
term=
# HTML page title
pageTitle=Oracle Application Server Forms Services
# HTML attributes for the BODY tag
HTMLbodyAttrs=
# HTML to add before the form
HTMLbeforeForm=
# HTML to add after the form
HTMLafterForm=
# Forms applet parameter: URL path to Forms ListenerServlet
serverURL=/forms/lservlet
# Forms applet parameter
codebase=/forms/java
# Forms applet parameter
imageBase=DocumentBase
# Forms applet parameter
width=900
# Forms applet parameter
height=800
# Forms applet parameter
separateFrame=true
# Forms applet parameter
splashScreen=no
# Forms applet parameter
background=no
# Forms applet parameter
lookAndFeel=Oracle
# Forms applet parameter
colorScheme=blue
# Forms applet parameter
logo=no
# Forms applet parameter
restrictedURLparams=HTMLbodyAttrs,HTMLbeforeForm,pageTitle,HTMLafterForm,log,allow_debug,allowNewConnections
# Forms applet parameter
formsMessageListener=
# Forms applet parameter
recordFileName=
# Forms applet parameter
serverApp=default
# Forms applet archive setting for JInitiator
archive_jini=frmall_jinit.jar,timeout.jar,frmrwinteg.jar,webutil.jar
# Forms applet archive setting for other clients (Sun Java Plugin, Appletviewer, etc)
archive=frmall.jar
# Number of times client should retry if a network failure occurs. You should
# only change this after reading the documentation.
networkRetries=30
# Page displayed to Netscape users to allow them to download Oracle JInitiator.
# Oracle JInitiator is used with Windows clients.
# If you create your own page, you should set this parameter to point to it.
jinit_download_page=/forms/jinitiator/us/jinit_download.htm
# Parameter related to the version of JInitiator
jinit_classid=clsid:CAFECAFE-0013-0001-0022-ABCDEFABCDEF
# Parameter related to the version of JInitiator
jinit_exename=jinit.exe#Version=1,3,1,22
# Parameter related to the version of JInitiator
jinit_mimetype=application/x-jinit-applet;version=1.3.1.22
# Page displayed to users to allow them to download Sun's Java Plugin.
# Sun's Java Plugin is typically used for non-Windows clients.
# (NOTE: you should check this page and possibly change the settings)
jpi_download_page=http://java.sun.com/products/archive/j2se/1.4.2_06/index.html
# Parameter related to the version of the Java Plugin
jpi_classid=clsid:CAFEEFAC-0014-0002-0006-ABCDEFFEDCBA
# Parameter related to the version of the Java Plugin
jpi_codebase=http://java.sun.com/products/plugin/autodl/jinstall-1_4_2-windows-i586.cab#Version=1,4,2,06
# Parameter related to the version of the Java Plugin
jpi_mimetype=application/x-java-applet;jpi-version=1.4.2_06
# EM config parameter
# Set this to "1" to enable Enterprise Manager to track Forms processes
em_mode=1
# Single Sign-On OID configuration parameter
oid_formsid=%OID_FORMSID%
# Single Sign-On OID configuration parameter
oracle_home=/u01/oracle10g_Forms
# Single Sign-On OID configuration parameter
formsid_group_dn=%GROUP_DN%
# Single Sign-On OID configuration parameter: indicates whether we allow
# dynamic resource creation if the resource is not yet created in the OID.
ssoDynamicResourceCreate=true
# Single Sign-On parameter: URL to redirect to if ssoDynamicResourceCreate=false
ssoErrorUrl=
# Single Sign-On parameter: Cancel URL for the dynamic resource creation DAS page.
ssoCancelUrl=
# Single Sign-On parameter: indicates whether the url is protected in which
# case mod_osso will be given control for authentication or continue in
# the FormsServlet if not. It is false by default. Set it to true in an
# application-specific section to enable Single Sign-On for that application.
ssoMode=false
# The parameter allow_debug determines whether debugging is permitted.
# Administrators should set allow_debug to "true" if servlet
# debugging is required, or to provide access to the Forms Trace Xlate utility.
# Otherwise these activities will not be allowed (for security reasons).
allow_debug=true
# Parameter which determines whether new Forms sessions are allowed.
# This is also read by the Forms EM Overview page to show the
# current Forms status.
allowNewConnections=true
# EndUserMonitoring
# EndUserMonitoringEnabled parameter
# Indicates whether EUM/Chronos integration is enabled
EndUserMonitoringEnabled=
# EndUserMonitoringURL
# indicates where to record EUM/Chronos data
EndUserMonitoringURL=
# Example Named Configuration Section
# Example 1: configuration to run forms in a separate browser window with
# "generic" look and feel (include "config=sepwin" in the URL)
# You may define your own specific, named configurations (sets of parameters)
# by adding special sections as illustrated in the following examples.
# Note that you need only specify the parameters you want to change. The
# default values (defined above) will be used for all other parameters.
# Use of a specific configuration can be requested by including the text
# "config=<your_config_name>" in the query string of the URL used to run
# a form. For example, to use the sepwin configuration, your could issue
# a URL like "http://myhost.mydomain.com/forms/frmservlet?config=sepwin".
[sepwin]
separateFrame=True
lookandfeel=Generic
# Example Named Configuration Section
# Example 2: configuration forcing use of the Java Plugin in all cases (even if
# the client browser is on Windows)
[jpi]
baseHTMLJInitiator=basejpi.htm
# Example Named Configuration Section
# Example 3: configuration running the Forms ListenerServlet in debug mode
# (debug messages will be written to the servlet engine's log file).
[debug]
serverURL=/forms/lservlet/debug
# Sample configuration for deploying WebUtil. Note that WebUtil is shipped with
# DS but not AS and is also available for download from OTN.
[webutil]
WebUtilArchive=frmwebutil.jar,jacob.jar
WebUtilLogging=off
WebUtilLoggingDetail=normal
WebUtilErrorMode=Alert
WebUtilDispatchMonitorInterval=5
WebUtilTrustInternal=true
WebUtilMaxTransferSize=16384
baseHTMLjinitiator=webutiljini.htm
baseHTMLjpi=webutiljpi.htm
archive_jini=frmall_jinit.jar
archive=frmall.jar
lookAndFeel=oracle
[ref]
#serverURL=/forms/lservlet/perf
serverURL=/forms/lservlet/
#otherparams=P_WST_LAN_IND=1 record=forms tracegroup=0-199
#envFile=default.env
[nat]
#serverURL=/forms/lservlet/perf
serverURL=/forms/lservlet/sessionperf
#envFile=defaultar.env
ERROR IN Java console is
Oracle JInitiator: Version 1.3.1.22
Using JRE version 1.3.1.22-internal Java HotSpot(TM) Client VM
User home directory = C:\Documents and Settings\akintayo.beckley.GTBANK
c: clear console window
f: finalize objects on finalization queue
g: garbage collect
h: display this help message
l: dump classloader list
m: print memory usage
q: hide console
s: dump system properties
t: dump thread list
x: clear classloader cache
0-5: set trace level to <n>
proxyHost=null
proxyPort=0
connectMode=HTTP, native.
oracle.forms.net.ConnectionException: Forms session <1> failed during
startup: no response from runtime process
at
oracle.forms.net.ConnectionException.createConnectionException(Unknown
Source)
at oracle.forms.net.HTTPNStream.getResponse(Unknown Source)
at oracle.forms.net.HTTPNStream.doFlush(Unknown Source)
at oracle.forms.net.HTTPNStream.flush(Unknown Source)
at java.io.DataOutputStream.flush(Unknown Source)
at oracle.forms.net.HTTPConnection.connect(Unknown Source)
at oracle.forms.engine.FormsDispatcher.initConnection(Unknown Source)
at oracle.forms.engine.FormsDispatcher.init(Unknown Source)
at oracle.forms.engine.Runform.initConnection(Unknown Source)
at oracle.forms.engine.Runform.startRunform(Unknown Source)
at oracle.forms.engine.Main.createRunform(Unknown Source)
at oracle.forms.engine.Main.start(Unknown Source)
at sun.applet.AppletPanel.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)

FRM-92101: failure in the Forms Server during startup.

Hi
I am calling a Oracle report from a Oracle forms application. When I enter the parameters on the Parameter Form (Oracle Forms Application created for
entering the User Parameters) and click 'Run Report' button, I am getting the following error:
Kindly help me on this. Thanks in advance.
The complete error discription is given here...
FRM-92101: There was a failure in the Forms Server during startup. This could happen due to invalid configuration.
Details...
Java Exception:
oracle.forms.net.ConnectionException: Forms session <3> aborted: unable to communicate with runtime process.
- at oracle.forms.net.ConnectionException.createConnectionException(Unknown Source)
- at oracle.forms.net.HTTPNStream.getResponse(Unknown Source)
- at oracle.forms.net.HTTPNStream.doFlush(Unknown Source)
- at oracle.forms.net.HTTPNStream.flush(Unknown Source)
- at java.io.DataOutputStream.flush(Unknown Source)
- at oracle.forms.net.StreamMessageWritter.run(Unknown Source)
Environment in which my Forms and Report Applications is running:
Operating System     -     Windows XP Professional
Oracle9i Enterprise Edition Release 9.2.0.1.0 - 64bit Production With the Partitioning option
JServer Release 9.2.0.1.0 - Production
Forms [32 Bit] Version 10.1.2.0.2 (Production)
Report Builder 10.1.2.0.2
ORACLE Server Release 10.1.0.4.2
Please find the steps I followed before I run this application:
1. I started the OC4J Forms Server on my machine
2. I started the OracleAS Reports Services (Reports Server) on my machine.
3. Connected to the database and run the Forms Application.
I have tried the following options to solve this error:
- I have re-installed Oracle Enterprise Edition Release 9.2.0.1.0 again and retry calling my Reports application from Oracle Forms. Still the same error
persists.
I have written the following code inside 'WHEN-BUTTON-PRESSED' Trigger to call my Oracle Report:
I found that the above error is coming at the following highlighted line below:
declare
BEGIN
     --prepare the list of parameters to be sent to the report
     --Add parameter(s) to list just created
     --START THE REPORT
     v_repid := FIND_REPORT_OBJECT('REPORT197');
     vc_rep := RUN_REPORT_OBJECT(v_repid, Plist);
     --GET REPORT STATUS
     vc_rep_status := REPORT_OBJECT_STATUS(vc_rep);
     -- Wait until report finishes or produces an error
     -- Display the report if it is finished
END;

Hi ,
I think that this kind of problem persists because of the variety of Forms , Database and maybe OS number-bit versions(32-bit and 64 respectively).
In the past , due to the inequality of number-bit of OS and the Oracle Products , I had many problems.... the import was finished abnormally as the connection to the database was stopped ...
Regards,
Simon

FRM-92101: There was a failure in the Forms Server during startup.This coul

HI,
HI to everyone, we are currently working oracle apps 12i custom module, our forms and reports are done completely in Forms/Reports database 10g. we are trying to run the reports using forms in apps(why it has got another history). cut the story short we are calling reports from Forms and we will call the forms in apps
the following code which i have used in 'WHEN-BUTTON-PRESSD'
message('report START.');
DECLARE
repid REPORT_OBJECT;
v_rep VARCHAR2(100);
rep_status varchar2(20);
rep_url varchar2(2000);
BEGIN
repid := find_report_object('EMP');
message('report FOUND');
v_rep := RUN_REPORT_OBJECT(repid);
message('Run Report Object just FIRED');
rep_status := REPORT_OBJECT_STATUS(v_rep);
if rep_status = 'FINISHED' then
message('Report Completed');
else
message('Error when running report.');
end if;
END;
FRM-92101: There was a failure in the Forms Server during startup. This could happen due to Invalid Configuration
Please look in to the web-server log-file for details.
Details..
Java Exception:
oracle.forms.net.ConnectionException: Forms session <1> aborted: unable to communicate with runtime process.
at oracle.forms.net.ConnectionException.createConnectionException(Unknown Source)
at oracle.forms.net.HTTPNStream.getResponse(Unknown Source)
at oracle.forms.net.HTTPNStream.doFlush(Unknown Source)
at oracle.forms.net.HTTPNStream.flush(Unknown Source)
at java.io.DataOutputStream.flush(Unknown Source)
at oracle.forms.net.StreamMessageWriter.run(Unknown Source)
Thanks..in advance, your help is much appreicated
CS

Please enable Forms Runtime Diagnostics (FRD), and re-produce the issue. Once you are done, post the error you get here. For more details about FRD, please check the following note:
Note: 438652.1 - R12: Forms Runtime Diagnostics (FRD), Tracing And Logging For Forms In Oracle Applications
https://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=438652.1

FRM-92101:There was a failure in the Forms Server during setup

I get the following runtime error when press "send" button in one of the forms.
FRM-92101:There was a failure in the Forms Server during setup. This could happen due to invalid configuration. Please look into the web-server log file for details.
Please suggest how to resolve....

Getting the error "FRM-92101:There was a failure in the Forms Server during setup" when calling a db package from forms package. (Specifically when package variable is defined in record type).
Application.log shows
10/03/06 08:26:06 formsweb: Forms session <54> aborted: unable to communicate with runtime process.
10/03/06 08:26:06 formsweb: Forms session <54> exception stack trace:
java.io.IOException: FRM-93000: Unexpected internal error.
Details : No HTTP headers received from runform
Please let me know the solution............
Other Details:_
Rec type is being used in the forms package and db package.
DB Package (dbpkg1) Spec:_
TYPE rec_type IS RECORD
(var1 IN db.pkg1.var_type, (var_type is table of table1.field5%type)
var2 IN table.field1%TYPE,
var3 IN table.field2%TYPE,
var4 IN table.field2%TYPE,
var5 IN table.field2%TYPE,
var6 BOOLEAN)
PROCEDURE main
(rec1 IN rec_type);
Form body:_
PROCEDURE proc1
IS
frm_rec dbpkg1.rec_type;
BEGIN
frm_rec.var2 = "Value";
frm_rec.var3 = "Value";
frm_rec.var4 = "Value"
frm_rec.var5 = "Value"
frm_rec.var6 = "Value"
dbpkg1.main(frm_rec);

FRM-92101: There was a failure in the Forms Server during startup.R12.1-WXP

Hi All,
I have installed R12.1 on Windows XP Professional.
When I open any form after login the application gives the following error message instead of opening the form:
FRM-92101: There was a failure in the Forms Server during startup. This could happened due to invalid configruation. Please look into the web-server log file for details.
Details...
Java Exception:
oracle.forms.net.ConnectionException: Forms session (6) failed during startup: no response form runtime process
at oracle.forms.net.ConnectionException.createConnectionException(Unknown Source)
at oracle.forms.net.HTTPNStream.getResponse(Unknown Source)
at oracle.forms.net.HTTPNStream.doFlush(Unknown Source)
at oracle.forms.net.HTTPNStream.flush(Unknown Source)
at oracle.forms.net.HTTPNStream.getResponse(Unknown Source)
at java.io.DataOutputStream.flush(Unkown Source)
at oracle.forms.net.HTTPConnection.connet(Unknown Source)
at oracle.forms.engine.FormsDispatcher.initConnection(Unknown Source)
at oracle.forms.egnine.FormsDispatcher.init(Unknown Source)
at oracle.forms.egnine.Runform.initConnection(Unknown Source)
at oracle.forms.egnine.Runform.startRunform(Unknown Source)
at oracle.forms.egnine.Main.createRunform(Unknown Source)
at oracle.forms.egnine.Main.start(Unknown Source)
at sun.applet.AppletPanel.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
please help out to resolve this issue.
Regards,
Fahd

Hi;
XP is not certified platform. Similar issue mention here many times.Please see:
Recommended Browsers for Oracle E-Business Suite Release 12 [ID 389422.1]
FRM-92101: There Was a Failure in the Forms Server During Startup After Fresh R12 Installation [ID 429627.1]
R12 fresh install FORMS DO NOT LAUNCH - FRM-92101/500 [ID 427714.1]
FRM-92101: Forms Server oracle.forms.net.ConnectionException: Forms session <1> failed during startup: no response from runtime process [ID 880088.1]
Forms: 9.x and 10.x: Troubleshooting FRM-92050, FRM-921xx [ID 189867.1]
Known Causes of FRM-92101 Error In Forms [ID 604633.1]
Also check:
http://onlineappsdba.com/index.php/2009/06/15/frm-92101-with-internet-explorer-8-how-to-uninstall-ie8/
Re: R12 database and JRE Issue
FRM-92101 There was a failure in the forms server during startup
Regard
Helios

Safely point an NSS VMDK to the new server during transferID

Similar Messages

Maybe you are looking for