Sagem f@ast 1400, mac mini: extending the range?

In my living room I have a mac mini connected via its inbuilt airport to my sagem fast 1400 wifi router which is sitting about 4 metres away.
My wife wants to use her dodgy dell laptop for internet work etc in the basement together with the printer, but the wi-fi signal does not extend that far.
Questions: If I bought an airport for the basement, could i connect an ethernet from the laptop (6 yrs old, no inbuilt wireless) to the airport to surf, and could i connect a printer to the airport so that both the laptop and mac mini upstairs could print?
I've read the faq, but not being tech savvy, I find it hard to follow.
Thanks,
Blob

No, the Airport Express will not extend the wireless range of the Sagem router.
For the Airport Express ethernet port to be active, and for the Airport Express to wirelessly extend the wireless range of a base station, that base station must support what Apple calls a "wireless distribution system" (WDS). Your Sagem wireless router doesn't support Apple's WDS system.

Similar Messages

  • I have a airport time capsule, an older airport extreme, and an airport express.  I want to hard wire my Mac Mini to the network.  What is the best arrangement of the devices?  which ones should be hard wired to optimize extending the network?

    I have a airport time capsule, an older airport extreme, and an older airport express.  I want to hard wire my Mac Mini to the network.  What is the best arrangement of the devices?  which ones should be hard wired to optimize extending the network?

    I am using TM Unifi with an ASUS RT-N18U Wi-Fi router.  I would like to know could I use Apple AirPort Time Capsule to extend (repeater, booster) my Wi-Fi to a part of the house where the Wi-Fi signal is poor
    Yes,, if you plan to connect the AirPort Time Capsule to the ASUS router using an Ethernet cable connection that will remain fixed and permanently installed at all times.
    No, if you were planning to have the AirPort Time Capsule connect wirelessly and extend the Asus WiFi signal, since it would not be compatible with another manufacturer's router for that purpose.
    Another way of saying the same thing here would be that if you want to extend the network wirelessly, it will take two Apple routers to do so

  • I have a 2009 Mac mini and the wireless card has never worked, would I be able to cover it with my three year extended warranty?

    I have a 2009 Mac mini and the wireless card has never worked, would I be able to cover it with my three year extended warranty?

    matthewfromwhangarei wrote:
    I have a 2009 Mac mini and the wireless card has never worked, would I be able to cover it with my three year extended warranty?
    If you mean AppleCare, then I would believe the answer will be yes.
    First make sure you have a full backup of everything on your Mac, then run, don't walk to your nearest Apple store.
    Note: Due to your Mac now being in computer years, somewhat elderly, Apple may not have the require parts in stock. This will either mean you might have to leave it with them for a number of days, or maybe they will offer you a new Mac mini. While a new Mac mini (if offered) might be a welcome possibility be aware that the new Mac mini no longer has a CD/DVD drive and it comes with Mac OS X Lion and as a result might not run some of your old software.

  • Iv bought a touchpad app for my iPhone 5 to use on my Mac mini, all the functions work accept the zoom one, how can I fix this problem

    Iv bought a touchpad app for my iPhone 5 to use on my Mac mini, all the functions work apart from the zoom one. How can I fix this please

    Iv bought a touchpad app for my iPhone 5 to use on my Mac mini,''
    Considering the app for the iPhone is for iOS, you may have problems using it on the Mac (Mac OS X)
    Two different operating sysems.
    From iTunes for the touchpad app:
    Requirements: Compatible with iPhone, iPod touch, and iPad. Requires iOS 5.1 or later. This app is optimized for iPhone 5.
    From here >  https://itunes.apple.com/us/app/touchpad/id297623931?mt=8

  • I want to link my Mac Mini through my independent hifi system, which forms part of my home tv system which is the monitor I am using with the Mac Mini. The hdmi cable I am using comes from the receiver of the tv. I cannot get sound from the Mac Mini. Do

    I cannot link my new MacMini with my TV's sound system. It's a Pioneer screen & receiver with an independent Pioneer Amp. The Mac Mini does not pick up the sound through the hdmi cable, so how do I get sound going through the MacMini so I can appreciate the music and films I want to hear. Do I need another piece of Apple kit? I have seen 'Express' on Apples web site. Surely I dont have to pay for this as well?
    I used to have an Apple TV box which had a seperate audio connection from my Pioneer Amp and it worked great.
    Help will be appreciated

    The Mac Mini is going to be used for an Internet connection on the Pioneer Plasma/receiver so I can also play stored films from a seperate hard drive. The receiver has an HDMI connection which I have connected the Mac Mini too. the picture is fine, but there is no sound. I have checked the 'sound' settings on the Mac Mini and it registers the Pioneer PDP receiver is connected but states it has no audible connection?

  • How do i connect my new mac mini to the thunderbolt display

    how do i connect my new mac mini to the thunderbolt displa,  It arrives tomorrow?

    It has a built-in Thunderbolt cable, see here: http://www.apple.com/displays/specs.html
    So assuming your mini has a thunderbolt port (you said it's new so I assume it does), you'd just plug the display's thunderbolt cable into the mini's Thunderbolt port.

  • I have no audio from the mac mini to the hdtv via hdmi cable.

    This started immediately after the latest "apple software update"  I updated it automatically on 6/24/2011.  I have an elgato eye tv connected to the mac mini that provides BOTH audio and video through the HDMI to the HDTV.  The elgato eye tv works fine.  I get both audio and video. 
    However, I only get picture and NO sound from the mac mini to the HDTV via the HDMI output.  No streaming audio either - only picture. Ive tried pandora, netflix, hulu, etc.  I even put in a DVD into the mac mini and again I receive a picture through THE HDMI but no audio.
    I've shutdown and rebooted.  I've disconnected power and reconnected power.  I've gone into the system preferences, audo, and highlight the SONY HDTV as the output.  But still nothing.  I do notice when I toggle between the "internal speakers' and the HDMI option, the audio arrow on the lower right is bright blue during the internal speakers option but is grey when the HDMI option is connected. 
    I called apple care.  Since I'm 98 days past my 90 days of coverage there is no help via human being.  They offered me to set an appointment at the local apple store but they suggested I bring down my 60 inch HDTV with me to the store to be sure it is not a "Sony" issue.  I hope someone can help me resolve this without having to put this mac mini on craigslist and taking a $ hit.
    This was not an issue yesterday.  It became an issue after the latest and greatest "update" to prepare our machines for the lovely lion.
    Thanks.

    I have the same issue.  I also have the 2010 mac mine and use hdmi for audio to my receiver.  I get audio from eye tv with no problems, but it seems to lock the path so that only it can use that path for audio.  If I restart the computer and do not start eye tv everything else works with hdmi audio.  I have tried using the system settings and changing the source there but it doesnt seem to matter.
    David

  • I just bought a mac mini over the weekend. I saved items from my old G4 to an external hard drive. I go to plug in the external hard drive and the new computer is not recognizing it. Help.

    I just bought a mac mini over the weekend. I saved items from my old G4 to an external hard drive. I go to plug in the external hard drive and the new computer is not recognizing it. Help.
    Here is the information I have. The external hard drive is a 120GB Acomdata. It has both USB and Firewire. When I go to plug in to the mac mini through USB, it is not being recognized. When I switch to Firewire on the old computer I can see it, however when I go to USB it is not being recognized (even on the old computer).
    I'm at a loss as to what to do. Any advice would be helpful.

    Shalese wrote:
    Have you ever tried the FW 400 to 800 adapter?
    I have used them on multiple occasions and they work just fine.
    Try this (maybe you already have):
    -Boot Mini with drive disconnected.
    -Do not connect drive but turn it on
    -wait a few seconds for drive to spin up
    -plug cable into the Mini then into drive.
    This is an old drive and may have some timing
    issues.
    I had an Acomdata drive a long time ago.  It
    worked fine with FW but USB was flakey.

  • Can i use 2gb memory in one slot in my 2006 Mac mini as the 2 slots of 1gb only reports only 1gb memory, both memory work ok in the one slot

    Can I use 2gb memory in one slot in my 2006 Mac mini as the 2 slots of 1gb only reports as 1gb memory, both memory work ok in the one slot as I have swapped them over

    To my knowledge 1GB modules are the max. size for the 2006 Mini.
    2GB modules are not recognized/useable.
    Sorry
    Stefan

  • I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

    I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

    Hello, since nobdy else has replied...
    Long shot, but...
    Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there.

  • Mac mini and the old mac iBook clamshell

    Does anyone know if the old iBook clamshell can be used as the monitor and keyboard with the Mac mini? I've got one and I'd like to be able to use it.
    What about the the old iMac blueberry bubbles/OS 9.2. Can I use this with a Mac mini as the monitor, keyboard and mouse?

    Welcome to Apple Discussions!
    The simple answer to your question is that no, your iBook or iMac can't be used the way you hope. Neither has any way to get the mini's video output into the iBook or iMac for display purposes. Obviously the iMac keyboard can be used with the mini, but not the iBook's.
    This question comes up regularly here in one form or another, with users hoping to use laptops or iMacs as input/out devices for a mini, but it can't be done. What can be done in many situations is to connect the mini and 'host' system by ethernet and use a VNC solution (such as Chicken of the VNC http://sourceforge.net/projects/cotvnc/) to control the mini from the host. basically the mini appears in a window on the host system's desktop. However most, if not all, VNC-type solutions will require that the host is running MacOS X, not OS9 or earlier, and even when it does work, performance is really not that great. Aside from that, a screen, keyboard and mouse is required for the mini's initial out-of-the-box setup anyway.

  • I am going to buy a mac mini i7 with 3 thunderbolt displays for forex trading. the question is if i use bootcamp and run windows on the mac mini will the displays still run the same way as if i was running it on Lion?

    I am going to buy a mac mini i7 with 3 thunderbolt displays for forex trading. the question is if i use bootcamp and run windows on the mac mini will the displays still run the same way as if i was running it on Lion?

    No idea if Windows will do it, but you can run Windows without Bootcamp & have OSX available at the same time, which should give you all the Monitors that OSX uses.
    Parallels...
    http://www.parallels.com/
    VmWare Fusion...
    http://www.vmware.com/mac

  • Any chance the Mac mini and the Apple TV will be combined into one unit?

    Any chance the Mac mini and the Apple TV will be combined into one unit?

    No.
    The Apple TV is the guts of an iPad without the screen or battery running a different build of the OS. Ie, its very cheap to make and runs an ARM processor (like all iDevices)
    The Mac mini is 6x the price and is a full intel computer running the OS X.
    Now, it could be that the Apple TV gets more powerful and its OS more diverse and "computer like" (apps + iCloud for example), but for now they're still coming from totally different directions.
    They just happen to look alike

  • I'm having trouble with installing a 8g kit in my late 2009 mac mini. when the parts are installed all i get is a beeping sound, is there any way to get around this?

    i'm having trouble with installing a 8g kit in my late 2009 mac mini. when the parts are installed all i get is a beeping sound, is there any way to get around this?

    What is the source & link to this 8 GB kit please?
    Can you count the beeps or flashes?
    1 beep = no RAM installed
    2 beeps = incompatible RAM types
    3 beeps = no good banks
    4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
    5 beeps = processor is not usable
    In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
    Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
    http://support.apple.com/kb/HT1547

  • Getting problem while installing Snow Leopard (10.6.3) on my Mac Mini. The following issue is showing :  "mac os x snow leopard cannot be installed on this computer"  And My Mac Configuration details:  Model Name: Mac Mini Model Identifier: Macmini2,1

    Getting problem while installing Snow Leopard (10.6.3) on my Mac Mini. The following issue is showing : 
    "mac os x snow leopard cannot be installed on this computer" 
    And My Mac Configuration details:  Model Name: Mac Mini Model Identifier: Macmini2,1
    Intel Core 2 Duo
    1.83Ghz
    l2Cache: 2mb
    Memory : 2GB
    Bus Speed: 667MHz
    Please help me......
    Thanks

    Actually i have Mac OS X 10.5.4 DVD, I need to upgrade it to Snow Loepard(OS X 10.6)...
    Please suggest me what to do???
    Thanks

Maybe you are looking for

  • Using Translate() function of XSLT ...

    Hi guys I have an xml document that i am converting into an html document using XSLT. I need to replace the XML new lines(&#10) with html new lines (<br>) while the xslt transform takes place on my xml document. For this I have found the translate fu

  • Ssh -X solaris 9 host fails to set DISPLAY

    i'm running Suse 9.1 Pro as my graphis client. x86 doesn't quite work yet on my host. i'm trying to run smc from my E250 (headless) to my Suse 9.1 desktop. the E250 is running Solaris 9. when i ssh -X and echo $DISPLAY, DISPLAY is empty. howerver, i

  • JavaFX stage crashing on program start, Windows 7 Home Premium, NB 6.9 RC2

    Hey all, I'm creating a Java/JavaFX application and have been using an interface to pass data back between the two programs. Upon running the program in NetBeans 6.9 RC2, it sometimes runs but often crashes. I'll post up some code, but I think it is

  • Can I continue to use my existing TM dataset after re-installing OS X

    I just completed a complete system re-install on my iMac, using the Leopard install DVD, and my time-machine backup on a Drobo. Worked great, the issues I was having before have been fixed, I'm good to go. However, I would like to carry on adding to

  • 2007 B

    Hi all, we want to upgrade 2005 b to 2007 b ,we are currently using SBO 2005 B Pl-42. but we are not having upgrade exe to upgrade to 2007 B. We have 2007 B setup ,if we durectly run the 2007 B setup will it upgrade  to 2007 b. suppose we directly ru