Same client no has impact in diff systems

Hi,
Currently we have upgraded to ECC and setup Dev and QA systems and in QA we have the Client 500 and have setup a logcial system ..MR1CLNT500 and after 1 month we are going to setup Production system with Client No :500..
My question is if we have the same client no in both the systems does it have any impact...
If any precautions needs to be taken pls let me know..
Regds,
Satyanarayana N.

Hi Satyanarayana N.,
You can keep the same client for PRD, OQ and DEV even for sanbox also.
I think your <SID> will be different so the logical name will be also different.
No issue.
Best WIshes.
Kumar

Similar Messages

Error Message from SLD - "Selected client already has a business system..."

I have successfully created and test a File to IDOC scenario from a File system to ERP ECC 6.0 (client 101, system name sapdbt02)
Right now, I creating another File to IDOC scenario for a different file system to the same ERP ECC 6.0
At the SLD, I would need to create two new Techncial System and Two new Business System.
However when I creating a Business system for the ABAP Type for the ERP ECC 6.0, when selected the same client and system name of the first scenario that I have done, I got this error message
"Selected client already has a business system associated, please select a new client or system"
I am puzzled that I would need to a configure a new client for the same system ID for another FIle to IDOC scenario
going to the same ERP system
Please advise.
Best Regards
Freddy Ng

For example:-
create business system for R3 system in SLD as suggested by stefan. I assume that u have one R3 system which is either sending or receiving data from XI.
assign the system to ur scenarios, u can use common IDOC/RFC/XI channel for sending data to R3 system.
Separate R3 business system is required incase u have to send data to different R3 system.
If u have different files coming from different File system in that case better to create different business service and use them.
chirag

IDOC error - same client same system

Hi guru,
i have a requiremnt to generate the IDOC for the same and same client. actually i have to get the data from application server and i have to generate the IDOC.
for this i have created a Zreport and passed the data from application server to segment and i called the
FM "MASTER_IDOC_DISTRIBUTE". after executing the Zreport, IDOC is generated and show the error
status as 29.i.e. Receiver of IDoc is its own logical system.
my logic is as follows.
MOVE 'LS' TO w_edidc-rcvprt.
MOVE 'SBECLNT130' TO w_edidc-rcvprn.
MOVE 'ISU_MR_UPLOAD' TO w_edidc-mestyp.
MOVE 'ISU_MR_UPLOAD01' TO w_edidc-idoctp.
pls let me know the solution for this problem.
Regards,
Balu

Hi,
To send an IDoc from the SAP system to the external system, you must define outbound parameters for the message type and all relevant partners. This is valid even if your receiving system is same as sending systems.
For more information, see Interfaces ® External Systems ® Configure Warehouse Management ® Communication R/3 -> External System ® Maintain Partner Profile in the Implementation Guide for Warehouse Management.
If the system cannot find the partner (that is, the connected partner system) for sending the IDocs, proceed as follows:
Define the missing partner profile.
Resend all existing IDocs, which the system has not yet been able to send.
What is the partner profile of your system ?
Check your partner profiles in WE20 and maintain your message type in Outbound and Inbound parameter for the system.
KR Jaideep,

SLD: Pointing two business systems to the same client...

Hi Guys,
Is there anyway to make two business systems point to the same client(on the same r/3 technical system)? how about a work around?
Thanks,
Harsh

Harsh,
>>Finally all collapse to one client in production.
Even though you will have multiple Business Systems in every envrionment, the final transport will happen from only one environment.
DEV --> QA --> PROD. In this case, objects are moved from dev to qa and then from QA to prod and so, all you will need is the trasnport target created in the QA business systems pointing to the Prod busines system and do the transport.
>While transporting to a new SLD(quality to prod) can I choose one transport target for multiple source business systems?
Take a look at this document for multiple SLD transports. Should answer all doubts,
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/9e76e511-0d01-0010-5c9d-9f768d644808
Regards,
Bhavesh

Can IDoc sender and receive system be the same client?

thanks.
I think one client can't assign to two logical system.so?

Can IDoc sender and receive system be the same client?
yes
Regards,
Prateek

System NSP client 001 has no logical name!

HI all.Im install SapNetWeaverSneakPreviewABAP.
-client copy (txn SCC4) into say 001
-log on to 001 with **** and pass
transaction SCCL source client 000 and target client 001.
-now run transaction RSA1 for initial bw setup
AND SAP output System NSP client 001 has no logical name!
And two button - create and assign...
Please howto info

hi,
have you assigned client 001 to logical system ?
spro->bus inf warehouse->link to other systems->general connection settings->assign client to logical system.
take a look
http://help.sap.com/bp_biv235/BI_EN/BBLibrary/documentation/B84_BB_ConfigGuide_EN_DE.doc
hope this helps.

ALE process on the same client but on diffent System

Hi all
Is it possible to create a ALE process on the same client but on diffent System?
Thanks,
Raj

Hi,
if you mean that you want to send data from client X on system A to client X on system B then yes.
Cheers

Can we have ABAP and PI in same client in the same system?

Hi Consultants,
Can inbound and outbound scenarios work, if the ABAP and PI (7.01) is in the same client ?
If yes, then can you please let me know the settings and configurations required.
Thanks in advance.
Regards,
Naushad

Hello
Please elaborate on your requirements. Are you talking about proxy scenarios? Do you mean can the PI Integration Server client act as a proxy Sender/receiver?
If yes, I don't think this is possible.
Regards
Mark

Server client 000 has no logical name!

When worked on NW7.0 Data warehouse Workbench, I got message: "System MYSERVER1 client 000 has no logical name." The screen has two options: "Create", or "Assign". Which action I should choose to continue work on? Are there any impacts on my system?
Thanks !
Mike

Mike first you have to create a Logical System say <SID>CLNT000 and then assign this to client 000.
When you assign it wil take you to the SCC4 scrren. Double click on your client(000) and then fill up the Logical System field with <SID>CLNT000
The same can also be done thro SALE-> IDOC/ALE -> Basic Settings -> Logical Systems -> Define LS and Assign LS.

MM-SUS and EBP-SUS in the same client

Hi experts
I have a doubt about implementationMM-SUS and EBP-SUS in the same client, If I send a PO from MM to SUS and after send a PO from EBP to SUS to the same vendor, the vendor will be able to see 2 POs with just one logon?
As I know when I replicate a vendor from MM to SUS a Business partner is created and when I replicate a the same vendor from EBP to SUS a new Business partner is created and are diferent BP so a user and pass diferent .
Thanks
Nilson

Hi Nilson,
If i understand your scenario, you'll replicate an existing R/3 vendor to EBP. The vendor will be a direct vendor in R/3 while the same would be used as for Indirects in EBP.
Well, when you replicate the R/3 vendor to EBP, the vendor has the R/3 link in the form of Backend Logical systen name in EBP.
So when you replicate the vendor from R/3 or EBP, there will be ideally only one entry for the vendor with references to R/3 and EBP systems.
Hope this clarifies your question.
Cheers,
Akash

Is SAP BI reporting is possible in ECC 6.0 with same client

Hi all,
                         My requirement is, we need to design SAP BI data flow in ECC 6.0 with same client only. Now I am designing the BI data models as per the requirement of SD sales reports in ECC 6.0.For this, when i was extracting the data from SD datasource(2lis_11_vahdr) in RSA3 its showing 0 records,actually as per VA01 some records are available but its not showing in the RSA3.
                          My doubt is , is it possible to extract the data from ECC 6.0 and load the data to the datatargets and get the SAP BI reports in ECC6.0 with the same client.
                          Please suggest as soon as possible.
Thanks

It is possible to load the data from the same client. It all depends on the source system and the client which has been connected in the RFC connection.
Let me know if this helps.
Regards,
Avinash

ROS (without SUS) and EBP in same client-Transferred BP status?

Friends,
We are working on SRM 7.
The ROS (without SUS) and EBP are implemented on the same SRM client.
In supplier registration process, when the accepted business partner is transferred from ROS to EBP, a supplier is correctly created in EBP client with the same business partner number, but the status of the transferred business partner is not updated from 'ACCEPTED' to 'RELEASED', hence there is risk that user can transfer the business partner again.
As per OSS note 857386, the status released is set automatically by the system when an accepted supplier has been distributed. Also the status is valid only for DISTRIBUTED suppliers, that is, ONLY for suppliers TRANSFERED through OPI.
I understand, if ROS (without SUS) and EBP are deployed on separate clients in same server then when the accepted business partner is transferred from ROS to EBP, system triggers an XI message to update the ROS business partner status to 'RELEASED'. Is my understanding right?
How do we update the transferred business partner status to RELEASED when ROS and EBP are on same client?
Regards,
Sandeep Parab
Edited by: Sandeep Meghashyam Parab on Apr 9, 2010 11:43 AM

Hi Sandeep,
I too have a requirement to implement ROS without SUS in SRM 7.0 PPS. Can you send the config guide or steps to follow both in the ROS side and in the SRM Side. Your kind help will be rewarded and highly appreciated.
with regards,
Freemind

Provider client software has not been properly installed on this server

Hi All,
I am in a process of setting up the DR for the SAP R/3 4.7 system, which is on Windows and SQL 2000 SP3.
While installing the SPA on the DR Server, i am facing the below attached problem in the DB Instance installation. the CI Installation goes through fine. but it stop in the Database Load section. with the screen showing Running 3 and waiting 0.
Details:
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: START OF LOG: 20080220124003
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/620/src/R3ld/R3load/R3ldmain.c#6 $ SAP
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: version R6.20/V1.2
E:\usr\sap\GRP\SYS\exe\run/R3load.exe -ctf I I:\EXPORT6/DATA/SAPAPPL0.STR I:\EXPORT6/DB/DDLMSS.TPL C:\SAPinst MSSQL SAPINST/SAPAPPL0.TSK MSS -l C:\SAPinst MSSQL SAPINST/SAPAPPL0.log
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: job completed
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: END OF LOG: 20080220124003
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: START OF LOG: 20080220124039
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/620/src/R3ld/R3load/R3ldmain.c#6 $ SAP
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: version R6.20/V1.2
E:\usr\sap\GRP\SYS\exe\run/R3load.exe -dbcodepage 1100 -i C:\SAPinst MSSQL SAPINST/SAPAPPL0.cmd -l C:\SAPinst MSSQL SAPINST/SAPAPPL0.log -loadprocedure fast
DbSl Trace: OpenOledbConnection : CoCreateInstance failed. rc: REGDB_E_CLASSNOTREG.
DbSl Trace: OpenOledbConnection : Provider client software has not been properly installed on this server.
DbSl Trace: OpenOledbConnection : CoCreateInstance failed. rc: REGDB_E_CLASSNOTREG.
DbSl Trace: OpenOledbConnection : Provider client software has not been properly installed on this server.
DbSl Trace: OpenOledbConnection : CoCreateInstance failed. rc: REGDB_E_CLASSNOTREG.
DbSl Trace: OpenOledbConnection : Provider client software has not been properly installed on this server.
DbSl Trace: failed to establish conn. 0
(DB) ERROR: db_connect rc = 256
DbSl Trace: OpenOledbConnection : CoCreateInstance failed. rc: REGDB_E_CLASSNOTREG.
DbSl Trace: OpenOledbConnection : Provider client software has not been properly installed on this server.
DbSl Trace: OpenOledbConnection : CoCreateInstance failed. rc: REGDB_E_CLASSNOTREG.
DbSl Trace: OpenOledbConnection : Provider client software has not been properly installed on this server.
DbSl Trace: OpenOledbConnection : CoCreateInstance failed. rc: REGDB_E_CLASSNOTREG.
DbSl Trace: OpenOledbConnection : Provider client software has not been properly installed on this server.
DbSl Trace: failed to establish conn. 0
(DB) ERROR: DbSlErrorMsg rc = 29
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: job finished with 1 error(s)
E:\usr\sap\GRP\SYS\exe\run/R3load.exe: END OF LOG: 20080220124040
The same error come in a lot of other scripts of DB Load.
I have installed the SQL Server 2000 SP3 with Hot fix 929.
Could some one help me to get the same fixed
Thanks a lot in advance.
Best Regards
Mahendra K
+91 9867183370

I have this problem too on an ASUS windows 8.1 PC.
Since installing itunes 11.1.5
Problem seems to be that the AMDS Apple Mobile Device Support does not install.
I also tried all options on this forum....
Who can help???
Thnx
Oscar

How can we confiure idoc in same client sender as well as receiver

HI Gurus,
How can we create the ale/idoc within the same client, sender as well as receiver.
can u give me step by step procedure.
thanks in advance.

Hi kumar,
see this links these may help u.
http://help.sap.com/saphelp_nw04/helpdata/en/90/c4b523c4c411d2a5ee0060087832f8/content.htm
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a8424011-0d01-0010-e19d-e5bd8ca52244
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/201769e0-3174-2910-e287-baa58d198246
Go through the following Tcode for ALE
ALE IDOC
Sending System(Outbound ALE Process)
Tcode SALE ? for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 ? Create Model View
Tcode BD82 ? Generate partner Profiles & Create Ports
Tcode BD64 ? Distribute the Model view
Message Type MATMAS
Tcode BD10 ? Send Material Data
Tcode WE05 ? Idoc List for watching any Errors
Receiving System(Inbound ALE )
Tcode SALE ? for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 ? Check for Model view whether it has distributed or not
Tcode BD82 -- Generate partner Profiles & Create Ports
Tcode BD11 Getting Material Data
Tcode WE05 ? Idoc List for inbound status codes
ALE IDOC Steps
Sending System(Outbound ALE Process)
Tcode SALE ?3 for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 !V Create Model View
Tcode BD82 !V Generate partner Profiles & Create Ports
Tcode BD64 !V Distribute the Model view
This is Receiving system Settings
Receiving System(Inbound ALE )
Tcode SALE ?3 for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 !V Check for Model view whether it has distributed or not
Tcode BD82 -- Generate partner Profiles & Create Ports
Tcode BD11 Getting Material Data
Tcode WE05 !V Idoc List for inbound status codes
Message Type MATMAS
Tcode BD10 !V Send Material Data
Tcode WE05 !V Idoc List for watching any Errors
1)a Goto Tcode SALE
Click on Sending & Receiving Systems-->Select Logical Systems
Here Define Logical Systems---> Click on Execute Button
go for new entries
1) System Name : ERP000
Description : Sending System
2) System Name : ERP800
Description : Receiving System
press Enter & Save
it will ask Request
if you want new request create new Request orpress continue for transfering the objects
B) goto Tcode SALE
Select Assign Client to Logical Systems-->Execute
000--> Double click on this
Give the following Information
Client : ERP 000
City :
Logical System
Currency
Client role
Save this Data
Step 2) For RFC Creation
Goto Tcode SM59-->Select R/3 Connects
Click on Create Button
RFC Destination Name should be same as partner's logical system name and case sensitive to create the ports automatically while generating the partner profiles
give the information for required fields
RFC Destination : ERP800
Connection type: 3
Description
Target Host : ERP000
System No:000
lan : EN
Client : 800
User : Login User Name
Password:
save this & Test it & RemortLogin
3)
Goto Tcode BD64 -- click on Change mode button
click on create moduleview
short text : xxxxxxxxxxxxxx
Technical Neme : MODEL_ALV
save this & Press ok
select your just created modelview Name :'MODEL_ALV'.
goto add message type
Model Name : MODEL_ALV
sender : ERP000
Receiver : ERP800
Message type :MATMAS
save & Press Enter
4) Goto Tcode BD82
Give Model View : MODEL_ALV
Partner system : ERP800
execute this by press F8 Button
it will gives you sending system port No :A000000015(Like)
5) Goto Tcode BD64
seelct the modelview
goto >edit>modelview-->distribute
press ok & Press enter
6)goto Tcode : BD10 for Material sending
Material : mat_001
Message Type : MATMAS
Logical System : ERP800
and Execute
7)goto Tcode : BD11 for Material Receiving
Material : mat_001
Message Type : MATMAS
and Execute --> 1 request idoc created for message type Matmas
press enter
Here Master Idoc set for Messge type MATMAS-->press Enter
1 Communication Idoc generated for Message Type
this is your IDOC
Change Pointers
I know how to change the description of a material using ALE Change Pointers.
I will give the following few steps
1) Tcode BD61---> check the change pointers activated check box
save and goback.
2) Tcode BD50---> check the MATMAS check box save and comeback.
3) Tcode BD51---> goto IDOC_INPUT_MATMAS01 select the checkbox save and comeback.
4) Tcode BD52---> give message type : matmas press ok button.
select all what ever you want and delete remaining fields.
save & come back.
5) 5) go to Tcode MM02 select one material and try to change the description and save it
it will effects the target systems material desciption will also changes
6) goto Tcode SE38 give program Name is : RBDMIDOC and Execute
give Message type : MATMAS and Executte
ALE/IDOC Status Codes/Messages
01 Error --> Idoc Added
30 Error --> Idoc ready for dispatch(ALE Service)
then goto SE38 --> Execute the Program RBDMIDOC
29 Error --> ALE Service Layer
then goto SE38 --> Execute the Program RSEOUT00
03 Error --> Data Passed to Port ok
then goto SE38 --> Execute the Program RBDMOIND
12 Error --> Dispatch ok
Inbound Status Codes
50 Error --> It will go for ALE Service Layer
56 Error --> Idoc with Errors added
51 Error --> Application Document not posted
65 Error --> Error in ALE Service Layer
for 51 or 56 Errors do the following steps
goto WE19 > give the IDOC Number and Execute>
Press on Inbound function Module
for 65 Error --> goto SE38 --> Execute the Program RBDAPP01 then your getting 51 Error
1)EDI
Electronic Data Interchange
Cross-company exchange of electronic data (for example business documents) between domestic and international business partners who use a variety of hardware, software, and communication services. The data involved is formatted according to predefined standards. In addition to this, SAP ALE technology is available for data exchange within a company.
2) ALE
A means of creating and operating distributed applications.
Application Link Enabling (ALE) guarantees a distributed, but integrated, R/3 installation. This involves business-controlled message exchange using consistent data across loosely linked SAP applications.
Applications are integrated using synchronous and asynchronous communication - not by using a central database.
ALE consists of the following layers:
Application services
Distribution services
Communication services
ALE/ IDOC/ XML
http://www.sapgenie.com/sapgenie/docs/ale_scenario_development_procedure.doc
http://www.thespot4sap.com/Articles/SAP_XML_Business_Integration.asp
http://help.sap.com/saphelp_srm30/helpdata/en/72/0fe1385bed2815e10000000a114084/content.htm
Regards,
karthik

Connect 2 BW to the same client in R3?

Hi,
Is it possible to connect 2 BW to the same client of R/3 as a source system? Will this mess up the delta queue like in RSA7? Or, the R3 system has separate queue for each BW? Please advise.
Thanks,
Jeff

Hello Roberto,
Could you please give me the step to step procedure of doing it? I really appreciate your help and full points will be awarded
Experts,
I have two BW clients with same naming convention (BWP400).. Can I connect 2 BW systems with same logical name to one R/3 system. If not how can I change the logical name of one of the system with out affecting any data or settings it .
One of the prod box is new one and yet to load data.
All inputs are highly appreciated
Thanks and Regards,
Harish

Same client no has impact in diff systems

Similar Messages

Maybe you are looking for