Same SSID, different vlans
I currently have a 4402 in place, with my main office building working fine.
We are looking at bringing in the wireless at 4 other sites, but we want to use the same SSID.
How would I go about assigning different vlans (networks) to the same SSID.
You can use the "AAA Override" feature on controller. You need to have different dynamic interfaces for different vlans configured on the controller. After sucessful authentication, radius server could pass the dynamic interface information to the controller and controller can put users to different vlans according to the feedback from radius server:
http://www.cisco.com/univercd/cc/td/doc/product/wireless/control/c44/ccfig40/c40sol.htm#wp1086421
Zhenning
Similar Messages
-
Error fetching network with same SSID, different floors
Dear,
I would like help from you, because I have a problem and I can not detect.
I have six devices installed in the WAP model 4410N on two different floors, and a third on each floor.
Both are with the same SSID, but when I'm walking him on a quest equipment that is in another floor, which causes the machine to drop the connection due to fluctuations and barriers such as walls, doors, windows, elevators, etc. .. .
I wonder how to detect only the AP network of walking even with the same SSID.
VLAN use one at each andaar.
If you have any suggestions thank you.
thank you
AndersonHi Anderson,
It sounds like you have 5 access point in standalone and 5 SSID broadcasting but you can't know the difference between which SSID is good depending where you are at.
If you can use any of the AP as a repeater (you may repeat 2 additional ap), when the signal strength of the original connection is low enough, it should fall to the more powerful strength of the repeated SSID.
Additionally, if you'd like to use more than 3 AP in a repeater group, you may want to look in to something like the AP541N. These devices support clustering, up to 10 units.
-Tom
Please rate helpful posts -
Same SSID different MAC address
Ok... This is the best place for me to post this I think...
I am sharing an internet connection and am relatively close to the router (linksys) but because of the materials my building is constructed with I get a **** poor connection. So, there is a closer range extender that I can connect to, the range extender is also a linksys range extender, and I have no problems when I connect to it. The only problem is actually getting connected to it in the first place. My computer will automatically connect to the router rather than the base station. They both have the same SSID, and obviously different MAC addresses. Is there a way to force my computer to only connect to the range extender and ignore the signal from the router?I have no problems with the range extender itself. It works great. The problem is that my airport card cannot tell the difference between the range extender and the router. Sometimes it will connect to the router, and sometimes to the range extender. I want to force it to connect to a specific MAC address rather than using only the SSID. Is there a way to do this?
-
Two SSIDs; different VLANs; second VLAN can't talk to Internet
I've got an ASA 5505 firewall with internal interface 192.168.65.1 on port 1 and a WAP connected to port 5 with the address 10.10.1.1. The WAP has two SSIDs configured; one is on VLAN 1 and the other on VLAN 14. The firewall has port 5 configured as a trunk for VLAN 1,14 and the interface was configured a VLAN 14.
If I connect to the WAP using the SSID on VLAN 1 I get an address of 192.168.x.x from our internal DHCP server and have full connectivity to the internal and external networks. If I connect to the SSID on VLAN 14 I get an address of 10.10.1.x from the firewall DHCP server but am unable to connect to anything.
When connecting to the SSID on VLAN 14 I want to be able to access the external interface but not anything internally. I have configured a firewall access rule to allow 10.10.1.0/24 to outside and deny 10.10.1.0/24 to 192.168.0.0/16 but this hasn't worked.
Any ideas?You need to configure an IP helper on the appropriate VLAN interface(s). Routers, by default, will not forward broadcast packets. Since DHCP client messages use the destination IP address of 255.255.255.255 (all Nets Broadcast), DHCP clients will not be able to send requests to a DHCP server on a different subnet unless the DHCP/BootP Relay Agent is configured on the router. The DHCP/BootP Relay Agent will forward DHCP requests on behalf of a DHCP client to the DHCP server. The DHCP/BootP Relay Agent will append its own IP address to the source IP address of the DHCP frames going to the DHCP server. This allows the DHCP server to respond via unicast to the DHCP/BootP Relay Agent. The DHCP/BootP Relay Agent will also populate the Gateway IP address field with the IP address of the interface on which the DHCP message is received from the client. The DHCP server uses the Gateway ip address field to determine the subnet from which the DHCPDISCOVER, DHCPREQUEST, or DHCPINFORM message originates.
See more at the following document, with configuration steps and examples:
http://www.cisco.com/warp/public/473/100.html#configdhcpbootpciscoios -
Same SSID, different passwords
Greetings all,
My work takes me to several schools every week, each with the same SSID (let's call it "faculty"), but each with a different password. I have to enter all the settings manually everytime I walk into a new school, and I'd love for the macbook (and iPhone too) to just remember all the settings for each school. I'm only a teacher so I have no power to change SSIDs or passwords. Is there a way for ML to remember networks by the AP's MAC address (and not just the SSID), or some other method?
Thanks!I have 3 linksys routers and the iPad has been able to connect to them all. I settled on the Linksys WRT54GL because the others are old and starting to exhibit dropout problems.
My suggestion would be to temporarily shorten your password to one or two digits and see if that helps. Before playing around with the Linksys I would suggest that beforehand you save your config file in case you need to restore the router.
I am on G band only, channel 6. My wireless security is set to WPA Personal, TKIP+AES, and I have a 26 digit WPA shared key. BTW, the 26 digit key is a real pain in the butt, but perhaps provides additional security.
Like nearly everyone else, I am occasionally experiencing short internet disconnects followed by an automatic reconnect. I'm hoping the next iPad upgrade will remedy this. -
Hi,
Has anybody in this forum ever deployed a wireless network with the same SSID, but using 2 different vendors.
We have a warehouse and office space separated with concrete wall. In the warehouse, we have one vendor
and in office, we have another vendor. We want to use the same SSID in order to facilitate roaming.
Is this feasible?
ThxIt will not work well in some environments. Two separate systems, lightweight and autonomous does not communicate with each other to support roaming.
If you have standalone access points using open or maybe preshared key, then it can work since each roam required a full reauth. As long as the users are in the same subnet, it can work. If your using 802.1x then the roam will be very slow due to full reauths.
Sent from Cisco Technical Support iPhone App -
Flex Connect Across Multiple VLANS same SSID
I just need to find that if we have flex connect setup for differnet vlans using single controller, will roaming works when client connects to AP in a differnet VLAN but using same SSID.
Example below:
1) Client connects to AP on specific SSID mapped to VLAN 100, get an IP address ..all good at this point
2) Client walks and connects to a differnet AP on same SSID but mapped to VLAN 200...at this point I observe client doesnt get a new IP address in fact it retain IP from step-1 and there is no connectivity
3) Client walks back to first AP and connectivity is restored
Why in step-2 client doesnt gets a new IP from VLAN 200 even when it shows connected to AP.Just to add to Rasika.... L3 isn't supported....I just ran into this a few days ago.... clients should request another dhcp when roaming to another FlexConnect AP that is mapped to a different VLAN. The issue is, that some clients don't try to renew their dhcp address and gets stuck with the default 169.x.x.x. I see this with Apple devices in general and what we are going to do is get rid of the multiple vlan setup (vlan per floor) and create a bigger vlan that the SSID will be mapped to.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Map 300 different VLANs to a SSID?
Hi Everyone,
I've just come across a situation where the customer requires to have their 300 different VLANs (they got 300 stores across AU) to be mapped to the same SSID. I know this is doable by creating an interface group on the WLC that contains all 300 VLAN interfaces, then map the interface group to the SSID. However, is there a better way to do it? I meant I don't think creating 300 interfaces on the WLC is a good idea from a managment point of view.
Thanks you in advanced for your time and for sharing your wisdom.
Regards,
Nhan.Hi Nhan,
This post in Small Business Forum and you need to address this in Enterprise Level Forum.
Thank you. -
Howto block p2p traffic of clients connected to the same ssid on different wlc
Hi all,
I use two wlc 4400 (4.2.x version) with a mobility domain and one ssid, both wlc are connected to a cisco l2 switch infrastructure. On the wlc I use the p2p blocking action 'drop' (http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1209597) to isolate the clients from each other. Does anybody know if only unicast traffic is blocked or also multicast and broadcast traffic like arp requests?
Concerning blocking p2p traffic of clients connected to the same ssid but different controllers I found the following statement in the LAP FAQs (http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml):
===
Q. In autonomous APs, Public Secure Packet Forwarding (PSPF) is used to avoid client devices associated to this AP from inadvertently sharing files with other client devices on the wireless network. Is there any equivalent feature in Lightweight APs?
A. The feature or the mode that performs the similar function of PSPF in lightweight architecture is called peer-to-peer blocking mode. Peer-to-peer blocking mode is actually available with the controllers that manage the LAP. If this mode is disabled on the controller (which is the default setting), it allows the wireless clients to communicate with each other through the controller. If the mode is enabled, it blocks the communication between clients through the controller. It only works among the APs that have joined to the same controller. When enabled, this mode does not block wireless clients terminated on one controller from the ability to get to wireless clients terminated on a different controller, even in the same mobility group.
===
Does anybody know what's the best practise to prevent this inter wlc client traffic? I already read about using acls on the wlc dynamic interfaces, or private vlans on the l2 switch vlans where the dynamic interfaces are connected to. Is it allowed to completely isolate the wlc from each other on these dynamic interfaces with acls or private vlans or do the wlc need to see each other on this interfaces (e.g. heart beat)?
Many thanks in advance,
ThorstenHi Sasha,Thorsten
The bug is Junked and I believe which is what you are running into with your tests:
CSCtr60787 WLC P2P Blocking Set to Forward-UpStream Doesn't Work.
Bugtoolkit : http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
To answer your original query :
ACL is only solution to block client communication on same ssid between 2 wlcs. 5508 works better with ACLs then 44xx platform.
ARP requests will be forwarded to upstream router just like any other traffic. WLC won't proxy arp for clients on same vlan.
Gateway arp's I believe should be handled by WLC . ( Don't quote me on this but I am pretty sure it is ) ..If it was not, then how would client know about gw ?
Multicast traffic is not applicable for p2p.
Your ACL can be as simple as this for the scenario :
WLC 1 - clientvlan = 10
WLC 2 - clientvlan = 10
and you want to restrict users from wlc1-wlc1, wlc1-wlc2, wlc2-wlc2 for same vlan10.
Basically in that case the ACL should look like on both WLCs :
1. Permit statement to talk to gateway.
2. Deny to subnet.
3. Permit all.
4. If DHCP/DNS other services are on same subnet then you would need to add a permit
statement before the deny.
5. Attach the ACL to SSID or dymanic interface.
Thanks..Salil
CSCtr60787 WLC P2P Blocking Set to Forward-UpStream Doesn't Work. -
My office room is near different APs with the same SSID, my Snow Leopard selects automatically to join the AP with stronger signal.
But this AP isn't running well, so I want to force my mac to join a AP with weaker signal.
(I've the same troubel as described in https://discussions.apple.com/message/6470508#6470508)
Note that I'm a guest user and I hanen't access to APs, so I cannot change their SSID.
Any idea how to force Mac to join a specific AP?
Thanks,
adsoMy office room is near different APs with the same SSID, my Snow Leopard selects automatically to join the AP with stronger signal.
But this AP isn't running well, so I want to force my mac to join a AP with weaker signal.
(I've the same troubel as described in https://discussions.apple.com/message/6470508#6470508)
Note that I'm a guest user and I hanen't access to APs, so I cannot change their SSID.
Any idea how to force Mac to join a specific AP?
Thanks,
adso -
The same SSID used at 3 sites and the same vlan for client IP assignment?
we are deploying 5508 controller and LW APs for wireless IP phone 7925G
Controller is installed at site A and there are APs and wireless phones at site B and C as well.
1. can I use the same SSID for all three sites for wireless phones? or have to use 3 distinct SSIDs?
2. If I can use the same SSID, can I associate one subnet e.g 10.10.131.0/24 for wireless IP phones at 3 sites? (our Cisco UCM is fine with this)
3. if I have use 3 distinct SSIDs, do I have to assign three subnets for IP phones at three sites?
thanks for the help!
Ericyes.. this is done by HREAP mode.. the below link will help you out!!
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807cc3b8.shtml
That is, by default the WLAN will get pushed to all APs.. so if you have a single wlan then this will broadcast the SSID and the remotre site clients will connect to it..
Lemme know if this answered your question!!
Regards
Surendra -
I want to use the same SSID in two sites (central y remote)
I have several AP in H-REAP mode, one of them is in a remote location anthe other are in the central location. I want to use the same SSID in both locations with differents VLANS.
In the central site, i have 3 WLANS (SSID) whit 3 different VLAN eachother. I put the local swicthing in one SSID that I want to use in the remote site. In the remote location the users can authenticate and everything works fine but in the central location that SSID doesnt work, the user in the central location can not authenticate.
It seems that i can not use the same WLAN (SSID) and use it en both locations checking the local switching.
What can i do?
Many thanks for your helpLook I have 2 two VLANs Interfaces (vlan 252 & Vlan253) created on WLC, beside the management VLAN (ID 254), and there are 8 AP´s installed at the central location, each AP has been connected to my CORE Switch through switch ports mode Access vlan 254.
th aeuthentitcation i have been used is "LOCAL: WPA-WPA2-PSK" in both locations (Central and remote). In the remote sites, tha AP is connected to a cisco switch through switch port mode trunk, and I use VLAN 251. When the local switching feature is activeted on WLC, I can map the VLAN 251 (in te remote site) to the SSID I am using inthe central site and everything works fine but in the central locations the user can associste to he AP but they can not receive IP from the appropiate VLAN.
I don t know what parameter have to change....
Can you helpme? -
I can to have two SSIDs for all branch of my country, but each ones in a differents subnets,for example:
Area 1
SSID 1 : guest -> 192.168.1.1
SSID 2 : office -> 192.168.2.1
Area 2
SSID 1 : guest -> 192.168.3.1
SSID 2 : office -> 192.168.4.1
I have configured AP-Group, and this works succesfull but only with one SSID, I need two SSID, each one associated a multiples vlans, when the user are connect to SSID guest they receive the correct ip from the subnet corresponding,(Area1 ip address of host is 192.168.1.X and the Area 2 the usuer receibe the address 192.168.3.X both using the same SSID "guest"), How I can reach this requerimients using two SSID?. Using Ap-Group or there is other methods.AP Group VLANs are used in a setup where a Universal WLAN (service set identifier [SSID]) is required but clients need to be differentiated (placed on different interfaces configured on the WLC) by virtue of physical LAPs they associate with. Refer URL
http://cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008073c723.shtml#c2 -
Multiple Cisco Aironet 1131AG access points and same SSID?
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
So my question is this: How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)? Can one of the ap's be WDS and in the same time local radius server with users without Cisco Secure ACS or similar controller or I didn't understand this quite well :-). I followed guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where the part abou Cisco ACS is a problem, so I can use same ap as Local Authenticator as in guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.
Many thanks...Well, just so you know, WDS and local RADIUS authentication is only needed if you're using authentication on your wireless connection. You say you're not planning to use security, so this isn't necessary. However, I'd highly recommend at least using a simple WPA2-PSK to lock down your connection, otherwise you might end up giving free Internet access at best, and at worst you might be giving access to company PCs and servers. If you want to further use an 802.1x or WPA authentication method, then yes, you can use an AP as a RADIUS server and WDS to improve authenticated roaming, but this is far more limited than using a Cisco ACS.
As for your other questions, yes, your APs can all be configured the same except for at least three parameters: IP address, channel, and hostname. Configure your static IP addresses on the AP's BVI1 interface. Don't place it on the Radio or Ethernet interfaces, because if either of these interfaces goes down you'll lose the ability to configure the AP, so it's best to use the BVI1 interface.
And yes, configuring a DHCP scope for your clients on your L3 switch is a good design, or you could also use your DHCP server on a different subnet by using the ip helper-address command on the L3 interface. I hope this helps! Let me know if you need help configuring any of this.
Merry Christmas!
Jeff -
Setting up Multiple SSID's & VLAN
I have a Cisco 1230 AP along with a Sonic Wall TZ 210 and a Linksys SFE 2010P switch. On my AP I have created 2 SSID's. and 2 VLAN's. The first SSID is being broadcasted and has WPA encryption on it for our Corporate USers. The Second SSID is a Guest SSID and too is being broadcasted. I can make a laptop connect to the 1st SSID, but for some reason the 2nd SSID nothing will connect to it. The first SSID is associated to VLAN1 and the 2nd SSID is associated to VLAN2. VLAN1 has WPA encryption on it. VLAN2 is setup as Open and no Encryption. Any ideas?
My next question is how to I configure traffic on this AP with the other equipment mentioned? On my sonicwall we have segmented port6 on it to be a different subnet from the corporate subnet. On the Linksys switch I have enable VLANS on port2 and port48 which are on VLAN2. All other ports are on VLAN1. The AP connects to Ports 2 on the linksys switch and port 48 connects to port 6 on the Sonic Wall. When a corporate user connects to SSID1 I want them to be able to connect to the Corporate subnet. When a guest connects to SSID2 I want them to connect to the segmented guest network to only have Internet Access.
Hope this makes sense!
Below is my config on the AP. I am really only familiar with the IOS web interface so if you can explain it using that I'd appreciate it.
AP_WLAN_Bakery
Home Exec Configure
------------------ show version ------------------
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8)JEB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 20-Jul-07 20:51 by dchih
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
AP_WLAN_Bakery uptime is 1 hour, 40 minutes
System returned to ROM by reload
System restarted at 10:52:05 -0400 Fri Oct 15 2010
System image file is "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision B0) with 15138K/1236K bytes of memory.
Processor board ID FOC0849218B
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from reload
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:12:D9:8B:09:93
Part Number : 73-8704-08
PCA Assembly Number : 800-23211-09
PCA Revision Number : A0
PCB Serial Number : FOC0849218B
Top Assembly Part Number : 800-23304-08
Top Assembly Serial Number : FTX0902R2V1
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-A-K9
Configuration register is 0xF
------------------ show running-config ------------------
Building configuration...
Current configuration : 2544 bytes
! Last configuration change at 12:07:29 -0400 Fri Oct 15 2010 by admin
! NVRAM config last updated at 12:07:29 -0400 Fri Oct 15 2010 by admin
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP_WLAN_Bakery
clock timezone -0500 -5
clock summer-time -0400 recurring
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 vlan-name VLAN_Corporate vlan 1
dot11 vlan-name VLAN_Guest vlan 2
dot11 ssid WLAN_Corporate
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 005740565C0C5C5F5C741F
dot11 ssid WLAN_HartKitGuest
vlan 2
authentication open
mbssid guest-mode
username admin privilege 15 password 7 <removed>
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid WLAN_Corporate
ssid WLAN_HartKitGuest
mbssid
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role root
no dot11 extension aironet
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.2.240 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
sntp server 192.168.2.5
sntp broadcast client
end
------------------ show stacks ------------------
Minimum process stacks:
Free/Size Name
4572/5500 soap_flash init
10024/11000 DHCP Autoinstall
5160/5500 Autoinstall
11748/12000 Setup
10552/11000 BootP Resolver
5240/5500 dot11 platform init
8824/12000 Init
5088/5500 RADIUS INITCONFIG
2576/3000 Rom Random Update Process
5144/11000 HTTP CP
3084/5500 Soap Flash Save Variables
Interrupt level stacks:
Level Called Unused/Size Name
4 125707 8056/9000 dot11 radio interrupt
6 9783 8960/9000 NS16550 VECTOR
------------------ show interfaces ------------------
BVI1 is up, line protocol is up
Hardware is BVI, address is 0012.d98b.0993 (bia 0013.1973.8d50)
Internet address is 192.168.2.240/24
MTU 1500 bytes, BW 54000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 10000 bits/sec, 9 packets/sec
5 minute output rate 10000 bits/sec, 4 packets/sec
59436 packets input, 8310033 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
31826 packets output, 18823451 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:15:20, output 00:15:20, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 47
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
16093 packets input, 1696312 bytes, 0 no buffer
Received 1913 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
8367 packets output, 2930004 bytes, 0 underruns
13 output errors, 0 collisions, 37 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0.1 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
Dot11Radio0.2 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
FastEthernet0 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 13000 bits/sec, 10 packets/sec
5 minute output rate 10000 bits/sec, 4 packets/sec
75878 packets input, 12726627 bytes
Received 43517 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
38986 packets output, 19917202 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0.1 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
FastEthernet0.2 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
------------------ show controllers ------------------
interface Dot11Radio0
Radio AIR-MP31G, Base Address 0013.1973.8d50, BBlock version 0.00, Software version 6.11.1
Serial number: FOC0901D4S1
Number of supported simultaneous BSSID on Dot11Radio0: 8
Carrier Set: Americas (US )
Uniform Spreading Required: No
Current Frequency: 2412 MHz Channel 1
Allowed Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11)
Listen Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11) 2467(12) 2472(13) 2484(14)
Beacon Flags: 0; Beacons are enabled; Probes are enabled
Current CCK Power: 100 mW
Allowed CCK Power Levels: 1 5 10 20 30 50 100
Current OFDM Power: 30 mW
Allowed OFDM Power Levels: 1 5 10 20 30
Allowed Client Power Levels: 1 5 10 20 30 50 100
ERP settings: short slot time.
Neighbors in non-erp mode:
Current Rates: basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Active Rates: basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Allowed Rates: 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Range Rates: basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Throughput Rates: basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Default Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Current Voice Rates: 5.5 6.0 11.0 12.0 24.0 [disabled until voice packet-discard enabled]
Default Voice Rates: 5.5 6.0 11.0 12.0 24.0
Channel / Max Power Table
1 O=15 D=20, 2 O=15 D=20, 3 O=15 D=20, 4 O=15 D=20, 5 O=15 D=20
6 O=15 D=20, 7 O=15 D=20, 8 O=15 D=20, 9 O=15 D=20, 10 O=15 D=20
11 O=15 D=20
Data Rate Sensitivity (rate, SNR dB, Contention dBm)
( 1.0, 1, -98) ( 2.0, 7, -94) ( 5.5, 9, -92) (11.0, 16, -86)
( 6.0, 7, -92) ( 9.0, 14, -87) (12.0, 12, -87) (18.0, 15, -84)
(24.0, 17, -82) (36.0, 24, -76) (48.0, 29, -73) (54.0, 33, -69)
Radio Management (RM) Configuration:
Regular AP RM Mode 1 Temp Setting Disabled
Temp Settings: AP Tx Power 0 AP Tx Channel 0 Client Tx Power 0
Rates:
Saved Settings: AP Tx Power 0 AP Tx Channel 1 Client Tx Power 0
Rates:
MCST RSCs: [0]0x0 [1]0x0 [2]0x0 [3]0x0 [4]0x0
TKIP Cum Stats: STA MIC-L-Errs MIC-R-Errs Replay C-Measure
0000.0000.0000 00000000 00000000 00000000 00000000
AES-CCMP Cum Stats: 00000000 replays discarded
QBSS Load: 0x0
Policing Stats:Rx downgardes 0, Tx downgrades 0
Configured Local Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 6 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 1 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 1 admission-control Off txop 1504
Configured Cell Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 10 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 2 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 2 admission-control Off txop 1504
Transmit queues: Active 0 In Progress 0
---- Active --- In-Progress --------------- Counts --------------
Cnt Quo Bas Max Cnt Quo Bas Sent Discard Fail Retry Multi
Uplink 0 0 0 0 0 0 0 0 0 0 0 0
Voice 0 0 0 0 0 0 0 55 0 0 1 1
Video 0 0 0 0 0 0 0 0 0 0 0 0
Best 0 3 70 3 0 3 24 7937 0 0 127 12
Mcast 0 0 0 0 0 0 0 329 0 0 0 0
Mcast 0 0 0 0 0 0 0 30 0 0 0 0
Back 0 0 0 0 0 0 0 329 0 0 0 0
BSSIDS Index Flags State Next Held Defer NonDefer Clients Tsf Dtim Txq
8D50 0 20 0 0 0 0 0 0 200 2 0
8D51 1 20 0 0 0 0 0 0 150 2 1
UP ClientQAged AcQAged PacketAged Drop Retry/Thresh Timeout CQMax
7 0 0 0 3/100 0/500 35 4
6 0 0 0 3/100 0/500 35 4
5 0 0 0 3/100 0/500 35 4
4 0 0 0 3/100 0/500 35 4
3 0 0 0 3/100 0/500 35 4
2 0 0 0 3/100 0/500 35 4
1 0 0 0 3/100 0/500 35 4
Driver TX blocks: in use 0, high 10, at reset 0, fail 0, reclaim 0
Clients: 8021x auth in prog 0 allowed 0
Vlan BSSID Clients PSP Pri Encr Key0 Key1 Key2 Key3 SSIDs
0 8D50 0 0 0 0 234 x128
1n 8D50 0 0 0 0 234 x128 WLAN_Corporate
2 8D51 1 0 0 0 0 WLAN_HartKitGuest
0 0 flags 3
1 1 flags 3
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
17 0 flags 0
18 0 flags 0
Registers: io E8000000 mem 80000000 aux A0000000
0000 FF50 0000 0000 0021 0000 0000 0000
0001 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0500 0007 0000 0000 0808 09E8 0000 0504
0000 0000 0000 0000 0424 0059 E2ED 2D9D
00000000 00000200 20000200 FFFFFFFF F7FFFFFF 00000000 00000000 00200000
FFFFFFE2 00000FFF 72ED14BD 4A040401 00000000 00000000 00008000 00008080
00000000 00000000 00000000 00000000 00008F78 000012DC 00000000 0000C0EA
Radio running: temp 0 C tx_power 100 bb_code 0x0
rssi_threshold 0x0 gain offset 0
Antenna: external , gain 20 (platform 0, domain class A)
PCI sys_id: 0xA506 subsys_id 0x5100 (0x5101)
Unicast ciphers 0x1 mcast ciphers 0x1
Rid Ring:
A0000970: 009C8000 20ED1EA0 * n
Rx Ring:
A0000950: 893E0002 20ED3478 v, 893E0002 20EDEE60 v
A0000960: 893E0002 20EE4B54 v, 893E0002 20EDB068 * v
Tx Ring:
A0000800: 06108000 20ECFCE4 n, 009A8000 20ECD764 n
A0000810: 00AE8000 20ECF064 n, 010C8000 20ECD124 n
A0000820: 010C8000 20ECCE04 n, 010C8000 20ECE0C4 n
A0000830: 010C8000 20ECED44 n, 00668000 20ECB174 n
A0000840: 006A8000 20ECCA64 n, 010C8000 20ECDDA4 n
A0000850: 010C8000 20ECF6A4 n, 01848000 20ECF9C4 n
A0000860: 022A8000 20ECCE04 n, 01848000 20ECF9C4 n
A0000870: 06158000 20ED113C n, 01848000 20ECE3E4 n
A0000880: 022A8000 20ECF064 * n, 01188000 20ECD124 n
A0000890: 05688000 20ED0A74 n, 057C8000 20ED03AC n
A00008A0: 010C8000 20ECED44 n, 010C8000 20ECDDA4 n
A00008B0: 010C8000 20ECF6A4 n, 010C8000 20ECF9C4 n
A00008C0: 00748000 20ECB054 n, 05FC8000 20ED1804 n
TxDn Ring:
A0000930: 802C0000 20ED26A0 v, 802C0000 20ED2778 v
A0000940: 802C0000 20ED2850 * v, 802C0000 20ED2928 v
Multicast counters:
Internal MC counts:
28 (28) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0)
Log Buffer:
PowerPC405GP Ethernet unit 0
PHY Hardware is Intel LXT971 rev. 2 (id_register: 0x13, 0x78E2)
rx_intr: 0 tx_intr: 0 mac_err_isr: 0 phy_link_isr:0
Current station address 0012.d98b.0993, default address 0012.d98b.0993
MAL register dump:
malcr 0x0007C082 0x180
malesr 0x00000000 0x181
malier 0x0000000F 0x182
maltxcasr 0x80000000 0x184
maltxcarr 0x80000000 0x185
maltxeobisr 0x00000000 0x186
maltxdeir 0x00000000 0x187
malrxcasr 0x80000000 0x190
malrxcarr 0x80000000 0x191
malrxeobisr 0x00000000 0x192
malrxdeir 0x00000000 0x193
maltxctp0r 0x00EE6120 0x1A0
malrxctp0r 0x00EE6020 0x1C0
malrcbs0 0x00000060 0x1E0
EMAC register dump:
emacmr0 0x18000000 0x00
emacmr1 0xA1788000 0x04
emactmr0 0x00000000 0x08
emactmr1 0x380F0000 0x0C
emacrmr 0x7D180000 0x10
emacisr 0x00000002 0x14
emacier 0x00000001 0x18
emaciah 0x00000012 0x1C
emacial 0xD98B0993 0x20
emacptr 0x0000FFFF 0x2C
emaclsah 0x00000040 0x50
emaclsal 0x2B637E9B 0x54
emacipgr 0x00000004 0x58
emacstacr 0x47808011 0x5C
emactrtr 0x18000000 0x60
emacrwmr 0x0F002000 0x64
emacoctx 0x0132EA47 0x68
emacocrx 0x00C72D8B 0x6C
UIC register dump:
uicsr 0x00001FA3 0xC0
uicer 0x803F0048 0xC2
uicmsr 0x00000000 0xC6
PHY register dump:
3100 782D 0013 78E2 01E1 41E1 0007 2001 0000 0000 0000 0000 0000 0000 0000 0000
0384 4780 0032 0000 0422 0000 0000 0000 0000 0000 08C8 0000 0000 0000 0000
RX ring with 16 entries at 0xEE6020, Buffer size 1528
Rxhead = 0xEE6048 (5), Rxp = 0xB67360 (5)
00 pak=0x0B6D644 buf=0x0EF2BDC status=9C00 pak_size=0
01 pak=0x0B6CCA8 buf=0x0EF17A8 status=9C00 pak_size=0
02 pak=0x0B68C98 buf=0x0EE90F8 status=9C00 pak_size=0
03 pak=0x0B6BCA4 buf=0x0EEF5FC status=9C00 pak_size=0
04 pak=0x0B6DFE0 buf=0x0EF4010 status=9C00 pak_size=0
05 pak=0x0B6CFDC buf=0x0EF1E64 status=9C00 pak_size=0
06 pak=0x0B6C640 buf=0x0EF0A30 status=9C00 pak_size=0
07 pak=0x0B682FC buf=0x0EE7CC4 status=9C00 pak_size=0
08 pak=0x0B6E648 buf=0x0EF4D88 status=9C00 pak_size=0
09 pak=0x0B6E97C buf=0x0EF5444 status=9C00 pak_size=0
10 pak=0x0B6ECB0 buf=0x0EF5B00 status=9C00 pak_size=0
11 pak=0x0B6ACA0 buf=0x0EED450 status=9C00 pak_size=0
12 pak=0x0B68630 buf=0x0EE8380 status=9C00 pak_size=0
13 pak=0x0B6D310 buf=0x0EF2520 status=9C00 pak_size=0
14 pak=0x0B6C974 buf=0x0EF10EC status=9C00 pak_size=0
15 pak=0x0B6B63C buf=0x0EEE884 status=DC00 pak_size=0
TX ring with 8 entries at 0xEE6120, tx_count = 0
tx_head = 0xEE6148 (5), head_txp = 0xB673BC (5)
tx_tail = 0xEE6148 (5), tail_txp = 0xB673BC (5)
00 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
01 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
02 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
03 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
04 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
05 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
06 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
07 pak=0x0000000 buf=0x0000000 status=5400 pak_size=0
0 missed datagrams, 0 overruns
0 transmitter underruns, 0 excessive collisions
0 single collisions, 0 multiple collisions
0 dma memory errors, 0 CRC errors
0 alignment errors, 0 runts, 0 giants
emac/mal specific errors:
0 rx in range, 0 rx out range
0 mal_rx_serr, 0 mal_tx_serr
0 mal_rx_de, 0 mal_tx_de
0 emac_int
0 mal_err_isr
0 SQE errors, 0 tx CRC errors
0 output queue fail
------------------ show data-corruption ------------------
No data inconsistency errors have been recorded.
------------------ show file systems ------------------
File Systems:
Size(b) Free(b) Type Flags Prefixes
* 7741440 2734080 flash rw flash:
- - opaque rw bs:
7741440 2734080 unknown rw zflash:
- - opaque rw archive:
- - opaque rw system:
32768 29138 nvram rw nvram:
- - network rw tftp:
- - opaque rw null:
- - opaque ro xmodem:
- - opaque ro ymodem:
- - network rw rcp:
- - network rw ftp:
- - network rw http:
- - network rw scp:
- - network rw https:
------------------ show flash: ------------------
Directory of flash:/
2 -rwx 1048 Oct 15 2010 12:07:29 -04:00 private-multiple-fs
5 drwx 512 Oct 15 2010 10:36:30 -04:00 c1200-k9w7-mx.123-8.JEB1
4 -rwx 716 Feb 28 2002 19:06:22 -05:00 env_vars
146 -rwx 2549 Oct 15 2010 12:07:29 -04:00 config.txt
148 -rwx 5 Oct 15 2010 12:07:29 -04:00 private-config
7741440 bytes total (2734080 bytes free)
------------------ dir nvram: ------------------
Directory of nvram:/
30 -rw- 2549 <no date> startup-config
31 ---- 5 <no date> private-config
1 -rw- 0 <no date> ifIndex-table
32768 bytes total (29138 bytes free)
------------------ show memory statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor A4AB84 4709500 2431436 2278064 1920552 2125904
I/O ECB000 1265664 468008 797656 727168 779580
------------------ show process memory ------------------
Total: 5975164, Used: 2899444, Free: 3075720
PID TTY Allocated Freed Holding Getbufs Retbufs Process
0 0 3373064 827724 1898920 0 0 *Init*
0 0 11804 7372856 11804 0 0 *Sched*
0 0 66125428 65999528 293168 434276 0 *Dead*
1 0 0 0 6416 0 0 Chunk Manager
2 0 188 188 3916 0 0 Load Meter
3 0 448120 443220 18392 0 0 HTTP CP
4 0 19548 0 25964 0 0 Check heaps
5 0 86364 207192 37368 49920 137052 Pool Manager
6 0 0 0 6416 0 0 AAA_SERVER_DEADT
7 0 188 188 6416 0 0 Timers
8 0 188 188 6416 0 0 AAA high-capacit
9 0 488 0 6904 0 0 SNTP
10 0 76 0 6492 0 0 ARP Input
11 0 3232 540 9108 0 0 Entity MIB API
12 0 0 0 6416 0 0 HC Counter Timer
13 0 188 188 6416 0 0 GraphIt
14 0 0 0 6416 0 0 Net Input
15 0 0 0 6416 0 0 Critical Bkgnd
16 0 19648 136 12180 0 0 Net Background
17 0 188 188 11916 0 0 Logger
18 0 188 188 6416 0 0 TTY Background
19 0 0 0 9916 0 0 Per-Second Jobs
20 0 188 188 6416 0 0 Compute load avg
21 0 0 0 6416 0 0 Per-minute Jobs
22 0 125880 59144 52956 0 0 Dot11 driver
23 0 188 188 6416 0 0 Dot11 driver log
24 0 0 0 6416 0 0 Voice Metrics Ta
25 0 0 0 6416 0 0 SOAP LED Process
26 0 188 188 6416 0 0 AAA Server
27 0 0 0 6416 0 0 AAA ACCT Proc
28 0 0 0 6416 0 0 ACCT Periodic Pr
29 0 2343100 10891400 16904 0 7173144 IP Input
30 0 0 0 6416 0 0 ICMP event handl
31 0 188 188 6416 0 0 AAA Dictionary R
32 0 47124 44272 9200 0 0 CDP Protocol
33 0 0 0 6416 0 0 linktest
34 0 964 964 9916 0 0 Dot11 aaa proces
35 0 0 0 9916 0 0 pmkid
36 0 188 6404 6416 0 0 Dot11 Mgmt & Ass
37 0 1636 1224 6644 0 0 AiroIAPP Protoco
38 0 188 188 6416 0 0 Triggered events
39 0 188 188 9916 0 0 Dot11 auth Dot1x
40 0 0 0 6416 0 0 Dot11 Mac Auth
41 0 1276 0 7692 0 0 Dot11CACprocess
42 0 0 1285716 11916 0 0 TCP Timer
43 0 0 0 11916 0 0 TCP Protocols
44 0 0 0 6416 0 0 Socket Timers
45 0 41144 11308 23364 0 0 DHCPD Receive
46 0 58666708 40499364 31400 6957504 101520 HTTP CORE
47 0 1072 188 12800 0 0 Soap Upgrade fet
48 0 10608 188 16836 0 0 DDP
49 0 344168 1754412 6416 0 0 LOCAL AAA
50 0 188 188 6416 0 0 AAA Cached Serve
51 0 188 188 6416 0 0 ENABLE AAA
52 0 188 188 6416 0 0 LINE AAA
54 0 2056 188 8284 0 0 TPLUS
55 0 604 188 9332 0 0 Crypto WUI
56 0 0 0 6416 0 0 EM Background Pr
57 0 188 308 6416 0 0 Soap Consoleless
58 0 72384 66968 14332 0 0 Crypto CA
59 0 0 0 8916 0 0 Crypto PKI-CRL
60 0 0 0 8916 0 0 Crypto SSL
61 0 2056 15044 6416 0 0 AAA SEND STOP EV
62 0 188 188 6416 0 0 Dot11 LBS Proc
63 0 0 0 6416 0 0 Syslog Traps
65 0 0 0 6416 0 0 DHCPD Timer
66 0 76 484 9992 0 0 DHCP Client
67 0 636960 188 22156 421308 0 HyBridge Input P
68 0 344 188 6588 0 0 Tbridge Monitor
69 0 344 188 6572 0 0 Spanning Tree
70 0 156 0 6628 0 0 DHCPD Database
2897284 Total
------------------ show process cpu ------------------
CPU utilization for five seconds: 16%/0%; one minute: 4%; five minutes: 1%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 0 1 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 4 1196 3 0.00% 0.00% 0.00% 0 Load Meter
3 369 40 9225 0.00% 0.00% 0.00% 0 HTTP CP
4 764 611 1250 0.00% 0.00% 0.00% 0 Check heaps
5 9 44 204 0.00% 0.00% 0.00% 0 Pool Manager
6 0 1 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
7 0 2 0 0.00% 0.00% 0.00% 0 Timers
8 0 9 0 0.00% 0.00% 0.00% 0 AAA high-capacit
9 8 158 50 0.00% 0.00% 0.00% 0 SNTP
10 1034 5268 196 0.00% 0.02% 0.00% 0 ARP Input
11 2 2 1000 0.00% 0.00% 0.00% 0 Entity MIB API
12 2 1494 1 0.00% 0.00% 0.00% 0 HC Counter Timer
13 2 5973 0 0.00% 0.00% 0.00% 0 GraphIt
14 0 11 0 0.00% 0.00% 0.00% 0 Net Input
15 0 1 0 0.00% 0.00% 0.00% 0 Critical Bkgnd
16 34 1906 17 0.00% 0.00% 0.00% 0 Net Background
17 4 101 39 0.00% 0.00% 0.00% 0 Logger
18 24 5969 4 0.00% 0.00% 0.00% 0 TTY Background
19 5 5998 0 0.00% 0.00% 0.00% 0 Per-Second Jobs
20 0 1196 0 0.00% 0.00% 0.00% 0 Compute load avg
21 433 127 3409 0.00% 0.00% 0.00% 0 Per-minute Jobs
22 587 181376 3 0.00% 0.00% 0.00% 0 Dot11 driver
23 0 2 0 0.00% 0.00% 0.00% 0 Dot11 driver log
24 2 1200 1 0.00% 0.00% 0.00% 0 Voice Metrics Ta
25 44 39944 1 0.00% 0.00% 0.00% 0 SOAP LED Process
26 238 3309 71 0.00% 0.00% 0.00% 0 AAA Server
27 0 1 0 0.00% 0.00% 0.00% 0 AAA ACCT Proc
28 0 1 0 0.00% 0.00% 0.00% 0 ACCT Periodic Pr
29 10607 39208 270 0.31% 0.16% 0.09% 0 IP Input
30 0 1 0 0.00% 0.00% 0.00% 0 ICMP event handl
31 0 2 0 0.00% 0.00% 0.00% 0 AAA Dictionary R
32 96 999 96 0.00% 0.00% 0.00% 0 CDP Protocol
33 2 5997 0 0.00% 0.00% 0.00% 0 linktest
34 14 115 121 0.00% 0.00% 0.00% 0 Dot11 aaa proces
35 1 100 10 0.00% 0.00% 0.00% 0 pmkid
36 116 2261 51 0.00% 0.00% 0.00% 0 Dot11 Mgmt & Ass
37 18 7228 2 0.00% 0.00% 0.00% 0 AiroIAPP Protoco
38 0 2 0 0.00% 0.00% 0.00% 0 Triggered events
39 0 2 0 0.00% 0.00% 0.00% 0 Dot11 auth Dot1x
40 0 1 0 0.00% 0.00% 0.00% 0 Dot11 Mac Auth
41 2 1200 1 0.00% 0.00% 0.00% 0 Dot11CACprocess
42 59 2009 29 0.00% 0.00% 0.00% 0 TCP Timer
43 0 1 0 0.00% 0.00% 0.00% 0 TCP Protocols
44 0 1 0 0.00% 0.00% 0.00% 0 Socket Timers
45 14 54 259 0.00% 0.00% 0.00% 0 DHCPD Receive
46 48468 30304 1599 9.35% 1.66% 0.36% 0 HTTP CORE
47 0 2 0 0.00% 0.00% 0.00% 0 Soap Upgrade fet
48 0 2 0 0.00% 0.00% 0.00% 0 DDP
49 707 3309 213 0.00% 0.02% 0.00% 0 LOCAL AAA
50 1 2 500 0.00% 0.00% 0.00% 0 AAA Cached Serve
51 0 2 0 0.00% 0.00% 0.00% 0 ENABLE AAA
52 0 2 0 0.00% 0.00% 0.00% 0 LINE AAA
54 0 2 0 0.00% 0.00% 0.00% 0 TPLUS
55 0 3 0 0.00% 0.00% 0.00% 0 Crypto WUI
56 0 1 0 0.00% 0.00% 0.00% 0 EM Background Pr
57 1 3 333 0.00% 0.00% 0.00% 0 Soap Consoleless
58 6 4 1500 0.00% 0.00% 0.00% 0 Crypto CA
59 0 1 0 0.00% 0.00% 0.00% 0 Crypto PKI-CRL
60 0 1 0 0.00% 0.00% 0.00% 0 Crypto SSL
61 3 16 187 0.00% 0.00% 0.00% 0 AAA SEND STOP EV
62 0 2 0 0.00% 0.00% 0.00% 0 Dot11 LBS Proc
63 0 1 0 0.00% 0.00% 0.00% 0 Syslog Traps
65 0 50 0 0.00% 0.00% 0.00% 0 DHCPD Timer
66 8 6027 1 0.00% 0.00% 0.00% 0 DHCP Client
67 8349 84826 98 0.55% 0.17% 0.10% 0 HyBridge Input P
68 14 6744 2 0.00% 0.00% 0.00% 0 Tbridge Monitor
69 0 2 0 0.00% 0.00% 0.00% 0 Spanning Tree
70 0 1690 0 0.00% 0.00% 0.00% 0 DHCPD Database
------------------ show process cpu history ------------------
AP_WLAN_Bakery 12:32:06 PM Friday Oct 15 2010 -0400
1133333
667777766666
100
90
80
70
60
50
40 *****
30 *****
20 *******
10 ************
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per second (last 60 seconds)
7 37 78 7 8
11 121961 87 1 3 1 1
100
90 *
80 ** *
70 * * ** * *
60 * * ** * *
50 * * ** * *
40 * ** ** * *
30 * ** ** * *
20 * ** #* * *
10 #*## ## # #
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per minute (last 60 minutes)
* = maximum CPU% # = average CPU%
8
8
100
90 *
80 *
70 *
60 *
50 *
40 *
30 *
20 *
10 *
0....5....1....1....2....2....3....3....4....4....5....5....6....6....7.
0 5 0 5 0 5 0 5 0 5 0 5 0
CPU% per hour (last 72 hours)
* = maximum CPU% # = average CPU%
------------------ show dot11 associations all-client ------------------
------------------ show wlccp ap mobility traffic ------------------
------------------ show wlccp ap mobility forwarding ------------------
------------------ show inventory ------------------
NAME: "AP1210", DESCR: "Cisco Aironet 1200 Series Access Point"
PID: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ, VID: ÿÿÿ, SN: FTX0902R2V1
------------------ Mempool statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor A4AB84 4709500 2431000 2278500 1920552 2125904
I/O ECB000 1265664 468008 797656 727168 779580
------------------ show memory summary -----------------
Processor memory
Alloc PC Size Blocks Bytes What
0x4790 0000000080 0000000001 0000000080 ACL Header
0x47A4 0000000024 0000000001 0000000024 Init
0x9FD4 0000000036 0000000001 0000000036 Init
0x9FFC 0000000040 0000000001 0000000040 Init
0xA018 0000000024 0000000001 0000000024 Init
0xA040 0000000036 0000000001 0000000036 Init
0xA134 0000000060 0000000001 0000000060 Init
0xF9D0 0000000024 0000000001 0000000024 HTTP CP
0xFAF8 0000000024 0000000001 0000000024 HTTP CP
0xFB6C 0000000076 0000000001 0000000076 HTTP CP
0xFC04 0000000024 0000000001 0000000024 HTTP CP
0xFC60 0000000028 0000000001 0000000028 HTTP CP
0xFD58 0000000024 0000000001 0000000024 Init
0xFDC4 0000000024 0000000001 0000000024 Init
0xFF2C 0000000036 0000000001 0000000036 HTTP CP
0xFF2C 0000000044 0000000001 0000000044 HTTP CP
0x11034 0000000024 0000000001 0000000024 Init
0x15750 0000004096 0000000001 0000004096 Init
0x1DD08 0000000120 0000000001 0000000120 Ion New Block
0x1F474 0000000024 0000000001 0000000024 LOGIN UNC PW
0x1F474 0000000056 0000000001 0000000056 LOGIN PWC (Free Blocks)
0x1F610 0000000080 0000000001 0000000080 local_aaa_authen2 (Free Blocks)
0x24F64 0000004784 0000000001 0000004784 (coalesced) (Free Blocks)
0x24F64 0000013956 0000000001 0000013956 (coalesced) (Free Blocks)
0x264F4 0000000512 0000000001 0000000512 Init
0x2CDF8 0000004312 0000000001 0000004312 TTY data
0x2E994 0000001500 0000000001 0000001500 String-DB entries
0x2E9BC 0000001500 0000000001 0000001500 String-DB owners
0x2E9E4 0000000776 0000000001 0000000776 String-DB handles
0x2E9FC 0000001024 0000000001 0000001024 String DB Hash Table
0x2F154 0000000024 0000000002 0000000048 SDB String
0x2F714 0000000176 0000000001 0000000176 SDB Owner info
0x2FF28 0000004312 0000000006 0000025872 TTY data
0x336E8 0000002000 0000000001 0000002000 TTY Input Buf
0x33720 0000000512 0000000001 0000000512 TTY Output Buf
0x3E6C0 0000000052 0000000003 0000000156 MAC ADDR subblock
0x40DA8 0000003000 0000000002 0000006000 keepalive sb chunk
0x42490 0000065536 0000000001 0000065536 Parseinfo Blocks
0x424B8 0000000364 0000000001 0000000364 tokenQ node
0x424E0 0000000432 0000000001 0000000432 Chain Cache Nodes
0x42508 0000032768 0000000001 0000032768 Parse Nodes
0x46E18 0000000120 0000000001 0000000120 Init
0x47028 0000000060 0000000001 0000000060 Init
0x47458 0000000024 0000000034 0000000816 Init
0x4755C 0000010000 0000000001 0000010000 Parser Linkage
0x47938 0000000056 0000000053 0000002968 Parser Mode
0x47938 0000000108 0000000001 0000000108 Parser Mode
0x479A4 0000000024 0000000054 0000001296 Parser Mode Q1
0x479C8 0000000024 0000000054 0000001296 Parser Mode Q2
0x49FA8 0000000432 0000000001 0000000432 Chain Cache No
0x4A070 0000000432 0000000009 0000003888 Chain Cache No
0x4A070 0000000432 0000000001 0000000432 Chain Cache No (Free Blocks)
0x4A070 0000000548 0000000001 0000000548 (coalesced) (Free Blocks)
0x4A160 0000000432 0000000001 0000000432 Chain Cache No
0x4FCD4 0000000256 0000000001 0000000256 HTTP CP
0x548F4 0000000032 0000000016 0000000512 Parser Alias
0x54924 0000000024 0000000016 0000000384 Init
0x5C338 0000004616 0000000001 0000004616 (coalesced) (Free Blocks)
0x5D464 0000000024 0000000001 0000000024 HTTP CP
0x5D4E4 0000000024 0000000001 0000000024 HTTP CP
0x65394 0000000024 0000000008 0000000192 Cond Debug definition
0x698F0 0000000068 0000000003 0000000204 GraphIt Data
0x6990C 0000001316 0000000003 0000003948 Graphit Client
0x69920 0000000024 0000000002 0000000048 Init
0x69920 0000000032 0000000001 0000000032 Init
0x73254 0000000164 0000000002 0000000328 Init
0x73278 0000000164 0000000002 0000000328 Init
0x7329C 0000000164 0000000002 0000000328 Init
0x7B12C 0000000164 0000000001 0000000164 Init
0x7B150 0000000164 0000000001 0000000164 Init
0x7B174 0000000164 0000000001 0000000164 Init
0x83E48 0000000060 0000000001 0000000060 HTTP CP
0x842C0 0000000044 0000000001 0000000044 HTTP CP
0x86C40 0000032772 0000000001 0000032772 Init
0x8AD2C 0000000024 0000000002 0000000048 AAA Secrettype
0x8AD64 0000000024 0000000002 0000000048 AAA Secrettype encrypt
0x8ADD0 0000000024 0000000002 0000000048 AAA_Secrettype pw
0x8B254 0000000192 0000000002 0000000384 AAA SG HEAD
0x8B294 0000000024 0000000002 0000000048 AAA SG NAME
0x8BFA8 0000000060 0000000001 0000000060 AAA MI SG NAME
0x8D1AC 0000003200 0000000001 0000003200 AAA attr list handle IDs
0x8DBA8 0000001024 0000000001 0000001024 AAA attr list handle IDs
0x9AE18 0000004096 0000000001 0000004096 AAA Unique Id Hash Table
0x9AED8 0000065536 0000000001 0000065536 AAA DB Chunk
0x9EFE8 0000020000 0000000001 0000020000 AAA Acct DB chunk
0xA0EA0 0000016336 0000000001 0000016336 AAA Acct Rec chunk
0xAFBC4 0000002048 0000000001 0000002048 AAA SG ID table
0xAFE78 0000001024 0000000003 0000003072 AAA SG ID table
0xB3D68 0000000032 0000000001 0000000032 Init
0xB4388 0000000024 0000000001 0000000024 AAA nvgend sg elt
0xB4388 0000000052 0000000001 0000000052 AAA nvgend sg elt
0xB43C0 0000000132 0000000002 0000000264 AAA Public Server Group
0xB4400 0000000028 0000000002 0000000056 AAA Public Server Group wrapper
0xB4448 0000000024 0000000002 0000000048 AAA pub SG servers
0xB44CC 0000000024 0000000002 0000000048 AAA pub SG wrap name
0xB4510 0000000024 0000000002 0000000048 AAA pub SG name
0xBC014 0000000776 0000000275 0000213400 *Free Packet Header*
0xBC014 0000000788 0000000001 0000000788 *Free Packet Header*
0xBC014 0000000804 0000000001 0000000804 *Free Packet Header*
0xBC014 0000000828 0000000001 0000000828 *Free Packet Header*
0xBC014 0000001408 0000000001 0000001408 (coalesced) (Free Blocks)
0xBC014 0000008480 0000000001 0000008480 (coalesced) (Free Blocks)
0xBCA88 0000000776 0000000003 0000002328 *In-use Packet Header*
0xC1274 0000004000 0000000001 0000004000 Packet Elements
0xC3B00 0000000184 0000000001 0000000184 IRB/CRB rxtypes
0xC3EE4 0000004712 0000000005 0000023560 *Hardware IDB*
0xC3EFC 0000001400 0000000005 0000007000 *Software IDB*
0xC4440 0000000024 0000000003 0000000072 HTTP CP
0xC4440 0000000076 0000000001 0000000076 HTTP CP
0xC4494 0000000024 0000000003 0000000072 HTTP CP
0xC4494 0000000080 0000000001 0000000080 HTTP CP
0xC4580 0000000184 0000000004 0000000736 IRB/CRB rxtypes
0xC4948 0000000048 0000000001 0000000048 HTTP CP
0xC4948 0000000052 0000000001 0000000052 HTTP CP
0xC4CB8 0000001400 0000000004 0000005600 *Software IDB*
0xC5864 0000000024 0000000004 0000000096 Init
0xC58E0 0000000024 0000000004 0000000096 Init
0xC8118 0000000032 0000000004 0000000128 IP Input
0xED1F0 0000035292 0000000001 0000035292 IDB List Element Chunks
0xFF3C0 0000000024 0000000059 0000001416 Init
0xFF7C4 0000000104 0000000008 0000000832 Init
0xFF7D4 0000000024 0000000006 0000000144 Init
0xFF7D4 0000000076 0000000001 0000000076 Init
0xFF7D4 0000000080 0000000001 0000000080 Init
0xFF8F4 0000000024 0000000001 0000000024 Init
0xFF9A4 0000000024 0000000007 0000000168 Init
0x102F38 0000010000 0000000001 0000010000 AAA chunk
0x103140 0000004616 0000000001 0000004616 AAA Acct AVLnode chunk
0x107F7C 0000000100 0000000001 0000000100 AAA MLIST
0x1081E8 0000000092 0000000001 0000000092 AAA MLIST
0x108A7C 0000001024 0000000002 0000002048 AAA mlist ID table
0x118430 0000001500 0000000007 0000010500 List Elements
0x119688 0000001500 0000000001 0000001500 List Elements
0x1196C8 0000005000 0000000001 0000005000 List Headers
0x11D7D4 0000001032 0000000001 0000001032 Process Array
0x11F5B0 0000000640 0000000068 0000043520 Process
0x11F5B0 0000000856 0000000001 0000000856 (coalesced) (Free Blocks)
0x1213A8 0000001500 0000000001 0000001500 Watched Semaph
0x1219A4 0000000144 0000000064 0000009216 Process Events
0x1219A4 0000000160 0000000002 0000000320 Process Events
0x1219A4 0000000172 0000000001 0000000172 Process Events
0x1219A4 0000000200 0000000001 0000000200 Process Events
0x1219A4 0000000208 0000000001 0000000208 Process Events
0x1219A4 0000000256 0000000001 0000000256 (coalesced) (Free Blocks)
0x1219A4 0000000432 0000000001 0000000432 (coalesced) (Free Blocks)
0x1219A4 0000000556 0000000001 0000000556 (coalesced) (Free Blocks)
0x123C24 0000001500 0000000001 0000001500 messages
0x123C50 0000001500 0000000001 0000001500 Watched messages
0x123C7C 0000010000 0000000001 0000010000 Watched Queue
0x123CA4 0000005000 0000000001 0000005000 Watched Boolean
0x123CCC 0000005000 0000000001 0000005000 Watched Bitfield
0x123CF4 0000001500 0000000001 0000001500 Watched Semaphore
0x123D18 0000005000 0000000001 0000005000 Watcher Info
0x123D40 0000000500 0000000001 0000000500 Watched Message Queue
0x123D68 0000001500 0000000001 0000001500 Watcher Message Queue
0x123D90 0000003000 0000000001 0000003000 Read/Write Locks
0x126050 0000002000 0000000001 0000002000 Reg Function 12
0x126078 0000001500 0000000001 0000001500 Reg Function iList
0x1260A0 0000001500 0000000001 0000001500 Reg Function Caselist
0x126118 0000002000 0000000005 0000010000 Reg Function 1
0x12657C 0000002000 0000000001 0000002000 Reg Function 1
0x129F50 0000000024 0000000002 0000000048 *Sched*
0x129F50 0000000032 0000000001 0000000032 *Sched*
0x129F50 0000000044 0000000008 0000000352 *Sched*
0x12A228 0000000256 0000000001 0000000256 Init
0x12C5F8 0000003000 0000000001 0000003000 CCA CCB chunks
0x12CDBC 0000000048 0000000008 0000000384 CCA Component
0x12CE24 0000000024 0000000007 0000000168 CCA Notification Flags
0x12CE24 0000000048 0000000001 0000000048 CCA Notification Flags
0x12CE84 0000003000 0000000008 0000024000 Keepalive
0x12CFF4 0000000024 0000000003 0000000072 CCA UserType
0x12D0A8 0000003000 0000000001 0000003000 CCA CLA chunks
0x1301C0 0000000024 0000000001 0000000024 TW Wheels
0x130200 0000016384 0000000003 0000049152 TW Buckets
0x13AA18 0000000112 0000000006 0000000672 Process Signals
0x13B01C 0000003000 0000000001 0000003000 Process Stack
0x13B01C 0000005500 0000000049 0000269500 Process Stack
0x13B01C 0000008000 0000000004 0000032000 Process Stack
0x13B01C 0000009000 0000000006 0000054000 Process Stack
0x13B01C 0000011000 0000000009 0000099000 Scheduler Stack
0x13B01C 0000018000 0000000001 0000018000 Interrupt Stack
0x13B01C 0002125900 0000000001 0002125900 (coalesced) (Free Blocks)
0x14F6BC 0000020000 0000000001 0000020000 Managed Chunk Queue Elements
0x151870 0000000068 0000000001 0000000068 (fragment) (Free Blocks)
0x1559A8 0000000296 0000000008 0000002368 Pool Info
0x155F84 0000000032 0000000001 0000000032 Pool Cache
0x15AF2C 0000000264 0000000001 0000000264 CLASSMAP_MODULE
0x15B7B0 0000000104 0000000001 0000000104 CLASSMAP_MODULE
0x15B8D0 0000000136 0000000001 0000000136 CLASSMAP_MODULE
0x15B8F0 0000000024 0000000001 0000000024 CLASSMAP_MODULE
0x15BA20 0000000024 0000000001 0000000024 CLASSMAP_MODULE
0x1826A8 0000000256 0000000001 0000000256 Init
0x182B78 0000000256 0000000001 0000000256 Init
0x1875C0 0000000776 0000000002 0000001552 *In-use Packet Header*
0x188DF4 0000000288 0000000003 0000000864 SNTP
0x188DF4 0000000332 0000000001 0000000332 DDP
0x1904D0 0000000776 0000000001 0000000776 *In-use Packet Header*
0x193CB8 0000001184 0000000005 0000005920 TCP CB
0x193CB8 0000000728 0000000001 0000000728 (fragment) (Free Blocks)
0x1A86AC 0000003000 0000000001 0000003000 IP Addresses
0x1AE490 0000000024 0000000004 0000000096 HTTP CP
0x1AE490 0000000032 0000000001 0000000032 Dot11 driver
0x1AE490 0000000048 0000000001 0000000048 AiroIAPP Protocol
0x1AE490 0000000068 0000000001 0000000068 HTTP CP
0x1CDDA0 0000000280 0000000004 0000001120 Init
0x1CDDAC 0000000068 0000000004 0000000272 Init
0x1EB928 0000005000 0000000001 0000005000 ip localpool
0x1EFFC4 0000000024 0000000001 0000000024 Init
0x1F9E40 0000001652 0000000003 0000004956 HTTP CORE
0x1F9EC8 0000000128 0000000003 0000000384 DHCPD Receive
0x1FBF20 0000000172 0000000002 0000000344 DHCPD Receive
0x1FBF20 0000000232 0000000001 0000000232 HTTP CORE
0x1FBF20 0000000500 0000000001 0000000500 (coalesced) (Free Blocks)
0x1FF2DC 0000000040 0000000001 0000000040 DHCPD Receive
0x206B78 0000000024 0000000003 0000000072 Init
0x206BA8 0000000024 0000000003 0000000072 Init
0x20BE88 0000001500 0000000001 0000001500 Syslogd Messages chunk
0x20FEF0 0000000024 0000000001 0000000024 Init
0x221B18 0000010000 0000000001 0000010000 Time Range Entry Chunks
0x221B40 0000003000 0000000001 0000003000 Time Range Item Chunks
0x221B68 0000001500 0000000001 0000001500 Time Range User Chunks
0x2221E4 0000000036 0000000016 0000000576 Init
0x222214 0000000040 0000000016 0000000640 Init
0x2233CCHi,
if you remove "encryption mode ciphers aes-ccm tkip" from the radio interface does it help?
it should remain like this:
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm tkip
ssid WLAN_Corporate
ssid WLAN_HartKitGuest
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.
Maybe you are looking for
-
How do I format a document in Pages 5.2 so that each sentence automatically starts with capital letter?
-
How to get the MAC address of the additional 10G NIC with ILO command line
how to get the MAC address of the additional 10G NIC with ILO command line? thanks. This question was solved. View Solution.
-
Assigning javascript array with jsp array
hi, I have a jsp page where I have a array in jsp. I want to assign the values to an javascipt array. how can I do that? the reason why I want to do this is for a perticular problem I am facing in javascript. that is.... I have a text box in my jsp p
-
Various Preferences not "sticking"
Having been a long time Mac user since the 80's starting with an SE, I have to say that I've never had so many problems with various preferences not saving after a major upgrade. It began with 10.4 with the annoying Finder views not saving my meticul
-
AE CS5 and CS5.5 crashes on a brand new machine
Hi, today I was so happy to install AE CS5 (as a part of the Master Collection) on my new Dell M6600, WIn 7 &4bit, Sp1 with i7-2920XM processor, 16 GB 1600 MHz RAM,SSD SATA III drive and.....the amazing 4 GB Quadro 5010M Obviously, I spent some mone