Same wlan both locally switched and centrally switched
Scenario:
1 virtual wireless controller
50 access points, some of them some local to the controller (same site), other on remote sites, all in flexconnect mode.
Is there a way for a wlan to be locally switched for a group of ap's, essentialy those local to the controller, and centrally switched for other groups of ap's, in fact those placed on remote sites?
I've tried configuring flexconnect groups, and ap groups, but no luck, I've found no way to override the globally configured flag "flexconnec local switching".
I've also tried to create two identical wlans, one locally switched and the second globally switched, but the wlc refuses to activate the second one since it has the same ssid of the first one.
Regards,
Massimo.
Since you have vWLC all AP needs to be in FlexConnect mode (If you got a normal WLC you can keep HQ AP in local mode & Remote AP in Flex mode to achieve this)
I think in your case you have to either choose "Central Switching" or "local switching" for your APs.
Regards
Rasika
**** Pls rate all useful responses ****
Similar Messages
-
In a Carrier Ethernet domain,Could someone please help me understand what's the basic difference between Access Switch and Aggregation Switch both in terms of s/w and h/w functionalities. MEF deals OAM,CFM, EVC provisioning only at the access edge switches. Do we need to repeat all these at the aggregation level? or is it just used for routing purpose? Do we have a separate Fault Management at the aggregation level?
Duplicate posts. :P
Go here: https://supportforums.cisco.com/discussion/12137156/what-are-major-differences-between-access-switch-and-aggregation-switch-wrt -
Core switch and sub switch gateway
I have a Layer 3 core switch(backbone) 10.18.16.0/24, and the core switch needs to connect to multiple Layer 2 sub switches.
The Layer 2 sub switches will connect to multiple workstations. The sub switches network will be 172.20.10.0/24, 172.20.40/24 and so on.
I use core switch IP 10.18.16.11 to connect to sub switch 172.20.10.0/24. Which gateway IP should I use for 172.20.10.0/24 ? Should I use 172.20.10.1 or 10.18.16.11 ?
Thank you for your help in advance.I am not sure what you mean by "sup switches", but usually you need a management IP/vlan segment, so you can use it to access the devices. So if your management segment is 172.20.10.0/24 you assign an SVI to every layer-2 switch and give it an IP in this range and the gateway for all the SVIs should be on the core (172.20.10.1/24
example:
access switch-1 172.20.10.11/24
access switch-2 172.20.10.12/24
access switch-3 172.20.10.13/24
and so on
The default gateway for all your layer-2 switches should be the SVI on the core (172.20.10.1/24)
HTH -
Help me to choose Right Core switches and Edge switches as per my Spec
Dear All
Please help me to choose Core and Edge switches and all required hard ware and software.
the spec details as per below
Core Switches
1. High performance, highly scalable core switch to provide multi-10GE connectivity to various segments in the network.
2. Switch should have redundant switch fabric and routing engines or management / supervisor modules
3.should have separate control and forwarding planes
4.Each switch should have redundant power supplies in N+N or N+1 fashion
5. Must allow for two spare slots once services, management, processing modules and line cards populated
6. Easy to manage firmware- i.e. single code type enterprise/service provider) or train, and robust operating system
7. Supports for the VRRP, NSR, GRES, BFD, STP, MSTP, RSTP, VSTP, LACP redundancy protocols
8. Hot plugging and removal
9. The switch should have native switching architecture with up to sufficient performance such that the loss of one switching fabric should not lead to degraded performance
10. Switch should support switching at least 400Mpps
11. Switch should be able to support 40 10Gig line rate ports in a fully redundant configuration
12. Chassis that can scale to 700 Gbps
13. The proposed Backbone switch should support, but not be limited to the following Layer 3 features:
Static ip routing
Routing information protocol (RIP) and RIP2
Open shortest path first (OSPF)
IGMP v1, v2 and v3
IGMP Snooping
IP multicast routing protocol
14. The switch should support the following features at a minimum:
Spanning Tree 802.1D, 802.1S, 802.1W
GVRP
802.1x single and multi-supplicant: VLAN and ACL assignment
Dynamic ARP Inspection (DAI), DHCP snooping, IP Source gurard
LLDP, LLDP-MED
802.3X, 802.3ad
Redundant Trunk Group (RTG)
IGMP snooping
Unicast static, OSPF v1/v2, RIP v1/v2
Multicast IGMPv1/v2, PIM
Graceful Route Engine SwitchoverI have gone through your document and I am surprised to see MORE information in the document than what you've posted. I am so mildly suspicious about the authenticity of the document and spreadsheet you've attached.
So far, based on this document, the client wants a chassis that can support up to 700 Gbps backplane. The only candidate, other than a full-blown Nexus solution, is the 6807-X.
Next, the document also states dual supervisor card with two spare slots. Good luck trying to get that much empty space on a 6807-X. This means 6509E. You can't use a 6513E because of line-card-to-slot limitation.
If you look under the heading "Edge Switching", the first sentence already makes references to 6800ia switch.
There's also a reference stating that the product should have a 100 Gbps backplane. You can take the 6509E chassis out of the equation.
So you see, I am suspicious about the authenticity of the document. I agree with mali's and devil's recommendation that if you are serious, you would be engaging Cisco SE/AM in your region. There are only three reasons, that I can think of, why you've posted this here. One of them is the intended purpose of this document (and the audience). -
I'm currently configuring a mass of new switches, and instead of doing them one by one, I was hoping someone has a better/faster solution. I have config files to use, and a laptop. Kind of limited on tools. Can anyone point me in the right direction?
You might want to look at something like "WINBATCH" or "expect" scripting.
The main issue, as pointed out in the first response, its that you need console connectivity to begin with, then you can either blow the rest of the config in through Ethernet, or set up a TFTP server with a default image and load 'em up from there.
You may want to do 'em in batches: first set the addresses up either manually or through a scripting progran (we read the configs from an Excel spreadsheet) to set up the common portions of tehe config, then blow in the config differences in a separate script/process.
The other upside to doing that is you can have some spares with the base config, then if you need to replace a switch later, you only need to add the "delta" config.
If you have a term server around, and are pretty clever with scritping (or the program (free) "expect") you could do a batch of 8, 16, or 32 at a time.
You may also be able to use some of the scripting facilities of CiscoWorks if you are using that.
Sounds like fun. We had to do a batch of 3000 Chipcom switches once. From that, a full-blown staging system was developed.
Good Luck
Scott -
Hi,
Can we still change Local SLD to Central SLD after the installation has been done?
Rgds,
Hapizorr Rozi AliasHello Rozi/Naveen,
Yes u can change the SLD configuration from central to local or a vice versa...
Please check the following SAP Note for u r ready reference
Note 720717 - Reduce the number of System Landscape Directories (SLD)
If usefull then give reward point..
Thanks -
Wlc flexconnect wlan local authentication and central web authentication maximum rtt
Hi
From the below link below it mentioned that "Round-trip latency must not exceed 300 milliseconds (ms) between the AP and the controller. If the 300 milliseconds round-trip latency cannot be achieved, configure the AP to perform local authentication."
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ch7_HREA.html#wp1094148.
Is this limitation refer to web authentication also?
Thanks
Anyone???Central Web Auth (CWA) works different on controllers/APs running in FlexConnect mode. Please check this guide and confirm that you have similar setup.
http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/116087-configure-cwa-wlc-ise-00.html
If so, please post screen shots with your configs (Redirect ACLs, policies in ISE and the WLC SSD settings).
Also, the version of code that you are running in ISE and your controller.
Thank you for rating helpful posts! -
3750 switch and HP switch fiber connectivity issue
I have connected 2 Cisco 3750 switches "WS-C3750-48TS-S" with the LC to LC Duplex Single Mode fiber cable. Both the switches are communicating with each other.
As i have checked in the cisco document that GLC-SX-MM support only Multimode fiber cable. So i am surprised how does it support single mode fiber optic cable.
Can anyone tell me the reason for supporting single mode fiber optic cable?
But when i connect HP 4208 switch with the same Cisco 3750 the interface is showing up but the input packets are 0 and output packets are increasing on both ends.
I have checked the SFP's and fiber cable are compatible with HP.
Can anybody suggest me what can be the possible cause of this?
Regards,
Mukesh Kumar
Network Engineer
Spooster IT ServicesI tried to troubleshoot this issue by using some show commands.
As i have checked that there are some specific commands to check SFP transreceiver as given below:
show hw-module subslot slot/subslottransceiver port idprom.
show interfaces {{[int_name] transceiver {[detail]} | {transceiver [module mod] | detail [module mod]}}
But these commands support only those transreceivers which support DOM. GLC-SX-MM doesn't support DOM.
Can anyone tell me that are there some troubleshoting commands to solve out the issue?
Regards,
Mukesh Kumar
Network Engineer
Spooster IT Services -
I have a slot machine app that I have played for a long time and have gotten to a very high level. I just recieved a I- pad Mini and when I downloaded the app on the Mini it started me back at the first level. Can I have in the mini the same level achieved on my phone?
Both iPhone and iPad mini using same Apple ID?
If yes use Game Center to launch game. First use on the IOS device containing the correct data by....
1. Open Game Center
2. Games at bottom screen
3. Select Game
4. Note ... Top right screen
5. Tough then play
Hopefully that work for you.
Game Center manages data across devices. -
Need help in setting up Group Policy for same user in local system and Terminal server
Hi All,
Currently our remote users are using our network using VPN client over internet.
They are generally at their home computer and doing VPN as they have to work only in one RDP server for application.
We actually have a OU created for these RDP users and assign then some strict policy like they can not use any other .exe,they can not user any explorer ,they can not even use windows explorer when they are on RDP they just use one exe of their application.
Now what my management want is they want their home computers in Domain and want them to login via their same credentials they are using for RDP but they don't want them to restrict in their home computers with any strict policy.
Now my confusion is how can I configure different policies for same users or same OU.
Can any one guide me please...you can achieve this fairly easily with group policy.
create an OU and put your remote desktop servers in that OU.
configure both user and computer policies in a group policy and link it to that ou.
you need to enable loopback mode - you may want it in merge or replace depending on your other policies you have. Probably replace though I would guess. this is set in the computer configuration > admin templates > system / group policy section.
now remove the policy you have currently setup for your users on the users OU containing the rdp users. If you want you can move these users back to your main users OU.
when your users login to the RDP server the settings in the user section of the GPO linked to the RDP Servers OU will apply.
when the user logs in to their own computer the policies from the user OU and computer OU will apply - but not the more restrictive RDP OU.
hope that makes sense.
Regards,
Denis Cooper
MCITP EA - MCT
Help keep the forums tidy, if this has helped please mark it as an answer
My Blog
LinkedIn: -
Diffrence Between Local IE And Central IE
Hi All,
What is the difference between the local Integration Engine And the Central Integration Engine ???
Please Explain me
Regards
VamsiThe systems on which SAP WAS is installed has Integration Engine as one of its components. Now for PI/XI also WAS is a must. Therefore PI/XI also has an Integration Engine called as Integration Server.
Now talking in terms of PI/XI, Integration Server has Adapter Engine, Integration engine (for pipeline steps) and Business Process Engine. This Integration Server is the central Integration Engine.
The Integration Engine of other systems is termed as local Integration Engine
Regards,
Prateek -
How to switch and maintain switched
Hello,
I have to switch in "true" an indicator using an OK botton. I want that when i push the botton for the first time my indicator becomes "true" and remains "true" forever independently from the OK botton status... How can i do?
Thanks in advance
GM
Solved!
Go to Solution.Something like this?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
Latch ON.png 12 KB -
I have a lot of photos in my trash bin and was thinking about emptying the trash. However, I got a message that said that if emptied, I would not be able to recover them. I chickened out. I looked at several pictures in the trash and noticed that they were the same pictures in albums that I had created. I compared the numbers shown on those pictures in the trash and found that they were the same as the numbers shown in on the pictures in the albums that I had created. I would like to delete the pictures to create more space, but I don't want to lose pictures that I can't replace.
yes - albums are not copies or places - they are pointers in the databae pointing to the photo in the library - you can see it in an album, under photos or under events - but it is all the same photo - if you delete it it is gone everyplace - and no additiponal space is used for an album (or many albums - a photo can be in many albums without using any additional space
Only put photos that you do not want to keep in the trash
How much free space do you have on the disk volume that the iPhoto library is on?
LN -
How to work on same project both in studio and on the road?
OK, so I do all my work on a macbook pro. My home setup includes an array of external hard drives but I would like to work on my project while Im traveling this weekend.
My project has several different sequences...SO, how can I export all material from one sequence on to a portable firewire drive, work on it on the road(same computer,different drive), then once back home continue where I left off with my normal drives back on line?
I don't want to export ALL the scratch disk due to size, just what's being used on a particular sequence.
Is this scenario possible? I assume I will use "media manager" and I assume if I do ANY rendering that those clips will need to be transfered back to original drives from the portable?
Ideas?
Thanks so much, I really enjoy this forum!Can't be done. If you media manage only the footage used in the cut, edit, then try to link your sequence to the full sized footage, it won't. FCP looks at REEL, TC start and stop and duration. If anything doesn't match, then it won't connect. If you want to edit on the road, you either need to bring a copy of the FULL clips used in the sequence (an option in the Media Manager COPY function...just don't choose DELETE UNUSED MEDIA), or you can RECOMPRESS (again, in MM) all the the footage to a smaller size (offline RT) and edit that. Then reconnect to the full res version when you come back.
Shane -
How can I match my apple ID for itunes and my apple ID on my cellphone?
Do you have multiple accounts or have you updated your account on your computer's iTunes and the update hasn't copied over to your iPhone ? If you've updated your account then tap on your id in Settings > iTunes & App Stores on your phone and log out of it and then log back in with the updated version.
If you have multiple accounts then you can log out of your account on your phone as above, or your computer's iTunes via the Store > Sign Out menu option, and you can then log in with the other account. But all content is tied to the account that downloaded it.
Maybe you are looking for
-
Error 1172, an error running a VI in the second time call of the DLL
Hello All, I am a beginner in labVIEW. I have to write a test program in labVIEW which uses a DLL created by other programmer. I called the DLL from my labVIEW to control DIOs, a serial port, communicate with a slave device, perfrom a flashing task.
-
Itunes has separated my music by album and by artist
how do I get albums all together? I have tried checking the "compilation" box but it has made no difference.
-
Video does not play on external plasma monitor
Forum Here is my situation. I received footage captured with a Panasonic HVX-200, the specs are: 29.97fps, Compressor: DVCPRO HD 720p 60, frame size: 960x720 I use an Intensity Pro video card for monitoring on a 42" Samsung LCD. When the Intensity Pr
-
Vendor Ref No. does not show in Journal Entry for AP Credit
AP Invoice journals show the vendor reference number in field Ref 2. However, when creating an AP Credit memo, the vendor reference number does not show in the journal for the credit memo, instead the field Ref 2 is used for the base document number
-
How to give Container Elements for FM EWW_WORKFLOW_START
hi experts, i am new to workflow, i am using the FM EWW_WORKFLOW_START to start a workflow. my issue is that i am using the std BO BUS2017 i am not getting the element name that i need to pass to the container. When i see in SWDD it shows Import Para