Sample rate off the audio input and out devices do not match - what to do?

This is fundamental, I know, but nevertheless I can't find my way around it. I get this error message when trying to recor:
Sample rate off the audio input and out devices do not match
and am asked to do this:
Use the appropriate operating system or audio device control panel to adjust the sample rates of the input and output devices to use the same settingt.
I have defined the sample rate to 44.1/16 bit in accordance with my inbuild soundcardt.
I am trying to record from LineIn.
When running on a M-Audio sound card I don't face any problems.
HP 8560W, sound card IDT/High definition audio Codec
Any suggestions?
Knud
Copenhagen

You're sure you have set BOTH the input and output settings to 44.1 16 bit?
Which version of Windows are you running? There are a number of posts on this forum about how to fully access both the Windows Mixer and the Mixer for your soundcard. Especially, you need to ensure that all "Windows Sounds" are turned OFF.

Similar Messages

The sample rates of the audio input and output devices do not match.

I am trying to record line-in audio and keep getting this error. have a realtek sound card. I have tried everything I know but cannot record. please help if you can, thanks.

Setting the Sample Rate in Windows Vista and 7

I'm trying to record in Adobe Audition and it keeps saying my the sample rates for my input and output devices do not match. How do I correct this?

I'm trying to record in Audition and it keeps saying my sample rates for the input and output devices don't match. How do I fix this?

I finally have communication between the ISA One and Audition. I moved the optic cable to another SPDIF on the computer and from the SPDIF to ADAT on the ISA One and it finally agreed that the communication was at the same clock speed. The audio was not intelligible so I moved the optic cable back to the original configuration and I can record voice that is clean.

CS6 will not accept my condensed mic stating; 'the sampole rates of the audio input and output do not match. Audio cannot be recorded until this is corrected. Use the appropriate operating system or audio device control panel to adjust the sample rates

!

The first things we need to know in order to be able to help are what are your operating system and audio device?
Also the FAQ Setting the Sample Rate in Windows Vista and 7 may help.

Print to Video Error msg: audio and vide devices may not match

When I attempt to print to video (using a Sony DV deck that has werved me well for years) I receive the message:
"The selected audio and video devices may not match:
-Apple FireWire NTSC (720 X 480)
Please verify that the audio and video outputs are externally routed to the intended device(s).
Do you want to proceed?"
I tried proceeding, and the video images output to the tape but without a sound track.
What to do? I must deliver a tape to my client!
I recently did a software update to 10.4.6. Could that be part of the problem?
Of did some setting change somewhere without my knowing it, and I need to reset it, if so what?
Thanks in advance

Hello!
Thank you for this. I did check the audio playback settings and it was NOT set to audio follows video. I then CHANGED it as you have kindly instructed. The audio video settings box you mention was NOT checked, so I didn't need to do anything there.
I then tried o launch Print to Video (not Edit to Tape) and sadly, the same error message occurred. Any suggestions would be much appreciated.
I am running FCP 4.5, recently upgraded to OS 10.4.6
Thanks in advance.
Hey Pamela,
Have you been monitoring externally this whole time?
If you have, and you've been getting external audio
and video, then this is probably a case of a
setting being off somewhere.
First, check your View > Audio Playback
setting. It should be set to Audio follows
Video.
Second, press Option-Command-Q to bring up the
Audio/Video Settings dialog. Click on the right-most
tab (A/V Devices) then confirm that the box for 'Use
Different output for Edit To Tape/Print To Video' is
not checked.
And please confirm that you're doing a Print to Video
and not an Edit To Tape. I ask because the only time
that I can remember getting this message is when I've
tried to do an Edit To Tape and didn't drag the
correct sequence from the browser (if I remember
correctly, I accidently dragged a sequence that was
also open in timeline).

Selected audio and video devices may not match

Hello - I was able to Print to Video w/no problem, from my Mac Book Pro, to my Panasonic PV-GS320 w/no problem. Now, all of a sudden, when trying to do this, I get this msg.:
'The selected audio and video devices may not match. Please verify that the a/v outputs are externally routed to the intended device(s).'
Not sure what happened, or what changed, but here is my setup:
Sequence & Capture Presets are both: DV NTSC 48 kHz
Device control preset: FireWire Basic
Video Playback: Apple Firewire NYSC (720 x 480)
Audio Playback: Default
Like I said, I don't know what got changed, but, it was working before - hope someone can help, thanks so much!!
Kristina

I think I found the problem...I had forgotten to switch my Device Control Preset back to FireWire, from the previous non-controllable - thanks so much!
Message was edited by: Kristina Latour
Message was edited by: Kristina Latour

How can I get my audio input and output devices back? I have no sound and cannot see any of the devices in Audio MIDI Setup..??

Hi, I tried to set up a new output audio device on my mac that would have multiple outputs (iBox Twist speaker and my internal speaker) but when I went to click onto one of the iBox Twist (there were 2 options available: iBox Twist and iBox Twist Stereo), Audio MIDI Setup crashed and when I finally got that back open, I found that there were no audio input or output devices to be found. My sound is working, as when I turn on my iMac, the starting sound still plays, however the volume control in the menu bar is no longer a black colour, but grey and when I try to change the sound on my keyboard it does not change. This already happened to me once, and after 3 hours I managed to fix it very simply (switching off Mac, unplugging power cord, leaving for 15 seconds, plug power cord back in and switch Mac back on, holding Alt, Cmd, P and R keys until you hear the Starting Up sound twice) however this same technique that fixed it once before is not working this time and I am still stuck without sound. I have tried Repair Permissions, rebooting in Safe Mode, Hardware Test and checking for Software Updates. Has anyone else had this problem and managed to fix it?
Thanks in advance for any help anyone can give me!

In case anyone has had the same problem as me, I have just managed to fix this by doing the following:
Switch off Mac
Switch back on in Safe Mode (Hit power button, then hold Shift key until a loading bar appears at the bottom of the screen).
Switch off Mac again
Remove power cord and wait 15 seconds
Plug power cord back in and hold down the keys alt, cmd, p, r all at the same time until you hear Starting chime for a second time and hopefully your audio will back.

Project sample rate vs the audio interface clock

I used Audition for digitizing archival audio and I mostly work in 96 kHz because it's the current archival standard for analog audio, however I occasionally need to transfer DAT or ADAT tapes at 44.1 or 48 kHz. One thing I noticed when I went to change the project format was that my audio interface clock did not change and match the multitrack settings. I was able to change the clock manually but I had to go to the Audio Hardware preferences.
I find this behavior for a DAW very strange. If I have a multitrack open of one bit rate and my clock set to another, how does that work? How does Audition 6 play and record audio at differnt sample rates than the interface clock? When I open a multitrack that's 96 kHz and my clock is set to 48, what sample rate am I getting? The audio file being saved says 96 kHz but is it?
Audition 6
RME Fireface UCX
Mac Pro mid-2010

loneraver1 wrote:
If true, this is indeed strange. I have used just about every DAW under the sun for the last 10 years based on what my employer purchased and I have never seen a DAW allow you to record sample rates where the project didn't match the incoming clock.
There should be an option that locks the audio interface internal clock to the opened project. It makes it annoying any time I have to switch between recording in 96 kHz to 48 kHz. That's annoying on it's own right, but what's really annoying is that it's an extra step that I have to train our archival technicians who don't have a techical background in audio.
I can definitely say it's true for my set-up!
Surely, the "extra step" you refer to is not necessary if AA is resampling the audio to match the desired sample rate?
As for the "option" to "lock the audio interface clock to the opened project", for those cards, like mine, which cannot have their sample rate changed by the audio software, how is that going to work? I suspect this was how AA CS5.5 and earlier worked: unless session/project and interface sample rate matched, no audio. I much prefer the current "resampling" method; no necessity to have to think about soundcard/interface settings every time a different sample rate is being used.
FWIW, if I want to record something at 44.1 I always ensure the card and AA settings are 44.1; but for "playback" (or video editing which I do quite a lot of and which requires 48 - my video editor software will not "play" unless the audio sampling rate of the card is 48 - ) 48 is my "default" setting.
JMO!

The audio port on my Imac is not working,what can i do to fix this?

When i tried to plug in my new Bose speaker in the audio port of my Imac, it is not working, i also tried regular headphones, and it is not working either, is there anything i can do to fix this?

1. Reset PRAM. http://support.apple.com/kb/PH14222
2. Reset SMC. http://support.apple.com/kb/HT3964
Choose the appropriate method.

HT1414 i wanted to reset my iphone from the phone settings and i started with no problem but now my i phone got stuck i can only see the apple logo and my phone does not start what to do please help

i wanted to reset my iphone 4 from the phone settings and everything started okay until i realised it was not working at all now my phone is tuck with the apple logo and won't start can not connect to the itunes store as well what to do please help

Place your iPhone into recovery mode as described here. You may have to try to enter recovery mode more than once to succeed.
http://support.apple.com/kb/HT1808

I have just installed CS6 Master collection but indesign isn't working, when opening I get the message "Cannot load Assignment UI.InDesign because it requires Username. Please install the Username plugin and restart InDesign." not sure what to do next?

I have successfully installed the CS6 master collection and all the programs seem to be working apart from InDesign. When opening it I get the message "Cannot load Assignment UI.InDesign because it requires Username. Please install the Username plugin and restart InDesign.". I have no idea what to do next?

Many people use a font manager to organize a large collection of fonts, and sometimes these cause problems in ID. You might not realize that the font manager has installed a plugin in ID, but I think you would know if you added any other program extensions to help you work.
Can you show us a new crash report since the 8.0.2 update?
What happens if you start the Mac with the Shift key held down to prevent extensions from loading? What happens if you go to the System settings and create a new user, then restart the Mac and log in with the new user?

Input and Output encoding do not match

My input xml file's encoding is "ISO-8859-1".After manipulating the contents using DOM and transforming , the encoding of the Output xml file is changed to "UTF-8".
Here is the source code:
public static void main(String args[])
try {
InputStream xml_utf = new FileInputStream("C:\\backup\\07_23\\input_1.xml");
InputSource inputSource = new InputSource(xml_utf);
DOMParser parser = new DOMParser();
try {
parser.parse(inputSource);
} catch (SAXException e) {
e.printStackTrace();
} catch (IOException e) {
e.printStackTrace();
Document doc = parser.getDocument();
Source source = new DOMSource(doc);
Result result = new StreamResult(new FileWriter("C:\\backup\\07_23\\output_1_input2.xml"));
Transformer xformer = null;
try {
xformer = TransformerFactory.newInstance().newTransformer();
xformer.transform(source, result);
} catch (TransformerConfigurationException e) {
e.printStackTrace();
catch (TransformerException e) {
e.printStackTrace();
How can I set the encoding of the output back to "ISO-8859-1"?
Thanks.

transformer.setOutputProperty("encoding","ISO-8859-1")
did the job...

Audio Line-in input and BT Headset output not working

Hi,
I'm trying to run the Line-in into my MBPro and route the output to my Logitech H800 BT Headphones at the same time (a pass through), but can't get it to work.
I have tried to run the line-in to the Internal Speakers and can not get this to work either.
Steps to taken:
1. Go to the Sound window by selecting the Sound icon from System Preferences.
Next, I route the Line-in by:
2. Selecting the Input button from Sound Effects, Output, Input buttons.
3. Select "Line In" from the Select a device for sound input list.
4. Select "Sound Input" from the Use audio port for drop down list
5. you should see activity on the Input Level.
6. Next, select the Ouput button from Sound Effects, Output, Input buttons.
7. Select "H800 Logitech Headset Stereo (or Internal Speakers) from the Select a device for sound output list.
8. Verify that "Sound Input" from the Use audio port for drop down list is still selected.
9. Also, verify that the Mute checkbox is not selected in either the Input or Output window.
10. NO SOUND :-(
11. If I pull up a radio station in a webbrowser, I can listen to it without issue. So, I think audio out is set correctly.
12. If I install Audacity: 1) It shows the audio input and output to be set as above (Built-in Input/H800 Headset). 2) If I record and then playback, it records the audio going in the Line-In and plays back accross the H800. 3) Also looked for a Monitor function in Audacity but could find one to test simulataneous I/O.
Any idaes welcome ?

ahh sry, thats how the line in works on my Mac Pro, I guess the Macbook is different. This is a program I use in conjunction with another called 'soundflower' to route my audio to all the places it needs to go:
http://www.macupdate.com/app/mac/11333/linein
If you need to run multiple instances, you can open up terminal and type
open -n /Applications/[PUT PROGRAM NAME HERE].app/
It will open up another instance every time you run that script.

Audio input and output

I am trying to get audio to play through from the audio input to the audio output. I have plugged a line-level keyboard into the audio input and as I play it, it shows that it has plenty of input level in the sound panel of the system preferences. However, there is no sound coming out. I have tried speakers, headphones and the Griffin IMic. If I use a program like SoundStudio3 and click the audio "thru" button it works fine, but it does not work without.
Is there a THRU switch that I am missing somewhere? I tried the Applications/Utilities/AudioMIDI setup to configure it, but the Thru button at the bottom is greyed out (not in operation).
Thanks.
2 GHZ intel core duo Mac OS X (10.4.8)

Hi Rich,
Welcome to apple forum.
In my opinion, I don't think OS X have the capability to sent the audio input "THRU" to output directly (I could be wrong).
You need to use Garage band or third party software like you mention before to allow it.
Maybe if you connect third party device that is "supported" the signal become audible and you can hear it. Like mBox using core audio driver.
http://www.apple.com/macosx/features/coreaudio/
Good Luck.

Audio IN and OUT messed up - how to diagnose??

I've got a weird issue and wondering if anyone can help. I have a Mac Pro and yesterday got a good mic and a pre-amp for my son to do some recording on GarageBand. I also installed the CuBase software that came with the pre-amp. The audio in and out is very erratic. Sometimes it will record, and sometimes not. And it will not playback properly (yes, I double-checked my Output/Input settings in System Preferences).
The same problem is happening on the CuBase software (which is GarageBand on steroids).
HOWEVER, when I fire up iTunes, all my existing MP3s come out of the speakers (line out) and headphone jack just fine.
Anyone know if there are potential conflicts between the system and audio editing software? Or perhaps it's the sound chip on the motherboard?
Related question: Can you add a sound card to a Mac Pro? I know the chip is soldered to the motherboard, but wondering if I can bypass that by adding a sound card?
Thanks for any help.

I haven't spent much time with Garage Band and I haven't used Cubase since OS9..
But there may be settings right in the DAW software that sets the default ins/outs as opposed to having your system settings control where the audio goes..
Another thing to take a look at is Audio MIDI Setup in the Utilities folder. It displays the system sound settings in a bit more detail...
Currently, there might be 1 or 2 PCI-express "sound cards" out there, but your best bet would be to look for a USB or, preferably, a Firewire audio interface. There are many of these out there with a large range in pricing..
If you are getting serious about recording, you may want to look at some of the small format mixers which include a USB or FW output. The advantage of these small mixers is that they are like swiss army knives for audio.. they allow you to route and mix audio in all kinds of ways that you would never imagine until you actually need it.. Some include digital effects, usually some EQ on every channel, from 2-16 mic pres, etc
Another route, again if you are getting more serious, is to get a ProTools LE or M-Powered setup. This way you are getting "Industry Standard" recording software along with a selection of different audio interfaces to choose from depending on your needs..
Apple Logic is also Pro-Level Software for a great price, especially at the current pricing.. You still need an interface, though, to get the most out of it.
Browse around the computer recording section at www.sweetwater.com to get a good idea of what's involved..

Sample rate off the audio input and out devices do not match - what to do?

Similar Messages

Maybe you are looking for