Samsung brightside not connecting to computer properly.

I am trying to get my samsung brightside to connect to my computer for data transfer and can't seem to get it to connect. I plug it in and it goes to charging mode, this is telling me that 1 my cable is good and 2 my ports on my computer are good (I also plug it into another computer and it does the same thing). I checked the USB Mode in settings >USB Mode and made sure it says USB Mass Storage still nothing. I also made sure that im on the "home" screen when im plugged in. the last thing I should mention is that this has worked before.

I must not be clear enough in my description as to what is going on. Or you guys don't understand windows all that much. when you plug in any memory device you are able to see the device in "My computer"
as shown below (shown with one of my flash drives)
now when I plug my phone in having it on USB Mass storage as advised here (your site's instructions where down when I posted this) the phone is not showing up in the screen above as shown below. my phone is only charging when plugged into my computer. and I have plugged it into different computers with the same results.
How can I fix this so I can get at the micro SD card that I do have inserted and to be able to see the Phone again.

Similar Messages

  • Ipad not connect with computer. error number (0xE8000084), ipad not connect with computer error number (0xE8000084)

    ipad not connected to computer. erreo number (0xE8000084)

    Hello Mohamed Abdo,
    It sounds like you are unable to connect your iPad to the computer because you get this error code when you try. I would use the troubleshooting for these types of errors from the following article:
    iOS: Unknown error containing '0xE' when connecting to a Windows PC
    http://support.apple.com/kb/TS3221
    Start with these steps, and there are additional steps in the article if you need them:
    1. Restart your computer.
    2. Install the latest version of iTunes.
    3. Verify that your computer meets the minimum system requirements. iOS devices require the following minimum version of Windows:
    Windows XP Service Pack 3
    Windows Vista
    Windows 7
    Windows 8
    4. Download and install any available software updates from Microsoft.
    5. Connect the device directly to your computer; not to an external USB hub. Find out if your computer has USB 2.0 ports.
    6. Check that the Dock Connector or Lightning Connector on both the device and cable are clean of any lint or other debris. If possible, connect your device using a different Apple 30-pin to USB cable or Apple Lightning Connector to USB cable.
    7. Disconnect other USB peripherals from your computer, with the exception of your keyboard and mouse. After disconnecting these peripherals, restart your computer, connect your device, and open iTunes.
    8. Connect your device to a different USB port on your computer.
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • OfficeJet 6500 709e says it's not connected to computer

    When I press the "wrench" button onmy printer, then press something to get help on anything, the LCD dispay shows "Not connected to computer"
    Yet, I can print fine using my computer.
    I have a wired setup.
    How can I get the printer to think it's connected to my computer?

    What is the exact wording of the error message?
    What are you trying to do?
    The USB connection provides not internet connectivity. The iPod can only connect to the internet via wifi

  • HT201412 Hi , my Ipod touch4 not turning on even not connecting to computer... How can i fix this problem !!!! plz

    Hi , my Ipod touch4 not turning on even not connecting to computer... How can i fix this problem !!!! plz

    lbryan1987 wrote:
    I dont want the button problem solved i need to know how to restore the phone without using that button or going into settings
    You don't in the condition it's in. You will either have to get the phone replaced by Apple or pay a 3rd party to repair it.
    there seriously should be more than two ways to solve this other wise apple is useless and we will never buy another apple product.
    Seriously? It's physically broken!

  • Unable to start T-sql Debugging . could not connect to computer'.'.the workastaion service hase not been started

    hello
    when i excute code in sql server 2008, this error appear:
    unable to start T-sql Debugging . could not connect to computer'.'.the workastaion service hase not been started.
    what do i do?
    thanks

    hello
    when i excute code in sql server 2008, this error appear:
    unable to start T-sql Debugging . could not connect to computer'.'.the workastaion service hase not been started.
    what do i do?
    thanks
    Hello,
    This forum is to discuss and ask questions about the Debugging tools of
    Visual Studio, Visual Studio Profiler tools, and Visual Studio Ultimate IntelliTrace, it seems like that your issue is out of the support range which is regarding
    Using the Transact-SQL Debugger, if that is the case, I would recommend you post this issue in the following forum like this thread
    Unable to start T-SQL debuging.
    SQL Server>Transact-SQL
    Regards,
    Carl
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • Ipod touch screen shows connecting to itunes when not connected to computer and will not go to start screen  also will not connect to itunes get message that passcode needs to be entered but cannot get to that screen on ipod

    ipod touch shows connecting to itunes on screen even when not connected to computer.  cannot get to start screen to enter my passcode

    Place the iPod in recovery mode to bypass the passcode (and essentially erase your iPod)  and then restore via iTunes on your computer.

  • My IPOD is not connected but computer says it is

    I had a IPOD nano 2GB but I decided to upgrade to an IPOD 4GB so I can play videos. So far I am not impressed with it. On my old nano it was very organized. I had 2 playlists and and audioobok category. On my new IPOD I have a million categories and I can't seem to get it organized. I have music I don't want and can't seem to delete( songs aren't highlighted) I can't add a new playlist. So far I have music everywhere. I can't seem to add either I can't put the video where I want it. ETC ETC ETC. What is the problem? My old Nano seem to be so easy to use. Just plug it in the computer and voila. I tunes says it is pluggged in and updated, but nothing seems to working properly.
    IPOD Nano 4GB Windows XP Pro
    My new IPOD acts like it is not connected. That is why none of my songs are highlighted and I can't make a new playlist. Right now I have my new IPOD hooked on the computer to Itunes but it is not playing through itunes like the old one. I have tried to download the newest version of Itunes but it says I have the latest. The computer(Itunes) says it is connected and insync but for some reason not taking it. Do I need to take this back to the apple store?

    Do the iPod Disk Diagnotic in this excellent post by tt2.
    If the report is good
    Try using the USB 2.0 port at the back of the PC
    Disconnect all other USB devices
    Dont use any other Apps while you are syncing or Restoring.the iPod.
    Disconnect from Internet and stop the Antivirus or other monitoring software.
    Have anice day!

  • Officejet 4630 will not connect to computer to scan.

    When I first got the product it scanned a few times but now will not connect to my computer to scan even after re-downloading drivers and entering a printer claim code.

    I would recommend using the HP Print and Scan Doctor to help diagnose and resolve your connection issue.
    Say Thanks by clicking the Kudos Star. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
    I am an HP employee.

  • Ipod does not connect to computer or show up in itunes

    I plug my ipod into the computer and it does not show up in itunes. It worked when I first bought it 3 months ago and suddenly will not connect...
    I have tried other computers as well as rebooting and then connecting but still nothing...
    It is incredibly frustrating. Any ideas?

    Same Problem. I have a 4 year old 40G click wheel. all was fine until today. now when i connect to my PC i do not hear the audible tone and nothing happens except my iPod turns on but i do not get the "Do not Disconnet" message and my iPod does NOT show up in iTunes. also, it causes my computer to lock up and i have to turn off the computer and reboot just to use my computer. tried reset; tried the disk mode. still not working. it did this yesterday once and i reset my iPod and all was fine. today, that doesn't work. any ideas????
    HP nc6320   Windows XP  
    HP nc6320   Windows XP  

  • My iPad is Disabled and I cannot input my passcode.  how do i do that?  I have tried to connect to iTunes and it will not connect via computer connection as I cannot activate my iPad with the pass code.  what do i do?

    My iPad is disabled and I can not input my passcode.  what do i need to do?  I tried to connect to iTunes, but it will not allow me to connect via compute USB as I cannot input my passcode for the iPad. 

    You may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808 - you should then be able to reset the iPad and restore/re-sync your content to it

  • IBook not connecting: Other computer has no problem

    We connect to the net via an ethernet cable using PPOE. We are not usually on at the same time, so we just unplug the cable from whichever computer is using it and plug it in the other. Never had any problems swapping the cable between computers when one of us wanted to use the net.
    Now my wife's iBook isn't connecting. My PowerBook has no problems, but when her iBook tries to connect, it says that authentication failed. When I ran diagnostics, it said that the cable was not plugged in or that it was not connected to a network.
    I've tried: repair permissions, turning it off and back on again, typing in ID/password manually, using the assistant, deleting Quicktime and prefs (saw this on a post), unplugging iBook and taking out battery for half-hour (had to reset time and date).
    I can share my connection via airport, but her Safari is SLooooooow and when I tried to do a software update on her iBook using this shared connection, it would not connect (lost network connection (-1005.) When I hit "Network Diagnostics", it all came back green: no problems.
    Any help would be greatly appreciated.
    Thanks.

    ok, the quicktime compatibility update (took several tries and about two hours to download) seems to have done the trick.
    fun fun fun.

  • My Zen Sleek Photo will not connect to compute

    I am extremely disappointed ! Despite being told yesterday that I need Microsoft Service Pack 2 installed on my computer before my USB would detect the player, I have successfully downloaded MS SP 2 and guess what ? It still says "your player is not connected" !!! Grrrr !
    220 down the spout !?Help ! Please !!?

    To: suzanneb
    I wonder if DM Guru's?solution might work for you.
    Good Luck!
    aismail
    I wonder if DM Guru's?solution might work for you.
    Good Luck!
    Message Edited by roger-conejo on 02-9-20060:3 AM

  • HP Photosmart 7520 not connected to computer when trying to scan

    Hi!!
    I have an IMac.  I can print from my computer, and my computer recognizes my printer (HP Photosmart 7520), however, my printer will not connect to my iMac...Help!  ;-)
    When I am trying to scan, the exact warning is:  "No Connection:  No computer is connected.  See printer Help and documentation to troubleshoot the connection."
    When I go to printer Help and doc, it says to install the HP software on my computer.
    I already went through most of the troubleshooting steps I could find (on my computer and online) - they only dealt with my computer not recognizing my printer...not vice versa...
    The little bluetooth light is lit and going strong...
    Thanks in advance!!!
    Katie

    Hi @ktsue,
    Welcome to the HP Forums!
    I understand that you cannot scan with your HP Photosmart 7520 on your Mac. I am happy to help you with this scanning issue!
    For further assistance, I will need some additional information:
    The version of Mac Operating System that you are using. To find the exact version, visit this link. Whatsmyos.
    If the printer is connected, Wireless, or USB.
    If the printer is able to make copies. Copy Text or Mixed Documents.
    If the power cable is plugged into a surge protector, or directly to the wall outlet. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector. This applies to Inkjet printers as well. 
    In the meantime, please see this scanning guide, A 'No Computer Detected' or 'Connection Error' Message Displays for HP Photosmart 7520 e-All-in-One .... (Even though the guide title may not match your issue, I believe the solutions will help).
    Thank you for posting!
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • Nokia 2600 classic will not connect to computer

    hi i have installed and uninstalled Nokia pc suite several times , tried on both windows 7 and xp pro, and tried the registry cleaner for clearing nokia files and i cannot get this phone to connect to my computer. It will not connect when asked to at start up screen for nokia pc suite.  Can anyone help?

    could you try like this?
    1. open PC suite, select "setting"
    2. then select "manage connection"
    3. select bluetooth ( others should not be used for 2600c)
    4. then doule click the "bluetooth" icon and start to search your 2600c (ensure your 2600c' bluetooth is active)
    good luck!
    if this answer is helpful for solving your issue, pls press the white star, thanks!

  • Alarm on Samsung Brightside not working

    My Samsung Brightside phone alarm does not work when I set it to go off  in the  mornings it will not work, but when I set it  later in the day it will work. Has anyone else had this problem with their Samsung Brightside?

    CallieGP: Your Samsung Brightside could very well be one of those "batch" phones that were defective when sold. It has nothing to do with the internet being blocked, either. The phone may be defective and Verizon refuses to issue new phones because they aren't any "new" ones that have been fixed or manufactured to actually work as marketed, as sold for profit. Verizon does not care about the customers who bought these alleged defective phones - they are too busy marketing and selling the higher priced smart phones.
    Check your calendar function. Do a test calendar event - set a test even for 3 different days and see if the calendar function works. If it epic fails, then you most likely have a defective phone from the original batch. Verizon won't refund your money and it will try to give you a "certified like new" Samsung Brightside which is a used phone that is most likely from the original defective batches that were mass produced, marketed and sold to the unsuspecting and "sucker" public. Let me know about your calendar, please. The more people that state they have a problem(s) with the Samsung Brightside, the more defense i have to bring a lawsuit against Verizon. But it will counter with "oh, it's the manufacturer's problem" even though Verizon continues to market and sell these phones for a profit. keep me posted!

Maybe you are looking for