Samsung NP305V5A: Screen does not come back after resume
The issue: screen does not turn ON when resuming from suspend-to-ram. PC fans start working. I can even "gently" reboot the notebook, by pressing <Ctrl>+<Alt>+<F1>, then <Ctrl>+<Alt>+<Del>. But the screen does not work..
Note: resume worked with the Catalyst driver (but this blob has many other glitches...)
$ lspci | grep VGA
00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] BeaverCreek [Radeon HD 6520G]
02:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Seymour [Radeon HD 6400M/7400M Series]
Video driver: radeon
Kernel parameters: root=/dev/sda2 rw radeon.dpm=1
(note: radeon.dpm=1 helps a lot; before kernel v3.11 I could not use radeon at all)
/etc/X11/xorg.conf.d/20-radeon.conf
Section "Device"
Identifier "Radeon"
Driver "radeon"
Option "ZaphodHeads" "VGA-0"
Option "ColorTiling2D" "false"
EndSection
not sure if the following is usable, but still:
$ lsmod | grep video
uvcvideo 72900 0
videobuf2_vmalloc 3280 1 uvcvideo
videobuf2_memops 2343 1 videobuf2_vmalloc
videobuf2_core 28027 1 uvcvideo
videodev 111140 2 uvcvideo,videobuf2_core
media 11751 2 uvcvideo,videodev
i2c_core 24164 6 drm,i2c_piix4,drm_kms_helper,i2c_algo_bit,radeon,videodev
video 11196 1 samsung_laptop
usbcore 179880 6 uvcvideo,ohci_hcd,ohci_pci,ehci_hcd,ehci_pci,usbhid
Hi moose53,
Just tested it with a Logitech keyboard and you are right, what you are describing is not expected behavior. I see you do not have any add ons, however does this also reproduce in Safe Mode? [[Troubleshoot Firefox issues using Safe Mode]]
If yes, try a new profile [[Use the Profile Manager to create and remove Firefox profiles]]
Similar Messages
-
Full Screen Does Not Come Back After Minimizing Firefox to the Taskbar.
Full Screen Does Not Come Back After Minimizing Firefox to the Taskbar.
I work in full screen almost exclusively ... the toolbar and the URL are still displayed while in full screen.
Before this version (30.0), when I minimized Firefox to the taskbar so that I could go to the desktop or to Windows Explorer, when I finished what I was doing and re-selected Firefox it would go back to full screen. Now, it does not go back to full screen. I can still see the taskbar. I have to press [f11] two more times to get back to full screen.
I have tried with and without addons enabled. Same behavior. I have reset Firefox ... same behavior.
I'm using Firefox 30.0 and Windows 7 (64 bit).
Thanks.Hi moose53,
Just tested it with a Logitech keyboard and you are right, what you are describing is not expected behavior. I see you do not have any add ons, however does this also reproduce in Safe Mode? [[Troubleshoot Firefox issues using Safe Mode]]
If yes, try a new profile [[Use the Profile Manager to create and remove Firefox profiles]] -
my ipad screen is black and will not reset and does not come back after restoring, the info is still on internal because i can see it on itunes in the apps catagory it's the display is not working, can see backlight but black...does anyone know how to fix, other than take it to apple.
thanks!The wish list only works on apps you have to pay for. To get it tap the icon of the app you want to save. After it opens at the upper right corner is a box with a arrow. Tap that then tap add to wish list list in the box that opens.
-
MBP does not come back after hybernation
Hello everyone,
I am enjoying my MBP except for one problem. It does not come back after it hybernates sometimes.
I hit a key, hear the superdrive do it's "thing" and then after much waiting (approximately over 10 minutes) no picture or video on the screen!
I can tell that it's still powered on because it's plugged in and when I hit the Caps Lock key it lights on and off.
The only way that I can get it out of this state is to hold down the power button, unplug the power cord, take the battery out, hold in the power button for 4 seconds, reinsert the battery and power back on.
I have to then cycle the power back off because the first time it does not come back but I just get the blank white boot screen and no 'apple'.
When I turn it back on the second time, it boots up.
Anyone else have a problem with this?
Thanks for listening!
MarkHello Gweedo!
Yeah I have the same issue and am up to date. Apparently this is a pretty huge problem with the Macbook Pro since the last Graphics update after updating to 10.5.2.
http://discussions.apple.com/thread.jspa?threadID=1394449
I have been perusing through that topic and hopefully they will come up with a fix for this.
The only work-a-round that I have found (but haven't tested extensively yet) is to disconnect to the wireless, turn off blue tooth, disconnect my external monitor and then go into sleep mode. Then it always comes back. But if I leave it connected to the wireless, bluetooth, and external monitor - it's a crap shoot as to weather or not it will come back up.
This is pretty frustrating because half of using a laptop is being able to hybernate and sleep properly.
I even have the 'smartsleep' installed.
Thanks for commenting everybody!
Mark -
My brand new iphone 4gs from Sprints, is turning off whenever it wants and does not come back after 2 or 3 hours???
Return it for a warranty replacement.
-
Laptop screen does not turn on after resume from suspend/hibernate
I use systemctl suspend/hibernate to resume, but the screen does not turn on from resume. everything else still functions just fine, meaning i can type in reboot and reboot, but a "turned off" black screen.
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h Processor Root Complex
00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] BeaverCreek [Radeon HD 6520G]
00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] BeaverCreek HDMI Audio [Radeon HD 6500D and 6400G-6600G series]
00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 12h Processor Root Port
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode]
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11)
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11)
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 13)
00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01)
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD] FCH PCI Bridge (rev 40)
00:15.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 0)
00:15.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 1)
00:15.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 2)
00:16.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11)
00:16.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11)
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 0 (rev 43)
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 3
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 4
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 6
00:18.6 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 5
00:18.7 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 12h/14h Processor Function 7
04:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.19.0-1-ARCH (builduser@tobias) (gcc version 4.9.2 20150204 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Feb 9 07:08:20 CET 2015
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=70f3d39a-cd3c-4127-84d2-9af3430201ab rw quiet rootfstype=xfs i8042.nomux=1 i8042.reset
[ 0.000000] tseg: 009ff00000
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ebff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009ec00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009f8f4fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009f8f5000-0x000000009f939fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f93a000-0x000000009f951fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000009f952000-0x000000009f954fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f955000-0x000000009f955fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009f956000-0x000000009f96cfff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009f96d000-0x000000009f974fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f975000-0x000000009f9a4fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009f9a5000-0x000000009f9a5fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f9a6000-0x000000009f9b5fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009f9b6000-0x000000009f9c3fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f9c4000-0x000000009f9c5fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009f9c6000-0x000000009f9ccfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009f9cd000-0x000000009fa02fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009fa03000-0x000000009fc05fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009fc06000-0x000000009fd78fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009fd79000-0x000000009fef5fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009fef6000-0x000000009fefffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed61000-0x00000000fed70fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100001000-0x000000023effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: TOSHIBA Satellite L775D/TKBSS, BIOS 1.40 07/22/2011
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x23f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF write-through
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF00000000 write-back
[ 0.000000] 1 base 009FF00000 mask FFFFF00000 uncachable
[ 0.000000] 2 base 00A0000000 mask FFE0000000 uncachable
[ 0.000000] 3 base 00C0000000 mask FFC0000000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000023f000000 aka 9200M
[ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC
[ 0.000000] e820: update [mem 0x9ff00000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0x9ff00 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fcf30-0x000fcf3f] mapped at [ffff8800000fcf30]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b32000, 0x01b32fff] PGTABLE
[ 0.000000] BRK [0x01b33000, 0x01b33fff] PGTABLE
[ 0.000000] BRK [0x01b34000, 0x01b34fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x23ee00000-0x23effffff]
[ 0.000000] [mem 0x23ee00000-0x23effffff] page 2M
[ 0.000000] BRK [0x01b35000, 0x01b35fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x220000000-0x23edfffff]
[ 0.000000] [mem 0x220000000-0x23edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x200000000-0x21fffffff]
[ 0.000000] [mem 0x200000000-0x21fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x9f8f4fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0x9f7fffff] page 2M
[ 0.000000] [mem 0x9f800000-0x9f8f4fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x9f955000-0x9f955fff]
[ 0.000000] [mem 0x9f955000-0x9f955fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x9f9a6000-0x9f9b5fff]
[ 0.000000] [mem 0x9f9a6000-0x9f9b5fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x9fc06000-0x9fd78fff]
[ 0.000000] [mem 0x9fc06000-0x9fd78fff] page 4k
[ 0.000000] BRK [0x01b36000, 0x01b36fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x9fef6000-0x9fefffff]
[ 0.000000] [mem 0x9fef6000-0x9fefffff] page 4k
[ 0.000000] BRK [0x01b37000, 0x01b37fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x100001000-0x1ffffffff]
[ 0.000000] [mem 0x100001000-0x1001fffff] page 4k
[ 0.000000] [mem 0x100200000-0x13fffffff] page 2M
[ 0.000000] [mem 0x140000000-0x1ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x37652000-0x37b20fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0450 000024 (v02 TOSASU)
[ 0.000000] ACPI: XSDT 0x000000009F93A070 000064 (v01 TOSASU TOSASU00 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x000000009F94E438 0000F4 (v04 TOSASU TOSASU00 01072009 AMI 00010013)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20141107/tbfadt-649)
[ 0.000000] ACPI: DSDT 0x000000009F93A168 0142CF (v02 TOSASU TOSASU00 00000140 INTL 20051117)
[ 0.000000] ACPI: FACS 0x000000009F9C6F80 000040
[ 0.000000] ACPI: APIC 0x000000009F94E530 000072 (v03 TOSASU TOSASU00 01072009 AMI 00010013)
[ 0.000000] ACPI: ECDT 0x000000009F94E5A8 0000C1 (v01 TOSASU TOSASU00 01072009 AMI. 00000004)
[ 0.000000] ACPI: SLIC 0x000000009F94E670 000176 (v01 TOSASU TOSASU00 01072009 MSFT 00000001)
[ 0.000000] ACPI: MCFG 0x000000009F94E7E8 00003C (v01 A M I GMCH945. 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x000000009F94E828 000038 (v01 TOSASU TOSASU00 01072009 AMI 00000004)
[ 0.000000] ACPI: SSDT 0x000000009F94E860 000E34 (v01 AMD POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 0x000000009F94F698 00193D (v02 AMD ALIB 00000001 MSFT 04000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000023effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x23eff8000-0x23effbfff]
[ 0.000000] [ffffea0000000000-ffffea0008ffffff] PMD -> [ffff880236e00000-ffff88023e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x23effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009dfff]
[ 0.000000] node 0: [mem 0x00100000-0x9f8f4fff]
[ 0.000000] node 0: [mem 0x9f955000-0x9f955fff]
[ 0.000000] node 0: [mem 0x9f9a6000-0x9f9b5fff]
[ 0.000000] node 0: [mem 0x9fc06000-0x9fd78fff]
[ 0.000000] node 0: [mem 0x9fef6000-0x9fefffff]
[ 0.000000] node 0: [mem 0x100001000-0x23effffff]
[ 0.000000] Initmem setup node 0 [mem 0x00001000-0x23effffff]
[ 0.000000] On node 0 totalpages: 1960479
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3997 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 10155 pages used for memmap
[ 0.000000] DMA32 zone: 649859 pages, LIFO batch:31
[ 0.000000] Normal zone: 20416 pages used for memmap
[ 0.000000] Normal zone: 1306623 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f8f5000-0x9f939fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f93a000-0x9f951fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f952000-0x9f954fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f956000-0x9f96cfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f96d000-0x9f974fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f975000-0x9f9a4fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f9a5000-0x9f9a5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f9b6000-0x9f9c3fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f9c4000-0x9f9c5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f9c6000-0x9f9ccfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9f9cd000-0x9fa02fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9fa03000-0x9fc05fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9fd79000-0x9fef5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9ff00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfec0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed60fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed61000-0xfed70fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed71000-0xfed7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x100000000-0x100000fff]
[ 0.000000] e820: [mem 0x9ff00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 31 pages/cpu @ffff88023ec00000 s86336 r8192 d32448 u524288
[ 0.000000] pcpu-alloc: s86336 r8192 d32448 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1929823
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=70f3d39a-cd3c-4127-84d2-9af3430201ab rw quiet rootfstype=xfs i8042.nomux=1 i8042.reset
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 7635708K/7841916K available (5531K kernel code, 917K rwdata, 1744K rodata, 1164K init, 1156K bss, 206208K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS:8448 nr_irqs:456 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 1397.380 MHz processor
[ 0.000043] Calibrating delay loop (skipped), value calculated using timer frequency.. 2795.20 BogoMIPS (lpj=4657933)
[ 0.000046] pid_max: default: 32768 minimum: 301
[ 0.000053] ACPI: Core revision 20141107
[ 0.000055] TOSHIBA Satellite detected - force copy of DSDT to local memory
[ 0.000123] ACPI: Forced DSDT copy: length 0x142CF copied locally, original unmapped
[ 0.015021] ACPI: All ACPI Tables successfully acquired
[ 0.016280] Security Framework initialized
[ 0.016286] Yama: becoming mindful.
[ 0.016907] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.019182] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.020189] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.020201] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.020472] Initializing cgroup subsys memory
[ 0.020479] Initializing cgroup subsys devices
[ 0.020482] Initializing cgroup subsys freezer
[ 0.020484] Initializing cgroup subsys net_cls
[ 0.020487] Initializing cgroup subsys blkio
[ 0.020510] CPU: Physical Processor ID: 0
[ 0.020511] CPU: Processor Core ID: 0
[ 0.020513] mce: CPU supports 6 MCE banks
[ 0.020522] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
Last level dTLB entries: 4KB 1024, 2MB 128, 4MB 64, 1GB 0
[ 0.020644] Freeing SMP alternatives memory: 20K (ffffffff81a0a000 - ffffffff81a0f000)
[ 0.021880] ftrace: allocating 21166 entries in 83 pages
[ 0.035456] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.068473] smpboot: CPU0: AMD A6-3400M APU with Radeon(tm) HD Graphics (fam: 12, model: 01, stepping: 00)
[ 0.174081] Performance Events: AMD PMU driver.
[ 0.174086] ... version: 0
[ 0.174087] ... bit width: 48
[ 0.174088] ... generic registers: 4
[ 0.174089] ... value mask: 0000ffffffffffff
[ 0.174090] ... max period: 00007fffffffffff
[ 0.174091] ... fixed-purpose events: 0
[ 0.174092] ... event mask: 000000000000000f
[ 0.191034] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.197738] x86: Booting SMP configuration:
[ 0.197744] .... node #0, CPUs: #1 #2 #3
[ 0.250891] x86: Booted up 1 node, 4 CPUs
[ 0.250896] smpboot: Total of 4 processors activated (11183.83 BogoMIPS)
[ 0.252264] devtmpfs: initialized
[ 0.257696] PM: Registering ACPI NVS region [mem 0x9f8f5000-0x9f939fff] (282624 bytes)
[ 0.257715] PM: Registering ACPI NVS region [mem 0x9f952000-0x9f954fff] (12288 bytes)
[ 0.257718] PM: Registering ACPI NVS region [mem 0x9f96d000-0x9f974fff] (32768 bytes)
[ 0.257721] PM: Registering ACPI NVS region [mem 0x9f9a5000-0x9f9a5fff] (4096 bytes)
[ 0.257724] PM: Registering ACPI NVS region [mem 0x9f9b6000-0x9f9c3fff] (57344 bytes)
[ 0.257727] PM: Registering ACPI NVS region [mem 0x9f9c6000-0x9f9ccfff] (28672 bytes)
[ 0.257729] PM: Registering ACPI NVS region [mem 0x9fa03000-0x9fc05fff] (2109440 bytes)
[ 0.258125] pinctrl core: initialized pinctrl subsystem
[ 0.258173] RTC time: 18:50:52, date: 02/22/15
[ 0.258343] NET: Registered protocol family 16
[ 0.270952] cpuidle: using governor ladder
[ 0.284279] cpuidle: using governor menu
[ 0.284490] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.284493] ACPI: bus type PCI registered
[ 0.284495] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.284605] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.284608] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.285035] PCI: Using configuration type 1 for base access
[ 0.299021] ACPI: Added _OSI(Module Device)
[ 0.299025] ACPI: Added _OSI(Processor Device)
[ 0.299027] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.299029] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.300870] ACPI : EC: EC description table is found, configuring boot EC
[ 0.302900] ACPI: Executed 2 blocks of module-level executable AML code
[ 0.831121] ACPI: Interpreter enabled
[ 0.831132] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20141107/hwxface-580)
[ 0.831140] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20141107/hwxface-580)
[ 0.831167] ACPI: (supports S0 S3 S4 S5)
[ 0.831169] ACPI: Using IOAPIC for interrupt routing
[ 0.831382] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.842727] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.842738] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.843157] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.843782] PCI host bridge to bus 0000:00
[ 0.843788] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.843792] pci_bus 0000:00: root bus resource [io 0x0000-0x03af]
[ 0.843796] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7]
[ 0.843800] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df]
[ 0.843803] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.843806] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.843810] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[ 0.843813] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
[ 0.843825] pci 0000:00:00.0: [1022:1705] type 00 class 0x060000
[ 0.843978] pci 0000:00:01.0: [1002:9647] type 00 class 0x030000
[ 0.843993] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff pref]
[ 0.844002] pci 0000:00:01.0: reg 0x14: [io 0xf000-0xf0ff]
[ 0.844011] pci 0000:00:01.0: reg 0x18: [mem 0xfeb00000-0xfeb3ffff]
[ 0.844070] pci 0000:00:01.0: supports D1 D2
[ 0.844185] pci 0000:00:01.1: [1002:1714] type 00 class 0x040300
[ 0.844197] pci 0000:00:01.1: reg 0x10: [mem 0xfeb44000-0xfeb47fff]
[ 0.844272] pci 0000:00:01.1: supports D1 D2
[ 0.844388] pci 0000:00:02.0: [1022:1707] type 01 class 0x060400
[ 0.844483] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.844641] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[ 0.844665] pci 0000:00:11.0: reg 0x10: [io 0xf190-0xf197]
[ 0.844678] pci 0000:00:11.0: reg 0x14: [io 0xf180-0xf183]
[ 0.844690] pci 0000:00:11.0: reg 0x18: [io 0xf170-0xf177]
[ 0.844703] pci 0000:00:11.0: reg 0x1c: [io 0xf160-0xf163]
[ 0.844715] pci 0000:00:11.0: reg 0x20: [io 0xf150-0xf15f]
[ 0.844728] pci 0000:00:11.0: reg 0x24: [mem 0xfeb4e000-0xfeb4e7ff]
[ 0.844896] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[ 0.844914] pci 0000:00:12.0: reg 0x10: [mem 0xfeb4d000-0xfeb4dfff]
[ 0.845044] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 0.845114] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[ 0.845138] pci 0000:00:12.2: reg 0x10: [mem 0xfeb4c000-0xfeb4c0ff]
[ 0.845242] pci 0000:00:12.2: supports D1 D2
[ 0.845245] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.845313] pci 0000:00:12.2: System wakeup disabled by ACPI
[ 0.845383] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[ 0.845400] pci 0000:00:13.0: reg 0x10: [mem 0xfeb4b000-0xfeb4bfff]
[ 0.845529] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.845599] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[ 0.845623] pci 0000:00:13.2: reg 0x10: [mem 0xfeb4a000-0xfeb4a0ff]
[ 0.845727] pci 0000:00:13.2: supports D1 D2
[ 0.845730] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.845799] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.845867] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 0.846051] pci 0000:00:14.1: [1022:780c] type 00 class 0x01018a
[ 0.846069] pci 0000:00:14.1: reg 0x10: [io 0xf140-0xf147]
[ 0.846081] pci 0000:00:14.1: reg 0x14: [io 0xf130-0xf133]
[ 0.846094] pci 0000:00:14.1: reg 0x18: [io 0xf120-0xf127]
[ 0.846107] pci 0000:00:14.1: reg 0x1c: [io 0xf110-0xf113]
[ 0.846119] pci 0000:00:14.1: reg 0x20: [io 0xf100-0xf10f]
[ 0.846145] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.846148] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.846151] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.846154] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.846275] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 0.846303] pci 0000:00:14.2: reg 0x10: [mem 0xfeb40000-0xfeb43fff 64bit]
[ 0.846387] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.846454] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 0.846515] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 0.846704] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
[ 0.846806] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.846879] pci 0000:00:15.0: [1022:43a0] type 01 class 0x060400
[ 0.846982] pci 0000:00:15.0: supports D1 D2
[ 0.847053] pci 0000:00:15.0: System wakeup disabled by ACPI
[ 0.847122] pci 0000:00:15.1: [1022:43a1] type 01 class 0x060400
[ 0.847225] pci 0000:00:15.1: supports D1 D2
[ 0.847296] pci 0000:00:15.1: System wakeup disabled by ACPI
[ 0.847363] pci 0000:00:15.2: [1022:43a2] type 01 class 0x060400
[ 0.847466] pci 0000:00:15.2: supports D1 D2
[ 0.847537] pci 0000:00:15.2: System wakeup disabled by ACPI
[ 0.847610] pci 0000:00:16.0: [1022:7807] type 00 class 0x0c0310
[ 0.847628] pci 0000:00:16.0: reg 0x10: [mem 0xfeb49000-0xfeb49fff]
[ 0.847757] pci 0000:00:16.0: System wakeup disabled by ACPI
[ 0.847827] pci 0000:00:16.2: [1022:7808] type 00 class 0x0c0320
[ 0.847851] pci 0000:00:16.2: reg 0x10: [mem 0xfeb48000-0xfeb480ff]
[ 0.847956] pci 0000:00:16.2: supports D1 D2
[ 0.847959] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 0.848026] pci 0000:00:16.2: System wakeup disabled by ACPI
[ 0.848093] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000
[ 0.848228] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000
[ 0.848359] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000
[ 0.848490] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000
[ 0.848632] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000
[ 0.848762] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000
[ 0.848892] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000
[ 0.849021] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000
[ 0.849252] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.849360] pci 0000:00:14.4: PCI bridge to [bus 02] (subtractive decode)
[ 0.849372] pci 0000:00:14.4: bridge window [io 0x0000-0x03af] (subtractive decode)
[ 0.849376] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7] (subtractive decode)
[ 0.849379] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df] (subtractive decode)
[ 0.849383] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.849387] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.849390] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.849394] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xffffffff] (subtractive decode)
[ 0.849483] pci 0000:00:15.0: PCI bridge to [bus 03]
[ 0.849617] pci 0000:04:00.0: [10ec:8176] type 00 class 0x028000
[ 0.849646] pci 0000:04:00.0: reg 0x10: [io 0xe000-0xe0ff]
[ 0.849687] pci 0000:04:00.0: reg 0x18: [mem 0xfea00000-0xfea03fff 64bit]
[ 0.849834] pci 0000:04:00.0: supports D1 D2
[ 0.849837] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.849878] pci 0000:04:00.0: System wakeup disabled by ACPI
[ 0.854467] pci 0000:00:15.1: PCI bridge to [bus 04]
[ 0.854488] pci 0000:00:15.1: bridge window [io 0xe000-0xefff]
[ 0.854499] pci 0000:00:15.1: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.854661] pci 0000:05:00.0: [10ec:8136] type 00 class 0x020000
[ 0.854688] pci 0000:05:00.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.854722] pci 0000:05:00.0: reg 0x18: [mem 0xd0004000-0xd0004fff 64bit pref]
[ 0.854743] pci 0000:05:00.0: reg 0x20: [mem 0xd0000000-0xd0003fff 64bit pref]
[ 0.854860] pci 0000:05:00.0: supports D1 D2
[ 0.854863] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.854907] pci 0000:05:00.0: System wakeup disabled by ACPI
[ 0.861144] pci 0000:00:15.2: PCI bridge to [bus 05]
[ 0.861165] pci 0000:00:15.2: bridge window [io 0xd000-0xdfff]
[ 0.861180] pci 0000:00:15.2: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.861237] acpi PNP0A03:00: Disabling ASPM (FADT indicates it is unsupported)
[ 0.861791] ACPI: PCI Interrupt Link [LN24] (IRQs *24)
[ 0.861823] ACPI: PCI Interrupt Link [LN25] (IRQs *25)
[ 0.861855] ACPI: PCI Interrupt Link [LN26] (IRQs *26)
[ 0.861887] ACPI: PCI Interrupt Link [LN27] (IRQs *27)
[ 0.861918] ACPI: PCI Interrupt Link [LN28] (IRQs *28)
[ 0.861951] ACPI: PCI Interrupt Link [LN29] (IRQs *29)
[ 0.861981] ACPI: PCI Interrupt Link [LN30] (IRQs *30)
[ 0.862011] ACPI: PCI Interrupt Link [LN31] (IRQs *31)
[ 0.862041] ACPI: PCI Interrupt Link [LN32] (IRQs *32)
[ 0.862071] ACPI: PCI Interrupt Link [LN33] (IRQs *33)
[ 0.862101] ACPI: PCI Interrupt Link [LN34] (IRQs *34)
[ 0.862130] ACPI: PCI Interrupt Link [LN35] (IRQs *35)
[ 0.862160] ACPI: PCI Interrupt Link [LN36] (IRQs *36)
[ 0.862190] ACPI: PCI Interrupt Link [LN37] (IRQs *37)
[ 0.862219] ACPI: PCI Interrupt Link [LN38] (IRQs *38)
[ 0.862249] ACPI: PCI Interrupt Link [LN39] (IRQs *39)
[ 0.862279] ACPI: PCI Interrupt Link [LN40] (IRQs *40)
[ 0.862309] ACPI: PCI Interrupt Link [LN41] (IRQs *41)
[ 0.862338] ACPI: PCI Interrupt Link [LN42] (IRQs *42)
[ 0.862368] ACPI: PCI Interrupt Link [LN43] (IRQs *43)
[ 0.862398] ACPI: PCI Interrupt Link [LN44] (IRQs *44)
[ 0.862428] ACPI: PCI Interrupt Link [LN45] (IRQs *45)
[ 0.862457] ACPI: PCI Interrupt Link [LN46] (IRQs *46)
[ 0.862487] ACPI: PCI Interrupt Link [LN47] (IRQs *47)
[ 0.862517] ACPI: PCI Interrupt Link [LN48] (IRQs *48)
[ 0.862546] ACPI: PCI Interrupt Link [LN49] (IRQs *49)
[ 0.862576] ACPI: PCI Interrupt Link [LN50] (IRQs *50)
[ 0.862606] ACPI: PCI Interrupt Link [LN51] (IRQs *51)
[ 0.862635] ACPI: PCI Interrupt Link [LN52] (IRQs *52)
[ 0.862665] ACPI: PCI Interrupt Link [LN53] (IRQs *53)
[ 0.862695] ACPI: PCI Interrupt Link [LN54] (IRQs *54)
[ 0.862726] ACPI: PCI Interrupt Link [LN55] (IRQs *55)
[ 0.862781] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0
[ 0.862883] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0
[ 0.862986] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0
[ 0.863084] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0
[ 0.863164] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.863228] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.863292] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.863356] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.864141] ACPI : EC: GPE = 0xc, I/O: command/status = 0x66, data = 0x62
[ 0.864446] vgaarb: setting as boot device: PCI:0000:00:01.0
[ 0.864452] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.864464] vgaarb: loaded
[ 0.864466] vgaarb: bridge control possible 0000:00:01.0
[ 0.864788] PCI: Using ACPI for IRQ routing
[ 0.874741] PCI: pci_cache_line_size set to 64 bytes
[ 0.874840] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff]
[ 0.874844] e820: reserve RAM buffer [mem 0x9f8f5000-0x9fffffff]
[ 0.874848] e820: reserve RAM buffer [mem 0x9f956000-0x9fffffff]
[ 0.874851] e820: reserve RAM buffer [mem 0x9f9b6000-0x9fffffff]
[ 0.874854] e820: reserve RAM buffer [mem 0x9fd79000-0x9fffffff]
[ 0.874856] e820: reserve RAM buffer [mem 0x9ff00000-0x9fffffff]
[ 0.874859] e820: reserve RAM buffer [mem 0x23f000000-0x23fffffff]
[ 0.875079] NetLabel: Initializing
[ 0.875081] NetLabel: domain hash size = 128
[ 0.875083] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.875101] NetLabel: unlabeled traffic allowed by default
[ 0.875143] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.875149] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.877246] Switched to clocksource hpet
[ 0.884868] pnp: PnP ACPI init
[ 0.885072] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.885079] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.886017] system 00:01: [io 0x04d0-0x04d1] has been reserved
[ 0.886021] system 00:01: [io 0x040b] has been reserved
[ 0.886025] system 00:01: [io 0x04d6] has been reserved
[ 0.886029] system 00:01: [io 0x0c00-0x0c01] has been reserved
[ 0.886032] system 00:01: [io 0x0c14] has been reserved
[ 0.886036] system 00:01: [io 0x0c50-0x0c51] has been reserved
[ 0.886039] system 00:01: [io 0x0c52] has been reserved
[ 0.886042] system 00:01: [io 0x0c6c] has been reserved
[ 0.886046] system 00:01: [io 0x0c6f] has been reserved
[ 0.886049] system 00:01: [io 0x0cd0-0x0cd1] has been reserved
[ 0.886052] system 00:01: [io 0x0cd2-0x0cd3] has been reserved
[ 0.886056] system 00:01: [io 0x0cd4-0x0cd5] has been reserved
[ 0.886059] system 00:01: [io 0x0cd6-0x0cd7] has been reserved
[ 0.886063] system 00:01: [io 0x0cd8-0x0cdf] has been reserved
[ 0.886067] system 00:01: [io 0x0800-0x089f] could not be reserved
[ 0.886070] system 00:01: [io 0x0b20-0x0b3f] has been reserved
[ 0.886074] system 00:01: [io 0x0900-0x090f] has been reserved
[ 0.886082] system 00:01: [io 0x0910-0x091f] has been reserved
[ 0.886086] system 00:01: [io 0xfe00-0xfefe] has been reserved
[ 0.886091] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.886096] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.886100] system 00:01: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.886104] system 00:01: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.886107] system 00:01: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.886112] system 00:01: [mem 0xfed00000-0xfed00fff] could not be reserved
[ 0.886116] system 00:01: [mem 0xff000000-0xffffffff] has been reserved
[ 0.886120] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.886180] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.886279] system 00:03: [io 0x04d0-0x04d1] has been reserved
[ 0.886283] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.886353] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.886420] system 00:05: [io 0x0240-0x0259] has been reserved
[ 0.886424] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.886523] pnp 00:06: Plug and Play ACPI device, IDs TOS0220 SYN1d00 SYN0002 PNP0f13 (active)
[ 0.886596] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.886784] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.887277] pnp: PnP ACPI: found 9 devices
[ 0.895955] pci 0000:00:02.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 0.895964] pci 0000:00:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 0.895969] pci 0000:00:02.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 0.896008] pci 0000:00:02.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.896012] pci 0000:00:02.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.896016] pci 0000:00:02.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.896026] pci 0000:00:02.0: BAR 14: assigned [mem 0xd0100000-0xd02fffff]
[ 0.896039] pci 0000:00:02.0: BAR 15: assigned [mem 0xd0300000-0xd04fffff 64bit pref]
[ 0.896046] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.896051] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.896056] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
[ 0.896061] pci 0000:00:02.0: bridge window [mem 0xd0100000-0xd02fffff]
[ 0.896067] pci 0000:00:02.0: bridge window [mem 0xd0300000-0xd04fffff 64bit pref]
[ 0.896073] pci 0000:00:14.4: PCI bridge to [bus 02]
[ 0.896089] pci 0000:00:15.0: PCI bridge to [bus 03]
[ 0.896103] pci 0000:00:15.1: PCI bridge to [bus 04]
[ 0.896107] pci 0000:00:15.1: bridge window [io 0xe000-0xefff]
[ 0.896114] pci 0000:00:15.1: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.896124] pci 0000:00:15.2: PCI bridge to [bus 05]
[ 0.896129] pci 0000:00:15.2: bridge window [io 0xd000-0xdfff]
[ 0.896138] pci 0000:00:15.2: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.896147] pci_bus 0000:00: resource 4 [io 0x0000-0x03af]
[ 0.896151] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7]
[ 0.896154] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df]
[ 0.896157] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff]
[ 0.896160] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[ 0.896164] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
[ 0.896167] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff]
[ 0.896171] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 0.896174] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd02fffff]
[ 0.896178] pci_bus 0000:01: resource 2 [mem 0xd0300000-0xd04fffff 64bit pref]
[ 0.896182] pci_bus 0000:02: resource 4 [io 0x0000-0x03af]
[ 0.896185] pci_bus 0000:02: resource 5 [io 0x03e0-0x0cf7]
[ 0.896188] pci_bus 0000:02: resource 6 [io 0x03b0-0x03df]
[ 0.896191] pci_bus 0000:02: resource 7 [io 0x0d00-0xffff]
[ 0.896194] pci_bus 0000:02: resource 8 [mem 0x000a0000-0x000bffff]
[ 0.896198] pci_bus 0000:02: resource 9 [mem 0x000c0000-0x000dffff]
[ 0.896201] pci_bus 0000:02: resource 10 [mem 0xc0000000-0xffffffff]
[ 0.896205] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.896208] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.896212] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 0.896215] pci_bus 0000:05: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.896259] NET: Registered protocol family 2
[ 0.896597] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.896863] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.897301] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.897360] TCP: reno registered
[ 0.897379] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.897467] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.897618] NET: Registered protocol family 1
[ 0.897646] pci 0000:00:01.0: Video device with shadowed ROM
[ 1.838171] PCI: CLS 64 bytes, default 64
[ 1.838242] Unpacking initramfs...
[ 1.934095] Freeing initrd memory: 4924K (ffff880037652000 - ffff880037b21000)
[ 1.934107] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.934110] software IO TLB [mem 0x9b8f5000-0x9f8f5000] (64MB) mapped at [ffff88009b8f5000-ffff88009f8f4fff]
[ 1.934495] microcode: CPU0: patch_level=0x03000014
[ 1.934537] microcode: CPU1: patch_level=0x03000014
[ 1.934580] microcode: CPU2: patch_level=0x03000014
[ 1.934625] microcode: CPU3: patch_level=0x03000014
[ 1.934758] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 1.934766] LVT offset 0 assigned for vector 0x400
[ 1.934817] perf: AMD IBS detected (0x000000ff)
[ 1.934854] Scanning for low memory corruption every 60 seconds
[ 1.935293] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 1.935315] Initialise system trusted keyring
[ 1.935789] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.937285] zpool: loaded
[ 1.937288] zbud: loaded
[ 1.937658] VFS: Disk quotas dquot_6.5.2
[ 1.937709] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.937948] Key type big_key registered
[ 1.938436] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.938508] io scheduler noop registered
[ 1.938511] io scheduler deadline registered
[ 1.938546] io scheduler cfq registered (default)
[ 1.939375] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[ 1.939380] pcie_pme 0000:00:02.0:pcie01: service driver pcie_pme loaded
[ 1.939399] pcieport 0000:00:15.0: Signaling PME through PCIe PME interrupt
[ 1.939403] pcie_pme 0000:00:15.0:pcie01: service driver pcie_pme loaded
[ 1.939421] pcieport 0000:00:15.1: Signaling PME through PCIe PME interrupt
[ 1.939423] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 1.939428] pcie_pme 0000:00:15.1:pcie01: service driver pcie_pme loaded
[ 1.939447] pcieport 0000:00:15.2: Signaling PME through PCIe PME interrupt
[ 1.939449] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt
[ 1.939453] pcie_pme 0000:00:15.2:pcie01: service driver pcie_pme loaded
[ 1.939461] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.939494] pciehp 0000:00:02.0:pcie04: Slot #2 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
[ 1.939528] pciehp 0000:00:02.0:pcie04: service driver pciehp loaded
[ 1.939533] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.939550] vesafb: mode is 1152x864x32, linelength=4608, pages=0
[ 1.939552] vesafb: scrolling: redraw
[ 1.939554] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[ 1.939576] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90010e80000, using 3904k, total 3904k
[ 1.955978] Console: switching to colour frame buffer device 144x54
[ 1.972261] fb0: VESA VGA frame buffer device
[ 1.972328] GHES: HEST is not enabled!
[ 1.972535] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.973720] Linux agpgart interface v0.103
[ 1.973797] rtc_cmos 00:02: RTC can wake from S4
[ 1.973936] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.973964] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.973983] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.974434] TCP: cubic registered
[ 1.974593] NET: Registered protocol family 10
[ 1.975020] NET: Registered protocol family 17
[ 1.975476] Loading compiled-in X.509 certificates
[ 1.975502] registered taskstats version 1
[ 1.976231] Magic number: 3:326:848
[ 1.976341] rtc_cmos 00:02: setting system clock to 2015-02-22 18:50:54 UTC (1424631054)
[ 1.976444] PM: Hibernation image not present or could not be loaded.
[ 1.977023] Freeing unused kernel memory: 1164K (ffffffff818e7000 - ffffffff81a0a000)
[ 1.977027] Write protecting the kernel read-only data: 8192k
[ 1.977495] Freeing unused kernel memory: 600K (ffff88000156a000 - ffff880001600000)
[ 1.977718] Freeing unused kernel memory: 304K (ffff8800017b4000 - ffff880001800000)
[ 1.979659] random: systemd urandom read with 1 bits of entropy available
[ 1.980307] systemd[1]: systemd 219 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[ 1.980576] systemd[1]: Detected architecture 'x86-64'.
[ 1.980581] systemd[1]: Running in initial RAM disk.
[ 1.980590] systemd[1]: Running with unpopulated /etc.
[ 1.980603] systemd[1]: No hostname configured.
[ 1.980609] systemd[1]: Set hostname to <localhost>.
[ 1.980655] systemd[1]: Initializing machine ID from random generator.
[ 1.996373] systemd[1]: Populated /etc with preset unit settings.
[ 1.999327] systemd[1]: Unit type .busname is not supported on this system.
[ 2.003390] systemd[1]: Created slice -.slice.
[ 2.003412] systemd[1]: Starting -.slice.
[ 2.005054] systemd[1]: Listening on Journal Audit Socket.
[ 2.005188] systemd[1]: Created slice system.slice.
[ 2.005200] systemd[1]: Starting system.slice.
[ 2.005218] systemd[1]: Reached target Swap.
[ 2.005226] systemd[1]: Starting Swap.
[ 2.005288] systemd[1]: Listening on udev Control Socket.
[ 2.005296] systemd[1]: Starting udev Control Socket.
[ 2.005312] systemd[1]: Reached target Slices.
[ 2.005320] systemd[1]: Starting Slices.
[ 2.005335] systemd[1]: Reached target Local File Systems.
[ 2.005342] systemd[1]: Starting Local File Systems.
[ 2.005358] systemd[1]: Reached target Timers.
[ 2.005366] systemd[1]: Starting Timers.
[ 2.005398] systemd[1]: Listening on udev Kernel Socket.
[ 2.005409] systemd[1]: Starting udev Kernel Socket.
[ 2.005430] systemd[1]: Reached target Paths.
[ 2.005441] systemd[1]: Starting Paths.
[ 2.005497] systemd[1]: Listening on Journal Socket.
[ 2.005510] systemd[1]: Starting Journal Socket.
[ 2.006097] systemd[1]: Starting udev Coldplug all Devices...
[ 2.006689] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 2.006801] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 2.006811] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 2.006860] systemd[1]: Listening on Journal Socket (/dev/log).
[ 2.006870] systemd[1]: Starting Journal Socket (/dev/log).
[ 2.007428] systemd[1]: Starting Journal Service...
[ 2.007472] systemd[1]: Reached target Sockets.
[ 2.007494] systemd[1]: Starting Sockets.
[ 2.011399] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 2.012026] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 2.012842] systemd-journald[63]: Failed to set file attributes: Inappropriate ioctl for device
[ 2.016230] systemd[1]: Started Create Static Device Nodes in /dev.
[ 2.016999] systemd[1]: Starting udev Kernel Device Manager...
[ 2.021212] systemd[1]: Started udev Kernel Device Manager.
[ 2.024169] systemd[1]: Started udev Coldplug all Devices.
[ 2.029792] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.032026] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.032044] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.041719] SCSI subsystem initialized
[ 2.042505] ACPI: bus type USB registered
[ 2.042538] usbcore: registered new interface driver usbfs
[ 2.042552] usbcore: registered new interface driver hub
[ 2.042588] usbcore: registered new device driver usb
[ 2.044174] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.045154] systemd[1]: Started Journal Service.
[ 2.045633] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.045840] ohci-pci: OHCI PCI platform driver
[ 2.045993] QUIRK: Enable AMD PLL fix
[ 2.046022] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 2.046033] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1
[ 2.046079] ohci-pci 0000:00:12.0: irq 18, io mem 0xfeb4d000
[ 2.046697] ehci-pci: EHCI PCI platform driver
[ 2.047833] libata version 3.00 loaded.
[ 2.084196] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 2.102273] hub 1-0:1.0: USB hub found
[ 2.102287] hub 1-0:1.0: 5 ports detected
[ 2.102593] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 2.102600] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2
[ 2.102631] ohci-pci 0000:00:13.0: irq 18, io mem 0xfeb4b000
[ 2.159071] hub 2-0:1.0: USB hub found
[ 2.159085] hub 2-0:1.0: 5 ports detected
[ 2.160195] ohci-pci 0000:00:16.0: OHCI PCI host controller
[ 2.160202] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 3
[ 2.160235] ohci-pci 0000:00:16.0: irq 18, io mem 0xfeb49000
[ 2.215699] hub 3-0:1.0: USB hub found
[ 2.215713] hub 3-0:1.0: 4 ports detected
[ 2.271489] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 2.271502] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 4
[ 2.271509] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 2.271523] ehci-pci 0000:00:12.2: debug port 1
[ 2.271574] ehci-pci 0000:00:12.2: irq 17, io mem 0xfeb4c000
[ 2.281276] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 2.281694] hub 4-0:1.0: USB hub found
[ 2.281705] hub 4-0:1.0: 5 ports detected
[ 2.338086] hub 1-0:1.0: USB hub found
[ 2.338100] hub 1-0:1.0: 5 ports detected
[ 2.338571] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 2.338579] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 5
[ 2.338584] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 2.338596] ehci-pci 0000:00:13.2: debug port 1
[ 2.338634] ehci-pci 0000:00:13.2: irq 17, io mem 0xfeb4a000
[ 2.347963] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 2.348396] hub 5-0:1.0: USB hub found
[ 2.348414] hub 5-0:1.0: 5 ports detected
[ 2.404806] hub 2-0:1.0: USB hub found
[ 2.404820] hub 2-0:1.0: 5 ports detected
[ 2.461536] ehci-pci 0000:00:16.2: EHCI Host Controller
[ 2.461550] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 6
[ 2.461557] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 2.461571] ehci-pci 0000:00:16.2: debug port 1
[ 2.461611] ehci-pci 0000:00:16.2: irq 17, io mem 0xfeb48000
[ 2.471331] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 2.471768] hub 6-0:1.0: USB hub found
[ 2.471780] hub 6-0:1.0: 4 ports detected
[ 2.528139] hub 3-0:1.0: USB hub found
[ 2.528154] hub 3-0:1.0: 4 ports detected
[ 2.528415] ahci 0000:00:11.0: version 3.0
[ 2.528689] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 2.528693] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part sxs
[ 2.529180] scsi host0: ahci
[ 2.529664] scsi host1: ahci
[ 2.529777] ata1: SATA max UDMA/133 abar m2048@0xfeb4e000 port 0xfeb4e100 irq 28
[ 2.529781] ata2: SATA max UDMA/133 abar m2048@0xfeb4e000 port 0xfeb4e180 irq 28
[ 2.530551] scsi host2: pata_atiixp
[ 2.530815] scsi host3: pata_atiixp
[ 2.530912] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf100 irq 14
[ 2.530914] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf108 irq 15
[ 2.654798] usb 5-4: new high-speed USB device number 2 using ehci-pci
[ 2.934859] tsc: Refined TSC clocksource calibration: 1397.458 MHz
[ 3.014908] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.014947] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.016183] ata1.00: ATA-8: Hitachi HTS547550A9E384, JE3OA60B, max UDMA/133
[ 3.016190] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 3.016972] ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633F, TF01, max UDMA/100
[ 3.017307] ata1.00: configured for UDMA/133
[ 3.017807] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54755 A60B PQ: 0 ANSI: 5
[ 3.019278] ata2.00: configured for UDMA/100
[ 3.025787] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L633F TF01 PQ: 0 ANSI: 5
[ 3.044649] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 3.044654] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.044859] sd 0:0:0:0: [sda] Write Protect is off
[ 3.044865] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.044918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.061859] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.061874] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.062232] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.084075] sda: sda1 sda2 sda3
[ 3.085567] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.414041] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 3.528901] XFS (sda1): Mounting V4 Filesystem
[ 3.710527] XFS (sda1): Ending clean mount
[ 3.935255] Switched to clocksource tsc
[ 3.999076] systemd-journald[63]: Received SIGTERM from PID 1 (systemd).
[ 4.799287] random: nonblocking pool is initialized
[ 6.377516] systemd-journald[187]: Failed to set file attributes: Inappropriate ioctl for device
[ 7.417234] ACPI: acpi_idle registered with cpuidle
[ 7.464892] acpi-cpufreq: overriding BIOS provided _PSD data
[ 7.544509] wmi: Mapper loaded
[ 7.612504] ACPI: Video Device [VGA1] (multi-head: yes rom: no post: no)
[ 7.626522] acpi device:2b: registered as cooling_device4
[ 7.626631] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:01/input/input2
[ 7.700708] ACPI Warning: SystemIO range 0x0000000000000b00-0x0000000000000b07 conflicts with OpRegion 0x0000000000000b00-0x0000000000000b0f (\SMBX) (20141107/utaddress-258)
[ 7.700729] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.734642] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[ 7.737166] thermal LNXTHERM:00: registered as thermal_zone0
[ 7.737173] ACPI: Thermal Zone [THRM] (50 C)
[ 7.746486] ACPI: Lid Switch [LID]
[ 7.746714] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[ 7.746725] ACPI: Power Button [SLPB]
[ 7.746874] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 7.746880] ACPI: Power Button [PWRF]
[ 7.749494] ACPI: Battery Slot [BAT0] (battery present)
[ 7.749951] ACPI: AC Adapter [AC0] (on-line)
[ 7.755509] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.961538] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 8.061752] [drm] Initialized drm 1.1.0 20060810
[ 8.296521] cfg80211: Calling CRDA to update world regulatory domain
[ 8.319199] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 8.319231] r8169 0000:05:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 8.320035] r8169 0000:05:00.0 eth0: RTL8105e at 0xffffc90000032000, 38:60:77:69:8f:16, XID 00a00000 IRQ 29
[ 8.363138] kvm: Nested Virtualization enabled
[ 8.363151] kvm: Nested Paging enabled
[ 8.704039] [drm] radeon kernel modesetting enabled.
[ 8.794078] r8169 0000:05:00.0 enp5s0: renamed from eth0
[ 8.832358] AMD IOMMUv2 driver by Joerg Roedel <[email protected]>
[ 8.832364] AMD IOMMUv2 functionality not available on this system
[ 8.959092] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
[ 8.961187] snd_hda_codec_hdmi: unknown parameter 'index' ignored
[ 8.965010] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card1/input8
[ 9.031523] media: Linux media interface: v0.10
[ 9.102014] CRAT table not found
[ 9.102024] Finished initializing topology ret=0
[ 9.102177] kfd kfd: Initialized module
[ 9.102941] checking generic (c0000000 3d0000) vs hw (c0000000 10000000)
[ 9.102951] fb: switching to radeondrmfb from VESA VGA
[ 9.103002] Console: switching to colour dummy device 80x25
[ 9.104030] [drm] initializing kernel modesetting (SUMO 0x1002:0x9647 0x1179:0xFC62).
[ 9.104059] [drm] register mmio base: 0xFEB00000
[ 9.104063] [drm] register mmio size: 262144
[ 9.104144] ATOM BIOS: Toshiba
[ 9.104219] radeon 0000:00:01.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used)
[ 9.104227] radeon 0000:00:01.0: GTT: 1024M 0x0000000020000000 - 0x000000005FFFFFFF
[ 9.104231] [drm] Detected VRAM RAM=512M, BAR=256M
[ 9.104235] [drm] RAM width 32bits DDR
[ 9.104379] [TTM] Zone kernel: Available graphics memory: 3821360 kiB
[ 9.104390] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 9.104394] [TTM] Initializing pool allocator
[ 9.104407] [TTM] Initializing DMA pool allocator
[ 9.104455] [drm] radeon: 512M of VRAM memory ready
[ 9.104459] [drm] radeon: 1024M of GTT memory ready.
[ 9.104497] [drm] Loading SUMO Microcode
[ 9.124664] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000, board id: 3655, fw id: 582762
[ 9.124685] psmouse serio1: synaptics: Toshiba Satellite L775D detected, limiting rate to 40pps.
[ 9.160285] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 9.170455] Linux video capture interface: v2.00
[ 9.179293] mousedev: PS/2 mouse device common for all mice
[ 9.223473] [drm] Internal thermal controller without fan control
[ 9.223622] [drm] Found smc ucode version: 0x00011200
[ 9.223730] [drm] radeon: dpm initialized
[ 9.266919] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 9.282200] [drm] PCIE GART of 1024M enabled (table at 0x0000000000274000).
[ 9.282345] radeon 0000:00:01.0: WB enabled
[ 9.282349] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000020000c00 and cpu addr 0xffff88009b70ac00
[ 9.282351] radeon 0000:00:01.0: fence driver on ring 3 use gpu addr 0x0000000020000c0c and cpu addr 0xffff88009b70ac0c
[ 9.283078] radeon 0000:00:01.0: fence driver on ring 5 use gpu addr 0x0000000000072118 and cpu addr 0xffffc90010f32118
[ 9.283081] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 9.283082] [drm] Driver supports precise vblank timestamp query.
[ 9.283084] radeon 0000:00:01.0: radeon: MSI limited to 32-bit
[ 9.283121] radeon 0000:00:01.0: radeon: using MSI.
[ 9.283145] [drm] radeon: irq initialized.
[ 9.298245] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 9.298931] rtlwifi: rtlwifi: wireless switch is on
[ 9.299718] [drm] ring test on 0 succeeded in 1 usecs
[ 9.299728] [drm] ring test on 3 succeeded in 3 usecs
[ 9.307045] sound hdaudioC0D2: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 9.307049] sound hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 9.307053] sound hdaudioC0D2: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 9.307055] sound hdaudioC0D2: mono: mono_out=0x0
[ 9.307058] sound hdaudioC0D2: inputs:
[ 9.307061] sound hdaudioC0D2: Mic=0x18
[ 9.307065] sound hdaudioC0D2: Internal Mic=0x12
[ 9.315899] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/sound/card0/hdaudioC0D2/input9
[ 9.316387] input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[ 9.316507] input: HD-Audio Generic Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[ 9.349814] [drm] ring test on 5 succeeded in 1 usecs
[ 9.369840] [drm] UVD initialized successfully.
[ 9.370279] [drm] ib test on ring 0 succeeded in 0 usecs
[ 9.370314] [drm] ib test on ring 3 succeeded in 0 usecs
[ 9.524205] rtl8192ce 0000:04:00.0 wlp4s0: renamed from wlan0
[ 9.769931] uvcvideo: Found UVC 1.00 device TOSHIBA Web Camera - MP (04f2:b289)
[ 9.788893] input: TOSHIBA Web Camera - MP as /devices/pci0000:00/0000:00:13.2/usb5/5-4/5-4:1.0/input/input12
[ 9.789309] usbcore: registered new interface driver uvcvideo
[ 9.789319] USB Video Class driver (1.1.1)
[ 9.871399] cfg80211: World regulatory domain updated:
[ 9.871412] cfg80211: DFS Master region: unset
[ 9.871417] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.871425] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.871431] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.871436] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.871441] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 9.871447] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.871453] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.871457] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.871463] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.890507] [drm] ib test on ring 5 succeeded
[ 9.911771] [drm] radeon atom DIG backlight initialized
[ 9.911776] [drm] Radeon Display Connectors
[ 9.911777] [drm] Connector 0:
[ 9.911779] [drm] VGA-1
[ 9.911780] [drm] HPD2
[ 9.911782] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[ 9.911783] [drm] Encoders:
[ 9.911784] [drm] CRT1: INTERNAL_UNIPHY2
[ 9.911786] [drm] CRT1: NUTMEG
[ 9.911787] [drm] Connector 1:
[ 9.911788] [drm] LVDS-1
[ 9.911789] [drm] HPD1
[ 9.911790] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 9.911791] [drm] Encoders:
[ 9.911792] [drm] LCD1: INTERNAL_UNIPHY2
[ 9.911793] [drm] LCD1: TRAVIS
[ 9.911794] [drm] Connector 2:
[ 9.911795] [drm] HDMI-A-1
[ 9.911796] [drm] HPD5
[ 9.911798] [drm] DDC: 0x6470 0x6470 0x6474 0x6474 0x6478 0x6478 0x647c 0x647c
[ 9.911799] [drm] Encoders:
[ 9.911800] [drm] DFP1: INTERNAL_UNIPHY1
[ 10.016569] [drm] fb mappable at 0xC0478000
[ 10.016576] [drm] vram apper at 0xC0000000
[ 10.016578] [drm] size 5787648
[ 10.016580] [drm] fb depth is 24
[ 10.016582] [drm] pitch is 6400
[ 10.016970] fbcon: radeondrmfb (fb0) is primary device
[ 10.078763] Adding 8388604k swap on /dev/sda2. Priority:-1 extents:1 across:8388604k FS
[ 10.143532] Console: switching to colour frame buffer device 200x56
[ 10.150308] radeon 0000:00:01.0: fb0: radeondrmfb frame buffer device
[ 10.150312] radeon 0000:00:01.0: registered panic notifier
[ 10.164191] [drm] Initialized radeon 2.40.0 20080528 for 0000:00:01.0 on minor 0
[ 10.194853] cfg80211: Calling CRDA for country: US
[ 10.231380] cfg80211: Regulatory domain changed to country: US
[ 10.231393] cfg80211: DFS Master region: FCC
[ 10.231397] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.231406] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 10.231413] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 10.231419] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 10.231425] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 10.231429] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm), (0 s)
[ 10.231434] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 10.231439] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 10.422003] XFS (sda3): Mounting V5 Filesystem
[ 10.837256] XFS (sda3): Ending clean mount
[ 10.899226] systemd-journald[187]: Received request to flush runtime journal from PID 1
[ 11.195453] microcode: CPU0: new patch_level=0x03000027
[ 11.195496] microcode: CPU1: new patch_level=0x03000027
[ 11.195601] microcode: CPU2: new patch_level=0x03000027
[ 11.195693] microcode: CPU3: new patch_level=0x03000027
[ 12.465476] IPv6: ADDRCONF(NETDEV_UP): wlp4s0: link is not ready
[ 13.726328] wlp4s0: authenticate with 00:1e:2a:6f:46:f8
[ 13.745730] wlp4s0: send auth to 00:1e:2a:6f:46:f8 (try 1/3)
[ 13.753012] wlp4s0: authenticated
[ 13.755130] wlp4s0: associate with 00:1e:2a:6f:46:f8 (try 1/3)
[ 13.758031] wlp4s0: RX AssocResp from 00:1e:2a:6f:46:f8 (capab=0x411 status=0 aid=3)
[ 13.758283] wlp4s0: associated
[ 13.758302] IPv6: ADDRCONF(NETDEV_CHANGE): wlp4s0: link becomes ready
[ 23.961417] PM: Syncing filesystems ... done.
[ 24.305227] PM: Preparing system for mem sleep
[ 24.310243] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 24.311535] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 24.311542] PM: Entering mem sleep
[ 24.311898] Suspending console(s) (use no_console_suspend to debug)
[ 24.320753] wlp4s0: deauthenticating fSuspend has always been problematic under Linux. It seems to be hit or miss for the most part, but here are some things you can try:
Use an LTS kernel, tuxonice, pm-utils, etc. See Suspend and Hibernate
Try a different graphics driver
Tweak the driver module parameters or build your own driver.
Unfortunately I don't have experience with the radeon driver, so I can only give you ideas. -
HDMI does not come back after disconnect
Hello Archers,
this one is bugging me for a while now, perhaps someone has an idea.
I have a headless ARCH home server that mainly has the following purposes:
1. being a 24/7 file/backup/ssh server for family and friends
2. being an MPD server connected to my music system
The setup may seem a bit exotic. The computer is connected to the music system via HDMI over an S/PDIF audio extractor to the music system. This is because the machine replaced a RaspberryPi that really had crappy analog audio output and my music system has an optical input and can perform the digital to analog conversion itself. I have not installed Pulse just alsa and jack2-dbus.
aplay -l shows the following:
**** Liste der Hardware-Geräte (PLAYBACK) ****
Karte 0: PCH [HDA Intel PCH], Gerät 0: ALC887-VD Analog [ALC887-VD Analog]
Sub-Geräte: 1/1
Sub-Gerät #0: subdevice #0
Karte 0: PCH [HDA Intel PCH], Gerät 3: HDMI 0 [HDMI 0]
Sub-Geräte: 0/1
Sub-Gerät #0: subdevice #0
The Problem:
Whenever I switch off the music system and later switch it back on, the HDMI-connection is lost and does not get reestablished. I tried various things but essentially only a reboot of the machine helps (which opposes purpose 1 of the machine). On the RaspberryPi I did not have that problem, probably due to the hdmi_force_hotplug=1 in /boot/config.txt.
My Observations so far:
The first problem that made the sound disappear was the screen blanker on the console after 10 minutes. This can be prevented with
setterm --term linux --blank 0 >/dev/tty1 # You need write permission on /dev/tty1 for this to work!
There are no appearant error or warning messages when using e.g. aplay or speaker-test, just no sound at all
There are tipps in the forums/the internet sugesting to disable power management on the display involving xset and xrandr. However, I have no X running and the tools complain that they cannot find/open the display
In /proc/asound/PCH/codec#2 I find the HDMI codec to show the following as long as it is connected after a reboot:
Codec: Intel Valleyview2 HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862882
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D3
Power: setting=D0, actual=D0
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
Device: name="HDMI 0", type="HDMI", device=3
Converter: stream=8, channel=0
Digital: Enabled GenLevel
Digital category: 0x2
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1e]: 16 20 24 32
formats [0x5]: PCM AC3
Power states: D0 D3
Power: setting=D0, actual=D0
Node 0x04 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="HDMI/DP,pcm=3 Jack", index=0, device=0
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Control: name="ELD", index=0, device=3
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=01, enabled=1
Power states: D0 D3
Power: setting=D0, actual=D0
Connection: 2
0x02* 0x03
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x80]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x58560020: [N/A] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D3
Power: setting=D0, actual=D0
Connection: 2
0x02 0x03*
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x80]
Pincap 0x09000094: OUT Detect HBR HDMI DP
Pin Default 0x58560030: [N/A] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D3
Power: setting=D0, actual=D0
Connection: 2
0x02 0x03*
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono
After disconnect/reconnect it changes to this:
Codec: Intel Valleyview2 HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862882
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
N/A
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power: setting=UNKNOWN, actual=UNKNOWN, Error, Clock-stop-OK, Setting-reset
Invalid AFG subtree
I figured that the problem is probably related to powermanagement, so I experimented with powertop. This resulted in a reduced consumption of 1W when idle, which is nice but did not solve the original problem...
The Questions
Is there a way to completely reinit the HDMI subsystem just like on a reboot?
Is there an option comparable to hdmi_force_hotplug=1 on the pi that forces the HDMI signal to stay up?
Thank You for Your time!
Best regards,
LarsI can confirm what zofiel said. I have tested it by connecting a TV and HDMI reactivitated by switching from X to console. However, this option only works one time and requires X running in the first place, which I usually have not on a headless server, but it made me think: Obviousely the X server needs to activate the graphics in the first place. Then I came up with an idea for a really messy work around. I could try to remotely start X. Normally, this is not possible and you get:
% startx
/usr/lib/xorg-server/Xorg.wrap: Only console users are allowed to run the X server
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server error
You can force it to work:
sudo startx
You get lots of error messages, but HDMI audio is back, even if one kills the X process afterwards with Ctrl+C (Audio stops, but resumes two seconds later). The downside is that starting X with sudo messes up permissions with the x related files in your home directory and you will have problems to use startx afterwards, so it is probably better to use su instead of sudo. If root does not have a properly configured .xinitrc file then one can also just execute the desktop environment directly e.g., for XFCE:
su - root -c "startxfce4"
Then kill it with Ctrl+C and you should have HDMI Audio working.
So now I could pack this in a script followed by some command to kill it, but, well, it is an ugly workaround
Is there really no better way? -
Satellite A30 does not come back after hibernation.
If I don't touch the keys for 10 mins or so my laptop goes into hibernation. It will normally come back when I touch a key or the touch pad but sometimes nothing I do can get it back. I have to turn it off and then back on again. I was wondering if anyone had any ideas?
I looked at the power management and I can turn off all hibernation but I like it to hibernate when I close the lid so is there any way to make it so it ONLY hibernates when I close the lid and at no other time?HI Clare,
In the Toshiba Power Management utility you should click on the 'advanced' tab and about half way down the resultant window you should see an option for the action to be taken when you close the lid of your SA30.
Make sure that this is set to 'hibernate'. Then go to the power save modes and click on the 'details' tab and then the 'Power Save Mode' tab and make sure that the 'Hibernate' option is set to 'never'.
With these settings your notebook should go into 'hibernate' when you close the lid but not at any other time.
Note that you can set the notebook to hibernate when running on battery when the bttery capacity reaches a pre-set value of your own choosing.
regards, -
IMac screen will not come on after sleep
iMac screen does not come on after sleeping for a period of time - twice now from overnight. The back seems to be warm. I have to hold the on button until I hear the drive and system shut down. Then after period of time it will start just fine. ?????
I know that some of the older imacs had overheating problems that caused unexpected sleep. try to keep the display darker and keep the room not too hot. That seems to usually solve the issue.
-
Host Command does not come back
Hi,
I have treid to export schema by pressing a button, (form designed in Form10gR2 and excute via Application Server R2. )
For this I have applied one by one these syntaxes
1) host ( 'cmd /C start "" "'|| exp USERID=SYSTEM/MANAGER@ora11 OWNER=scott,hr FILE=E:\JAN10.DMP');
2) host ( 'cmd /C exp USERID=SYSTEM/MANAGER@ora11 OWNER=scott,hr FILE=E:\JAN10.DMP');
3) client_host('exp USERID=SYSTEM/MANAGER@ora11 OWNER=scott,hr FILE=E:\JAN10.DMP');
4) WEBUTIL_HOST.NONBLOCKING('exp USERID=SYSTEM/MANAGER@ora11 OWNER=scott,hr FILE=E:\JAN10.DMP');
When my client/ user executes the command, session goes hang and application screen does not come back. If I execute the exp command directly from the Application Server Command Prompt then exp works.
Please help me, what is the syntax to get the dump wihtout hanging the session.
Database 11g Linux
Application Server 10R2 Window2003.
Developer 10gR2.
Client Windows , Explorer, FireFox etc.
Regards.
Priya.Hi Priya,
It is always a better practice to call a batch file using the host command instead of hardcoding the command inside form. Which would help you to modify the batch file for any changes, without re-compiling the forms.
In this case, create a batch script, which would set the ORACLE_HOME etc (to make sure the exp command is recognized, you need to add the DB ORACLE_HOME/bin to the PATH), and then call the command to export. You can also parameterize the batch script and pass the parameters from form, separated by space.
-Arun -
CQ62-215DX hybernates upon closing notebook and does not come back on after opening screen again
My CQ62-125DX Product WQ5856UA#ABA shut down when book was closed in the on position. The screen remains black athough Cap lock light s intermitent. I shut down to reboot, and system sounds and acts as if t was coing o, but screen never lights up.
This happened only after the laptop screen was closed and reopened. after giving up I decided to press the power button three week later, and it came on, but thinking all was Ok after a couple of days, again I closed the laptop and screen will not come back on upon opening. It seems to gointo hybernate mode, but will not wake up again. If it happens to come on again I will go in and shut off the energy saving featues, so it does not go into hybernatiion, but mean while...... What fix do you have for this issue. I'm not doing anythingut of the ordinary, I look online, and see that many people experience these symptoms. Have you looked into this and figured how to solve this glitch?? Thanks in advance for you help ALbertSame thing here!! I was calling my wife and it happened 3 times in a row in a matter of minutes. I rebooted the phone and it went away. Hasn't crept up on me again, yet (knock on wood).
I don't know whether it makes a difference and whether they are technically the same, but I upgraded the firmware that was released 07/10/2008 that is from Apple's Servers from version 5A345 to 5A347 just to see if this fixed any last minute glitches.
I hope this problem never surfaces again. We all paid a lot for these and spent a lot of time waiting for activation. -
Just upgraded to latest iOS and my iPad does not come back up - the following appeared as the first thing after turning back on. It displays a line from the power/USB connector to an iTunes logo and then goes off and after some minutes comes back on. I cannot reset it or anything else. It is completely non-functional.
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Cheers, Tom -
Screen does not turn on after start up, but after standby on Satellite M100
Hi,
I have quite some experience with computers and laptops, but this problem exhausted all my knowledge.
My girlfriend has a Toshiba Satellite M100, PSMA1E. It runs Windows XP, currently on SP3.
The laptop always had shutdown/stand bye issues. It would go on stand bye and the screen would not come back. She usually would turn it off manually (holding the power button) and turn it on again.
Same thing happened last week, but with me. I turned it off holding the power button but when I turned it back on the screen was completely black. After a few attempts I realized that everything was working; I could hear XP booting and the usual sound files but there was no way I could get the screen working.
The strangest thing is that the CMOS/BIOS screen, the first one with the Toshiba logo, also does not show up. If it was a OS problem I thought I would be able to access the BIOS at least, but that doesn't work. Fn+F5 also doesn't work.
Then something even stranger happened. I was turning it on and off with keyboard shortcuts and I realized that if I put it on stand bye using shortcuts and then turn it back on the screen turns on perfectly fine (there is some resolution adjustment cause icons are out of place, but it works perfectly well).
From that on I tried everything I know. BIOS update, all Windows XP updates, all Toshiba QuickFix, cleaning the registry with different tools, uninstalling and reinstalling the video driver (ATI Radeon X1400), HotKeys utility, Power Saver Utility, Toshiba Hardware Tools, looking at start up programs, services, everything I could possibly think off.
What really puzzles me is that the Toshiba start up screen won't show up. I can't access the BIOS, but I tried restoring BIOS standard values through Toshiba Hardware Tools. It didn't work. I don't even know if reinstalling XP will work because every time I turn it on it's all black and I need to do the stand bye/turn back on trick.
When I plugged it on a external monitor I could see the whole start up process (BIOS initial screen and Windows). I then tried to access the display configuration of the video driver but it would only show the external monitor. It would only detect the laptop screen after a stand bye/turn back on, and then it worked perfectly well: two simultaneous screens, extended screen, everything. Ah, changing the BIOS from Auto-Select to LCD+external monitor also does not work.
I'm really puzzled here and I can't figure this one out. I really don't think it's a hardware issue, because the screen works 100% after the stand bye. I guess XP is making something during shut down that completely 'shuts down' my screen, even after boot, and then I can only turn it on with the stand bye thing.
Any help would be really appreciated!
Best,Hi mate,
that whole story sounds really weirdo since after reading all this and knowing that youve tried almost everything doesnt makes it better.. :/
Usually I would say: update your BIOS, but you already updated everything. This problem could be BIOS related since the initialization of the hardware after a standby is controlled by the chipset trough the BIOS.
I guess it could also be something with the background light of the LCD screen (failed initialization after waking up), you can check this by reproducing the situation with the black screen and holding some light near the screen. If you can see some schemes on the screen (something like desktop, etc..) then it could be the background lighting. In such case try to reinstall the operating system and update all installed drivers to the newest version (yes I know, sounds like more pain).
Otherwise, click [HERE|http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT], find the nearest authorized service partner in your country, contact them and ask them for a hardwarecheckup. Maybe its really a hardware related issue..
Greets and good luck -
Laptop screen does not come on
My 1 year, 1 month old pavillion dv4 laptop\'s screen does not come on. At first I thought it was the screen. However after geek squad and one other computer repair place diagnosed it, they said it needs the motherboard replaced.
I currently have the laptop hooked up to a external monitor and it works fine in safe mode. Any suggestions where I can get a motherboard?Hi there ,
Try Hard Reset
Link is given Below :
HARD RESET
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem**** -
Hi, My iphone 5 loses the 3G connections everytime i go into tunnel and also to holland park and it does not come back untill i restart the phone? i dont know why is it happening?
Hi, beth.lau.gr.
Thank you for visiting Apple Support Communities.
I understand you have been experiencing issues with your iPhone restarting and showing you a blue screen. I wont be able to give you an exact answer as to why this is happening. However, this is the most relevant troubleshooting article for this issue. This article also provides options to reach out to us via phone for additional assistance.
If your iOS device restarts, displays the Apple logo, or powers off while you're using it
http://support.apple.com/en-us/HT203899
Cheers,
Jason H.
Maybe you are looking for
-
Multiple users accessing the same data in a global temp table
I have a global temp table (GTT) defined with 'on commit preserve rows'. This table is accessed via a web page using ASP.NET. The application was designed so that every one that accessed the web page could only see their data in the GTT. We have just
-
[Transport / CTS] Production servers on a different site than dev servers
Hello, My current customer has his development servers on a physical site A and his production servers on a physical site B (distance between the sites is 300kms). How can we do to tranport the developments and customizing from site A to site B. The
-
I have tried every answer and my iMessage still won't work!
-
Hello, I am working on an R12 implementation project. The legacy system is Oracle apps(11.5.x). I have to work on GL Balances converison. we want to get all the journal details from march 2009. i dont understand do we also get the balances since then
-
I'm trying to use a custom class loader to load specific classes (not handle everything). So in those particular situations I call my custom class loader's loadClass method which will first check for a .class file in a specific directory and use that