Sap 4.7ides istalation problem in my laptop.
I have hcl laptop with 2gb ram 250gb hd and core 2 duo processor .
But I got a problem when the database instance loading.
The problem is in the stage of DATABASE LOAD(POST PROCESSING) waiting 0 state cannot complete.It was remain unchanged.....
Hi,
Just pull 1 RAM stick out. By the way, what is your machine ? Is there any reason to mix them ???
Regards
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Similar Messages
-
Sneak Preview SAP NetWeaver 2004s istalation problem
Hy there,
I have an error on installing Sneak Preview SAP NetWeaver 2004s (ABAP)
The last lines in XCMDOUT.LOG are
ERROR 2006-04-19 08:46:28
The dbmcli call for action PARAM_INIT_INST failed. Check the logfile XCMDOUT.LOG.
ERROR 2006-04-19 08:46:28
The dbmcli call for action PARAM_INIT_INST failed. Check the logfile XCMDOUT.LOG.
ERROR 2006-04-19 08:46:28
FCO-00011 The step sdb_init_instance_type with step key |NW_ABAP_OneHost|ind|ind|ind|ind|0|0|NW_CreateDB|ind|ind|ind|ind|9|0|NW_ADA_DB|ind|ind|ind|ind|6|0|SdbPreInstanceDialogs|ind|ind|ind|ind|2|0|SdbInstanceDialogs|ind|ind|ind|ind|1|0|SDB_INSTANCE_CREATE|ind|ind|ind|ind|0|0|sdb_init_instance_type was executed with status ERROR .
Please hel me, I'm new in SAP
calin adrian comes
email: [email protected]Hi calin
There seems to be some problem with sp 16 max DB (version 7.6).
Please see this thread of the SDN forum
SP16 Preview: MaxDB Installation fails (Phase 6)
U will have to replace it with MAX DB ver7.5 .
If you find that ur problem is solved ,do not forget to reward points .
regards
rajeshkr -
Hi, recently purchased macbook 13", I have problem with sound when connect to my LG Smart tv with sound system. When i change sounds effect on my sound system also LG its all go quiet didn't have this problem with my laptop. Any advise ?
Some progess I see. To be honest, i would not waste your time with trying to connect using wireless.
You are likely to get poor connections and dropping out.
If its working using a cable, then there is no need to bother with giving me the network settings, bu see how it goes, because sometimes giving the TV a static IP address can give better results.
There is an example of a couple of powerline adapters on the diagram below. Just ignore the network switch unless you want to connect other devices which are near to the TV.
http://forumhelp.dyndns.info/networking/powerline3.jpg
I will monitor the subject line of this thread, should you want to post any more information.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
Lightroom doesn't recognize mine camera, the Nikon D800 E to shoot tethering. There is no problem with mine laptop. Can you help me with this issue?
Ronald ( the Netherlands)Sure the laptop know's that the Nikon D800E is connected, but lightroom doesn't recognise this camera. Two weeks a go it wasn't a problem at all.
-
SAP Adapter has a problem, SOD violations will not be checked
Hi,
In our ides server whenever i click save button in su01 i get the following error ,
"SAP Adapter has a problem, SOD violations will not be checked !
Please check with your system Administrator
Technical Info:
Error when opening an RFC connection "
we didn't have this problem before . can anybody help me to resolve the issue
Also I am getting this error only if I click save in su01. in other t code. I don't get this error
Thanks in Advance
Edited by: gajula jhansi on Apr 11, 2011 11:28 AMYou need to restart your sap adapter in GRC front end from configurations tab-->Sap adapter >choose the one for your back end system> if it's grayed out or even green still, click on it and let it restart and turn green again.
Then you go back to your backend ECC system and in SM59 , choose the RFC connection for the Risk Terminator (the one you have saved in the Risk Terminator transaction /VIRSA/ZRTCNFG in backend system).. and test the connection. It should pass the connection test if your adapter is working and set up correctly. Then when you do save in SU01 or make changes in PFCG and have Risk Terminator activated for the backend system, it will check the SOD violations against those transactions from RAR front end.
If you don't want Risk Terminator to check for SOD violations in front end RAR, then you need to set your settings to 'NO' for all in the Risk Terminator transaction. You can get all this info in the GRC config guide for RAR and SPM area.
Regards,
Alley -
Every time I try to download iTunes onto my Vaio laptop it only downloads partially, then claims to be finished. Is this a problem with my laptop or with iTunes?
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards? -
Problems with my laptop starting - Satellite P745, Windows 7
For the past few months I've been having a very strange problem with my laptop. I have a Satellite P745-S4380 with Windows 7. There are times that I can shut it down and turn it on with no problems. However, a majority of the time when I shut my computer down, it will not turn back on. When I push the power button, the following happens:
the power button lights up
the fan starts running
I never see the "Toshiba" screen and my computer does not start
The only way I've gotten my computer to turn back on is to either:
1) unplug my power and let my computer run in this "fan running, power light on" mode until the battery dies - then generally when I plug it back in, it will start right up
or
2) wait 5 to 7 days, then it will start right up
I don't use it on a daily (or even weekly) basis because I am on the computer all day at work, but I would have to guess this started around June. I'm trying to determine if this is something like a motherboard failure, or if it's some sort of software/hardware update that is not setting well with my machine. Has anyone else had this issue? Any ideas on things to even try troubleshooting? I think it may be related to an update or setting (maybe because I don't want it to be the motherboard) because even if I go to reboot it at times, it will shut down but will not come up and it will get hung in the same state as I described above. If my motherboard is bad, would it act like this? I'm at a loss with where to even start...
Something else to mention is that if I put it in "hibernate" mode, I haven't seen this issue.Hi ! There are many discussions about whether you should shut your PC down or just leave it run. I never allow my PC to go into sleep or hibernate mode. I allow my monitor to shut down after 15 minutes of no activity. I turn my wireless mouse off when I'm done with my PC. When I return to my PC, I turn my mouse on and my PC starts up immediately. That is the way I use my lap top. It's a choice for you to make. I have no proof it it is good or bad practice. Of course this would need to be changed if your operating only on battery.
Dokie!!
http://www.howtogeek.com/128507/htg-explains-should-you-shut-down-sleep-or-hibernate-your-laptop/
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.
Attachments:
Capture48.JPG 146 KB -
I had problems with my laptop which have now been fixed but I am now unable to download or connect to my Itunes account through any of my devices?
An iTunes account is nothing more than a login and password.
The media is only where the user put it. Restore the ENTIRE iTunes folder from the backup of the computer. -
Problem with my laptop colour changing and some time moniter screen black out
i have a problem with my laptop screen some time its working ok but some time its going to changing and blinking colours and screen shows black out and not respend for 10 minutes or more.i want a solution for this.
Hi @hpsah
Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see that you are having a problem with your laptop screen changing and blinking through colours. I will be happy to help find a solution for this but you didn't give me information to work with. For future posts I suggest checking out Want Good Answers? Ask Good Questions. I will need to know what operating system you are using? What is the product number of the notebook? Does this issue happen if you connect an external monitor?
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP -
I already encountered this problem in version 6.40, that's why I installed 7.10 (patchlevel 3). It runs on a laptop with Windows XP Professional SR2.
I may have several sessions open connected to 1 or more different SAP instances (all 4.6C). Very often when I switch between sessions either via the task bar or using alt-Tab I all of a sudden loose all my sessions and I have to connect all over again. The Sap Logon Icon remains visible in the System tray until you hover the mouse over it, then it disappears too.
Does anyone recognize this problem and hopefully has a solution for it?
Any help is mych appreciated!!
Ton TeunsYou try install path 32
go to: https://forums.sdn.sap.com/click.jspa?searchID=19954340&messageID=6264618
or
you back to the version old
t-code se38 -- UtilitiesSettings changed the radiobutton to Front End editor (old), because your version of SAP GUI path < 32 you obtain dump if you select the Front End editor (new)
I hope that this it help you
Cordial greetings. -
Export SAP GUI Logon system properites to another laptop
Hi, SDN Fellows.
I want to run SAP GUI logon systems in another laptop. After installing a new SAP GUI client. Instead of re-add the logon system properties, is that a way I can export and import from another laptop? Say I have 10 logon system properties (some with application server and some with logon groups), how do I pick the 8 of 10, and export to another SAP GUI in another laptop?
Thanks,
KentHello Kent,
for SAP GUI for Windows 6.20 or 6.40, please have a look at [SAP note 512040|https://service.sap.com/sap/support/notes/512040], for SAP GUI for Windows 7.10 refer to [SAP note 1035560|https://service.sap.com/sap/support/notes/1035560] and for SAP GUI for Java please read chapter 7 of the manual included in the SAP GUI for Java installation.
Best regards
Rolf-Martin -
SAP 4.7 Installation problem on Solaris 10 - Oracle 9.2.0.7
Hi,
I am trying to install SAP 4.7 on Solaris 10 - Oracle 9.2.0.7. I am using standar installation DVD for SAP 4.7 SR1. After installation I want to login SAP system I have an error about database inconsistency. System said that enter SICK transaction. I entered SICK and my error is "OS release SunOS 5.10 Generic_141444-09 sun4u is not support with this kernel". After I received this error I installed new kernel (221) and I upgaded kernel to 221. But after that I could not open SAP system. I checked dev_w1 and it is like below:
"dev_w1" 456 lines, 18662 characters
trc file: "dev_w1", trc level: 1, release: "640"
ACTIVE TRACE LEVEL 1
ACTIVE TRACE COMPONENTS all, M
M sysno 00
M sid KZP
M systemid 370 (Solaris on SPARCV9 CPU)
M relno 6400
M patchlevel 0
M patchno 221
M intno 20020600
M make: single threaded, Unicode, 64 bit
M pid 22022
M
M
M Fri Jan 29 15:11:00 2010
M ***LOG Q01=> tskh_init, WPStart (Workproc 1 1 22022) [thxxhead.c 1144]
M calling db_connect ...
C Got ORACLE_HOME=/oracle/KZP/920_64 from environment
C got NLS_LANG='AMERICAN_AMERICA.UTF8' from environment
C Client NLS settings: AMERICAN_AMERICA.UTF8
C Logon as OPS$-user to get SAPKZP's password
C Connecting as /@KZP on connection 0 (nls_hdl 0) ... (dbsl 640 070208)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 0x10667d250 0x10668fcd0 0x10668f668
C Attaching to DB Server KZP (con_hdl=0,svchp=0x10668f598,srvhp=0x106691dc8)
C Starting user session (con_hdl=0,svchp=0x10668f598,srvhp=0x106691dc8,usrhp=0x10669a800)
C Now '/@KZP' is connected: con_hdl=0, nls_hdl=0, session_id=13.
C Got SAPKZP's password from OPS$-user
C Disconnecting from connection 0 ...
C Close user session (con_hdl=0,svchp=0x10668f598,usrhp=0x10669a800)
C Now I'm disconnected from ORACLE
C Connecting as SAPKZP/<pwd>@KZP on connection 0 (nls_hdl 0) ... (dbsl 640 070208)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 0x10667d250 0x10668fcd0 0x10668f668
C Starting user session (con_hdl=0,svchp=0x10668f598,srvhp=0x106691dc8,usrhp=0x10669a800)
C Now 'SAPKZP/<pwd>@KZP' is connected: con_hdl=0, nls_hdl=0, session_id=13.
C Database NLS settings: AMERICAN_AMERICA.UTF8
C DB instance KZP is running on sapkzpn2 with ORACLE version 9.2.0.7.0 since JAN 29, 2010, 15:10:46
B Connection 0 opened (DBSL handle 0)
B Wp Hdl ConName ConId ConState TX PRM RCT TIM MAX OPT Date Time DBHost
B 000 000 R/3 000000000 ACTIVE NO YES NO 000 255 255 20100129 151100 sapkzpn2
M db_connect o.k.
M ICT: exclude compression: .zip,.cs,.rar,.arj,.z,.gz,.tar,.lzh,.cab,.hqx,.ace,.jar,.ear,.war,.css,.pdf,.js,.gzip
,.uue,.bz2,.iso,.sda,.sar,.gif
I
I Fri Jan 29 15:11:07 2010
I MtxInit: 1 0 0
M SHM_PRES_BUF (addr: 0xffffffff7597a000, size: 4400000)
M SHM_ROLL_AREA (addr: 0xfffffffe56000000, size: 134217728)
M SHM_PAGING_AREA (addr: 0xffffffff62000000, size: 67108864)
M SHM_ROLL_ADM (addr: 0xffffffff75db0000, size: 2672386)
M SHM_PAGING_ADM (addr: 0xffffffff71f00000, size: 656416)
M ThCreateNoBuffer allocated 572152 bytes for 1000 entries at 0xfffffffe4e004000
M ThCreateNoBuffer index size: 3000 elems
M ThCreateVBAdm allocated 12176 bytes (50 server) at 0xffffffff7bc00000
X EmInit: MmSetImplementation( 2 ).
X <ES> client 1 initializing ....
X Using implementation std
X ES initialized.
B db_con_shm_ini: WP_ID = 1, WP_CNT = 8, CON_ID = -1
B dbtbxbuf: Buffer TABL (addr: 0xffffffff60000100, size: 30000000, end: 0xffffffff61c9c480)
B dbtbxbuf: Buffer TABLP (addr: 0xffffffff6d400100, size: 10240000, end: 0xffffffff6ddc4100)
B dbexpbuf: Buffer EIBUF (addr: 0xfffffffe5f800108, size: 4194304, end: 0xfffffffe5fc00108)
B dbexpbuf: Buffer ESM (addr: 0xfffffffe5f000108, size: 4194304, end: 0xfffffffe5f400108)
B dbexpbuf: Buffer CUA (addr: 0xfffffffe5101e108, size: 3072000, end: 0xfffffffe5130c108)
B dbexpbuf: Buffer OTR (addr: 0xfffffffe5e800108, size: 4194304, end: 0xfffffffe5ec00108)
M rdisp/reinitialize_code_page -> 0
M icm/accept_remote_trace_level -> 0
M rdisp/no_hooks_for_sqlbreak -> 0
M CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
S
S Fri Jan 29 15:11:08 2010
S *** init spool environment
S initialize debug system
T Stack direction is downwards.
T debug control: prepare exclude for printer trace
T new memory block 0x106aa11e0
S spool kernel/ddic check: Ok
S using table TSP02FX for frontend printing
S 1 spool work process(es) found
S frontend print via spool service enabled
S printer list size is 150
S printer type list size is 50
S queue size (profile) = 300
S hostspool list size = 3000
S option list size is 30
S found processing queue enabled
S found spool memory service RSPO-RCLOCKS at 0xfffffffe51310070
S doing lock recovery
S setting server cache root
S found spool memory service RSPO-SERVERCACHE at 0xfffffffe513103c8
S using messages for server info
S size of spec char cache entry: 297032 bytes (timeout 100 sec)
S size of open spool request entry: 2272 bytes
S immediate print option for implicitely closed spool requests is disabled
A
A Fri Jan 29 15:11:09 2010
A
A -PXA--
A PXA INITIALIZATION
A System page size: 8kb, total admin_size: 5512kb, dir_size: 5480kb.
I *** ERROR => shmget(10006,153600000,2016) (22: Invalid argument) [shmux.c 1525]
A RABAX in run level 1
A RABAX in unkown environment: task_type=0, run level=1, rabax state=80000000 ztta_task_type=0
[0] DoStack2 ( 0x105af7010, 0xffffffff7fffd740, 0x1004a4ae4, 0x0, 0x105dbb180, 0x102e2f6e0 ), at 0x1004a4ae4
[1] CTrcStack2 ( 0x1036f6d60, 0x0, 0x17400, 0x102e947dc, 0x0, 0x102e2f6e0 ), at 0x1004a4680
[2] __1cXrabax_CStackToTraceFile6F_v_ ( 0x0, 0x1, 0x0, 0x3097000, 0x100000000, 0x103097058 ), at 0x100ae0e80
[3] __1cKrabax_init6FpkH_v_ ( 0x102002ad8, 0x0, 0x1, 0x0, 0x0, 0x0 ), at 0x100ad97d8
[4] ab_rabax ( 0x0, 0x80000000, 0x6da, 0x103879400, 0x1880, 0x1065e4110 ), at 0x100acfe3c
[5] __1cJab_pbinit6F_v_ ( 0x100000000, 0x102e947dc, 0x1, 0x102002ab4, 0x102f4e1c0, 0x103815550 ), at 0x100750de0
[6] ab_init ( 0x0, 0x5bd5000, 0xac8800, 0x5bd5000, 0x1, 0x0 ), at 0x100ac8d34
[7] ThrInitRunTime ( 0x100489c00, 0x489c00, 0x332c400, 0x102e94820, 0x1, 0x102e947d4 ), at 0x100476e84
[8] ThStartUp2 ( 0x101fec800, 0x194c800, 0x100000000, 0x102e947d4, 0x0, 0x10194cc00 ), at 0x100415860
[9] tskh_init ( 0x2e7a000, 0x1, 0x1, 0x540, 0x102e94400, 0x15 ), at 0x100260f14
[10] tskhstart ( 0x0, 0x2e94400, 0x0, 0x1003d6400, 0x3d6400, 0x100000000 ), at 0x10025cf9c
[11] DpMain ( 0x3641400, 0x2e7a000, 0x100000000, 0x1, 0x0, 0x0 ), at 0x1001856c0
A
A Fri Jan 29 15:11:10 2010
A TH VERBOSE LEVEL FULL
A ** RABAX: level LEV_RX_PXA_RELEASE_MTX entered.
A ** RABAX: level LEV_RX_PXA_RELEASE_MTX failed.
A *** suicide ON
A ** RABAX: level LEV_RX_VMIT_CLEANUP entered.
A ** RABAX: level LEV_RX_VMIT_CLEANUP completed.
A ** RABAX: level LEV_RX_ROLLBACK entered.
A ** RABAX: level LEV_RX_ROLLBACK completed.
A ** RABAX: level LEV_RX_DB_ALIVE entered.
A ** RABAX: level LEV_RX_DB_ALIVE completed.
A ** RABAX: level LEV_RX_HOOKS entered.
A ** RABAX: level LEV_RX_HOOKS completed.
A ** RABAX: level LEV_RX_STANDARD entered.
A ** RABAX: level LEV_RX_STANDARD failed.
A ** RABAX: level LEV_RX_C_STACK entered.
A ** RABAX: level LEV_RX_C_STACK completed.
A ** RABAX: level LEV_RX_MEMO_CHECK entered.
A ** RABAX: level LEV_RX_MEMO_CHECK completed.
A ** RABAX: level LEV_RX_INTERFACES entered.
A ** RABAX: level LEV_RX_INTERFACES completed.
A ** RABAX: level LEV_RX_GET_MESS entered.
A ** RABAX: level LEV_RX_GET_MESS completed.
A ** RABAX: level LEV_RX_INIT_SNAP entered.
A ** RABAX: level LEV_RX_INIT_SNAP completed.
A ** RABAX: level LEV_RX_WRITE_SYSLOG entered.
A ** RABAX: level LEV_RX_WRITE_SYSLOG completed.
A ** RABAX: level LEV_RX_WRITE_SNAP entered.
X *** ERROR => invalid MM administration (adm) (nil) (admCheck)(nil) [mmxx.c 2127]
A ** RABAX: level LEV_RX_WRITE_SNAP failed.
A ** RABAX: level LEV_RX_SET_ALERT entered.
A ** RABAX: level LEV_RX_SET_ALERT completed.
A ** RABAX: level LEV_RX_COMMIT entered.
A ** RABAX: level LEV_RX_COMMIT completed.
A ** RABAX: level LEV_RX_SNAP_SYSLOG entered.
A ** RABAX: level LEV_RX_SNAP_SYSLOG completed.
A ** RABAX: level LEV_RX_RESET_PROGS entered.
A ** RABAX: level LEV_RX_RESET_PROGS completed.
A ** RABAX: level LEV_RX_STDERR entered.
A Fri Jan 29 15:11:10 2010
A
A Error Code PXA_NO_SHARED_MEMORY.
A Module $Id: //bas/640_REL/src/krn/runt/abload3.c#44 $ SAP.
A Function ab_pbinit Line 1754.
A ** RABAX: level LEV_RX_STDERR completed.
A ** RABAX: level LEV_RX_RFC_ERROR entered.
A ** RABAX: level LEV_RX_RFC_ERROR completed.
A ** RABAX: level LEV_RX_RFC_CLOSE entered.
A ** RABAX: level LEV_RX_RFC_CLOSE completed.
A ** RABAX: level LEV_RX_IMC_ERROR entered.
A ** RABAX: level LEV_RX_IMC_ERROR completed.
A ** RABAX: level LEV_RX_DATASET_CLOSE entered.
A ** RABAX: level LEV_RX_DATASET_CLOSE completed.
A ** RABAX: level LEV_RX_RESET_SHMLOCKS entered.
A ** RABAX: level LEV_RX_RESET_SHMLOCKS failed.
A ** RABAX: level LEV_RX_ERROR_SAVE entered.
A ** RABAX: level LEV_RX_ERROR_SAVE completed.
A ** RABAX: level LEV_RX_ERROR_TPDA entered.
A ** RABAX: level LEV_RX_ERROR_TPDA completed.
A ** RABAX: level LEV_RX_PXA_RELEASE_RUDI entered.
A ** RABAX: level LEV_RX_PXA_RELEASE_RUDI completed.
A ** RABAX: level LEV_RX_LIVE_CACHE_CLEANUP entered.
A ** RABAX: level LEV_RX_LIVE_CACHE_CLEANUP completed.
A ** RABAX: level LEV_RX_END entered.
A ** RABAX: level LEV_RX_END completed.
A ** RABAX: end RX_SUICIDE
A Shared Memory von 150000 Kilo-Bytes f\303\274r PXA nicht verf\303\274gbar..
A
A *
A * Non recoverable error. Aborting process...
A *
M ***LOG R63=> ThWpHalt, halt wp () [thxxhead.c 15213]
M in_ThErrHandle: 1
M *** ERROR => ThWpHalt: halt wp (step 1, th_errno 5, action 2, level 1) [thxxhead.c 9696]
M
M Info for wp 1
M
M stat = 4
M reqtype = 1
M act_reqtype = -1
M rq_info = 0
M tid = 1
M mode = 0
M len = -1
M rq_id = 65535
M rq_source = 255
M last_tid = 0
M last_mode = 0
M int_checked_resource(RFC) = 0
M ext_checked_resource(RFC) = 0
M int_checked_resource(HTTP) = 0
M ext_checked_resource(HTTP) = 0
M report = > <
M action = 0
M tab_name = > <
M
M
M PfStatDisconnect: disconnect statistics
M ThIErrHandle: action changed to 2
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >SAP-Trace buffer write< for event BEFORE_DUMP
M TrThHookFunc: called for WP dump
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M *** ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c 730]
M *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed [thxxtool3.c 255]
M Entering ThSetStatError
M ThErrPrivHandle: set th_errno (5)
M Entering ThReadDetachMode
M *** ERROR => ThIErrHandle: bad value for th_act_em_hdl (5), detach T1/M0 [thxxhead.c 10129]
M
M Modeinfo for User T1/M0
M
M
M call ThrShutDown (1)...
A Saving PXA statistics.
M -
C-STACK -
[0] __1cNab_pxasavedir6F_i_ ( 0x102e94400, 0x2f63c00, 0x102e94800, 0x10200b800, 0x1, 0x0 ), at 0x10076c108
[1] ab_shutdown ( 0x0, 0x1, 0x102f3b400, 0x1, 0x102e94400, 0x2e94400 ), at 0x100aca150
[2] ThIErrHandle ( 0x10251b400, 0x2e94800, 0x102e7a324, 0x2, 0x2e94400, 0x102e94800 ), at 0x100293870
M -
M ***LOG Q0E=> SigIGenAction, signal ( 11) [sigux.c 902]
M in_ThErrHandle: 2
M ***LOG R0H=> ThIErrHandle, Loop in ThErrHandle, restart wp () [thxxhead.c 9717]
M -
C-STACK -
[0] DoStack2 ( 0x105af7010, 0xffffffff7fffc340, 0x1004a4ae4, 0x0, 0x105dbac40, 0x102e2f6e0 ), at 0x1004a4ae4
[1] CTrcStack2 ( 0x1036f6d00, 0x0, 0x17400, 0x102e947dc, 0x10049d16c, 0x102e2f6e0 ), at 0x1004a4680
[2] ThIErrHandle ( 0x0, 0x100000000, 0x3, 0x10331ff08, 0xb, 0x4 ), at 0x100291b08
[3] SigIGenAction ( 0x102c9f800, 0x1032acd04, 0x102c9f800, 0xb, 0x102e94820, 0x102e947d4 ), at 0x101e49c4c
[4] __sighndlr ( 0xb, 0xffffffff7fffcf80, 0xffffffff7fffcca0, 0x101e493bc, 0x0, 0x0 ), at 0xffffffff7c7d62e0
[5] call_user_handler ( 0xffffffff7d300200, 0xffffffff7d300200, 0xffffffff7fffcca0, 0x19, 0x0, 0x0 ), at 0xffffffff7c7c9e44
[6] sigacthandler ( 0x0, 0xffffffff7fffcf80, 0xffffffff7fffcca0, 0xffffffff7d300200, 0x0, 0xffffffff7c93c000 ), at 0xffffffff7c7ca03
c
[7] __1cNab_pxasavedir6F_i_ ( 0x102e94400, 0x2f63c00, 0x102e94800, 0x10200b800, 0x1, 0x0 ), at 0x10076c0f4
[8] ab_shutdown ( 0x0, 0x1, 0x102f3b400, 0x1, 0x102e94400, 0x2e94400 ), at 0x100aca150
[9] ThIErrHandle ( 0x10251b400, 0x2e94800, 0x102e7a324, 0x2, 0x2e94400, 0x102e94800 ), at 0x100293870
[10] __1cIrabax_do6FpkHpHi_v_ ( 0x102002ad8, 0x0, 0x41, 0x102e94800, 0x1, 0x1 ), at 0x100adc154
[11] ab_rabax ( 0x2, 0x2e94800, 0x1, 0x100000000, 0x2e94400, 0x2e94400 ), at 0x100ad3bc4
M -
M Fri Jan 29 15:11:11 2010
M ThSigHandler: signal (step 1, th_errno 11, action 4)
M
M Info for wp 1
M
M stat = 4
M reqtype = 1
M act_reqtype = -1
M rq_info = 0
M tid = 1
M mode = 0
M len = -1
M rq_id = 65535
M rq_source = 255
M last_tid = 0
M last_mode = 0
M int_checked_resource(RFC) = 0
M ext_checked_resource(RFC) = 0
M int_checked_resource(HTTP) = 0
M ext_checked_resource(HTTP) = 0
M report = > <
M action = 0
M tab_name = > <
M PfStatDisconnect: disconnect statistics
M Entering ThSetStatError
M ***LOG Q02=> wp_halt, WPStop (Workproc 1 22022) [dpuxtool.c 318]
Also I tried to change SAPEXE.SAR and SAPEXEDB.SAR files from SAP Kernel CD. After that I started installation again. But I have same error. SAP system didn't work.
How can I solve this error?Cannot I install SAP 4.7 SR1 on Solaris 10 - ORacle 9.2.0.7?Is the problem about SAP profile parameters or Solaris Kernel parameters
Best regards,Also dev_disp is like below:
sid KZP
systemid 370 (Solaris on SPARCV9 CPU)
relno 6400
patchlevel 0
patchno 221
intno 20020600
make: single threaded, Unicode, 64 bit
pid 22016
***LOG Q00=> DpSapEnvInit, DPStart (00 22016) [dpxxdisp.c 1104]
shared lib "dw_xml.so" version 221 successfully loaded
shared lib "dw_xtc.so" version 221 successfully loaded
shared lib "dw_stl.so" version 221 successfully loaded
shared lib "dw_gui.so" version 221 successfully loaded
shared lib "dw_mdm.so" version 221 successfully loaded
MtxInit: -2 0 0
DpSysAdmExtInit: ABAP is active
DpIPCInit2: start server >sapkzpn2_KZP_00 <
DpShMCreate: sizeof(wp_adm) 10752 (1344)
DpShMCreate: sizeof(tm_adm) 3728952 (18552)
DpShMCreate: sizeof(wp_ca_adm) 31200 (104)
DpShMCreate: sizeof(appc_ca_adm) 10400 (104)
DpShMCreate: sizeof(comm_adm) 316000 (632)
DpShMCreate: sizeof(vmc_adm) 0 (560)
DpShMCreate: sizeof(wall_adm) (40056/36728/88/192)
DpShMCreate: SHM_DP_ADM_KEY (addr: 0xffffffff70c00000, size: 4181592)
DpShMCreate: allocated sys_adm at 0xffffffff70c00000
DpShMCreate: allocated wp_adm at 0xffffffff70c01c88
DpShMCreate: allocated tm_adm_list at 0xffffffff70c04688
DpShMCreate: allocated tm_adm at 0xffffffff70c046b0
DpShMCreate: allocated wp_ca_adm at 0xffffffff70f92ce8
DpShMCreate: allocated appc_ca_adm at 0xffffffff70f9a6c8
DpShMCreate: allocated comm_adm_list at 0xffffffff70f9cf68
DpShMCreate: allocated comm_adm at 0xffffffff70f9cf80
DpShMCreate: allocated vmc_adm_list at 0xffffffff70fea1e0
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 0xffffffff70fea208
DpShMCreate: allocated wall_adm at 0xffffffff70fea210
MBUF state OFF
ThTaskStatus: rdisp/reset_online_during_debug 0
EmInit: MmSetImplementation( 2 ).
<ES> client 0 initializing ....
<ES> InitFreeList
<ES> block size is 4096 kByte.
Using implementation std
EsIUnamFileMapInit: ES base = 0x0xfffffffe60000000
EsStdInit: Extended Memory 4092 MB allocated
<ES> 1022 blocks reserved for free list.
ES initialized.
Fri Jan 29 15:11:07 2010
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 2.6.1 2.6 4.0) [dpxxdisp.c 1490]
***LOG Q0K=> DpMsAttach, mscon ( sapkzpn2) [dpxxdisp.c 10127]
DpStartStopMsg: send start message (myname is >sapkzpn2_KZP_00 <)
DpStartStopMsg: start msg sent
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
Fri Jan 29 15:11:08 2010
DpMsgAdmin: Set release to 6400, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c 1025]
DpMsgAdmin: Set patchno for this platform to 221
Release check o.K.
Fri Jan 29 15:11:29 2010
ERROR => W0 (pid 22021) died [dpxxdisp.c 12698]
ERROR => W2 (pid 22023) died [dpxxdisp.c 12698]
my types changed after wp death/restart 0xbf --> 0xbd
ERROR => W3 (pid 22024) died [dpxxdisp.c 12698]
my types changed after wp death/restart 0xbd --> 0xb9
ERROR => W4 (pid 22025) died [dpxxdisp.c 12698]
ERROR => W5 (pid 22028) died [dpxxdisp.c 12698]
my types changed after wp death/restart 0xb9 --> 0xb1
ERROR => W6 (pid 22030) died [dpxxdisp.c 12698]
my types changed after wp death/restart 0xb1 --> 0xa1
ERROR => W7 (pid 22038) died [dpxxdisp.c 12698]
my types changed after wp death/restart 0xa1 --> 0x81
Fri Jan 29 15:12:08 2010
ERROR => W1 (pid 22022) died [dpxxdisp.c 12698]
my types changed after wp death/restart 0x81 --> 0x80
DP_FATAL_ERROR => DpWPCheck: no more work processes
DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
killing W0-22021 (SIGUSR2)
ERROR => DpWpKill(22021, SIGUSR2) failed [dpxxtool.c 2508]
killing W1-22022 (SIGUSR2)
ERROR => DpWpKill(22022, SIGUSR2) failed [dpxxtool.c 2508]
killing W2-22023 (SIGUSR2)
ERROR => DpWpKill(22023, SIGUSR2) failed [dpxxtool.c 2508]
killing W3-22024 (SIGUSR2)
killing W7-22038 (SIGUSR2)
ERROR => DpWpKill(22038, SIGUSR2) failed [dpxxtool.c 2508]
NiWait: sleep (10000 msecs) ...
NiISelect: timeout 10000 ms
NiISelect: maximum fd=15
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Jan 29 15:12:18 2010
NiISelect: TIMEOUT occured (10000 ms)
dump system status
Workprocess Table (long) Fri Jan 29 09:12:18 2010
========================
No Ty. Pid Status Cause Start Err Sem CPU Time Program Cl User Action Table
0 DIA 22021 Ended no 1 0 78 SAPSYS
1 DIA 22022 Ended no 1 0 78 SAPSYS
2 UPD 22023 Ended no 1 0 78 SAPSYS
3 ENQ 22024 Ended no 1 0 78 SAPSYS
4 BTC 22025 Ended no 1 0 78 SAPSYS
5 BTC 22028 Ended no 1 0 78 SAPSYS
6 SPO 22030 Ended no 1 0 71 SAPSYS
7 UP2 22038 Ended no 1 0 71 SAPSYS
Dispatcher Queue Statistics Fri Jan 29 09:12:18 2010
===========================
--------++++--
+
Typ
now
high
max
writes
reads
--------++++--
+
NOWP
0
3
2000
10
10
--------++++--
+
DIA
5
5
2000
5
0
--------++++--
+
UPD
0
0
2000
0
0
--------++++--
+
ENQ
0
0
2000
0
0
--------++++--
+
BTC
0
0
2000
0
0
--------++++--
+
SPO
0
0
2000
0
0
--------++++--
+
UP2
0
0
2000
0
0
--------++++--
+
max_rq_id 13
wake_evt_udp_now 0
wake events total 9, udp 6 ( 66%), shm 3 ( 33%)
since last update total 9, udp 6 ( 66%), shm 3 ( 33%)
Dump of tm_adm structure: Fri Jan 29 09:12:18 2010
=========================
Term uid man user term lastop mod wp ta a/i (modes)
Workprocess Comm. Area Blocks Fri Jan 29 09:12:18 2010
=============================
Slots: 300, Used: 1, Max: 0
--------++--
+
id
owner
pid
eyecatcher
--------++--
+
0
DISPATCHER
-1
WPCAAD000
NiWait: sleep (5000 msecs) ...
NiISelect: timeout 5000 ms
NiISelect: maximum fd=15
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Jan 29 15:12:23 2010
NiISelect: TIMEOUT occured (5000 ms)
DpHalt: shutdown server >sapkzpn2_KZP_00 < (normal)
DpJ2eeDisableRestart
DpModState: buffer in state MBUF_PREPARED
NiBufSend starting
NiIWrite: write 110, 1 packs, MESG_IO, hdl 3, data complete
MsINiWrite: sent 110 bytes
MsIModState: change state to SHUTDOWN
DpModState: change server state from STARTING to SHUTDOWN
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmKeySharedMMU( 57 ) = 0 (octal)
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmKeySharedMMU( 57 ) = 0 (octal)
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes...
Stop gateway
killing proc (22019) (SOFT_KILL)
Stop icman
killing proc (22020) (SOFT_KILL)
Terminate gui connections
kill(22019,0) successful -> process alive
waiting for termination of gateway
NiWait: sleep (1000 msecs) ...
NiISelect: timeout 1000 ms
NiISelect: maximum fd=15
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Fri Jan 29 15:12:24 2010
NiISelect: TIMEOUT occured (1000 ms)
kill(22019,0) -> ESRCH: process died
kill(22020,0) -> ESRCH: process died
DpHalt: cancel all lcom connections
MPI CancelAll 2 -> 0
MPI DeleteAll 2 -> 0
DpStartStopMsg: send stop message (myname is >sapkzpn2_KZP_00 <)
NiIMyHostName: hostname = 'sapkzpn2'
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 163 bytes
NiBufSend starting
NiIWrite: write 562, 1 packs, MESG_IO, hdl 3, data complete
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name -, type 4, key -
DpStartStopMsg: stop msg sent
NiIRead: read 229, 1 packs, MESG_IO, hdl 3, data complete
NiBufIn: NIBUF len=229
NiBufIn: Packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 229 bytes
MSG received, len 110+119, flag 1, from MSG_SERVER, typ 0, key -
DpHalt: received 119 bytes from message server
NiIRead: read 229, 1 packs, MESG_IO, hdl 3, data complete
NiBufIn: NIBUF len=229
NiBufIn: Packet complete for hdl 3
NiBufReceive starting
MsINiRead: received 229 bytes
MSG received, len 110+119, flag 1, from MSG_SERVER, typ 0, key -
DpHalt: received 119 bytes from message server
DpHalt: no more messages from the message server
DpHalt: send keepalive to synchronize with the message server
cleanup event management
cleanup shared memory/semaphores
ShmCleanup SHM_SYS_ADM_KEY
ShmCleanup( 1 )
ShmCreate( 1, 0, 2, 0x0xffffffff7fffeab8 )
ShmProtect( 1, 3 )
ShmKeySharedMMU( 1 ) = 0 (octal)
ShmCreate( 1, 0, 2, -> 0x0xffffffff7b100000 )
ShmCleanup SHM_DP_ADM_KEY
ShmCleanup( 2 )
ShmCreate( 2, 0, 2, 0x0xffffffff7fffeab8 )
ShmProtect( 2, 3 )
ShmKeySharedMMU( 2 ) = 0 (octal)
ShmCreate( 2, 0, 2, -> 0x0xffffffff70c00000 )
ShmCleanup SHM_DP_CA_KEY
ShmCleanup( 3 )
ShmCreate( 3, 0, 2, 0x0xffffffff7fffeab8 )
ShmProtect( 3, 3 )
ShmKeySharedMMU( 3 ) = 0 (octal)
ShmCreate( 3, 0, 2, -> 0x0xffffffff6fc00000 )
ShmCleanup SHM_PF_KEY
ShmCleanup( 4 )
ShmCreate( 4, 0, 2, 0x0xffffffff7fffeab8 )
ShmKeyPermission( 4 ) = 0740 (octal)
ShmKeySharedMMU( 4 ) = 0 (octal)
ShmProtect( 4, 3 )
ShmKeySharedMMU( 4 ) = 0 (octal)
ShmCreate( 4, 0, 2, -> 0x0xffffffff71f00000 )
ShmCleanup SHM_PRES_BUF
ShmCleanup( 14 )
ShmCreate( 14, 0, 2, 0x0xffffffff7fffeab8 )
ShmGet( 10, 14, 0, 2, 0x0xffffffff7fffe970 )
ShmGet( 10, 14, 0, 2, -> 0x0xffffffff7597a000 )
ShmProtect( 14, 3 )
ShmProtect: Key=14 not attached
ShmProtect( 14, 3 )
ShmCreate( 14, 0, 2, -> 0x0xffffffff7597a000 )
ShmCleanup SHM_CALI_BUFFER
ShmCleanup( 11 )
ShmCreate( 11, 0, 2, 0x0xffffffff7fffeab8 )
ShmGet( 10, 11, 0, 2, 0x0xffffffff7fffe970 )
ShmGet( 10, 11, 0, 2, -> 0x0xffffffff76040000 )
ShmProtect( 11, 3 )
ShmProtect: Key=11 not attached
ShmProtect( 11, 3 )
ShmCreate( 11, 0, 2, -> 0x0xffffffff76040000 )
ShmCleanup SHM_DB_TBUFF
ShmCleanup( 19 )
ShmCreate( 19, 0, 2, 0x0xffffffff7fffeab8 )
ShmKeyPermission( 19 ) = 0740 (octal)
ShmKeySharedMMU( 19 ) = 0 (octal)
ShmProtect( 19, 3 )
ShmKeySharedMMU( 19 ) = 0 (octal)
ShmCreate( 19, 0, 2, -> 0x0xffffffff66000000 )
ShmCleanup SHM_DB_TBUFF_P
ShmCleanup( 33 )
ShmCreate( 33, 0, 2, 0x0xffffffff7fffeab8 )
ShmKeyPermission( 33 ) = 0740 (octal)
ShmKeySharedMMU( 33 ) = 0 (octal)
ShmProtect( 33, 3 )
ShmKeySharedMMU( 33 ) = 0 (octal)
ShmCreate( 33, 0, 2, -> 0x0xffffffff70400000 )
ShmCleanup SHM_DB_STBUFF
ShmCleanup( 41 )
ShmCreate( 41, 0, 2, 0x0xffffffff7fffeab8 )
ShmKeyPermission( 41 ) = 0740 (octal)
ShmKeySharedMMU( 41 ) = 0 (octal)
ShmProtect( 41, 3 )
ShmKeySharedMMU( 41 ) = 0 (octal)
ShmCreate( 41, 0, 2, -> 0x0xffffffff66800000 )
ShmCleanup SHM_DB_TTBUFF
ShmCleanup( 42 )
ShmCreate( 42, 0, 2, 0x0xffffffff7fffeab8 )
ShmGet( 40, 42, 0, 2, 0x0xffffffff7fffe970 )
ShmCreate( 40, 0, 2, 0x0xffffffff7fffe798 )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmKeySharedMMU( 40 ) = 0 (octal)
ShmProtect( 40, 3 )
ShmCreate( 40, 0, 2, -> 0x0xffffffff60000000 )
ShmGet( 40, 42, 0, 2, -> 0x0xffffffff62972000 )
ShmProtect( 42, 3 )
ShmProtect: Key=42 not attached
ShmProtect( 42, 3 )
ShmCreate( 42, 0, 2, -> 0x0xffffffff62972000 )
ShmDelete( 40 )
ShmCleanup SHM_DB_FTBUFF
ShmCleanup( 43 )
ShmCreate( 43, 0, 2, 0x0xffffffff7fffeab8 )
ShmGet( 40, 43, 0, 2, 0x0xffffffff7fffe970 )
ShmCreate( 40, 0, 2, 0x0xffffffff7fffe798 )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_SNTBUFF
ShmCleanup( 45 )
ShmCreate( 45, 0, 2, 0x0xffffffff7fffeab8 )
ShmGet( 40, 45, 0, 2, 0x0xffffffff7fffe970 )
ShmCreate( 40, 0, 2, 0x0xffffffff7fffe798 )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_IRBUFF
ShmCleanup( 44 )
ShmCreate( 44, 0, 2, 0x0xffffffff7fffeab8 )
ShmGet( 40, 44, 0, 2, 0x0xffffffff7fffe970 )
ShmCreate( 40, 0, 2, 0x0xffffffff7fffe798 )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_OBJ_BUFFER
ShmKeySharedMMU( 31 ) = 0 (octal)
ShmCreate( 31, 0, 2, -> 0x0xffffffff6f400000 )
closing connect handles (dgm + tcp)
DpDelSocketInfo: del info for socket 1 (type=2)
NiICloseHandle: shutdown and close hdl 1 / socket 8
DpDelSocketInfo: del info for socket 2 (type=1)
NiBufClose: clear extensions for hdl 2
NiBufSetStat: bufstat of hdl 2 changed from OK to OFF
NiICloseHandle: shutdown and close hdl 2 / socket 9
***LOG Q05=> DpHalt, DPStop ( 22016) [dpxxdisp.c 9033]
shutdown completed - server stopped ***
Good Bye .....
Could you please help me about this issue?
Best regards -
Solaris 8 installation problem on Dell laptop
Hi
I have Dell Latitude CPx laptop which has windows now.
I have freed space from the disk and removed the freed partition from windows control using fdisk and tried installing Solaris 8, 7/01 release using interactive install.
After initial screens scanning devices, config building, prompts for language selection. As soon as I enter 0 for English, the screen prints junk charcters and beeps continuosly and hangs.
Do any of you have a clue, to get over this problem.
Also please let me know, how to disable PnP feature in BIOS, since I didn't find PnP in BIOS setup.
Thanks in advance for help.
RamThere seems to be a patch available at http://sunsolve.sun.com
Patch-ID # 112352-01
Hope it's what you were looking for. -
when i try to open a web page, a blue screen appears - message says - sarfari cannot open the page because it is not connected to the internet. i have an iphone - no proble and a laptop - no problem as well.
what is wrong?There are other things that need attention:
Your above posted system details show outdated plugin(s) with known security and stability risks that you should update.
*Shockwave Flash 10.0 r32
Update the [[Managing the Flash plugin|Flash]] plugin to the latest version.
*http://www.adobe.com/software/flash/about/ -
Persistent blue screen of death problems on Toshiba laptop pc; need help
hey, guys,
I was hoping you could help me out here. I have been experiencing persistent blue screen of death problems on my Toshiba laptop since December 21 of 2014. The first two times I started having theses persistent issues, I downloaded a bunch of redundant programs and games onto my computer, some of which were virus infected. I had these programs on my computer for a while before my laptop was taken in for repairs. I eventually uninstalled some unnecesssary programs from my pc, hoping it would have fixed these issues, even tried windows update. I didn't have a clue that my problems were due to virus infections/malware until the two most recent times my computer was taken in for repairs; I had always been thinking it was a defective driver. My laptop has already been in for repairs at least twice due to these perpetual BSOD problems; I had Norton Internet Security installed on my pc before the Geek Squad team (who repaired my computer and found 312 traces of malware in my system during the virus test; I was told by them that I had mistakenly downloaded infected web browsers onto my pc) switched me to Webroot SecureAnywhere (they said it was better at detecting viruses/malware than my NIS), but even after my pc has been through repairs twice in a row, I am still experiencing blue screens (this only seems to have happened once each week, and on one occasion, I went through almost two weeks without it occurring). I am pretty sure, that I haven't downloaded anything onto my computer infected with viruses/malware (each of the scans done by my Webroot antivirus have found nothing), I have only a few games/apps installed on my pc, and what I downloaded all came from Microsoft's official website. I can't afford to be wasting any more money on repairs, and I am desperately searching for any possible way to fix this myself. Any help would be appreciated. I have a copy of two of the memory dumps from my most recent crashes (I also have the dump reports from my most recent crashes dating back to March 6; I got these from an app from NirSort called Blue Screen View, if you need those) I also have my system specs:
http://1drv.ms/1I6AsaE
http://1drv.ms/1Qdsb7T
Note that many of these earler dump reports (the ones from March) came from viruses. The ones from most recently as last month, I am not sure about.
Attachments:
POPCHOCK-PC.txt 149 KBSatellite C75D-B7300 (PSCLEU-009004)
Thrashing about this way gets us nowhere.
Best to restore the hard disk to its original out-of-the-box contents.
Settings > Change PC settings > Update and recovery tab > Recovery tab > Remove everything and reinstall Windows
Use the freshly restored machine for a day or so before any installations of hardware, software, or updates of any kind. If you get no crashes, the problem is not likely due to hardware.
Then add updates and other things slowly, keeping track of them. If you get crashes after that, give us the corresponding dmp files.
-Jerry
Maybe you are looking for
-
Problem with Simple Transformation
Hi to all I am working with ST, and have the following issue: I have a highly nested xml structure, and, when I execute a abap program with a myself ST, only the last one data is passed to internal tables. I want to know: how can I do to get that all
-
I am working on a line chart and want to add a legend to it. For the purpose I am using <mx:Legend dataProvider="{bigChart}"/> Now the y-axis in the chart can display different properties based on the items clicked before rendering. It can be profitA
-
I have just updated from ios 6.0.1 to 6.1 hoping apple have been listening to people, but no. STILL says "incorrect password" so cannot connect to Wi-fi, only connects when i disable the password, but that is unacceptable, SORT THIS OUT APPLE !!!!!!!
-
Schedule report to Inbox. No destinations available.
A user is trying to schedule a report to go to another user's Business Objects inbox. When they go to Destinations the list of available users is blank. When I try this as an Administrator there is a full listing of Users. Is there a way to get this
-
I have icloud. I have backed up my photos from my iPhone 5 to my iPad. Can I now delete the photos from my phone and they will stay on my iPad? I need to clear space in order to run an update.