SAP Content server hp unix apache issue

Once we completed the DMS installation on HP Unix ( HP 11.23) we found
that the apache server is not running and gaved the following error
while trying to start that.
$ apachectl -v
Server version: Apache/2.0.52
Server built: Mar 26 2011 15:20:39
$ apachectl start
Syntax error on line 233 of /home/sapcsc/conf/httpd.conf:
Cannot load /home/sapcsc/modules/mod_sapcsc2.so into server: Invalid
argument
We followed the note 664384 and exported the following enviorement
variable in the system. We logged into the system with user sapcs and
executed these commands.
export LDFLAGS="+DD64 +DSitanium2"
export CFLAGS="+DD64 +DSitanium2"
After that we again configured the apache with following command.
configure u2013prefix=/usr/users/sapcsc --enable-mods-shared=most u2013with-
mpm=prefork
Now, when we are trying to compile the apache by executing the make
command we are getting following error.
ld: Mismatched Data ABI. Expected EF_IA_64_ABI64 but found None in file
xmltok.lo
Fatal error
Please advice are we missing any steps .
Regards

Hi Markus , 
                     Few things I noticed
1. The apache was installed as per the three steps mentioned in the guide and note 664384 , however we did not exported the environment variable for 64 bit. when we tried to run the apache after the DMS installation it gave this error .
$ apachectl start
Syntax error on line 233 of /home/sapcsc/conf/httpd.conf:
Cannot load /home/sapcsc/modules/mod_sapcsc2.so into server: Invalid
argument
2. Now when we tried to install it using the 64 bit after exporting the environment variable it gave Mismatched Data ABI error , now even when we have unset the enviorement variable it is not getting installed and giving same Mismatched Data ABI error.
Here is the required information.
$ file mod_sapcsc2.so
mod_sapcsc2.so: ELF-64 shared object file - IA64
$ chatr mod_sapcsc2.so
mod_sapcsc2.so:
         64-bit ELF shared library
         shared library dynamic path search:
             LD_LIBRARY_PATH    enabled  first
             SHLIB_PATH         enabled  second
             embedded path      enabled  third  /opt/aCC/lib:/usr/lib/hpux64:/opt/langtools/lib/hpux64
         shared library list:
             libCsup.so.1
             libm.so.1
             libcl.so.1
             libpthread.so.1
             libdl.so.1
             libnsl.so.1
         shared library mapped private disabled
         shared vtable support disabled
         explicit unloading enabled
         linkage table protection disabled
         segments:
             index type     address      flags size
                 6 text 4000000000000000 z---c-    D (default)
                 7 data 6000000000000000 -m    D (default)
         kernel assisted branch prediction enabled
         lazy swap allocation for dynamic segments disabled
         nulptr dereferences trap disabled
         address space model: default
         caliper dynamic instrumentation disabled
GPILDMS:/>>cc -V
(Bundled) cc: HP C/aC++ B3910B A.06.12 [Oct 11 2006]
GPILDMS:/>>aCC -V
ksh: aCC:  not found
Regards
Edited by: Singh Dharm on Mar 30, 2011 8:29 AM

Similar Messages

  • SAP Content server installation using apache web server under HP-UX 11i

    Hello,
    I installed a SAP Content Server 6.4 in HP-UX 11.11 with MaxDB 7.6.
    Although Installation is finished completely I got an syxtext error when apache web server is started after completing installation as below;
    kbwpdc 106: /home/dmscs/bin>./apachectl start
    Syntax error on line 233 of /home/dmscs/conf/httpd.conf:
    Cannot load /home/dmscs/modules/mod_sapcs2.so into server: Invalid
    argument
    I think apache web server doesn't know mod_sapcs2.so although it exists in the directory(/home/dmscs/module).
    - Working sequence
    1) Environment variables setup to compile with 64bit.
    2) "configure" generation with option relevant to SAP content server
    3) "make" generation
    4) "make install" generation
    5) Install SAP Content server 6.40
    6) Install MaxDB 7.6
    7) Edit httpd.conf for loading mod_sapcs2.so module and changing Listen port.
    8) Start apache web server.
    Do I need to configure to solve this syntext error? missing any step?
    Please let me know to solution if you had experienced with the same problem.
    I will wait for your response.
    Thanks,
    Mark Yoo.

    Hi Mark,
    Can i check with you how do you set your environment to compile in 64bit ? My file mod_sapcs.o apear in the libexec directory instead of mod_sapcs.so. That why my apache cannot start. It prompted Cannot load module /home/sapcs/libexec/mod_sapc.o
    Regards
    Kim

  • SAP Content Server Size Limitations

    Hi,
    Has SAP Content Server any limitations regarding the amount of information to be stored ?.
    We have a 160 Gb/ year data to be stored and we doubt to use the SAP content Server or some other content server ( IXOS, Documetum ... ).
    Best Regards,
    Francisco.

    Hi,
    I don't think there would be any sizing restrictions:
    I found some SAP Notes at this link:
    http://help.sap.com/saphelp_47x200/helpdata/en/40/4695331ea6424b942a953616f01b9e/frameset.htm
    Where there are a list of notes which 'might' be useful..
    You might want to check this note if you are using UNIX:
    Note 586895 - SAP Content Server for UNIX (composite SAP note)
    Regards,
    Siddhesh

  • Error while starting Apache WebServer in SAP Content server from sapcs user

    Dear Consultants,
    We are facing a Issue while staring Apache Server from SAPCS user
    We have installed SAP Content server 6.4 with SAP MAX DB 7.6 on RHEL
    Linux 64 bit OS, we also installed Apache web server server following SAP
    Standard Installation guide,
    When We run Apache server using sapcs user we are facing a error
    Error (1) -
    [sapcs@hpsebdev1 bin]$ apachectl start
    (13)Permission denied: make_sock: could not bind to address [::]:80
    (13)Permission denied: make_sock: could not bind to address 0.0.0.0:80
    no listening sockets available, shutting down
    Unable to open logs
    Error (2) - same issue we get when we use httpd script to start apache
    service.
    [sapcs@hpsebdev1 bin]$ httpd -k start
    (13)Permission denied: make_sock: could not bind to address [::]:80
    (13)Permission denied: make_sock: could not bind to address 0.0.0.0:80
    no listening sockets available, shutting down
    Unable to open logs
    Please Help regarding the issue
    Regards
    Gagan Sharma
    SAP BASIS Consultant

    Hello Gaghan,
    From the error it seems that port 80 is being already used. Did you install the second Apache under a different user?
    Can you please try using another port?
    Regards,
    Blanca

  • How to install Apache Web server on my SAP Content Server

    Dear Experts,
    I am in the process of installaing Content Server in my landscape, i am working on Suse Linux 10 SP2 and planning to install ContentServer 6.30.
    I have read the standard SAP installation document for the same and it says that we need to install Apache Web server version 1.3.XX, so i have downloaded the file apache_1.3.27-x86_64-whatever-linux22.tar.
    Now i want to know the following before i take any actions on my further installation of the Content Server
    What is the difference between Apache and httpd servers (services) are they different or same
    Is the file apache_1.3.27-x86_64-whatever-linux22.tar correct to install Web Server on my Linux system
    Do i have to download any other httpd files
    How to install and start the Web server on my Linux
    Waiting for some information
    Thanks and regards
    BasoKing

    You can install a higher apache also (2.2.x), I'd not use the old versions. I'd also not use a "somwhere" compiled apache, you don't now if that version is clean.
    I'd rather compile an own one, it's not that difficult:
    Note 664384 - Generation info for Apache Web server for SAP Content Server
    The result will be a default webserver (httpd) without any unnecessary modules compiled in.
    Markus

  • Apache start error on SAP Content server 6.40

    Hi all
    I installed a SAP Content Server 6.4 successfully in Solaris 10 with MaxDB 7.6.
    Although Installation is finished completely I got an syxtext error when apache web server is started after completing installation as below;
    dmscs/bin>./apachectl start
    Cannot load /usr/sap/XXD/apache/libexec/mod_sapcs.so into server: ld.so.1: httpd: fatal:sap/Apache/libexec/mod_sapcs.so: wrong ELF class: ELFCLASS64
    ./apachectl start: httpd could not be started
    let me know to solution if you had experienced with the same problem.

    Hi Nelis,
    We did the module registration after after installation, Please find the below of httpd.conf.
    =======================================================================================
    Example:
    LoadModule foo_module libexec/mod_foo.so
    LoadModule sapcs_module libexec/mod_sapcs.so
    LoadModule vhost_alias_module libexec/mod_vhost_alias.so
    LoadModule env_module         libexec/mod_env.so
    LoadModule config_log_module  libexec/mod_log_config.so
    LoadModule mime_magic_module  libexec/mod_mime_magic.so
    LoadModule mime_module        libexec/mod_mime.so
    LoadModule negotiation_module libexec/mod_negotiation.so
    LoadModule status_module      libexec/mod_status.so
    LoadModule info_module        libexec/mod_info.so
    LoadModule includes_module    libexec/mod_include.so
    LoadModule autoindex_module   libexec/mod_autoindex.so
    LoadModule dir_module         libexec/mod_dir.so
    LoadModule cgi_module         libexec/mod_cgi.so
    LoadModule asis_module        libexec/mod_asis.so
    LoadModule imap_module        libexec/mod_imap.so
    LoadModule action_module      libexec/mod_actions.so
    LoadModule speling_module     libexec/mod_speling.so
    LoadModule userdir_module     libexec/mod_userdir.so
    LoadModule alias_module       libexec/mod_alias.so
    LoadModule rewrite_module     libexec/mod_rewrite.so
    LoadModule access_module      libexec/mod_access.so
    LoadModule auth_module        libexec/mod_auth.so
    LoadModule anon_auth_module   libexec/mod_auth_anon.so
    LoadModule dbm_auth_module    libexec/mod_auth_dbm.so
    LoadModule digest_module      libexec/mod_digest.so
    LoadModule proxy_module       libexec/libproxy.so
    LoadModule cern_meta_module   libexec/mod_cern_meta.so
    LoadModule expires_module     libexec/mod_expires.so
    LoadModule headers_module     libexec/mod_headers.so
    LoadModule usertrack_module   libexec/mod_usertrack.so
    LoadModule log_forensic_module libexec/mod_log_forensic.so
    LoadModule unique_id_module   libexec/mod_unique_id.so
    LoadModule setenvif_module    libexec/mod_setenvif.so
    Reconstruction of the complete module list from all available modules
    (static and shared ones) to achieve correct module execution order.
    [WHENEVER YOU CHANGE THE LOADMODULE SECTION ABOVE UPDATE THIS, TOO]
    ClearModuleList
    AddModule mod_sapcs.cpp
    AddModule mod_vhost_alias.c
    AddModule mod_env.c
    AddModule mod_log_config.c
    AddModule mod_mime_magic.c
    AddModule mod_mime.c
    AddModule mod_negotiation.c
    AddModule mod_status.c
    AddModule mod_info.c
    AddModule mod_include.c
    AddModule mod_autoindex.c
    AddModule mod_dir.c
    AddModule mod_cgi.c
    AddModule mod_asis.c
    AddModule mod_imap.c
    AddModule mod_actions.c
    AddModule mod_speling.c
    AddModule mod_userdir.c
    AddModule mod_alias.c
    AddModule mod_rewrite.c
    AddModule mod_access.c
    AddModule mod_auth.c
    AddModule mod_auth_anon.c
    AddModule mod_auth_dbm.c
    AddModule mod_digest.c
    AddModule mod_proxy.c
    AddModule mod_cern_meta.c
    AddModule mod_expires.c
    AddModule mod_headers.c
    AddModule mod_usertrack.c
    AddModule mod_log_forensic.c
    AddModule mod_unique_id.c
    AddModule mod_so.c
    AddModule mod_setenvif.c
    Can you guide me where exactly point to the correct location for /ContentServer/ContentServer.dll in httpd.conf.
    =========================================================================
    #<VirtualHost *:80>
       DocumentRoot /www/docs/dummy-host.example.com
       ServerName dummy-host.example.com
       ErrorLog logs/dummy-host.example.com-error_log
       CustomLog logs/dummy-host.example.com-access_log common
    #</VirtualHost>
    <IfModule mod_sapcs.cpp>
      AddModuleInfo ContentServer "SAP Content Server 640/0 (Prototype) (C) SAP AG 1998, 2001"
      CSConfigPath /export/home/sapcs1/conf/cs.conf
      <Location /sapcs>
      SetHandler sapcs_module
      Allow from all
      </Location>
      <Location /ContentServer/ContentServer.dll>
      SetHandler sapcs_module
      Allow from all
      </Location>
      <Location /contentserver/contentserver.dll>
      SetHandler sapcs_module
      Allow from all
      </Location>
    Regards,
    Panu
    Edited by: kumar panu on Sep 7, 2010 9:05 AM
    Edited by: kumar panu on Sep 7, 2010 9:07 AM
    Edited by: kumar panu on Sep 7, 2010 9:08 AM
    Edited by: kumar panu on Sep 7, 2010 9:08 AM

  • Monitoring Web Dispatcher, SAP Content Server, apache with SM 7.1

    Hello,
    Did anyone of you come across monitoring possibilities of  SAP WD, Content Server or an apache via SM 7.1 SP04? I want to integrate monitoring of these components to technical monitoring in new SM, but didn't find much about it so far.
    Thank you very much for help.

    Caro Mauro,
    I'm more or less in the same situation right now.
    Taking into account that you ask for help on this subject last 2004 Oct. I suppose that you have probably solved the problem.
    Please can you help me with the solution implemented.
    Find below my current work e-mail adress
    [email protected]
    Thanks in advance,
    Best regards, Xavier Grau.

  • Issue after installa SAP Content Server

    Dear friends,
    I have installed a SAP Contenet Server and Cache server on a windows 2003 server with maxdb, SAP NW 7.0 SR3
    Installation using sapinst finished sucessfully, I checked the url link to test see the status of content server and this owrks fine:
    http://hostname:1090/ContentServer/ContentServer.dll?serverInfo
    But in the url link of cache server shows page not found:
    http://hostname:1095/Cache/CSProxyCache.dll?serverInfo
    I restarted SAp content server an cache server and issue persist, any idea to solve this issue?
    Thanks friends!!!

    Hi Kalyan,
    First thanks for your answers.
    1) Folders exist
    2) I can´t find the port 1095 is used in "services" file but I changed  the port to 1094 in the IIS and it didn't work.
    3)cache website is up, also I restarted the IIS  and websites.
    Issue persiste only for cache sever this message appears:
    The page cannot be displayed
    The page you are looking for is currently unavailable. The Web site might be experiencing technical difficulties, or you may need to adjust your browser settings.
    For content server show status runing.
    Please your help, thanks.
    Edited by: Friend on Jan 13, 2009 4:30 PM

  • SAP Content Server

    Dear Experts,
    I got problem in installing SAP Content Server 6.30 in Solaris 9 (Unix-SPARC 64bit). After discus with OSS they sugest to review the Apache installation, i try to follow the OSS note number 664384, but i confused with some error about the compilation, here is my compilation step :
    1. We install gcc for solaris 9 from www.sunfreeware.com
    2. In PATH we add PATH=/usr/bin:/opt/sfw/gcc-3/bin
    3. run configure --prefix=/home/sapcs --enable-module=most --enable-shared=max
        i got error :
    ============================================================
        ./helpers/TestCompile: make: not found
    ++ doing sanity check on compiler and options+
    ** A test compilation with your Makefile configuration
    ** failed.  The below error output from the compilation
    ** test will give you an idea what is failing. Note that
    ** Apache requires an ANSI C Compiler, such as gcc.
    ======== Error Output for sanity check ========
    ./helpers/TestCompile: make: not found
    ============= End of Error Report =============
    4. Then we add PATH=/usr/bin:/usr/ccs/bin:/opt/sfw/gcc-3/bin and CFLAGS="-xarch=v9" (note 664384)
    ================================================
    re run ./configure --prefix=/home/sapcs/ --enable-module=most --enable-shared=max
    Configuring for Apache, Version 1.3.41
    ++ using installation path layout: Apache (config.layout)+
    Creating Makefile
    Creating Configuration.apaci in src
    ++ enabling mod_so for DSO support+
    Creating Makefile in src
    ++ configured for Solaris 290 platform+
    ++ setting C compiler to gcc+
    ++ setting C pre-processor to gcc -E+
    ++ using "tr [a-z] [A-Z]" to uppercase+
    ++ checking for system header files+
    ++ adding selected modules+
        o rewrite_module uses ConfigStart/End
          disabling DBM support for mod_rewrite
          (perhaps you need to add -ldbm, -lndbm or -lgdbm to EXTRA_LIBS)
        o dbm_auth_module uses ConfigStart/End
    ++ using builtin Expat+
    ++ checking sizeof various data types+
    ++ doing sanity check on compiler and options+
    ** A test compilation with your Makefile configuration
    ** failed.  The below error output from the compilation
    ** test will give you an idea what is failing. Note that
    ** Apache requires an ANSI C Compiler, such as gcc.
    ======== Error Output for sanity check ========
    cd ..; gcc  -DSOLARIS2=290 -DNO_DBM_REWRITEMAP -DUSE_EXPAT -I./lib/expat-lite -xarch=v9 `./apaci`     -o helpers/dummy helpers/dummy.c   -lsocket -lnsl -lpthread
    gcc: language arch=v9 not recognized
    ld: fatal: file helpers/dummy.c: unknown file type
    ld: fatal: File processing errors. No output written to helpers/dummy
    collect2: ld returned 1 exit status
    *** Error code 1
    make: Fatal error: Command failed for target `dummy'
    ============= End of Error Report =============
    Aborting!
    5.  I tried to remove the env variable CFLAGS="-xarch=v9", and the result it successfuly installed then i tried to install SAP Content Server 6.30, the installation had been done suceesfully but when i tried to start apache, it can not load the mod_sapcs.so
    Syntax error on line 205 of /home_sapcs/conf/httpd.conf:
    Cannot load /home_sapcs/libexec/mod_sapcs.so into server: ld.so.1: httpd: fatal: /home_sapcs/libexec/mod_sapcs.so: wrong ELF class: ELFCLASS64
    apachectl start: httpd could not be started
    Do you have any idea with this problem? I really need advice for this.
    Thanks in advance
    Bagus

    Hello Experts,
    Please provide the solution, how the problem was resolved. Even I am getting following error right after installation of Content server when installation prompts to restart the server, when I try to stop apache on Solaris 10, it throws following error:
    Syntax error on line 233 of /usr/local/apache2/conf/httpd.conf:
    Cannot load /usr/local/apache2/modules/mod_sapcs2.so into server: ld.so.1: httpd: fatal: /usr/local/apache2/modules/mod_sapcs2.so: wrong ELF class: ELFCLASS64
    I am facing this issue since very long now.
    Please reply at earliest.
    Thanks.
    Regards,
    Kashyap Shah

  • SAP Content Server error

    Hello colleagues,
    I have this error when start the Content Server,
    host:(/directory/apache/bin)(root)#./apachectl start
    httpd: Syntax error on line 66 of /directory/apache/conf/httpd.conf: Cannot load modules/mod_sapcs22.so into
    server: /directory/apache/modules/mod_sapcs22.so: undefined symbol: ap_log_error
    Can you help me?
    Thanks

    Hi Reagan,
    Execute the first parameter,
    rgqaserp:(/sapcontreps/apache/modules)(root)#cat /sapcontreps/apache/conf/httpd.conf
    # This is the main Apache HTTP server configuration file.  It contains the
    # configuration directives that give the server its instructions.
    # See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
    # In particular, see
    # <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
    # for a discussion of each configuration directive.
    # Do NOT simply read the instructions in here without understanding
    # what they do.  They're here only as hints or reminders.  If you are unsure
    # consult the online docs. You have been warned.
    # Configuration and logfile names: If the filenames you specify for many
    # of the server's control files begin with "/" (or "drive:/" for Win32), the
    # server will use that explicit path.  If the filenames do *not* begin
    # with "/", the value of ServerRoot is prepended -- so "logs/access_log"
    # with ServerRoot set to "/usr/local/apache2" will be interpreted by the
    # server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
    # will be interpreted as '/logs/access_log'.
    # ServerRoot: The top of the directory tree under which the server's
    # configuration, error, and log files are kept.
    # Do not add a slash at the end of the directory path.  If you point
    # ServerRoot at a non-local disk, be sure to specify a local disk on the
    # Mutex directive, if file-based mutexes are used.  If you wish to share the
    # same ServerRoot for multiple httpd daemons, you will need to change at
    # least PidFile.
    ServerRoot "/sapcontreps/apache"
    # Mutex: Allows you to set the mutex mechanism and mutex file directory
    # for individual mutexes, or change the global defaults
    # Uncomment and change the directory if mutexes are file-based and the default
    # mutex file directory is not on a local disk or is not appropriate for some
    # other reason.
    # Mutex default:logs
    # Listen: Allows you to bind Apache to specific IP addresses and/or
    # ports, instead of the default. See also the <VirtualHost>
    # directive.
    # Change this to Listen on specific IP addresses as shown below to
    # prevent Apache from glomming onto all bound IP addresses.
    #Listen 12.34.56.78:80
    Listen 1090
    # Dynamic Shared Object (DSO) Support
    # To be able to use the functionality of a module which was built as a DSO you
    # have to place corresponding `LoadModule' lines at this location so the
    # directives contained in it are actually available _before_ they are used.
    # Statically compiled modules (those listed by `httpd -l') do not need
    # to be loaded here.
    # Example:
    # LoadModule foo_module modules/mod_foo.so
    LoadModule sapcs_module modules/mod_sapcs22.so
    LoadModule authn_file_module modules/mod_authn_file.so
    #LoadModule authn_dbm_module modules/mod_authn_dbm.so
    #LoadModule authn_anon_module modules/mod_authn_anon.so
    #LoadModule authn_dbd_module modules/mod_authn_dbd.so
    #LoadModule authn_socache_module modules/mod_authn_socache.so
    LoadModule authn_core_module modules/mod_authn_core.so
    LoadModule authz_host_module modules/mod_authz_host.so
    LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
    LoadModule authz_user_module modules/mod_authz_user.so
    #LoadModule authz_dbm_module modules/mod_authz_dbm.so
    #LoadModule authz_owner_module modules/mod_authz_owner.so
    #LoadModule authz_dbd_module modules/mod_authz_dbd.so
    LoadModule authz_core_module modules/mod_authz_core.so
    LoadModule access_compat_module modules/mod_access_compat.so
    LoadModule auth_basic_module modules/mod_auth_basic.so
    #LoadModule auth_form_module modules/mod_auth_form.so
    #LoadModule auth_digest_module modules/mod_auth_digest.so
    #LoadModule allowmethods_module modules/mod_allowmethods.so
    #LoadModule file_cache_module modules/mod_file_cache.so
    #LoadModule cache_module modules/mod_cache.so
    #LoadModule cache_disk_module modules/mod_cache_disk.so
    #LoadModule cache_socache_module modules/mod_cache_socache.so
    #LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
    #LoadModule socache_dbm_module modules/mod_socache_dbm.so
    #LoadModule socache_memcache_module modules/mod_socache_memcache.so
    #LoadModule macro_module modules/mod_macro.so
    #LoadModule dbd_module modules/mod_dbd.so
    #LoadModule dumpio_module modules/mod_dumpio.so
    #LoadModule buffer_module modules/mod_buffer.so
    #LoadModule ratelimit_module modules/mod_ratelimit.so
    LoadModule reqtimeout_module modules/mod_reqtimeout.so
    #LoadModule ext_filter_module modules/mod_ext_filter.so
    #LoadModule request_module modules/mod_request.so
    #LoadModule include_module modules/mod_include.so
    LoadModule filter_module modules/mod_filter.so
    #LoadModule substitute_module modules/mod_substitute.so
    #LoadModule sed_module modules/mod_sed.so
    LoadModule mime_module modules/mod_mime.so
    LoadModule log_config_module modules/mod_log_config.so
    #LoadModule log_debug_module modules/mod_log_debug.so
    #LoadModule logio_module modules/mod_logio.so
    LoadModule env_module modules/mod_env.so
    #LoadModule expires_module modules/mod_expires.so
    LoadModule headers_module modules/mod_headers.so
    #LoadModule unique_id_module modules/mod_unique_id.so
    LoadModule setenvif_module modules/mod_setenvif.so
    LoadModule version_module modules/mod_version.so
    #LoadModule remoteip_module modules/mod_remoteip.so
    #LoadModule proxy_module modules/mod_proxy.so
    #LoadModule proxy_connect_module modules/mod_proxy_connect.so
    #LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
    #LoadModule proxy_http_module modules/mod_proxy_http.so
    #LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
    #LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
    #LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
    #LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
    #LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
    #LoadModule proxy_express_module modules/mod_proxy_express.so
    #LoadModule session_module modules/mod_session.so
    #LoadModule session_cookie_module modules/mod_session_cookie.so
    #LoadModule session_dbd_module modules/mod_session_dbd.so
    #LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
    #LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
    #LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
    #LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
    #LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
    LoadModule unixd_module modules/mod_unixd.so
    #LoadModule dav_module modules/mod_dav.so
    LoadModule status_module modules/mod_status.so
    LoadModule autoindex_module modules/mod_autoindex.so
    #LoadModule info_module modules/mod_info.so
    #LoadModule cgid_module modules/mod_cgid.so
    #LoadModule dav_fs_module modules/mod_dav_fs.so
    #LoadModule vhost_alias_module modules/mod_vhost_alias.so
    #LoadModule negotiation_module modules/mod_negotiation.so
    LoadModule dir_module modules/mod_dir.so
    #LoadModule actions_module modules/mod_actions.so
    #LoadModule speling_module modules/mod_speling.so
    #LoadModule userdir_module modules/mod_userdir.so
    LoadModule alias_module modules/mod_alias.so
    #LoadModule rewrite_module modules/mod_rewrite.so
    <IfModule unixd_module>
    # If you wish httpd to run as a different user or group, you must run
    # httpd as root initially and it will switch.
    # User/Group: The name (or #number) of the user/group to run httpd as.
    # It is usually good practice to create a dedicated user and group for
    # running httpd, as with most system services.
    User daemon
    Group daemon
    </IfModule>
    # 'Main' server configuration
    # The directives in this section set up the values used by the 'main'
    # server, which responds to any requests that aren't handled by a
    # <VirtualHost> definition.  These values also provide defaults for
    # any <VirtualHost> containers you may define later in the file.
    # All of these directives may appear inside <VirtualHost> containers,
    # in which case these default settings will be overridden for the
    # virtual host being defined.
    # ServerAdmin: Your address, where problems with the server should be
    # e-mailed.  This address appears on some server-generated pages, such
    # as error documents.  e.g. [email protected]
    ServerAdmin [email protected]
    # ServerName gives the name and port that the server uses to identify itself.
    # This can often be determined automatically, but we recommend you specify
    # it explicitly to prevent problems during startup.
    # If your host doesn't have a registered DNS name, enter its IP address here.
    #ServerName www.example.com:80
    # Deny access to the entirety of your server's filesystem. You must
    # explicitly permit access to web content directories in other
    # <Directory> blocks below.
    <Directory />
        AllowOverride none
        Require all denied
    </Directory>
    # Note that from this point forward you must specifically allow
    # particular features to be enabled - so if something's not working as
    # you might expect, make sure that you have specifically enabled it
    # below.
    # DocumentRoot: The directory out of which you will serve your
    # documents. By default, all requests are taken from this directory, but
    # symbolic links and aliases may be used to point to other locations.
    DocumentRoot "/sapcontreps/apache/htdocs"
    <Directory "/sapcontreps/apache/htdocs">
        # Possible values for the Options directive are "None", "All",
        # or any combination of:
        #   Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
        # Note that "MultiViews" must be named *explicitly* --- "Options All"
        # doesn't give it to you.
        # The Options directive is both complicated and important.  Please see
        # http://httpd.apache.org/docs/2.4/mod/core.html#options
        # for more information.
        Options Indexes FollowSymLinks
        # AllowOverride controls what directives may be placed in .htaccess files.
        # It can be "All", "None", or any combination of the keywords:
        #   AllowOverride FileInfo AuthConfig Limit
        AllowOverride None
        # Controls who can get stuff from this server.
        Require all granted
    </Directory>
    # DirectoryIndex: sets the file that Apache will serve if a directory
    # is requested.
    <IfModule dir_module>
        DirectoryIndex index.html
    </IfModule>
    # The following lines prevent .htaccess and .htpasswd files from being
    # viewed by Web clients.
    <Files ".ht*">
        Require all denied
    </Files>
    # ErrorLog: The location of the error log file.
    # If you do not specify an ErrorLog directive within a <VirtualHost>
    # container, error messages relating to that virtual host will be
    # logged here.  If you *do* define an error logfile for a <VirtualHost>
    # container, that host's errors will be logged there and not here.
    ErrorLog "logs/error_log"
    # LogLevel: Control the number of messages logged to the error_log.
    # Possible values include: debug, info, notice, warn, error, crit,
    # alert, emerg.
    LogLevel warn
    <IfModule log_config_module>
        # The following directives define some format nicknames for use with
        # a CustomLog directive (see below).
        LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
        LogFormat "%h %l %u %t \"%r\" %>s %b" common
        <IfModule logio_module>
          # You need to enable mod_logio.c to use %I and %O
          LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
        </IfModule>
        # The location and format of the access logfile (Common Logfile Format).
        # If you do not define any access logfiles within a <VirtualHost>
        # container, they will be logged here.  Contrariwise, if you *do*
        # define per-<VirtualHost> access logfiles, transactions will be
        # logged therein and *not* in this file.
        CustomLog "logs/access_log" common
        # If you prefer a logfile with access, agent, and referer information
        # (Combined Logfile Format) you can use the following directive.
        #CustomLog "logs/access_log" combined
    </IfModule>
    <IfModule alias_module>
        # Redirect: Allows you to tell clients about documents that used to
        # exist in your server's namespace, but do not anymore. The client
        # will make a new request for the document at its new location.
        # Example:
        # Redirect permanent /foo http://www.example.com/bar
        # Alias: Maps web paths into filesystem paths and is used to
        # access content that does not live under the DocumentRoot.
        # Example:
        # Alias /webpath /full/filesystem/path
        # If you include a trailing / on /webpath then the server will
        # require it to be present in the URL.  You will also likely
        # need to provide a <Directory> section to allow access to
        # the filesystem path.
        # ScriptAlias: This controls which directories contain server scripts.
        # ScriptAliases are essentially the same as Aliases, except that
        # documents in the target directory are treated as applications and
        # run by the server when requested rather than as documents sent to the
        # client.  The same rules about trailing "/" apply to ScriptAlias
        # directives as to Alias.
        ScriptAlias /cgi-bin/ "/sapcontreps/apache/cgi-bin/"
    </IfModule>
    <IfModule cgid_module>
        # ScriptSock: On threaded servers, designate the path to the UNIX
        # socket used to communicate with the CGI daemon of mod_cgid.
        #Scriptsock cgisock
    </IfModule>
    # "/sapcontreps/apache/cgi-bin" should be changed to whatever your ScriptAliased
    # CGI directory exists, if you have that configured.
    <Directory "/sapcontreps/apache/cgi-bin">
        AllowOverride None
        Options None
        Require all granted
    </Directory>
    <IfModule mime_module>
        # TypesConfig points to the file containing the list of mappings from
        # filename extension to MIME-type.
        TypesConfig conf/mime.types
        # AddType allows you to add to or override the MIME configuration
        # file specified in TypesConfig for specific file types.
        #AddType application/x-gzip .tgz
        # AddEncoding allows you to have certain browsers uncompress
        # information on the fly. Note: Not all browsers support this.
        #AddEncoding x-compress .Z
        #AddEncoding x-gzip .gz .tgz
        # If the AddEncoding directives above are commented-out, then you
        # probably should define those extensions to indicate media types:
        AddType application/x-compress .Z
        AddType application/x-gzip .gz .tgz
        # AddHandler allows you to map certain file extensions to "handlers":
        # actions unrelated to filetype. These can be either built into the server
        # or added with the Action directive (see below)
        # To use CGI scripts outside of ScriptAliased directories:
        # (You will also need to add "ExecCGI" to the "Options" directive.)
        #AddHandler cgi-script .cgi
        # For type maps (negotiated resources):
        #AddHandler type-map var
        # Filters allow you to process content before it is sent to the client.
        # To parse .shtml files for server-side includes (SSI):
        # (You will also need to add "Includes" to the "Options" directive.)
        #AddType text/html .shtml
        #AddOutputFilter INCLUDES .shtml
    </IfModule>
    # The mod_mime_magic module allows the server to use various hints from the
    # contents of the file itself to determine its type.  The MIMEMagicFile
    # directive tells the module where the hint definitions are located.
    #MIMEMagicFile conf/magic
    # Customizable error responses come in three flavors:
    # 1) plain text 2) local redirects 3) external redirects
    # Some examples:
    #ErrorDocument 500 "The server made a boo boo."
    #ErrorDocument 404 /missing.html
    #ErrorDocument 404 "/cgi-bin/missing_handler.pl"
    #ErrorDocument 402 http://www.example.com/subscription_info.html
    # MaxRanges: Maximum number of Ranges in a request before
    # returning the entire resource, or one of the special
    # values 'default', 'none' or 'unlimited'.
    # Default setting is to accept 200 Ranges.
    #MaxRanges unlimited
    # EnableMMAP and EnableSendfile: On systems that support it,
    # memory-mapping or the sendfile syscall may be used to deliver
    # files.  This usually improves server performance, but must
    # be turned off when serving from networked-mounted
    # filesystems or if support for these functions is otherwise
    # broken on your system.
    # Defaults: EnableMMAP On, EnableSendfile Off
    #EnableMMAP off
    #EnableSendfile on
    # Supplemental configuration
    # The configuration files in the conf/extra/ directory can be
    # included to add extra features or to modify the default configuration of
    # the server, or you may simply copy their contents here and change as
    # necessary.
    # Server-pool management (MPM specific)
    #Include conf/extra/httpd-mpm.conf
    # Multi-language error messages
    #Include conf/extra/httpd-multilang-errordoc.conf
    # Fancy directory listings
    #Include conf/extra/httpd-autoindex.conf
    # Language settings
    #Include conf/extra/httpd-languages.conf
    # User home directories
    #Include conf/extra/httpd-userdir.conf
    # Real-time info on requests and configuration
    #Include conf/extra/httpd-info.conf
    # Virtual hosts
    #Include conf/extra/httpd-vhosts.conf
    # Local access to the Apache HTTP Server Manual
    #Include conf/extra/httpd-manual.conf
    # Distributed authoring and versioning (WebDAV)
    #Include conf/extra/httpd-dav.conf
    # Various default settings
    #Include conf/extra/httpd-default.conf
    # Configure mod_proxy_html to understand HTML4/XHTML1
    <IfModule proxy_html_module>
    Include conf/extra/proxy-html.conf
    </IfModule>
    # Secure (SSL/TLS) connections
    #Include conf/extra/httpd-ssl.conf
    # Note: The following must must be present to support
    #       starting without SSL on platforms with no /dev/random equivalent
    #       but a statically compiled-in mod_ssl.
    <IfModule ssl_module>
    SSLRandomSeed startup builtin
    SSLRandomSeed connect builtin
    </IfModule>
    # uncomment out the below to deal with user agents that deliberately
    # violate open standards by misusing DNT (DNT *must* be a specific
    # end-user choice)
    #<IfModule setenvif_module>
    #BrowserMatch "MSIE 10.0;" bad_DNT
    #</IfModule>
    #<IfModule headers_module>
    #RequestHeader unset DNT env=bad_DNT
    #</IfModule>
    <IfModule mod_sapcs.cpp>
      AddModuleInfo ContentServer "SAP Content Server 640/0 (Prototype) (C) SAP AG 1998, 2001"
      CSConfigPath /sapcontreps/conf/cs.conf
      <Location /sapcs>
      SetHandler sapcs_module
      Allow from all
      </Location>
      <Location /ContentServer/ContentServer.dll>
      SetHandler sapcs_module
      Allow from all
      </Location>
      <Location /contentserver/contentserver.dll>
      SetHandler sapcs_module
      Allow from all
      </Location>
    </IfModule>
    Second parameter,
    rgdeverp:(/sapcontreps/apache/modules)(root)#ls -la /sapcontreps/apache/modules
    total 5544
    drwxrwxrwx  2 sapcs sapsys   4096 Jun 12 15:46 .
    drwxrwxrwx 15 sapcs sapsys   4096 Jun 12 14:56 ..
    -rwxrwxrwx  1 sapcs sapsys  13836 Jun 12 14:54 httpd.exp
    lrwxrwxrwx  1 sapcs sapsys     34 Jun 12 15:46 libsapsecu.so -> /sapcontreps/modules/libsapsecu.so
    -rwxrwxrwx  1 sapcs sapsys  34756 Jun 12 14:56 mod_access_compat.so
    -rwxrwxrwx  1 sapcs sapsys  31861 Jun 12 14:56 mod_actions.so
    -rwxrwxrwx  1 sapcs sapsys  44418 Jun 12 14:56 mod_alias.so
    -rwxrwxrwx  1 sapcs sapsys  30426 Jun 12 14:56 mod_allowmethods.so
    -rwxrwxrwx  1 sapcs sapsys  41605 Jun 12 14:56 mod_auth_basic.so
    -rwxrwxrwx  1 sapcs sapsys  84126 Jun 12 14:56 mod_auth_digest.so
    -rwxrwxrwx  1 sapcs sapsys  68399 Jun 12 14:56 mod_auth_form.so
    -rwxrwxrwx  1 sapcs sapsys  30531 Jun 12 14:56 mod_authn_anon.so
    -rwxrwxrwx  1 sapcs sapsys  36079 Jun 12 14:56 mod_authn_core.so
    -rwxrwxrwx  1 sapcs sapsys  40100 Jun 12 14:56 mod_authn_dbd.so
    -rwxrwxrwx  1 sapcs sapsys  32532 Jun 12 14:56 mod_authn_dbm.so
    -rwxrwxrwx  1 sapcs sapsys  32359 Jun 12 14:56 mod_authn_file.so
    -rwxrwxrwx  1 sapcs sapsys  49757 Jun 12 14:56 mod_authn_socache.so
    -rwxrwxrwx  1 sapcs sapsys  61854 Jun 12 14:56 mod_authz_core.so
    -rwxrwxrwx  1 sapcs sapsys  42581 Jun 12 14:56 mod_authz_dbd.so
    -rwxrwxrwx  1 sapcs sapsys  35071 Jun 12 14:56 mod_authz_dbm.so
    -rwxrwxrwx  1 sapcs sapsys  34704 Jun 12 14:56 mod_authz_groupfile.so
    -rwxrwxrwx  1 sapcs sapsys  35256 Jun 12 14:56 mod_authz_host.so
    -rwxrwxrwx  1 sapcs sapsys  30435 Jun 12 14:56 mod_authz_owner.so
    -rwxrwxrwx  1 sapcs sapsys  30802 Jun 12 14:56 mod_authz_user.so
    -rwxrwxrwx  1 sapcs sapsys 105072 Jun 12 14:56 mod_autoindex.so
    -rwxrwxrwx  1 sapcs sapsys  34253 Jun 12 14:56 mod_buffer.so
    -rwxrwxrwx  1 sapcs sapsys 192292 Jun 12 14:56 mod_cache.so
    -rwxrwxrwx  1 sapcs sapsys  84567 Jun 12 14:56 mod_cache_disk.so
    -rwxrwxrwx  1 sapcs sapsys  88616 Jun 12 14:56 mod_cache_socache.so
    -rwxrwxrwx  1 sapcs sapsys  98717 Jun 12 14:56 mod_cgid.so
    -rwxrwxrwx  1 sapcs sapsys 354271 Jun 12 14:56 mod_dav.so
    -rwxrwxrwx  1 sapcs sapsys 189761 Jun 12 14:56 mod_dav_fs.so
    -rwxrwxrwx  1 sapcs sapsys  59275 Jun 12 14:56 mod_dbd.so
    -rwxrwxrwx  1 sapcs sapsys  35504 Jun 12 14:56 mod_dir.so
    -rwxrwxrwx  1 sapcs sapsys  33559 Jun 12 14:56 mod_dumpio.so
    -rwxrwxrwx  1 sapcs sapsys  31544 Jun 12 14:56 mod_env.so
    -rwxrwxrwx  1 sapcs sapsys  40037 Jun 12 14:56 mod_expires.so
    -rwxrwxrwx  1 sapcs sapsys  63988 Jun 12 14:56 mod_ext_filter.so
    -rwxrwxrwx  1 sapcs sapsys  39211 Jun 12 14:56 mod_file_cache.so
    -rwxrwxrwx  1 sapcs sapsys  52811 Jun 12 14:56 mod_filter.so
    -rwxrwxrwx  1 sapcs sapsys  60936 Jun 12 14:56 mod_headers.so
    -rwxrwxrwx  1 sapcs sapsys 158790 Jun 12 14:56 mod_include.so
    -rwxrwxrwx  1 sapcs sapsys  66838 Jun 12 14:56 mod_info.so
    -rwxrwxrwx  1 sapcs sapsys  36196 Jun 12 14:56 mod_lbmethod_bybusyness.so
    -rwxrwxrwx  1 sapcs sapsys  36188 Jun 12 14:56 mod_lbmethod_byrequests.so
    -rwxrwxrwx  1 sapcs sapsys  36192 Jun 12 14:56 mod_lbmethod_bytraffic.so
    -rwxrwxrwx  1 sapcs sapsys  48496 Jun 12 14:56 mod_lbmethod_heartbeat.so
    -rwxrwxrwx  1 sapcs sapsys  86665 Jun 12 14:56 mod_log_config.so
    -rwxrwxrwx  1 sapcs sapsys  40163 Jun 12 14:56 mod_log_debug.so
    -rwxrwxrwx  1 sapcs sapsys  31797 Jun 12 14:56 mod_logio.so
    -rwxrwxrwx  1 sapcs sapsys  48254 Jun 12 14:56 mod_macro.so
    -rwxrwxrwx  1 sapcs sapsys  54195 Jun 12 14:56 mod_mime.so
    -rwxrwxrwx  1 sapcs sapsys 106526 Jun 12 14:56 mod_negotiation.so
    -rwxrwxrwx  1 sapcs sapsys 291551 Jun 12 14:56 mod_proxy.so
    -rwxrwxrwx  1 sapcs sapsys 171766 Jun 12 14:56 mod_proxy_ajp.so
    -rwxrwxrwx  1 sapcs sapsys 108144 Jun 12 14:56 mod_proxy_balancer.so
    -rwxrwxrwx  1 sapcs sapsys  54249 Jun 12 14:56 mod_proxy_connect.so
    -rwxrwxrwx  1 sapcs sapsys  38536 Jun 12 14:56 mod_proxy_express.so
    -rwxrwxrwx  1 sapcs sapsys  61607 Jun 12 14:56 mod_proxy_fcgi.so
    -rwxrwxrwx  1 sapcs sapsys 112538 Jun 12 14:56 mod_proxy_ftp.so
    -rwxrwxrwx  1 sapcs sapsys 114424 Jun 12 14:56 mod_proxy_http.so
    -rwxrwxrwx  1 sapcs sapsys  56400 Jun 12 14:56 mod_proxy_scgi.so
    -rwxrwxrwx  1 sapcs sapsys  55514 Jun 12 14:56 mod_proxy_wstunnel.so
    -rwxrwxrwx  1 sapcs sapsys  32760 Jun 12 14:56 mod_ratelimit.so
    -rwxrwxrwx  1 sapcs sapsys  40376 Jun 12 14:56 mod_remoteip.so
    -rwxrwxrwx  1 sapcs sapsys  45091 Jun 12 14:56 mod_reqtimeout.so
    -rwxrwxrwx  1 sapcs sapsys  37224 Jun 12 14:56 mod_request.so
    -rwxrwxrwx  1 sapcs sapsys 171049 Jun 12 14:56 mod_rewrite.so
    lrwxrwxrwx  1 sapcs sapsys     35 Jun 12 15:46 mod_sapcs22.so -> /sapcontreps/modules/mod_sapcs22.so
    -rwxrwxrwx  1 sapcs sapsys 119242 Jun 12 14:56 mod_sed.so
    -rwxrwxrwx  1 sapcs sapsys  57944 Jun 12 14:56 mod_session.so
    -rwxrwxrwx  1 sapcs sapsys  32806 Jun 12 14:56 mod_session_cookie.so
    -rwxrwxrwx  1 sapcs sapsys  47023 Jun 12 14:56 mod_session_dbd.so
    -rwxrwxrwx  1 sapcs sapsys  44102 Jun 12 14:56 mod_setenvif.so
    -rwxrwxrwx  1 sapcs sapsys  53976 Jun 12 14:56 mod_slotmem_shm.so
    -rwxrwxrwx  1 sapcs sapsys  45214 Jun 12 14:56 mod_socache_dbm.so
    -rwxrwxrwx  1 sapcs sapsys  35686 Jun 12 14:56 mod_socache_memcache.so
    -rwxrwxrwx  1 sapcs sapsys  68519 Jun 12 14:56 mod_socache_shmcb.so
    -rwxrwxrwx  1 sapcs sapsys  39669 Jun 12 14:56 mod_speling.so
    -rwxrwxrwx  1 sapcs sapsys  63924 Jun 12 14:56 mod_status.so
    -rwxrwxrwx  1 sapcs sapsys  43320 Jun 12 14:56 mod_substitute.so
    -rwxrwxrwx  1 sapcs sapsys  33237 Jun 12 14:56 mod_unique_id.so
    -rwxrwxrwx  1 sapcs sapsys  33466 Jun 12 14:56 mod_unixd.so
    -rwxrwxrwx  1 sapcs sapsys  33615 Jun 12 14:56 mod_userdir.so
    -rwxrwxrwx  1 sapcs sapsys  25961 Jun 12 14:56 mod_version.so
    -rwxrwxrwx  1 sapcs sapsys  37707 Jun 12 14:56 mod_vhost_alias.so
    But when stop or stat I have the error,
    rgqaserp:(/sapcontreps/apache/bin)(root)#./apachectl start
    httpd: Syntax error on line 66 of /sapcontreps/apache/conf/httpd.conf: Cannot load modules/mod_sapcs22.so into server: /sapcontreps/apache/modules/mod_sapcs22.so: ELF file data encoding not little-endian
    Can you help me?
    Thanks

  • Http error 405 method not allowed sap content server windows

    Hi Expert,
    we have install sap content server 6.5 on microsoft windows 2012 using
    IIS 8.0 and MAXDB 7.9 SP 8 Build 21. After configuring the content server it self we still cannot
    create repository error "http error 405 method not allowed"
    Oac0 --> tab Create --> Content rep.
    I have implement note number 1704365 - IIS roles not created by
    default when installing Content Server on Windows 2008. even though it
    is not applicable to our IIS.
    when i try to open http://hostname:1090/ContentServer/ContentServer.dll?serverInfo
    it always direct us to download file not showing the version number.
    is there any solution for this issue?
    Thanks a lot,

    Dear,
    Can you please try following URL ?
    http://hostname:1090/ContentServer/ContentServer.dll?serverInfo&pVersion=0046
    http://hostname:1090/ContentServer/ContentServer.dll?serverInfo&pVersion=0046&contRep=<Repository Name>
    Regards
    S S B

  • SAP Content Server Configuration (CSADMIN) error in connection

    Dear Colleagues
    I have installed SAP Content Server 6.40 on Windows 2008 R2 server (64 bit) using IIS 7.5 with MaxDB 7.8.02, Installation completed successfully.
    URL testing Information on both Content Server and an Instance which we need to connect to it.
    http://cs460:1090/ContentServer/ContentServer.dll?serverInfo
    serverType="SAP HTTP Content Server";serverVendorId="Copyright SAP AG, All rights reserved 1998, 2001  ";serverVersion="6400";serverPatch="9";serverBuild="201";pVersion="0046";serverStatus=
    "running";serverStatusDescription="";serverDate="2014-05-11";serverTime="02:03:08";startUpDate="2014-05-11";startUpTime="02:03:08";lastAccessDate="2014-05-11";lastAccessTime="02:03:08";
    However, when I try to create repository with CSADMIN tcode, I am getting error ''HTTP error: 500 (Internal Server Error)'.
    database host is up or down and the web server up
    My settings are as follows
    1- On Content server I give full permission to content Rep directory
    2- On IIS I have allowed Unspecified ISAPI& CGI & modules.
    3-odbcreg as the following:-
    C:\sapdb\SDB\db\pgm>odbcreg -g
    List of installed drivers
    1.      SQL Server;     %WINDIR%\system32\SQLSRV32.dll
    2.      SAP MaxDB SDB (Unicode);        C:\sapdb\SDB\db\pgm\sdbodbcw.dll
    3.      SAP MaxDB SDB;  C:\sapdb\SDB\db\pgm\sdbodbc.dll
          C:\sapdb\SDB\db\pgm>odbcreg MaxDB -i -p c:\sapdb\SDB\db\pgm -d sdbodbcw.dll
    ODBC Driver for 'MaxDB' has been successfully registered.
         C:\sapdb\SDB\db\pgm>odbcreg MaxDB -i -p c:\sapdb\SDB\db\pgm -d sdbodbc.dll
    ODBC Driver for 'MaxDB' has been successfully registered.
    4- under settings tab for the repository I set the parameter (driver = MaxDB) as per SAP note 977091
    Please suggest, how to resolve this issue.
    Thanks

    HI Hany Zahran,
    Hope that your issue resolved? if so please close this thread with updated answer and make sure mark assumed answered (see top of the screen).
    All the best my dear fnd.
    Regards,
    chandu.

  • Moving SAP Content Server/MaxDB 7.6 to a Windows 2008 R2 Server

    Hi All.
    We are in the process of upgrading our server where the SAP content server is located.  We are going from SAP CS 6.30/MaxDB 7.6 to a Windows 2008 R2 server where we want to install SAP CS 6.40/MaxDB 7.8.  I have been following the latest manual from SAP for upgrading to MaxDb 7.8  (2010-10-05) from MaxDb 7.6 using the in-place method.
    To date we have installed MaxDB 7.6 on the server.  We restored our latest backup and performed the index checks as spelled out in the manual.  I have the database in ADMIN mode and went to run the MaxDb 7.8 install for the 64 bit window version.  THe install GUI comes up, but the Update selection is grayed out.  This tells me that the install program can not detect our existing database.  I did make sure I was running the install as Admim so I do not think that is the issue.
    This is the second time I have tried this upgrade.  The first time I did a comand line upgrade by runing the .bat file DBUPDATE.bat. We have a 110 Gbyte database and this upgrade ran in about 15 minutes, and of course when I went to openthe database it was toast.  Do not want to make the same mistake again.
    One other point, since we did a restore of the database, then the index check, we did not run a backup as the manual suggested as we felt it was not necessary.  Does the system require a backup before upgrade and that is why it does not see the database?
    Any assistance will be greatly appreciated.

    I beleive we have resolved the issue with upgrading the database, but now we are having a problem with Datbase Studio 7.8.  Before the upgrade we used Data Manager 7.6.  After the upgrade we installed Database Studio 7.8 and when we go to start it up, we are getting the Problems opening perspective 'com.sap.sdb.tools.ut.perspectives.mainPerspective'. I followed the instruction in another post Problems opening perspective in Database Studio, but we still are getting the error.
    Can anybody offer any assistance as we are getting close to the weekend when we want to do the cutover and we are not even done with our first pass at upgrading the SAP content server.
    Thanks
    John

  • SAP Content Server 6.40 on Windows 2003, IIS 6, filesystem storage

    Hello:
    We have installed SAP Content Sever 6.40 on Windows Server 2003, IIS 6, and using the filesystem as storage, not SAPDB.
    The installation goes without any issues and completes successfully, but the test URL http://<host>:<port>/ContentServer/ContentServer.dll?serverInfo returns "The page cannot be displayed" and not the expected system info/status. We need to fix this before moving on to config in ERP, any suggestions into Content Server or IIS settings/configuration is appreciated.
    We're using the standard install port 1090, and testing from a browser in the same host.
    Regards,
    Eduardo

    Additional information:
    Looking in the event viewer under application, I see the following 2 errors:
    1) The HTTP Filter DLL D:\Program Files\SAP\Content Server\ContentServer.dll failed to load.  The data is the error.
    Data: 0000: 0000007f
    2) Could not load all ISAPI filters for site/service.  Therefore startup aborted.
    Regards,
    Eduardo

  • SAP Content Server 6.40 on 32 or 64 bit OS?

    Hi all,
    Can anyone tell me if SAP Content Server 6.40 on NW 2004s with MaxDB 7.6 will run on Windows 2003 64 or 32 bit? I have installed in on a x64 bit 2003 server now, but there seems to be some issues. For starters, I get the following error message when I try to run "http://<hostname>:<portno.>/ContentServer/ContentServer.dll?serverInfo" as part of the post-processing when installing SAP Content Server 6.40:
    %1 is not a valid Win32 application.
    Does anyone have any ideas?
    Regards,
    Thomas

    Hello,
    Currently, SAP Content Server do not support on Windows 64 bit system.
    Please install on 32 bit system.
    SAP CONTENT SERVER 6.40 -> MAXDB -> <WINDOWS SERVER...  >:
    MAXDB 7.6  WINDOWS SERVER 2003/IA32 32BIT
    If you are SAP customer, you will find more detailed information about
    availability in the SAP Product Availability Matrix (PAM) at 
    http://service.sap.com/pam (This is the official source for all SAP
    Netweaver-related availability information.)
    http://service.sap.com/pam  -> SAP NETWEAVER -> SAP NETWEAVER 20004S
    -> Database Platforms -> Content Server -> MAXDB -> <WINDOWS SERVER... >
    < See the SAP note 919225 for Windows IA32 system requirements.>
    Thank you and best regards, Natalia Khlopina

Maybe you are looking for

  • Clients with no internet access

    We have many servers whose IP address is blocked from receiving any internet traffic. The block is done in the ACLS of the edge router not in a firewall. Some organizations on campus have requested this for security reasons. These systems are unable

  • Using Outlook (2010 & 2013) to connect to Exchange using EWS

    First things first. I know that Outlook on the PC platform uses MAPI to connect to Excahnge while the Mac flavor of Outlook uses EWS, however, i was cycling through some available EX and ExO PowerShell cmdlets and found a parameter for set-casmailbox

  • Printing the Name and State of Servers

    Hi, Please can somebody help in executing the below mentioned code which will print the name and state of the servers. Below Java file taken from the following location : http://docs.oracle.com/cd/E23943_01/apirefs.1111/e13951/core/index.html import

  • Pass parameter to report paramater form from a form

    I defined parameter in a form. I am trying to pass the parameters to a report's parameter form. Is there any way to accomplish this? Thank you!

  • Pc to mac transfer ........ almost there -please HELP me complete!

    Successfully have moved all music, artwork, vids, podcasts from PC to MAC... moved the iTunes files across, and my playlists are present, but in name only..the associated music to playlist didn't connect.... Two different questions.. 1) do I need to