SAP PI FTP sender adapter not working with SAP ECC over Itanium

Hi,
We have been running normally SAP PI 7.0 SP14 with no issue for a while.
We are now in the process of migrate the SAP ECC system from PA risc to IA platform. We are performing some tests between SAP PI and SAP ECC to check that the platform migration is not affecting us in any way and we have found that FTP adapter sender is not working anymore (receiver is working as usual).
We place some files in the new ECC system and when PI goes to retreive the files it is like it can not read anything. It gives no error but it does not pick any file. This is not happening with the old platform.
Does anyone have any idea?
Thanks a lot for your help
Diana

Hi,
I am using FTP connection and for the receiver it is working fine.
Thanks
Diana

Similar Messages

StarTech Adapter not working with Dell Inspiron 15, model 3521

Side Note: I wrote a reply to a thread that was from 2013. I do apologize because the link was sent to me by my bf and I did not realize how old it was. Since my reply has to be approved I can't delete it.
Current Issue: StarTech Adapter not working with Dell Inspiron 15 model 3521
I bought my Dell laptop last year and at first I did not realize that it had only one audio jack (combo, as the specifications manual says), I only noticed when I was trying to plug in my Ozone Rage ST headset.
I searched online threads and found out that I needed an adapter and most people mentioned Headset Buddy. I couldn't find any adapters for sale in my country (or employees didn't really know what I was talking about) and since Headset Buddy is a bit expensive, I decided to try StarTech Headset adapter for headsets with separate headphone/microphone plugs - 3.5mm 4 position to 2x 3 position 3.5mm M/F www.amazon.com/.../ref=cm_cr_pr_product_top.
It arrived today and let me tell you that I can't make it work. I can hear everything but I can't get the external mic to work or even be detected. I have always used my headset (mostly for gaming) and I prefer to use my external mic rather than the internal one. First I connected my headphone and mic jacks to the adapter and only after that did I connect it to the laptop combo jack. I also tried vice-versa. It didn't work, regardless of the order. I even tried with a different headset and it still didn't work. What else can I do?
I have also found a thread on Dell forums saying that Headset Buddy doesn't even work on Dell Inspiron 15, model 3521. So since it doesn't work and I'm assuming StarTech doesn't, either, what am I to do/buy?! I am getting extremely frustrated and I'm very disappointed with Dell because the brand should have included with the laptop a proper working adapter for these situations and not make its customers buy an extra accessory to make whatever working gear they already had function. It just doesn't make sense to me! Either make the changes work properly or simply don't touch anything. I spent some of my savings on this laptop which, overall, is great but now I am being forced to spend more on an item to allow me to use my headset. I am running out of options here and even Dell can't seem to tell its customers with 100% certainty what really works for this specific model.
If I can't make the adapter work, I just hope I can return it, otherwise I'll end up with no refund and with a piece of equipment I have no other use for!
Any thoughts?

Hi,
Thanks for your reply.
This is the first time I was forced to buy adapters such as these so I don't know if I'm doing something wrong or if there's anything else I can do to make it work. When I plug the adapter to my Dell, the laptop presents me with several options such as: headphones, headphone, speakers, skull candy headphones, etc (maybe some may have different names but since I see them in Portuguese, I'm not quite sure how they appear for someone who has the computer in English), I have picked different options and it still doesn't work, the only noticeable changes are sound quality related, I guess.

Why does my digital AV adapter not work with my iPad

Why does my digital AV adapter not work with my iPad

i was going to try it on a flat screen hdmi input, but just as i plug the apple digital av adapter in to my ipad it says "this accessory is not supported by ipad"... my itouch says the same thing... any ideas?

HTMLDB_MAIL.SEND does not work with 11g

Hi Guys,
I have a simple application that uses HTMLDB_MAIL.SEND. I am running APEX 3.0 against an 11g database. When run against a 10g DB all is good. But with 11g I get
ORA-24247: network access denied by access control list (ACL)
I looked up the error which recommends altering ACL stuff, which I know nothing about. Is there a simple way to get rid of this error.
O.

Hi,
I have the same problem as you.
Colud you please explain me how did you resolve it.
Thanks
HTMLDB_MAIL.SEND does not work with 11g

FTP-Sender Adapter ignores files with "known filenames"

Hello experts,
the scenario is FTP -> XI -> IDOC and we have problems with the polling of the files. In communication channel monitoring everything is working fine, but in the FTP folder some files are ignored, although the communication channel is set up for all *.txt-files.
My question is, is it possible that the FTP sender adapter ignores files, if it already has processed a file with the same filename? After renaming the files they all were picked up and archived into another folder. How can I configure the communication channel to pick up ALL *.txt-files in the out-folder?
Best regards
David

Hi David,
What I have observed is, XI always reads files in a certain order (possibly alphabetical or reverse alphabetical). If it finds a file in the source directory that already exists in the archive directory, it will not attempt to read/process the next file (even if the next filename is completely new).
So, if any of the files in the source directory exist in the archive directory, there is a possibility that certain files may get processed and certain wont.
Make sure that none of the files that you put in source directory exist in the archive directory (i.e. all the files are new) and see the output. Let me know if this helps.
PS: I used FTP protocol
Regards,
Riyaz

Av adapter not working with ipad 2, please advice

I bought an av adapter 2012 release, is not working with my ipad 3g att ios version 4.3.5 i tried reset, changing the widescreen button multiple times no luck no video mirroring or sound. When i plug there is a msg displayed: accessory not supported.
I have 2 questions :
1) is this a ios version ? There a lot people complaining that after updates the adapter stopped working, if it is is this version w abug?
2) can i update the ios to 5.x not the ios 6 or i m forced to update to the last version ?

See the following where it states the requirement of iOS 5.1 or later (in the features box)
http://support.apple.com/kb/HT4108?viewlocale=en_US
And yes, you should be able to update to iOS 5.1 without going directly to iOS 6. You need to locate the correct .ipsw update file for your iPad 2 and manually install it through iTunes. Google "ios ipsw 5.1.1" for links to the iOS 5.1.1 files.

Mini dvi to dvi adapter not working with monitor

arright *** i got a mini dvi to dvi adapter which is connected to my vga monitor through a vga to dvi adapter. The computer recognizes the monitor in display preferences, but the monitor doesn't display anything it just sits in standby mode... any ideas why this isn't working? You'd think if the problem was going from vga-vga to dvi adapter-dvi to mini dvi adapter that it wouldn't even recognize the monitor but it does.
well that *****, back to best buy to get the other one. Reason i got the dvi one is because i plan on getting a different monitor with dvi soon. But noo dvi adapter wont work with vga adapters.
Message was edited by: Veiss

The mini-DVD to DVI adapter doesn't pass through the analog video signals needed for VGA, so won't work with a DVI to VGA adapter. All the control signals are there, so the display is recognized, but there will be no picture.
They could have used a DVI-D connector on the adapter, instead of DVD-I, so the DVI to VGA adapter wouldn't even plug in, but then it couldn't be used with some non-Apple LCDs, that use DVD-I connecters.

Sender FTP Adapter not working with certain name

Hello,
We're facing the next problem within XI.
We configured a sender FTP adapter within the central adapter engine. This adapter is configured correctly however for some reason it is not picking up any file from the FTP server.
Changing status to inactive-> active again all kinds of modes and configs we tested.
However when copying this non-working adapter to a new one with a different name (Configuration is exactly the same!!!!!) and use this one in the sender agreement it worked immediately.
Somebody else faced similar problems and managed to solve it because for this error we don't want to adjust our naming conventions....
Thanks,
Emile

Hi Emile,
This could happen when AE cache is not getting updated.
Goto SXI_CACHE.
Click "Goto" -> AE Cache and check if you get a green symbol with a message saying " Cache contents are up-to-date".
Regards,
Anish

Thunderbolt to VGA Adapter not working with SMART board all of a sudden?

I was wondering if anyone had any suggestions on getting my classroom's (I'm student teaching) SMART board connected to my macbook pro (13 in). Two days ago I tested the setup I had, Mini-DVI to VGA adapter, Mac OS X SMART software suite and it worked flawlessly. Today I try the setup and although the SMART board recognizes my macbook via usb, the projector does not display anything. System preferences does not even recognize the projector as an external monitor. When I plug in my Mini-DVI to VGA adapter (already attached to the VGA cord from the SB) the screen flashes black and goes back to normal. Official work from SMART technologies is there is no supported adapters for connecting a macbook to a SB but I have seen numerous threads about this setup working and like I said it was previously working fine. Any suggestions on what to try next? I was thinking of dual booting to an older version of OS X. Thanks.
Specs:
MacBook Pro 13 in
2.4 GHz Intel Core 2 Duo
4 GB 1067 MHz DDR3
10.9.1

If your laptop is not connected to power (i.e., plugged in to a wall), try plugging it in. It is not uncommon for a laptop to send the VGA signal out with less power when it is on battery power. I've seen this fix this problem, at least, dozens of times.
Try connecting the VGA cable to your adapter while the smart board display is on THEN plug the adapter in to your computer.
Also, try connecting the VGA+Adapter to your mac before booting it (or connect the macbook to the vga cable and then reboot the macbook). I've seen this work with macbooks using vga on projectors (or other external displays running through longer cables or crestron/extron/whatever switching equipment) many many times too.
If these fail, get your campus AV (or IT) people involved. We have often found that a damaged cable or long run needing amplification will work with some computers but not with others. It could be that the cable running from the smart board is somewhat sketchy.
Also, have you attempted to connect your macbook to any other display since starting to have the issue? A bad dongle (dp to vga adapter) isn't rare. I have a bad one sitting on my desk at this very moment.
One last thing you can try, this works for some:
Shut of the mac
Connect it to the smart board (i.e, connect the cables)
Turn on the mac and then close the lid
This *may* boot the computer on the external dispaly (smart board)
Open the lid before it comes to the login screen.
Hopefully one of these suggestions helps.

Delete Operation in JDBC Sender Adapter not works

Hi,
    I have one student table which contains the fields ID,Name,BirthMonth,BirthYear,ReadFlag fields. ReadFlag is a character field or lenght 1 which contains only values either 'Y' or ' '.
     I want to execute delete operation in this table ie to delete the records which contains the readflag = 'Y'. So, I set the below values for the following parameters.
DELETE FROM student WHERE READFLAG = ' Y '
Query SQL Statement : SELECT * FROM student WHERE readflag = 'Y'
Update SQL Statement : DELETE FROM student WHERE READFLAG = 'Y'
Poll Interval : 60 Seconds.
    There are more records in this table which contains readflag = 'Y'. But, the Adapter does not delete those records from the table i.e delete operation is not executed. At the same time, in Comm. Channel monitoring it does not show any error, but the delete operation is not carried out in the table.
     I tried after 'COMMIT' the table also. But it does not work. What could be the reason ? or How to use Delete Operation effectively on the table ?
     Kindly help me friends to solve this problem.
Thanking you.
Kind Regards,
Jeg.

http://help.sap.com/saphelp_nw04/helpdata/en/7e/5df96381ec72468a00815dd80f8b63/content.htm >>>
<i>Adapter Work Method
You must add an indicator that specifies the processing status of each data record in the adapter (data record processed/data record not processed) to the database table.
The UPDATE statement must alter exactly those data records that have been selected by the SELECT statement. You can ensure this is the case by using an identical WHERE clause. (See Processing Parameters, SQL Statement for Query, and SQL Statement for Update below).
<b>Processing can only be performed correctly when the isolation level for transaction is set to repeatable_read or serializable.
Example
SQL statement for query: SELECT * FROM table WHERE processed = 0;
SQL statement for update: UPDATE table SET processed = 1 WHERE processed = 0;
processed is the indicator in the database.</b></i>
try with repeatable_read or serializable !!!
Also go thru this thread - DELETE Querey in JDBC SENDER

SOAP Sender Adapter Not working

We have the following Synchronous sceanrio: Third Party System <> PI <> SAP ECC
The interface works well in our DEV and PreProd environments but has stopped working in our QA environment.
The SOAP Sender Adapter is giving me the following error:
failed to initialize: org.apache.axis.ConfigurationException:
java.lang.ClassNotFoundException: ------------------------- Loader Info -------------------------
ClassLoader name: library:com.sap.aii.af.axisproviderlib] Living status: alive Direct parent loaders:   system:Frame   library:com.sap.base.technology.facade   library:engine.j2ee14.facade] Resources:
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/axis.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/commons-discovery-0.2.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/commons-logging-1.0.4.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/commons-net-1.0.0-dev.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/wsdl4j-1.5.1.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/xmlsec-1.4.0.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/wss4j-1.5.6.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/opensaml-1.0.1.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/xalan-2.6.0.jar
Currently the Quality of Service for the communication channel is set to "Best Effort" because it is a Synchronous Interface. However if I change the Quality of Service to "Exactly Once" the message is received by PI without any problems. So the problem is specific to Synchronous.
I tried to create a new communication channel and use that but that didnt help.
We have checked on the server and all the above mentioned .jar files are all in place.
I have compared the Processing Sequence and Module Configuration of the Module tab (for the communication channel) with the other environments and everything seems to be fine.
Any help would be much appreciated.
Thanks,
Krishneel

Hi Krishna,
ClassLoader name: library:com.sap.aii.af.axisproviderlib] Living status: alive Direct parent loaders:   system:Frame   library:com.sap.base.technology.facade   library:engine.j2ee14.facade] Resources:
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/axis.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/commons-discovery-0.2.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/commons-logging-1.0.4.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/commons-net-1.0.0-dev.jar
/usr/sap/XQ1/DVEBMGS01/j2ee/cluster/bin/ext/com.sap.aii.af.axisproviderlib/lib/wsdl4j-1.5.1.jar
Have you deployed the following Jar.
commons-discovery-0.2.jar
○       commons-logging-1.0.4.jar
○       commons-net-1.0.0-dev.jar
○       wsdl4j-1.5.1.jar
Refer this
http://help.sap.com/saphelp_nw04/helpdata/en/45/a4f8bbdfdc0d36e10000000a114a6b/content.htm
Edited by: Debashish Roy on Jul 18, 2011 10:10 AM

'Keep Header' Option in SOAP sender adapter not working

Hi all
I have exposed a webservice using a SOAP sender adapter in XI. A SOAP client is sending request to this service.
The SOAP request has some elements in the header like wssecurity and ws addressing tags.
When I remove the header elements and send the request my scenario works as expected but when I include the header fields I get a time out in my soap client application and cannot see any message, any where on XI. Can somebody help me understand why this is happening.
Thanks
Dilip

Hi Stefan
In my scenario it is ok if XI ignores the soap header tags it does not understand. I want the system to ignore the header tags and go ahead and process only the payload.
But unfortunately I keep getting a time out whenever I send a request with the header tags. When I remove the header I can sucessfully post documents.
I tried increased the time out to 5 min but still continue to get the problem. So am sure the problem is not exactly related to timeout, but due to the header tags.
What do you suggest?
Regards
Dilip

Lightning HDMI Adapter not working with iOS 6.1.2

I have an iPhone 5 which was updated from 6.0.2 to 6.1.2 recently and the Lightning HDMI adapter stopped working altogether for video mirroring; was wondering if anyone has the same situation/any solution for this?
I also have an iPad retina generation which is at 6.1.2, and the Lightning HDMI adapter is not working for it as well.
I've tried replacing HDMI cables, rebooting the iPhone with the cable plugged in, and plugging out/in several times with the charger in/out. The adapter works, cause when I plug it in; I see the top bar flash for a bit... but no dice on the video mirroring to my TV.

I also have this problem and am very unhappy with the way Apple is handling it. Called today to enquire on when the fix will be available and was told it is a software issue that could be fixed if we paid $35.00 to talked through process on the phone. Highly disappointed with Apple, why should it cost me money for them to fix there own issue. Since they are aware of the issue the least they can do it posted the information for the fix online @ no charge.
If I wanted crap service I could have gotten a phone from anyone. Reconsidering purchasing a 5 on next upgrade.

Rocketfish adapter not working with MacBook Pro 13 inch

I have a rocketfish HDMI to mini displayport adapter. I have tried to connect it to a 22 inch monitor and a 50 inch TV as an extended monitor but the MacBook does not recognize the extended display.
Any ideas on how to resolve or is the adapter not supported?

Check this post if you want more info:
http://discussions.apple.com/thread.jspa?threadID=2774718
The gist is that DVI is currently very iffy through Thunderbolt. Mini display -> mini display OR mini display -> HDMI should work fine. It's most likely not your adapter itself but the fact that it's DVI.
If you can, get a mini display -> HDMI adapter and try that (assuming your external has HDMI).
I should hear back tomorrow or Monday from apple engineers with more specific info about this issue and I will update then.
BTW- DVI anywhere in the chain will make things fail. Mini Display -> DVI and a DVI/HDMI cable won't work with any reliability (I've tested it on three completely different monitors).

300N Router/Adapter not working with Satellite internet

I had previously SRX200 router and it was working fine with Satellite but recently I bought again 300N router and adapter but it's not working. It give the strong signal for few seconds and drops it rightway. Please let me know if there is something I need to do with settings.
Thanks
Paul

Paul make sure that the firmware of this router is upgraded to the latest version 1.03.0, it resolves a lot of issue.

SAP PI FTP sender adapter not working with SAP ECC over Itanium

Similar Messages

Maybe you are looking for