SAPOSCOL Problems with Shared Memory

Has anyone had any problems in either starting the saposcol or with keeping it running? We have noticed multiple problems for several years now, and are at a point where the saposcol is not running at all on any of our servers, nor can we start it running.
We're seeing "SAPOSCOL not running ? (Shared memory not available)". I am working with SAP with two different customer messages trying to determine why we cannot start the saposcol.
Does anyone have any ideas?
Thanks,
Traci Wakefield
CV Industries

I do have entries in the os-collector log:
      SAPOSCOL version COLL 20.89 640 - AS/400 SAPOSCOL Version 18 Oct 2005, 64 bit, single threaded, Non-Unicode
      compiled at   Nov 26 2005
      systemid      324 (IBM iSeries with OS400)
      relno         6400
      patch text    COLL 20.89 640 - AS/400 SAPOSCOL Version 18 Oct 2005
      patchno       102
      intno         20020600
      running on    CENTDB1 OS400 3 5 0010000A1E1B
13:25:06 28.02.2007   LOG: Profile          : no profile used
13:25:06 28.02.2007   LOG: Saposcol Version : [COLL 20.89 640 - AS/400 SAPOSCOL Version 18 Oct 2005]
13:25:06 28.02.2007   LOG: Working directory : /usr/sap/tmp
13:26:01 28.02.2007   LOG: Shared Memory Size: 339972.
13:26:01 28.02.2007   LOG: INFO: size = (1 + 60 + 3143) * 106 + 348.
13:26:01 28.02.2007   LOG: Connected to existing shared memory.
13:26:01 28.02.2007   LOG: Reused shared memory. Clearing contents.
13:26:04 28.02.2007   LOG: Collector daemon started
13:26:04 28.02.2007   LOG: read coll.put Wed Feb 28 13:22:01 2007
13:26:04 28.02.2007   LOG: Collector PID: 2469
13:27:05 28.02.2007   LOG: Set validation records.
14:00:32 28.02.2007 WARNING: Out of int limits in pfas41c1.c line 1528
12:58:37 10.03.2007   LOG: Stop Signal received.
12:58:38 10.03.2007   LOG: ==== Starting to deactivate collector ==========
12:59:01 10.03.2007   LOG: ==== Collector deactivated ================
Also, I have tried saposcol -d (and other parameters below):
saposcol -d
kill
clean
leave
quit.
delete the files coll.put, dev_coll"
4" From my open SAP message:
I have also done the following:
1 Check the authorizations of SAPOSCOL as mentioned in SAP Notes:
637174 SAPOSCOL cannot access Libraries of different SAP systems
175852 AS/400: Authorization problems in SAPOSCOL
2 Remove the shared memory (coll.put)
(according to SAP Note: #189072). You could find 'coll.put' in path:
'/usr/sap/tmp'.
3 End the following jobs in QSYSWRK:
QPMASERV, QPMACLCT, QYPSPFRCOL and CRTPFRDTA
4 Delete the temporary user space:
WRKOBJ OBJ(R3400/PERFMISC) OBJTYPE(USRSPC)
Afterwards you could start SAPOSCOL on operating system level.
Just logon to iSeries as <SID>OFR and run the following command:
SBMJOB CMD(CALL PGM(<kernel_lib>/SAPOSCOL) PARM('-l'))
JOB(SAPOSCOL) JOBQ(R3<SID>400/R3_<nn>)
LOG(4 0 SECLVL) CPYENVVAR(YES)
Thanks,
Traci"

Similar Messages

My host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

my host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

There are several possible causes for this problem.
1. Two (or more) computers on the local network have the same Bonjour name, such as "X's-MacBook-Pro.local".
2. You have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
3. A Mac wakes from sleep due to network traffic. This is due to a bug in OS X that may only affect some models.
4. A device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
5. A third-party wireless router has incompatible settings or firmware. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
6. See also this support article.
Rename the computer in the Sharing preference pane.

TPC 2012 - Problems with shared variable

Hi,
I tried to program simmilar thing to this one http://zone.ni.com/devzone/cda/tut/p/id/5548 on TPC 2012. But it doesn't work.I can see that both programs on my laptop and TPC are working(I've added an additional counter with display), but I cannot see any effect on TPC when I change the value of shared variable on my laptop. I use LabView 8.6 with Touch Panel Module. My question is what are the exact steps to run such application on TPC2012? Are they the same as for TPC 2006?
I've noticed following issues:
1.I cannot deploy the program from Project Manager(there is an information that maybe TPC Service is not started. - I've found such information about TPC Service http://digital.ni.com/public.nsf/allkb/DE177828D27A14A48625734E00768B66 but in fact I cannot find Start » All Programs»National Instruments » NI TPC Service » NI TPC Service Manager 1.0 Does it mean, that the TPC Service is not installed and the programm with shared varibles won't be working or can I start it somehow in another way? Do I need to have TPC service installed on TPC2012?
Until now, I've built the project and sent it through FTP to TPC(the folder was /TEMP) and then started it.
2.Ping works OK
Thank you in advance for any hints how to solve this problem.
Martin

Well no problem, but I'm frustrated with this issue... I've tested many things and nothing. Just to help someone else as I in the future, these are my sources:
http://forums.ni.com/t5/LabVIEW/TPC-2012-Problems-with-shared-variable/m-p/1009631/highlight/false#M...
http://digital.ni.com/public.nsf/allkb/28536DE7E2D9E98B8625770B00738920?OpenDocument
http://zone.ni.com/reference/en-XX/help/372507B-01/lvtpcgsm/tpc_install_sharvar/
http://zone.ni.com/reference/en-XX/help/372507C-01/lvtpcgsm/tpc_install_sharvar/
http://digital.ni.com/public.nsf/allkb/23532363F4905EC28625727A00730B80?OpenDocument
http://forums.ni.com/t5/FieldPoint-Family/TPC-2006-Not-Listed-in-Targets-and-Devices/td-p/566325
http://forums.ni.com/t5/LabVIEW/MAX-can-t-detect-TPC-2106T/td-p/831524
http://zone.ni.com/devzone/cda/tut/p/id/5868
http://digital.ni.com/public.nsf/websearch/28B748B9697B79E18625725A00009066?OpenDocument
http://digital.ni.com/public.nsf/websearch/D1726990DCEB82E4862570F20069C57D?OpenDocument
http://digital.ni.com/public.nsf/allkb/3B469103BBDD4CE48625726000665B36
I hope find some hint..
Fabian León
Certified LabVIEW Associate Developer

Problem with shared objects synchoronization.

I encountered a small problem with shared objects.
I'm working on a program that creates chat rooms of a fixed
size of 30 users. When the 31th user comes, a new room is created.
The idea is that the client first connects to the first room
and checks if it's full by connecting to shared objects. If it is
full, connection is closed and process is reapeated on a new
instance of the application.
I use a function to connect to an instance, which takes as a
parameter a number (1 for instance room_1, 2 for room_2, etc). The
function itself creates the necessary Netconnection and
sharedObject objects.
If a room is full, Netconnections and sharedObjects are
closed and function is called again with another number.
I have no problem for connecting to the first room, but after
closing the first connection and connecting to the new room, there
seem to be some problems with the shared objects (especially,
OnSync doesn't seem to execute again after the connection to the
shared objects of the new instance).
I was wondering if you had any ideas what could cause this.
Is it the use of the same variable names for connecting at two
different shared objects?
Here is the function :
function initStreams(room) {
client_nc = new NetConnection();
client_nc.connect("rtmp://192.168.0.4/Elearning/room_"+room);
in_ns = new NetStream(client_nc);
in_ns2 = new NetStream(client_nc);
Replay_video.attachVideo(in_ns);
out_ns = new NetStream(client_nc);
out_ns2 = new NetStream(client_nc);
in_ns.play("my_recorded_stream");
users_name = SharedObject.getRemote("users_name",
_root.client_nc.uri, false);
users_name.connect(_root.client_nc);
users_language = SharedObject.getRemote("users_language",
_root.client_nc.uri, false);
users_language.connect(_root.client_nc);
users_picture = SharedObject.getRemote("users_picture",
_root.client_nc.uri, false);
users_picture.connect(_root.client_nc);
users_finger = SharedObject.getRemote("users_finger",
_root.client_nc.uri, false);
users_finger.connect(_root.client_nc);
I you need more info, I can post more of the code on the
forum.
Any help would be really appreciated

I don't see any onStatus events in the code you posted above.
If you're defining the onstatus event outside the function, that's
the problem. When you define the shared object, you also need to
define it's onStatus event handler.
Also, you really should wait for the onStatus event of the
netConnection before you connect your sharedObjects. If you try to
connect the SO before the netConnection is established, the SO will
never connect.

SAPOSCOL not running:Shared Memory not available

Dears,
On my PI 7.1 server when I go to ST06 I get message:
SAPOSCOL not running:Shared Memory not available
Please suggest.
Shivam

few suggestions
FAQs on saposcol - http://www.saptechies.com/os-collector-saposcol/
SAP Note 165188 - saposcol not running on AIX-DB2
SAP Note 548699 - FAQ: OS collector SAPOSCOL
SAP Note 103135 - DB2-z/OS: Installing saposcol manually
Regards
Sekhar

I'm having problems with my memory load

I'm having problems with my memory load, because I have a few photos on my iPhone 5 (32GB) and has been detected that I am using 10GB of photos, and I only have 1,000 photos. Could someone help me?

Hi Fehmi76,
The article linked below details how to go about seeing what apps on your iPhone are using what amounts of space.
See how much storage you've used on your iPhone, iPad, and iPod touch
https://support.apple.com/en-us/HT201656
Regards,
Allen

Problems with device memory withs new apps and upgrades!

Dear all,
I'm having problems with my memory device. I have installed thes apps:
- Blackberr battery watch
- Bejewled
- Google Maps
- Level
- Ispeech translator
- Octopuzzle
- Shazam Encore
- Simcity Deluxe
- The Light flashlight
- Unit converter premium
- Vlingo
- Weather eye
- Whatsapp Messenger
And it says my 128 Mb device memory is full. How can i clean up this issue so I can continue upgrading and make my device a little more organized.
Thanks!

Hey marcoaramini,
Welcome to the forums.
This article should help you with freeing up some memory on your BlackBerry smartphone.
How to Maximize Battery Life and Free Memory on the BlackBerry smartphone
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Solution to the "Disappearing Comments" problem with shared reviews

I've been having repeated problems with users losing their comments on shared reviews, hosted on my webDAV server. After tearing my hair out for days, I wanted to share the simple fix to this issue, plus another tip:
DON'T USE PERIODS OR SPACES IN FILE NAMES. Use hyphens and underscores instead.
Illegal characters seem to gradually corrupt the file to the point where potentially every comment can get overwritten with a blank .xml file, permanently losing all your comments.
My wish to Adobe is that they would put a pop-up warning at the time of saving a file for shared reviews, something to the effect of:
"WARNING! saving a shared file with a space or a period could result in data corruption when shared over network drives or webDAV. Do you want to replace illegal characters with underscores?"
My other tip is this:
If using a webDAV server as I am, be sure to use the IP address rather than the domain name when specifying the location of the server.

With all the issues you describe, I would search for something conflicting with Mountain Lion.
Have you booted into Safe Mode and checked to see if it works correctly there? It will take a while to boot, and it will run a bit slow, so just look for the issues you described above. If they don't appear, you've got something installed that is causing the issues.

Problem with shared column mapping

I have a problem with mapping different fields onto the same column. In most cases Kodo handles it very well but one tough case it does not
Modification references contract N-1 using contract_id field
Contract back references two modifications out of all modification owned by THIS contract (last_modification and executed_modifcation)
when both modifications are not null it works fine since I make sure both fields point to modification owned by the same contract
hovewer when I set one of the fields (executed_modifcation) to null (after it was not null) Kodo attempts to set not only executed_modifcation field to null but contract_id as well. Which obviously not desired
I understand that it is a pretty hard corner case. Do you think you can handle it or it is a dead end?
Attached are my files

Abe,
I fully agree with your analysis. In my case we can use precedence of direct
mappings over reference mapping in null situation.
However as you noted, there are cases when we have only references and so
you can not say which mapping is more important. However since we are
resolving NULL issue here, I am not sure we need to know precedence of
references - not null case should always take precedence. In other words:
priority 1: direct mapping
priority 2: not null reference
priority 3: null reference
Of course all three cases are subject rule of not changing value of shared
column
"Abe White" <[email protected]> wrote in message
news:[email protected]...
I admit that I didn't go through all your metadata, but I do believe that
3.0 final will handle this case. My plan is to implement updates such
that direct field mappings always take precedence over foreign key
mappings.
Let's say column CONTRACT_ID is used by int field contractId and is
also used by field lastModification as part of an FK to a Modification
instance (which I believe is close to your mapping). Because contractId
is a simple field rather than a foreign key, Kodo will give it the final
say on nulling/defaulting the CONTRACT_ID column. So if you null the
lasetModification field, CONTRACT_ID will retain the value of the
contractId field. Any non-null value of the lastModification field will
stilly have to jive with the contractId field, though, or else we'll
throw an exception like we do currently when you try to set 1 column to
multiple values.
I believe this solves the common case of shared
columns between direct mappings and FK mappings. There are other cases
in which multiple FK mappings overlap on certain columns, and this does
not solve nulling problems in those instances. However, I think those
cases are very rare and not worth the effort. Correct me if I'm wrong
and your situation actually is one of sharing columns between multiple
FKs and no primitives after all.

Problem with shared services,, cannot load "assign access control"

i m using 11.1.1.3 version of EPM.
I have configured Essbase with Shared Services.
When I do right click on application on shared services and select "Assign Access Control" , it gives "loading.." .it remains same for hours..
I re configured essbase ,, but problem remained same...
Could you please suggest what I can do assign filters to users.

Have you given maxl a try:
grant filter appname.dbname.filtername to user;
Cheers
John
http://john-goodwin.blogspot.com/

Oracle 8 EE (CD) problem with Java & Memory

i have thi problem. When I run installation from Oracle 8i
Enterprise Edition (Release 8.1.5) just install maybe half of
all database. Some problem with memory (like no free memory in
computer.) But why if I have 64Megs of ram ?!
Some same problems ?
Thanx
null

It should be a problem whith Java on Linux ... The blackdown guys
says that the gc doesn't work "perfectly" on Linux ... If you
look at the process size while the installation, it starts to
grow bigger and bigger, etc ...
Take a look at your swap size, or try the green threads, or
another version of the jvm : I installed 8i whith java v1.1.7v3,
green threads.
Hope this helps.
Lukas Mesani (guest) wrote:
: i have thi problem. When I run installation from Oracle 8i
: Enterprise Edition (Release 8.1.5) just install maybe half of
: all database. Some problem with memory (like no free memory in
: computer.) But why if I have 64Megs of ram ?!
: Some same problems ?
: Thanx
null

Having Problems With Sharing & Permissions in Finder

I am using a Mac Mini (mid-2011) running Lion Server 10.7.4.
I have noticed lately that when I check files the Sharing & Permissions portion using Get Info on my files I find that there are two lines for each user on my compuer. The first set of lines says Read & Write which I actually selected. The second set of lines says Custom. When I check I have the list Read & Write, Read, Custom. When I try to change Custom I cam select new option No Privileges Info. For the other users I am able to delete the extra line once I select No Privileges Info. However even though I have more than one line I cannot delete the extra line for the main user. I will try and delete the extra line for the main user logged in as someone else that has what I have defined as admin privileges (reason I have more than one user).
This really concerns me because this issue is causing problems with me adding or removing files as needed in the terminal. When I try I get this funky error:
Dubious permissions on file (skipping): filename with duplicate entries for a user.
This is happening more and more even though I am not changing the file permissions that I am aware of.
Any help would be appreciated.

Repairing the permissions of a home folder in Lion is a complicated procedure. I don’t know of a simpler one that always works.
Back up all data now. Before proceeding, you must be sure you can restore your system to its present state
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the page that opens.
Drag or copy — do not type — the following line into the Terminal window, then press return:
chmod -R -N ~
The command will take a noticeable amount of time to run. When a new line ending in a dollar sign ($) appears below what you entered, it’s done. You may see a few error messages about an “invalid argument” while the command is running. You can ignore those. If you get an error message with the words “Permission denied,” enter this:
sudo !!
You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up.
Next, boot into Recovery by holding down the key combination command-R at startup. Release the keys when you see a gray screen with a spinning dial.
When the Recovery screen appears, select Utilities ▹ Terminal from the menu bar.
In the Terminal window, enter “resetpassword” (without the quotes) and press return. A Reset Password window opens. You’re not going to reset the password.
Select your boot volume if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select  ▹ Restart from the menu bar.

TR: Problem with free memory

DARTIGUENAVE Antoine wrote:
Dear forte users,
If my first mail about our "free pointer Memory with Forte" was notclear
enough
I try to give details of the circumstances when it occurs :
our forte program performs twice a call to the methode Open_Uni_session
which returns a pointer to Structure ( defined in the wrraped library ).
The first time , an exception is raised after reading the structure,
The free Memory processed before ( or after ) raising the Exc is allright !
The second time, an Exception is raised after reading the structuremakes a
Segmentation access violation Exception ! the Free Memory makes a
segmentation Acces Violation exception !
I am trying to resolve the problem by the following way :
Concerning my problem to free memory for a pointer to structure ,
after return of the wrapped method ,
there is no more problem when I initialise the structure pointed before
processing Free( pointer );
unResultat->ret_type = 0;
unResultat->ret_info =0;
free(unResultat);
raise Exc;
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Forgot to tell.
Before my iphone, i had a Samsung Galaxy Ace.
With my Samsung I had nog problem at the same places.

Problems with sharing

Hi,
I'm Building a Windows 2008 R2 Enterprise server for a schoolproject.
And i have problems with making the shares work.
I've used the share and Storage Managment to share the folders.
But with the testing of the share somethings gone wrong.
I can open the folders and documents but i can't create of modify new data.
My share permissions are Change and Read.
My permissions in the acces controle list are : List folders content, Read and Write.
I've tried the change the settings and sharing over and over again.
But i can't get set in the right way.
I'm Building the server with VMware Workstation 8
So Helpp!!

Please note that this is Directory Services Forum and your request is regarding Files and Folders management.
I would recommend asking them in File Services and Storage forum: http://social.technet.microsoft.com/Forums/en-us/home?forum=winserverfiles&filter=alltypes&sort=lastpostdesc
This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
Get Active Directory User Last Logon
Create an Active Directory test domain similar to the production one
Management of test accounts in an Active Directory production domain - Part I
Management of test accounts in an Active Directory production domain - Part II
Management of test accounts in an Active Directory production domain - Part III
Reset Active Directory user password

Complex query cannot cope with shared memory

Hi All,
SELECT s.sessionid,
s.requestid,
s.locumid,
s.sessiondate,
s.sessionstart,
s.sessionend,
s.status,
decode(type,   '1',   'Surgeries',   '2',   'Surgeries and Visits',   '3',   'Surgeries and On Call',   '4',   'Surgeries, On call and Visits',   '5',   'On Call',   '6',   'Visits',   '0',   'Type not listed',   type)
FROM sessions s,
locumdetails l,
locumrequest lr
WHERE l.locumid = s.locumid
AND lr.locumrequestid = s.requestid;
see error below:
I am presently on 9i. Do i need to increase the share memory size. and where if do or what is the problem. help
ERROR at line 1:
ORA-04031: unable to allocate 4096 bytes of shared memory ("large pool","unknown object","hash-join .
What do I do in such situation please.
cube60Message was edited by:
cube60

Thanks Ranga
Re: strange startup problem
The database in question was set as a shared and not a dedicated server. So, in trying to increase the shared pool size in OEM, it would not shut down because it is running on a shared memory service. So I had to change or add to the TNSnames.ora and .bak under that TNSname changing it to a dedicated server and it took in the new memory increase quite alright.
addedd (server = Dedicated) in code below:
EDIS =
(DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = TCP)(HOST = fulham)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = dedicated)
      (SERVICE_NAME = edis)
)and it was fine
Thanks for the reference.
cube60
Message was edited by:
cube60

SAPOSCOL Problems with Shared Memory

Similar Messages

Maybe you are looking for