Sat. A300 - USB ICH8 Family USB Universal Host Controller is not working

Device: Intel(R) ICH8 Family USB Universal Host Controller - 2830 till 2836 and 283A
Driverversion is: 8.0.0.1008
Driverdate: 15.09.2006
is not working!
Can anybody help me? Where do I find the actual driver?
Thanks in advance.
Chris

The Intel Chipset driver handles USB drivers. You can download it from the Toshiba Support/Drivers Website.
But if you installed a strange USB Device recently (perhaps a USB keyboard/mouse/HDD), its driver may be conflicting. So you would need to remove that driver from Control Panel -> Program Features first, then reinstall the Intel Chipset Driver.

Similar Messages

Intel usb 3,0 extensible host controller driver not working

I have a hp envy sleekbook 6 1100se.
Im facing a problem with the driver of usb 3.0 extensible host controller 0100 microsoft. It says that the device cannot start. gives a CODE 10 error. Im using windows 8. i've tried updating it and uninstalling and reinstalling it but it doesnt help. I've restored the laptop to its factory settings and then for like 10 minutes the usb 3 ports worked fine and so did the driver. but i restarted my pc and again it gave me error code 10. Its also got something to do with the date of the computer. in the events of the driver it said device started in the date 8/28/2012. but after i changed the date it stopped working. but now this fix doesnt work when the second time i reset my computer.
i also know its not a hardware fault because when i plug in my usb in the usb 3 port, the device turns on its light which means that its working. put the computer does not open it or detect the usb drive.
Help please. !

Hi,
Please use the following post:
http://h30434.www3.hp.com/t5/forums/replypage/board-id/General/message-id/76373
Thanks.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

T430S device manager: USB-IF x HCI USB host controller is not working properly

Hi ,
How to change get ride off the exclamatory mark on this device:
Problem:
Device manger Intel WiUSB: USB IF x HCI USB Host Controller always has the exclamartory mark on it.
Device status: This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
Pls help, thanks.

Hey there wche5,
I found some information over on this thread may be beneficial to your situation. This controller enables USB over wireless as part of the Intel (WiDi) Wireless Display function. To obtain a fix you will need to go to the Intel Site, and run the Intel Driver Update Utility. This should identify any Intel drivers you have that are out of date, including the WiDi driver.
Other threads on the forums point directly to this driver by Intel that typically resolves the problem, found on this thread at the end.
I hope this able to assist you in getting a solution to your issue, Thank You wche5!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

How to find the drivers of intel(R) 82801EB USB Universal Host Controller ?

I only find http://binarydb.com/driver/Intel%28R%29-82801EB-USB-Universal-Host-Controller-_-_-24D2-507.html, not find another.
Driver name:
Intel(R) 82801EB USB Universal Host Controller - 24D2
Version:
5.1.2600.2180
Date added:
7-1-2001
Manufacturer:
(Standard USB Host Controller)
Provider:
Microsoft
Update date:
7-1-2001
Device class:
USB
Device GUID:
36FC9E60-C465-11CF-8056-444553540000
Install Id:
PCI\VEN_8086&DEV_24D2&SUBSYS_0C4A8086&REV_02\3&267A616A&0&E8
Inf file name:
usbport.inf
Section name:
UHCI.Dev
Capabilitys:
unknown
Services:
usbuhci
HardwareIDs:
PCI\VEN_8086&DEV_24D2&SUBSYS_0C4A8086&REV_02
PCI\VEN_8086&DEV_24D2&SUBSYS_0C4A8086
PCI\VEN_8086&DEV_24D2&CC_0C0300
PCI\VEN_8086&DEV_24D2&CC_0C03
CompatibleIDs:
PCI\VEN_8086&DEV_24D2&REV_02
PCI\VEN_8086&DEV_24D2
PCI\VEN_8086&CC_0C0300
PCI\VEN_8086&CC_0C03
PCI\VEN_8086
PCI\CC_0C0300
PCI\CC_0C03
Operating system:
Microsoft Windows XP Professional Service Pack 3 (build 2600)
Microsoft Windows XP Professional Service Pack 2 (build 2600)
Microsoft Windows XP Home Edition Service Pack 2 (build 2600)
Occurence:
998 users

This component is supported by Microsoft inbox INF USBPORT.INF on Windows7, there should be no need for "drivers" for this [very old generation ICH5] component?
Only old OS like WinXP etc would need to have non-inbox INF installed e.g. 82801EB USB Universal Host Controller - 24D2
https://downloadcenter.intel.com/download/14713/Chipset-INF-Update-Utility-for-848-865-875-910-915-925-Chipset-Based-Intel-Desktop-Boards
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

HT1338 I have macbook without a firewire port, I have usb 2.0 port, now my os is not working I can not get through apple logo loading , I can not enter safe mode, I can only enter one user mode, how can I backup my data, I have very important data in my h

I have macbook without a firewire port, I have usb 2.0 port, now my os is not working I can not get through apple logo loading , I can not enter safe mode, I can only enter one user mode, how can I backup my data, I have very important data in my hdd

Here is what worked for me:
My usb hub, being usb2, was too fast. I moved the wire to a usb port directory on my pc. That is a usb1 port which is slow enough to run your snyc.

Host command is not working on linux

Hi
I m using linux for application server n windows for client. I need to create folder from client machine by cliking a button of forms10g runtime.HOST command is not working which was working fine in windows.
Any help is appriciateable.
kazi mokarem

Hi
I had the same issue on linux a few weeks back. What tuned out was, when you install the Oracle app svr it does not include the system paths by default.
The path where mkdir is located may not be visible to the app.
Try to hardcode the path for mkdir as /bin/mkdir .... and seee if that works.
If the above statement works then add that path in the paths variable in default.env file located in $ORACLE_HOME/forms/server directory
HTH
Arvind

The USB ethernet adapter for the macbook air is not working. Cable unplugged. How can I fix this for the recent patch 10.7.2?

I have recently purchased an ethernet usb adapter for the MBA and after a month it is not working. Says cable unplugged.
Now I have tried it with 2 other connections on other computers that are working and still no response. Many reviews or fixes online mention something with a 10.5.5 patch that seems quite outdated and do not work. Anyone figure out how to fix this or do I have a broken adapter?

I've used Apple's adaptor on a mini MBA without a problem.

HT4623 on upgrading iPhone 4 to ios 6 using itunes it returned an unknown error then froze completely. It has the iTunes and USB connector on the screen. Reset is not working, I get the same frozen screen.

On upgrading iPhone 4 to ios 6 using iTunes, it returned an unknown error then froze completely with the iTunes icon and USB connector on the screen. Reset didn't work. iTunes doesn't recognize the devise anymore.

if your computer is not recognizing it, try using a different USB port or different usb cable. if that doesnt work you will need to uninstall and reinstall itunes.

All I can see on my Ipod is the itunes app plugged into the usb. I have reset it and still not working

I am getting a black screen on my ipod touch. I plug it into the ihome or the computer and all it shows it the round itunes and the usb plug in. I have tried to reset it by pushing the home button with the on/off button and it will show the apple for just a split second and then go back to the itune/usb screen. What can I do to fix this.

Connect the iOS device to your computer and restore via iTunes. Place the iOS device in Recovery Mode if necessary to allow the restore.
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software

Ricoh PCIe SDXC/MMC Host Controller does not detect SD cards

Hi,
My Lenovo Thinkpad X230 has an integrated 4-in-1 SD card reader (SD/SDHC/SDXCMMC), but it does not detect any card I insert. The two cards I have are working correctly under my sister's MacBook. My kernel version is 3.6.10. Here's the output of a few commands :
lspci -k
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
Subsystem: Lenovo Device 21fa
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
Subsystem: Lenovo Device 21fa
Kernel driver in use: i915
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: xhci_hcd
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: mei
00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04)
Subsystem: Lenovo Device 21f3
Kernel driver in use: e1000e
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: ehci_hcd
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 (rev c4)
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge: Intel Corporation QM77 Express Chipset LPC Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: i801_smbus
02:00.0 System peripheral: Ricoh Co Ltd PCIe SDXC/MMC Host Controller (rev 07)
Subsystem: Lenovo Device 21fa
Kernel driver in use: sdhci-pci
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device 8195
Kernel driver in use: rtl8192ce
lsmod | grep sd
sd_mod 29560 4
scsi_mod 133434 2 libata,sd_mod
sdhci_pci 10834 0
sdhci 23695 1 sdhci_pci
mmc_core 82791 2 sdhci,sdhci_pci
Nothing new happens if I type dmesg | tail after inserting a card.
I didn't find any solution after searching on Google, but it seems there are a few other people experiencing the same problem as me. I haven't actively tried anything yet.
I don't have much experience when it gets to this kind of things, so I hope there are some of you who can help me.
Thank you!
Last edited by Fayden (2012-12-22 05:13:09)

In case someone else has the same problem, there's actually a package in the AUR that fixes the problem : https://aur.archlinux.org/packages/ricoh-e823-fix/
Install it and enables it with systemd and it should work correctly!

Any ideas why the second HOST call does not work???

Hi Folks.
I have written the following code which works fine in all but one respect.
The code creates a zip file on a server (Accessed over a network) hence the full windows network path name.
The call to host on the server works in terms of running the zipinvoices.bat file and the zip file is generated on the server in the correct location.
The prigram unit also generates the correctly formatted mailinvoices.bat file. However, the second call to HOST does not run/execute the mailinvoices.bat file. If I go to the server and run the mailinvoices.bat file directly, it runs perfectly and emails the file to me, no problemo.
Why does the second call to HOST from the client machine not run?
Any clues anyone???
Cheers
Simon Gadd
PROCEDURE send_email_invoices_pu_p (p_organisation IN VARCHAR2) IS
v_processing_cycle          CHAR(4);
     v_alert_but                              NUMBER;
     v_error_num                              NUMBER;
     v_sent_status                     NUMBER(1);
v_stage                                        NUMBER(1);
v_year                                        VARCHAR2(4);
v_month                                        VARCHAR2(9);
v_folder_name                         VARCHAR2(25); -- Name of the file which holds the 'Printed' invoices in the receivables folder. v_organisation                    VARCHAR2(50);
v_password                              VARCHAR2(25);
v_organisation                    VARCHAR2(25);
     v_host_command                    VARCHAR2(100);
v_from_name                              VARCHAR2(100);
v_to_name                                   VARCHAR2(100);
v_subject                                   VARCHAR2(100);
v_error_txt                              VARCHAR2(200);
v_file                                        VARCHAR2(200);
v_message                                   VARCHAR2(500);
     v_line_buffer                         VARCHAR2(5000);
v_working                                   BOOLEAN := TRUE;
v_zipinvoices_bat               TEXT_IO.FILE_TYPE;
     v_mailinvoices_bat          TEXT_IO.FILE_TYPE;
     CURSOR c_sent_status IS
          SELECT sent
          FROM INVOICE_EMAIL
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
     CURSOR c_select_folder IS
          SELECT folder
          FROM INVOICE_EMAIL
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
CURSOR c_select_email_elements IS
SELECT      send_to,
                    send_from
FROM INVOICE_EMAIL
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
BEGIN
v_organisation := p_organisation;
-- Check to see if the invoices have already been e-mailed for this Procssing Cycle. If they have,
-- then warn the user of this and get them to confirm that they wish to proceed and e-mail them again.
-- The batch e-mail process will re-zip the invoices (ignoring a pre existing .zip file) and overwrite
-- the existing zip file if it exists or generate it if it does not exist.
     OPEN c_sent_status;
          FETCH c_sent_status INTO v_sent_status;
     CLOSE c_sent_status;
     IF v_sent_status = 1 THEN
          v_alert_but := SHOW_ALERT('SEND_AGAIN_ALRT');
               IF v_alert_but = ALERT_BUTTON2 THEN RAISE FORM_TRIGGER_FAILURE;
                    ELSE NULL;
               END IF;
     END IF;
:CONTROL.WORKING := 'Started Zipping invoices for '||INITCAP(v_organisation)||'.'||CHR(10)||'Please wait..';
SYNCHRONIZE;
-- The following code opens the zipinvoices.bat file which resides in the root folder \\Ebony\c$\FCSS\DB_SCRIPTS\ and modifies it ready to
-- zip up the invoices in the relevant organisation's invoice folder for the current processing cycle.
v_processing_cycle := GET_CURRENT_TRAFFIC_PERIOD;
v_month := RTRIM(INITCAP(TO_CHAR(TO_DATE(v_processing_cycle, 'MMYY'), 'MONTH')));
v_year := (TO_CHAR(TO_DATE(v_processing_cycle, 'MMYY'), 'YYYY'));
     OPEN c_select_folder;
     FETCH c_select_folder INTO v_folder_name;
     CLOSE c_select_folder;
KILL_OLD_ZIP_PU_P('del \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\invoices.zip');
SELECT zip_password
INTO v_password
FROM INVOICE_EMAIL
WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
v_zipinvoices_bat := TEXT_IO.FOPEN('\\Ebony\c$\FCSS\DB_SCRIPTS\zipinvoices.bat', 'w');
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
v_line_buffer := 'wzzip -s'||v_password||' -x*.zip -ybc \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\invoices \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\*.*';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
v_line_buffer := 'exit';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
TEXT_IO.FCLOSE (v_zipinvoices_bat);
-- The following code executes the freshly edited \\Ebony\c$\FCSS\DB_SCRIPTS\zipinvoices.bat file to produce the zipped invoices file
-- ready to be e-mailed out to the address specified in the INVOICE_EMAIL table for the relevant organisation.
v_host_command := '\\Ebony\c$\FCSS\DB_SCRIPTS\zipinvoices.bat';
v_stage := 1;
HOST (v_host_command, NO_SCREEN);
IF NOT Form_Success THEN
     IF v_stage = 1 THEN
     :CONTROL.WORKING := 'Error -- The .zip file for '||INITCAP(v_organisation)||' was not produced.';
          SYNCHRONIZE;
     ELSIF v_STAGE = 2 THEN
     :CONTROL.WORKING := 'Error -- The zipped invoices file for '||INITCAP(v_organisation)||' was not emailed.';
          SYNCHRONIZE;
          END IF;
ELSE NULL;
END IF;
:CONTROL.WORKING := 'All invoices for '||INITCAP(v_organisation)||' successfully zipped.'||CHR(10)||'Attempting to send via e-mail.'||CHR(10)||'Please wait..';
SYNCHRONIZE;
-- The following code e-mails the freshly created .zip file for the relevant organisation and e-mails it to the
-- recipient specified in the relevant row in the INVOICE_EMAIL programme along with from address, subject and
-- message if specified.
OPEN c_select_email_elements;
FETCH c_select_email_elements INTO
v_to_name,
v_from_name;
CLOSE c_select_email_elements;
v_stage := 2;
v_mailinvoices_bat := TEXT_IO.FOPEN('\\Ebony\c$\FCSS\DB_SCRIPTS\mailinvoices.bat', 'w');
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
v_line_buffer := 'clemail -quiet -smtpserver mailhost.0800dial.com -smtpport 25 -to '||v_to_name||' -from '||v_from_name||' -subject "'||v_month||' '||v_year||' Roaming Traffic Invoices from United Clearing Ltd" -bodyfile \\Ebony\c$\FCSS\DB_SCRIPTS\invoice_body.txt -attach \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\invoices.zip';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
v_line_buffer := 'exit';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
TEXT_IO.FCLOSE (v_mailinvoices_bat);
v_host_command := '\\Ebony\c$\FCSS\DB_SCRIPTS\mailinvoices.bat';
HOST (v_host_command, NO_SCREEN);
IF NOT Form_Success THEN
     IF v_stage = 1 THEN
     :CONTROL.WORKING := 'Error -- The .zip file for '||INITCAP(v_organisation)||' was not produced.';
          SYNCHRONIZE;
     ELSIF v_STAGE = 2 THEN
     :CONTROL.WORKING := 'Error -- The zipped invoices file for '||INITCAP(v_organisation)||' was not emailed.';
          SYNCHRONIZE;
          END IF;
ELSE NULL;
END IF;
UPDATE INVOICE_EMAIL
     SET sent = 1
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
COMMIT;
GO_BLOCK ('INVOICE_EMAIL');
EXECUTE_QUERY;
:CONTROL.WORKING := 'Please press a button on the left to e-mail invoices to the organisations listed.';
SYNCHRONIZE;
EXCEPTION
     WHEN OTHERS THEN
          v_error_num := SQLCODE;
          v_error_txt := SUBSTR(SQLERRM, 1, 200);
          MESSAGE('The error was: '||v_error_txt||' and the code was: '||v_error_num);
          RAISE FORM_TRIGGER_FAILURE;
END;

As a suggestion I'd put the Text_io segments into their own begin - exception - end sub-blocks within the main code. This way if Text_io does raise an exception you can catch it earlier as it may be able to recover - That is if it is a text_io exception.
Other than that you;ll have to step through in Debug.

Hp pevilion :catylist host program is not working

hi i am using a hp peavilion 15 e015tx with windows 8
recently the radeon host program has stopped working....
i have tried re installing the driver using hp recovory manager but it is of no use ...please help me

Hello susaanth,
Welcome to the HP Forums.
I see that recently the radeon host program has stopped working correctly on your Notebook for the graphics. I will try to help you with this.
As trying to recover the drivers with the recovery manager seems to have fail (if you could provide details on this it may help), also I would like you to try updating the drivers. Here is a link to the update: AMD High-Definition (HD) Graphics Driver.
Please let me know if this was able to help you. Thank you for posting on the HP Forums.
I worked on behalf of HP.

My BC hosted sites are not working

My sites hosted in BC UK are not working and I cannot update a site. Is the system down at moment.

Hi jasperimage66,
There was a short emergency maintenance performed this morning which affected the availability of sites hosted on the European Union data center, as per our status page: http://status.businesscatalyst.com/.
I can confirm this has since been completed and that your site will now be available.

Intel (R) Family USB Universal Host Controller 2934

Windows has stopped its function because a problem has occurred, how to solve this problem ?

A Microsoft support engineer responded here.
Error Code 52 - USB ports not recognizing connected USB devices stating that "Windows cannot verify ...
That's for Windows 7. If you reply, tell us which computer you have and which Windows.
-Jerry

CP2102 USB to UART Bridge Controller installation not working

I have been working with Silicon Labs and Davis Instruments to try to get this driver installed on my iMac without any success. The driver was working on 10.4.11, but after I upgraded to 10.6.2 it is no longer recognized and does not show up in /dev, i.e. no cu.CP2102... or tty.CP2102... . I went to the Silicon Labs web site and downloaded the VCP driver kit that is used to talk to the Davis device (https://www.silabs.com/Support%20Documents/Software/MacOSX_VCPDriver.zip), performed the installation, and restarted.
I looked at System Preferences, then at Network Preferences. The <CP2102 USB to UART Bridge Controller> shows up as a grayed out Modem with Inactive Status. Clicking on the Advanced button, it shows the CP2102 as an Apple Modem. Under the WINS tab, it lists the CP2102's NetBIOS Name as IMAC-C7DFF1 and indicates that name is currently being used (possibly by another USB to UART adaptor I use to talk to an old Garmin, i.e. usbserial-FTCUSRHZ, and showing the same NetBIOS Name). Not sure if this is the reason that the CP2102 is not being seen.
I searched Console, Kernel, Install, and System logs for CP2102, among other things. I did not see any problems in those logs over the installation timeframe. I did notice that the CP2102 gets turned off after 10 seconds of no activity several times in the past in Kernel log, but not as a result of this set of installs. I scanned the various logs over the half hour of the install process, but did not see anything else of interest.
I opened System Profile and clicked on the USB selection. I expanded each of the USB entries and found the one that shows the CP2102. It shows
CP2102 USB to UART Bridge Controller:
Product ID: 0xea61
Vendor ID: 0x10c4 (Silicon Laboratories, Inc.)
Version: 1.00
Serial Number: 1205096541
Speed: Up to 12 Mb/sec
Manufacturer: Silicon Labs
Location ID: 0xfd110000
Current Available (mA): 500
Current Required (mA): 100
So, the CP2102 is being recognized, but the driver (cu. and tty.) cannot be found (or possibly is not installed).
I tied more things:
1. Performed a Mac reset of SMC and PRAM, with no joy.
2. Reinstalled Snow Leopard. Reinstalled the Si Labs driver package, and restarted. The CP2102 driver still does not show in the /dev directory (either as cu.CP2102... or tty.CP2102...).
3. I looked in /System/Library/Extensions and found the SI Labs kernel extension SiLabsUSBDriver.kext. I decided I should perform an operation I read about, i.e. touch /System/Library/Extensions, and reboot. Still no joy.
4. The System Profile still shows the same CP2102 entry.
Silicon Labs indicated that some how, based on System Profile information, the Product ID was changed from 0xEA60 to 0xEA61, thus pointing to the USBXpress driver and not the VCP driver. Silicon Labs only has Windows PC tools to fix the Product ID problem, so they cannot help.
Finally, I did some additional investigation to try to obtain more information. I moved my USB items around and looked in /dev. Here is what I observed (last boot of my Mac was 12:31 PM on 12/22 and the moving things around occurred at about 10:00 AM on 12/27):
crw-rw-rw- 1 wheel 18, 3 Dec 22 12:31 cu.Bluetooth-Modem
crw-rw-rw- 1 wheel 18, 1 Dec 22 12:31 cu.Bluetooth-PDA-Sync
crw-rw-rw- 1 wheel 18, 17 Dec 27 10:00 cu.usbserial-FTCUSRHZ
crw-rw-rw- 1 tty 15, 1 Dec 27 10:04 ptmx
crw-rw-rw- 1 wheel 9, 0 Dec 27 10:04 random
crw-rw-rw- 1 wheel 18, 2 Dec 22 12:31 tty.Bluetooth-Modem
crw-rw-rw- 1 wheel 18, 0 Dec 22 12:31 tty.Bluetooth-PDA-Sync
crw-rw-rw- 1 wheel 18, 16 Dec 27 10:00 tty.usbserial-FTCUSRHZ
crw--w---- 1 tty 16, 0 Dec 27 10:04 ttys000
There are a couple of devices that I cannot identify: ptmx, random, and ttys000. ttys000 is certainly out of place and I am wondering if it is the CP 2102 device. Its permissions certainly seem strange too (i.e. crw--w----) as well as its owner and group (tty and 16). In addition, the ptmx owner and group seem strange (tty and 15) as well. Just about everything else is owned by wheel or operator.
Looking at /etc/group, there is no group = 15 and the group name for 16 is "group." Looking at /etc/passwd, the owner tty (whose owner number is 4) really points to _uucp (Unix to Unix copy protocol). All of this information seems a little strange.
I would certainly like to get this driver installed properly, so I can talk to Davis device. Any help would be greatly appreciated.

I have been told by Davis that the Product ID (PID) for the Mac is 0xEA60 and the PID for Windows is 0xEA61. To solve the problem on the Mac only, you apparently have to get a PC and connect to the Vantage Pro console with the PC. Then you have to perform the following steps to reprogram the PID using the PC using Windows:
1. Install the USBXpress driver on the PC running Windows.
2. Then run AN144SW "CP210xSetIDs.exe" with "CP210xManufacturing.dll" and change the PID from 0xEA61 to 0xEA60.
3. Install the VCP driver on the Mac
4. Now, the CP210x device is ready to be used on your Mac with the VCP driver.
USBXpress: http://www.silabs.com/products/mcu/Pages/USBXpress.aspx
AN144SW: AN144SW
http://www.silabs.com/Support Documents/Software/an144sw.zip
The VCP driver is available for Mac OSX here:
http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
If you run Parallels or VMware or another virtual system to run WeatherLink on Windows, in addition to running WeatherLink on the Mac, you need to perform the following additional step after Step 1 above (note that you do not need a PC, just use the Windows on the virtual machine for Steps 1-4 above and Step 1a below):
1a. Install the VCP driver on the virtual machine for Windows.
The VCP driver is available for Windows here:
http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
Now, the CP2102 will re-enumerate on Windows under the virtual machine. You will see that Windows is now recognizing it as a Virtual COM port device instead of a USBXpress device. In addition, you should see the CP2102 (with PID = 0xEA60) on your Mac.
Hope this information helps and solves the problem for all of us.

Sat. A300 - USB ICH8 Family USB Universal Host Controller is not working

Similar Messages

Maybe you are looking for