SATA 3 and 4 do not appear to work

Hi,
I just purchased a new WD 320GB HDD to accompany my other 2 WD HDD but for some reason SATA slots 3 and 4 do not appear to work or there must be some way you have to enable them. It is definitely not the new HDD as it works in the other two SATA slots. Any help would be appreciated in getting this new HDD installed.
Regards

Okay reading the manual is a good thing I have discovered. It was 2 and 4 that werent working but it was because of a BIOS setting. I have now changed integrated peripherals to SATA only and all 3 HDD now work fine. My problem now is that the 2 CD/DVD drives that I have are now invisible. Does SATA only turn off the IDE function altogether? Any solution greatly appreciated.
Regards

Similar Messages

  • AO and AI do not appear to work with the M&A Explorer. What could be wrong?

    Preliminaries... MAX v3.1.0.3201
    Board PCI-MIO-16E-1 (manufactured late 2002)
    I have a relatively unused board that a collegue lended to me. After plugging the board into my PC, the AO and AI don't currently work with the Measurement and Automation Explorer (MAX) Test Panel. Specifically, AI all read -10V (even when pulled to AIGnd) and AI all produce -0.40V, regardless of the commanded output. The device passes self test, but the device fails to perform a self-calibration (error -200545), even if all external connections are removed. Is this board defunct? Does it need to be recalibrated? A recalibration seems unlikely to have any effect given that none of the analog i/o values change with manipulation.
    As a side note, the digital output functions do work.
    Thank you for any advice.
    Steve

    Thanks for the input. I either missed the web-based self-test or assumed it was the same as the one included with MAX.
    The self calibration, as I previously mentioned, failed with the board disconnected from any cables/inputs. All my previous testing (with the MAX test panels) failed, regardless of using traditional or DAQmx control.
    After running the web-based self test, the results are below:
    Summary -- Test Results Summary
    2/8/2005, 7:18:02 AM, Device 1
    PASS: Detection -- Device Detection and Resource
    PASS: Single Pulse -- Single Shot Pulse Width Verification
    PASS: Continuous Pulse Train -- Buffered Pulse Width Verification
    ABORTED: Calibration -- Analog Input Calibration
    FAIL: ADC, PGIA -- Analog to Digital Converter and Programmable Amplifier
    PASS: Scan Clocks I -- Buffered Analog Input
    PASS: Scan Clocks II -- Sampling Frequency and Channel Count
    ABORTED: ADC Calibration -- Analog Input Calibration
    FAIL: Calibration -- Analog Input Calibration
    FAIL: Unstrobed Analog Output -- Digital to Analog Converter
    PASS: Output Clocks I -- Analog Output Buffer
    PASS: Output Clocks II -- Update Clock Frequency
    FAIL: Buffered Analog Output -- Waveform Output Verification
    PASS: Digital Lines -- Read/Write Verification
    PASS: Digital Ports -- Read/Write Verification
    Device 1 did not pass all tests.
    National Instruments E Series Device Diagnostics is complete.
    Submitting Test Results To National Instruments: Please Wait. . .
    Submitting Test Results To National Instruments: FAIL
    I'd post the rest, but it's just message after message of tests failing.
    The device won't self calibrate, so I had to abort after a few retries.
    It's interesting that the web-based self test is so much more advanced than the MAX self-test, which the board passed. I assume that NI doesn't have a replace-for-free program, so I'll have to return this to my collegue (with the bad news), and find one on ebay or the like.
    Steve

  • Hi all, I upgraded my MBP to Lion , but on the screen where i need to type my password, click  on my photo and it does not appear the place for me to type my password and it stay stuck there. Can anyone solve this problem for me?

    Hi all, I upgraded my MBP to Lion , but on the screen where i need to type my password, click  on my photo and it does not appear the place for me to type my password and it stay stuck there. Can anyone solve this problem for me?

    Reboot the machine holding Command and r keys down, you'll boot into Lion Recovery Partition
    In there will be Disk Utility, use that to select your Lion OS X Partition and Repair Permissions.
    After that is done reboot the machine and see if you can log in.
    If not repeat the above steps to get into Lion Recovery, get online and reinstall Lion again, it will overwrite the installed version and hopefully after that it wil work.
    Reboot and try again.
    If not follow my steps to create a Snow Leopard Data Recovery drive, then option boot from it and grab a copy of your files off the machine.
    Then reinstall all your programs onto the external drive like setting up a new machine, then use Disk Utility to erase the entire internal boot drive (select the drive media on the far left, not the partiton slightly indented) format Option: GUID , 1 partition OS X Extended and then use Carbon Copy Cloner to clone the external to the newly formatted internal drive. Once that is finished reboot and disconnect the external drive.
    Once you go that, boot into Snow Leopard and update to 10.6.8, use the AppStore and option click on Purchases and download Lion again and install.
    Lots of work, but there is no Lion disks.
    https://discussions.apple.com/message/16276201#16276201

  • HT201240 This process does not appear to work for me.  I'm running 10.8.3.  I created a new user for a guest staying with me.  They have gone now and I am attempting to either change the password or delete the user.  It won't allow me to choose the user I

    This process does not appear to work for me.  I'm running 10.8.3.  I created a new user for a guest staying with me.  They have gone now and I am attempting to either change the password or delete the user.  It won't allow me to choose the user I created.  I am logged in as myself and it states that I am an "Admin".  The user I'm attempting to change is listed as a "standard" user and there is a white checkmark inside an orange circular background on the user pic in the list of users. 
    Can someone help me?  I am having a hard time believing that OSx will allow me to create users and allow them use of my computer and it's drives, yet it will not allow me to change the password so I can monitor what they might have been doing while logged on?  What if this were my child?  This guest left under sketchy circumstances, and I'd really like to be able to ensure they were not using my computer to do illegal things or to have illegal communications.
    Any help would be appreciated.  (It's odd that it was so simple to "create" a user and set a password for them.......but it's complicated or a little known process to reverse.
    Thanks.

    Here are two screen shots to show you what I am seeing.  The first screen shot shows it allowing me to select (highlighted in blue) my admin user (which is what I am locced in as).  The second screen shot shows it allowing me to select the "Guest" user (highlighted in blue).  However when I click on the user "Orion" nothing happens.  It will not change to highlight that user.

  • TS4425 when trying to access photo stream on Apple TV, I am getting the error message terms and conditions have changed, but when I go into iCloud on my Mac the new terms and conditions are not appearing - How can I manually agree to them ?

    When trying to access photo stream on Apple TV, I am getting the error message terms and conditions have changed, but when I go into iCloud on my Mac the new terms and conditions are not appearing - How can I manually agree to them ?

    Welcome to the Apple Community.
    The following article(s) may help you.
    Photo Stream ToU's

  • My ipod touch has a permanent image of the end of a USB cable with an arrow pointing to an icon of ITunes. I can't reset, and ipod does not appear on itunes when I plug it into the computer.  This happened after I agreed to a failed software update.

    My ipod touch has a permanent image of the end of a USB cable with an arrow pointing to an icon of ITunes. I can't reset using the two button method, and ipod does not appear on itunes when I plug it into the computer - and nothing else happens either.  This happened after I agreed to a software update which failed.  How can I get it going again?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • I am running IE 11 on Windows 7 Home Premium 64 Bit Service Pack 1. When I attempt to install Flash Player, it goes through all of the steps, tells me the player is installed, and welcomes me. I cannot open the player and it does not appear in the Start M

    I am running IE 11 on Windows 7 Home Premium 64 Bit Service Pack 1. When I attempt to install Flash Player, it goes through all of the steps, tells me the player is installed, and welcomes me. I cannot open the player and it does not appear in the Start Menu, Task Manager, System Tray, or anywhere else. When I try to open a file, the site tells me Flash player is not installed. I have even downloaded it to a separate folder and ran the install with IE shut down completely. And Shockwave in ENABLED but in 32 bit .I have been trying to get this to work for about 3 weeks now.  HELP!!!

    Flash Player is a browser add-on, not an executable program.
    If you need to open a local SWF file you will need the standalone player (Projector) from http://www.adobe.com/support/flashplayer/downloads.html
    Note that the download is the player, not an installer, so you will need to make the file association manually.

  • I upgraded to iTunes 11.0. My iPod Nano 4th Version will sync, but music and playlists will not appear to manage and add more songs. Is there a fix?

    I upgraded to iTunes 11.0. My iPod Nano 4th Version will sync, but music and playlists will not appear to manage and add more songs. Is there a fix?

    If I go from 'Devices' to Summary and then Music, I only get one option-Sync Music,There is a box on this page but the options within it are grayed out. If I tick the Sync Music option I get this message-
    'Are you sure you want to remove existing music,films,ect, from this ipod and sync with this itunes library?
    'Music synced to (my ipods name) from other itunes libraries will be removed and items will be synced from this itunes library' I have only ever used itunes on this PC and the 'Manually manage music and videos' is ticked but
    that must be a default setting as I haven't ticked it.

  • The Shared option is not appearing in my list. I am turning it off and the back on and it is not appearing. Please HELP

    Been trying for anout 1 hour now and no joy. I am trying to transfer all my music and apps etc from my old laptop to my new and read home sharing would be the easiest. However I am switching home sharing on and it is not appearing on the list.
    Help would be appreciated.
    Thanks

    Device not detected in iTunes for Windows

  • Ipad takes photo every time I close the cover of its case. When I close the cover - it really does take a picture and saves a photo. Luckly, it make a click, and pictures are seen in the photo album, and it does not appear to be forwarding.

    When I close the cover - it really does take a picture and saves a photo. Luckly, it make a click, and pictures are seen in the photo album, and it does not appear to be forwarding. It is just gobbling memory and annoying as I can only delete these pictures one at a time.

    It seems to take a picture of the counter top = I do not see the keyboard.
    I am wondering ....It may be a kids game app that takes pictures of the screen or out the back camera. I am starting to think it may just be a sound effect when placing the iPad on its screen. So many things that may be unrelated but coincedental. It started in May (the sound) and so did the multiple pictures - starting to think they are not related.
    Thanks for the quick tip on deleting multiple pictures.

  • TS1369 iPhone does not appear in iTunes and also does not appear as a disk drive in My Computer (Windows XP)

    iPod does not appear in iTunes and also does not appear as a disk drive in My Computer (Windows XP)

    iPod or iPhone?
    iPhone and iPod Touch will never show as a disk drive.
    If it's an iPhone, this might help:  iOS device not detected in Windows

  • After reinstallation of Outlook 2010 on my Laptop, Contacts and Calendar did not appeared while they are exist in my iphone 5 by using icloud. What I should do to get Contacts and Calendars in sync with iphone 5? Thank you.

    After reinstallation of Outlook 2010 on my Laptop, Contacts and Calendar did not appeared while they are exist in my iphone 5 by using icloud. What I should do to get Contacts and Calendars in sync with iphone 5?
    Thank you.

    So you have business contacts that were lost... do you not have these on a Database in some shape or form? Sounds like you need to invest in a RAID1 backup setup for your computer so you dont have this issue in the future.
    As for repairing your problem, sounds like you are going to need to start from scratch at this point or if the data is still on your phone look into a program that can take the information from the phone onto iTunes.

  • I was running Foxfire 3.6.9 and wanted to use FTP Program add-on and it did not appear to load but appeared but then would be installed but not run or appear under tools. So I deleted Foxfire 3.6.9 and down loaded to 3.5.9 so it could get FTP and it is do

    I was running Foxfire 3.6.9 and wanted to use FTP Program add-on and it did not appear to load but appeared but then would be installed but not run or appear under tools. So I deleted Foxfire 3.6.9 and down loaded to 3.5.9 so it could get FTP and it is doing the same could not install. Even after I registered my copy. The last time I used this program it showed up under tools and worked great. any suggestions on whats going on and how I can get around this?.by ralphd3g

    Delete the files extensions.* (extensions.rdf, extensions.cache, extensions.ini) and compatibility.ini in the Firefox [[Profiles|profile folder]] to reset the extensions registry.
    See "Corrupt extension files": http://kb.mozillazine.org/Unable_to_install_themes_or_extensions
    If you see disabled extensions that are not compatible on the next start in "Tools > Add-ons > Extensions" then click the "Find Updates" button to do a compatibility check.

  • Street 4 and street 5 not appearing in XK01

    street 4 and street 5 not appearing in XK01
    Screen is 301.
    We are not able to view street 4 and street 5 in XK01.
    Thanks
    Tirth

    Hi,
    Do not remember the transaction code, but in customizing there is option to change the layout of the field groups. (Fields within the group remain at the same sequence, but you can change the place of field status group.)
    Go to SPRO > Financial Accounting > AR/AP > Vendor >Master Data
    You will find there.
    Regards,
    SDNer

  • My pics and videos do not appear in the video browser?

    my pics and videos do not appear in the video browser? How do I get it back. I may have denied IMovie access to my pics and videos when opening the app for the first time.

    I have the same issue (iPad 3, iOS 6).  I have tried to:
    -erase all projects on the iMovie
    -reset the iPad
    -uninstall iMovie and reinstall it
    None of these three things worked and I am at lost in terms of what else can be done.
    All that happens when I start a new project is that under "videos" there is a big black box (empty videos).  Same thing for pictures.  When I press the camera button to insert a video from the camera, this works no problem.  However, I used to be able to insert videos/pictures from my Camera Roll.

Maybe you are looking for