SATA Drive not found and other stuff.

Allright.
I have had all kinds of problems setting up this new system that includes the Neo2 plat, amd 64 3500+ WD Raptor and a seagate 80gb sata.
After reading the quide I found in here I finally got to see my primary sata and finally installed Windows on it. Now my issue is, it doesnt see my second sata drive. I dont know why. Im going to try to update the bios and see if this helps but im going nuts over here. I have them connected on sata 3/4 with 3 being my primary. If anyone can help i would appreciate it. If you need any additional info let me know and ill post it. Thx.

Allright I finally got to see the other drive(changed the power connections around a little bit and now its there) however when i got into standard cmos it doesnt show me either drive there. At least I got the second one to come up so Im good to go right now but kinda strange that the drives dont appear in bios dont ya think?

Similar Messages

Network controller& USB controller driver not found and wifi not working

hello I Purchased HP 15-ac025TX (M9V00PA) Notebook laptop . i have installed all driver from HP site here is the link  http://support.hp.com/in-en/drivers/selfservice/HP-15-Notebook-PC-series/7771404/model/8326084#Z7_3054ICK0KGTE30AQO5O3KA30R1  but still netwok controller driver not found also wifi not working i installed blutooth drivers too . I am using window 7 sp1 (32 bit) For network controller device ID is PCI\VEN_14E4&DEV_4365&SUBSYS_804A103C&REV_01 secondly univeral serial bus driver(usb) controller not found i installed all drivers from above link also update windows but still no solution hardware id of usb controller is PCI\VEN_8086&DEV_9CB1@SUBSYS_80C2103C&REV_03  and last i am unable to download AMD/Intel Switchable High-Definition (HD) Graphics Driver. the download link not working KINDLY RESOLVE THE ISSUE THANK YOU

Update: While the driver I knew would work has not shown up yet, I did some detective work and explored some other broadcom wireless card driver folders from some HP links, and I found one that should work for you. While it says it is for HP desktop PC's, they put the exact same wireless card form factor in a desktop PC that they do in a notebook PC. I see no reason why this driver would not work, since the setup information file contains the same hardware ID that you posted. Here is a partial copy and paste of the driver setup information file and you can see the hardware ID you posted is supported by this driver.  x86 - Win7
[BROADCOM.NTx86.6.1]
    %BCM430N_DeviceDesc% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_2230103C
    %BCM430N_DeviceDesc% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_22D3103C
    %BCM430N_DeviceDesc_HPY% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_2232103C
    %BCM430N_DeviceDesc_HPY% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_22D4103C
    %BCM430N_DeviceDesc_HPY% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_804A103C http://h20566.www2.hp.com/hpsc/swd/public/detail?swItemId=cp_149257_1

Org.flexunit.listeners.UIListener not found, and other problems

I have a basic setup of FlexUnit that comes with the latest FlashBulider. I import a bunch of SWC's in my project and try to follow instructions from here:
http://docs.flexunit.org/index.php?title=Setting_up_a_FlexUnit_4_Project
I got an error saying defintion of UIListener could not be found.
Then I checked the AS docs here: http://docs.flexunit.org/asdocs/index.html
And found out there is no UIListener class at all
So I realized that core.addListener takes IRunListener, and change the code to this:
core.addListener(IRunListener(uiListener));
Sadly, when run. there was a runtime error with this line:
<flexui:TestRunnerBase id="uiListener" width="100%" height="100%" x="0" y="0" />
Saying TestRunnerBase does not implement the IRunListener intarface,

The UIListener is not in the core project, it is in the UIListener project, so unless you have that one as well, you will not have the UIListener.
My guess though is that it is a TestRunnerBase issue. TestRunnerBase isn't something we wrote for FlexUnit 4. It is an adaption of a FlexUnit 1 concept to give people a familiar environment as a default test runner. The goal is to eventually write a new one for FlexUnit 4 but our priorities were features and IDE integration.
All of that said, I am guessing the flexui namespace in your project is pointing to an older version of the TestRunnerBase buried somewhere in the FlexUnit .9 project. We include FlexUnit .9 in its entirety for compatibility reasons, but it means that you can sometimes reference older classes. The appropriate namespace should be:
http://www.adobe.com/2009/flexUnitUIRunner
If that doesn't work, then you are missing the FlexUnit4UIListener.swc and your namespace is probably set differently. Here is another thread on this same issue:
http://forums.adobe.com/message/2252570#2252570
When configured correctly, your MXML file should read something like this:
<?xml version="1.0" encoding="utf-8"?>
<mx:Application
xmlns:mx="http://www.adobe.com/2006/mxml"
creationComplete="runMe()" xmlns:adobe="http://www.adobe.com/2009/flexUnitUIRunner">
<mx:Script>
      <![CDATA[
        import org.flexunit.listeners.UIListener;
        import compilationSuite.SuitesToRun;
        import org.flexunit.runner.FlexUnitCore;
        private var core:FlexUnitCore;
        public function runMe():void {
          core = new FlexUnitCore();
          core.addListener( uiListener );
          core.run( compilationSuite.SuitesToRun );
    ]]>
</mx:Script>
<adobe:TestRunnerBase id="uiListener" width="100%" height="100%" />
</mx:Application>
I will give the wiki page you reference a read today and see if I can make things clearer,
Mike

XServe G4 System Drive not found and 2PFW/2/3:FireWire

I tried to Google "2PFW/2/3:FireWire" and only got one answer:
http://macgroup.infopop.cc/eve/forums/a/tpc/f/418609942/m/7401083361
I thought it maybe a drive module problem, as this is the only thing I haven't tried yet.
I changed slot, tried diskutil, fsck but I haven't change disk in drive module.
Is there any other feedback on this ?
How could I repair a disk I even can't see in disk utility ?
OS: 10.3.9 Server.

With the Hardware Test CD, sorry, I forgot to tell that. I've tried about everything (diskutil, fsck, PRAM, slots and drive modules) during last night in the datacenter and I think I won't be able to recover data from this disk. I'm not sure this error is related to the faulty drive. I fthis is only a firewire bus error I don't care as I don't use FW on my server.
Too bad I didn't get preventive information from smart.

Old iPod mini can't be recognized after formatting, and iTunes 'Apple Mobile Device Driver not found.'

My roommate gave me an old iPod Mini a few days ago. It was working fine 'til I plugged it into my computer and it asked me to format it. I did, and now it cannot be recognized by iTunes or my computer. My computer views it as a "removable disk" which cannot be accessed. In devices, it is listed as an Apple iPod though, so I'm hoping not all is lost. I have tried many quick fixes I've read on internet (including changing disk letter) but to no avail. I have reinstalled the new iTunes and now that is telling me it has not installed properly, and when I ran diagnostics, it reads that the Apple Mobile Device Driver not found. I will copy & paste all the info from the diagnostic run below, and if anybody can help me with my new (old) iPod, I'd be everly greatful!
Thanks!!
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
TOSHIBA Satellite L775D
iTunes 11.0.1.12
QuickTime 7.7.3
FairPlay 2.2.32
Apple Application Support 2.3.2
iPod Updater Library 10.0d2
CD Driver Not Available
CD Driver DLL 2.1.3.1
Apple Mobile Device 6.0.1.3
Apple Mobile Device Driver not found.
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number
Current user is not an administrator.
The current local date and time is 2013-01-08 11:16:27.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
ATI Technologies Inc., AMD Radeon(TM) HD 6520G
**** External Plug-ins Information ****
No external plug-ins installed.
**** Device Connectivity Tests ****
iPodService 11.0.1.12 (x64) is currently running.
iTunesHelper 11.0.1.12 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Standard OpenHCD USB Host Controller. Device is working properly.
Standard Enhanced PCI to USB Host Controller. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Most Recent Devices Not Currently Connected:
iPod mini running firmware version 1.4.1
Serial Number: JQ******S42
<Edited By Host>

OMG same thing here; rather annoyed and now have set up accounts on 2 comps(both 64 vista ultimate); about to try my 32 bit vista on my lappy; we'll see... i don;t have high hopes thoush.
What i knew about iPhone before buying it:
What You Need
To use iPhone, you need:
A new two-year wireless service plan with AT&T
A Mac or a PC with a USB 2.0 port and one of the following operating systems:
Mac OS X version10.4.10 or later
Windows XP Home or Professional with Service Pack 2 or later
Windows Vista Home Premium, Business, Enterprise, or Ultimate edition
iTunes 7.3 or later, available at www.itunes.com
An iTunes Store account
An Internet connection
You must be at least 18 years old to open a new AT&T wireless account. You will need a
major credit card to open a new iTunes Store account.
Yeahyeah check all that stuff;
Oh well; just when i thought i'd finally cross over to the beautiful packaging of APPLE. I remember in design school that form follows function. Thanks.
Windows Vista

ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified in windows server 2008 r2

ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified in windows server 2008 r2.I made a application in asp.net c#.I am using ODBC connection.When I deployed my application in windows server2008 r2.There
is no Microsoft ODBC driver shown in ODBC Data source administrator.Then I go to the C:\Windows\SysWOW64 and open Odbcad32.exe and add Microsoft ODBC2 driver for Oracle and when I run my application I got following error
ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified
I am using follwoing string
<connectionStrings>
<add name="theconnetion" connectionString="DSN=abdb;UID=abc;PWD=xyz"/>
</connectionStrings>
Guide me What I do?

Did you add a System DSN or a User DSN? If you added a User DSN from your own login, the asp.net application will not be able to use it unless its application Pool in IIS is configured to run under the same credentials that you used for creating
the DSN. It's better if you add a System DSN.
Also, be careful to ensure that you are using a 64 bit DSN, unless you configure the application to run in 32 bits. If the 64 bit application attempts to use the 32 bit driver you get the same error message "Data source name not found and no default
driver specified". See this KB article:
http://support.microsoft.com/kb/942976/en-us

SQL Server Reporting Services: ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified

Hey everyone, So I am trying to get a report onto the server, and in BIDS I kept getting a login screen repeating over and over when I tried to deploy my report, so I tried to upload the file at http://<servername>/Reports This worked, but then trying
to run this report from http://<servername>/Reports did not work either because "An error has occurred during report processing. (rsProcessingAborted) Cannot create a connection to data source 'FTYDataSource'. (rsErrorOpeningConnection) For more information
about this error navigate to the report server on the local server machine, or enable remote errors" Anyways I tried to add a New Data Source (which I would use in the report) at http://<servername>/Reports, type ODBC, with the connection string Dsn=blah_blahblah.
I try to test the connection here and get the error ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified This is really getting old fast, everything I try, a new error comes up. Granted I am new at this,
but this still should not be this troublesome. Does anyone have any ideas on what could FINALLY allow me to just put a report out onto the server?!? THANK YOU in advance for ANY help.

Hi,
Please try setting the credentials of the datasource.
1. Double click and open the datasource in your project.
2. Click on the credentials tab, and click on option button 'Use this username and password'
3. Enter the username and password to connect to the datasource
4. Deploy or upload the datasource to the report server and try accessing the reports.
Hope this helps.
Please click "Mark as Answer" if this resolves your problem or "Vote as Helpful" if you find it helpful.
BH

Core Audio: Selected Driver not found. (-10202) error message and speakers don't work

Apple just replaced my hard drive and now I'm noticing that I have no sound coming out of my internal speakers or earphone jack. When I try to use garage band I get the following error message:
Core Audio:
Selected Driver not found (-10202)
I read their article on the subject; I go to system preferences, sound then output devices where I'm supposed to select my device except there are none listed. I tried to fix the problem by reinstalling the operating system using the CD's that came with the MacBook Air but that didn't work either.
Here's the other problem, when I download the software update the update never loads. The status bar just sits there even when I let my pc alone over night.
Any suggestions??
FYI, i can't easily walk into a mac store for assistance.. gotta catch a plane to a different island.

Update your Apogee and Symphony drivers to Mountain Lion versions...
But the bigger question is.. How did you install Mountain Lion on a G5?

Linked Server [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified

Hi I have SQL2012 installed on my local machine and have also installed MySQL 5.6.23 installed with a test database.
I also have my SQL connector installed and MYSQL ODBC Driver 3.51.
Which happily connects to the Mysqldb.
The Datasource Name : mySQL conn
TCP/IP Server : localhost and Port :3306
User root
with pwd
On the SQL side I have used the following
EXEC master.dbo.sp_addlinkedserver
@server = N'MYSQLSRV',
@srvproduct=N'mySQL conn',
@provider=N'MSDASQL',
@datasrc=N'mySQL conn'
However when I try to selet using open query
SELECT * FROM OPENQUERY ( [MYSQLSRV], 'SELECT * FROM students' )
it comes back with
OLE DB provider "MSDASQL" for linked server "MYSQLSRV" returned message "[Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified".
Msg 7303, Level 16, State 1, Line 1
Cannot initialize the data source object of OLE DB provider "MSDASQL" for linked server "MYSQLSRV".
I cant understand what I have done wrong . Any help in this would be great as Ive hit a bit of a brick wall

Hi Robert3975,
In addition to other post, please also note the following things.
1. If you use the 32-bit driver on a 64-bit machine, please run the 32bit version of "odbcad32.exe" by running "c:\Windows\SysWOW64\odbcad32.exe"
from Start/Run menu and
create your ODBC DSN. However, for the 64-bit driver, use c:\windows\system32\odbcad32.exe to create your ODBC DSN. For more details, please review this similar
thread.
2. Expand the folder Providers under Linked server directory in SSMS and go to properties of MSDASQL provider and configure it properly as described in this blog:
Creating Linked server to MYSQL from SQL Server.
Thanks,
Lydia Zhang
If you have any feedback on our support, please click
here.
Lydia Zhang
TechNet Community Support

Error: Datasource name not found and no default driver specified

HI All,
I have MySQL as my data base.
I created one universe on top of MySQL. Then i made one webI report on top of that and exported it to BO Portal (Infoview).
Now when I am refreshing this report, it gives me below error in Infoview while its getting refreshed in WebI.
[Database Error] [Microsoft ODBC Driver manager] Datasource name not found and no default driver specified.
WIS 10901
I found SAP Note 1200396 and have created DSN with Same name on Server.
But still I am facing same problem. I have not clustered enviroment.
Guys any one have some idea about this?
I will appreciate your answer.
Thanks in advance,
Rishit

If your BOBJ server runs on 64bit windows you should set up the DSN using the 32bit ODCB utility (<Windowa installation director>\SysWOW64\odbcad32.exe )
Regards,
Stratos

Data source name not found and no default driver specified.

Hi all,
I am using Microsoft Accessas as backn'd. when I am starting my Presentation Services I am getting this error> Data source name not found and no default driver specified.

Your presentation services configuration file
$SADATADIR/web/config/instanceconfig.xml
contains an entry DSN which is the connection to the bi server
then inside your RPD(s) loaded by the bi server
you will have various connection pools in the physical layer
which connect to physical data sources such as MS Access
you can test a physical database connection
by right clicking a physical table
then "View Data" or "Update Row Count"

Webi Refreshing Error :database name not found and no default driver specified

Hi All,
When I refreshing the webi report from Launchpad getting bellow error
"database name not found and no default driver specified"
Bellow is the Screen shot
It is refreshing in webi Rich client (server and client tools are in same system) but not from Launch pad
1. Environment :BI 4.0 SP4
2. Server and client tools are installed in same system
3. Created a 32 bit odbc, universe connection is responding properly and report refreshing in rich client(I could not find 64 bit odbc) .
Can Please suggest me where I am doing wrong
Regards,
Mahi

Hi Mahi,
Seems like your BO server is 64 bits and you have created a 64 bits DSN; whereas your database requires 32 bits DSN.
Try below steps:
1. Navigate to the C:\Windows\SysWOW64 directory and open odbcad32.exe. This will open the ODBC Data Source Administrator for 32-bit drivers on the 64-bit server. NOTE: The ODBC Data Source Administrator that is located by clicking Start and Administrative Tools will only create 64-bit ODBC connections.
2. Click on the System DSN tab
3. Click on Add to create a new Data Source
4. Provide the database details
5. Your 32-bit ODBC data source is now ready for use.
Hope it will help.
Regards,
Yuvraj

EIS : Data source name not found and no default driver specified

Hi
I have Oracle Essbase installed in a x86_64 machine.
I have configured odbc 64 bits how is indicated in SQL Interface Guide, but when try to create catalog the message "ODBC Error [DataDirect][ODBC lib] Data source name not found and no default driver specified"
The is.sh script set these environment variables:
#!/usr/bin/ksh
export ISHOME=/u01/app/oracle/Middleware/EPMSystem11R1/products/Essbase/eis/server
export EPM_ORACLE_HOME=/u01/app/oracle/Middleware/EPMSystem11R1
export HYPERION_HOME=/u01/app/oracle/Middleware/EPMSystem11R1
export ARBORPATH=$ISHOME
export ESSBASEPATH=$ISHOME
export ISLOADINFO=$ISHOME/loadinfo
export ISODBC=$EPM_ORACLE_HOME/common/ODBC-64/Merant/6.0
export ODBCINI=$EPM_ORACLE_HOME/common/ODBC-64/Merant/6.0/odbc.ini
export TEMP=/tmp
case `uname` in
AIX)
export JAVA_HOME=$EPM_ORACLE_HOME/../jdk160_11
export LIBPATH=$ISHOME/esslib:$ISHOME/islib:$ISODBC/lib:$JAVA_HOME/lib:$LIBPATH;;
HP-UX)
export JAVA_HOME=$EPM_ORACLE_HOME/../jdk160_11
export SHLIB_PATH=$ISHOME/esslib:$ISHOME/islib:$ISODBC/lib:$JAVA_HOME/lib:$SHLIB_PATH;;
Linux)
export JAVA_HOME=$EPM_ORACLE_HOME/../jdk160_11
export LD_LIBRARY_PATH=$ISHOME/esslib:$ISHOME/islib:$ISODBC/lib:$JAVA_HOME/lib:$LD_LIBRARY_PATH ;;
SunOS)
export JAVA_HOME=$EPM_ORACLE_HOME/../jdk160_11
export LD_LIBRARY_PATH=$ISHOME/esslib:$ISHOME/islib:$ISODBC/lib:$JAVA_HOME/lib:$LD_LIBRARY_PATH;;
echo `uname -a`;;
esac
export CLASSPATH=$EPM_ORACLE_HOME/common/jlib/11.1.2.0/epm_j2se.jar
export PATH=$JAVA_HOME/bin:$ISHOME/bin:$PATH

Hi Andres, Can you please tell me how you resolved this issue? I'm getting the same error when I start EIS as windows services, but when I start from console it works fine.
Updated................Issue resolved!!!
OK. Upon researching other windows forums found that I had to add System DSN to ODBC administrator under "C:\Windows\*SysWOW64*\odbcad32.exe". This is because the server is a windows 64-bit machine.
Thanks
Edited by: U12345 on Dec 14, 2010 5:58 AM
Edited by: U12345 on Dec 14, 2010 6:01 AM

Getting "Data source name not found and no default driver specified"

Hi all,
I'm trying to create a connection in SQL Developer (1.5.0.53) to an Access MDB using the Access Tab on the "New / Select Database Connection" window. I navigate to my MDB and then click the Test button and this is what I get:
"Status : Failure - Test failed: [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified"
I do have the 1.6 JVM.
Not a show stopper, but would like to see how SQL Developer works with Access tables, so any help would be appreciated.
TIA,
Steve

This error message sounds like the MS Access ODBC driver or the Jet Engine drivers are not found. First of all you need to check the PATH environment setting if it includes the windows/system32 directory as this is the default directory for the MS Access ODBC drivers.
Next check if you are a normal user or a local admin user. As local admin open the ODBC Adminstartor (Control Panel/administrative tools) and check if a MS Access ODBC driver is registered.
If all above is true, please get from www.sysinternals.com and et the process monitor. Open it and apply a filter: Process name is sqldevloper.exe
Then start SQL Developer and open your created MS Access link. Process mon will now track all info containing all additional DLLs it tries to load.
Check out the generated log file from the bottom (last info about the mdb file load) to the top and look if it really finds all libraries, especially the MsAccess and Jet libraries.

WIS: 10901 Data source name not found and no default driver specified(ODBC)

Hi, gurus.
We've created a universe based on Excel spredsheet or MS Access which is using ODBC connection. Then, I try to create query (which is using these universe) in QAAWS or in InfoView, and when I add a filter object to the query, the error occurs:
"GetDatasourceObject LOV exception (error WIS: 10901)".
If I don't choose any filter options and want to create query, I'm getting the error: ' [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified (error WIS: 10901)'.
We tried to do this in different operations systems - Windows 7 (32 bit) and XP (32 bit).
Anymore, we can use this universes at web intelligence rich client with or without filters.
Need to solve this problem. Please help us.

Dear all,
I got the same problem, I have installed BOE 4.0 at Win XP 64 bits, and also installed Sybase IQ 15.2 (32bit) ODBC, and has create the odbc entry "shkdemo" at the System Tab. However, I still got the same error when using the the "Interactive Analysis" thru "BI Launch pad".
For BOE 4.0, I found that I could only use the BOE Client tools (Universal Design Tool) to create the connection, this client tool I installed it at another 32 bit XP laptop, and I also installed the Sybase IQ 15.2 (32bit) ODBC with the same odbc entry "shkdemo", and using the "Interactive Analysis Desktop, I could be able to create report with data from IQ 15.2.
Kindly advise, why I still got the error of "10901 Data source name not found and no default driver specified(ODBC)" when I use the "Interactive Analysis" thru "BI Launch pad".
Cheers,
Hilda

SATA Drive not found and other stuff.

Similar Messages

Maybe you are looking for