SATA: ERROR: Giving up on I/O, Reliance Not Supported on Certain Models?

Hello All, 
I did not want to latch on to a resolved post, but I find the solution a bit under explained. I have a PXI System (8102 Controller, 1078 Low Power Chassis) that encounters the following errors after about 3 days of continuous run time:
SATA: ERROR: Giving up on I/O [0x25] transfer 0
SATA: ERROR: Giving up on I/O [0x35] transfer 0
I have read through this post, seemingly the only other documented instance of this behavior:
http://forums.ni.com/t5/PXI/SATA-ERROR-Giving-up-o​n-I-O-0x35-transfer-0/td-p/1992475
Proof that this is happening: 
I am going through the process of reformatting to see if FAT32 will stabilize the system for longer run time; however, I would like to know if there are limitations on the use of Reliance as a RT file system? Are there specific models that are not supported? 
The failure modes that indicate this error has occurred are not consistent. I have seen full system crashes when this error occurs, and I have also seen the system in a partially functional state (network communication interacts with my main application; however, the controller cannot be discovered by MAX). Is there any more detailed understanding of this error (and avoiding it), other than 'Something somewhere is corrupt'?
During the troubleshooting process of this issue I have reformatted the system multiple times (though never to FAT32). Is there a fundamental known issue with Reliance or CAR related to this behavior? I will begin FAT32 testing now, but have a few days of testing before I can share results. 
Any insights on this issue are greatly appreciated, 
~Pcorcs

Hello Patrick,
Reliance system, should be compatible with all PXI systems. This is an odd issue that has been observed a couple of times in the past, a few CAR´s has been created, the service requests I checked, all of them ended up in a RMA process. The only workaround among the CAR´s I found is to disable the RAID option if present in the BIOS, however from a technician perspective I would recommend you to perform the FULL FAT32 formatting process ( not a quick format) in order to detect possible bad sector on the HDD, another option will be get a tool like HDD regenerator, that can check and most of the time, repair bad sectors
Regards
Mart G

Similar Messages

  • Error Message: This type of file is not supported, or the required codec is not installed?

    I am trying to get media from my computer, and I only receive this error message :
    This type of file is not supported, or the required codec is not installed?
    What should I do? I have a window 8 laptop. My video files are from my itouch/ipod. I am using Premiere Elements 7.
    I have used this software with success before. HELP would greatly be appreciated!

    darlingdarleen
    Did both laptop 1 and 2 have QuickTime (latest version or any version) installed on the computers with Premiere Elements 7 when you got this "this type of file......" message?
    If you go to the opened Premiere Elements 7 projects involved and look at Share/Personal Computer/QuickTime, do you find that QuickTime Presets are shown and that you find export settings choices under the Advanced Button/Video Tab and Audio Tab?
    Look at the file name of the video. Do you see any irregularies in the name of the file, dots and such?
    If you record new iPod footage, open a new Premiere Elements project, and import that iPod footage, do you still get the error message? Putting aside, iTouch, what model iPod are these videos coming from?
    Thanks.
    ATR

  • Error message "Live file system repair is not supported."

    System won't boot. Directed to Disk Utility to repair but get error message "Live file system repair is not supported."  Appreciate all help.
    Thanks.
    John

    I recently ran into a similar issue with my Time Machine backup disk. After about 6 days of no backups - I had swapped the disk for my photo library for a media project; I reattached the Time Machine disk and attempted a backup.
    Time Machine could not backup to the disk. Running Disk Utility and attempting to Repair the disk ended up returning the "Live file system repair is not supported" message.
    After much experimentaion with disk analysis softwares, I came to the realization that the issue might be that the USB disk dock wasn't connected directly to the MacBook Pro - it was daisy-chained through a USB Hub.
    Connecting the USB disk dock directly to the MBP and running Disk Utility appears to have resolved the issue. DU ran for about 6 hours and succesfully repaired the disk. Consequently, I have been able to use that Time Machine disk for subsequent backups.

  • While trying to setup a time capsule backup to my MyBookLive external drive, I got the following error message: The network backup disk does not support the required AFP features. What's up with this?

    While trying to setup a time capsule backup to my MyBookLive external drive, I got the following error message: The network backup disk does not support the required AFP features. What's up with this?

    This means that your NAS does not support the required encryption. Update your NAS to the latest firmware or ditch it and buy a Time Capsule (they are the most reliable when using TM).

  • Java.lang.Error: JAX-RPC 1.1 method is not supported in WLS 8.1 clients.

    We have some web services that run under OC4J 10.1.3.4. We have various JEE 'client' apps (JSF, servlets etc.) that use these web services. These JEE apps also run under OC4J.
    We started a migration project from oc4j to weblogic 10.3.2. In phase 1 we want to move these JEE 'client' apps to weblogic. In phase 2 we want to move the web services themselves to weblogic with adjustments to the JEE 'client' apps as needed.
    However we ran into an issue during this phase 1. Deploying these JEE 'client' apps to weblogic results in an error like this:
    java.lang.Error: JAX-RPC 1.1 method is not supported in WLS 8.1 clients. If you are attempting to run an OC4J 10.1.3 JAX-RPC client in WLS, please see the Web Service Migration Guide for instructions.
    We are including Oracle web services client libraries (http://download.oracle.com/otn/java/oc4j/1013/wsclient_extended.zip) in these JEE 'client' apps's war files because weblogic does not have them.
    What part of Web Service Migration Guide is the above error message talking about? Do we have to re-generate the client side proxies for all these web services using weblogic's clientgen task in 'JAXRPC' mode? Many of these web services are doc/literal jax-rpc web services. Or does the migration guide recommend we migrate the web services first to weblogic? Any other specific information on working around this error message would be greatly appreciated.

    Hi,
    I had the same issue but I just managed to fix it. You must upgrade and/or regenerate you proxy. This creates new classes (possibily in a new package) that you must use in your code. I had this error because the classes directory was not clean after the rebuild and the old classes (in the old package) were still present, so the compilation was successful with the old classes. So clean your classes directories, regenerate your proxy and use the new classes in your code.
    Regards,
    Sylvain

  • Exchange 2010, khi: failed to execute Troubleshoot-DatabaseSpace.ps1 Error formatting a string: Format string is not supported

    Hi,
    Exchange 2010 MP fails to run Troubleshoot-DatabaseSpace.ps1. Results in a Warning with "Error formatting a string: Format string is not supported". The EventNumber is 402. The Microsoft article it points to is useless at http://technet.microsoft.com/en-us/library/749e0eac-ebb2-41e3-8fa2-4a03a1bd3571.aspx 
    Run ".\Troubleshoot-DatabaseSpace.ps1 -Server MailboxServer.domain.com -MonitoringContext" and works fine.
    Any help appreciated.
    thanks

    Hi,
    Before the newer MP release, we can disable  these 4 monitor via override and this should not run the Troubleshoot-DatabaseSpace.ps1 :
    KHI: Failed to execute Troubleshoot-DatabaseSpace.ps1.
    KHI: The database copy is low on database volume space and continues to grow. The volume is under 25% free
    KHI: The database copy is low on database volume space and continues to grow. The volume has reached error levels under 16% free.
    KHI: The database copy is low on database volume space and continues to grow. The volume has reached critical levels 8% free.
    Alex Zhao
    TechNet Community Support

  • ERROR:MapLib:973 - Tri-state buffers are not supported in this architecture.

    Hi,
    I face a ERROR:MapLib:973 problem with inout port in a pcore component.
    I need ton instantiate an inout port at the top level to communicate wih my peripherical.
    This inout port is driven by an XPS IP core (pcore).
    The .mpd is  :
    PORT fdata = "", DIR = INOUT , VEC = [31:0], ENABLE=SINGLE, THREE_STATE = TRUE,TRI_I = fdata_I, TRI_O = fdata_O, TRI_T = fdata_T
    PORT fdata_I = "", DIR = I , VEC = [31:0]
    PORT fdata_O = "", DIR = O , VEC = [31:0]
    PORT fdata_T = "", DIR = O
    The .vhd is :
    fdata_o : out std_logic_vector(31 downto 0);
    fdata_i : in std_logic_vector(31 downto 0);
    fdata_t : out std_logic ;
    I got ERROR:MapLib:973 - Tri-state buffers are not supported in this architecture messages for each
    signals of my fdata PORT, while mapping !
    Thanks for you help.

    What device are you targeting, and what version of the software are you using?
    I target a xc7k325t-fbg676-2.
    I use ISE 14.3 form platgen to xst and 14.7 from map to bitgen.
    What does your top level HDL (verilog or VHDL) file look like (where the IO must be instantiated)?
    It is a .vhd in whitch i wrapp my top XPS core, described by .mhs
    The problematic IO port is instantiated into the mb_core.vhd (generated by XPS).
    If i open it, i could see that the tool correctly infer the corresponding IOBUF's :
    component mapping :
    fdata_I => FX3_DQ_I,
    fdata_O => FX3_DQ_O,
    fdata_T => FX3_DQ_T,
    One IOBUF infered:
    iobuf_1 : IOBUF
    port map (
    I => FX3_DQ_O(31),
    IO => FX3_DQ(31),
    O => FX3_DQ_I(31),
    T => FX3_DQ_T
    Top level port :
    FX3_DQ : inout std_logic_vector(31 downto 0);
    THEN FX3_DQ  signal is dirrectly branched in my upper level (top level) vhd file, with the same name.
    What do your constraints file look like (where the pin number and names get declared)?
    The port is only constrained in .ucf, like that:
    NET FX3_DQ[0] LOC = "B24"| IOSTANDARD = LVCMOS33 ;
    NET FX3_DQ[31] LOC = "G26"| IOSTANDARD = LVCMOS33 ;#Bank 14
     

  • When I publish a SWF/HTML5 module with Captivate 8 and try to run it using IE9 - I get the following error "The content you are viewing is not supported in the current Document Mode" - anyone know why?

    When I publish a SWF/HTML5 module with Captivate 8 and try to run it using IE9 - I get the following error "The content you are viewing is not supported in the current Document Mode" - anyone know why?

    TLCMediaDesign wrote:
    I've seen a lot of threads about getting rid of these kind of messages. Those messages are there for a reason most of the time. If you have CSS animations or other HTML5 standards that cannot be rendered in IE9 they won't magically start working becuse you got rid of a message. I use IE9 since that is the minimum standard for the client. I have never seen that message publishing to HTML5 content.
    IMO, if your client has IE9 I think that you should develop with IE9 in mind not IE11.
    When you say "develop with IE9 in mind not IE11" do you mean use SWF instead of HTML5? I used the standard question types, and a converted PowerPoint presentation. I didn't add anything out of the ordinary.

  • Error in Installing Netweaver--domain controllers are not supported

    When i make the pre-requisite check for installing Netweawer 2004s
    I am getting the follwoing error
    <b>installation to domain controllers are not supported</b>
    Pls help me how to resolve this
    Thanks in Advance

    hi balaji,
                  FYI,
                         You cannot create local users and groups on the host that is used as domain controller. Therefore, we do not support running an SAP instance (including the database instance) on the host where the DNS service is installed.
    so try to log with a user, who has administrator rights. and check whtr all the services are up & running. then try to re-install.
    for more on this refer the installation manual.
    hope this will help you.
    with regards,
    Rajesh.
    <i> plz, award with suitable points </i>

  • I just received my i phone 4,inserted Amayim with 4G plan,but showing noservice and bar with emergency calls only screen.Also when i down loaded i tunes to my laptop (windows7) there is an error(9808) message saying i tunes store not supported completely.

    i just received my i phone 4,inserted Amayim with 4G plan,but showing noservice and bar with emergency calls only screen.Also when i down loaded i tunes to my laptop (windows7) there is an error(9808) message saying i tunes store not supported completely.

    first of all the iphone 4 is not a 4G phone
    second it sounds like your iphone could be locked to another operator then the sim you have inserted

  • DAQmx Error: Non-buffered hardware-timed operations are not supported for this d evice and Channel Type.

    Hello,
    I am new to NI and to data acuasition cards in general. I am trying to put an application togather that would play large audio file using NI9263.
    And i am getting the following error.
    DAQmx Error: Non-buffered hardware-timed operations are not supported for this device and Channel Type.
    Status Code: -201025
    Does my hardware support buffering ?
    can i use the EveryNSamplesCallbackAO function ?
    Any sample code, will be helpful at this time. Thanks.

    Hi yma200,
    Are you using a USB 9263?  If so, this might be of help:
    http://digital.ni.com/public.nsf/allkb/EC1968728E660B288625780700570D06?OpenDocument
    If it doesn't help, can you please post the code that you have that is causing your error?
    Regards,
    Bogdan Buricea
    Applications Engineer
    National Instruments

  • Currently using Flash Pro CS5,  getting error when trying to open CS4 file.  Error is "Slides and Forms documents are not supported in this version of Flash. Please open in previous version.

    Currently using Flash Pro CS5,  getting error when trying to open CS4 file.  Error is "Slides and Forms documents are not supported in this version of Flash. Please open in previous version.  Has there been a fix or patch to this issue or do I have to convert back to CS4 to open the file?

    Having the same problem in CS6.  I can tell you that converting back to CS4 will NOT solve the problem.  It seems when support for backward compatibility is discontinued, there's just no way to get
    any help at all?  Absolute failure to provide any user support so far...

  • Getting error Dynamic navigation to this object is not supported in CRM 7.0

    Hi All,
    I am getting Error " Dynamic navigation to this object is not supported " when I am tryiong to Create a Follow up request " Service Request " for the interaction record in SAP CRM 7.0. I have tried to find a solution using the Navigation bar profile where we define the generic outbound plug mapping however I have no good luck regarding this... :-(
    Regards,
    AB

    Hi All,
    I am getting Error " Dynamic navigation for object CRM_SRQM_INCIDENT and action B not supported " when I try to run a task workflow for a  "Service Request " .
    I have tried to find a solution using the Navigation bar profile where we define the generic outbound plug mapping however I have no good luck regarding this.
    attached a sample screen
    Regards,

  • Error 2148074306 The encryption type requested is not supported by the KDC

    Our domain is Windows 2008 Native. I ran repadmin /replsummary and noticed an odd error that I cannot get to the bottom of. Error 2148074306 The encryption type requested is not support by the KDC. This appears between two DCs only. I cannot find any reference to what might be causing this.Orange County District Attorney

    Hello,
    check this articles about:
    http://blogs.technet.com/ad/archive/2007/11/02/server-2008-and-windows-vista-encryption-better-together.aspx
    http://social.technet.microsoft.com/Forums/en-US/winserverDS/thread/9fe02655-bab9-43e4-9776-7b318b582e19
    http://blogs.technet.com/ad/archive/2007/02/23/aes-authentication-in-vista-keep-in-mind-if-you-re-testing-vista.aspxBest regards
    Meinolf Weber
    Disclaimer: This posting is provided "AS IS" with no warranties, and confers
    no rights.

  • OBIEE Error[14041] Nested Aggregation measure are currently not supported

    Hi,
    Please provide workaround for the OBIEE Error[14041] Error in measure definiion. Nested aggregation measures are currently not supported.
    I have two logical columns - Current YTD Invoice Quantity and Prior YTD Invoice Price. I want to create a column which is -
    (Current YTD Invoice Quantity * Prior YTD Invoice Price)/ sum(Current YTD Invoice Quantity * Prior YTD Invoice Price)
    sum in the denominator should be the sum of all rows returned by the report. So level based measures cannot be used as there are multiple report and dimension used may vary.
    Columns Current YTD Invoice Quantity and Prior YTD Invoice Price are already aggregated to Sum.
    If I try to do the sum on the physical column while creating logical column, the query is running for 6-7 hours and not giving any result. Both the columns belong to different alias table in physical layer.
    Please let me know if you guys know any work around for this issue. Also let me know whether this type of nested aggregation are supported in 11g or not?
    Thanks.

    Hi Adil,
    Yes, I did create a hierarchy for the time dimesion.
    No, I was not able to specify the aggregate rule since the source of the logical column is another logical column
    But the time hierarchy works for rows that is not based upon the SUM aggregate at the answers level.
    Say I have 3 columns: Income,Expense, Bottom Line (formula : Income- Expense)
    Income is created based upon a case statement in the Logical Column and
    Expense is also created based upon a case statement in the Logical Column.
    Income 1000 Rupees
    Expense -300 Rupees
    Bottom Line 700 Rupees (where the Bottom line is a row based upon the Answers aggregate formula
    which is SUM(Income+Expense))
    When I add a column year, I get the following output
    Income 2009 500 Rs
    Income 2008 500 Rs
    Expense 2009 -150 Rs
    Expense 2008 -150 Rs
    Bottom Line 2009 700 Rs
    Bottom Line 2008 700 Rs
    The Bottom Line doesn't spread across the Year
    Hope this helps you to understand what my problems is.
    Thank you!

Maybe you are looking for