Sata hd on P67-GD65

Hi, my pc will only boot into windows when my sata drives are set to IDE only, will this make them run slower than ACH mode?

What Windows Version are you using?
Which SATA-Port(s) are you using?
What is your current BIOS/UEFI Version?
Quote
will this make them run slower than ACH mode?
You mean AHCI Mode? Well, the answer is: Not necessarely.

Similar Messages

New RAM for my P67-GD65 B3

I can't decide, plz help me Which 2x4GB RAM to buy?
1. Geil PC3-14000 1750MHz C9 Enhance PLUS (DDR3 1750MHz, 9-9-9-28, 1.5V)
2. G.Skill F3-12800CL8D-8GBECO (DDR3-1600MHz, 8-8-8-24-2N, 1.35V)
I will try to get 1333MHz with lower timings and I would rather stay bellow 1,5V. G.Skill looks better on paper but much pricey in shop.
My system:
- Intel 2500K@4500 (1,35 idle->1,4V stress)
- P67-GD65 B3
- now I have 2x2 Corsair 1600 8-8-8-24-1T 1,65V
- ATI HD4890
- Samsung Spinpoint F1 500GB Sata II
- SoundBlaster X-Fi Gamer PCI
- Windows 7 HP 64bit SP1
- Ante True Power Trio 650W, 52A on 12V.

Quote from: HU16E on 13-April-11, 03:40:04
What is wrong with the Corsair? Those have 1333 9 9 9 24 @ 1.50v. SPD profile don't they? Have you actually tried lowering the DRAM V. to them at 1333? Tried tightening the timings?
Yes! I can try of course but... I borrowed Corsairs from TR3X6G triple channel kit. I have to buy a whole new kit, so I wanna go with 2x4GB and not 4x2GB. I am almost sure that sooner or later I will try to add additional 2x4GB. My problem for now is that I can not find reviews with low voltage, tighter timings ram kits. Means: made for SB cpu.
Sadly, no one mentioning those Geils :/
When I see Geil spec: 1750MHz, 9-9-9-28 on 1,5V I can only speculate what timings I get on 1333MHz.
I wish getting 1333 with low voltage (1,5) and low timings (7-7-7-20). Like we all Impossible? Maybe.
G.Skills ECO are even closer to this with: DDR3-1600MHz, 8-8-8-24-2N, 1.35V.
Sorry to say I am starting to quoting myself. I am too old for this but...
Those mems do not look like ram: 1600MHz 8-8-8-24, 1,65V and then we have a "wonderful" 1333, 1,5 , 9-9-9-24 spd timing!
You know what I mean... Corsairs above will not run 1600MHz on 1,5V. I can test what timings I get when 1,5V on 1333MHz.
Well, maybe I am a bit too optimistic and somebody should try to help me getting back on planet Earth, hehehehe.
BTW1: Crucial 2x4GB kit not available in Poland :/ and those 2x2GB are all 1,65V.
BTW2: Did I mention that I need rather low profile kit? Ouch. My heatsink lays above ram slots. Corsair CMX/TR3X size is ok.
BTW: Thank You all for answers. Thank You very much

Sandybridge MSI P67-GD65 with Cayman MSI R6970 Short Test :)

Just for share and I think this post is already late because there are lots of reviews in the net for the new ATI 6970 video card. At least we can say that this would be a real benchmark score and I personally did the run. Also, I’m using Intel’s new Sandybridge for the tests and I will enumerate the configuration later on.
The video card I have here is a MSI ATI R6970-2PM2D2GD5. Specs are 2GB of GDDR5 Mems running at 5500mhz / 880mhz Default Core Clock / 256Bit and with 1536 Unified Shaders.
Plain and simple design box but its huge
Accessories
More photos of the card
You have 1 Dual-Link DVI Port / 1 Single-Link DVI / 2x Mini Display Port and lastly an HDMI connection With one card alone you can actually have 4 displays for Eyefinity
Pencil case look for the Top Side hehehehe 1x 8pin and 1x 6pin Power Inputs
Next for my Test Configuration System:
Quote
• Processor: Sandybridge i5 2500 3.3ghz
•Motherboard: MSI P67-GD65
•Mems: Plain 2x 2GB DDR3 1333mhz
•PSU: AcBel R8 1100watts
•HDD: WD Caviar Green 500GB SATA
•Softwares: Windows 7 32bit / ATI Catalyst 10.11 Driver / 3dmark06 and Vantage with latest patch
Stock Benchies
3dMark06 24k
Vantage 19k
Next Oc’ed i5 2500 to 3.9ghz just to check if there are still bottlenecks for the new Sandybridge You decide hahahaha
3dMark06 26k
Vantage 20k
Lastly, Both VC and Proc oc’ed
3dMark06 27k
Vantage 21k
That’s it . Thanks!!!!

@zsde
this is an AVC Global Star Cooler. Actually all 3rd party market 1156 coolers are still compatible with the new sandybridge sockets So if you have one, your safe already

P67-GD65 B3 Replacement DOA

I did the msi exchange program on my P67 chipset.
Sent my fully working GD65 board to msi for the B3, got the B3 and installed to find its dead.
Really not happy with the time and costs to take time off work to get it sorted for msi to send me a duff board.
Anyway, what to do? Was I just unlucky our do I go back to Asus and forget about msi..
If I do stick with msi who do I contact about ANOTHER board? Scan.co.uk where I bought my B2 board from or back to msi who sent me a dead board?

Apologies..
i5-2500k
P67-GD65 (B3) BIOS unknown due to fault
XMS3 1600 4GB (2x2GB)
1GB Palit 460GTX
OCZ Vertex 3 SSD / 1TB WD SATA
Netgear PCI Wireless
Windows 7 (64bit)
XFX Black Edition 850w
When I turn on all fans spin, hard drive lights and power light on. Monitor flashes standby mode. Blue motherboards lights are all lit solid.
No display, no beeps, no POST.
Tried reseating everything, booting with one stick RAM in various slots, no pci cards etc etc.
Tried clearing CMOS.
One thing I did notice was my motherboard box contents were not organised like my first motherboard box from the shop. Could this be a dead motherboard sent to me by mistake?

MSI P67-GD65 (B3) Did I make a bad choice? I'm building a new system!

After reading all the problems everyone seems to be having with boot problems and freezing, did I make a bad choice? Here's what I'm putting together when the parts arrive.
It's been a few years since I built my own rig, but every pc I've ever owned I built myself except my Dell XPS 630i (got a screaming deal).
MSI P67-GD65 (B3)
Intel i7-2600K unlocked and unleashed
CORSAIR high performance Vengeance memory module 8GB (2x4GB) 1600MHz 9-9-9-24, 1.5V
Sapphire AMD Radeon HD 6970 2GB GDDR5 PCI-E 1080P
Western Digital Caviar Black 1T Hard Drive
Dell XPS 630i Case and Delll 750W power supply (I know I shouldn't reuse this case)
Windows 7 Ultimate 64bit

"Dell XPS 630i Case~I know I shouldn't reuse this case"
Poor case for cooling with quad CPU and higher power consuming VGA card as you sure will end up with high temperature problems. It would be wise to get a better case.

MSI P67-GD65 running 4 DIMMS slots

Hello,
I have two kits of memory:
2x2Gb 1600 cl7 1.65v (that runs at 1.5v with same latencies 7-8-7-24)
2x4Gb 1600 cl9 1.5v (9-9-9-24)
Both kits are Gskill Ripjaws, I have already tried lots of things without any success so far, (relax timings to high values, increase voltage, tried link/unlink, swapped kits from black to blue), I cannot boot with RAM set to 9-9-9-24 (whether 1 or 2T) and 1600Mhz, the only way is to disable XMP and let memory speed to auto.
And so memory is recognized and runs in Windows at around 1310Mhz~1315Mhz with timings 7-7-7-20 (values chosen by me since I cannot use higher speeds).
In case I set memory speed to manual, whether its 1333Mhz or other values I get three long bips and I am unable to boot.
CPU Core i7 2600K
MSI P67-GD65 (B3) using latest official bios (1.E)
Actual position of the memory:
DIMM0:4Gb
DIMM1:2Gb
DIMM2:4Gb
DIMM3:2Gb
Thanks for your kind help.

Quote from: Jack on 14-November-11, 22:45:26
Thanks for your help Jack, this explains my issue.
I am still used to SDRAM, I mixed different sizes, brands, single and dual sided, even speeds, it always run without problems.
I need to get used.
Quote from: Henry on 15-November-11, 14:47:34
And the fact that they are the troublesome Ripjaws to begin with. Mixing one type of troublesome Ripjaws with another type of troublesome Ripjaws and you end up with double trouble.
I see, despite of the fact Ripjaws are mentioned as compatible, I should avoid them as they mean trouble.
RIP Ripjaws
What brand would you recommend?

MSI P67 GD65 Boot Beep change after bios flash 1H & 1I

Good evening.
First of all my pc specs:
- Msi P67 GD65 B3 Revision
- i5 2500K
- 2 * 4 gb DDR 3 G.Skill Ripjaws XF3 1600 mhz
- Sapphire HD 4870
- Ocz Vertex II 60 Gb (windows 7)
- Western Digital Blue Caviar 1 tb (storage)
Today I flashed the bios using a bootable pen drive.
Previously I had the 1.9 version and all went perfectly fine. The booting sequence was : 1 short beep, short beeps counting my usb devices and 1 final short high tonality beep.
Now I updated to version 1.I and the beep sequence changed completely: now I have 1 long low tonality beep, short beeps counting my usb devices and no final short high tonality beep . Also it takes some more seconds than version 1.9 before making the beeps!
I tried also versione 1.H (which I have in this very moment) and I experienced the same faulty beep sequence
I also tried to clear c-mos and load optimized defaults but I still have the same beep sequence in both cases.
What shall I do?
Please notice I never changed memory or cpu settings (no overclock at all)

Quote
They say do not care about the beeps if the PC could work normally.
Same thing I already told you...
Forgot about those stupid beeps. As long as the system starts & boots fine, they are not critical error signals to begin with but status signs, that tell you that some things are there.
Quote
What do they mean by "the new bios should fix some beep error" ? Which bios are the talking about? Maybe the upcoming 1 L version which is going to be released in future?
What they are telling you is that the beep sequence is not something to worry about. That the beeps "lie" so to speak and that you are looking for a meaning that is not there.
Quote
What beep sequence do you have with 1.C version compared to the two videos I posted ?
It does not matter. You are getting hung up on beeps even though the system is obviously running just fine. If the beeps are getting on your nerves, then unplug the speaker from the board and enjoy the silence.
This is a non-issue. Stop being paranoid.

MSI P67-GD65 + 3770K overclocking

Hi,
I've used my P67-GD65 for almost 2years now in combination with an Intel Core i7 2600K and I was able to overclock just fine. Ever since I flashed my GD65 to v4.1 and v4.2 to support my new 3770K I can't overclock anymore (aside from Intel's default turbo of upto 39x). Also ECO mode and OC Genie mode are unresponsive in the BIOS.
Does Anyone know how to fix this?
Thanks for reading,
-Blade-

I copied the bios of a forum member that's able to OC his 3770K on his P67 GD55 and I'm stll not able to... It showed him having 45x 100MHz but it only applies 3497MHz for me
My Bios
Forum member's BIOS

[P67-GD65 B3] Safe way to flash 4.2 official bios and why.

Hi all!
I am still trying to remedy my problem with too high (~1.43V) voltage while 4.5GHz OC (turbo or not) with "vdroop low" enabled. Now I am on 4.39 and it`s ok on (non turbo/manual x42) 4.2GHz and auto voltage (it`s ~1.288V while Prime, etc). I know that 4.20 official bios gives % vdroop settings. I want to try it to avoid my problem but I can not find 4.20 package ready to go with MSIHQ flasher. Actually all 4.xx MSIHQ versions go from 4.3x.
I am wondering if it is possible just to compress "valcheck.com" with 4.20 official bios file and throw it via Mode 1 to MSIHQ(?)
BTW: Maybe it (flashing 4.20) does not make any sense because "%" vdroop on 4.20 will not give me anything higher then "Auto" voltage settings. I think I need ~1,38V to get stable 4.5GHz. Any other ideas?
I could try manual voltage for CPU but I want to stay with energy saving c-states. I am using C1E with my non turbo OC.
I know You can find my problem a bit boring but maybe forum's Gurus could give me a green or red light(?)

Just to report!
Yesterday I finally tried to down-flash from 4.39 to 4.20 with MSIHQ. Risk taken Happily it was success!
But boy ... I should read carefully comments about 4.20 bios (grammar lost). I did not know that on this bios 100% vdroop is not ... How to say it? It is not 100% of "vdroop low" but rather 100% of "vdroop auto". So it not helped me with my main problem. I am now back to 4.39 beta bios.
BTW1: After some tests, I found that while on CPU voltage on "Auto" my CPU max voltage is ~1,29V (never more, it stabilize more or less from x40 multi CPU) while stress testing. Switching to "Low vdroop" I get above 1.4V just from x40 multi. Something is not right. It goes up with higher multi.
I tried to workaround this by Control Center. Switched to lower multi in bios, switched vdroop to "low" (voltage was OK and below the 1,4V line while stress testing) and then bump up multi in CC. Guess what ... Voltage was also bumped to the same (too high) values.
BTW2: I started to think that above problem may be my fault. From start with my P67-GD65 I experimented with OC Genie and maybe I switched some values or even reseted CMOS while using OC Genie (I know that was warning about it). I don't know, but maybe it damaged something and my motherboard behaves like this for good :/
I think that it is the end of my experiments. Bios 4.20 (% vdroop) was my last resort, but it failed.
Big thanks for all that tried to help me . It started 07-April-12:
https://forum-en.msi.com/index.php?topic=158139.msg1161554#msg1161554
I have to stay on x42 with ~1.288 voltage or go above x45 with more than 1.43V.

P67-gd65 / i5 2500 problem

Hi all.
Brand new setup just in and no luck so far.
Everything new out of the box and connected up but it doesnt seem to power up somehow.
* On first power up the APU / phase leds goes up to active 3 leds. System Fans and CPU fans work, vid card fan works.
* Then the system just resets after a few seconds.
* The system starts up and resets *again* within a second (it seems even less).
* Then system tries to power up again and the APU / phase leds just goes up to 1 active led.
* The systems seems to hang at this state, all fans blowing full, no response on monitor so bios not even reached it seems.
I guess the problem is power related but i am kinda at a loss.
The system is :
p67-gd65
Intel I5 2500
ocz PC3 10666 (3g1333LV8GK gold series 9-9-9) 2x4gig matched
CM realpower 550 PSU
2x F3 spinpoints plus some older 36gig stat drive.
saphire 5770 or sapphire 6850 vidcard
I could not find any info yet on POST / startup problems and the system doesnt seem to give much hints ( like beeps or something =).
Any clues on what the problem is ?

Quote
Where are the days that each board has atleast some basic form of diagnostic beeps or leds..
Status Beeps should be audible as soon as a speaker is connected to the respective pins of the JFP2 pin header (see mainboard user manual). Do you have a speaker connected to JFP2?
Quote
if the bios doesnt support the CPU's its made for.
Have a look at the BIOS chip(s) of the board. There should be a sticker on it/them telling you the factory BIOS Version.
What about this?
Quote
Have you tested the board outside the case on an non-conducting surface?

[P67-GD65] OC CPU and voltage. After one year I still do not understand...

It is "provoked" by this fantastic post:
https://forum-en.msi.com/index.php?topic=157376.0
Quote from: Bernhard on 03-March-12, 19:06:19
My CPU is able to OC to 4,5 with all settings on Auto in the BIOS...
2500K running 4500MHz 1,367V on "Auto"? I can only dream about it and I am not talking about CPU but MB!
My 2500K is running 4500MHz with "int. overvoltage" option enabled but I have to chose:
1. set multi x45, CPU voltage to 1,340V, vdrop to auto - CPU-Z shows 1,384 running Prime - it`s ok IMHO, but no drop to low, idle voltage.
2. set multi x45, CPU voltage to auto, vdrop to Low - CPU-Z shows 1,424 running Prime -
or
3. set multi x42, CPU voltage to auto, vdrop to auto - CPU-Z shows 1,280 running Prime - it`s ok
I see from table that on 4100MHz Bernhard get (assuming "Auto") 1,352V! How? Maybe vdrop was set to "Low"(?) Heh... I get 1,408V with vdrop "Low" while running 4200MHz! It is the same as running auto OC Genie/Moron with button.
In other words... I do not know what is so special with Bernhard's settings to get 1,376V running 4500MHz on "Auto". I know that test was on Z68 and using multimeter but is it possible that voltage oc settings are so different (means broken) on P67-GD65 or maybe it is just a simple user error on my side(?)

Quote from: Jack on 07-April-12, 23:31:00
Yes, that is possible and that does definately not mean something is broken.
"Definately" is a rather strange word in my opinion. Please, do not get me wrong it is (again!) just my opinion.
Quote from: Bernhard on 08-April-12, 00:20:36
I understand your question and possible frustration...
Frustration? No, no, no! I am rather happy with my gaming rig I just want to know, understand more.
So... Could You tell me your Vdroop setting? It is very strange that on "Auto" I get 1,280V (4200MHz, Prime blend, its ok) and You get 1,352V (IMHO too much without vdroop option) on 4100MHz. This is huge difference. Is it just a CPU batch difference? Mind You, when I switch vdroop to "Low" (I have only "Auto" and "Low" here) CPU voltage reading goes to 1,408V (4200MHz, way too much voltage!) testing Prime.
BTW: Older P67-GD65 bioses have Auto, Low and High vdroop settings. AFAIR Low and High was the same. Am I wrong?

P67-GD65 voltage options

Hello,
I was wondering if there is a way to adjust the voltage by offset on P67-GD65 board? I'm currently using v1.8b6 version of BIOS and can't find this option. If voltage is set manually to any value other then Auto it won't drop when CPU is idle - with both EIST and C1E enabled.
Thanks

Quote from: Jack on 25-February-11, 18:08:30
Contact MSI Technical Support here:
http://support.msi.com/
The form you have to fill out does not require you to choose your mainboard model from a pre-compiled list. It is a free form that allows you to enter whatever you got into the respective fields (Model Name, M/B ERP Version, M/B ECN version, BIOS Version).
Again, this is a user-to-user forum, not a support platform run by MSI Technical Support but by users just like you. In average, we have a little over 255 postings per day here, which adds up to more than 1700 postings per weeks (more than 7600 postings per month) concerned with all kinds of different problems (and very often pseudo-problems) with a large variety of different MSI Retail Products. "Browsing" through these posts "once in a while" is definately not the job of MSI's technical support teams as that would most definately keep them from doing their actual job.
We do not need to debate about this further. If you have a particular issue that is definately BIOS or UEFI related, then it can only be fixed via a BIOS or UEFI Update. We do not make BIOS or UEFI releases here. That means we can not help you with those and that is why contacting MSI Technical Support under the above mentioned address is what you should be doing instead of complaining in here.
MSI Tech. 02/25/2011 Please contact the office which handles your region, as we only handle the U.S. and Canada and do not provide over clocking support, so they can advice you on what your options are. You can use the link below to find the proper office. http://www.msi.com/language/
Well Jack, contacting Tech Support online was certainly a good use of my time.
The thing is, I don't think the Engineers even saw my query, because I'm sure someone with a technical mind and devotion to a product they created would have a bit more professional pride when it doesn't work well. A typical customer service monkey basically told me to get lost, they don't want to know.
Because my region, the UK website, explicitly tells me the UK arm only deals with repair and mainteance and for technical issues I must go elsewhere, the "global" service. And in anycase, I don't want an RMA. I want an engineer to have a look and come up with a BIOS revision.

P67-GD65 not downclocking at idle

I had a bash at OC'ing my 2600K installed in my P67-GD65. I tried changing the turbo boost first which worked yet didn't downclock at idle then I tried disabling the turbo boost and just changed the multiplier yet that also didn't downclock at idile. I have all the energy saving stuff enabled yet nothing changes.
After getting annoyed I hit the CMOS button and reset everything and now it downclocks at idle but only at stock clocks... I'm at a loss of why its doing this.
My specs :
2600K
P67-GD65
8GB Vengeance LP RAM
GTX 780TI
GTX460
AX750

It depends on how and what settings are selected. For OC with power saving, I like C-State disabled, EIST and C1E enabled. CPU V. can't be taken out of Auto or the CPU V. will not reduce down at idle or low use, although the CPU speed probably will. I prefer the Turbo Core Ratio OC getting the highest stable clock possible on Auto CPU V. over the CPU Ratio OC method. Overspeed Protection, Spread Spectrum, and EuP 2013 should also be disabled.

P67-GD65, change Turbo multipliers in BIOS for overclocking

Hi,
Here are my specs
Intel Core i5 2500k
MSI P67-GD65 B3, Bios 1E
8GB Corsair ram
I have read a lot on guides and other forums on how it is possible to keep the base multiplier, i.e. at 33 and to go into the CPU features part in the Overclock menu and change the core limit for Turbo multipliers so that the over clock comes into effect when turbo kicks in. As yet, though I haven't been able to pull it off. I have changed the multipliers and increased the watts given in the menu. But still in windows the CPU only goes up to 34 multiplier. Even when I set the multipliers to a relatively tame 40.
Am I missing something here. Is this sort of thing not possible in the new BIOS, because all the guides and topics have referee to old or beta BIOS. Bt I don't want to start flashing them all and screw something up.
So any help will be appreciated. Thanks in advance

http://forums.overclockersclub.com/index.php?showtopic=183670
Please check down below where he shows how he over clocked using turbo, "Latest Successful Attempts using Speedstep Turbo overclocking"
That's basically what I am aiming for. I will be over clocking through the BIOS, I want to leave the base multiplier at 33 which is default for my processor and over clock by changing the turbo multipliers.
I have tried an older BIOS, 1.9. In it using the instructions provided I have been able to do what he mentioned and with prime95 my clock speed runs at 40x.
I'm trying each BIOS to see which one essentially killed this feature. Because in later BIOS this doesn't work and for some reason the turbo multiplier cap seems to be fixed at 60.
A review by Guru3D mentioned a similar way to overclock the board

P67-GD65 Memory Questions

Hi,
I have a P67-GD65 motherboard/I7 2600k and Cosair XMS3 2000MHz memory modules. When I use XMP in the bios it marks the memory at 1888mhz, but when I use the OC Genie button and boot into windows 7, MSI control center reports the memory at 1066. The CPU is OC to 4.2. Do you need to adjust the memory manually or could this be a display issue in control center?
Thanks

Your memory is an example of overclocked and overvolted 1066 chips.
See the max bandwidth in the SPD Tab. PC3-8500F (533) i.e. 1066 and that is what they defaulted to, correctly.
If you inspect the SPD tab you will see 4 JEDEC profiles the last one (XMP) being DDR3-2000 at increased timings but requiring 1,65V which is not JEDEC standard.
Based on these profiles you will have to manually set your memory in the BIOS.
Go into your BIOS and manually select a DRAM ratio that sets your memory to 1333. Set your memory timings manually to 9.9.9.26, those will be the first 4 timings in the list of manually adjustable timings.
Then test your system.If that is stable, then use the same timings but set the memory to 1600. For this test increase your DRAM voltage to approx 1,55V.
Test and report back.
You need a 64bit OS to be able to access more than about 3GB available RAM. If you have XP 32bit, you should have bought 2 X 2GB and saved a couple of dollars. You can read this thread as well. https://forum-en.msi.com/index.php?topic=108883.0

Sata hd on P67-GD65

Similar Messages

Maybe you are looking for