SATA in G4 (agp)

400mhz g4, running 10.4.9
Hi. I've added a XRack Serial ATA/ATA133 PCI card to drop another hard drive into my little beastie. The XRack card says it supports Ultra ATA133/100/66 and SATA, as well as drives over 137gigs.
The drive I've added is a WD Caviar GP 640gig SATA. It's "green," so it's speed is supposed to change from 5400 to 7200 depending on conditions. The manual said to leave the drive jumper-less unless used in an enterprise setting....I'm just a desktop, and this is the only drive connected to this card. I have the drive powered through an adapter from my last available 4 pin outlet.
PROBLEM: I can't Erase the drive.
System profiler CAN see both the hard drive and the card. Disk Utility CAN see the new hard drive...though it took about 10-15 minutes for the drive to appear. However, every time I try to Erase the hard drive, the operation times out.
From what I have read, this could be for any number of reasons:
- 128 gig limit with this old sawtooth G4? (but this one is connected through a pci card)
- new hard drive is "green"...could it be going too slow?
- wrong kind of hard drive for the pci card
- 400mhz processor is just to slow...
I've browsed the forum and googled about, but don't see any answers.
Any suggestions would be helpful.

mfg is Macsense....xrack card looks like this one:
http://www.macsense.com/Product/storage/sua-100e.html
the pamphlet with the card says it's all firmware, no mac drivers necessary or available.
here's an interesting post about it
http://www.xlr8yourmac.com/feedback/MacsenseSUA-100Ecard.html#storytop
I'm going to check my sata port jumpers and maybe try the cards internal A, I've been on B because it's always supposed to be "on"

Similar Messages

Major SATA problem!

I decided to buy a WD SATA 10k rpm 35G HD. I want to have the drive as my root with OS. I installed the drive to sata 2(near AGP), and rebooted to XP disk. I loaded XP on the disk(partitioned the drive into 2 parts 15/20). Setup loads files and reboots. I then get an error message " file missing or corrupt HAL.DLL". I know that has something to do with the boot.ini file. At that time my IDE drive was C: and D: and my Sata was E and F. So I decided to wipe my IDE drive and reload XP. After loading XP on my IDE successfully, I went for the install on the SATA. Again I got the same error about HAL.dll. I was guessing it was listing the wrong path in the boot.ini file. So I unpluged the IDE drive and moved my DVD to IDE 1 master and left IDE 2 blank with just the SATA drive installed.(YES, I enable SATA in the bios from the very start). I ran XP setup on the SATA drive (also repartitioning and formating again just incase), setup loads the files and reboots. After the "boot from CD, press any button" 5 dots load it give me an error "ERROR LOADING OPERATING SYSTEM". So I plugged back in my IDE HD to IDE 1 and dvd to IDE 2 leaving SATA in tact to log on and research. I can't figure this out to save my life. It seems like it's just a bios setting or possably a setup option i'm forgetting. I also upgraded my BIOS to 1.4
note: I have also tried changing to different SATA ports and reloading OS, I have also ran SETUP with raid on and off.
k8n neo2 platinum
AMD 939 3200 64bit
IBM fireball 30Gig IDE
WD raptor 10k 35G SATA
Pioneer DVD-rw/cd-rw

You need to have your IDE drives disconnected during windows install .
Install xp with only the sata drive connected , make the installation finished as
you like it , then shutdown and hook up the ide drives and boot up again to bios.
Make sure the HD boot drive selection is correct (sata first) ,save exit .
Boot to windows .
This will also make your sata drive host the neccesary boot files for the windows installation (makes it systemdrive/boot drive) . With ide drives in there
one of those will be boot drive for the win install ,and boot ini redirects with the rdisk parameter to sata . But the ide must be set as boot drive in hd boot selector.

Overclocking of MSI K8N neo platinium

MSI K8N neo platinium, Bios 1.4
Athlon64 3200+ 2000Mhz (200Mhz x10) 1MB cache, Clawhammer.
Geil 2x512MB DDR PC3200 400MHz Value CL2,5 5ns Aluminium Heat
Club3D 9800pro@xt
Hitachi Deskstar 7K250-160 160Gb 7200rpm 8Mb cache S-ATA
400w psu
Before when I had just one memory chip(512mb in slot 1), I had no problem to run 235Mhz x10. All I had to do was the following :
Put hdd in SATA 4
Set AGP to 68Mhz
Adjust cpu voltage from 1.45 - 1.55v
Set mem. clock to 166Mhz (sense it will increase as you raise the FSB)
Now I`ve bought one more identic memory chip. I have now 2x512MB memory placed in slot 1 and 3.
I followed the same steps as above, but with terrible results. Max 215Mhz x10 stable.
I`m pretty sure it`s not the memory chips that`s the problem, as they run stable
with original settings ( witch is higher speeds (200Mhz) than those I run on the memory when overclocking (166 - 195Mhz).
I would be greatfull for any tips or solutions that you might think would help me (and others) to reach better o/c results.

try slots 1+2 instead of 3, i have found that i can't oc very well in 1+3 either.

3000 and 3400 : Whats the difference in performance

my wife (being the wonderful woman she is) has ordered me an Athlon64 3400 for my birthday.
whats the perfomance difference like between the 3000 and the 3400, will i notice a difference at all ??
and does anyone know how well the 3400 overclocks ??

a 3400+ typically is faster than an overclocked 3000+. They both overclock in the same way. However overclocking any of these depends more on other componants and there tolerance to having the system clock changed. SATA drives and AGP cards are especially touchy about changes to the system clock.
Just the same if you can overclock say by 5% to a 3000+ then you should be able to do about the same to a 3400+.

New bios 655 max

http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=403&NAME=MS-6730
1.1 Update date 2003-2-11
Update Description -Update SATA bootROM
-Add AGP Fast Write in the BIOS setup

What video card are you using? If it's an ATI, install the Control Panel and disable AGP Fastwrites there (that's how I did it).
I have had little luck with the AGPUtil. One thing that could be causing your problems is a little known issue with the SiS AGP Drivers. Version 1.12 is the ONLY version that will work with the 655 chipset. Any newer versions will automatically install that driver (unless you manually installed v1.14 or 1.15, for example, which would cause serious problems--it did for me). AGPUtil won't even load in my case. If you did in fact manually load a newer version that 1.12, my suggestion would be to do a system restore and using the 'setup' program. I tried uninstalling and reinstalling, but it continued to have problems until I used System Restore. That or reinstall XP.
Hopefully you have an ATI card, which provides a nice little option for setting AGP rates and fastwrites.
Good luck.

KT6 Delta Fis2r and s-ata woes

Hello.
My current setup is a follows.
kt6 delta
xp3200+
1 gig ram
1 250gig quantum sata drive
nvidia agp gfx card
adaptec 2940 pci card
I boot xp off this sata drive, hanging on the via controller, and everything has been working just fine.
I then enable the onboard promise controller in bios, set it to raid mode (or else I can't find a single working driver) and attach a drive. I configure it in promise's bios, and boot xp to format and give it a drive letter.
Everything is working fine for a few minutes, then I lose ethernet. At first I thought my inet connection was down, but I had two other computers accessing it so it wasn't it. After a few retries the same thing happened again and again, I even got a bluescreen (irql_not_equal). The adaptec 2940 and the promise controller was sharing irq (19), and I found no way of overriding it.
Anyone with a reasonable solution or suggestion ?

try playing swap the pci slot with it

K8N Neo 2 Platinum Problem!When rising to 210fsb restarting,etc...

I have a big problem which makes me angry...Actually there exist some problems,but I only write two of them...Firstly,when i try to overclock as rising fsb to only 210, system restarts and resarts again and again;only when I return to default value,system works.It is just a one example to show us that mobo does not work well.Secondly,about the temperature,there is a problem.System sometimes opens with 37degree,sometimes with 43 degree;sometimes rises to 55 and 62,sometimes stops at 47-48.These are not only from idle temperature but also load.Which makes me angry,temperature is 55 degree at idle;and sometimes at load it is 49 etc..I tried my CPU and fan,ram modules etc.,on MSI Neo 4 SLI mobo,and there didnot happen any problem,involving these two.So,I think they are not normal,what should I do?
My system:AMD 64 939 3200+ CPU,MSI K8N Neo2 Platinum,MSI NX6800 VGA,2*512 ddr400 Hynix d43 ram,80GB Seagate SATA etc...

I did it;that is to say i know that i have to lower HT and i did.In detail,ram timings were 3-4-4-6 and 1T.I disabled D.O.T,Spread spectrum,Agrassive timings,high performance mode was manuel etc..So everything was suitable for o\c.Also I disabled Sata1-2,and connected to Sata 3 port.AGP frequency was 67,cool and quiet was disabled.HT was 4,I adjusted CPU ratio to *10 and I rised CPU frequency only to 210.So,everything was as which had to be,but system restarting again and again,works only if i return to 200 fsb...I am sure that the problem is arisng from mobo,because I tested my configuration on different systems.For example,I tried my CPU and ram modules on MSI K8N Neo 4 SLI mobo and there did not happen any problem,I was able to rich 2500mhz with HT4,250fsb*10.Temperature was accurate also.What can I do?If
I cannot o\c my system it is unsense to have this configuration and this mobo.I think,if i bring my mobo to service of MSI,they will say it is not our problem,as you know they don't accept o\c problems.I also think that they have to explain something to me as their D.O.T. technology supposed to work at %11 o\c.Please,someone say something to me and give me an advice.

Delta2 Platinum OC BIOS settings?

hey, just upgraded my K7N2 Delta - ILSR to a Delta2 Platinum!!, went to a LAN party (500 players) thinking it came with the B30 Bios, nope, had trobles all the way throught the lan, but got home and put it back to the B30 runs smooth as.
anyway i will be doing some extreme overclocking with this board so i would like to know what settings i should be changing.
these are the ones i'm going to change as per the book.
sata spectrum - disabled
agp spectrum - diabled
FSB spectrum - diabled
cell - all manual
DOT - disabled
RAM / CPU = 1:1 (till it goes past 210mhz)
S.M.A.R.T = enable **
Video BIOS cacheable - enable **
system BIOS cacheable - enable **
video RAm chacheaable - enable **
**i think i shouldnt do this till i have a stable overclock is this correct
please if you have any comments dont hesitate to reply as i dont want to currupt my sata or ata drive.
PSU info:
i have a SF 500w and soon i will be getting 2 Ultra X-connect 500w PSU's to play with, one to power my Peltiers.
info as follows:
SF 500w (14cm fan)
3.3v @ 32A, 5v @ 42A, 12v @ 30A, -5v @ 0.5A, -12v @ 0.8A, =5VSB @ 2.5A
Ultra X-connect 500w
+3.3V @ 28A, +5V @ 30A, +12V @ 34A, -12V @ 0.8A, -5V @ 0.3A, +5Vsb @ 2.0A

The settings I use on my board are as follows:-
High Performance Mode Manual
D.O.T Disabled
CPU Voltage 1.7V
Memory Voltage 2.7V (Auto)
AGP Voltage 1.5V
Adjust CPU FSB Frequency 200Mhz
Adjust CPU Ratio CPU Default
CPU Interface Aggressive
Adjust DRAM Freq Auto
Memory Timings Manual 11,2,2,2.5 for Crucial standard. 11,2,2,2 for Crucial Ballistix
FSB Spread Spectrum Disabled
AGP Spread Spectrum Disabled
SATA Spread Spectrum Disabled
I have the video and system bioses caching disabled together with video ram. I have not done much overclocking above 200Mhz but if you plan on doing so you will probably need high quality ram. You can use the "try before buy" overclocking method from within Windows if you are not sure of the capabilities of your hardware using Core Cell.

Extra power cable needed for a SATA drive in a G4 AGP "Sawtooth"?

If one adds a SATA controller card and a SATA hard drive to a G4 AGP "Sawtooth", will a power cable like the one at the below link be needed, or would the necessary power cabling ordinarily come with the drive?
[http://eshop.macsales.com/item/Micro%20Accessories/SATAPAY>
-John

Thanks for the additional information, japamac.
That would be Left (or right angle 270º) for the data cable.
Which of the below data cables would be more appropriate, the 18" long one or the 39" long one?
[http://eshop.macsales.com/item/Micro%20Accessories/SATA18L>
[http://eshop.macsales.com/item/Micro%20Accessories/SATA39L>
Power connectors would be a left angle 90º to get wires going up.
I found the below two (the first is the same one linked near the top of this thread):
[http://eshop.macsales.com/item/Micro%20Accessories/SATAPAY>
[http://eshop.macsales.com/item/Micro%20Accessories/SATAPA>
Is it okay to have one of the ends of a "Y" cable remain unconnected? I've done that with my existing ATA power cables, but I wanted make sure that that is also okay with the SATA power cables.

Rs480 windows-sata installation problem

Hi all,
Whenever I try to install windows in my system I press the F6 button and loads the sil3112 sata driver. The first time I tried this worked(win xp with no sps) and I got to install windows. But after sometime I decided reinstall windows. This time when I tried to install windows(win xp with sp1) with the usual procedure like loading the sata driver through F6 method it didnt work. When I reach the partitioning blue screen and when I give prompt to format the drive or partition it windows say that “however the disk does not contain a windows compatible partition” and thus have to exit.
The same thing happened when I tried to install xp 64bit with sil drivers given in msi site.
Please do help me with this problem.
My mobo specs are given below.
<<< System Summary >>>
< Processor >
Model: AMD Athlon(tm) 64 Processor 3000+
Speed: 1.79GHz
Model Number: 3000 (estimated)
Performance Rating: PR2687 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous, Write-Back, 16-way set,
64 byte line size
< Mainboard >
Bus(es): ISA X-Bus PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7093
Total Memory: 447MB DDR-SDRAM
< Chipset 1 >
Model: Micro-Star International Co Ltd (MSI) ???
(5950)
Front Side Bus Speed: 1x 199MHz (199MHz data rate)
< Chipset 2 >
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 2x 995MHz (1990MHz data rate)
Total Memory: 512MB DDR-SDRAM
Memory Bus Speed: 2x 199MHz (398MHz data rate)
< Video System >
Monitor/Panel: Samsung Samtron 40Bn
Adapter: ATI RADEON Xpress 200 Series
< Physical Storage Devices >
Removable Drive: Floppy disk drive
Hard Disk: ST320413A (19GB)
Hard Disk: ST380817 AS SCSI Disk Device (75GB)
CD-ROM/DVD: SONY DVD-ROM DDU1622 (CD 40X Rd) (DVD 5X Rd)
< Peripherals >
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
< MultiMedia Device(s) >
Device: Realtek AC'97 Audio
< Network Services >
Adapter: Realtek RTL8139/810x Family Fast Ethernet NIC
<<< Mainboard Information >>>
< Mainboard >
Manufacturer: Micro-Star
MP Support: 1 CPU(s)
MPS Version: 1.40
Model: MS-7093
System BIOS: 05/13/2005-RS480-SB400-6A666M4DC-00
< System Memory Controller >
Location: Mainboard
Error Correction Capability: None
Number of Memory Slots: 4
Maximum Installable Memory: 2GB
Bank0/1 - A0: None None None None DIMM 512MB/64
Bank2/3 - A1: Empty
Bank4/5 - A2: Empty
Bank6/7 - A3: Empty
< Chipset 1 >
Model: Micro-Star International Co Ltd (MSI) ???
(5950)
Bus(es): ISA X-Bus PCI USB FireWire/1394
Front Side Bus Speed: 1x 199MHz (199MHz data rate)
In/Out Width: 16-bit / 16-bit
< Logical/Chipset 1 Memory Banks >
Power Save Mode: No
Fixed Hole Present: No
< Chipset 2 >
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Bus(es): ISA X-Bus PCI USB FireWire/1394
Version: 1.02
Front Side Bus Speed: 2x 995MHz (1990MHz data rate)
Maximum FSB Speed / Max Memory:2x 1000MHz / 2x 200MHz
In/Out Width: 16-bit / 16-bit
IO Queue Depth: 4 request(s)
< Chipset 2 Hub Interface >
Type: HyperTransport
Version: 1.02
In/Out Width: 16-bit / 16-bit
Speed: 2x 995MHz (1990MHz data rate)
< Logical/Chipset 2 Memory Banks >
Bank 0: 512MB DDR-SDRAM 3.0-3-3-3CL 2CMD
Channels: 1
Speed: 2x 199MHz (398MHz data rate)
Multiplier: 1/9x
Width: 64-bit
Refresh Rate: 5.00µs
Power Save Mode: No
Fixed Hole Present: No
Notice 224: SMBIOS/DMI information may be inaccurate.
Tip 2511: Some memory slots are free so the memory can
be easily upgraded.
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
<<< CPU & BIOS Information >>>
<< Processor 1 >>
< Processor >
Model: AMD Athlon(tm) 64 Processor 3000+
Speed: 1.79GHz
Model Number: 3000 (estimated)
Performance Rating: PR2687 (estimated)
Type: Standard
Package: FC µPGA939
Multiplier: 9/1x
Minimum/Maximum Multiplier: 9/1x / 9/1x
Generation: G8
Name: M1F Athlon 64 (K8 ClawHammer) 90nm ?GHz+ ?V
Revision/Stepping: 1F / 0 (108)
Stepping Mask: DH8-D0
Microcode: MU0FF041
Core Voltage Rating: 1.400V
Min/Max Core Voltage: 1.400V / 1.450V
Maximum Physical / Virtual Add:40-bit / 48-bit
Native Page Size: 4kB
< Co-Processor (FPU) >
Type: Built-in
Revision/Stepping: 1F / 0 (108)
< Processor Cache(s) >
Internal Data Cache: 64kB Synchronous, Write-Back, 2-way set, 64
byte line size
Internal Instruction Cache: 64kB Synchronous, Write-Back, 2-way set, 64
byte line size
L2 On-board Cache: 512kB ECC Synchronous, Write-Back, 16-way set,
64 byte line size
L2 Cache Multiplier: 1/1x (1791MHz)
< Upgradeability >
Socket/Slot: Socket 939
Upgrade Interface: Unknown
Supported Speed(s): 3.00GHz+
< Processor Power Management >
Processor Throttling Enabled: Yes
Throttle Range: 34% - 100%
<<< PCI(e), AGP, CardBus Bus(es) Information >>>
<< Generic >>
<< Interface >>
< System Buses >
PCI 64-bit Bus(es): 1
PCI 66MHz Bus(es): 1
PCI Bus(es): 3
Interface Version: 2.20
< Interface Properties >
Config space access mechanism :Yes
Config space access mechanism :No
Cycle generation mechanism 1 s:No
Cycle generation mechanism 2 s:No
<<< Video System Information >>>
<< Video Adapter >>
<< Primary Display Driver (display) >>
< Video Adapter >
Model: ATI RADEON Xpress 200 Series
Chipset: ATI RADEON Xpress 200G Series (0x5954)
RAMDAC: Internal DAC(400MHz)
Video BIOS: BK-ATI VER008.020I.030.000
VGA Compatible: No
Total Memory: 64MB (64MB Video) (118MB System)
Texture Memory: 182MB
Supports DIME Texturing: Yes
< Video BIOS >
Date: 04/12/20
< Current Video Mode >
Mode: 1024x768 16M+ TrueColour (32-bit)
Current Refresh Rate: 60Hz
Virtual Desktop Size: 1024x768
< Video Driver >
Model: ati2mtag.sys
Version: 6.14.10.6490
Expected Windows Version: 4.00
Video Acceleration: Yes
Screen Saver Active: 60 minutes(s)
Screen Saver Name: C:\WINDOWS\System32\logon.scr
Low Power Saving Active: No
Power Off Saving Active: No
<<< Sound Card Information >>>
<< Wave Input Devices (Recording) >>
<< Realtek AC97 Audio >>
< General Information >
Device Name: Realtek AC97 Audio
Manufacturer: Microsoft
Version: 5.10
Product ID: 101 / 1
With regards and concern,
Cherian

Quote from: Ui30 on 04-July-05, 19:41:11
Why not install like you did before, not using a slipstreamed version? It may do the trick!
Are you runnign single SATA? (I didn't find it in your summary, may looked over it ... maybe you can give your specs like in my signature )
i'll try you way.but its difficult to get a pure xp. i'll have to dig hard for that.
for ur 2nd question. i am not running a single sata. i have one sata 80gb and another 20 gb ide.is that a problem

Sata Errors on start-up.

Hello, when I boot my laptop it gives me a repeating error after the Grub screen.
[164266.343653] ata1.00: exception Emask 0x0 SAct 0xf SErr 0x0 action 0x6 frozen
[164266.343662] ata1.00: failed command: WRITE FPDMA QUEUED
[164266.343671] ata1.00: cmd 61/08:00:b8:02:47/00:00:13:00:00/40 tag 0 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[164266.343676] ata1.00: status: { DRDY }
[164266.343680] ata1.00: failed command: WRITE FPDMA QUEUED
[164266.343688] ata1.00: cmd 61/80:08:c0:02:47/00:00:13:00:00/40 tag 1 ncq 65536 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[164266.343692] ata1.00: status: { DRDY }
[164266.343702] ata1.00: failed command: READ FPDMA QUEUED
[164266.343709] ata1.00: cmd 60/00:10:e8:29:30/01:00:18:00:00/40 tag 2 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[164266.343713] ata1.00: status: { DRDY }
[164266.343716] ata1.00: failed command: READ FPDMA QUEUED
[164266.343724] ata1.00: cmd 60/00:18:e8:2a:30/01:00:18:00:00/40 tag 3 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[164266.343727] ata1.00: status: { DRDY }
I am able to boot into my system, but it often will go through this error about 3-5 times.
smartctl -a /dev/sda give me
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG MZHPU128HCGM-00000
Serial Number: S1ACNYAD532800
LU WWN Device Id: 5 002538 60000baf3
Firmware Version: UXM6401Q
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Jan 24 15:52:31 2014 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5f) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1484
12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 5417
177 Wear_Leveling_Count 0x0013 097 097 017 Pre-fail Always - 299
178 Used_Rsvd_Blk_Cnt_Chip 0x0013 088 088 010 Pre-fail Always - 151
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 089 089 010 Pre-fail Always - 272
180 Unused_Rsvd_Blk_Cnt_Tot 0x0013 089 089 010 Pre-fail Always - 2352
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
there are no logged errors which i find interesting.
This is what i get from dmesg, you can see the ata stuff about halfway down, included thee rest in case it is relevant.
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdf200000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88011fa00000 s86464 r8192 d24128 u524288
[ 0.000000] pcpu-alloc: s86464 r8192 d24128 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1008698
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=/dev/sda1 rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3951964K/4098932K available (5116K kernel code, 807K rwdata, 1628K rodata, 1144K init, 1288K bss, 146968K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:8448 nr_irqs:984 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 16777216 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.003333] tsc: Detected 2294.540 MHz processor
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4590.29 BogoMIPS (lpj=7648466)
[ 0.000005] pid_max: default: 32768 minimum: 301
[ 0.000027] Security Framework initialized
[ 0.000033] AppArmor: AppArmor disabled by boot time parameter
[ 0.000034] Yama: becoming mindful.
[ 0.000286] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.001041] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.001369] Mount-cache hash table entries: 256
[ 0.001524] Initializing cgroup subsys memory
[ 0.001546] Initializing cgroup subsys devices
[ 0.001548] Initializing cgroup subsys freezer
[ 0.001549] Initializing cgroup subsys net_cls
[ 0.001550] Initializing cgroup subsys blkio
[ 0.001570] CPU: Physical Processor ID: 0
[ 0.001571] CPU: Processor Core ID: 0
[ 0.001575] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.002546] mce: CPU supports 7 MCE banks
[ 0.002557] CPU0: Thermal monitoring enabled (TM1)
[ 0.002567] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0
tlb_flushall_shift: 6
[ 0.002659] Freeing SMP alternatives memory: 20K (ffffffff819e9000 - ffffffff819ee000)
[ 0.003422] ACPI: Core revision 20130725
[ 0.012141] ACPI: All ACPI Tables successfully acquired
[ 0.019369] ftrace: allocating 20317 entries in 80 pages
[ 0.027987] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.060971] smpboot: CPU0: Intel(R) Core(TM) i5-4200U CPU @ 1.60GHz (fam: 06, model: 45, stepping: 01)
[ 0.060979] TSC deadline timer enabled
[ 0.060986] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.060992] ... version: 3
[ 0.060993] ... bit width: 48
[ 0.060994] ... generic registers: 4
[ 0.060995] ... value mask: 0000ffffffffffff
[ 0.060996] ... max period: 0000ffffffffffff
[ 0.060997] ... fixed-purpose events: 3
[ 0.060998] ... event mask: 000000070000000f
[ 0.098662] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.084392] smpboot: Booting Node 0, Processors # 1 # 2 # 3 OK
[ 0.140519] Brought up 4 CPUs
[ 0.140522] smpboot: Total of 4 processors activated (18363.16 BogoMIPS)
[ 0.144090] devtmpfs: initialized
[ 0.146069] PM: Registering ACPI NVS region [mem 0xca4bb000-0xca4c1fff] (28672 bytes)
[ 0.146071] PM: Registering ACPI NVS region [mem 0xdab56000-0xdbaaafff] (16076800 bytes)
[ 0.146906] RTC time: 17:26:02, date: 01/24/14
[ 0.146938] NET: Registered protocol family 16
[ 0.147017] cpuidle: using governor ladder
[ 0.147018] cpuidle: using governor menu
[ 0.147040] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.147042] ACPI: bus type PCI registered
[ 0.147043] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.147085] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.147086] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.153209] PCI: Using configuration type 1 for base access
[ 0.153712] bio: create slab <bio-0> at 0
[ 0.153800] ACPI: Added _OSI(Module Device)
[ 0.153802] ACPI: Added _OSI(Processor Device)
[ 0.153803] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.153804] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.155436] ACPI: EC: EC description table is found, configuring boot EC
[ 0.202559] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.204584] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.205103] ACPI: SSDT 00000000dab34c18 003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.205507] ACPI: Dynamic OEM Table Load:
[ 0.205509] ACPI: SSDT (null) 003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.214255] ACPI: SSDT 00000000dab34618 005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.214935] ACPI: Dynamic OEM Table Load:
[ 0.214937] ACPI: SSDT (null) 005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.227395] ACPI: SSDT 00000000daae6d98 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.227971] ACPI: Dynamic OEM Table Load:
[ 0.227973] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.241337] ACPI: Interpreter enabled
[ 0.241348] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130725/hwxface-571)
[ 0.241356] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
[ 0.241378] ACPI: (supports S0 S3 S4 S5)
[ 0.241380] ACPI: Using IOAPIC for interrupt routing
[ 0.241412] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.241594] ACPI: No dock devices found.
[ 0.286876] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.287110] acpi PNP0A08:00: Requesting ACPI _OSC control (0x1d)
[ 0.287277] acpi PNP0A08:00: ACPI _OSC control (0x18) granted
[ 0.287950] PCI host bridge to bus 0000:00
[ 0.287952] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.287954] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.287956] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.287957] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.287959] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.287960] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.287961] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.287962] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 0.287964] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 0.287965] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 0.287966] pci_bus 0000:00: root bus resource [mem 0xdf200000-0xfeafffff]
[ 0.287974] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[ 0.288152] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[ 0.288163] pci 0000:00:02.0: reg 0x10: [mem 0xf6400000-0xf67fffff 64bit]
[ 0.288170] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.288174] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.288346] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[ 0.288353] pci 0000:00:03.0: reg 0x10: [mem 0xf7d14000-0xf7d17fff 64bit]
[ 0.288546] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[ 0.288562] pci 0000:00:14.0: reg 0x10: [mem 0xf7d00000-0xf7d0ffff 64bit]
[ 0.288614] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.288748] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.288780] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[ 0.288799] pci 0000:00:16.0: reg 0x10: [mem 0xf7d1c000-0xf7d1c01f 64bit]
[ 0.288862] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.289032] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[ 0.289045] pci 0000:00:1b.0: reg 0x10: [mem 0xf7d10000-0xf7d13fff 64bit]
[ 0.289100] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.289235] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.289270] pci 0000:00:1c.0: [8086:9c14] type 01 class 0x060400
[ 0.289338] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.289476] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.289513] pci 0000:00:1c.3: [8086:9c16] type 01 class 0x060400
[ 0.289580] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.289719] pci 0000:00:1c.3: System wakeup disabled by ACPI
[ 0.289754] pci 0000:00:1c.4: [8086:9c1a] type 01 class 0x060400
[ 0.289822] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.289960] pci 0000:00:1c.4: System wakeup disabled by ACPI
[ 0.289995] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
[ 0.290014] pci 0000:00:1d.0: reg 0x10: [mem 0xf7d1a000-0xf7d1a3ff]
[ 0.290097] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.290246] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.290278] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[ 0.290534] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[ 0.290547] pci 0000:00:1f.3: reg 0x10: [mem 0xf7d19000-0xf7d190ff 64bit]
[ 0.290564] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.290836] pci 0000:01:00.0: [8086:08b1] type 00 class 0x028000
[ 0.290876] pci 0000:01:00.0: reg 0x10: [mem 0xf7c00000-0xf7c01fff 64bit]
[ 0.291040] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.291084] pci 0000:01:00.0: System wakeup disabled by ACPI
[ 0.297349] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.297356] pci 0000:00:1c.0: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.297440] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.297445] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
[ 0.297449] pci 0000:00:1c.3: bridge window [mem 0xf7200000-0xf7bfffff]
[ 0.297455] pci 0000:00:1c.3: bridge window [mem 0xf0a00000-0xf13fffff 64bit pref]
[ 0.297600] pci 0000:03:00.0: [144d:a800] type 00 class 0x010601
[ 0.297671] pci 0000:03:00.0: reg 0x24: [mem 0xf6810000-0xf6811fff]
[ 0.297687] pci 0000:03:00.0: reg 0x30: [mem 0xf6800000-0xf680ffff pref]
[ 0.297750] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.297784] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 0.307334] pci 0000:00:1c.4: PCI bridge to [bus 03]
[ 0.307338] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.307342] pci 0000:00:1c.4: bridge window [mem 0xf6800000-0xf71fffff]
[ 0.307347] pci 0000:00:1c.4: bridge window [mem 0xf0000000-0xf09fffff 64bit pref]
[ 0.307382] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[ 0.328006] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.328066] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 10 11 12 14 15)
[ 0.328122] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12 14 15)
[ 0.328177] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.328232] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.328287] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.328352] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 0.328401] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.328837] ACPI: Enabled 3 GPEs in block 00 to 7F
[ 0.328844] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.328934] Found 1 acpi root devices
[ 0.329121] ACPI: EC: GPE = 0x7, I/O: command/status = 0x66, data = 0x62
[ 0.329212] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.329215] vgaarb: loaded
[ 0.329216] vgaarb: bridge control possible 0000:00:02.0
[ 0.329252] PCI: Using ACPI for IRQ routing
[ 0.330513] PCI: pci_cache_line_size set to 64 bytes
[ 0.330545] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.330547] e820: reserve RAM buffer [mem 0xca4bb000-0xcbffffff]
[ 0.330548] e820: reserve RAM buffer [mem 0xca8e5000-0xcbffffff]
[ 0.330549] e820: reserve RAM buffer [mem 0xda898000-0xdbffffff]
[ 0.330551] e820: reserve RAM buffer [mem 0x11fe00000-0x11fffffff]
[ 0.330617] NetLabel: Initializing
[ 0.330618] NetLabel: domain hash size = 128
[ 0.330618] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.330629] NetLabel: unlabeled traffic allowed by default
[ 0.330642] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.330651] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.332671] Switched to clocksource hpet
[ 0.336308] pnp: PnP ACPI init
[ 0.336319] ACPI: bus type PNP registered
[ 0.336423] pnp 00:00: [dma 4]
[ 0.336442] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.336459] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.336535] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.336627] system 00:03: [io 0x0680-0x069f] has been reserved
[ 0.336629] system 00:03: [io 0x2008-0x200b] has been reserved
[ 0.336631] system 00:03: [io 0xffff] has been reserved
[ 0.336632] system 00:03: [io 0xffff] has been reserved
[ 0.336634] system 00:03: [io 0x1c00-0x1cfe] has been reserved
[ 0.336635] system 00:03: [io 0x1d00-0x1dfe] has been reserved
[ 0.336638] system 00:03: [io 0x1e00-0x1efe] has been reserved
[ 0.336640] system 00:03: [io 0x1f00-0x1ffe] has been reserved
[ 0.336641] system 00:03: [io 0x1800-0x18fe] could not be reserved
[ 0.336643] system 00:03: [io 0x164e-0x164f] has been reserved
[ 0.336645] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.336668] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.336702] system 00:05: [io 0x1854-0x1857] has been reserved
[ 0.336705] system 00:05: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.336736] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.336738] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.336768] pnp 00:07: Plug and Play ACPI device, IDs SNYa009 PNP030b (active)
[ 0.336802] pnp 00:08: Plug and Play ACPI device, IDs FOX0015 PNP0f13 (active)
[ 0.349893] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.349896] system 00:09: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.349899] system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.349901] system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.349903] system 00:09: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.349906] system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.349908] system 00:09: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.349910] system 00:09: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.349912] system 00:09: [mem 0xff000000-0xffffffff] has been reserved
[ 0.349915] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.349917] system 00:09: [mem 0xf7fef000-0xf7feffff] has been reserved
[ 0.349919] system 00:09: [mem 0xf7ff0000-0xf7ffffff] has been reserved
[ 0.349922] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.350197] pnp: PnP ACPI: found 10 devices
[ 0.350198] ACPI: bus type PNP unregistered
[ 0.356468] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 0.356471] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 0.356484] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.356485] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.356489] pci 0000:00:1c.0: BAR 15: assigned [mem 0xdf200000-0xdf3fffff 64bit pref]
[ 0.356491] pci 0000:00:1c.0: BAR 13: assigned [io 0x3000-0x3fff]
[ 0.356493] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.356496] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.356500] pci 0000:00:1c.0: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.356503] pci 0000:00:1c.0: bridge window [mem 0xdf200000-0xdf3fffff 64bit pref]
[ 0.356507] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.356509] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
[ 0.356513] pci 0000:00:1c.3: bridge window [mem 0xf7200000-0xf7bfffff]
[ 0.356516] pci 0000:00:1c.3: bridge window [mem 0xf0a00000-0xf13fffff 64bit pref]
[ 0.356521] pci 0000:00:1c.4: PCI bridge to [bus 03]
[ 0.356523] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.356526] pci 0000:00:1c.4: bridge window [mem 0xf6800000-0xf71fffff]
[ 0.356529] pci 0000:00:1c.4: bridge window [mem 0xf0000000-0xf09fffff 64bit pref]
[ 0.356534] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.356536] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.356537] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.356539] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
[ 0.356540] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
[ 0.356541] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
[ 0.356543] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
[ 0.356544] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
[ 0.356545] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
[ 0.356547] pci_bus 0000:00: resource 13 [mem 0xdf200000-0xfeafffff]
[ 0.356548] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 0.356550] pci_bus 0000:01: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 0.356551] pci_bus 0000:01: resource 2 [mem 0xdf200000-0xdf3fffff 64bit pref]
[ 0.356553] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.356554] pci_bus 0000:02: resource 1 [mem 0xf7200000-0xf7bfffff]
[ 0.356555] pci_bus 0000:02: resource 2 [mem 0xf0a00000-0xf13fffff 64bit pref]
[ 0.356557] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
[ 0.356558] pci_bus 0000:03: resource 1 [mem 0xf6800000-0xf71fffff]
[ 0.356559] pci_bus 0000:03: resource 2 [mem 0xf0000000-0xf09fffff 64bit pref]
[ 0.356585] NET: Registered protocol family 2
[ 0.356724] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.356813] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.356873] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.356888] TCP: reno registered
[ 0.356895] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.356909] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.356952] NET: Registered protocol family 1
[ 0.356960] pci 0000:00:02.0: Boot video device
[ 0.357196] PCI: CLS 64 bytes, default 64
[ 0.357224] Unpacking initramfs...
[ 0.407590] Freeing initrd memory: 3056K (ffff8800379f8000 - ffff880037cf4000)
[ 0.407595] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.407597] software IO TLB [mem 0xd6898000-0xda898000] (64MB) mapped at [ffff8800d6898000-ffff8800da897fff]
[ 0.407733] Scanning for low memory corruption every 60 seconds
[ 0.407940] audit: initializing netlink socket (disabled)
[ 0.407949] type=2000 audit(1390584362.399:1): initialized
[ 0.419223] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.420210] zbud: loaded
[ 0.420353] VFS: Disk quotas dquot_6.5.2
[ 0.420384] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.420510] msgmni has been set to 7724
[ 0.420720] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.420750] io scheduler noop registered
[ 0.420751] io scheduler deadline registered
[ 0.420772] io scheduler cfq registered (default)
[ 0.421077] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.421091] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.421125] vesafb: mode is 1920x1080x32, linelength=7680, pages=0
[ 0.421126] vesafb: scrolling: redraw
[ 0.421128] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.421958] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90004800000, using 8128k, total 8128k
[ 0.526303] pci_bus 0000:01: Allocating resources
[ 0.526317] pci_bus 0000:02: Allocating resources
[ 0.526325] pci_bus 0000:03: Allocating resources
[ 0.526335] pci 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 0.526342] pci 0000:00:00.0: no hotplug settings from platform
[ 0.526343] pci 0000:00:00.0: using default PCI settings
[ 0.526347] pci 0000:00:02.0: no hotplug settings from platform
[ 0.526347] pci 0000:00:02.0: using default PCI settings
[ 0.526351] pci 0000:00:03.0: no hotplug settings from platform
[ 0.526353] pci 0000:00:14.0: no hotplug settings from platform
[ 0.526353] pci 0000:00:14.0: using default PCI settings
[ 0.526359] pci 0000:00:16.0: no hotplug settings from platform
[ 0.526360] pci 0000:00:16.0: using default PCI settings
[ 0.526365] pci 0000:00:1b.0: no hotplug settings from platform
[ 0.526367] pcieport 0000:00:1c.0: no hotplug settings from platform
[ 0.526374] pci 0000:01:00.0: no hotplug settings from platform
[ 0.526376] pcieport 0000:00:1c.3: no hotplug settings from platform
[ 0.526378] pcieport 0000:00:1c.4: no hotplug settings from platform
[ 0.526382] pci 0000:03:00.0: no hotplug settings from platform
[ 0.526384] pci 0000:00:1d.0: no hotplug settings from platform
[ 0.526385] pci 0000:00:1d.0: using default PCI settings
[ 0.526391] pci 0000:00:1f.0: no hotplug settings from platform
[ 0.526392] pci 0000:00:1f.0: using default PCI settings
[ 0.526399] pci 0000:00:1f.3: no hotplug settings from platform
[ 0.526400] pci 0000:00:1f.3: using default PCI settings
[ 0.594158] Console: switching to colour frame buffer device 240x67
[ 0.764658] fb0: VESA VGA frame buffer device
[ 0.764669] intel_idle: MWAIT substates: 0x11142120
[ 0.764670] intel_idle: v0.4 model 0x45
[ 0.764671] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.764812] GHES: HEST is not enabled!
[ 0.764852] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.765178] Linux agpgart interface v0.103
[ 0.765230] i8042: PNP: PS/2 Controller [PNP030b:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.767228] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.767247] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.767317] mousedev: PS/2 mouse device common for all mice
[ 0.767349] rtc_cmos 00:04: RTC can wake from S4
[ 0.767460] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.767485] rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.767492] Intel P-state driver initializing.
[ 0.767499] Intel pstate controlling: cpu 0
[ 0.767512] Intel pstate controlling: cpu 1
[ 0.767521] Intel pstate controlling: cpu 2
[ 0.767534] Intel pstate controlling: cpu 3
[ 0.767632] drop_monitor: Initializing network drop monitor service
[ 0.767691] TCP: cubic registered
[ 0.767762] NET: Registered protocol family 10
[ 0.767892] NET: Registered protocol family 17
[ 0.767899] Key type dns_resolver registered
[ 0.768078] registered taskstats version 1
[ 0.768458] Magic number: 14:948:441
[ 0.768520] rtc_cmos 00:04: setting system clock to 2014-01-24 17:26:03 UTC (1390584363)
[ 0.768563] PM: Hibernation image not present or could not be loaded.
[ 0.769226] Freeing unused kernel memory: 1144K (ffffffff818cb000 - ffffffff819e9000)
[ 0.769227] Write protecting the kernel read-only data: 8192k
[ 0.771461] Freeing unused kernel memory: 1016K (ffff880001502000 - ffff880001600000)
[ 0.772297] Freeing unused kernel memory: 420K (ffff880001797000 - ffff880001800000)
[ 0.779352] systemd-udevd[58]: starting version 208
[ 0.785047] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.797392] ACPI: bus type USB registered
[ 0.797414] usbcore: registered new interface driver usbfs
[ 0.797421] usbcore: registered new interface driver hub
[ 0.797466] usbcore: registered new device driver usb
[ 0.797999] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.799071] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 0.799095] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.799102] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 0.799179] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 0.799199] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
[ 0.799386] ehci-pci: EHCI PCI platform driver
[ 0.799455] SCSI subsystem initialized
[ 0.799607] hub 1-0:1.0: USB hub found
[ 0.799622] hub 1-0:1.0: 9 ports detected
[ 0.800521] libata version 3.00 loaded.
[ 0.800968] ahci 0000:03:00.0: version 3.0
[ 0.800973] pcieport 0000:00:1c.4: driver skip pci_set_master, fix it!
[ 0.801055] ahci 0000:03:00.0: irq 57 for MSI/MSI-X
[ 0.801379] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.801386] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 0.801629] hub 2-0:1.0: USB hub found
[ 0.801641] hub 2-0:1.0: 4 ports detected
[ 0.802611] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 0.802620] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.802628] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 0.802641] ehci-pci 0000:00:1d.0: debug port 2
[ 0.806555] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.806575] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7d1a000
[ 0.812432] ahci 0000:03:00.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 0.812437] ahci 0000:03:00.0: flags: 64bit ncq led clo only pio ccc
[ 0.812628] scsi0 : ahci
[ 0.812693] ata1: SATA max UDMA/133 abar m8192@0xf6810000 port 0xf6810100 irq 57
[ 0.815754] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.815943] hub 3-0:1.0: USB hub found
[ 0.815950] hub 3-0:1.0: 2 ports detected
[ 1.138987] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.139321] ata1.00: ATA-9: SAMSUNG MZHPU128HCGM-00000, UXM6401Q, max UDMA/133
[ 1.139325] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.144409] ata1.00: configured for UDMA/133
[ 1.144657] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZHPU128 UXM6 PQ: 0 ANSI: 5
[ 1.146113] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[ 1.146270] sd 0:0:0:0: [sda] Write Protect is off
[ 1.146275] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.146356] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.146902] sda: sda1 sda2 sda3
[ 1.147316] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.158944] usb 1-1: new full-speed USB device number 2 using xhci_hcd
[ 1.182711] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.193496] usbcore: registered new interface driver usbhid
[ 1.193500] usbhid: USB HID core driver
[ 1.194234] input: Holtek USB Gaming Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/input/input2
[ 1.194309] holtek_mouse 0003:04D9:A067.0001: input,hidraw0: USB HID v1.10 Keyboard [Holtek USB Gaming Mouse] on usb-0000:00:14.0-1/input0
[ 1.194319] holtek_mouse 0003:04D9:A067.0002: Fixing up report descriptor
[ 1.196141] input: Holtek USB Gaming Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.1/input/input3
[ 1.196456] holtek_mouse 0003:04D9:A067.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [Holtek USB Gaming Mouse] on usb-0000:00:14.0-1/input1
[ 1.196878] holtek_mouse 0003:04D9:A067.0003: hiddev0,hidraw2: USB HID v1.10 Device [Holtek USB Gaming Mouse] on usb-0000:00:14.0-1/input2
[ 1.338940] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 1.408820] tsc: Refined TSC clocksource calibration: 2294.688 MHz
[ 1.512165] usb 1-3: new full-speed USB device number 4 using xhci_hcd
[ 1.530066] input: eGalax Inc. eGalaxTouch EXC7910-1031-12.00.03 as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/input/input4
[ 1.530235] hid-multitouch 0003:0EEF:A108.0004: input,hiddev0,hidraw3: USB HID v2.10 Device [eGalax Inc. eGalaxTouch EXC7910-1031-12.00.03] on usb-0000:00:14.0-3/input0
[ 1.688734] usb 1-5: new high-speed USB device number 5 using xhci_hcd
[ 1.901948] usb 1-6: new full-speed USB device number 6 using xhci_hcd
[ 2.021826] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 2.145681] hub 3-1:1.0: USB hub found
[ 2.145760] hub 3-1:1.0: 8 ports detected
[ 2.408347] Switched to clocksource tsc
[ 31.345489] ata1.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen
[ 31.346708] ata1.00: failed command: READ FPDMA QUEUED
[ 31.347389] ata1.00: cmd 60/08:00:18:34:e9/00:00:02:00:00/40 tag 0 ncq 4096 in
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 31.348976] ata1.00: status: { DRDY }
[ 31.349377] ata1.00: failed command: READ FPDMA QUEUED
[ 31.349939] ata1.00: cmd 60/08:08:77:29:54/00:00:02:00:00/40 tag 1 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 31.351514] ata1.00: status: { DRDY }
[ 31.351915] ata1.00: failed command: READ FPDMA QUEUED
[ 31.352479] ata1.00: cmd 60/08:10:b8:29:54/00:00:02:00:00/40 tag 2 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 31.354077] ata1.00: status: { DRDY }
[ 31.354479] ata1: hard resetting link
[ 31.678660] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 31.684167] ata1.00: configured for UDMA/133
[ 31.684174] ata1.00: device reported invalid CHS sector 0
[ 31.684176] ata1.00: device reported invalid CHS sector 0
[ 31.684178] ata1.00: device reported invalid CHS sector 0
[ 31.684201] ata1: EH complete
[ 62.314918] ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 62.316149] ata1.00: failed command: READ FPDMA QUEUED
[ 62.316812] ata1.00: cmd 60/08:00:00:37:e9/00:00:02:00:00/40 tag 0 ncq 4096 in
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 62.318399] ata1.00: status: { DRDY }
[ 62.318799] ata1.00: failed command: READ FPDMA QUEUED
[ 62.319361] ata1.00: cmd 60/08:08:b0:2c:54/00:00:02:00:00/40 tag 1 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 62.320933] ata1.00: status: { DRDY }
[ 62.321334] ata1: hard resetting link
[ 62.644766] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 62.650110] ata1.00: configured for UDMA/133
[ 62.650116] ata1.00: device reported invalid CHS sector 0
[ 62.650119] ata1.00: device reported invalid CHS sector 0
[ 62.650139] ata1: EH complete
[ 93.337663] ata1.00: exception Emask 0x0 SAct 0x38 SErr 0x0 action 0x6 frozen
[ 93.338882] ata1.00: failed command: READ FPDMA QUEUED
[ 93.339687] ata1.00: cmd 60/08:18:4f:00:00/00:00:00:00:00/40 tag 3 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 93.341450] ata1.00: status: { DRDY }
[ 93.341861] ata1.00: failed command: READ FPDMA QUEUED
[ 93.342423] ata1.00: cmd 60/a8:20:67:01:00/00:00:00:00:00/40 tag 4 ncq 86016 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 93.344007] ata1.00: status: { DRDY }
[ 93.344408] ata1.00: failed command: READ FPDMA QUEUED
[ 93.344971] ata1.00: cmd 60/30:28:0f:02:00/00:00:00:00:00/40 tag 5 ncq 24576 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 93.346555] ata1.00: status: { DRDY }
[ 93.346957] ata1: hard resetting link
[ 93.670838] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 93.676247] ata1.00: configured for UDMA/133
[ 93.676255] ata1.00: device reported invalid CHS sector 0
[ 93.676257] ata1.00: device reported invalid CHS sector 0
[ 93.676259] ata1.00: device reported invalid CHS sector 0
[ 93.676282] ata1: EH complete
[ 93.686876] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 124.360434] ata1.00: NCQ disabled due to excessive errors
[ 124.360439] ata1.00: exception Emask 0x0 SAct 0x7ff00003 SErr 0x0 action 0x6 frozen
[ 124.361725] ata1.00: failed command: READ FPDMA QUEUED
[ 124.362498] ata1.00: cmd 60/08:00:3f:02:c0/00:00:00:00:00/40 tag 0 ncq 4096 in
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.364214] ata1.00: status: { DRDY }
[ 124.364614] ata1.00: failed command: READ FPDMA QUEUED
[ 124.365177] ata1.00: cmd 60/08:08:3f:01:c0/00:00:00:00:00/40 tag 1 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.366753] ata1.00: status: { DRDY }
[ 124.367154] ata1.00: failed command: READ FPDMA QUEUED
[ 124.367717] ata1.00: cmd 60/08:a0:e7:01:c0/00:00:00:00:00/40 tag 20 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.369300] ata1.00: status: { DRDY }
[ 124.369700] ata1.00: failed command: READ FPDMA QUEUED
[ 124.370263] ata1.00: cmd 60/08:a8:ef:01:c0/00:00:00:00:00/40 tag 21 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.371849] ata1.00: status: { DRDY }
[ 124.372249] ata1.00: failed command: READ FPDMA QUEUED
[ 124.372811] ata1.00: cmd 60/08:b0:f7:01:c0/00:00:00:00:00/40 tag 22 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.374396] ata1.00: status: { DRDY }
[ 124.374796] ata1.00: failed command: READ FPDMA QUEUED
[ 124.375357] ata1.00: cmd 60/08:b8:ff:01:c0/00:00:00:00:00/40 tag 23 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.376941] ata1.00: status: { DRDY }
[ 124.377342] ata1.00: failed command: READ FPDMA QUEUED
[ 124.377904] ata1.00: cmd 60/08:c0:07:02:c0/00:00:00:00:00/40 tag 24 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.379488] ata1.00: status: { DRDY }
[ 124.379888] ata1.00: failed command: READ FPDMA QUEUED
[ 124.380452] ata1.00: cmd 60/08:c8:0f:02:c0/00:00:00:00:00/40 tag 25 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.448312] ata1.00: status: { DRDY }
[ 124.481867] ata1.00: failed command: READ FPDMA QUEUED
[ 124.515807] ata1.00: cmd 60/08:d0:17:02:c0/00:00:00:00:00/40 tag 26 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.583914] ata1.00: status: { DRDY }
[ 124.617736] ata1.00: failed command: READ FPDMA QUEUED
[ 124.651626] ata1.00: cmd 60/08:d8:1f:02:c0/00:00:00:00:00/40 tag 27 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.719780] ata1.00: status: { DRDY }
[ 124.753483] ata1.00: failed command: READ FPDMA QUEUED
[ 124.787434] ata1.00: cmd 60/08:e0:27:02:c0/00:00:00:00:00/40 tag 28 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.855720] ata1.00: status: { DRDY }
[ 124.889475] ata1.00: failed command: READ FPDMA QUEUED
[ 124.923145] ata1.00: cmd 60/08:e8:2f:02:c0/00:00:00:00:00/40 tag 29 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 124.991051] ata1.00: status: { DRDY }
[ 125.024712] ata1.00: failed command: READ FPDMA QUEUED
[ 125.058534] ata1.00: cmd 60/08:f0:37:02:c0/00:00:00:00:00/40 tag 30 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 125.126745] ata1.00: status: { DRDY }
[ 125.160422] ata1: hard resetting link
[ 125.486470] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 125.491949] ata1.00: configured for UDMA/133
[ 125.491955] ata1.00: device reported invalid CHS sector 0
[ 125.491957] ata1.00: device reported invalid CHS sector 0
[ 125.491960] ata1.00: device reported invalid CHS sector 0
[ 125.491962] ata1.00: device reported invalid CHS sector 0
[ 125.491963] ata1.00: device reported invalid CHS sector 0
[ 125.491965] ata1.00: device reported invalid CHS sector 0
[ 125.491967] ata1.00: device reported invalid CHS sector 0
[ 125.491968] ata1.00: device reported invalid CHS sector 0
[ 125.491970] ata1.00: device reported invalid CHS sector 0
[ 125.491972] ata1.00: device reported invalid CHS sector 0
[ 125.491973] ata1.00: device reported invalid CHS sector 0
[ 125.491975] ata1.00: device reported invalid CHS sector 0
[ 125.491977] ata1.00: device reported invalid CHS sector 0
[ 125.491985] sd 0:0:0:0: [sda]
[ 125.491987] Result: hostbyte=0x00 driverbyte=0x08
[ 125.491989] sd 0:0:0:0: [sda]
[ 125.491990] Sense Key : 0xb [current] [descriptor]
[ 125.491993] Descriptor sense data with sense descriptors (in hex):
[ 125.491995] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.492003] 00 00 00 00
[ 125.492006] sd 0:0:0:0: [sda]
[ 125.492007] ASC=0x0 ASCQ=0x0
[ 125.492009] sd 0:0:0:0: [sda] CDB:
[ 125.492011] cdb[0]=0x28: 28 00 00 c0 02 3f 00 00 08 00
[ 125.492018] end_request: I/O error, dev sda, sector 12583487
[ 125.525741] sd 0:0:0:0: [sda]
[ 125.525743] Result: hostbyte=0x00 driverbyte=0x08
[ 125.525745] sd 0:0:0:0: [sda]
[ 125.525746] Sense Key : 0xb [current] [descriptor]
[ 125.525748] Descriptor sense data with sense descriptors (in hex):
[ 125.525749] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.525757] 00 00 00 00
[ 125.525761] sd 0:0:0:0: [sda]
[ 125.525762] ASC=0x0 ASCQ=0x0
[ 125.525764] sd 0:0:0:0: [sda] CDB:
[ 125.525765] cdb[0]=0x28: 28 00 00 c0 01 e7 00 00 08 00
[ 125.525771] end_request: I/O error, dev sda, sector 12583399
[ 125.559049] sd 0:0:0:0: [sda]
[ 125.559050] Result: hostbyte=0x00 driverbyte=0x08
[ 125.559051] sd 0:0:0:0: [sda]
[ 125.559052] Sense Key : 0xb [current] [descriptor]
[ 125.559054] Descriptor sense data with sense descriptors (in hex):
[ 125.559055] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.559062] 00 00 00 00
[ 125.559065] sd 0:0:0:0: [sda]
[ 125.559066] ASC=0x0 ASCQ=0x0
[ 125.559067] sd 0:0:0:0: [sda] CDB:
[ 125.559068] cdb[0]=0x28: 28 00 00 c0 01 ef 00 00 08 00
[ 125.559074] end_request: I/O error, dev sda, sector 12583407
[ 125.591752] sd 0:0:0:0: [sda]
[ 125.591753] Result: hostbyte=0x00 driverbyte=0x08
[ 125.591754] sd 0:0:0:0: [sda]
[ 125.591755] Sense Key : 0xb [current] [descriptor]
[ 125.591756] Descriptor sense data with sense descriptors (in hex):
[ 125.591757] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.591762] 00 00 00 00
[ 125.591765] sd 0:0:0:0: [sda]
[ 125.591765] ASC=0x0 ASCQ=0x0
[ 125.591766] sd 0:0:0:0: [sda] CDB:
[ 125.591767] cdb[0]=0x28: 28 00 00 c0 01 f7 00 00 08 00
[ 125.591771] end_request: I/O error, dev sda, sector 12583415
[ 125.624366] sd 0:0:0:0: [sda]
[ 125.624368] Result: hostbyte=0x00 driverbyte=0x08
[ 125.624369] sd 0:0:0:0: [sda]
[ 125.624370] Sense Key : 0xb [current] [descriptor]
[ 125.624372] Descriptor sense data with sense descriptors (in hex):
[ 125.624373] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.624379] 00 00 00 00
[ 125.624383] sd 0:0:0:0: [sda]
[ 125.624384] ASC=0x0 ASCQ=0x0
[ 125.624385] sd 0:0:0:0: [sda] CDB:
[ 125.624386] cdb[0]=0x28: 28 00 00 c0 01 ff 00 00 08 00
[ 125.624391] end_request: I/O error, dev sda, sector 12583423
[ 125.656331] sd 0:0:0:0: [sda]
[ 125.656332] Result: hostbyte=0x00 driverbyte=0x08
[ 125.656334] sd 0:0:0:0: [sda]
[ 125.656335] Sense Key : 0xb [current] [descriptor]
[ 125.656336] Descriptor sense data with sense descriptors (in hex):
[ 125.656337] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.656344] 00 00 00 00
[ 125.656347] sd 0:0:0:0: [sda]
[ 125.656348] ASC=0x0 ASCQ=0x0
[ 125.656350] sd 0:0:0:0: [sda] CDB:
[ 125.656351] cdb[0]=0x28: 28 00 00 c0 02 07 00 00 08 00
[ 125.656356] end_request: I/O error, dev sda, sector 12583431
[ 125.687903] sd 0:0:0:0: [sda]
[ 125.687904] Result: hostbyte=0x00 driverbyte=0x08
[ 125.687905] sd 0:0:0:0: [sda]
[ 125.687906] Sense Key : 0xb [current] [descriptor]
[ 125.687907] Descriptor sense data with sense descriptors (in hex):
[ 125.687908] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.687913] 00 00 00 00
[ 125.687916] sd 0:0:0:0: [sda]
[ 125.687916] ASC=0x0 ASCQ=0x0
[ 125.687917] sd 0:0:0:0: [sda] CDB:
[ 125.687918] cdb[0]=0x28: 28 00 00 c0 02 0f 00 00 08 00
[ 125.687922] end_request: I/O error, dev sda, sector 12583439
[ 125.718974] sd 0:0:0:0: [sda]
[ 125.718975] Result: hostbyte=0x00 driverbyte=0x08
[ 125.718976] sd 0:0:0:0: [sda]
[ 125.718977] Sense Key : 0xb [current] [descriptor]
[ 125.718978] Descriptor sense data with sense descriptors (in hex):
[ 125.718979] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.718983] 00 00 00 00
[ 125.718986] sd 0:0:0:0: [sda]
[ 125.718986] ASC=0x0 ASCQ=0x0
[ 125.718987] sd 0:0:0:0: [sda] CDB:
[ 125.718988] cdb[0]=0x28: 28 00 00 c0 02 17 00 00 08 00
[ 125.718992] end_request: I/O error, dev sda, sector 12583447
[ 125.749811] sd 0:0:0:0: [sda]
[ 125.749812] Result: hostbyte=0x00 driverbyte=0x08
[ 125.749813] sd 0:0:0:0: [sda]
[ 125.749813] Sense Key : 0xb [current] [descriptor]
[ 125.749815] Descriptor sense data with sense descriptors (in hex):
[ 125.749815] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.749820] 00 00 00 00
[ 125.749823] sd 0:0:0:0: [sda]
[ 125.749823] ASC=0x0 ASCQ=0x0
[ 125.749825] sd 0:0:0:0: [sda] CDB:
[ 125.749825] cdb[0]=0x28: 28 00 00 c0 02 1f 00 00 08 00
[ 125.749829] end_request: I/O error, dev sda, sector 12583455
[ 125.780191] sd 0:0:0:0: [sda]
[ 125.780192] Result: hostbyte=0x00 driverbyte=0x08
[ 125.780194] sd 0:0:0:0: [sda]
[ 125.780195] Sense Key : 0xb [current] [descriptor]
[ 125.780196] Descriptor sense data with sense descriptors (in hex):
[ 125.780198] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.780204] 00 00 00 00
[ 125.780207] sd 0:0:0:0: [sda]
[ 125.780208] ASC=0x0 ASCQ=0x0
[ 125.780210] sd 0:0:0:0: [sda] CDB:
[ 125.780211] cdb[0]=0x28: 28 00 00 c0 02 27 00 00 08 00
[ 125.780216] end_request: I/O error, dev sda, sector 12583463
[ 125.810208] sd 0:0:0:0: [sda]
[ 125.810210] Result: hostbyte=0x00 driverbyte=0x08
[ 125.810211] sd 0:0:0:0: [sda]
[ 125.810212] Sense Key : 0xb [current] [descriptor]
[ 125.810214] Descriptor sense data with sense descriptors (in hex):
[ 125.810215] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.810223] 00 00 00 00
[ 125.810226] sd 0:0:0:0: [sda]
[ 125.810227] ASC=0x0 ASCQ=0x0
[ 125.810229] sd 0:0:0:0: [sda] CDB:
[ 125.810230] cdb[0]=0x28: 28 00 00 c0 02 2f 00 00 08 00
[ 125.810239] sd 0:0:0:0: [sda]
[ 125.810240] Result: hostbyte=0x00 driverbyte=0x08
[ 125.810242] sd 0:0:0:0: [sda]
[ 125.810243] Sense Key : 0xb [current] [descriptor]
[ 125.810245] Descriptor sense data with sense descriptors (in hex):
[ 125.810246] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 125.810253] 00 00 00 00
[ 125.810257] sd 0:0:0:0: [sda]
[ 125.810258] ASC=0x0 ASCQ=0x0
[ 125.810260] sd 0:0:0:0: [sda] CDB:
[ 125.810261] cdb[0]=0x28: 28 00 00 c0 02 37 00 00 08 00
[ 125.810273] ata1: EH complete
[ 125.855545] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 125.855767] systemd[1]: No hostname configured.
[ 125.855774] systemd[1]: Set hostname to <localhost>.
[ 125.896662] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 125.896723] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 125.896736] systemd[1]: Starting Login Prompts.
[ 125.896747] systemd[1]: Reached target Login Prompts.
[ 125.896757] systemd[1]: Expecting device sys-subsystem-net-devices-wlp1s0.device...
[ 125.896765] systemd[1]: Starting Remote File Systems.
[ 125.896773] systemd[1]: Reached target Remote File Systems.
[ 125.896780] systemd[1]: Expecting device sys-subsystem-net-devices-wlan0.device...
[ 125.896788] systemd[1]: Expecting device sys-subsystem-net-devices-wlp0s20u2.device...
[ 125.896796] systemd[1]: Expecting device sys-subsystem-net-devices-interface_name.device...
[ 125.896805] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 125.896826] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 125.896834] systemd[1]: Starting LVM2 metadata daemon socket.
[ 125.896859] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 125.896867] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 125.896891] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 125.896898] systemd[1]: Starting Delayed Shutdown Socket.
[ 125.896925] systemd[1]: Listening on Delayed Shutdown Socket.
[ 125.896950] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 125.897038] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 125.897049] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 125.897076] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 125.897084] systemd[1]: Starting Paths.
[ 125.897091] systemd[1]: Reached target Paths.
[ 125.897099] systemd[1]: Starting Encrypted Volumes.
[ 125.897106] systemd[1]: Reached target Encrypted Volumes.
[ 125.897114] systemd[1]: Starting Journal Socket.
[ 125.897152] systemd[1]: Listening on Journal Socket.
[ 125.897605] systemd[1]: Starting Apply Kernel Variables...
[ 125.898095] systemd[1]: Mounting Huge Pages File System...
[ 125.899047] systemd[1]: Started Load Kernel Modules.
[ 125.901395] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 125.902589] systemd[1]: Started Set Up Additional Binary Formats.
[ 125.902620] systemd[1]: Mounted FUSE Control File System.
[ 125.902640] systemd[1]: Mounting Debug File System...
[ 125.903016] systemd[1]: Starting Setup Virtual Console...
[ 125.903358] systemd[1]: Mounting Configuration File System...
[ 125.903640] systemd[1]: Mounting POSIX Message Queue File System...
[ 125.903921] systemd[1]: Starting Journal Service...
[ 125.904299] systemd[1]: Started Journal Service.
[ 125.916845] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[ 125.919072] systemd-journald[122]: Vacuuming done, freed 0 bytes
[ 125.959065] systemd-udevd[146]: starting version 208
[ 126.006669] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 126.007045] ACPI: Requesting acpi_cpufreq
[ 126.011801] ACPI Warning: 0x0000000000001828-0x000000000000182f SystemIO conflicts with Region \PMIO 1 (20130725/utaddress-251)
[ 126.011809] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 126.011813] ACPI Warning: 0x0000000000001c30-0x0000000000001c3f SystemIO conflicts with Region \GPRL 1 (20130725/utaddress-251)
[ 126.011817] ACPI Warning: 0x0000000000001c30-0x0000000000001c3f SystemIO conflicts with Region \GPR_ 2 (20130725/utaddress-251)
[ 126.011821] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 126.011823] ACPI Warning: 0x0000000000001c00-0x0000000000001c2f SystemIO conflicts with Region \GPRL 1 (20130725/utaddress-251)
[ 126.011826] ACPI Warning: 0x0000000000001c00-0x0000000000001c2f SystemIO conflicts with Region \GPR_ 2 (20130725/utaddress-251)
[ 126.011829] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 126.011831] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 126.016043] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 126.017806] mei_me 0000:00:16.0: setting latency timer to 64
[ 126.017844] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
[ 126.018168] ACPI: AC Adapter [ADP1] (on-line)
[ 126.018533] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input7
[ 126.018749] ACPI: Lid Switch [LID0]
[ 126.024617] [drm] Initialized drm 1.1.0 20060810
[ 126.025670] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input8
[ 126.025678] ACPI: Power Button [PWRB]
[ 126.027618] ACPI Warning: 0x000000000000f040-0x000000000000f05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130725/utaddress-251)
[ 126.027625] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 126.029104] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
[ 126.039570] sony_laptop: Sony Notebook Control Driver v0.6
[ 126.040271] input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/SNY5001:00/input/input9
[ 126.040323] input: Sony Vaio Jogdial as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/SNY5001:00/input/input10
[ 126.052679] sony_laptop: brightness ignored, must be controlled by ACPI video driver
[ 126.053949] mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
[ 126.057104] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
[ 126.061557] cfg80211: Calling CRDA to update world regulatory domain
[ 126.063932] [drm] Memory usable by graphics device = 2048M
[ 126.063939] checking generic (e0000000 7f0000) vs hw (e0000000 10000000)
[ 126.063941] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 126.063958] Console: switching to colour dummy device 80x25
[ 126.064087] i915 0000:00:02.0: setting latency timer to 64
[ 126.065272] Bluetooth: Core ver 2.16
[ 126.065288] NET: Registered protocol family 31
[ 126.065290] Bluetooth: HCI device and connection manager initialized
[ 126.065297] Bluetooth: HCI socket layer initialized
[ 126.065300] Bluetooth: L2CAP socket layer initialized
[ 126.065306] Bluetooth: SCO socket layer initialized
[ 126.066200] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 126.066203] Copyright(c) 2003-2013 Intel Corporation
[ 126.066234] pcieport 0000:00:1c.0: driver skip pci_set_master, fix it!
[ 126.066379] iwlwifi 0000:01:00.0: irq 60 for MSI/MSI-X
[ 126.066611] media: Linux media interface: v0.10
[ 126.070972] Linux video capture interface: v2.00
[ 126.071925] usbcore: registered new interface driver btusb
[ 126.072283] iwlwifi 0000:01:00.0: loaded firmware version 22.1.7.0 op_mode iwlmvm
[ 126.079665] uvcvideo: Found UVC 1.00 device USB Webcam (0bda:5727)
[ 126.086285] Bluetooth: hci0: read Intel version: 370710018002030d33
[ 126.086289] Bluetooth: hci0: Intel device is already patched. patch num: 33
[ 126.086708] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless N 7260, REV=0x144
[ 126.086756] iwlwifi 0000:01:00.0: L1 Disabled; Enabling L0S
[ 126.086898] iwlwifi 0000:01:00.0: L1 Disabled; Enabling L0S
[ 126.092008] input: USB Webcam as /devices/pci0000:00/0000:00:14.0/usb1/1-5/1-5:1.0/input/input12
[ 126.092641] usbcore: registered new interface driver uvcvideo
[ 126.092643] USB Video Class driver (1.1.1)
[ 126.097370] rtl8192cu: Chip version 0x10
[ 126.099239] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x10
[ 126.101863] i915 0000:00:02.0: irq 61 for MSI/MSI-X
[ 126.101873] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 126.101874] [drm] Driver supports precise vblank timestamp query.
[ 126.101936] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 126.103517] ACPI: Battery Slot [BAT0] (battery present)
[ 126.106435] thermal LNXTHERM:00: registered as thermal_zone0
[ 126.106438] ACPI: Thermal Zone [TZ00] (44 C)
[ 126.113114] ACPI: Battery Slot [BAT1] (battery absent)
[ 126.116315] iTCO_vendor_support: vendor-support=0
[ 126.116847] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 126.116874] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
[ 126.116974] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 126.126547] nfc: nfc_init: NFC Core ver 0.1
[ 126.126568] NET: Registered protocol family 39
[ 126.129879] Probing NFC pn544
[ 126.140325] rtl8192cu: MAC address: 48:02:2a:7e:a6:e6
[ 126.140330] rtl8192cu: Board Type 0
[ 126.140406] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 126.140468] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
[ 126.140647] usbcore: registered new interface driver rtl8192cu
[ 126.141022] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x10
[ 126.143777] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x10
[ 126.145297] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x10
[ 126.145956] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 126.146279] ieee80211 phy1: Selected rate control algorithm 'rtl_rc'
[ 126.146546] rtlwifi: wireless switch is on
[ 126.155037] Adding 4883756k swap on /dev/sda2. Priority:-1 extents:1 across:4883756k SSFS
[ 126.157369] systemd-udevd[150]: renamed network interface wlan0 to wlp0s20u2
[ 126.172432] fbcon: inteldrmfb (fb0) is primary device
[ 126.174020] kvm: disabled by bios
[ 126.191698] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: data=ordered
[ 126.296157] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 126.316113] systemd-udevd[149]: renamed network interface wlan0 to wlp1s0
[ 126.496564] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126800, board id: 2699, fw id: 1401224
[ 126.530856] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input13
[ 127.272221] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 128.108351] Console: switching to colour frame buffer device 240x67
[ 128.113031] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 128.113032] i915 0000:00:02.0: registered panic notifier
[ 128.118797] systemd-journald[122]: Received request to flush runtime journal from PID 1
[ 128.131283] rtl8192cu: MAC auto ON okay!
[ 128.133182] acpi device:29: registered as cooling_device4
[ 128.133807] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 128.133865] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input14
[ 128.133967] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 128.134326] snd_hda_intel 0000:00:03.0: irq 62 for MSI/MSI-X
[ 128.142523] rtl8192cu: Tx queue select: 0x05
[ 128.190200] hda_codec: invalid CONNECT_LIST verb 5[1]:0
[ 128.190258] hda_codec: invalid CONNECT_LIST verb 6[1]:0
[ 128.190324] hda_codec: invalid CONNECT_LIST verb 7[1]:0
[ 128.191848] input: HDA Intel MID HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input17
[ 128.191965] input: HDA Intel MID HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input16
[ 128.192061] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
[ 128.491245] IPv6: ADDRCONF(NETDEV_UP): wlp0s20u2: link is not ready
[ 128.491384] iwlwifi 0000:01:00.0: L1 Disabled; Enabling L0S
[ 128.491528] iwlwifi 0000:01:00.0: L1 Disabled; Enabling L0S
[ 128.502620] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 129.387913] wlp0s20u2: authenticate with 60:33:4b:e3:fe:31
[ 129.409908] wlp0s20u2: send auth to 60:33:4b:e3:fe:31 (try 1/3)
[ 129.415420] wlp0s20u2: authenticated
[ 129.417546] wlp0s20u2: associate with 60:33:4b:e3:fe:31 (try 1/3)
[ 129.426949] wlp0s20u2: RX AssocResp from 60:33:4b:e3:fe:31 (capab=0x1421 status=0 aid=3)
[ 129.426980] wlp0s20u2: associated
[ 129.427017] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s20u2: link becomes ready
[ 132.215759] wlp1s0: authenticate with 28:c6:8e:38:76:40
[ 132.216650] wlp1s0: send auth to 28:c6:8e:38:76:40 (try 1/3)
[ 132.218773] wlp1s0: authenticated
[ 132.219328] wlp1s0: associate with 28:c6:8e:38:76:40 (try 1/3)
[ 132.223547] wlp1s0: RX AssocResp from 28:c6:8e:38:76:40 (capab=0x411 status=0 aid=2)
[ 132.226025] wlp1s0: associated
[ 132.226065] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[ 258.046843] fuse init (API version 7.22)
[ 378.299290] ACPI: \_SB_.PCI0: Bus check notify on _handle_hotplug_event_root
[ 383.308507] PM: Syncing filesystems ... done.
[ 383.316136] PM: Preparing system for mem sleep
[ 383.316489] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 383.318093] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 383.319198] PM: Entering mem sleep
[ 383.319988] Suspending console(s) (use no_console_suspend to debug)
[ 383.320296] wlp1s0: deauthenticating from 28:c6:8e:38:76:40 by local choice (reason=3)
[ 383.363765] wlp0s20u2: deauthenticating from 60:33:4b:e3:fe:31 by local choice (reason=3)
[ 383.410660] cfg80211: Calling CRDA for country: US
[ 383.410789] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 383.411362] sd 0:0:0:0: [sda] Stopping disk
[ 383.446489] mei_me 0000:00:16.0: suspend
[ 383.446519] Removing pn544
[ 383.672813] PM: suspend of devices complete after 352.743 msecs
[ 383.672995] PM: late suspend of devices complete after 0.180 msecs
[ 383.686193] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[ 383.712750] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[ 383.726404] PM: noirq suspend of devices complete after 53.436 msecs
[ 383.726772] ACPI: Preparing to enter system sleep state S3
[ 383.727125] PM: Saving platform NVS memory
[ 383.738495] Disabling non-boot CPUs ...
[ 383.740019] smpboot: CPU 1 is now offline
[ 383.842641] smpboot: CPU 2 is now offline
[ 383.945915] smpboot: CPU 3 is now offline
[ 383.947636] ACPI: Low-level resume complete
[ 383.947694] PM: Restoring platform NVS memory
[ 383.950388] Enabling non-boot CPUs ...
[ 383.950428] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 383.964791] Intel pstate controlling: cpu 1
[ 383.964841] CPU1 is up
[ 383.964859] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 383.979205] Intel pstate controlling: cpu 2
[ 383.979242] CPU2 is up
[ 383.979256] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 383.993602] Intel pstate controlling: cpu 3
[ 383.993638] CPU3 is up
[ 384.000372] ACPI: Waking up from system sleep state S3
[ 384.040063] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 384.080048] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 384.106810] PM: noirq resume of devices complete after 105.593 msecs
[ 384.106933] PM: early resume of devices complete after 0.104 msecs
[ 384.106955] i915 0000:00:02.0: setting latency timer to 64
[ 384.106964] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 384.107040] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
[ 384.107043] snd_hda_intel 0000:00:03.0: irq 59 for MSI/MSI-X
[ 384.107191] snd_hda_intel 0000:00:1b.0: irq 62 for MSI/MSI-X
[ 384.107217] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 384.143506] mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
[ 384.143557] Probing NFC pn544
[ 384.446544] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 384.451776] ata1.00: c

The first thing to do is use smartctl to test the drive. Start with the short test ( smartctl -t short /dev/sdX ), and if it passes run the long test ( ... -t long ... ).

5 second delay when bringing up the SATA interface (HP dm1-3100ev)

Hello everyone,
I am using ArchLinux on a HP dm1-3100ev (aka dm1z). This little machine is equipped with an 80GB Intel X25-M SSD (2nd gen) and boots and runs nice and fast.
However, I just noticed a curious issue, where the SATA interface takes 5.3 seconds to appear. According to dmesg:
dmesg wrote:[ 1.510296] Switching to clocksource tsc
[ 6.856991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.857578] ata1.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102HD, max UDMA/133
[ 6.857585] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 6.858264] ata1.00: configured for UDMA/133
[ 6.858756] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5
[ 6.871132] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.871271] sd 0:0:0:0: [sda] Write Protect is off
[ 6.871276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.871320] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.872158] sda: sda1
[ 6.873464] sd 0:0:0:0: [sda] Attached SCSI disk
This is on linux 2.6.39. Anyone have any ideas why this is and how I can reduce this delay? This is by far the slowest part of the boot sequence right now!
Full dmesg log below:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39-ARCH (tobias@T-POWA-LX) (gcc version 4.6.0 20110603 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jun 6 22:37:55 CEST 2011
[ 0.000000] Command line: root=/dev/disk/by-uuid/3e8701ef-e777-4352-a42c-83dd9f68240a ro nomodeset quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfa3f000 (usable)
[ 0.000000] BIOS-e820: 00000000dfa3f000 - 00000000dfabf000 (reserved)
[ 0.000000] BIOS-e820: 00000000dfabf000 - 00000000dfebf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dfebf000 - 00000000dfef6000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dfef6000 - 00000000dff00000 (usable)
[ 0.000000] BIOS-e820: 00000000dff00000 - 00000000e0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec10000 - 00000000fec11000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000187000000 (usable)
[ 0.000000] BIOS-e820: 0000000187000000 - 000000019f000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: Hewlett-Packard HP Pavilion dm1 Notebook PC /1611, BIOS F.12 04/26/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x187000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 3 base 0DFEBD000 mask FFFFFF000 uncachable
[ 0.000000] 4 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000019f000000 aka 6640M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0xdff00 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fe1b0] fe1b0
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: 0000000000000000-00000000dff00000
[ 0.000000] 0000000000 - 00c0000000 page 1G
[ 0.000000] 00c0000000 - 00dfe00000 page 2M
[ 0.000000] 00dfe00000 - 00dff00000 page 4k
[ 0.000000] kernel direct mapping tables up to dff00000 @ dfefd000-dff00000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000187000000
[ 0.000000] 0100000000 - 0180000000 page 1G
[ 0.000000] 0180000000 - 0187000000 page 2M
[ 0.000000] kernel direct mapping tables up to 187000000 @ 186ffe000-187000000
[ 0.000000] RAMDISK: 37e47000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 00000000dfef5120 00064 (v01 HPQOEM SLIC-MPC 00000003 01000013)
[ 0.000000] ACPI: FACP 00000000dfef4000 000F4 (v04 HPQOEM SLIC-MPC 00000003 ACPI 00040000)
[ 0.000000] ACPI: DSDT 00000000dfee7000 0972F (v01 HP INSYDE F0000000 ACPI 00040000)
[ 0.000000] ACPI: FACS 00000000dfc96000 00040
[ 0.000000] ACPI: HPET 00000000dfef3000 00038 (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 00000000dfef2000 00084 (v02 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 00000000dfef1000 0003C (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT 00000000dfee6000 00028 (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: SLIC 00000000dfee5000 00176 (v01 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000dfee4000 003DE (v01 HP INSYDE 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 00000000dfee2000 012FA (v02 HP INSYDE 00000001 MSFT 04000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000187000000
[ 0.000000] NUMA: Using 63 for the hash shift.
[ 0.000000] Initmem setup node 0 0000000000000000-0000000187000000
[ 0.000000] NODE_DATA [0000000186ff9000 - 0000000186ffdfff]
[ 0.000000] [ffffea0000000000-ffffea00055fffff] PMD -> [ffff880180c00000-ffff880185bfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00187000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000dfa3f
[ 0.000000] 0: 0x000dfef6 -> 0x000dff00
[ 0.000000] 0: 0x00100000 -> 0x00187000
[ 0.000000] On node 0 totalpages: 1468888
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3922 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 897665 pages, LIFO batch:31
[ 0.000000] Normal zone: 7560 pages used for memmap
[ 0.000000] Normal zone: 545400 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dfa3f000 - 00000000dfabf000
[ 0.000000] PM: Registered nosave memory: 00000000dfabf000 - 00000000dfebf000
[ 0.000000] PM: Registered nosave memory: 00000000dfebf000 - 00000000dfef6000
[ 0.000000] PM: Registered nosave memory: 00000000dff00000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fec11000
[ 0.000000] PM: Registered nosave memory: 00000000fec11000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff880186c00000 s83136 r8192 d23360 u524288
[ 0.000000] pcpu-alloc: s83136 r8192 d23360 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1446987
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-uuid/3e8701ef-e777-4352-a42c-83dd9f68240a ro nomodeset quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 5715728k/6406144k available (4022k kernel code, 530592k absent, 159824k reserved, 3332k data, 724k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 47185920 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1596.101 MHz processor.
[ 0.003340] Calibrating delay loop (skipped), value calculated using timer frequency.. 3193.21 BogoMIPS (lpj=5320336)
[ 0.003347] pid_max: default: 32768 minimum: 301
[ 0.003562] Security Framework initialized
[ 0.003572] AppArmor: AppArmor disabled by boot time parameter
[ 0.005092] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.012089] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.014996] Mount-cache hash table entries: 256
[ 0.015789] Initializing cgroup subsys ns
[ 0.015797] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.015802] Initializing cgroup subsys cpuacct
[ 0.015866] Initializing cgroup subsys memory
[ 0.015901] Initializing cgroup subsys devices
[ 0.015905] Initializing cgroup subsys freezer
[ 0.015908] Initializing cgroup subsys net_cls
[ 0.015911] Initializing cgroup subsys blkio
[ 0.016009] tseg: 00dff00000
[ 0.016014] CPU: Physical Processor ID: 0
[ 0.016016] CPU: Processor Core ID: 0
[ 0.016019] mce: CPU supports 6 MCE banks
[ 0.018003] ACPI: Core revision 20110316
[ 0.026713] ftrace: allocating 15966 entries in 63 pages
[ 0.030133] Setting APIC routing to flat
[ 0.030496] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.064116] CPU0: AMD E-350 Processor stepping 00
[ 0.066663] Performance Events: AMD PMU driver.
[ 0.066663] ... version: 0
[ 0.066663] ... bit width: 48
[ 0.066663] ... generic registers: 4
[ 0.066663] ... value mask: 0000ffffffffffff
[ 0.066663] ... max period: 00007fffffffffff
[ 0.066663] ... fixed-purpose events: 0
[ 0.066663] ... event mask: 000000000000000f
[ 0.083498] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.110105] Booting Node 0, Processors #1
[ 0.110114] smpboot cpu 1: start_ip = 9a000
[ 0.206704] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.213374] Brought up 2 CPUs
[ 0.213387] Total of 2 processors activated (6386.16 BogoMIPS).
[ 0.213856] devtmpfs: initialized
[ 0.217207] PM: Registering ACPI NVS region at dfabf000 (4194304 bytes)
[ 0.218611] print_constraints: dummy:
[ 0.218770] NET: Registered protocol family 16
[ 0.219087] Extended Config Space enabled on 0 nodes
[ 0.219123] ACPI: bus type pci registered
[ 0.220109] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.220115] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.230714] PCI: Using configuration type 1 for base access
[ 0.231511] bio: create slab <bio-0> at 0
[ 0.234922] ACPI: EC: Look up EC in DSDT
[ 0.237245] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.241929] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.253590] ACPI: Interpreter enabled
[ 0.253602] ACPI: (supports S0 S3 S4 S5)
[ 0.253650] ACPI: Using IOAPIC for interrupt routing
[ 0.294296] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.294593] ACPI: No dock devices found.
[ 0.294598] HEST: Table not found.
[ 0.294604] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.303828] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.304172] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.304177] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.304182] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.304186] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff]
[ 0.304190] pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff]
[ 0.304194] pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff]
[ 0.304198] pci_root PNP0A08:00: host bridge window [mem 0x000cc000-0x000cffff]
[ 0.304202] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
[ 0.304206] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 0.304210] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 0.304214] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[ 0.304218] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
[ 0.304222] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
[ 0.304226] pci_root PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff]
[ 0.304230] pci_root PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff]
[ 0.304234] pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xf7ffffff]
[ 0.304238] pci_root PNP0A08:00: host bridge window [mem 0xfc000000-0xffffffff]
[ 0.304265] pci 0000:00:00.0: [1022:1510] type 0 class 0x000600
[ 0.304322] pci 0000:00:01.0: [1002:9802] type 0 class 0x000300
[ 0.304337] pci 0000:00:01.0: reg 10: [mem 0xe0000000-0xefffffff pref]
[ 0.304347] pci 0000:00:01.0: reg 14: [io 0x3000-0x30ff]
[ 0.304357] pci 0000:00:01.0: reg 18: [mem 0xf0200000-0xf023ffff]
[ 0.304404] pci 0000:00:01.0: supports D1 D2
[ 0.304435] pci 0000:00:01.1: [1002:1314] type 0 class 0x000403
[ 0.304448] pci 0000:00:01.1: reg 10: [mem 0xf0244000-0xf0247fff]
[ 0.304506] pci 0000:00:01.1: supports D1 D2
[ 0.304585] pci 0000:00:04.0: [1022:1512] type 1 class 0x000604
[ 0.304645] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.304651] pci 0000:00:04.0: PME# disabled
[ 0.304684] pci 0000:00:05.0: [1022:1513] type 1 class 0x000604
[ 0.304743] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[ 0.304748] pci 0000:00:05.0: PME# disabled
[ 0.304811] pci 0000:00:11.0: [1002:4391] type 0 class 0x000106
[ 0.304838] pci 0000:00:11.0: reg 10: [io 0x3118-0x311f]
[ 0.304852] pci 0000:00:11.0: reg 14: [io 0x3124-0x3127]
[ 0.304866] pci 0000:00:11.0: reg 18: [io 0x3110-0x3117]
[ 0.304880] pci 0000:00:11.0: reg 1c: [io 0x3120-0x3123]
[ 0.304893] pci 0000:00:11.0: reg 20: [io 0x3100-0x310f]
[ 0.304907] pci 0000:00:11.0: reg 24: [mem 0xf024e000-0xf024e3ff]
[ 0.304971] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03
[ 0.304990] pci 0000:00:12.0: reg 10: [mem 0xf024d000-0xf024dfff]
[ 0.305084] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03
[ 0.305790] pci 0000:00:12.2: reg 10: [mem 0xf024c000-0xf024c0ff]
[ 0.309643] pci 0000:00:12.2: supports D1 D2
[ 0.309653] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.309661] pci 0000:00:12.2: PME# disabled
[ 0.309703] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03
[ 0.309726] pci 0000:00:13.0: reg 10: [mem 0xf024b000-0xf024bfff]
[ 0.310052] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03
[ 0.310717] pci 0000:00:13.2: reg 10: [mem 0xf024a000-0xf024a0ff]
[ 0.314283] pci 0000:00:13.2: supports D1 D2
[ 0.314293] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.314302] pci 0000:00:13.2: PME# disabled
[ 0.314343] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[ 0.314451] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[ 0.314483] pci 0000:00:14.2: reg 10: [mem 0xf0240000-0xf0243fff 64bit]
[ 0.314560] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.314567] pci 0000:00:14.2: PME# disabled
[ 0.314600] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601
[ 0.314701] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[ 0.314764] pci 0000:00:16.0: [1002:4397] type 0 class 0x000c03
[ 0.314784] pci 0000:00:16.0: reg 10: [mem 0xf0249000-0xf0249fff]
[ 0.314878] pci 0000:00:16.2: [1002:4396] type 0 class 0x000c03
[ 0.315565] pci 0000:00:16.2: reg 10: [mem 0xf0248000-0xf02480ff]
[ 0.319593] pci 0000:00:16.2: supports D1 D2
[ 0.319602] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 0.319611] pci 0000:00:16.2: PME# disabled
[ 0.319653] pci 0000:00:18.0: [1022:1700] type 0 class 0x000600
[ 0.319704] pci 0000:00:18.1: [1022:1701] type 0 class 0x000600
[ 0.319747] pci 0000:00:18.2: [1022:1702] type 0 class 0x000600
[ 0.320021] pci 0000:00:18.3: [1022:1703] type 0 class 0x000600
[ 0.320088] pci 0000:00:18.4: [1022:1704] type 0 class 0x000600
[ 0.320131] pci 0000:00:18.5: [1022:1718] type 0 class 0x000600
[ 0.320174] pci 0000:00:18.6: [1022:1716] type 0 class 0x000600
[ 0.320216] pci 0000:00:18.7: [1022:1719] type 0 class 0x000600
[ 0.320338] pci 0000:01:00.0: [10ec:8168] type 0 class 0x000200
[ 0.320359] pci 0000:01:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.320392] pci 0000:01:00.0: reg 18: [mem 0xf0004000-0xf0004fff 64bit pref]
[ 0.320412] pci 0000:01:00.0: reg 20: [mem 0xf0000000-0xf0003fff 64bit pref]
[ 0.320466] pci 0000:01:00.0: supports D1 D2
[ 0.320470] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.320477] pci 0000:01:00.0: PME# disabled
[ 0.326731] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.326751] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
[ 0.326762] pci 0000:00:04.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.326771] pci 0000:00:04.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.326884] pci 0000:02:00.0: [1814:539f] type 0 class 0x000280
[ 0.326908] pci 0000:02:00.0: reg 10: [mem 0xf0100000-0xf010ffff]
[ 0.333424] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.333437] pci 0000:00:05.0: bridge window [io 0xfffffffffffff000-0x0000] (disabled)
[ 0.333445] pci 0000:00:05.0: bridge window [mem 0xf0100000-0xf01fffff]
[ 0.333454] pci 0000:00:05.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.333600] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
[ 0.333607] pci 0000:00:14.4: bridge window [io 0xf000-0x0000] (disabled)
[ 0.333615] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.333622] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.333627] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.333631] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.333636] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.333640] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
[ 0.333645] pci 0000:00:14.4: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
[ 0.333649] pci 0000:00:14.4: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
[ 0.333653] pci 0000:00:14.4: bridge window [mem 0x000cc000-0x000cffff] (subtractive decode)
[ 0.333657] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[ 0.333662] pci 0000:00:14.4: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[ 0.333666] pci 0000:00:14.4: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[ 0.333670] pci 0000:00:14.4: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[ 0.333675] pci 0000:00:14.4: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
[ 0.333679] pci 0000:00:14.4: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
[ 0.333683] pci 0000:00:14.4: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
[ 0.333688] pci 0000:00:14.4: bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
[ 0.333692] pci 0000:00:14.4: bridge window [mem 0xe0000000-0xf7ffffff] (subtractive decode)
[ 0.333696] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xffffffff] (subtractive decode)
[ 0.333730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.333965] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[ 0.334034] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[ 0.334166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.334455] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.334981] pci0000:00: ACPI _OSC control (0x19) granted
[ 0.346082] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346217] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346353] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346488] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346625] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346714] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346789] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346863] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.347047] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.347068] vgaarb: loaded
[ 0.347225] PCI: Using ACPI for IRQ routing
[ 0.347231] PCI: pci_cache_line_size set to 64 bytes
[ 0.347435] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.347439] reserve RAM buffer: 00000000dfa3f000 - 00000000dfffffff
[ 0.347444] reserve RAM buffer: 00000000dff00000 - 00000000dfffffff
[ 0.347447] reserve RAM buffer: 0000000187000000 - 0000000187ffffff
[ 0.347671] NetLabel: Initializing
[ 0.347675] NetLabel: domain hash size = 128
[ 0.347677] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.347700] NetLabel: unlabeled traffic allowed by default
[ 0.347731] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.347738] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.349771] Switching to clocksource hpet
[ 0.349869] Switched to NOHz mode on CPU #1
[ 0.350046] Switched to NOHz mode on CPU #0
[ 0.357491] pnp: PnP ACPI init
[ 0.357525] ACPI: bus type pnp registered
[ 0.357763] pnp 00:00: [bus 00-ff]
[ 0.357768] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.357772] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.357777] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.357781] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.357785] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.357789] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.357793] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.357797] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.357800] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.357804] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.357808] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.357811] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.357815] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.357818] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.357822] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.357826] pnp 00:00: [mem 0xe0000000-0xf7ffffff window]
[ 0.357829] pnp 00:00: [mem 0xfc000000-0xffffffff window]
[ 0.357833] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.357945] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.358035] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.358039] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.358135] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.358141] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.358147] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.358359] pnp 00:02: [irq 0 disabled]
[ 0.358392] pnp 00:02: [irq 8]
[ 0.358396] pnp 00:02: [mem 0xfed00000-0xfed003ff]
[ 0.358441] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.358562] pnp 00:03: [io 0x0000-0x000f]
[ 0.358566] pnp 00:03: [io 0x0081-0x008f]
[ 0.358570] pnp 00:03: [io 0x00c0-0x00df]
[ 0.358574] pnp 00:03: [dma 4]
[ 0.358630] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.358647] pnp 00:04: [io 0x00f0-0x00fe]
[ 0.358671] pnp 00:04: [irq 13]
[ 0.358734] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.358812] pnp 00:05: [io 0x0070-0x0071]
[ 0.358869] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.358889] pnp 00:06: [io 0x0060]
[ 0.358892] pnp 00:06: [io 0x0064]
[ 0.358901] pnp 00:06: [irq 1]
[ 0.358958] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.358979] pnp 00:07: [irq 12]
[ 0.359045] pnp 00:07: Plug and Play ACPI device, IDs SYN1e3b SYN1e00 SYN0002 PNP0f13 (active)
[ 0.359066] pnp 00:08: [io 0x0010-0x001f]
[ 0.359069] pnp 00:08: [io 0x002e-0x002f]
[ 0.359072] pnp 00:08: [io 0x0072-0x0073]
[ 0.359075] pnp 00:08: [io 0x0080]
[ 0.359078] pnp 00:08: [io 0x00b0-0x00b1]
[ 0.359081] pnp 00:08: [io 0x0092]
[ 0.359084] pnp 00:08: [io 0x0400-0x04cf]
[ 0.359088] pnp 00:08: [io 0x04d0-0x04d1]
[ 0.359091] pnp 00:08: [io 0x04d6]
[ 0.359094] pnp 00:08: [io 0x0680-0x06ff]
[ 0.359097] pnp 00:08: [io 0x077a]
[ 0.359100] pnp 00:08: [io 0x0c00-0x0c01]
[ 0.359102] pnp 00:08: [io 0x0c14]
[ 0.359106] pnp 00:08: [io 0x0c50-0x0c52]
[ 0.359109] pnp 00:08: [io 0x0c6c]
[ 0.359111] pnp 00:08: [io 0x0c6f]
[ 0.359114] pnp 00:08: [io 0x0cd0-0x0cdb]
[ 0.359216] system 00:08: [io 0x0400-0x04cf] has been reserved
[ 0.359221] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.359225] system 00:08: [io 0x04d6] has been reserved
[ 0.359230] system 00:08: [io 0x0680-0x06ff] has been reserved
[ 0.359234] system 00:08: [io 0x077a] has been reserved
[ 0.359238] system 00:08: [io 0x0c00-0x0c01] has been reserved
[ 0.359242] system 00:08: [io 0x0c14] has been reserved
[ 0.359246] system 00:08: [io 0x0c50-0x0c52] has been reserved
[ 0.359251] system 00:08: [io 0x0c6c] has been reserved
[ 0.359255] system 00:08: [io 0x0c6f] has been reserved
[ 0.359259] system 00:08: [io 0x0cd0-0x0cdb] has been reserved
[ 0.359265] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.359348] pnp 00:09: [mem 0x000e0000-0x000fffff]
[ 0.359353] pnp 00:09: [mem 0xffe00000-0xffffffff]
[ 0.359450] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.359456] system 00:09: [mem 0xffe00000-0xffffffff] has been reserved
[ 0.359462] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.361159] pnp 00:0a: [irq 23]
[ 0.361298] pnp 00:0a: Plug and Play ACPI device, IDs HPQ0004 (active)
[ 0.361323] pnp: PnP ACPI: found 11 devices
[ 0.361326] ACPI: ACPI bus type pnp unregistered
[ 0.369286] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.369294] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
[ 0.369300] pci 0000:00:04.0: bridge window [mem disabled]
[ 0.369307] pci 0000:00:04.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.369315] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.369318] pci 0000:00:05.0: bridge window [io disabled]
[ 0.369325] pci 0000:00:05.0: bridge window [mem 0xf0100000-0xf01fffff]
[ 0.369330] pci 0000:00:05.0: bridge window [mem pref disabled]
[ 0.369337] pci 0000:00:14.4: PCI bridge to [bus 03-03]
[ 0.369340] pci 0000:00:14.4: bridge window [io disabled]
[ 0.369362] pci 0000:00:14.4: bridge window [mem disabled]
[ 0.369368] pci 0000:00:14.4: bridge window [mem pref disabled]
[ 0.369400] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.369408] pci 0000:00:04.0: setting latency timer to 64
[ 0.369422] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.369428] pci 0000:00:05.0: setting latency timer to 64
[ 0.369440] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.369444] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.369448] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.369452] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.369456] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.369460] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.369464] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.369468] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.369472] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.369476] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.369480] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.369484] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.369487] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.369491] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.369495] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[ 0.369499] pci_bus 0000:00: resource 19 [mem 0xe0000000-0xf7ffffff]
[ 0.369503] pci_bus 0000:00: resource 20 [mem 0xfc000000-0xffffffff]
[ 0.369507] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.369512] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.369516] pci_bus 0000:02: resource 1 [mem 0xf0100000-0xf01fffff]
[ 0.369520] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
[ 0.369524] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
[ 0.369528] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.369532] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.369535] pci_bus 0000:03: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.369539] pci_bus 0000:03: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.369543] pci_bus 0000:03: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.369547] pci_bus 0000:03: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.369551] pci_bus 0000:03: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.369555] pci_bus 0000:03: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.369559] pci_bus 0000:03: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.369562] pci_bus 0000:03: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.369566] pci_bus 0000:03: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.369570] pci_bus 0000:03: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.369574] pci_bus 0000:03: resource 18 [mem 0x000ec000-0x000effff]
[ 0.369578] pci_bus 0000:03: resource 19 [mem 0xe0000000-0xf7ffffff]
[ 0.369582] pci_bus 0000:03: resource 20 [mem 0xfc000000-0xffffffff]
[ 0.369723] NET: Registered protocol family 2
[ 0.370245] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.373075] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.378850] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.379526] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.379531] TCP reno registered
[ 0.379569] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.379687] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.380300] NET: Registered protocol family 1
[ 0.380331] pci 0000:00:01.0: Boot video device
[ 0.460342] PCI: CLS 64 bytes, default 64
[ 0.460446] Unpacking initramfs...
[ 0.505657] Freeing initrd memory: 1700k freed
[ 0.506819] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.506828] Placing 64MB software IO TLB between ffff8800dba3f000 - ffff8800dfa3f000
[ 0.506832] software IO TLB at phys 0xdba3f000 - 0xdfa3f000
[ 0.506921] Simple Boot Flag at 0x44 set to 0x1
[ 0.507647] audit: initializing netlink socket (disabled)
[ 0.507672] type=2000 audit(1308931391.506:1): initialized
[ 0.509016] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.513968] VFS: Disk quotas dquot_6.5.2
[ 0.514241] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.514554] msgmni has been set to 11166
[ 0.515475] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.515770] io scheduler noop registered
[ 0.515778] io scheduler deadline registered
[ 0.515922] io scheduler cfq registered (default)
[ 0.516411] ERST: Table is not found!
[ 0.516539] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.740924] Linux agpgart interface v0.103
[ 0.741073] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.747470] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.747529] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.747687] mousedev: PS/2 mouse device common for all mice
[ 0.747867] rtc_cmos 00:05: RTC can wake from S4
[ 0.753544] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.767132] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.767186] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 0.767213] cpuidle: using governor ladder
[ 0.767217] cpuidle: using governor menu
[ 0.767576] TCP cubic registered
[ 0.767581] NET: Registered protocol family 17
[ 0.767593] Registering the dns_resolver key type
[ 0.767764] PM: Hibernation image not present or could not be loaded.
[ 0.767778] registered taskstats version 1
[ 0.768843] rtc_cmos 00:05: setting system clock to 2011-06-24 16:03:12 UTC (1308931392)
[ 0.768918] Initializing network drop monitor service
[ 0.771516] Freeing unused kernel memory: 724k freed
[ 0.771916] Write protecting the kernel read-only data: 6144k
[ 0.772631] Freeing unused kernel memory: 56k freed
[ 0.777964] Freeing unused kernel memory: 784k freed
[ 0.815303] udevd[59]: starting version 171
[ 0.987592] SCSI subsystem initialized
[ 1.022258] libata version 3.00 loaded.
[ 1.036343] ahci 0000:00:11.0: version 3.0
[ 1.036385] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.036532] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 1.036539] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 1.037084] scsi0 : ahci
[ 1.037252] ata1: SATA max UDMA/133 abar m1024@0xf024e000 port 0xf024e100 irq 19
[ 1.510277] Refined TSC clocksource calibration: 1596.003 MHz.
[ 1.510296] Switching to clocksource tsc
[ 6.856991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.857578] ata1.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102HD, max UDMA/133
[ 6.857585] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 6.858264] ata1.00: configured for UDMA/133
[ 6.858756] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5
[ 6.871132] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.871271] sd 0:0:0:0: [sda] Write Protect is off
[ 6.871276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.871320] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.872158] sda: sda1
[ 6.873464] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.051357] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 7.707862] udevd[230]: starting version 171
[ 7.759090] ACPI: acpi_idle registered with cpuidle
[ 7.766584] powernow-k8: Found 1 AMD E-350 Processor (2 cpu cores) (version 2.20.00)
[ 7.766662] powernow-k8: 0 : pstate 0 (1600 MHz)
[ 7.766699] powernow-k8: 1 : pstate 1 (1280 MHz)
[ 7.766703] powernow-k8: 2 : pstate 2 (800 MHz)
[ 7.798328] rt5390 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.798437] rt5390 0000:02:00.0: setting latency timer to 64
[ 7.798971] <-- RTMPAllocAdapterBlock, Status=0
[ 7.860369] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 7.860383] ACPI: Power Button [PWRB]
[ 7.860558] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 7.861604] ACPI: Lid Switch [LID]
[ 7.861751] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 7.861761] ACPI: Power Button [PWRF]
[ 7.897248] vboxdrv: Found 2 processor cores.
[ 7.897357] VBoxDrv: dbg - g_abExecMemory=ffffffffa0276360
[ 7.897405] vboxdrv: fAsync=0 offMin=0x35d offMax=0xcf6
[ 7.897484] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 7.897488] vboxdrv: Successfully loaded version 4.0.8_OSE (interface 0x00180000).
[ 7.932205] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 7.934073] ACPI: AC Adapter [AC] (off-line)
[ 7.934370] wmi: Mapper loaded
[ 7.961127] acpi device:02: registered as cooling_device2
[ 7.961272] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 7.961285] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 8.003256] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[ 8.003495] SP5100 TCO timer: mmio address 0xb8fe00 already in use
[ 8.014954] ACPI Warning: For \_TZ_.THRM._AL0: Return Package has no elements (empty) (20110316/nspredef-456)
[ 8.014969] ACPI: [Package] has zero elements (ffff88017c138cc0)
[ 8.014973] ACPI: Invalid active0 threshold
[ 8.025488] thermal LNXTHERM:00: registered as thermal_zone0
[ 8.025495] ACPI: Thermal Zone [THRM] (52 C)
[ 8.044849] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 8.044866] ACPI: Battery Slot [BAT0] (battery present)
[ 8.076882] hp_accel: laptop model unknown, using default axes configuration
[ 8.109541] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8.112918] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 8.112984] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.113075] r8169 0000:01:00.0: setting latency timer to 64
[ 8.113083] r8169 0000:01:00.0: (unregistered net_device): unknown MAC, using family default
[ 8.113141] r8169 0000:01:00.0: irq 40 for MSI/MSI-X
[ 8.113883] r8169 0000:01:00.0: eth0: RTL8168b/8111b at 0xffffc90000c34000, 68:b5:99:e1:fa:b1, XID 0c200000 IRQ 40
[ 8.145250] usbcore: registered new interface driver usbfs
[ 8.145307] usbcore: registered new interface driver hub
[ 8.146258] usbcore: registered new device driver usb
[ 8.147469] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 8.211672] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.211773] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.211870] ehci_hcd 0000:00:12.2: setting latency timer to 64
[ 8.211878] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 8.211930] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 8.226790] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.226839] QUIRK: Enable AMD PLL fix
[ 8.226874] ehci_hcd 0000:00:12.2: debug port 1
[ 8.226916] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf024c000
[ 8.236710] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 8.237083] hub 1-0:1.0: USB hub found
[ 8.237094] hub 1-0:1.0: 5 ports detected
[ 8.237272] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.237336] ehci_hcd 0000:00:13.2: setting latency timer to 64
[ 8.237342] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 8.237361] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 8.246722] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.246777] ehci_hcd 0000:00:13.2: debug port 1
[ 8.246803] ehci_hcd 0000:00:13.2: irq 17, io mem 0xf024a000
[ 8.255280] [drm] Initialized drm 1.1.0 20060810
[ 8.256809] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 8.257138] hub 2-0:1.0: USB hub found
[ 8.257148] hub 2-0:1.0: 5 ports detected
[ 8.257353] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.257432] ehci_hcd 0000:00:16.2: setting latency timer to 64
[ 8.257438] ehci_hcd 0000:00:16.2: EHCI Host Controller
[ 8.257456] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 8.266735] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.266794] ehci_hcd 0000:00:16.2: debug port 1
[ 8.266822] ehci_hcd 0000:00:16.2: irq 17, io mem 0xf0248000
[ 8.280083] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 8.280419] hub 3-0:1.0: USB hub found
[ 8.280429] hub 3-0:1.0: 4 ports detected
[ 8.299920] input: HP WMI hotkeys as /devices/virtual/input/input5
[ 8.368162] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.368219] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.368296] ohci_hcd 0000:00:12.0: setting latency timer to 64
[ 8.368303] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 8.368334] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 8.383583] ohci_hcd 0000:00:12.0: irq 18, io mem 0xf024d000
[ 8.438348] [drm] VGACON disable radeon kernel modesetting.
[ 8.439661] pci 0000:00:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.439670] pci 0000:00:01.0: setting latency timer to 64
[ 8.440157] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 8.440162] [drm] No driver support for vblank timestamp query.
[ 8.440168] [drm] Initialized radeon 1.33.0 20080528 for 0000:00:01.0 on minor 0
[ 8.441308] hub 4-0:1.0: USB hub found
[ 8.441368] hub 4-0:1.0: 5 ports detected
[ 8.441720] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.441833] ohci_hcd 0000:00:13.0: setting latency timer to 64
[ 8.441841] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 8.441860] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 8.456856] ohci_hcd 0000:00:13.0: irq 18, io mem 0xf024b000
[ 8.477927] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 8.477937] Disabling lock debugging due to kernel taint
[ 8.514652] hub 5-0:1.0: USB hub found
[ 8.514713] hub 5-0:1.0: 5 ports detected
[ 8.514902] HDA Intel 0000:00:01.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 8.515007] HDA Intel 0000:00:01.1: irq 41 for MSI/MSI-X
[ 8.515044] HDA Intel 0000:00:01.1: setting latency timer to 64
[ 8.534738] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.534853] HDA Intel 0000:00:14.2: setting latency timer to 64
[ 8.566706] usb 2-1: new high speed USB device number 2 using ehci_hcd
[ 8.583897] [fglrx] Maximum main memory to use for locked dma buffers: 5393 MBytes.
[ 8.583979] [fglrx] vendor: 1002 device: 9802 count: 1
[ 8.584734] [fglrx] ioport: bar 1, base 0x3000, size: 0x100
[ 8.584748] pci 0000:00:01.0: setting latency timer to 64
[ 8.585495] [fglrx] Kernel PAT support is enabled
[ 8.585539] [fglrx] module loaded - fglrx 8.86.5 [May 24 2011] with 1 minors
[ 8.598000] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input6
[ 8.614292] input: HDA ATI SB Mic at Ext Right Jack as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[ 8.614454] input: HDA ATI SB HP Out at Ext Right Jack as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[ 8.614783] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.614861] ohci_hcd 0000:00:16.0: setting latency timer to 64
[ 8.614869] ohci_hcd 0000:00:16.0: OHCI Host Controller
[ 8.614900] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 6
[ 8.623464] ohci_hcd 0000:00:16.0: irq 18, io mem 0xf0249000
[ 8.681124] hub 6-0:1.0: USB hub found
[ 8.681137] hub 6-0:1.0: 4 ports detected
[ 8.892947] Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xe40000/0x5a0400
[ 8.940407] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9
[ 9.016651] lis3lv02d: 8 bits 3DC sensor found
[ 9.403986] Linux media interface: v0.10
[ 9.420636] Linux video capture interface: v2.00
[ 9.429080] uvcvideo: Found UVC 1.00 device HP Webcam-101 (174f:112b)
[ 9.455290] input: HP Webcam-101 as /devices/pci0000:00/0000:00:13.2/usb2/2-1/2-1:1.0/input/input10
[ 9.455419] usbcore: registered new interface driver uvcvideo
[ 9.455423] USB Video Class driver (v1.0.0)
[ 9.460103] usb 2-2: new high speed USB device number 3 using ehci_hcd
[ 9.960350] usb 6-1: new full speed USB device number 2 using ohci_hcd
[ 10.246250] Bluetooth: Core ver 2.16
[ 10.246292] NET: Registered protocol family 31
[ 10.246295] Bluetooth: HCI device and connection manager initialized
[ 10.246300] Bluetooth: HCI socket layer initialized
[ 10.246303] Bluetooth: L2CAP socket layer initialized
[ 10.250254] Bluetooth: SCO socket layer initialized
[ 10.265755] Initializing USB Mass Storage driver...
[ 10.265954] usbcore: registered new interface driver usb-storage
[ 10.265957] USB Mass Storage support registered.
[ 10.270760] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 10.271722] usbcore: registered new interface driver btusb
[ 10.288479] scsi1 : usb-storage 2-2:1.0
[ 10.288755] usbcore: registered new interface driver ums-realtek
[ 10.293708] usbcore: registered new interface driver uas
[ 10.430407] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input11
[ 10.430745] Registered led device: hp::hddprotect
[ 10.430769] hp_accel: driver loaded
[ 10.526540] EXT4-fs (sda1): re-mounted. Opts: discard
[ 11.289737] scsi 1:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 11.290445] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 11.312911] fuse init (API version 7.16)
[ 11.519361] r8169 0000:01:00.0: eth0: link down
[ 11.527370] KH: Use High Memory for Beacon
[ 11.531213] <-- RTMPAllocTxRxRingMemory, Status=0
[ 11.588181] <==== rt28xx_init, Status=0
[ 11.588301] 0x1300 = 00064300
[ 12.021213] sd 1:0:0:0: [sdb] 3987456 512-byte logical blocks: (2.04 GB/1.90 GiB)
[ 12.023162] sd 1:0:0:0: [sdb] Write Protect is off
[ 12.023168] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 12.023172] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.025360] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.027256] sdb: sdb1
[ 12.031613] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.031628] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 12.486029] fglrx_pci 0000:00:01.0: irq 42 for MSI/MSI-X
[ 12.486918] [fglrx] Firegl kernel thread PID: 779
[ 12.486999] [fglrx] Firegl kernel thread PID: 780
[ 12.487080] [fglrx] Firegl kernel thread PID: 781
[ 12.487290] [fglrx] IRQ 42 Enabled
[ 12.612000] [fglrx] Gart USWC size:1280 M.
[ 12.612007] [fglrx] Gart cacheable size:508 M.
[ 12.612017] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 12.612021] [fglrx] Reserved FB block: Unshared offset:fbfd000, size:403000
[ 12.612025] [fglrx] Reserved FB block: Unshared offset:17ff4000, size:c000
[ 25.342715] EXT4-fs (sda1): re-mounted. Opts: discard,commit=600
[ 39.000090] NET: Registered protocol family 10
[ 39.001989] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 39.648846] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.

Hello everyone,
I am using ArchLinux on a HP dm1-3100ev (aka dm1z). This little machine is equipped with an 80GB Intel X25-M SSD (2nd gen) and boots and runs nice and fast.
However, I just noticed a curious issue, where the SATA interface takes 5.3 seconds to appear. According to dmesg:
dmesg wrote:[ 1.510296] Switching to clocksource tsc
[ 6.856991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.857578] ata1.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102HD, max UDMA/133
[ 6.857585] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 6.858264] ata1.00: configured for UDMA/133
[ 6.858756] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5
[ 6.871132] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.871271] sd 0:0:0:0: [sda] Write Protect is off
[ 6.871276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.871320] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.872158] sda: sda1
[ 6.873464] sd 0:0:0:0: [sda] Attached SCSI disk
This is on linux 2.6.39. Anyone have any ideas why this is and how I can reduce this delay? This is by far the slowest part of the boot sequence right now!
Full dmesg log below:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39-ARCH (tobias@T-POWA-LX) (gcc version 4.6.0 20110603 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jun 6 22:37:55 CEST 2011
[ 0.000000] Command line: root=/dev/disk/by-uuid/3e8701ef-e777-4352-a42c-83dd9f68240a ro nomodeset quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfa3f000 (usable)
[ 0.000000] BIOS-e820: 00000000dfa3f000 - 00000000dfabf000 (reserved)
[ 0.000000] BIOS-e820: 00000000dfabf000 - 00000000dfebf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dfebf000 - 00000000dfef6000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dfef6000 - 00000000dff00000 (usable)
[ 0.000000] BIOS-e820: 00000000dff00000 - 00000000e0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec10000 - 00000000fec11000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000187000000 (usable)
[ 0.000000] BIOS-e820: 0000000187000000 - 000000019f000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: Hewlett-Packard HP Pavilion dm1 Notebook PC /1611, BIOS F.12 04/26/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x187000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 3 base 0DFEBD000 mask FFFFFF000 uncachable
[ 0.000000] 4 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000019f000000 aka 6640M
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0xdff00 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fe1b0] fe1b0
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: 0000000000000000-00000000dff00000
[ 0.000000] 0000000000 - 00c0000000 page 1G
[ 0.000000] 00c0000000 - 00dfe00000 page 2M
[ 0.000000] 00dfe00000 - 00dff00000 page 4k
[ 0.000000] kernel direct mapping tables up to dff00000 @ dfefd000-dff00000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000187000000
[ 0.000000] 0100000000 - 0180000000 page 1G
[ 0.000000] 0180000000 - 0187000000 page 2M
[ 0.000000] kernel direct mapping tables up to 187000000 @ 186ffe000-187000000
[ 0.000000] RAMDISK: 37e47000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 00000000dfef5120 00064 (v01 HPQOEM SLIC-MPC 00000003 01000013)
[ 0.000000] ACPI: FACP 00000000dfef4000 000F4 (v04 HPQOEM SLIC-MPC 00000003 ACPI 00040000)
[ 0.000000] ACPI: DSDT 00000000dfee7000 0972F (v01 HP INSYDE F0000000 ACPI 00040000)
[ 0.000000] ACPI: FACS 00000000dfc96000 00040
[ 0.000000] ACPI: HPET 00000000dfef3000 00038 (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 00000000dfef2000 00084 (v02 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 00000000dfef1000 0003C (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT 00000000dfee6000 00028 (v01 HP INSYDE 00000001 ACPI 00040000)
[ 0.000000] ACPI: SLIC 00000000dfee5000 00176 (v01 HPQOEM SLIC-MPC 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000dfee4000 003DE (v01 HP INSYDE 00000001 AMD 00000001)
[ 0.000000] ACPI: SSDT 00000000dfee2000 012FA (v02 HP INSYDE 00000001 MSFT 04000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000187000000
[ 0.000000] NUMA: Using 63 for the hash shift.
[ 0.000000] Initmem setup node 0 0000000000000000-0000000187000000
[ 0.000000] NODE_DATA [0000000186ff9000 - 0000000186ffdfff]
[ 0.000000] [ffffea0000000000-ffffea00055fffff] PMD -> [ffff880180c00000-ffff880185bfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00187000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000dfa3f
[ 0.000000] 0: 0x000dfef6 -> 0x000dff00
[ 0.000000] 0: 0x00100000 -> 0x00187000
[ 0.000000] On node 0 totalpages: 1468888
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3922 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 897665 pages, LIFO batch:31
[ 0.000000] Normal zone: 7560 pages used for memmap
[ 0.000000] Normal zone: 545400 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x43538210 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dfa3f000 - 00000000dfabf000
[ 0.000000] PM: Registered nosave memory: 00000000dfabf000 - 00000000dfebf000
[ 0.000000] PM: Registered nosave memory: 00000000dfebf000 - 00000000dfef6000
[ 0.000000] PM: Registered nosave memory: 00000000dff00000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fec11000
[ 0.000000] PM: Registered nosave memory: 00000000fec11000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff880186c00000 s83136 r8192 d23360 u524288
[ 0.000000] pcpu-alloc: s83136 r8192 d23360 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1446987
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/disk/by-uuid/3e8701ef-e777-4352-a42c-83dd9f68240a ro nomodeset quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 5715728k/6406144k available (4022k kernel code, 530592k absent, 159824k reserved, 3332k data, 724k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 47185920 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1596.101 MHz processor.
[ 0.003340] Calibrating delay loop (skipped), value calculated using timer frequency.. 3193.21 BogoMIPS (lpj=5320336)
[ 0.003347] pid_max: default: 32768 minimum: 301
[ 0.003562] Security Framework initialized
[ 0.003572] AppArmor: AppArmor disabled by boot time parameter
[ 0.005092] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.012089] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.014996] Mount-cache hash table entries: 256
[ 0.015789] Initializing cgroup subsys ns
[ 0.015797] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.015802] Initializing cgroup subsys cpuacct
[ 0.015866] Initializing cgroup subsys memory
[ 0.015901] Initializing cgroup subsys devices
[ 0.015905] Initializing cgroup subsys freezer
[ 0.015908] Initializing cgroup subsys net_cls
[ 0.015911] Initializing cgroup subsys blkio
[ 0.016009] tseg: 00dff00000
[ 0.016014] CPU: Physical Processor ID: 0
[ 0.016016] CPU: Processor Core ID: 0
[ 0.016019] mce: CPU supports 6 MCE banks
[ 0.018003] ACPI: Core revision 20110316
[ 0.026713] ftrace: allocating 15966 entries in 63 pages
[ 0.030133] Setting APIC routing to flat
[ 0.030496] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.064116] CPU0: AMD E-350 Processor stepping 00
[ 0.066663] Performance Events: AMD PMU driver.
[ 0.066663] ... version: 0
[ 0.066663] ... bit width: 48
[ 0.066663] ... generic registers: 4
[ 0.066663] ... value mask: 0000ffffffffffff
[ 0.066663] ... max period: 00007fffffffffff
[ 0.066663] ... fixed-purpose events: 0
[ 0.066663] ... event mask: 000000000000000f
[ 0.083498] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.110105] Booting Node 0, Processors #1
[ 0.110114] smpboot cpu 1: start_ip = 9a000
[ 0.206704] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.213374] Brought up 2 CPUs
[ 0.213387] Total of 2 processors activated (6386.16 BogoMIPS).
[ 0.213856] devtmpfs: initialized
[ 0.217207] PM: Registering ACPI NVS region at dfabf000 (4194304 bytes)
[ 0.218611] print_constraints: dummy:
[ 0.218770] NET: Registered protocol family 16
[ 0.219087] Extended Config Space enabled on 0 nodes
[ 0.219123] ACPI: bus type pci registered
[ 0.220109] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.220115] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.230714] PCI: Using configuration type 1 for base access
[ 0.231511] bio: create slab <bio-0> at 0
[ 0.234922] ACPI: EC: Look up EC in DSDT
[ 0.237245] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.241929] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.253590] ACPI: Interpreter enabled
[ 0.253602] ACPI: (supports S0 S3 S4 S5)
[ 0.253650] ACPI: Using IOAPIC for interrupt routing
[ 0.294296] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.294593] ACPI: No dock devices found.
[ 0.294598] HEST: Table not found.
[ 0.294604] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.303828] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.304172] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.304177] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.304182] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.304186] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff]
[ 0.304190] pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff]
[ 0.304194] pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff]
[ 0.304198] pci_root PNP0A08:00: host bridge window [mem 0x000cc000-0x000cffff]
[ 0.304202] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
[ 0.304206] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
[ 0.304210] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
[ 0.304214] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
[ 0.304218] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
[ 0.304222] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
[ 0.304226] pci_root PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff]
[ 0.304230] pci_root PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff]
[ 0.304234] pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xf7ffffff]
[ 0.304238] pci_root PNP0A08:00: host bridge window [mem 0xfc000000-0xffffffff]
[ 0.304265] pci 0000:00:00.0: [1022:1510] type 0 class 0x000600
[ 0.304322] pci 0000:00:01.0: [1002:9802] type 0 class 0x000300
[ 0.304337] pci 0000:00:01.0: reg 10: [mem 0xe0000000-0xefffffff pref]
[ 0.304347] pci 0000:00:01.0: reg 14: [io 0x3000-0x30ff]
[ 0.304357] pci 0000:00:01.0: reg 18: [mem 0xf0200000-0xf023ffff]
[ 0.304404] pci 0000:00:01.0: supports D1 D2
[ 0.304435] pci 0000:00:01.1: [1002:1314] type 0 class 0x000403
[ 0.304448] pci 0000:00:01.1: reg 10: [mem 0xf0244000-0xf0247fff]
[ 0.304506] pci 0000:00:01.1: supports D1 D2
[ 0.304585] pci 0000:00:04.0: [1022:1512] type 1 class 0x000604
[ 0.304645] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.304651] pci 0000:00:04.0: PME# disabled
[ 0.304684] pci 0000:00:05.0: [1022:1513] type 1 class 0x000604
[ 0.304743] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[ 0.304748] pci 0000:00:05.0: PME# disabled
[ 0.304811] pci 0000:00:11.0: [1002:4391] type 0 class 0x000106
[ 0.304838] pci 0000:00:11.0: reg 10: [io 0x3118-0x311f]
[ 0.304852] pci 0000:00:11.0: reg 14: [io 0x3124-0x3127]
[ 0.304866] pci 0000:00:11.0: reg 18: [io 0x3110-0x3117]
[ 0.304880] pci 0000:00:11.0: reg 1c: [io 0x3120-0x3123]
[ 0.304893] pci 0000:00:11.0: reg 20: [io 0x3100-0x310f]
[ 0.304907] pci 0000:00:11.0: reg 24: [mem 0xf024e000-0xf024e3ff]
[ 0.304971] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03
[ 0.304990] pci 0000:00:12.0: reg 10: [mem 0xf024d000-0xf024dfff]
[ 0.305084] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03
[ 0.305790] pci 0000:00:12.2: reg 10: [mem 0xf024c000-0xf024c0ff]
[ 0.309643] pci 0000:00:12.2: supports D1 D2
[ 0.309653] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.309661] pci 0000:00:12.2: PME# disabled
[ 0.309703] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03
[ 0.309726] pci 0000:00:13.0: reg 10: [mem 0xf024b000-0xf024bfff]
[ 0.310052] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03
[ 0.310717] pci 0000:00:13.2: reg 10: [mem 0xf024a000-0xf024a0ff]
[ 0.314283] pci 0000:00:13.2: supports D1 D2
[ 0.314293] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.314302] pci 0000:00:13.2: PME# disabled
[ 0.314343] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[ 0.314451] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[ 0.314483] pci 0000:00:14.2: reg 10: [mem 0xf0240000-0xf0243fff 64bit]
[ 0.314560] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.314567] pci 0000:00:14.2: PME# disabled
[ 0.314600] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601
[ 0.314701] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[ 0.314764] pci 0000:00:16.0: [1002:4397] type 0 class 0x000c03
[ 0.314784] pci 0000:00:16.0: reg 10: [mem 0xf0249000-0xf0249fff]
[ 0.314878] pci 0000:00:16.2: [1002:4396] type 0 class 0x000c03
[ 0.315565] pci 0000:00:16.2: reg 10: [mem 0xf0248000-0xf02480ff]
[ 0.319593] pci 0000:00:16.2: supports D1 D2
[ 0.319602] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 0.319611] pci 0000:00:16.2: PME# disabled
[ 0.319653] pci 0000:00:18.0: [1022:1700] type 0 class 0x000600
[ 0.319704] pci 0000:00:18.1: [1022:1701] type 0 class 0x000600
[ 0.319747] pci 0000:00:18.2: [1022:1702] type 0 class 0x000600
[ 0.320021] pci 0000:00:18.3: [1022:1703] type 0 class 0x000600
[ 0.320088] pci 0000:00:18.4: [1022:1704] type 0 class 0x000600
[ 0.320131] pci 0000:00:18.5: [1022:1718] type 0 class 0x000600
[ 0.320174] pci 0000:00:18.6: [1022:1716] type 0 class 0x000600
[ 0.320216] pci 0000:00:18.7: [1022:1719] type 0 class 0x000600
[ 0.320338] pci 0000:01:00.0: [10ec:8168] type 0 class 0x000200
[ 0.320359] pci 0000:01:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.320392] pci 0000:01:00.0: reg 18: [mem 0xf0004000-0xf0004fff 64bit pref]
[ 0.320412] pci 0000:01:00.0: reg 20: [mem 0xf0000000-0xf0003fff 64bit pref]
[ 0.320466] pci 0000:01:00.0: supports D1 D2
[ 0.320470] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.320477] pci 0000:01:00.0: PME# disabled
[ 0.326731] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.326751] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
[ 0.326762] pci 0000:00:04.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.326771] pci 0000:00:04.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.326884] pci 0000:02:00.0: [1814:539f] type 0 class 0x000280
[ 0.326908] pci 0000:02:00.0: reg 10: [mem 0xf0100000-0xf010ffff]
[ 0.333424] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.333437] pci 0000:00:05.0: bridge window [io 0xfffffffffffff000-0x0000] (disabled)
[ 0.333445] pci 0000:00:05.0: bridge window [mem 0xf0100000-0xf01fffff]
[ 0.333454] pci 0000:00:05.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.333600] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
[ 0.333607] pci 0000:00:14.4: bridge window [io 0xf000-0x0000] (disabled)
[ 0.333615] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.333622] pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.333627] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.333631] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.333636] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.333640] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
[ 0.333645] pci 0000:00:14.4: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
[ 0.333649] pci 0000:00:14.4: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
[ 0.333653] pci 0000:00:14.4: bridge window [mem 0x000cc000-0x000cffff] (subtractive decode)
[ 0.333657] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[ 0.333662] pci 0000:00:14.4: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[ 0.333666] pci 0000:00:14.4: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[ 0.333670] pci 0000:00:14.4: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[ 0.333675] pci 0000:00:14.4: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
[ 0.333679] pci 0000:00:14.4: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
[ 0.333683] pci 0000:00:14.4: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
[ 0.333688] pci 0000:00:14.4: bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
[ 0.333692] pci 0000:00:14.4: bridge window [mem 0xe0000000-0xf7ffffff] (subtractive decode)
[ 0.333696] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xffffffff] (subtractive decode)
[ 0.333730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.333965] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[ 0.334034] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[ 0.334166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.334455] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.334981] pci0000:00: ACPI _OSC control (0x19) granted
[ 0.346082] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346217] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346353] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346488] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346625] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346714] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346789] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.346863] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
[ 0.347047] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.347068] vgaarb: loaded
[ 0.347225] PCI: Using ACPI for IRQ routing
[ 0.347231] PCI: pci_cache_line_size set to 64 bytes
[ 0.347435] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.347439] reserve RAM buffer: 00000000dfa3f000 - 00000000dfffffff
[ 0.347444] reserve RAM buffer: 00000000dff00000 - 00000000dfffffff
[ 0.347447] reserve RAM buffer: 0000000187000000 - 0000000187ffffff
[ 0.347671] NetLabel: Initializing
[ 0.347675] NetLabel: domain hash size = 128
[ 0.347677] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.347700] NetLabel: unlabeled traffic allowed by default
[ 0.347731] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.347738] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.349771] Switching to clocksource hpet
[ 0.349869] Switched to NOHz mode on CPU #1
[ 0.350046] Switched to NOHz mode on CPU #0
[ 0.357491] pnp: PnP ACPI init
[ 0.357525] ACPI: bus type pnp registered
[ 0.357763] pnp 00:00: [bus 00-ff]
[ 0.357768] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.357772] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.357777] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.357781] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.357785] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.357789] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.357793] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.357797] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.357800] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.357804] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.357808] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.357811] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.357815] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.357818] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.357822] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.357826] pnp 00:00: [mem 0xe0000000-0xf7ffffff window]
[ 0.357829] pnp 00:00: [mem 0xfc000000-0xffffffff window]
[ 0.357833] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.357945] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.358035] pnp 00:01: [mem 0xfec00000-0xfec00fff]
[ 0.358039] pnp 00:01: [mem 0xfee00000-0xfee00fff]
[ 0.358135] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.358141] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.358147] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.358359] pnp 00:02: [irq 0 disabled]
[ 0.358392] pnp 00:02: [irq 8]
[ 0.358396] pnp 00:02: [mem 0xfed00000-0xfed003ff]
[ 0.358441] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.358562] pnp 00:03: [io 0x0000-0x000f]
[ 0.358566] pnp 00:03: [io 0x0081-0x008f]
[ 0.358570] pnp 00:03: [io 0x00c0-0x00df]
[ 0.358574] pnp 00:03: [dma 4]
[ 0.358630] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.358647] pnp 00:04: [io 0x00f0-0x00fe]
[ 0.358671] pnp 00:04: [irq 13]
[ 0.358734] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.358812] pnp 00:05: [io 0x0070-0x0071]
[ 0.358869] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.358889] pnp 00:06: [io 0x0060]
[ 0.358892] pnp 00:06: [io 0x0064]
[ 0.358901] pnp 00:06: [irq 1]
[ 0.358958] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.358979] pnp 00:07: [irq 12]
[ 0.359045] pnp 00:07: Plug and Play ACPI device, IDs SYN1e3b SYN1e00 SYN0002 PNP0f13 (active)
[ 0.359066] pnp 00:08: [io 0x0010-0x001f]
[ 0.359069] pnp 00:08: [io 0x002e-0x002f]
[ 0.359072] pnp 00:08: [io 0x0072-0x0073]
[ 0.359075] pnp 00:08: [io 0x0080]
[ 0.359078] pnp 00:08: [io 0x00b0-0x00b1]
[ 0.359081] pnp 00:08: [io 0x0092]
[ 0.359084] pnp 00:08: [io 0x0400-0x04cf]
[ 0.359088] pnp 00:08: [io 0x04d0-0x04d1]
[ 0.359091] pnp 00:08: [io 0x04d6]
[ 0.359094] pnp 00:08: [io 0x0680-0x06ff]
[ 0.359097] pnp 00:08: [io 0x077a]
[ 0.359100] pnp 00:08: [io 0x0c00-0x0c01]
[ 0.359102] pnp 00:08: [io 0x0c14]
[ 0.359106] pnp 00:08: [io 0x0c50-0x0c52]
[ 0.359109] pnp 00:08: [io 0x0c6c]
[ 0.359111] pnp 00:08: [io 0x0c6f]
[ 0.359114] pnp 00:08: [io 0x0cd0-0x0cdb]
[ 0.359216] system 00:08: [io 0x0400-0x04cf] has been reserved
[ 0.359221] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.359225] system 00:08: [io 0x04d6] has been reserved
[ 0.359230] system 00:08: [io 0x0680-0x06ff] has been reserved
[ 0.359234] system 00:08: [io 0x077a] has been reserved
[ 0.359238] system 00:08: [io 0x0c00-0x0c01] has been reserved
[ 0.359242] system 00:08: [io 0x0c14] has been reserved
[ 0.359246] system 00:08: [io 0x0c50-0x0c52] has been reserved
[ 0.359251] system 00:08: [io 0x0c6c] has been reserved
[ 0.359255] system 00:08: [io 0x0c6f] has been reserved
[ 0.359259] system 00:08: [io 0x0cd0-0x0cdb] has been reserved
[ 0.359265] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.359348] pnp 00:09: [mem 0x000e0000-0x000fffff]
[ 0.359353] pnp 00:09: [mem 0xffe00000-0xffffffff]
[ 0.359450] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.359456] system 00:09: [mem 0xffe00000-0xffffffff] has been reserved
[ 0.359462] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.361159] pnp 00:0a: [irq 23]
[ 0.361298] pnp 00:0a: Plug and Play ACPI device, IDs HPQ0004 (active)
[ 0.361323] pnp: PnP ACPI: found 11 devices
[ 0.361326] ACPI: ACPI bus type pnp unregistered
[ 0.369286] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.369294] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
[ 0.369300] pci 0000:00:04.0: bridge window [mem disabled]
[ 0.369307] pci 0000:00:04.0: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.369315] pci 0000:00:05.0: PCI bridge to [bus 02-02]
[ 0.369318] pci 0000:00:05.0: bridge window [io disabled]
[ 0.369325] pci 0000:00:05.0: bridge window [mem 0xf0100000-0xf01fffff]
[ 0.369330] pci 0000:00:05.0: bridge window [mem pref disabled]
[ 0.369337] pci 0000:00:14.4: PCI bridge to [bus 03-03]
[ 0.369340] pci 0000:00:14.4: bridge window [io disabled]
[ 0.369362] pci 0000:00:14.4: bridge window [mem disabled]
[ 0.369368] pci 0000:00:14.4: bridge window [mem pref disabled]
[ 0.369400] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.369408] pci 0000:00:04.0: setting latency timer to 64
[ 0.369422] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.369428] pci 0000:00:05.0: setting latency timer to 64
[ 0.369440] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.369444] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.369448] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.369452] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.369456] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.369460] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.369464] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.369468] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.369472] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.369476] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.369480] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.369484] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.369487] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.369491] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.369495] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[ 0.369499] pci_bus 0000:00: resource 19 [mem 0xe0000000-0xf7ffffff]
[ 0.369503] pci_bus 0000:00: resource 20 [mem 0xfc000000-0xffffffff]
[ 0.369507] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.369512] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.369516] pci_bus 0000:02: resource 1 [mem 0xf0100000-0xf01fffff]
[ 0.369520] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
[ 0.369524] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
[ 0.369528] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.369532] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.369535] pci_bus 0000:03: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.369539] pci_bus 0000:03: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.369543] pci_bus 0000:03: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.369547] pci_bus 0000:03: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.369551] pci_bus 0000:03: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.369555] pci_bus 0000:03: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.369559] pci_bus 0000:03: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.369562] pci_bus 0000:03: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.369566] pci_bus 0000:03: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.369570] pci_bus 0000:03: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.369574] pci_bus 0000:03: resource 18 [mem 0x000ec000-0x000effff]
[ 0.369578] pci_bus 0000:03: resource 19 [mem 0xe0000000-0xf7ffffff]
[ 0.369582] pci_bus 0000:03: resource 20 [mem 0xfc000000-0xffffffff]
[ 0.369723] NET: Registered protocol family 2
[ 0.370245] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.373075] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.378850] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.379526] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.379531] TCP reno registered
[ 0.379569] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.379687] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.380300] NET: Registered protocol family 1
[ 0.380331] pci 0000:00:01.0: Boot video device
[ 0.460342] PCI: CLS 64 bytes, default 64
[ 0.460446] Unpacking initramfs...
[ 0.505657] Freeing initrd memory: 1700k freed
[ 0.506819] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.506828] Placing 64MB software IO TLB between ffff8800dba3f000 - ffff8800dfa3f000
[ 0.506832] software IO TLB at phys 0xdba3f000 - 0xdfa3f000
[ 0.506921] Simple Boot Flag at 0x44 set to 0x1
[ 0.507647] audit: initializing netlink socket (disabled)
[ 0.507672] type=2000 audit(1308931391.506:1): initialized
[ 0.509016] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.513968] VFS: Disk quotas dquot_6.5.2
[ 0.514241] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.514554] msgmni has been set to 11166
[ 0.515475] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.515770] io scheduler noop registered
[ 0.515778] io scheduler deadline registered
[ 0.515922] io scheduler cfq registered (default)
[ 0.516411] ERST: Table is not found!
[ 0.516539] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.740924] Linux agpgart interface v0.103
[ 0.741073] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.747470] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.747529] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.747687] mousedev: PS/2 mouse device common for all mice
[ 0.747867] rtc_cmos 00:05: RTC can wake from S4
[ 0.753544] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.767132] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.767186] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 0.767213] cpuidle: using governor ladder
[ 0.767217] cpuidle: using governor menu
[ 0.767576] TCP cubic registered
[ 0.767581] NET: Registered protocol family 17
[ 0.767593] Registering the dns_resolver key type
[ 0.767764] PM: Hibernation image not present or could not be loaded.
[ 0.767778] registered taskstats version 1
[ 0.768843] rtc_cmos 00:05: setting system clock to 2011-06-24 16:03:12 UTC (1308931392)
[ 0.768918] Initializing network drop monitor service
[ 0.771516] Freeing unused kernel memory: 724k freed
[ 0.771916] Write protecting the kernel read-only data: 6144k
[ 0.772631] Freeing unused kernel memory: 56k freed
[ 0.777964] Freeing unused kernel memory: 784k freed
[ 0.815303] udevd[59]: starting version 171
[ 0.987592] SCSI subsystem initialized
[ 1.022258] libata version 3.00 loaded.
[ 1.036343] ahci 0000:00:11.0: version 3.0
[ 1.036385] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.036532] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 1.036539] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 1.037084] scsi0 : ahci
[ 1.037252] ata1: SATA max UDMA/133 abar m1024@0xf024e000 port 0xf024e100 irq 19
[ 1.510277] Refined TSC clocksource calibration: 1596.003 MHz.
[ 1.510296] Switching to clocksource tsc
[ 6.856991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.857578] ata1.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102HD, max UDMA/133
[ 6.857585] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 6.858264] ata1.00: configured for UDMA/133
[ 6.858756] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2M080 2CV1 PQ: 0 ANSI: 5
[ 6.871132] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.871271] sd 0:0:0:0: [sda] Write Protect is off
[ 6.871276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.871320] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.872158] sda: sda1
[ 6.873464] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.051357] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 7.707862] udevd[230]: starting version 171
[ 7.759090] ACPI: acpi_idle registered with cpuidle
[ 7.766584] powernow-k8: Found 1 AMD E-350 Processor (2 cpu cores) (version 2.20.00)
[ 7.766662] powernow-k8: 0 : pstate 0 (1600 MHz)
[ 7.766699] powernow-k8: 1 : pstate 1 (1280 MHz)
[ 7.766703] powernow-k8: 2 : pstate 2 (800 MHz)
[ 7.798328] rt5390 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.798437] rt5390 0000:02:00.0: setting latency timer to 64
[ 7.798971] <-- RTMPAllocAdapterBlock, Status=0
[ 7.860369] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 7.860383] ACPI: Power Button [PWRB]
[ 7.860558] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 7.861604] ACPI: Lid Switch [LID]
[ 7.861751] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 7.861761] ACPI: Power Button [PWRF]
[ 7.897248] vboxdrv: Found 2 processor cores.
[ 7.897357] VBoxDrv: dbg - g_abExecMemory=ffffffffa0276360
[ 7.897405] vboxdrv: fAsync=0 offMin=0x35d offMax=0xcf6
[ 7.897484] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 7.897488] vboxdrv: Successfully loaded version 4.0.8_OSE (interface 0x00180000).
[ 7.932205] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 7.934073] ACPI: AC Adapter [AC] (off-line)
[ 7.934370] wmi: Mapper loaded
[ 7.961127] acpi device:02: registered as cooling_device2
[ 7.961272] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 7.961285] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 8.003256] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[ 8.003495] SP5100 TCO timer: mmio address 0xb8fe00 already in use
[ 8.014954] ACPI Warning: For \_TZ_.THRM._AL0: Return Package has no elements (empty) (20110316/nspredef-456)
[ 8.014969] ACPI: [Package] has zero elements (ffff88017c138cc0)
[ 8.014973] ACPI: Invalid active0 threshold
[ 8.025488] thermal LNXTHERM:00: registered as thermal_zone0
[ 8.025495] ACPI: Thermal Zone [THRM] (52 C)
[ 8.044849] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 8.044866] ACPI: Battery Slot [BAT0] (battery present)
[ 8.076882] hp_accel: laptop model unknown, using default axes configuration
[ 8.109541] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 8.112918] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 8.112984] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.113075] r8169 0000:01:00.0: setting latency timer to 64
[ 8.113083] r8169 0000:01:00.0: (unregistered net_device): unknown MAC, using family default
[ 8.113141] r8169 0000:01:00.0: irq 40 for MSI/MSI-X
[ 8.113883] r8169 0000:01:00.0: eth0: RTL8168b/8111b at 0xffffc90000c34000, 68:b5:99:e1:fa:b1, XID 0c200000 IRQ 40
[ 8.145250] usbcore: registered new interface driver usbfs
[ 8.145307] usbcore: registered new interface driver hub
[ 8.146258] usbcore: registered new device driver usb
[ 8.147469] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 8.211672] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.211773] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.211870] ehci_hcd 0000:00:12.2: setting latency timer to 64
[ 8.211878] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 8.211930] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 8.226790] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.226839] QUIRK: Enable AMD PLL fix
[ 8.226874] ehci_hcd 0000:00:12.2: debug port 1
[ 8.226916] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf024c000
[ 8.236710] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 8.237083] hub 1-0:1.0: USB hub found
[ 8.237094] hub 1-0:1.0: 5 ports detected
[ 8.237272] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.237336] ehci_hcd 0000:00:13.2: setting latency timer to 64
[ 8.237342] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 8.237361] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 8.246722] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.246777] ehci_hcd 0000:00:13.2: debug port 1
[ 8.246803] ehci_hcd 0000:00:13.2: irq 17, io mem 0xf024a000
[ 8.255280] [drm] Initialized drm 1.1.0 20060810
[ 8.256809] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 8.257138] hub 2-0:1.0: USB hub found
[ 8.257148] hub 2-0:1.0: 5 ports detected
[ 8.257353] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.257432] ehci_hcd 0000:00:16.2: setting latency timer to 64
[ 8.257438] ehci_hcd 0000:00:16.2: EHCI Host Controller
[ 8.257456] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 8.266735] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 8.266794] ehci_hcd 0000:00:16.2: debug port 1
[ 8.266822] ehci_hcd 0000:00:16.2: irq 17, io mem 0xf0248000
[ 8.280083] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 8.280419] hub 3-0:1.0: USB hub found
[ 8.280429] hub 3-0:1.0: 4 ports detected
[ 8.299920] input: HP WMI hotkeys as /devices/virtual/input/input5
[ 8.368162] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.368219] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.368296] ohci_hcd 0000:00:12.0: setting latency timer to 64
[ 8.368303] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 8.368334] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 8.383583] ohci_hcd 0000:00:12.0: irq 18, io mem 0xf024d000
[ 8.438348] [drm] VGACON disable radeon kernel modesetting.
[ 8.439661] pci 0000:00:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.439670] pci 0000:00:01.0: setting latency timer to 64
[ 8.440157] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 8.440162] [drm] No driver support for vblank timestamp query.
[ 8.440168] [drm] Initialized radeon 1.33.0 20080528 for 0000:00:01.0 on minor 0
[ 8.441308] hub 4-0:1.0: USB hub found
[ 8.441368] hub 4-0:1.0: 5 ports detected
[ 8.441720] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.441833] ohci_hcd 0000:00:13.0: setting latency timer to 64
[ 8.441841] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 8.441860] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 8.456856] ohci_hcd 0000:00:13.0: irq 18, io mem 0xf024b000
[ 8.477927] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 8.477937] Disabling lock debugging due to kernel taint
[ 8.514652] hub 5-0:1.0: USB hub found
[ 8.514713] hub 5-0:1.0: 5 ports detected
[ 8.514902] HDA Intel 0000:00:01.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 8.515007] HDA Intel 0000:00:01.1: irq 41 for MSI/MSI-X
[ 8.515044] HDA Intel 0000:00:01.1: setting latency timer to 64
[ 8.534738] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.534853] HDA Intel 0000:00:14.2: setting latency timer to 64
[ 8.566706] usb 2-1: new high speed USB device number 2 using ehci_hcd
[ 8.583897] [fglrx] Maximum main memory to use for locked dma buffers: 5393 MBytes.
[ 8.583979] [fglrx] vendor: 1002 device: 9802 count: 1
[ 8.584734] [fglrx] ioport: bar 1, base 0x3000, size: 0x100
[ 8.584748] pci 0000:00:01.0: setting latency timer to 64
[ 8.585495] [fglrx] Kernel PAT support is enabled
[ 8.585539] [fglrx] module loaded - fglrx 8.86.5 [May 24 2011] with 1 minors
[ 8.598000] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input6
[ 8.614292] input: HDA ATI SB Mic at Ext Right Jack as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[ 8.614454] input: HDA ATI SB HP Out at Ext Right Jack as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[ 8.614783] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8.614861] ohci_hcd 0000:00:16.0: setting latency timer to 64
[ 8.614869] ohci_hcd 0000:00:16.0: OHCI Host Controller
[ 8.614900] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 6
[ 8.623464] ohci_hcd 0000:00:16.0: irq 18, io mem 0xf0249000
[ 8.681124] hub 6-0:1.0: USB hub found
[ 8.681137] hub 6-0:1.0: 4 ports detected
[ 8.892947] Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xe40000/0x5a0400
[ 8.940407] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9
[ 9.016651] lis3lv02d: 8 bits 3DC sensor found
[ 9.403986] Linux media interface: v0.10
[ 9.420636] Linux video capture interface: v2.00
[ 9.429080] uvcvideo: Found UVC 1.00 device HP Webcam-101 (174f:112b)
[ 9.455290] input: HP Webcam-101 as /devices/pci0000:00/0000:00:13.2/usb2/2-1/2-1:1.0/input/input10
[ 9.455419] usbcore: registered new interface driver uvcvideo
[ 9.455423] USB Video Class driver (v1.0.0)
[ 9.460103] usb 2-2: new high speed USB device number 3 using ehci_hcd
[ 9.960350] usb 6-1: new full speed USB device number 2 using ohci_hcd
[ 10.246250] Bluetooth: Core ver 2.16
[ 10.246292] NET: Registered protocol family 31
[ 10.246295] Bluetooth: HCI device and connection manager initialized
[ 10.246300] Bluetooth: HCI socket layer initialized
[ 10.246303] Bluetooth: L2CAP socket layer initialized
[ 10.250254] Bluetooth: SCO socket layer initialized
[ 10.265755] Initializing USB Mass Storage driver...
[ 10.265954] usbcore: registered new interface driver usb-storage
[ 10.265957] USB Mass Storage support registered.
[ 10.270760] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 10.271722] usbcore: registered new interface driver btusb
[ 10.288479] scsi1 : usb-storage 2-2:1.0
[ 10.288755] usbcore: registered new interface driver ums-realtek
[ 10.293708] usbcore: registered new interface driver uas
[ 10.430407] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input11
[ 10.430745] Registered led device: hp::hddprotect
[ 10.430769] hp_accel: driver loaded
[ 10.526540] EXT4-fs (sda1): re-mounted. Opts: discard
[ 11.289737] scsi 1:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 11.290445] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 11.312911] fuse init (API version 7.16)
[ 11.519361] r8169 0000:01:00.0: eth0: link down
[ 11.527370] KH: Use High Memory for Beacon
[ 11.531213] <-- RTMPAllocTxRxRingMemory, Status=0
[ 11.588181] <==== rt28xx_init, Status=0
[ 11.588301] 0x1300 = 00064300
[ 12.021213] sd 1:0:0:0: [sdb] 3987456 512-byte logical blocks: (2.04 GB/1.90 GiB)
[ 12.023162] sd 1:0:0:0: [sdb] Write Protect is off
[ 12.023168] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 12.023172] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.025360] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.027256] sdb: sdb1
[ 12.031613] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 12.031628] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 12.486029] fglrx_pci 0000:00:01.0: irq 42 for MSI/MSI-X
[ 12.486918] [fglrx] Firegl kernel thread PID: 779
[ 12.486999] [fglrx] Firegl kernel thread PID: 780
[ 12.487080] [fglrx] Firegl kernel thread PID: 781
[ 12.487290] [fglrx] IRQ 42 Enabled
[ 12.612000] [fglrx] Gart USWC size:1280 M.
[ 12.612007] [fglrx] Gart cacheable size:508 M.
[ 12.612017] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 12.612021] [fglrx] Reserved FB block: Unshared offset:fbfd000, size:403000
[ 12.612025] [fglrx] Reserved FB block: Unshared offset:17ff4000, size:c000
[ 25.342715] EXT4-fs (sda1): re-mounted. Opts: discard,commit=600
[ 39.000090] NET: Registered protocol family 10
[ 39.001989] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 39.648846] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.

Windows XP installation problems in SATA HDD

I am trying to install XP Pro from the CD on a new pc, as listed on the sig.
The computer at first started realtek boot agent, but didnt found any HDD, i found this forum and made some changes:
Pre-Raid Bios Tweaks
Standard Cmos Features
The only thing I change here is to enable "32bit transfer mode" whenever I connect new devices to the Intel IDE controller.
Note: Devices attached to the Promise controller and the Intel Raid(when it is enabled) will NOT appear in the standard Cmos page
Advanced Bios Features
Everything on defaults is usually fine except I always change the following for WinXP:
APIC ACPI SCI IRQ - Enabled
Boot Device select is also on this page and you'll be changing it after all the hardware is setup; more later.
Advanced Cipset Features
Confirm that the memory timing "by SPD" is enabled
PNP/PCI Configurations
Clear NVRam option I always set to "YES" before the first boot after making hardware changes. I'm not sure how important this is but I understand that's what you're supposed to do. I believe it forces the motherboard to detect hardware changes. It reverts to "NO" after the reboot.
PCI/IDE Busmaster set to "enabled" to speed things up outside of Windows.
Integrated Peripherals (Before Raid for most flexibilty)
Onboard Promise IDE - Disabled if you have nothing attached to IDE3 and Serial 3&4
ON-Chip IDE Configuration:
Native Mode (Supported by WinXP- Allows all devices connected to IDE 1&2 and Serial 1&2 to be detected)
SATA Only or PATA Only (select the one that you boot XP with)
Keep SATA Active - Yes (if option available)
Keep PATA Active - Yes (if option available)
PATA Channel selection - Both (if option available)
Configure SATA as Raid - No (if option available)
Leave other settings here at default
Note: Some older Bios versions may appear different than above
Frequency/Voltage Control
Dynamic Overclocking - Disabled
Performance Mode - Slow
Dram Frequency - Auto
Adjust CPU Bus - 201 (for "c" type cpu's)
DDR Voltage - 2.65 (minimum for Dual-Channel Mem stability)
AGP Voltage - 1.55
This is a thumbnail at 63% scale, click for full sized image.
Note: some features above may not appear with your Bios
Note: performance & overclocking features can be increased again AFTER the Raid array has been setup and is stable with Windows.
The above text was copy pasted from this forum.
With my hdd allready recognized i started windows xp configuration, kept on going, formatted using NTFS, win config the started copying files for installation, then
gets to a point that says 'This portion of setup has completed successfully, remove
any disks from the A:\ drive, computer will reboot in 15 seconds.'
so it reboots, and it goes through the cycle again.
It reads the CD, asks if I want to setup Windows XP, then this msg appears "there
is already a \windows directory on the C:\ drive, do you want to do a dual
boot, do you want to delete the contents of this folder and install windows there,
or do you want to install to a separate directory", and a link to the microsoft website for advice on dual booting.
It does this over and over and over again.I tried ejecting the XP CD ROM and restarting, but then it
starts up and says "Missng Operating System"
why the heck does XP insist on restarting, only to go through the exact same setup
steps again? What did i do wrong
Thanks in advance
Many thanks.
Really

Thx for the advice, unfortunatly it didnt work, following your advice i didnt touch any key, the following msg appeared"invalid system disk", but before that i had one error(ive been having this error everytime i tried to install this windows xp cd on this new mobo): i made full format(10-20m), the pc started copying files but it stopped at 2% in the gdi32.dll file, saying to check if i had my cd on the drive, retried it 10 times then i ignored it, the next file in line made the same error, i kept ignoring all files(98% left and with same problem) till 100% completion. Meanwhile, and after going by the full format again, got the same error on the gdi32.dll file, this time i retried it a couple times and quited config(F3),rebboted and made the process all over again, this time i didnt formatted, the config made a disk maintainance, forced me to reboot. Booting from cd for the third time, i kept existing format but this time config copied all windows config files till the end, rebooted, touched no keys, got the same feared msg again"Invalid system disk".
Only ideas i have are: bad cd rom drive? bad cd?
All advices are certainly welcome.

ATI 3D Rage LT Pro AGP-133 (Mach64) Xorg DRI

This is where I'll be posting my crazy adventures in getting this AGP card working with DRI (Direct Rendering) in Xorg.
I've done it in Debian Lenny, so, surely it must be possible in Archlinux!
This card is integrated into my PII 400Mhz Micron Trek II Laptop from 1999 era. Supposedly, this is the very first integrated AGP video card used in laptops. Ever. Although, I have my doubts as to Wikipedia's accuracy in this regards because I believe the Trident Cyber 9397 AGP came out sooner. It's one of those questions we may never know the answer to.
I'm new to Arch (coming from debian), so I'd like to take a paragraph and comment on it. What drew me to it is the i686 optimized packages. The first thing I noticed is that I like it's fast boot time. I haven't run bootchart yet, but I can tell it's significantly faster than debian out of the box. Hopefully there's headroom for additional speed tweaks, but that's for later. The second thing I noticed is that it's about 200 megs larger than debian's comparably minimal install. I found that odd, but, oh well.
Anyways, back to Xorg... one of the final hurdles in setting up a linux box. Getting a display working is simple enough, and maybe 12 years ago having any kind of GUI would have been good enough, but not anymore. On older hardware you need DRI in order to play video properly... not to mention run an snes emulator at a decent fps
Note: for mplayer I can actually use -vo xv, since Xorg supports 2D accelleration by default.
I noticed that Arch has a package named xf86-video-mach64 6.8.1-1. I thought to myself, "Can this be? Will I get dri working out of the box with Arch?!" The answer is no. How stupid of me to think that may be true. So, I'll be adding to this post as developments arise in my little quest. Feel free to chime in with helpful knowledge, pats on the head, threats, and/or flames.
So, here's what I have so far... luckily, I have a pretty decent xorg.conf already setup and ready to go for this card... all I need are mach64 drivers, DRI, DRM, and all the other module goodies.
/etc/X11/xorg.conf
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "DontVTSwitch" "true" # causes kernel panic for me
EndSection
Section "Files"
RgbPath "/etc/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc"
EndSection
Section "Module" # most of these load by default
Load "GLcore"
Load "extmod"
Load "xtrap"
Load "dri"
Load "dbe"
Load "record"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 30 - 60
VertRefresh 70 - 90
Modeline "1024x768" 65 1024 1032 1176 1344 768 771 777 806 -hsync -vsync
Modeline "800x600" 36 800 824 896 1024 600 601 603 625
Modeline "640x480" 25.175 640 664 760 800 480 491 493 525
#Modeline "640x400" 25.175 640 664 760 800 400 409 411 450
Modeline "320x200" 12.588 320 336 384 400 200 204 205 225 Doublescan
# Option "Gamma" ".6" # doesn't work
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
Option "probe_sparse" "False" # ? No noticeable effect
Option "lcdblend" "True" # saw in source code
Option "LCDSync" "True"
Option "accel" "True"
Option "crt_display" "false"
Option "composite_sync" "True"
Option "hw_cursor" "True"
#Option "force_pci_mode" "True" # rather use AGP (the default)
Option "dma_mode" "async" # async is best
Option "agp_mode" "2"
Option "agp_size" "64" # Aperture
Option "local_textures" "True" # ? No idea, sounds nice though.
Option "buffer_size" "2"
Option "tv_out" "false"
#Option "tv_standard" # <str>
Option "mmio_cache" "True"# [<bool>]
Option "test_mmio_cache" "false"# [<bool>]
#Option "panel_display" # [<bool>]
#Option "reference_clock" # <freq>
Option "shadow_fb" "False" # Can't shadow accelerated fb, +5 FPS
Option "sw_cursor" "false"
Option "AccelMethod" "XAA" # EXA or XAA (XAA is slightly faster)
#Option "AccelDFS" "True" # saw on interwebz, but seems bogus for this driver
Option "RenderAccel" "True" # sounds hot
Identifier "Card0"
Driver "mach64"
#Option "ForcePCIMode" "True"
#Option "TVOut"
VendorName "ATI Technologies Inc"
BoardName "3D Rage LT Pro AGP-133"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
# SubSection "Display"
# Viewport 0 0
# Depth 1
# EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 4
# EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 8
# EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 15
# EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768" "800x600" "640x480" "320x200"
EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 24
# EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
I can get into X, by typing startx... I get some nice default windows... First thing I notice is that ctrl-alt-backspace does not shutdown X! I have to type exit into a console?! That's a PITA, so I change that by inserting: Option "DontZap" "false" AND Option "XkbOptions" "terminate:ctrl_alt_bksp" AND editing /etc/X11/xinit/xinitrc to add in some lines...
As per the instructions at: http://wiki.archlinux.org/index.php/Xorg (thank you)
[gripe]Whoever was hitting ctrl-alt-backspace by accident... well... I won't say anything bad about anyone... but come on, people. It sure as hell shouldn't be neccessary to have to add multiple lines of code in multiple configuration files to re-enable the feature... Which will probably break anyways once I add a window manager.[/gripe]
So, anyways, here's the errors so far:
Relevant Errors to console:
FATAL: Module mach64 not found.
(EE) [drm] drmOpen failed.
(EE) MACH64(0): [dri] DRIScreenInit Failed.
Relevant Errors in /var/log/Xorg.0.log:
Short story: the fatal error above is due to a failure in loading the mach64 kernel module, which caused the failure of the drm module, which caused
dri to not load, either. So I learned I need to get/find a mach64 kernel module! Using the locate command, I see I don't have a mach64.ko file.
So I found this old thread relating to the subject: http://bbs.archlinux.org/viewtopic.php?id=53071
^^^ which refers to packages that haven't been maintained since january...
PKGBUILD?! What's that? haha... So I learned about it here: http://wiki.archlinux.org/index.php/ABS … ild_System
I found the tarball on AUR for an unnsupported package (the one from february), and looked at the readme.txt
Preinstall:
You need your own kernel with the following options or the kernel from aur: kernel26-nodrm
Please make sure your kernel has been compiled without built in DRM:
Device Drivers --->
Graphics Support --->
< > Direct Rendering Manager (XFree86 4.1.0 and higher DRI support) ---> (CONFIG_DRM=n) Must be disabled.
While you are at it, if your mach64 card is agp: (These agp options are optional but recommended)
Device Drivers --->
Graphics Support --->
<M or *> /dev/agpgart (AGP Support) ---> (CONFIG_AGP=m or CONFIG_AGP=y)
<M or *> YOUR CHIPSET (CONFIG_AGP_**CHIPSET**=m or CONFIG_AGP_**CHIPSET**=y)
For example, my motherboard is via-based:
<*> VIA chipset support (CONFIG_AGP_VIA=y)
The standard arch kernel has DRM, so it will *not* work
If you need pacman -Uf to install, chances are that your drm.ko still is in your kernel directory, meaning that
... meaning what? The text just ends, like a the directions to some lost, sunken treasure... Sounds like I'd have to recompile my kernel. Not a big deal (only a matter of time before I'd do it for fun), but I want to verify that I actually have to. So, I checked the config for the Archlinux kernel and CONFIG_DRM=m... so it's modular... isn't that I want? It's going to have to load drm.ko right?!
I'm going to try building mach64.ko and drm.ko against the kernel headers for the arch kernel and see how it goes...
Update 1:
Ok, it looks like I do, in fact, need to recompile the kernel... or atleast, that's the next thing I'm going to try....
I can currently get glxinfo to report everything's fine... DRI enabled and such... however, glxgears has an abortion.
Update 2:
After recompiling the kernel, I've learned that I didn't have to. The information in the Arch Wiki must be outdated, because there's no reason to recompile to disable the modular support of DRM from the kernel. Anyways, it still doesn't work (of course, I didn't have to recompile)... so the problem is with either the mesa, drm, or dri packages.
SOOOO... I'm going to downgrade until I find a version that works... stay tuned...
More to come!
Last edited by Daemonjax (2009-07-06 00:10:42)

I'm not able to resolve these errors. Maybe someone more knowledgable than I could help... Here's every log I could think of... starting with the good, and ending with the bad:
lspci (everything looks good)
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
***00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:04.0 Multimedia audio controller: ESS Technology ES1978 Maestro 2E (rev 10)
00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:0a.0 CardBus bridge: Texas Instruments PCI1251B
00:0a.1 CardBus bridge: Texas Instruments PCI1251B
***01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro AGP-133 (rev dc)
lsmod (everything looks good)
Module Size Used by
***mach64 43652 2
***drm 94284 3 mach64
snd_seq_dummy 2696 0
snd_seq_oss 31168 0
snd_es1968 26720 0
snd_seq_midi_event 7012 1 snd_seq_oss
gameport 11280 1 snd_es1968
snd_seq 53744 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_ac97_codec 106088 1 snd_es1968
snd_pcm_oss 40352 0
snd_mixer_oss 17540 1 snd_pcm_oss
ac97_bus 1540 1 snd_ac97_codec
snd_pcm 73768 3 snd_es1968,snd_ac97_codec,snd_pcm_oss
snd_timer 21068 2 snd_seq,snd_pcm
snd_page_alloc 8812 2 snd_es1968,snd_pcm
snd_mpu401_uart 7524 1 snd_es1968
usb_storage 51456 0
snd_rawmidi 21824 1 snd_mpu401_uart
pcmcia 36268 0
snd_seq_device 6768 4 snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd 58404 11 snd_seq_oss,snd_es1968,snd_seq,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 6784 1 snd
uhci_hcd 23476 0
ehci_hcd 35824 0
radio_maestro 6500 0
psmouse 59644 0
yenta_socket 25136 2
i2c_piix4 9876 0
v4l2_common 14244 1 radio_maestro
serio_raw 5704 0
intel_agp 27484 1
pcspkr 2404 0
rsrc_nonstatic 12292 1 yenta_socket
pcmcia_core 35128 3 pcmcia,yenta_socket,rsrc_nonstatic
usbcore 149936 4 usb_storage,uhci_hcd,ehci_hcd
i2c_core 22776 2 i2c_piix4,v4l2_common
shpchp 34424 0
sg 27896 0
container 3460 0
videodev 37088 2 radio_maestro,v4l2_common
v4l1_compat 15720 1 videodev
pci_hotplug 28964 1 shpchp
agpgart 32756 2 drm,intel_agp
thermal 13888 0
evdev 10176 6
processor 35864 0
fan 4392 0
button 5588 0
battery 10984 0
ac 4360 0
rtc_cmos 11244 0
rtc_core 18048 1 rtc_cmos
rtc_lib 2500 1 rtc_core
ext4 242244 2
mbcache 7112 1 ext4
jbd2 58108 1 ext4
crc16 1636 1 ext4
sr_mod 16676 0
cdrom 36032 1 sr_mod
sd_mod 27808 4
ata_piix 23112 3
pata_acpi 4228 0
ata_generic 4680 0
libata 168428 3 ata_piix,pata_acpi,ata_generic
floppy 55780 0
scsi_mod 110516 5 usb_storage,sg,sr_mod,sd_mod,libata
dmesg (everything looks good)
agpgart-intel 0000:00:00.0: AGP 1.0 bridge
***agpgart-intel 0000:00:00.0: putting AGP V2 device into 2x mode
pci 0000:01:00.0: putting AGP V2 device into 2x mode
[drm] descriptor ring: cpu addr cc820000, bus addr: 0x18000000
***DMA test succeeded, using asynchronous DMA mode
/var/log/Xorg.0.log (everything as expected)
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.6.1.901 (1.6.2 RC 1)
Release Date: 2009-5-8
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-ARCH i686
Current Operating System: Linux atropos 2.6.30.1-CUSTNODRM #4 SMP PREEMPT Sat Jul 4 23:40:25 EDT 2009 i686
Build Date: 28 June 2009 11:20:52AM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Jul 5 13:22:21 2009
(==) Using config file: "/etc/X11/xorg.conf"
Parse error on line 15 of section Files in file /etc/X11/xorg.conf
Ignoring obsolete keyword "RgbPath".
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) Option "DontVTSwitch" "true"
(**) Option "DontZap" "false"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/misc" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
built-ins
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) Loader magic: 0x640
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(--) PCI:*(0:1:0:0) 1002:4c42:1002:4c42 ATI Technologies Inc 3D Rage LT Pro AGP-133 rev 220, Mem @ 0xfd000000/16777216, 0xfedfe000/4096, I/O @ 0x0000e800/256, BIOS @ 0x????????/131072
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri2" will be loaded by default.
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "xtrap"
(WW) Warning, couldn't open module xtrap
(II) UnloadModule: "xtrap"
(EE) Failed to load module "xtrap" (module does not exist, 0)
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "mach64"
(II) Loading /usr/lib/xorg/modules/drivers//mach64_drv.so
(II) Module mach64: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 6.8.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) MACH64: Driver for ATI Mach64 chipsets
(II) Primary Device is: PCI 01@00:00:0
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(**) MACH64(0): Depth 16, (--) framebuffer bpp 16
(**) MACH64(0): Option "probe_sparse" "False"
(**) MACH64(0): Option "accel" "True"
(**) MACH64(0): Option "crt_display" "false"
(**) MACH64(0): Option "composite_sync" "True"
(**) MACH64(0): Option "hw_cursor" "True"
(**) MACH64(0): Option "dma_mode" "async"
(**) MACH64(0): Option "agp_mode" "2"
(**) MACH64(0): Option "agp_size" "64"
(**) MACH64(0): Option "local_textures" "True"
(**) MACH64(0): Option "buffer_size" "2"
(**) MACH64(0): Option "tv_out" "false"
(**) MACH64(0): Option "mmio_cache" "True"
(**) MACH64(0): Option "test_mmio_cache" "false"
(**) MACH64(0): Option "shadow_fb" "False"
(**) MACH64(0): Option "sw_cursor" "false"
(**) MACH64(0): Option "AccelMethod" "XAA"
(**) MACH64(0): Option "RenderAccel" "True"
(**) MACH64(0): Option "lcdblend" "True"
(**) MACH64(0): Option "lcdsync" "True"
(**) MACH64(0): Using XAA acceleration architecture
(II) MACH64: Mach64 in slot 1:0:0 detected.
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
ABI class: X.Org Video Driver, version 5.0
(II) MACH64(0): Primary V_BIOS segment is: 0xc000
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.1.0
ABI class: X.Org Video Driver, version 5.0
(II) MACH64(0): VESA BIOS detected
(II) MACH64(0): VESA VBE Version 2.0
(II) MACH64(0): VESA VBE Total Mem: 8128 kB
(II) MACH64(0): VESA VBE OEM: ATI MACH64
(II) MACH64(0): VESA VBE OEM Software Rev: 1.0
(II) MACH64(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) MACH64(0): VESA VBE OEM Product: MACH64LP
(II) MACH64(0): VESA VBE OEM Product Rev: 01.00
(II) MACH64(0): VESA VBE DDC supported
(II) MACH64(0): VESA VBE DDC Level none
(II) MACH64(0): VESA VBE DDC transfer in appr. 2 sec.
(II) MACH64(0): VESA VBE DDC read failed
(--) MACH64(0): Panel model LG LP141X2-A.
(II) MACH64(0): BIOS Data: BIOSSize=0xF000, ROMTable=0x010A.
(II) MACH64(0): BIOS Data: ClockTable=0x08A7, FrequencyTable=0x0000.
(II) MACH64(0): BIOS Data: LCDTable=0x0184.
(II) MACH64(0): BIOS Data: VideoTable=0x0000, HardwareTable=0x015A.
(II) MACH64(0): BIOS Data: I2CType=0x0F, Tuner=0x00, Decoder=0x00, Audio=0x0F.
(--) MACH64(0): ATI 3D Rage LT Pro graphics controller detected.
(--) MACH64(0): Chip type 4C42 "LB", version 4, foundry UMC, class 0, revision 0x03.
(--) MACH64(0): AGP bus interface detected; block I/O base is 0xE800.
(--) MACH64(0): ATI Mach64 adapter detected.
(!!) MACH64(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(--) MACH64(0): Internal RAMDAC (subtype 1) detected.
(==) MACH64(0): RGB weight 565
(==) MACH64(0): Default visual is TrueColor
(==) MACH64(0): Using gamma correction (1.0, 1.0, 1.0)
(II) MACH64(0): Using Mach64 accelerator CRTC.
(WW) MACH64(0): Logic error setting operating state for VGA I/O.
(--) MACH64(0): 1024x768 panel (ID 1) detected.
(--) MACH64(0): Panel clock is 65.146 MHz.
(II) MACH64(0): Using digital flat panel interface.
(II) MACH64(0): Storing hardware cursor image at 0xFD7FFC00.
(II) MACH64(0): Using 8 MB linear aperture at 0xFD000000.
(!!) MACH64(0): Virtual resolutions will be limited to 8191 kB
due to linear aperture size and/or placement of hardware cursor image area.
(II) MACH64(0): Using Block 0 MMIO aperture at 0xFEDFE400.
(II) MACH64(0): Using Block 1 MMIO aperture at 0xFEDFE000.
(WW) MACH64(0): Logic error setting operating state for VGA memory aperture.
(II) MACH64(0): MMIO write caching enabled.
(--) MACH64(0): 8192 kB of SGRAM (1:1) detected (using 8191 kB).
(II) MACH64(0): Engine XCLK 79.742 MHz; Refresh rate code 6.
(--) MACH64(0): Internal programmable clock generator detected.
(--) MACH64(0): Reference clock 29.500 MHz.
(WW) MACH64(0): Extraneous XF86Config HorizSync specification(s) ignored.
(!!) MACH64(0): Conflicting XF86Config VertRefresh specification(s) ignored.
(II) MACH64(0): Maximum clock: 200.00 MHz
(II) MACH64(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "576x432" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "640x512" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "640x512" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "640x512" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "896x672" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "896x672" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "928x696" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "928x696" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "960x720" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "960x720" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "700x525" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "700x525" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "960x720" (exceeds panel dimensions)
(II) MACH64(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(--) MACH64(0): Virtual size is 1024x768 (pitch 1024)
(**) MACH64(0): *Mode "1024x768": 65.1 MHz, 48.5 kHz, 60.8 Hz
(II) MACH64(0): Modeline "1024x768"x60.8 65.15 1024 1032 1176 1344 768 770 775 797 -hsync -vsync (48.5 kHz)
(**) MACH64(0): *Mode "800x600": 65.1 MHz, 49.7 kHz, 63.1 Hz
(II) MACH64(0): Modeline "800x600"x63.1 65.15 800 824 928 1088 600 600 603 619 (49.7 kHz)
(**) MACH64(0): *Mode "640x480": 65.1 MHz, 50.9 kHz, 63.5 Hz
(II) MACH64(0): Modeline "640x480"x63.5 65.15 640 672 832 896 480 488 490 514 (50.9 kHz)
(**) MACH64(0): *Mode "320x200": 65.1 MHz, 50.9 kHz, 63.1 Hz (D)
(II) MACH64(0): Modeline "320x200"x63.1 65.15 320 368 528 576 200 203 204 219 doublescan (50.9 kHz)
(**) MACH64(0): Built-in mode "Native panel mode": 65.1 MHz, 62.6 kHz, 81.4 Hz
(II) MACH64(0): Modeline "Native panel mode"x81.4 65.15 1024 1024 1032 1040 768 768 769 770 (62.6 kHz)
(**) MACH64(0): Default mode "832x624": 65.1 MHz, 45.7 kHz, 57.1 Hz
(II) MACH64(0): Modeline "832x624"x57.1 65.15 832 864 952 1232 624 624 627 657 -hsync -vsync (45.7 kHz)
(**) MACH64(0): Default mode "720x400": 65.1 MHz, 48.8 kHz, 60.7 Hz
(II) MACH64(0): Modeline "720x400"x60.7 65.15 720 768 880 1032 400 400 403 435 -hsync +vsync (48.8 kHz)
(**) MACH64(0): Default mode "640x400": 65.1 MHz, 48.8 kHz, 60.8 Hz
(II) MACH64(0): Modeline "640x400"x60.8 65.15 640 688 800 952 400 400 403 434 -hsync +vsync (48.8 kHz)
(**) MACH64(0): Default mode "640x350": 65.1 MHz, 48.8 kHz, 58.0 Hz
(II) MACH64(0): Modeline "640x350"x58.0 65.15 640 688 800 952 350 374 377 422 +hsync -vsync (48.8 kHz)
(**) MACH64(0): Default mode "512x384": 65.1 MHz, 49.7 kHz, 62.7 Hz (D)
(II) MACH64(0): Modeline "512x384"x62.7 65.15 512 528 624 800 384 384 385 396 doublescan +hsync +vsync (49.7 kHz)
(**) MACH64(0): Default mode "512x384": 65.1 MHz, 49.1 kHz, 61.6 Hz (D)
(II) MACH64(0): Modeline "512x384"x61.6 65.15 512 536 672 816 384 384 387 398 doublescan -hsync -vsync (49.1 kHz)
(**) MACH64(0): Default mode "512x384": 65.1 MHz, 48.5 kHz, 60.8 Hz (D)
(II) MACH64(0): Modeline "512x384"x60.8 65.15 512 536 672 832 384 384 387 398 doublescan -hsync -vsync (48.5 kHz)
(**) MACH64(0): Default mode "512x384": 65.1 MHz, 47.3 kHz, 59.3 Hz (D)
(II) MACH64(0): Modeline "512x384"x59.3 65.15 512 560 656 864 384 384 385 399 doublescan +hsync +vsync (47.3 kHz)
(**) MACH64(0): Default mode "512x384": 65.1 MHz, 51.5 kHz, 65.4 Hz (D)
(II) MACH64(0): Modeline "512x384"x65.4 65.15 512 520 696 752 384 384 387 405 interlace doublescan +hsync +vsync (51.5 kHz)
(**) MACH64(0): Default mode "416x312": 65.1 MHz, 45.7 kHz, 57.2 Hz (D)
(II) MACH64(0): Modeline "416x312"x57.2 65.15 416 448 536 816 312 312 313 328 doublescan -hsync -vsync (45.7 kHz)
(**) MACH64(0): Default mode "400x300": 65.1 MHz, 49.7 kHz, 63.2 Hz (D)
(II) MACH64(0): Modeline "400x300"x63.2 65.15 400 424 528 688 300 300 301 309 doublescan +hsync +vsync (49.7 kHz)
(**) MACH64(0): Default mode "400x300": 65.1 MHz, 48.2 kHz, 61.3 Hz (D)
(II) MACH64(0): Modeline "400x300"x61.3 65.15 400 416 528 728 300 300 301 309 doublescan +hsync +vsync (48.2 kHz)
(**) MACH64(0): Default mode "400x300": 65.1 MHz, 48.5 kHz, 61.3 Hz (D)
(II) MACH64(0): Modeline "400x300"x61.3 65.15 400 440 528 720 300 300 301 311 doublescan +hsync +vsync (48.5 kHz)
(**) MACH64(0): Default mode "400x300": 65.1 MHz, 48.2 kHz, 61.1 Hz (D)
(II) MACH64(0): Modeline "400x300"x61.1 65.15 400 448 616 728 300 300 301 310 doublescan +hsync +vsync (48.2 kHz)
(**) MACH64(0): Default mode "400x300": 65.1 MHz, 48.8 kHz, 59.6 Hz (D)
(II) MACH64(0): Modeline "400x300"x59.6 65.15 400 464 632 712 300 313 316 325 doublescan +hsync +vsync (48.8 kHz)
(**) MACH64(0): Default mode "320x240": 65.1 MHz, 50.9 kHz, 63.5 Hz (D)
(II) MACH64(0): Modeline "320x240"x63.5 65.15 320 344 504 576 240 243 244 256 doublescan -hsync -vsync (50.9 kHz)
(**) MACH64(0): Default mode "320x240": 65.1 MHz, 48.5 kHz, 61.9 Hz (D)
(II) MACH64(0): Modeline "320x240"x61.9 65.15 320 344 448 640 240 240 241 247 doublescan -hsync -vsync (48.5 kHz)
(**) MACH64(0): Default mode "320x240": 65.1 MHz, 48.8 kHz, 61.8 Hz (D)
(II) MACH64(0): Modeline "320x240"x61.8 65.15 320 408 504 632 240 240 241 250 doublescan -hsync -vsync (48.8 kHz)
(**) MACH64(0): Default mode "320x240": 65.1 MHz, 48.8 kHz, 61.1 Hz (D)
(II) MACH64(0): Modeline "320x240"x61.1 65.15 320 352 424 632 240 243 244 255 doublescan -hsync -vsync (48.8 kHz)
(**) MACH64(0): Default mode "360x200": 65.1 MHz, 48.8 kHz, 60.7 Hz (D)
(II) MACH64(0): Modeline "360x200"x60.7 65.15 360 408 520 672 200 200 201 217 doublescan -hsync +vsync (48.8 kHz)
(**) MACH64(0): Default mode "320x175": 65.1 MHz, 48.8 kHz, 58.1 Hz (D)
(II) MACH64(0): Modeline "320x175"x58.1 65.15 320 368 480 632 175 187 188 210 doublescan +hsync -vsync (48.8 kHz)
(==) MACH64(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.6.1.901, module version = 1.2.1
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) MACH64(0): I2C bus "Mach64" initialized.
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) MACH64(0): [drm] SAREA 2200+1208: 3408
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) MACH64(0): [drm] Using the DRM lock SAREA also for drawables.
(II) MACH64(0): [drm] framebuffer handle = 0xfd000000
(II) MACH64(0): [drm] added 1 reserved context for kernel
(II) MACH64(0): X context handle = 0x1
(II) MACH64(0): [drm] installed DRM signal handler
(II) MACH64(0): [drm] Will request asynchronous DMA mode
(**) MACH64(0): [agp] Using AGP 2x Mode
(**) MACH64(0): [agp] Using 64 MB AGP aperture
(II) MACH64(0): [agp] Mode 0x1f000203 [AGP 0x8086/0x7190; Card 0x1002/0x4c42]
(II) MACH64(0): [agp] 65536 kB allocated with handle 0x00000001
(II) MACH64(0): [agp] Using 16 kB for DMA descriptor ring
(**) MACH64(0): [drm] Using 2 MB for DMA buffers
(II) MACH64(0): [agp] Using 62464 kB for AGP textures
(II) MACH64(0): [agp] ring handle = 0x18000000
(II) MACH64(0): [agp] Ring mapped at 0xb7089000
(II) MACH64(0): [agp] vertex buffers handle = 0x18004000
(II) MACH64(0): [agp] Vertex buffers mapped at 0xb6e89000
(II) MACH64(0): [agp] AGP texture region handle = 0x18204000
(II) MACH64(0): [agp] AGP Texture region mapped at 0xb3189000
(II) MACH64(0): [drm] register handle = 0xfedfe000
(II) MACH64(0): [dri] Visual configs initialized
(II) MACH64(0): [dri] Block 0 base at 0xfedfe400
(II) MACH64(0): Memory manager initialized to (0,0) (1024,4095)
(II) MACH64(0): Largest offscreen area available: 1024 x 3327
(II) MACH64(0): Will use 1598 kB of offscreen memory for XAA
(II) MACH64(0): Will use back buffer at offset 0x30f800
(II) MACH64(0): Will use depth buffer at offset 0x48f800
(II) MACH64(0): Will use 1985 kB for local textures at offset 0x60f800
(II) MACH64(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Setting up tile and stipple cache:
32 128x128 slots
18 256x256 slots
6 512x512 slots
(==) MACH64(0): Backing store disabled
(==) MACH64(0): Silken mouse enabled
(II) MACH64(0): DPMS enabled
(II) MACH64(0): [DRI] installation complete
(II) MACH64(0): [drm] Added 128 16384 byte DMA buffers
(II) MACH64(0): [drm] Mapped 128 DMA buffers at 0xb2f89000
(II) MACH64(0): [drm] Installed interrupt handler, using IRQ 11
(II) MACH64(0): Direct rendering enabled
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/mach64_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 2.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device TPPS/2 IBM TrackPoint
(**) TPPS/2 IBM TrackPoint: always reports core events
(**) TPPS/2 IBM TrackPoint: Device: "/dev/input/event5"
(II) TPPS/2 IBM TrackPoint: Found 3 mouse buttons
(II) TPPS/2 IBM TrackPoint: Found x and y relative axes
(II) TPPS/2 IBM TrackPoint: Configuring as mouse
(**) TPPS/2 IBM TrackPoint: YAxisMapping: buttons 4 and 5
(**) TPPS/2 IBM TrackPoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "TPPS/2 IBM TrackPoint" (type: MOUSE)
(**) TPPS/2 IBM TrackPoint: (accel) keeping acceleration scheme 1
(**) TPPS/2 IBM TrackPoint: (accel) filter chain progression: 2.00
(**) TPPS/2 IBM TrackPoint: (accel) filter stage 0: 20.00 ms
(**) TPPS/2 IBM TrackPoint: (accel) set acceleration profile 0
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
xorg.conf (I'm very sure the problem is NOT here, but included for sake of completeness)
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "ServerFlags"
Option "DontVTSwitch" "true" # causes kernel panic
Option "DontZap" "false" # disabled by default?!
EndSection
Section "Files"
RgbPath "/etc/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc"
EndSection
Section "Module" # most of these load by default
Load "GLcore"
Load "extmod"
Load "xtrap"
Load "dri"
Load "dbe"
Load "record"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbdOptions" "terminate::ctrl_alt_bksp"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 30 - 60
VertRefresh 70 - 90
Modeline "1024x768" 65 1024 1032 1176 1344 768 771 777 806 -hsync -vsync
Modeline "800x600" 36 800 824 896 1024 600 601 603 625
Modeline "640x480" 25.175 640 664 760 800 480 491 493 525
#Modeline "640x400" 25.175 640 664 760 800 400 409 411 450
Modeline "320x200" 12.588 320 336 384 400 200 204 205 225 Doublescan
# Option "Gamma" ".6" # doesn't work
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
Option "probe_sparse" "False" # ?
Option "lcdblend" "True" # saw in source code
Option "LCDSync" "True"
Option "accel" "True"
Option "crt_display" "false"
Option "composite_sync" "True"
Option "hw_cursor" "True"
#Option "force_pci_mode" "True" # rather use AGP
Option "dma_mode" "async" # async is best
Option "agp_mode" "2"
Option "agp_size" "64" # Aperture
Option "local_textures" "True"# [<bool>]
Option "buffer_size" "2"
Option "tv_out" "false"
#Option "tv_standard" # <str>
Option "mmio_cache" "True"# [<bool>]
Option "test_mmio_cache" "false"# [<bool>]
#Option "panel_display" # [<bool>]
#Option "reference_clock" # <freq>
Option "shadow_fb" "False" # Can't shadow accelerated fb
Option "sw_cursor" "false"
Option "AccelMethod" "XAA" # EXA or XAA (XAA is slightly faster)
#Option "AccelDFS" "True" # saw on internetz
Option "RenderAccel" "True"
Identifier "Card0"
Driver "mach64"
#Option "ForcePCIMode" "True"
#Option "TVOut"
VendorName "ATI Technologies Inc"
BoardName "3D Rage LT Pro AGP-133"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
# SubSection "Display"
# Viewport 0 0
# Depth 1
# EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 4
# EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 8
# EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 15
# EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768" "800x600" "640x480" "320x200"
EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 24
# EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
glxinfo (everything looks good)
name of display: :0.0
display: :0 screen: 0
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_import_context, GLX_EXT_texture_from_pixmap,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_OML_swap_method,
GLX_SGI_swap_control, GLX_SGIS_multisample, GLX_SGIX_fbconfig,
GLX_SGIX_visual_select_group
client glx vendor string: SGI
client glx version string: 1.4
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_allocate_memory,
GLX_MESA_copy_sub_buffer, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_OML_sync_control,
GLX_SGI_make_current_read, GLX_SGI_swap_control, GLX_SGI_video_sync,
GLX_SGIS_multisample, GLX_SGIX_fbconfig, GLX_SGIX_pbuffer,
GLX_SGIX_visual_select_group, GLX_EXT_texture_from_pixmap
GLX version: 1.2
GLX extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_SGI_swap_control,
GLX_SGI_video_sync, GLX_SGIS_multisample, GLX_SGIX_fbconfig,
GLX_SGIX_visual_select_group
OpenGL vendor string: Gareth Hughes, Leif Delgass, José Fonseca
OpenGL renderer string: Mesa DRI Mach64 [Rage Pro] 20051019 AGP 2x x86/MMX
OpenGL version string: 1.2 Mesa 7.4.4
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multisample, GL_ARB_multitexture,
GL_ARB_transpose_matrix, GL_ARB_vertex_buffer_object, GL_ARB_window_pos,
GL_EXT_abgr, GL_EXT_bgra, GL_EXT_blend_color, GL_EXT_blend_logic_op,
GL_EXT_blend_minmax, GL_EXT_blend_subtract, GL_EXT_clip_volume_hint,
GL_EXT_compiled_vertex_array, GL_EXT_convolution, GL_EXT_copy_texture,
GL_EXT_draw_range_elements, GL_EXT_histogram, GL_EXT_packed_pixels,
GL_EXT_polygon_offset, GL_EXT_rescale_normal,
GL_EXT_separate_specular_color, GL_EXT_subtexture, GL_EXT_texture,
GL_EXT_texture3D, GL_EXT_texture_edge_clamp, GL_EXT_texture_object,
GL_EXT_vertex_array, GL_APPLE_packed_pixels, GL_IBM_rasterpos_clip,
GL_MESA_ycbcr_texture, GL_MESA_window_pos, GL_NV_light_max_exponent,
GL_NV_texgen_reflection, GL_OES_read_format, GL_SGI_color_matrix,
GL_SGI_color_table, GL_SGIS_generate_mipmap, GL_SGIS_texture_edge_clamp,
GL_SGIS_texture_lod
16 GLX Visuals
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x21 16 tc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x22 16 dc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x4e 16 tc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x4f 16 tc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x50 16 tc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x51 16 tc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x52 16 tc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x53 16 tc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x54 16 tc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x55 16 dc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x56 16 dc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x57 16 dc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x58 16 dc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x59 16 dc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x5a 16 dc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x5b 16 dc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
16 GLXFBConfigs:
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x3e 0 tc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x3f 0 tc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x40 0 tc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x41 0 tc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x42 0 tc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x43 0 tc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x44 0 tc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x45 0 tc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x46 0 dc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x47 0 dc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x48 0 dc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x49 0 dc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x4a 0 dc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x4b 0 dc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x4c 0 dc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x4d 0 dc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
ldd $path/glxgears (everything looks good, once again)
linux-gate.so.1 => (0xb7f6c000)
libGL.so.1 => /usr/lib/libGL.so.1 (0xb7efb000)
libm.so.6 => /lib/libm.so.6 (0xb7ed5000)
libc.so.6 => /lib/libc.so.6 (0xb7d8d000)
libX11.so.6 => /usr/lib/libX11.so.6 (0xb7c70000)
libXext.so.6 => /usr/lib/libXext.so.6 (0xb7c61000)
libXxf86vm.so.1 => /usr/lib/libXxf86vm.so.1 (0xb7c5c000)
libXdamage.so.1 => /usr/lib/libXdamage.so.1 (0xb7c58000)
libXfixes.so.3 => /usr/lib/libXfixes.so.3 (0xb7c53000)
libX11-xcb.so.1 => /usr/lib/libX11-xcb.so.1 (0xb7c51000)
libxcb-glx.so.0 => /usr/lib/libxcb-glx.so.0 (0xb7c40000)
libxcb.so.1 => /usr/lib/libxcb.so.1 (0xb7c27000)
libdrm.so.2 => /usr/lib/libdrm.so.2 (0xb7c1e000)
libpthread.so.0 => /lib/libpthread.so.0 (0xb7c05000)
libdl.so.2 => /lib/libdl.so.2 (0xb7c01000)
/lib/ld-linux.so.2 (0xb7f6d000)
libXau.so.6 => /usr/lib/libXau.so.6 (0xb7bfe000)
libXdmcp.so.6 => /usr/lib/libXdmcp.so.6 (0xb7bf9000)
librt.so.1 => /lib/librt.so.1 (0xb7bf0000)
name of display: :0.0
display: :0 screen: 0
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_import_context, GLX_EXT_texture_from_pixmap,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_OML_swap_method,
GLX_SGI_swap_control, GLX_SGIS_multisample, GLX_SGIX_fbconfig,
GLX_SGIX_visual_select_group
client glx vendor string: SGI
client glx version string: 1.4
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_allocate_memory,
GLX_MESA_copy_sub_buffer, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_OML_sync_control,
GLX_SGI_make_current_read, GLX_SGI_swap_control, GLX_SGI_video_sync,
GLX_SGIS_multisample, GLX_SGIX_fbconfig, GLX_SGIX_pbuffer,
GLX_SGIX_visual_select_group, GLX_EXT_texture_from_pixmap
GLX version: 1.2
GLX extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_import_context,
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_MESA_swap_control,
GLX_MESA_swap_frame_usage, GLX_OML_swap_method, GLX_SGI_swap_control,
GLX_SGI_video_sync, GLX_SGIS_multisample, GLX_SGIX_fbconfig,
GLX_SGIX_visual_select_group
OpenGL vendor string: Gareth Hughes, Leif Delgass, José Fonseca
OpenGL renderer string: Mesa DRI Mach64 [Rage Pro] 20051019 AGP 2x x86/MMX
OpenGL version string: 1.2 Mesa 7.4.4
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multisample, GL_ARB_multitexture,
GL_ARB_transpose_matrix, GL_ARB_vertex_buffer_object, GL_ARB_window_pos,
GL_EXT_abgr, GL_EXT_bgra, GL_EXT_blend_color, GL_EXT_blend_logic_op,
GL_EXT_blend_minmax, GL_EXT_blend_subtract, GL_EXT_clip_volume_hint,
GL_EXT_compiled_vertex_array, GL_EXT_convolution, GL_EXT_copy_texture,
GL_EXT_draw_range_elements, GL_EXT_histogram, GL_EXT_packed_pixels,
GL_EXT_polygon_offset, GL_EXT_rescale_normal,
GL_EXT_separate_specular_color, GL_EXT_subtexture, GL_EXT_texture,
GL_EXT_texture3D, GL_EXT_texture_edge_clamp, GL_EXT_texture_object,
GL_EXT_vertex_array, GL_APPLE_packed_pixels, GL_IBM_rasterpos_clip,
GL_MESA_ycbcr_texture, GL_MESA_window_pos, GL_NV_light_max_exponent,
GL_NV_texgen_reflection, GL_OES_read_format, GL_SGI_color_matrix,
GL_SGI_color_table, GL_SGIS_generate_mipmap, GL_SGIS_texture_edge_clamp,
GL_SGIS_texture_lod
16 GLX Visuals
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x21 16 tc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x22 16 dc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x4e 16 tc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x4f 16 tc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x50 16 tc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x51 16 tc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x52 16 tc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x53 16 tc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x54 16 tc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x55 16 dc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x56 16 dc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x57 16 dc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x58 16 dc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x59 16 dc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x5a 16 dc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x5b 16 dc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
16 GLXFBConfigs:
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x3e 0 tc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x3f 0 tc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x40 0 tc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x41 0 tc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x42 0 tc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x43 0 tc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x44 0 tc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x45 0 tc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x46 0 dc 0 16 0 r . . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x47 0 dc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x48 0 dc 0 16 0 r y . 5 6 5 0 0 16 0 0 0 0 0 0 0 None
0x49 0 dc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 0 0 0 Slow
0x4a 0 dc 0 16 0 r . . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x4b 0 dc 0 16 0 r . . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
0x4c 0 dc 0 16 0 r y . 5 6 5 0 0 16 8 0 0 0 0 0 0 Slow
0x4d 0 dc 0 16 0 r y . 5 6 5 0 0 16 8 16 16 16 0 0 0 Slow
glxgears (here's where it just crashes, though X continues to function just fine...)
Note1: I get roughly the same problem using any applications that use GL
Note2: The error for the drirc isn't a fatal error, so isn't a big deal in my experience.
Note3: No seg fault reported in dmesg.
libGL: XF86DRIGetClientDriverName: 6.7.0 mach64 (screen 0)
libGL: OpenDriver: trying /usr/lib/xorg/modules/dri/tls/mach64_dri.so
libGL: OpenDriver: trying /usr/lib/xorg/modules/dri/mach64_dri.so
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 4, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 4, (OK)
drmOpenByBusid: drmOpenMinor returns 4
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
libGL error:
Can't open configuration file /etc/drirc: No such file or directory.
libGL error:
Can't open configuration file /root/.drirc: No such file or directory.
*** glibc detected *** glxgears: free(): invalid next size (fast): 0x097031d8 ***
======= Backtrace: =========
/lib/libc.so.6[0xb7f12281]
/lib/libc.so.6[0xb7f139ba]
/lib/libc.so.6(cfree+0x6d)[0xb7f16abd]
/usr/lib/libX11.so.6(_XReply+0x2c7)[0xb7dcd667]
/usr/lib/libGL.so.1(XF86DRICreateDrawable+0x9c)[0xb8052d3c]
/usr/lib/libGL.so.1[0xb80524f3]
/usr/lib/libGL.so.1[0xb802f50e]
/usr/lib/libGL.so.1(glXMakeCurrentReadSGI+0xaa)[0xb802f78a]
/usr/lib/libGL.so.1(glXMakeCurrent+0x23)[0xb802faf3]
glxgears[0x804a35e]
/lib/libc.so.6(__libc_start_main+0xe6)[0xb7ebca36]
glxgears[0x8049101]
======= Memory map: ========
08048000-0804c000 r-xp 00000000 08:02 66014 /usr/bin/glxgears
0804c000-0804d000 rwxp 00003000 08:02 66014 /usr/bin/glxgears
0949d000-09717000 rwxp 00000000 00:00 0 [heap]
b2f00000-b2f21000 rwxp 00000000 00:00 0
b2f21000-b3000000 ---p 00000000 00:00 0
b30be000-b30db000 r-xp 00000000 08:02 6925 /usr/lib/libgcc_s.so.1
b30db000-b30dc000 rwxp 0001c000 08:02 6925 /usr/lib/libgcc_s.so.1
b30e7000-b339b000 rwxp 00000000 00:00 0
b339b000-b709b000 rwxs 18204000 00:0c 5948 /dev/dri/card0
b709b000-b729b000 rwxs 18004000 00:0c 5948 /dev/dri/card0
b729b000-b7a9b000 rwxs fd000000 00:0c 5948 /dev/dri/card0
b7a9b000-b7abf000 r-xp 00000000 08:02 34101 /usr/lib/libexpat.so.1.5.2
b7abf000-b7ac1000 rwxp 00023000 08:02 34101 /usr/lib/libexpat.so.1.5.2
b7ac1000-b7c9a000 r-xp 00000000 08:02 59243 /usr/lib/xorg/modules/dri/libdricore.so
b7c9a000-b7cae000 rwxp 001d9000 08:02 59243 /usr/lib/xorg/modules/dri/libdricore.so
b7cae000-b7cb9000 rwxp 00000000 00:00 0
b7cb9000-b7d04000 r-xp 00000000 08:02 60911 /usr/lib/xorg/modules/dri/mach64_dri.so
b7d04000-b7d06000 rwxp 0004a000 08:02 60911 /usr/lib/xorg/modules/dri/mach64_dri.so
b7d06000-b7d09000 rwxp 00000000 00:00 0
b7bb0000-b7bb7000 r-xp 00000000 08:02 2676 /lib/librt-2.10.1.so
b7bb7000-b7bb8000 r-xp 00006000 08:02 2676 /lib/librt-2.10.1.so
b7bb8000-b7bb9000 rwxp 00007000 08:02 2676 /lib/librt-2.10.1.so
b7bb9000-b7bbd000 r-xp 00000000 08:02 34750 /usr/lib/libXdmcp.so.6.0.0
b7bbd000-b7bbe000 rwxp 00003000 08:02 34750 /usr/lib/libXdmcp.so.6.0.0
b7bbe000-b7bc0000 r-xp 00000000 08:02 34742 /usr/lib/libXau.so.6.0.0
b7bc0000-b7bc1000 rwxp 00001000 08:02 34742 /usr/lib/libXau.so.6.0.0
b7bc1000-b7bc3000 r-xp 00000000 08:02 2687 /lib/libdl-2.10.1.so
b7bc3000-b7bc4000 r-xp 00001000 08:02 2687 /lib/libdl-2.10.1.so
b7bc4000-b7bc5000 rwxp 00002000 08:02 2687 /lib/libdl-2.10.1.so
b7bc5000-b7bd9000 r-xp 00000000 08:02 2673 /lib/libpthread-2.10.1.so
b7bd9000-b7bda000 r-xp 00014000 08:02 2673 /lib/libpthread-2.10.1.so
b7bda000-b7bdb000 rwxp 00015000 08:02 2673 /lib/libpthread-2.10.1.so
b7bdb000-b7bde000 rwxp 00000000 00:00 0
b7bde000-b7be6000 r-xp 00000000 08:02 59196 /usr/lib/libdrm.so.2.4.0
b7be6000-b7be7000 rwxp 00008000 08:02 59196 /usr/lib/libdrm.so.2.4.0
b7be7000-b7bff000 r-xp 00000000 08:02 34843 /usr/lib/libxcb.so.1.1.0
b7bff000-b7c00000 rwxp 00017000 08:02 34843 /usr/lib/libxcb.so.1.1.0
b7c00000-b7c10000 r-xp 00000000 08:02 34851 /usr/lib/libxcb-glx.so.0.0.0
b7c10000-b7c11000 rwxp 00010000 08:02 34851 /usr/lib/libxcb-glx.so.0.0.0
b7c11000-b7c12000 r-xp 00000000 08:02 36038 /usr/lib/libX11-xcb.so.1.0.0
b7c12000-b7c13000 rwxp 00000000 08:02 36038 /usr/lib/libX11-xcb.so.1.0.0
b7c13000-b7c17000 r-xp 00000000 08:02 59215 /usr/lib/libXfixes.so.3.1.0
b7c17000-b7c18000 rwxp 00003000 08:02 59215 /usr/lib/libXfixes.so.3.1.0
b7c18000-b7c1a000 r-xp 00000000 08:02 59234 /usr/lib/libXdamage.so.1.1.0
b7c1a000-b7c1b000 rwxp 00001000 08:02 59234 /usr/lib/libXdamage.so.1.1.0
b7c1b000-b7c1c000 rwxp 00000000 00:00 0
b7c1c000-b7c20000 r-xp 00000000 08:02 58625 /usr/lib/libXxf86vm.so.1.0.0
b7c20000-b7c21000 rwxp 00003000 08:02 58625 /usr/lib/libXxf86vm.so.1.0.0
b7c21000-b7c2f000 r-xp 00000000 08:02 57974 /usr/lib/libXext.so.6.4.0
b7c2f000-b7c30000 rwxp 0000d000 08:02 57974 /usr/lib/libXext.so.6.4.0
b7c30000-b7d49000 r-xp 00000000 08:02 36044 Aborted
So there it is. I'm using the latest and greatest archlinux has to offer. I've followed every wiki, and every forum post since 2004 that relates to DRI on the Mach64 on linux. I've spent a solid 5 days on this, and can't resolve it.
I believe the problem to solve is this error:
*** glibc detected *** glxgears: free(): invalid next size (fast): 0x097031d8 ***
I also believe it's related to this reported bug:
http://bugs.archlinux.org/task/15354
Although, he was able to solve the problem by using newer drivers for his video card... I believe that the ones available in extra for the mach64 card actually are the latest.
I'm not a C guru (I'm more of a java guy), so memory management isn't my thing. I don't believe that I could hack the source to solve any memory allocation errors (even if I could find the specific source file to modify).
Perhaps I should try recompiling the mach64 drivers using the new mesa? I don't actually know enough about that to know where to start, but it's the best idea I have.
The more I look into the problem, the more it appears to be a mach64 driver problem related to memory mismanagement.
Note: I can get this to work in Debian Lenny, so it is possible.
UPDATE: I can't figure out how to compile xf86-video-mach64... I can get the latest with git, but it doesn't seem to include a Makefile... so I'm stumped.
UPDATE2: Ok, I got them to compile (had to use autogen.sh), but it didn't solve my problem... So I'm onto recompiling mesa from git... I'm currently stuck on:
makedepend: command not found
Ideas welcome.
Last edited by Daemonjax (2009-07-06 02:43:56)

HP dv3510nr suspend-to-ram / resume SATA issues

I'm trying to get suspend to ram working on my HP dv3510nr.. The problem is that when it resumes, the SATA drive seems to error out and cause the file system to fail. I've tried s2ram -f with a few of it's options, and pm-suspend. Neither resume properly (Actually, from the dmesg output it looks like it doesn't suspend properly either). Suspend takes about 30-40 seconds, but resume takes about 3-5. I have installed a Patriot 32GB SSD drive on this machine. I'm wondering if that can cause something like this. I am also using dm-crypt w/ aes-xts encryption for /dev/sda2. This maps to /dev/mapper/root, which is an ext4 partition. /dev/sda1 is an encrypted swap partition that gets setup on each boot by /etc/crypttab.cd
uname:
Linux shodan 2.6.28-ARCH #1 SMP PREEMPT Wed Feb 18 21:57:41 CET 2009 x86_64 Intel(R) Core(TM)2 Duo CPU P7350 @ 2.00GHz GenuineIntel GNU/Linux
dmesg:
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Stopping disk
NVRM: RmPowerManagement: 4
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1.00: revalidation failed (errno=-5)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1.00: revalidation failed (errno=-5)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: qc timeout (cmd 0xec)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1.00: revalidation failed (errno=-5)
ata1.00: disabled
ehci_hcd 0000:00:1d.7: PCI INT A disabled
uhci_hcd 0000:00:1d.3: PCI INT C disabled
uhci_hcd 0000:00:1d.2: PCI INT D disabled
uhci_hcd 0000:00:1d.1: PCI INT B disabled
uhci_hcd 0000:00:1d.0: PCI INT A disabled
HDA Intel 0000:00:1b.0: PCI INT A disabled
ACPI handle has no context!
ehci_hcd 0000:00:1a.7: PCI INT D disabled
uhci_hcd 0000:00:1a.1: PCI INT B disabled
uhci_hcd 0000:00:1a.0: PCI INT A disabled
ACPI: Preparing to enter system sleep state S3
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3995.51 BogoMIPS (lpj=6656821)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 3072K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU P7350 @ 2.00GHz stepping 06
Switched to high resolution mode on CPU 1
CPU1 is up
ACPI: Waking up from system sleep state S3
ACPI: EC: non-query interrupt received, switching to interrupt mode
pcieport-driver 0000:00:01.0: restoring config space at offset 0x1 (was 0x100007, writing 0x100407)
pcieport-driver 0000:00:01.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:1a.7: setting latency timer to 64
HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100006, writing 0x100002)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0xd401d301)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0xd920d820)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x7 (was 0x20000000, writing 0x4030)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x6 (was 0x0, writing 0x20200)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: restoring config space at offset 0xf (was 0x200, writing 0x20b)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x9 (was 0x10001, writing 0xd501d411)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x8 (was 0x0, writing 0xd810d710)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x7 (was 0x20000000, writing 0x2020)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x6 (was 0x0, writing 0x30300)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.5: restoring config space at offset 0xf (was 0x200, writing 0x20b)
pcieport-driver 0000:00:1c.5: restoring config space at offset 0x9 (was 0x10001, writing 0xd601d511)
pcieport-driver 0000:00:1c.5: restoring config space at offset 0x8 (was 0x0, writing 0xd700d610)
pcieport-driver 0000:00:1c.5: restoring config space at offset 0x7 (was 0x20000000, writing 0x1010)
pcieport-driver 0000:00:1c.5: restoring config space at offset 0x6 (was 0x0, writing 0x70500)
pcieport-driver 0000:00:1c.5: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
pcieport-driver 0000:00:1c.5: setting latency timer to 64
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb7: root hub lost power or was reset
uhci_hcd 0000:00:1d.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.3: setting latency timer to 64
usb usb8: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0, writing 0xfff0)
pci 0000:00:1e.0: restoring config space at offset 0x7 (was 0x22800000, writing 0x228000f0)
pci 0000:00:1e.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
pci 0000:00:1e.0: setting latency timer to 64
ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
ahci 0000:00:1f.2: setting latency timer to 64
NVRM: RmPowerManagement: 5
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: configured for UDMA/100
ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
ata2: irq_stat 0x40000001
ata2.00: configured for UDMA/100
ata2: EH complete
r8169 0000:02:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
r8169 0000:02:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfffe0000)
r8169 0000:02:00.0: restoring config space at offset 0x8 (was 0xc, writing 0xd300000c)
r8169 0000:02:00.0: restoring config space at offset 0x6 (was 0x4, writing 0xd8200004)
r8169 0000:02:00.0: restoring config space at offset 0x4 (was 0x1, writing 0x3001)
r8169 0000:02:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
r8169 0000:02:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
pci 0000:03:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
pci 0000:03:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xd7100004)
pci 0000:03:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100006)
sd 0:0:0:0: [sda] Starting disk
sd 0:0:0:0: [sda] START_STOP FAILED
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
PM: Device 0:0:0:0 failed to resume: error 262144
usb 2-4: reset high speed USB device using ehci_hcd and address 3
usb 2-6: reset high speed USB device using ehci_hcd and address 4
usb 3-1: reset full speed USB device using uhci_hcd and address 2
usb 3-2: reset full speed USB device using uhci_hcd and address 3
Restarting tasks ... done.
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 4829056
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 4829056
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 4829056
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 10495792
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 10495792
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 10495792
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6221472
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6221472
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6221472
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 6229936
sd 7:0:0:0: [sdc] 16134144 512-byte hardware sectors: (8.26 GB/7.69 GiB)
sd 7:0:0:0: [sdc] Write Protect is off
sd 7:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdc] Assuming drive cache: write through
sd 7:0:0:0: [sdc] 16134144 512-byte hardware sectors: (8.26 GB/7.69 GiB)
sd 7:0:0:0: [sdc] Write Protect is off
sd 7:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
EXT4-fs: barriers enabled
kjournald2 starting. Commit interval 5 seconds
EXT4 FS on sdc1, internal journal on sdc1:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 5134096
Buffer I/O error on device dm-0, logical block 114682
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 16041792
Buffer I/O error on device dm-0, logical block 1478144
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 16042016
Buffer I/O error on device dm-0, logical block 1478172
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 13169360
Buffer I/O error on device dm-0, logical block 1119090
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 15755192
Buffer I/O error on device dm-0, logical block 1442319
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 16033624
Buffer I/O error on device dm-0, logical block 1477123
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 16037816
Buffer I/O error on device dm-0, logical block 1477647
lost page write due to I/O error on dm-0
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 29646280
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 15747520
Buffer I/O error on device dm-0, logical block 1441360
lost page write due to I/O error on dm-0
JBD2: Detected IO errors while flushing file data on dm-0:8
Aborting journal on device dm-0:8.
sd 0:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 29644608
Buffer I/O error on device dm-0, logical block 3178496
lost page write due to I/O error on dm-0
JBD2: I/O error detected when updating journal superblock for dm-0:8.
ext4_abort called.
EXT4-fs error (device dm-0): ext4_journal_start_sb: Detected aborted journal
Remounting filesystem read-only
lspci:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93)
00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation GeForce 9300M GS (rev a1)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
03:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection
lspci -vvv:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: d0000000-d2ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Hewlett-Packard Company Device 1505
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4161
Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise-
Slot # 1, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [140] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 60e0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 60c0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at d9304c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d9300000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00004fff
Memory behind bridge: d8200000-d92fffff
Prefetchable memory behind bridge: 00000000d3000000-00000000d40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 0, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Hewlett-Packard Company Device 1505
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d7100000-d81fffff
Prefetchable memory behind bridge: 00000000d4100000-00000000d50fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 1, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Hewlett-Packard Company Device 1505
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=07, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d6100000-d70fffff
Prefetchable memory behind bridge: 00000000d5100000-00000000d60fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 5, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Hewlett-Packard Company Device 1505
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 60a0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 6080 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 6060 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 6040 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d9304800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Hewlett-Packard Company Device 1505
00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 763
Region 0: I/O ports at 6108 [size=8]
Region 1: I/O ports at 6114 [size=4]
Region 2: I/O ports at 6100 [size=8]
Region 3: I/O ports at 6110 [size=4]
Region 4: I/O ports at 6020 [size=32]
Region 5: Memory at d9304000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Mask- 64bit- Count=1/16 Enable+
Address: fee0300c Data: 4189
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 11
Region 0: Memory at d9305000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 6000 [size=32]
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: nVidia Corporation GeForce 9300M GS (rev a1) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d0000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at 5000 [size=128]
Expansion ROM at <ignored> [disabled]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information <?>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
Subsystem: Hewlett-Packard Company Device 1505
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 762
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at d8200000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at d3000000 (64-bit, prefetchable) [size=64K]
Expansion ROM at d3020000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Mask- 64bit+ Count=1/1 Enable+
Address: 00000000fee0300c Data: 4199
Capabilities: [70] Express (v1) Endpoint, MSI 01
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-49
Kernel driver in use: r8169
Kernel modules: r8169
03:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection
Subsystem: Intel Corporation Device 1211
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d7100000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140] Device Serial Number 26-ff-ab-ff-ff-5d-21-00
Kernel modules: iwlagn
lsmod:
Module Size Used by
ext2 73872 1
snd_seq_oss 35584 0
snd_seq_midi_event 9344 1 snd_seq_oss
snd_seq 58336 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 9364 2 snd_seq_oss,snd_seq
usb_storage 110272 1
snd_pcm_oss 45440 0
snd_mixer_oss 18944 1 snd_pcm_oss
serio_raw 8196 0
sg 31840 0
lis3lv02d 13288 0
uhci_hcd 27552 0
snd_pcsp 13052 0
iTCO_wdt 15184 0
iTCO_vendor_support 5636 1 iTCO_wdt
psmouse 57116 0
r8169 39428 0
mii 7296 1 r8169
video 22420 0
output 5248 1 video
leds_hp_disk 5256 0
led_class 6280 1 leds_hp_disk
wmi 8896 0
snd_hda_intel 531252 0
snd_pcm 82952 3 snd_pcm_oss,snd_pcsp,snd_hda_intel
snd_timer 24720 2 snd_seq,snd_pcm
snd_page_alloc 11792 2 snd_hda_intel,snd_pcm
snd_hwdep 10632 1 snd_hda_intel
snd 65096 10 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcsp,snd_hda_intel,snd_pcm,snd_timer,snd_hwdep
soundcore 9632 1 snd
nvidia 8112272 0
i2c_core 26144 1 nvidia
ehci_hcd 41356 0
usbcore 160432 4 usb_storage,uhci_hcd,ehci_hcd
intel_agp 33136 0
thermal 20896 0
processor 46648 3 thermal
evdev 13984 6
fan 7304 0
button 9504 0
battery 14600 0
ac 7176 0
rtc_cmos 14040 0
rtc_core 21060 1 rtc_cmos
rtc_lib 4992 1 rtc_core
ext4 231608 1
mbcache 10244 2 ext2,ext4
jbd2 65456 1 ext4
crc16 4096 1 ext4
aes_x86_64 10240 4
aes_generic 29352 1 aes_x86_64
xts 5632 2
gf128mul 9728 1 xts
dm_crypt 16392 1
dm_mod 62704 5 dm_crypt
sd_mod 29096 5
sr_mod 18884 0
cdrom 39080 1 sr_mod
ahci 36876 2
libata 176224 1 ahci
scsi_mod 119256 5 usb_storage,sg,sd_mod,sr_mod,libata
Anyone have any ideas on how to fix this? Thanks.
Last edited by soleblaze (2009-02-26 19:12:29)

as my dv3550eg has no problem with suspend and resume, i think this is a problem with device-mapper and or cryptsetup or the ssd-drive.

SATA in G4 (agp)

Similar Messages

Maybe you are looking for