SATA RAID Controller under Solaris 10

I want to set up my Sun Ultra AXMP on a SATA RAID5, but i did not find yet a controller wich is supported by Solaris 10.
I already looked for support on the Adaptec 2410SA and all other Adaptec Controlleres (searched here: http://www.sun.com/bigadmin/hcl/search.jsp), but did only find one wich is only supporting 2 drives...
Are there any Controllers wich are supported by Solaris 10 OS and are RAID5 ready?
If they are only supported by other Solaris versions, its also ok.

Hi,
Thank you for the information. As you said from the behavior it seems that the build-in drivers of Windows Server Technical Preview will not work with the specific motherboard hence the RAID1 cannot work well. 
I'll log the issue down. 
If you have any feedback on our support, please send to [email protected]

Similar Messages

  • Oracle Ent. Linux  drivers for HP Smart Array B110i Sata Raid Controller

    Trying to install Oracle Ent. Linux (OEL) release 4 update 8 on HP DL 180 G6 server. Where we can find OEL drivers for the sata raid controller ?
    (HP Smart Array B110i Sata Raid Controller)
    Thanks in advance.

    The HP support side shows a Linux certification matrix at: http://h18000.www1.hp.com/products/servers/linux/hplinuxcert.html
    From there you can also download the necessary drivers and instructions or use HP smartstart CD which prepares the system for the OS you need to install. Oracle Enterprise Linux is binary compatible with RHEL. You will need to click on "Archive" to see support for Enterprise Linux version 4 and older.
    Also interesting should be Red Hat Enterprise Linux Technical Exceptions at
    http://h18000.www1.hp.com/products/servers/linux/supportmatrix/rhel/exceptions/rhel-exceptions.html

  • Intel(R) ESB2 SATA RAID Controller not working out of the box

    Dear all,
    I'm using, for my tests, an old server with a supermicro X7DBN Server motherboard.
    This motherboard comes with an embedded Intel(R) ESB2 SATA RAID Controller.
    When I try a native installation from the technical preview DVD it sees the RAID1 volume that has been created (2 disk mirror) but when I select it to proceed with the installation there is an unknown error stating that it's impossible to write to this disk.
    The same installation works perfectly with 2012R2 and the out of the box driver provided bin the install media.
    An update from the previously installed 2012R2 to the Windows Server Technical Preview also works without problem.
    It would make sens for MS to revert to the driver version embedded in 2012R2 for Intel(R) ESB2 SATA RAID Controller which is:
    Name : Intel(R) ESB2 SATA RAID Controller
    Date : 10.08.2010
    Version : 8.6.2.1025
    inf section : iaStor_Inst_RAID
    Device ID : PCI\VEN_8086&DEV_2682&CC_0104

    Hi,
    Thank you for the information. As you said from the behavior it seems that the build-in drivers of Windows Server Technical Preview will not work with the specific motherboard hence the RAID1 cannot work well. 
    I'll log the issue down. 
    If you have any feedback on our support, please send to [email protected]

  • Need software for Intel ESB2 SATA RAID Controller for Windows 2012rR

    I have installed Windows 2012r2 on my HP XW8600 and I found the software for the LSI Adapter (SAS 3000 series) but I am unable to find the software for management of the Intel ESB2 SATA RAID controller.  The only software I could find was listed as a Windows 7 application but will not install onto my Windows 2012r2.   Thank You 

    That looks exactly like the software I tried and an error reported this software will not install on this platform.  I will try again tonite and see what happens.  I will test all the apps on that list starting with the latest and see what happens. I thank you for your help.   

  • KT4 Ultra (6590) need update of the Promise SATA RAID Controller PDC20376

    The last Bios update AMI 1.4 for the KT4 Ultra (6590) have built in the bios version 1.00.0.18 for the PDC20376 (Promise 376).
    I can configure 2 maxtor (6E040T0) sata1 in a raid0 array and it works under WinXP SP3,
    but the 2 drives are working in UDMA5 according to the FastBuild Utility when the motherboard specifications talks about 150Mb (SATA1).
    It's not an OS problem because the FastBuild Utility at Bios startup show the UDMA5 mode for HDD.
    It's not a Maxtor 6E040T0 (SATA1) problem because have no jumper to set.
    The Promise support center don't provide support for built in raid controller but the responce was that it's related to a known bios issue of the controller, so i have to update.
    For the last Bios version for the S150 TX4 controller look at:
    http://promise.com/support/download/download2_eng.asp?productId=108&category=all&os=100&go=GO
    It's impossible to update the bios with the promise tool because the controller is integrated in the motherboard.
    I read for example than on the motherboard K7N2 Delta-ILSR the bios version of the Promise 376 controller is 1.00.0.21:
    https://forum-en.msi.com/index.php?topic=92756.msg665966#msg665966
    I think the only solution is a modding bios, where i have to replace only the Promise controller bios but:
    1) The tool amibcp.exe can't open the A6590VMS.140 AMI bios (renamed .rom), i don't know why!!!
    2) What promise controller bios rom file is good?
    Can anyone out there help . . . please ?

    This is my results compared to my other UDMA6 HDD on IDE1, HDTach long bench stop with "Read Error" and only quick bench works.
    The version of the Controller driver under WinXP-SP3 is 1.0.1.29 and I configured the driver in the PAM Utility with:
    "Driver Write Cache" enabled and "Write Back" as cache settings (The 2 Maxtor SATA1 in RAID have 2MB of cache, but i don't know How many cache have the controller!!).
    The Burst Speed is too strange!!! quick bench error?
    I made it so your image is clickable.
    -Frankenputer

  • 3ware SATA RAID-controller drivers?

    Anyone knows is 3ware SATA RAID-controllers supported in Solaris 10 x86?

    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=398
    K7N2G-ILSR
    is board with promise raid and vga

  • Promise PDC20579 SATA/RAID controller

    I'm trying to get the piece of shit working with Linux, but haven't had any luck. I'm not sure which Promise add-on cards use this chip as this one is built into my mobo, where it provides 2-SATA and 1-PATA port. I'm using the PATA with 2 drives (160GB, 60GB) and I don't want to setup a RAID array, but just use it as an extra IDE controller.
    The BIOS detects the drives correctly but linux doesn't recognize the Promise controller, so it's not assigning device nodes for the drives (no hd* or sd*) and I can't seem to make it work. The correct kernel module, according to the net, is sata_promise, but I'm not certain it supports the PATA part of the controller. When loaded, it prints info about the connected drives to dmesg, but never assigns device nodes.

    Okay, so I found a patch in the Red Hat kernel mailing list that seems to work. It patches the sata-promise module to attempt to detect PATA ports when nothing is connected via SATA. I don't have any SATA discs so I cannot check to see if it breaks anything in regards to SATA.
    If anyone else is interested, I'll strip the RH specific stuff from the patch and submit it to the Arch kernel devs for review. Not sure if enough people would find is useful tho.

  • Promise 20376 SATA Raid Controller Drivers?

       Hi I'm trying to install WinXP with an K7N2GM2 - ILSR board and I'm having problems with the SATA drivers I've downloaded (from http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_list.php?part=1&kind=4&CHIP=4&COM=19). The 'make disk' instructions included is a bit awkward but I tried putting the different files on a floppy several different ways, but to no avail. When windows asks for a floppy to install the sata drivers, it reads the disk for a while and returns back to the 'insert a disk and hit ENTER.' I went to Promise's website and download some drivers from there but again to no avail, the drivers included on the CD with the mb have not worked either.
       Just to make sure I'm simply not putting the correct files on floppy or not putting them in the proper directory structure, I'll give you an example of what I have put on the floppy:
    WinXP <-Folder containing drivers
    txtsetup.oem
    ULSATA
    fasttx2k
    and the text files like 'makedisk'
       I've also taken all of the files out of the WinXP directory and had all files in the same location A:\ . I'm not sure what to do at this point, I'm adept with computers and I know that sata can be finiky, but this one going nowhere fast. Could somebody help? BTW I'm only using one HD, a WD 80GB Sata HD which I had to put in an array ('functioning').

    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=398
    K7N2G-ILSR
    is board with promise raid and vga

  • A85 SATA Raid Controller

    hi guys, didnt find any new posting about this, I just found out one of my mirror drive is damage and my controller is running in degraded mode. question is how to replace faulty HDD without losing data, this is no software that comes with the machine that allows me to do that like the servers do. When i go to BIOS, everything says it will destroy all data and I wasnt sure it means destroy ALL or just the broken raid drive?
    Anyone tried?

    losmeme wrote:
    Yes, it will destroy the data. Most HDD manufacturers have programs that will mirror drives for you. If you have a Western Digital HDD, download the Acronis True Image software from HERE.
    Ah, what is then the point of having RAID??? Actually solution exists, check Link for example.
    P.S. Always have backup copy of your data. RAID is not backup. Many things can go wrong, not just HDDs.
    Disclaimer: While I do work for Lenovo Partner, all my contributions are my personal, non-official and not that of Lenovo or my employer.

  • Promise T3 SATA RAID controller Vista x64 driver OK for W7 x64?

    Before I walk down the path of tears again, or at least roll the dice, has anyone used the Vista 64bit drivers for the Promise T3 controller that comes with the K9A2 Platinum on W7 64 bit?  And if so, did they work?
    From here:  http://www.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=1332
    Thanks,
    Anthony
    Specs:
    Operating System
       MS Windows 7 Ultimate 64-bit
    CPU
       AMD Phenom X4 9550    28 °C
       Agena 65nm Technology
    RAM
       8.0GB Dual-Channel DDR2 @ 333MHz  5-5-5-13
    Motherboard
       MICRO-STAR INTERNATIONAL CO.,LTD MS-7376 (CPU 1)
    Graphics
       Generic PnP Monitor on ATI Radeon HD 3870
       ATI Radeon HD 3870 (VISIONTEK)   47 °C
       ATI Radeon HD 3870 (VISIONTEK)   47 °C
    Hard Drives
        1000GB MICRONET FANTOM DRIVE IEEE 1394 SBP2 Device (1394)
        749GB ATI 1X2 Mirror/RAID1 SCSI Disk Device (SCSI)
    Optical Drives
       ATAPI DVD A  DH20A4P ATA Device
    Audio
       High Definition Audio Device

     executivetechnology, if you have a problem please start you're own new topic instead or resurrecting an old one from 1 1/2 years ago.
          >> Please read and comply with the Forum Rules <<
          >> Posting Guide <<

  • SATA RAID conflics with POMISE T3 RAID Bios

    I've read quite a few of the RAID setup issues concerning the "Extra" RAID settings under "integrated peripherals" for the K9A2 Platinum. My problem seems to be a bit unique. I can't get both the SATA RAID and the Promise "Fast Track" to work together. If I enable the Extra RAID Controllers the Fastrack Bios does not recognize my SATA RAID.
    This simply means that for some reason the motherboard SATA RAID conflicts or disables the PROMISE RAID Bios and vice versa. So I have not been able to activate my eSATA ports or use anything connected to the SATA5-6 ports without going into the CMOS and setting SATA DEVICES to IDE and then turning on the EXTRA Raid Controller under "Integrated Peripherals" in the CMOS. Unless I'm wrong. I am almost sure that this scenario is right.
    The second issue is that I cannot get my ram to go in DUAL CHANNEL  mode. But I will post that issue another time.
    thx
    Please Advise.
    Ami Bios v1.4
    K9A2 Platinum MB, 790FX,
    AMD 9850 Black Edition,
    8GB GSkill RAM (800Mhz),
    Samsung 500GB SATA11 (x4),
    Radeon HD 3870 512 MB Video,
    Rosewill 950Watt PSU,
    Pioneer DVD RW,
    NEC DVD RW,
    9-in-1 USB Card Reader
    2 ext (USB/eSATA) hard Drives (eSATA will not work because these ports are controlled by the PROMISE T3 Bios)

    With Vista Ultimate SP1 on my machine the USB Flasher Tool kept on crashing when the BIOS was at v 1.2 on the KA92 mainboard.
    The DOS window came up fine but it appeared that every susequent module that was brought up for detecting the motherboard caught some kind of conlfict and terminated causing Vista to summon the program terminated message box. Eventually the dos prompt would state that it could not detect the motherboard and close. All in red text. This happened only when I flashed the BIOS with v1.2. I wanted to go back to 1.3 just to verify that the BIOS version was the cause and the only reason I got back to 1.3 or 1.4 easily was becaus it was backed up by the tool so all I had to do was rename the backup.bin file(s). Again everything went as expected with the USB Flasher Tool until I loaded the v1.2 BIOS. It could not even detect the mainboard.
    The only reason I didn't need the tool anymore was that it backed up the versions of the bios for each time that I had flashed the bios previously.
    Ami Bios v1.2
    K9A2 Platinum MB, 790FX,
    AMD 9850 Black Edition,
    8GB GSkill RAM (800Mhz),
    Samsung 500GB SATA2 (x4),
    Radeon HD 3870 512 MB Video,
    Rosewill 950Watt PSU,
    Pioneer DVD RW,
    NEC DVD RW,
    9-in-1 USB Card Reader

  • Sil3114 RAID controller

    I recently installed a sata raid controller in my new solaris 10 box. It is based on the sil-3114 chipset. Unfortunatly Solaris does not recognize either of the sata drives that are connected to it. When I do prtconf -pv the device shows up (I think) with the following information:
    Node 0x000012
    assigned-addresses: 81024810.00000000.00009000.00000000.00000008.81024814.00000000.00009400.00000000.00000004.81024818.00000000.00009800.00000000.00000008.8102481c.00000000.00009c00.00000000.00000004.81024820.00000000.0000a000.00000000.00000010.82024824.00000000.fa009000.00000000.00000400.82024830.00000000.00000000.00000000.00080000
    reg: 00024800.00000000.00000000.00000000.00000000.01024810.00000000.00000000.00000000.00000008.01024814.00000000.00000000.00000000.00000004.01024818.00000000.00000000.00000000.00000008.0102481c.00000000.00000000.00000000.00000004.01024820.00000000.00000000.00000000.00000010.02024824.00000000.00000000.00000000.00000400.02024830.00000000.00000000.00000000.00080000
    compatible: 'pci1095,3114.1095.6114.2' + 'pci1095,3114.1095.6114' + 'pci1095,6114' + 'pci1095,3114.2' + 'pci1095,3114' + 'pciclass,010400' + 'pciclass,0104'
    model: 'RAID controller'
    power-consumption: 00000001.00000001
    66mhz-capable:
    fast-back-to-back:
    devsel-speed: 00000001
    interrupts: 00000001
    max-latency: 00000000
    min-grant: 00000000
    subsystem-vendor-id: 00001095
    subsystem-id: 00006114
    unit-address: '9'
    class-code: 00010400
    revision-id: 00000002
    vendor-id: 00001095
    device-id: 00003114
    name: 'pci1095,6114'
    I am unable to find additional information on what I have to do to use this controller. What am I missing here?
    Thank you for your help.

    ok, I gave devfsadm a shot. Nothing spectacular happened.
    I also peaked in /var/adm/messages and got the following:
    May 12 13:30:10 pbfs01 genunix: [ID 935449 kern.info]      ATA DMA off: disabled. Control with "atapi-cd-dma-enabled" property
    May 12 13:30:10 pbfs01 genunix: [ID 882269 kern.info]      PIO mode 4 selected
    May 12 13:30:10 pbfs01 genunix: [ID 935449 kern.info]      ATA DMA off: disabled. Control with "atapi-cd-dma-enabled" property
    May 12 13:30:10 pbfs01 genunix: [ID 882269 kern.info]      PIO mode 4 selected
    May 12 13:30:10 pbfs01 genunix: [ID 935449 kern.info]      ATA DMA off: disabled. Control with "atapi-cd-dma-enabled" property
    May 12 13:30:10 pbfs01 genunix: [ID 882269 kern.info]      PIO mode 4 selected
    May 12 13:30:10 pbfs01 genunix: [ID 773945 kern.info]      UltraDMA mode 5 selected
    I then tried enabling ATA DMA mode using eeprom atapi-cd-dma-enabled=1 and on reboot the message changed to the following:
    May 12 14:30:01 pbfs01 genunix: [ID 773945 kern.info]      UltraDMA mode 2 selected
    May 12 14:30:01 pbfs01 last message repeated 2 times
    May 12 14:30:01 pbfs01 genunix: [ID 773945 kern.info]      UltraDMA mode 5 selected
    The full /var/adm/messages file is as follows:
    May 12 14:46:01 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: rsm0
    May 12 14:46:01 pbfs01 genunix: [ID 936769 kern.info] rsm0 is /pseudo/rsm@0
    May 12 14:46:01 pbfs01 pcplusmp: [ID 637496 kern.info] pcplusmp: lp (ecpp) instance 0 vector 0x7 ioapic 0x2 intin 0x7 is bound to cpu 0
    May 12 14:46:01 pbfs01 isa: [ID 202937 kern.info] ISA-device: ecpp0
    May 12 14:46:01 pbfs01 genunix: [ID 936769 kern.info] ecpp0 is /isa/lp@1,378
    May 12 14:46:01 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: devinfo0
    May 12 14:46:01 pbfs01 genunix: [ID 936769 kern.info] devinfo0 is /pseudo/devinfo@0
    May 12 14:46:01 pbfs01 pci: [ID 370704 kern.info] PCI-device: pci10de,e2@b, pci_pci0
    May 12 14:46:01 pbfs01 genunix: [ID 936769 kern.info] pci_pci0 is /pci@0,0/pci10de,e2@b
    May 12 14:46:01 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: pseudo1
    May 12 14:46:01 pbfs01 genunix: [ID 936769 kern.info] pseudo1 is /pseudo/zconsnex@1
    May 12 14:46:03 pbfs01 genunix: [ID 773945 kern.info]      UltraDMA mode 2 selected
    May 12 14:46:03 pbfs01 last message repeated 2 times
    May 12 14:46:03 pbfs01 genunix: [ID 773945 kern.info]      UltraDMA mode 5 selected
    May 12 14:46:03 pbfs01 pcplusmp: [ID 637496 kern.info] pcplusmp: asy (asy) instance 0 vector 0x4 ioapic 0x2 intin 0x4 is bound to cpu 0
    May 12 14:46:03 pbfs01 isa: [ID 202937 kern.info] ISA-device: asy0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] asy0 is /isa/asy@1,3f8
    May 12 14:46:03 pbfs01 pcplusmp: [ID 398438 kern.info] pcplusmp: asy (asy) instance #1 vector 0x3 ioapic 0x2 intin 0x3 is bound to cpu 0
    May 12 14:46:03 pbfs01 isa: [ID 202937 kern.info] ISA-device: asy1
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] asy1 is /isa/asy@1,2f8
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: ramdisk1024
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] ramdisk1024 is /pseudo/ramdisk@1024
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: lockstat0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] lockstat0 is /pseudo/lockstat@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: llc10
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] llc10 is /pseudo/llc1@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: fcp0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] fcp0 is /pseudo/fcp@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: fcsm0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] fcsm0 is /pseudo/fcsm@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: lofi0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] lofi0 is /pseudo/lofi@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: profile0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] profile0 is /pseudo/profile@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: systrace0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] systrace0 is /pseudo/systrace@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: fbt0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] fbt0 is /pseudo/fbt@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: sdt0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] sdt0 is /pseudo/sdt@0
    May 12 14:46:03 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: fasttrap0
    May 12 14:46:03 pbfs01 genunix: [ID 936769 kern.info] fasttrap0 is /pseudo/fasttrap@0
    May 12 14:46:04 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: fssnap0
    May 12 14:46:04 pbfs01 genunix: [ID 936769 kern.info] fssnap0 is /pseudo/fssnap@0
    May 12 14:46:04 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: winlock0
    May 12 14:46:04 pbfs01 genunix: [ID 936769 kern.info] winlock0 is /pseudo/winlock@0
    May 12 14:46:04 pbfs01 pseudo: [ID 129642 kern.info] pseudo-device: pm0
    May 12 14:46:04 pbfs01 genunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0
    May 12 14:46:04 pbfs01 ipf: [ID 774698 kern.info] IP Filter: v4.0.2, running.
    (sorry for the long post)
    Still no drives in smc or after issuing a format command.

  • Help Installing RAID Controller Driver

    Solaris Express 11 live CD cannot find drives('format' output says "no drives found")
    After booting up from Solaris Express 11 live CD,there is a message "Some device drivers cannot be found".
    After clicking Device Driver Utility there are two storage related items in the list with 'missing drivers':
    PromiseTechnology PDC20575 SATAII150 TX2plus
    Intel Corporation 631xESB/632xESB SATA RAID Controller
    There is an option to install 'PromiseTechnology' driver,I clicking 'install',after a while it says "Installed successfully" but 'format' still cannot find anything.
    The details for both items are below. How do I continue installation from this point ????
    Many Thanks.
    Driver URL:
    node name: pci8086,3473
    Vendor: Intel Corporation
    Device: 631xESB/632xESB SATA RAID Controller
    Sub-Vendor: Intel Corporation
    binding name: pci8086,3473
    devfs path: /pci@0,0/pci8086,3473
    pci path: 0,1f,2
    compatible name:
    (pci8086,2682.8086.3473.9)(pci8086,2682.8086.3473)(pci8086,3473)(pci8086,2682.9)(pci8086,2682)(pciclass,010400)(pciclass,0104)
    driver name: unknown
    acpi-namespace: SB.PCI0.IDE1
    assigned-addresses: 8100fa10
    reg: fa00
    compatible: pci8086,2682.8086.3473.9
    model: RAID controller
    power-consumption: 1
    66mhz-capable: TRUE
    fast-back-to-back: TRUE
    devsel-speed: 1
    interrupts: 2
    max-latency: 0
    min-grant: 0
    subsystem-vendor-id: 8086
    subsystem-id: 3473
    unit-address: 1f,2
    class-code: 10400
    revision-id: 9
    vendor-id: 8086
    device-id: 2682
    Driver URL:solaris
    node name: pci105a,3d75
    Vendor: Promise Technology, Inc.
    Device: PDC20575 (SATAII150 TX2plus)
    Sub-Vendor: Promise Technology, Inc.
    binding name: pci105a,3d75
    devfs path:
    /pci@0,0/pci8086,25f7@2/pci8086,350c@0,3/pci105a,3d75
    pci path: 5,1,0
    compatible name:
    (pci105a,3d75.105a.3d75.2)(pci105a,3d75.105a.3d75)(pci105a,3d75)(pci105a,3d75.2)(pci105a,3d75)(pciclass,018000)(pciclass,0180)
    driver name: unknown
    assigned-addresses: 81050810
    reg: 50800
    compatible: pci105a,3d75.105a.3d75.2
    model: Mass storage controller
    power-consumption: 1
    66mhz-capable: TRUE
    devsel-speed: 1
    interrupts: 1
    max-latency: 12
    min-grant: 4
    subsystem-vendor-id: 105a
    subsystem-id: 3d75
    unit-address: 1
    class-code: 18000
    revision-id: 2
    vendor-id: 105a
    device-id: 3d75

    Hi:
    See if this driver works...
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-123851-1&cc=us&dlc=en&lc=en...

  • RAID controller on G4; problems... is RAID dead? Help please!

    Hey.
    Here's the deal... Our graphics department has a MAC G4 (fully upgraded. newest patches, OS, etc.) that's got a 4 port SATA RAID controller. They use this with four 750GB hard drives as an external RAID (the OS is on a seperate, 65GB hard drive). The way it's set up, through Apple's OS, is we have the four 750GBs in pairs... those pairs are striped, and then the two sets of striped 750s are mirrored. This has worked just fine for a number of months, but we recently had a power surge, and now we're unable to mount "Monkey" (the name of the 1.4TB array).
    See the below screenshots for more clarification.
    http://www.amcdoors.com/lorenzo/raidsetup.JPG
    This shows the RAID card, and the four SATA cables coming out of it.
    http://www.amcdoors.com/lorenzo/leftside1.JPG
    As you can see in this and the below screenshots, this shows the 1.4TB Striped set as 'online', but the two below (the two 750GB hard drives) show up as "offline".
    http://www.amcdoors.com/lorenzo/leftside2.JPG
    this shows the actual drive i click on. same thing
    http://www.amcdoors.com/lorenzo/leftside3a.JPG
    If i click the entire array, you can see how it's set up (the Mirrored RAID set consisting of the two Striped RAID sets). The RAID sets (all 3 of them) are showing up as online, yet the drives are offline. No idea why. The drives are all powered, and are spinning, and plugged in.
    http://www.amcdoors.com/lorenzo/leftside3b.JPG
    when you click "Monkey Drive", nothing shows up in it. i don't remember if anything ever used to. if you click 'mount', nothing happens.
    http://www.amcdoors.com/lorenzo/leftside4.JPG
    http://www.amcdoors.com/lorenzo/leftside5.JPG
    this shows the exact same problem as the first RAID set.
    http://www.amcdoors.com/lorenzo/verifyRAIDset1.JPG
    If you try to Verify the RAID set, it shows that no repairs are necessary
    http://www.amcdoors.com/lorenzo/verifymonkey.JPG
    If you try to verify Monkey, you get a "Volume Needs Repair" error... but when you try to repair it, you get this:
    http://www.amcdoors.com/lorenzo/repairmonkey.JPG
    Really need help; this is a pretty critical problem. Someone that's familar with RAID solutions on MACs please help me out. We can't risk losing any data if at all possible.
    Thanks
    ~Lorenzo

    have you gotten this to work yet ?? if not let me know
    -d

  • LSI1030 scsi adapter does not work under solaris 10 on t5240 sparc server

    hi all,
    i have following LSI1030 scsi pci-x card in t5240 server with solaris 10u8 ..
    ## prtpicl -v ## director's cut
                             LSILogic,scsi (scsi-2, ad0000061e)
                              :DeviceID      0x8
                              :UnitAddress   8
                              :vendor-id     0x1000
                              :device-id     0x30
                              :revision-id   0xc1
                              :subsystem-vendor-id   0x103c
                              :subsystem-id  0x322a
                              :class-code    0x10000
                              :cache-line-size       0x10
                              :interrupts    00  00  00  01
                              :min-grant     0x10
                              :max-latency   0x6
                              :latency-timer         0x40
                              :devsel-speed  0x1
                              :66mhz-capable
                              :fcode-rom-offset      0xa800
                              :device_type   scsi-2
                              :wide  0x10
                              :version       1.00.38
                              :reg
    00  07  40  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00
    01  07  40  10  00  00  00  00  00  00  00  00  00  00  00  00  00  00  01  00
    03  07  40  14  00  00  00  00  00  00  00  00  00  00  00  00  00  02  00  00
    03  07  40  1c  00  00  00  00  00  00  00  00  00  00  00  00  00  02  00  00
    02  07  40  30  00  00  00  00  00  00  00  00  00  00  00  00  00  10  00  00
                              :model         LSI,1030
                              :compatible    pci103c,30
                              :assigned-addresses
    81  07  40  10  00  00  00  00  00  00  10  00  00  00  00  00  00  00  01  00
    82  07  40  14  00  00  00  00  05  20  00  00  00  00  00  00  00  02  00  00
    82  07  40  1c  00  00  00  00  05  22  00  00  00  00  00  00  00  02  00  00
    82  07  40  30  00  00  00  00  05  30  00  00  00  00  00  00  00  10  00  00
                              :mpt-version   1.02
                              :firmware-version      1.03.39.00
                              :devfs-path    /pci@500/pci@0/pci@c/pci@0/LSILogic,scsi
                              :binding-name  LSILogic,scsi
                              :instance      -1
                              :_class        scsi-2
                              :name  LSILogic,scsi
    ## prtdiag -v # director's cut
    MB                lsilOGICLSILogic,scsi                     LSI,1030
                            /pci@500/pci@0/pci@c/pci@0/LSILogic,scsi
    ## prtconf -v # director's cut
                        LSILogic,scsi (driver not attached)
                            tape (driver not attached)
                            disk (driver not attached)
    {0} ok probe-scsi-all
    /pci@500/pci@0/pci@c/pci@0/LSILogic,scsi@8
    MPT Version 1.02, Firmware Version 1.03.39.00
    Initiator ID is 7
    Target 3
      Unit 0   Removable Tape     HP      Ultrium 2-SCSI  S63Di am unable to run this controller under solaris 10, is it even possible ??
    regards, daniel
    ps. i did reconfigure reboot and tried to tweak a mpt driver by hand, i also checked a patches for mpt driver ..

    # prtconf -v | grep LSI
                        LSILogic,scsi, instance #0
                                    dev_path=/pci@500/pci@0/pci@c/pci@0/LSILogic,scsi@8:devctl
                                    dev_path=/pci@500/pci@0/pci@c/pci@0/LSILogic,scsi@8:scsi
    # cfgadm -lv c2
    Ap_Id                          Receptacle   Occupant     Condition  Information
    When         Type         Busy     Phys_Id
    c2                             connected    unconfigured unknown
    unavailable  scsi-bus     n        /devices/pci@500/pci@0/pci@c/pci@0/LSILogic,scsi@8:scsi
    # iostat -En ## cut
    rmt/0            Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
    Vendor: HP       Product: Ultrium 2-SCSI   Revision: S63D Serial No:thanks, resolved .. i added this device (mpt "pci103c,30") in /etc/driver_aliases
    regards

Maybe you are looking for

  • HP LaserJet Pro 200 color MFP M276nw - Printing problems with HPeprint App on Ipad mini

    Hi, my name is Domenico and I have the following problem: I have setup my HP LaserJet Pro 200 color MFP M276nw in HPePrint App on my Ipad mini, but I am able to print directly. When I send a page to print through my tablet, on the printer screen I ca

  • How can I transfer pictures from my iPhone 5s to iphone 6

    I Cannot get my pictures to transfer to my new iPhone 6 when I from my old iPhone 5S. It usually always transfers everything when you sign in with your apple ID

  • When in phone mode  black screen and no option to "end call" power dwn req

    ok so heres my problem after i updated to 4.0.2 now when i use the "phone" to make recieve call screen goes blank and i loose the option to "end call" then to get outta call i have to press power button and home button to reset i hav already went to

  • Errors with flashplayer 9

    My computer said I needed to install flashplayer 9 so i did that and automatically i couldn't see any kind of pictures or videos. I figured a problem must have occured so i tried uninstalling it and it wouldn't uninstall. I had to come to this websit

  • JDBC (SQL) not working in thread

    I was surprised by a strange (bug?) I had two programs that were implementing the Java Serial Port API, each interfaced to a specific instrument. I was asked to combine the two programs into one, run it on one workstation, and run it as a service. Th