Satelite A500-ST5606 Digital Signiture Errors after restoring from the Recovery Disks.

I had to replace my hard drive, I reinstalled Windows 7 Home Premium (64bit) from my recovery disks. I get a digital signiture error the following drivers:
Display Adapters
IDE ATA/ATAPI controllers
Network Adapters
Sound drivers.
Also unable to update windows using windows update, I get service is not running with it.
Please advice.
Thanks

Satellite A500-ST5606
A known problem. See my message about that.
After Restoring to New Hard Disk, No Windows Update
You may need to repeat the restore and then immediately install the new storage driver.
-Jerry

Similar Messages

DPM encountered an error while reading from the recovery point used for recovery.

Hi Guys I'm getting this error:
DPM encountered an error while reading from the recovery point used for recovery. Either the recovery point no longer exists or, if you
selected a share for recovery, the path to its contents is missing from the recovery point. (265)
The DPM Server is on Windows 2012 DPM is 2012R2 4.2.1273.0
The Server being backed up is 2012 R2 with DPM Agent 4.2.1273.0
The Server has 3 Data Volumes (C: Drive) and D and E its the D and E drive that i get this error if i try and recover data from DPM. the C Drive is fine. the D and E Drive are different
in that 1 De-dupe is enabled and 2 the Shadow Copies for these Volumes are stored on separate Disks F and G respectively.
I've removed the Protection from drives D and E and reinstated it but every recovery point created
brings up the same error message. I'm not sure where to go next do I need to Protect the Disks that have the Shadow copies on also? Many thanks in advance Gordon.

Hi,
It seems you are in a configuration where the Windows 2012 based DPM server does not understand how to read Windows 2012 R2 Dedup data structure which is what the DPM replica volume is.
See the DPM supported and unsupported scenarios
here under the deduplication issues section.
We have a fix in DPM2012 R2 UR5 that will protect the Windows 2012 R2 dedup volume in a non-dedup state on the DPM Server, but unfortunately that will not allow previous recovery points to be read.
KB3021791-Description of Update Rollup 5 for System Center 2012 R2 Data Protection Manager
Backup job for dedupe-enabled volume on Windows 2012 R2 fails. For example, Data Protection Manager backup might fail for following setup:
Data Protection Manager2012 R2 is installed on Windows Server 2012.
Data Protection Manager is protecting a dedupe-enabled volume on Windows Server 2012 R2.
This also applied to restores as the above was for D2D2T backup that may fail as it needs to read the recovery point to back it up to tape.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
posting is provided "AS IS" with no warranties, and confers no rights.

How to recover my 2000-299wm notebook too factory restore with the recovery disk

how to recover my 2000-299wm notebook qe28ua#aba too factory restore with the recovery disk Windows 7 64-bit

Hi:
Please read this document at the link below. Scroll down the page for how to recover from recovery disks.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c01867418
Paul

Windows 8.1 got corrupted and had to restore from HP recovery disk

My computer running 8.1 started cycling between IE 11 and the Windows 8.1 home screen. It would not stop so I had to initiate a recovery from my built in HP recovery drive. When I did this it wiped out my OFFICE 2010 installation. How do
I re-install? Doesn't Microsoft have the information that OFFICE 2010 was registered to my ACCOUNT? I am on travel and don't have access to the CD or the Access key.
Someone please help!

Hi,
If you cannot acess to the CD, you can get an Office 2010 installation package from below site, however, you have to enter your 25-character Product Key to download Office program:
http://office.microsoft.com/en-us/buy/netbook-FX101850729.aspx?CTT=5&origin=HA101828496
The issue is how to get your product key.
If you have ever purchased, downloaded, and installed Office 2010 online, the key was associated with a Microsoft account. You may be able to recover the Office product key in the confirmation email you received when you purchased the product online.
Or you can just contact Microsoft support (https://support.microsoft.com/gp/contact_microsoft_customer_serv?&fr=1) as long as you have a valid proof of purchase.
otherwise, there is very little they can do.
You can refer to this article for more details:
http://office.microsoft.com/en-us/support/how-do-i-recover-or-replace-a-lost-microsoft-office-product-key-HA104172018.aspx
Thanks,
Ethan Hua CHN
TechNet Community Support

Super drive is not working after Restoring from Time Machine

well its pretty much the Subject actually, my imac giving me BlueScreen problem so i searched and posted question and the only Solution i got was to Re-install Leopard and i did that by using Leopard DVD and Restored my imac from Time Machine backup, But i got into new problem and now the TIME after restoring from the "Time Machine" my DVD ejecting EVERY CD,DVD etc. even the Leopard DVD which he reads happily.
I dont think its a hardware fault at all, but i'm not a "Genious". Any suggestion!

Issue solved with visit to Genius Bar.
As I understand it here are the steps the Genius did. Attempt to create the account (system preferences->users) with the same information. It will say it already exists. Very carefully read the options. One will say use the existing account. BE CAREFUL because one option will wipe your data.
If you need to do this it might be worth the trip to the Genius Bar as you could wipe your data. One precaution I took was to bring a full copy of that user account onto my desktop (from the backup immediately before the wipe) in addition to the one in the user folder. Once we verified that the account was working I moved the desktop copy to the trash and again verified the account (just to be safe).
Hope this helps someone else.

Where can i get a copy of the recovery disk after factory reset?

Hi, im wondering if anybody can help? i have a macbook thats a few years old and think it runs on 10.6 snow leopard. However i cant find the recovery disk. After sending it in to the shop to have more memory added, full back up onto an external hard drive and full factory resetits asking to be booted from the recovery disk. Can i download OSX 10.8 to drop onto a USB stick and load it onto the macbook? Thanks for any help

Hi Buddypup!
Drivers for your CanoScan N676U and Windows XP are available for download on the Canon website. Use the link below:
http://bit.ly/Y1AfBW
-Please note, you'll want to select the appropriate drop-down options from the drop down menus under "Drivers and Software" to obtain the Windows XP drivers.
Hope this helps!

My ipod touch is stuck up at Apple Logo, I have tried to update and restore through ITunes but no use, It stuck up again at Apple Logo with no Error, after restoring it showes your ipod is restore but still apple logo won't go

My ipod touch is stuck up at Apple Logo, I have tried to update and restore through ITunes but no use, It stuck up again at Apple Logo with no Error, after restoring ITunes showes your ipod is restore but still apple logo won't go, Due to new Laptop, I do not have any backup, therefore i have tried to select new Ipod touch and goes through step by step procedure but no use, Please help what to do?

i tried reseting my ipod today and had a similar problem... it wont be recognized by itunes, the only thing i havent tried is putting it into DFU mode, or the state that it is in when u recieve it telling u to connect it to itunes.i recommend putting it into DFU mode. http://www.youtube.com/watch?v=34v8HMC9B98 this should better explain it. if i find another way, ill keep u updated

I'm having a problem with logging into a FileVault-protected user account after restoring from Time Machine backup.

Hi all,
My computer had been running really slowly for a while, so I decided to erase the whole hard drive and reinstall the operating system, and then I was going to restore the files I cared about from Time Machine. The main account, which had all my documents and photos, was FileVault-protected. The last thing I did before erasing the hard drive was to run one last Time Machine backup. As far as I remember, I always ran Time Machine backups with the FileVaulted user logged in.
I don't remember whether I was using FileVault 1 or 2. I had been using FileVault 1, but I installed Lion as soon as it came out and I thought I had migrated to FileVault 2 at that point.
Once I erased the hard drive and reinstalled the operating system, I browsed the Time Machine disk and, within the Users folder, there was no folder for the main user account. When I tried to reinstall everything by restoring from Time Machine backup, I'd get the option for all the user accounts, but when I tried to log in with the main one I'd get the dreaded "You are unable to log in to the FileVault user account "User" at this time. Log in failed because an error occurred." Finally, when attempting to restore from the Time Machine backup again, I noticed something strange: After the computer got to about 10% done restoring, it declared itself completed successfully and rebooted.
I've tried a number of tips that came up from questions about similar issues on the Apple support forum, but had no luck. Is there any way to get these files back? Did they ever even get backed up?
Thanks.

Hroodbwai wrote:
I can't find it! not sure what's going on but the only folder shown is the " Shared" folder.
Did you have only the one user account? If there were others, they should also be in the "Users" folder. You probably won't have access to the files inside them, but they should be there.
From what can make out, it looks like it's not backed up any of the files for the filevault account. Can't see user folder when looking through previous backups in Time Machine galaxy view.
Are you doing that from a Finder window set to your internal HD, or your computer name? It should look something like this (with the Finder in List view):
|
|
I'd been logging out and backing up manually on a regular basis.
Scheduled backups should run normally; but they won't back up the File Vault sparse bundle, nor will any run manually.
The only time it's backed-up is when you actually log out.
You should have seen this window on logout:
|
|
followed by this one:
|
|
If you didn't see the second one, or cancelled it, the account wasn't backed-up.

I attempted to update my iphone5 to 7.1.1 There was an error and now my phone is erased. I have attempted to restore from the cloud and it propogates the apple id with an old one, and will not allow me to restore from a the cloud

I attempted to update my iphone5 to 7.1.1 There was an error and now my phone is erased. I have attempted to restore from the cloud and it propogates the apple id with an old one, and will not allow me to restore from a the cloud

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Also, do you remember what the error message said?

-20 error while restoring from backup

I am getting resotre faile (-20) error message while restoring the ipad from itunes, after upgrading to ios5. does anybody know what this message is and how to resolve

Cryslex wrote:
Thanks for the advice but I tried to reboot my computer from the osx disk and it said I could not run it off of the hard drive selected.
No, since it's not a complete system, it's not going to start.
You mentioned I had to erase the hd first but I don't know how to do that.
If you replaced your HD because of a problem with it, your best bet might be to try the full restore again, but select an earlier backup.
But if you want to erase your internal HD and install OSX, see the yellow box in #1 of Using Disk Utility.
Then see the REINSTALLING OSX section in the box for the version of OSX you're running in Installing the ''combo'' update and/or Reinstalling OSX.
Then you'll have two choices:
When your Mac restarts after installing OSX, you'll have the chance to transfer your data from the most recent backup. See either Using Setup Assistant on Lion or Using Setup Assistant on Snow Leopard or Leopard for detailed instructions.
Or, skip Setup Assistant and create a user account. When your Mac restarts again, use that account to reapair the backups, per #A5 in Time Machine - Troubleshooting. I suspect that's your best option, since it sounds like the backups are damaged.
If they can be repaired, you should be able to do the full restore. Or, you can use Migration Assistant, but that will result in an extra user account and the transferred accounts may lose permission to the backups. See Problems after using Migration Assistant for an explanation and some workarounds.
If they can't be repaired, most likely you can still restore selected items, via the "Star Wars" display, per Time Machine - Frequently Asked Question #15.

Why cant I download apps after restoring from a backup? How to fix?

After I restored my ipod from a backup a month ago, my ipod wont let me download apps. It says "Unable to download app at this time". The thing is I can download when connected to my computer, and when new apps are downloaded on my other devices, they auto-download onto my ipod (Like they did before the restore from the backup) How can I download apps again without connectig to my computer or downloading them on other devices?

Have you tried when connect to another network?
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings

How can I see my messages after restoring from backup?

I have 2.1gb of messages saved in my storage on my 4s but they're not in messages after restoring from backup.
How can I get all my messages back in my message app because I know they're their it's just a matter of getting them restored into the app.

When you restored your phone from an old backup, it wiped ALL data from your phone and replaced it with the data from that backup. It's like your phone went back in time.
Your data that was on the phone before you did the restore is now gone forever. There is no way to get these data back.

Even after resets get "The backup disk image "/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle" could not be created (error 22)."

HELP! "The backup disk image “/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle” could not be created (error 22)."
TC estimates over 750GB for full backup.
Late 2010 MBA is connected wirelessly to
802.11n (1st gen) TC that is connected via ethernet hub built into house to motorola router using charter.com for internet.
I have had same problem for over 150 days and multiple reboots, restarts in proper order, firmware updates, unplugs with 5min plus gaps, bypassing the tc and using external 500gb WD mybook via usb to time capsule, replacement of the WD mybook to new 2TB Free Agent GoFlex drive, etc, etc, etc! Note: I originally named my MBA hard drive MacBeth, but at some point months ago, it said backup already existed and system automatically created MacBeth (2), worked for a while, then stopped again, despite trying nearly daily.
I gave up and started using Carbon Copy Clone daily for just the 128gb on internal SSD of my late 2011 11" MacBook Air, but need to get past these time capsule errors to back up the external disk! Due to lack of space in MBA, I had long ago transferred both itunes and iphoto and all imovie/fcpx files to a 1tb external disk (WD Passport) that I keep in my bag with MBA. It is partitioned with 150gb for cloning the MBA, and over 750gb for media/itunes/iphoto/etc.
Also, I have endured months of "your hard drive is full" messages and system lockups, applying the solution given to me by genious bar (deleting all aol.com outboxes/recovered messages/spam/trash under library/mail/V2/Mailboxes folders, empty trash, restart....watch recovered hard drive space mysteriously shrink next couple days to zero.....repeat)
Due to lack of space, I had not been able to do javascript and other system updates. Yesterday, I noticed even safari bookmark bar had mysteriously emptied (not disappeared, I can hide and show the space where the bar used to be - it is just blank area with no data except for eyelass-book-topsites icons), so I transferred a few large quicktime movie files recorded with isight camera to the external disk, and freed up 20 gbs for the first time!
This got my hopes up yesterday because after I completed all system/software updates, suddenly the bookmark bar showed up and I was able to start the time capsule backup! It took overnight preparing for backup, but finally started and progressed to 12gb of the 100gb+ needed (i guess the update where it left off months ago for the estimated 750gb for the full backup?), then I put system to sleep and took it with me (thus leaving the wireless time capsule network as I do daily fully expecting it to continue when I returned home in the evening.) But alas, upon return, back to the "Time Machine could not complete backup, The backup disk image ".....sparsebundle" could not be created (error 22)" Ugh! More reboots, unplugs, 5min gaps....still Ugh!
So the problem continues...please help! Here are my settings:
About this mac:
Mac OS X V. 10.7.5
processor 1.6 ghz intel core 2 duo, memory 4 4g 1067 MHz DDR3
software up to date!
Airport Utility:
V 6.2 (620.33)
both internet globe and TC show green dots in graphic, however internet occasionally shows yellow then goes to green, but still gets error 22. Suddenly TC showed explanation mark and says lost connection and asked if I wanted to 'forget', gave same errors, then mysteriously went back to green, but still got error 22!.
Internet:
connection: connected, displays router address, 2 dns server, and domain name: charter.com
Time Capsule:
shows network, ip address, serial number, version 7.6.3, status: (green dot) Setup over WAN,
wireless clients: phones, macbooks (including this MBA), printers, wii
If you need other settings to help me, just ask! I have read a few of the other solutions in forums, but trying not to erase disks, especially since it worked for a minute yesterday!

To step sideways.. why not just use CCC to backup the 750GB of the hard disk to the TC.
You need to understand this is going to be a super slow process and each time you stop it.. it is going to give issues. CCC will at least do a more reliable job of it than TM.
I would also say.. this is going to be tough without ethernet. You need to understand the backup speed over wireless can be 10GB per hour.. that makes 75hrs to backup the disk. The air needs to run non-stop doing that.. without you touching it.
I would get another external drive.. plug that into the MBA and if you really want to use TM.. make a backup one to the other.. but CCC will again do a better job and work faster. It will be much faster than over wireless.
I am trying to think of ways around the issue of just speed.. but plainly you have lots of other issues.. being the simple unreliablity of the TM to identify the TC.
If you want to make this work.. give yourself a weekend.
Load 5.6 utility into the MBA..
http://support.apple.com/kb/DL1482
Take the TC back to 7.5.2 firmware. It is a really old version and latest firmware does it no good at all.
Wipe its hard disk using erase and start over.. give it new names for everything.
So call it TC
Set the wireless to 5ghz and name it TC5ghz
Use WPA2 Personal security. Use a 10 character passkey non dictionary.
At 5ghz you should get 2x the speed as at 2.4ghz but the air will need to be right next to the TC..
(alternatively buy the USB to ethernet cord apple have available.. it is $30 in the apple store and do it over pseudoethernet. http://store.apple.com/au/product/MC704ZM/A/apple-usb-ethernet-adapter That is the wrong store but you get the idea. )
WIth a fully clean system.. now do a full reset of TM.
See A4 http://pondini.org/TM/Troubleshooting.html
Direct the TM to back to the TC.. and make sure the external hard disk is not excluded.
Of course the TC has to be 1TB version to fit that much data.. goes without saying right.
Even over pseudo - ethernet this will take many hours.. and you basically have to leave it to work.. do not touch it.. make sure the MBA cannot sleep though.. turn off sleep.. beforehand.

After restoring from backup on iCloud, my photos have been "downloading" for 2 days with no progress at all.

After restoring from backup on iCloud, my photos have been "downloading" for 2 days with no progress at all. Everything else seems to by fine, however. I have all my apps, contacts, even my photostream back, but my camera roll has said "downloading 137 of 1,345" for two days. I really don't want to have to start over as the whole process took almost 3 hours. Help?

Someone mentioned that syncing with ITunes, making sure that photos are being synced - even with an empty folder, fixed the problem. I tried it and it didn't work for me. Anyone got any answers that don't include losing the photos or erasing and restoring from backup again?

"An error occurred while restoring from the backup.Files can't be restored"

My 4 month old MacBook Pro 15" running 10.6.2 lobotomized itself and I had to have a new HD put in it. I backed up the old one w/ TM on an external HD. I've tried (by the book, and with direct verbal guidance from the Help People at Apple) to restore the system and files but every time it gets to 10.2% in the restoration process and then I get this message: "An error occurred while restoring from the backup. Please restart." and under the frozen progress bar is the chilling line: "Files can't be restored." I've tried restoring from several dates on the TM backup list but it always stops at 10.2% completion. Help!

Hi.
Start by booting from your SL install disc, and selecting Utilities from the menubar, but before going on to +Restore System from Backups,+ instead select +Disk Utility.+
Make +*absolutely certain+* that your internal HD has the GUID *Partition Map Scheme* and the +Mac OS Extended (Journaled)+ Format (unless you're sure it should be +Mac OS Extended (Case-sensitive, journaled).+
Then do a +*Repair Disk+* (not permissions) on your Time Machine drive.
If that succeeds, quit Disk Utility, then continue with the full restore (per #14 in the FAQ).
But if that finds errors it can't fix, it's possible that +Disk Warrior+ can fix them. It's about $100, and is probably a good long-term investment, but there's no guarantee.
If all else fails, go back to Disk Utility and erase your internal HD, then install OSX. When your Mac restarts, use +Setup Assistant+ to transfer your users, apps, settings, and data from your backups (see #19 in the FAQ).
Then download and instal the "combo" update to get back to 10.6.2. Info and download available at: http://support.apple.com/kb/DL959 (or http://support.apple.com/kb/DL1017 for 10.6.3).
Be sure to do a +Repair Permissions+ via Disk Utility afterwards.

Satelite A500-ST5606 Digital Signiture Errors after restoring from the Recovery Disks.

Similar Messages

Maybe you are looking for