Satelite Pro L20 - LAN Not working after OS re-install

I have just recently replaced my hard drive and I used the product recovery disk etc.
WXP loaded perfectly and now my wired LAN does not seem to want to work. All it is giving me a limited or no connectivity.
I have tried to uninstall and re-install the drivers, manually enter the IP settings and still nothing will work.
I wondered if anyone else has had this issue before and could offer me any advice.
Many thanks in advance
M8KWR

Maybe you should check your settings at your router. Maybe some wrong DNS,Subnetmask, etc.
Did you already checked the cable?? Perhaps the cable is malfunctioning. Just cross-check it with another cable.
Would appreciate to get some feedback from you.
By the way, which operating system do you use?
Greetings

Similar Messages

HP Photosmart C6300 printer/scanner not working after Snow Leopard install

HP Photosmart C6300 printer/scanner not working after Snow Leopard install
Reinstalling etc does not work - does anyone else have the same problem or a clue as to how to fix this?

Keith,
I got a C6280 and the scanner does not work anymore. I am for 6 days in contact with HP. The last printer driver install form the apple web site does not open the image of HewlettPackardPrinterDrivers.dmg because of an invalid checksum. The skipping of the validation gives and error in the install.

HT3917 My apple wireless keyboard is not working after new batteries installed

My apple wireless keyboard is not working after new batteries installed.

Do you get a steady green light to say there is a connection. If not, are the batteries the right way round. Do you have a monitor to tell the batteries strength. Is there a reading. Are the batteries good quality ones, Duracell, Energiser or Apple rechargeables.

Touchsmart 320-1030 Touchscreen is not working after OS re-install

HDD crashed, and was replaced with new, re-installed system from factory recovery CDs, now touch screen does not work. I have re-installed the drivers to no avail. system Properties says under Pen and Touch: No Pen or Touch Input is available for this Display. It used to work before the hard drive crashed. Is there a setting in the BIOS? or something else I may have missed?
Thanks

Hello @ncmich2,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how the Touchscreen of your desktop computer is not working after replacing the Hard Drive, and I would be happy to assist you in this matter!
To re-enable the touchscreen features on your computer, I recommend re-installing the original software and hardware drivers that first came with your computer. This can be done by following the steps in this document on Using Recovery Manager to Restore Software and Drivers (Windows 7). To update the newly installed software, please follow this resource on Using HP Support Assistant (Windows 7).
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Excite PRO 3G connection not work after Android v4.3 update

Hello,
I live in Italy and on last Sunday (january 26th) my Excite PRO tablet (model AT10LE-A-10H) got the Android version 4.3.201121220.35.
After restart my wifi works fine, all other app work fine, but my 3g connection doesn't work, mobile network bar is empty and it says "no service".
My sim card is ok. I used this sim card before the system update and I didn't get any problem with Android 4.2.2.
Please help me.
Thank you

>After restart my wifi works fine, all other app work fine, but my 3g connection doesn't work, mobile network bar is empty and it says "no service".
Go to the mobile network settings and search again for the 3G network.
I had similar problem with my Android Smartphone and my o2 provider
I started new search, then I chosen the O2 again and then I could solve the problem.
In case this does not work for you, recommend you to reset the tablet back to default (factory settings)

Satellite Pro U400-15I - Sound Wheel not working after Windows 7 install

The sound wheel on my Satellite Pro U400-15l does nothing after the Windows 7 clean install from XP pro.
I used the recommended Software update tool downloaded from Toshiba. The VolumeIndicator.exe process is running and the sound works OK - just not under the control of the wheel! Also the Toshiba Power control is not there but this is not a problem.
Any suggestions welcome.
Bob Sheppard

Hi Syntax,
there is no option to add the volume control to the taskbar in the control panel.
The sound driver is 'Conexant High Definition Smart Audio 221'
Interestingly, when I click on the speaker icon on the taskbar and select the mixer option I get 3 sliders called 'Device','Applications' and 'Sound Volume Indicator of Toshiba Control'. If I move this slider with my mouse I get the indicator I am looking for ( The Toshiba indicator I had under XP). However, this slider only works as a 'minimum' for the other sliders.
Thanks for your help but I still would like that volume indicator back!
Bob Sheppard

Keyboard and Touch-Pad Not Working After Having to Install New Hard Drive

I had to install a new hard drive in my HP Pavillion DV9700t that has Vista Home Premium 64-bit. After going through the recovery process with backup disk the built in keyboard and touch-pad do not work. During the installation, an error message came up saying something along the lines of "the drivers are not supported by this verison of windows because they are unsigned." The drivers that had that error were "hpqkbfiltr keyboard filter driver," "HP remote control HID Device," and "hpqkdfilter driver." I tried to update the drivers for the keyboard from the hp website, but the keyboard and touch-pad still do not work.
My question is, where do I find the digitally signed drivers for the keyboard and touch-pad that Vista won't flag and disable?
Help please!

Sparkles,
Thanks for the suggestions.
When dealing with MS Fix It, I was choosing run. Upon further investigation on that site, there really isn't a scan that applies to my issue anyways I tried the .NET Framework repair tool, and that seemed to work. It told me to try re-running what I was having issues with, so I tried running the Windows PowerShell again, but again was faced with the following message "windows update standalone installer encountered an error: 0xc8000247." I went back to the .NET screen and hit "Next" because it didn't work, and that responded by saying they were going to submit logs to Microsoft. I won't hold my breath on that one.
I'm to the point where I honestly don't care anymore. I have no idea what to do, because doing a clean install with the discs HP sent me isn't going to help because they are just recovery discs, and not an actual Windows disk. This is the second hard drive I have had to put into my laptop and use those recovery disks on in the last 3-years. The built-in keyboard hasn't worked during that time frame on either hard drive. I don't think the recovery disks I was sent install properly. Not sure where to go from here. I spent way too much money on this laptop years ago having it custom built to handle all of my drafting programs, so I don't want to just kick it to the curb. I was looking into the possibility of just replacing it, but I cannot stand the Windows 8 interface.
I guess I should have fixed the issue with the keyboard on this hard drive before loading all of my programs. Between the recovery disk install, formatting of the hard drive, and installing all of my programs it took well over 12 hours. Not really looking forward ot that again Then there's shockwave and flash and all of the other goodies that my recovery disks won't restore anyways.
Sorry if this seems like a negative post, but I'm just tired of trying to no avail. Maybe I should just take it somewhere to get it looked at, but I can't see them being successful if the recovery disks won't help anyways.
Thanks for you help,
MadBuch

Siri does not work after IOS 7 install

Siri doesent work after I OS 7 install I hear it is a hardware problem. Siri works fine but then you download IOS seven and it stops working. Apple has told a couple people they have to buy a new phone. I hope thats not true. Because I will buy a new phone but it wont be apple if thats the case.

Hello, Dan.
Thank you for visiting Apple Support Communities.
I would recommend going through the troubleshooting steps in the article below when experiencing issues with Siri.
iOS: Troubleshooting Siri
http://support.apple.com/kb/TS4079
Cheers,
Jason H.

Secondary monitor does not work after OS X install

My secondary monitor does not work well after OS X install. The image on my secondary monitor is different even the screen svaer image is different and the mouse can not be seen.

Try the easy thing first - NVRAM reset:
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
If that does not work, post back with more info, including the version of Mac OS you are running. How is the external monitor connected, did it ever work, and from what OS X to what was the "OS X install" in your title?

Thunderbolt is not working after Mountain Lion installed

I'm putting this discussion again because the problem didn't solve like I thought !
As you can see from the title that I have a problem already after I installed the new OS X Mountain Lion. I got my thunderbolt to Hdmi adabtor connected to an LCD TV and it was working great with snow lepord. But after the I installed Mountain Lion. it won't even recognize that there is something connected and I don't see the options in my System Prefrences> Diplays like before.
I already run software update and it's all up to date and also done a PRAM reset and nothing changed.
It only ok for a couple of min. if I restarted it and without the sound working from the LCD TV.
Please I need help here.

Well I would have hit repair. This might be stemming from a deeper issue with the installation. I've never seen that dialogue box before, and if ignoring it and booting normally worked for you then I say you did the right thing.
however
I would, go to disk utility and then select your boot drive and verify and repair disks and permissions.
if anything else WEIRD should occur, you may want to go to the recovery partition of ML (cmd+R while hearing the boot chime) and reinstalling ML. That dialogue box you mentioned is strange and should be noted. A reinstall will probably fix whatever issue comes up.

Iphoto not working after time machine install

I have a first gen intel iMac and the hard drive had a sudden failure I was not overly concerned about my Data as I use time machine. I had a new Hard Drive installed and I used time machine to install back to snow leopard. all seems fine for a few days and every thing (software and hard ware (scanner)) was working fine. then I opened iPhoto to add a few new photos and all I get is the spining beach ball the library is 26 gig in size and was working fine before. I am at a loss as I still have all 9745 original photos on back up drive but not in order like in iPhoto and really don't want to recreate my library all over again. I've done disk permissions and only seem to have a problem with Java any body got any ideas?

Hi there Guys
I don't know if this is a true fix but my iPhoto 11 is now working iPhoto had an update and I did it to both my iPhoto programs (mac book and iMac) I then opened the not working librery on the laptop and it said the library need to be updated it did this and opened okay and all was working fine (I copied library on to a portable FireWire HD) when I copied it back to my iMac it said the same and went through the update and is now working fine.

Safari will not work after Snow Leopard Install

Safari does not work. It opens briefly, then closes. I get a message to "click reopen to open application again," but the same thing happens. Please advise.

Janice,
Quit Safari if it's open.
Locate this file. com.apple.safari.plist
/Users/YourName/Library/Preferences. Drag that file from the Preferences folder to the Desktop.
Launch Safari. If it launches without crashing, then that .plist file is corrupted. Drag it to the Trash, empty the Trash and restart your Mac.
If Safari still crashes...
Go to ~/Library/Caches/Safari and delete all the sub-folders within that one.
Go to /Users/YourName/Library/Safari and delete Home/Library/Safari and delete any of these files you have there:
Downloads.plist
History.plist
LastSession.plist
Carolyn
Message was edited by: Carolyn Samit

TS3479 quick time not working after snow leopard install?

Made video's on my iphone and loaded them to my imac. Video did not work in iphoto. No Quick time pop up. what happened? Snow leopard install.

You need to re-install iPhoto because it's missing bits of itself:
Library not loaded...
Reason: no suitable image found.
Looking at the missing files it's possible that it's missing from the OS. But start with re-installing iPhoto, and if that fails you'll ned to re-install the OS.
To re-install iPhoto
1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
2. Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name
3. Re-install.
If you purchased an iLife Disk, then iPhoto is on it.
If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only...’
Regards
TD

Ethernet LAN not working after upgrading to windows 8.1

After upgrading from Windows 8 to 8.1, my Ethernet LAN is no longer working. Wireless LAN connectivity is OK. I have run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I do not see a 8.1 driver listed for the Ethernet LAN.

You're very welcome. See if the recovery manager still works so you can roll back to W8. Please read this guide for how to use it. http://support.hp.com/us-en/document/c03489643 If it doesn't then you will have to order a set of recovery disks from HP, or you can install this plain W8 OEM software this guy has posted on a link. Lots of folks have used it successfully, which is why I posted it. https://docs.google.com/file/d/0B0W9PBigPy94aVJWSndyTFNFMzg/edit?pli=1 Then use this tool to make the iso file bootable to a DVD or 4+ GB USB flash drive. http://www.microsoft.com/en-us/download/windows-usb-dvd-download-tool Yes, that really stinks why you and I could not upgrade without an issue. I disabled about 5 or 6 devices in the device manager and the code 12 would not go away. I have no clue why the PC works fine on W8 but not on W8.1. My notebook is a few years older than yours and it worked fine on W8.1 but not on W10. Go figure...

Excite PRO 3G connection not work after system update

Hello, I live in Italy and on last Sunday (january 26th) my Excite PRO tablet (model AT10LE-A-10H) got the Android version 4.3.201121220.35. After restart my wifi works fine, all other app work fine, but my 3g connection doesn't work, mobile network bar is empty and it says "no service". My sim card is ok. I used this sim card before the system update and I didn't get any problem with Android 4.2.2.
Please help me I'm waiting for your help.
Thank you
Regards

This is the forums for Toshiba USA. Unfortunately, we don't have informaiton about your model. You may want to contact Toshiba in your region. You could check the Toshiba Europe forums.
- Peter

Satelite Pro L20 - LAN Not working after OS re-install

Similar Messages

Maybe you are looking for