Satellite 1410 standby/resume issue

Hello world,
this is my first post in the Toshiba laptop forums. I am facing an issue on my Satellite 1410, in which I would need some expert help.
The following happened:
I have installed Mythbuntu 9.10 (media center edition of Ubuntu) on my Satellite 1410 notebook (Mobile Celeron 1.8GHz / 512M / 160G). Everything went fine, I've been using it for some time.
I started watching a divx movie on my LCD TV connected to the HD15 port of the notebook and after a while, I closed the lid. The notebook went into standby and since then I have not been able to wake it up.
Everytime when I try to turn it on, the fan spins up, however the screen remains black, no disk activity can be heard and the power LED starts blinking in amber (1s on - 1s off).
I tried the following:
1. Took battery and AC power out, held power button for 90s - after turning on, still standby mode with spinning fan.
2. Took battery and AC power out for about 72 hours - still standby mode with spinning fan.
3. Took battery, AC power and CMOS battery out for about 90 min - still standby mode with spinning fan.
At this point I am a bit confused...
Why does the notebook go into such strange state that the fan is spinning, but the LED shows standby?
Where could this information be stored that it should go into this state (CMOS battery was removed for 90 minutes)?
Has anyone experienced similar issues?
Thanks in advance,
latrodectus

I have the same problem. I loaded Ubuntu 9.10 on my 1410. All went well until I closed the lid whilst the laptop was still switched on.
It does not matter what I do, but the laptop does not want to come out of hibernation.
I cannot even boot up with a CD or other source.
The screen does not even give option to go into the BIOS
Thanks

Similar Messages

Satellite 1410-604 - BIOS update Incorrect BIOS update in the web?

Hi there again!
Now with a new and weird matter.
We all know that old say... "If it is not break, don't fix it". And if you put it into more informatic terms, "specially if it is a BIOS".
Yes, we all know that the BIOS is something quite dellitate to handle. For some reason we normally feel like if we were handling something like nitro-glycerine, or some radioactive product. And this is because we all know what is being put in risk in that moment: our (or sometimes others) computer, the full system could end as dead as some pieces of metal, plastic, and wires.
Well. I passed through all of that more than ten times in my life, and only once it went wrong. But since that old motherboard was already dead, It was not important. But I allways was EXTREMELY care. I allways cross checked everything before doing anything, allways got a backup and a way to restore that backup... and allways did this in COMPAQ systems, that were prepared that way. Updating a BIOS was just about preparing a disk, turn on the PC with the disk in the diskette drive, and wait. And if you didn't like the results, you simply click "return to previus BIOS" and that was it... very nice. And easy.
Few days ago, a friend brought me a Toshiba Satellite 1410-604 to solve some issues that were driving him crazy. After removing an expired Norton Internet Security, install avast and scan, I found more than one hundred files infected with a wide variety of virus, malware, trojans, and whatever you could imagine. Avast removed them all, but the remains of the operating system was so unstable that we decide to format and install from scratch.
I asked for the restoration disks, that obviously he don't have because they were lost in one of his movings. After we got the confirmation from Toshiba reps that there are no recovery disk available for this model, because it is too old, we decided to install from scratch like any other normal PC, and resigned to loose some of the utilities that come with that CDs and that are not available for download in the website.
I downloaded all of the software available for this model, including two BIOS updates. (Actually only one update, but in two versions: Windows and Traditional), and prepared a CD with all the drivers and programs just like if it were a brand new system install. And everything went very well, no problems at all. Until we got to the Wireless LAN card, but that is another issue that is already solved (the mini PCI card for the WLAN does not support WEP or WAP encription, and it is not possible to connect to any wireless LAN encripted).
At this point, and when I started configuring and enabling PCMCIA devices, and USB devices (this computer only supports USB 1.1 not 2.0) I discovered this text in the Toshiba Website:
"This Bios Update adds increased functionality to your system.
(BIOS is an acronym for Basic Input and Output System. This program is stored in a Read-Only Memory chip on the motherboard.
When the computer powers up, the BIOS is launched to perform various start-up functions.)
For detailed update information please refer to Toshiba BIOS-Update Information"
(you can find this here:
[http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=EU] you have to look for:
Archive
Satellite
Satellite 14xx
Satellite 1410-604
PS141E
Quite specific. Isn't it?)
According to the information in that same website, the BIOS available fits the following models:
"Satellite 2410-414, Satellite 1410, Satellite 1410-654S, Satellite 1410-814, Satellite 2410-303, Satellite 2410-304S, Satellite 1410-354, Satellite 2410-601, Satellite 1410-401, {color:#ff0000}*Satellite 1410-604*{color}, Satellite 2410-404, Satellite 1410-301, Satellite 1410-304, Satellite 2410-S403, Satellite Pro 2100, Satellite 1410-S203, Satellite 2410-304, Satellite 1410-554, Satellite 1410-S102, Satellite 1410-354E, Satellite 2410-703, Satellite 1410-303, Satellite 2410-S203, Satellite 1410-801, Satellite 2410-603, Satellite 1410-902, Satellite 1410-313, Satellite 1410-802, Satellite 1410-714, Satellite 2410-354, Satellite 2410-514, Satellite 1410-614, Satellite 1410-704, Satellite 2410-515, Satellite 2410-504, Satellite 2410-702, Satellite 1410-S103"
Yes... it's there!
Now, when you go to the "Toshiba BIOS-Update Information", you get:
"FAQ Ref.: TRO0000000b07
A BIOS update is a {color:#ff0000}*relatively simple operation and can be carried out by most competent computer users*{color}. All BIOS upgrades can be obtained from "BIOS Update" Download Section click here..
Note: The BIOS files are machine specific so the correct BIOS for your machine must be used."
Please note that Toshiba does not disencourage the handling of BIOS, on the contrary: they even encourage people to do so. This is not necessary bad, but at the same time they encourage people to 'play around' with such a delicate matter, at the end of that same page, in little letters they say:
"Toshiba provides this information "as is" {color:#ff0000}*without warranty of any kind*{color}, either expressed or implied, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose. Toshiba shall not be responsible for the topicality, correctness, completeness or quality of the information provided. {color:#ff0000}*Toshiba is not liable for any damage caused by the use of any information provided, including information that is incomplete or incorrect*{color}."
This should trigger yellow alarms in our minds.
+"Human error is inherent to humans, and it is not possible to erradicate. It will allways appear, sooner or later" (Prof. James Reason).+
And finally I made the mistake. Even though I read that warning, I remembered all those successfull BIOS update with COMPAQ, and relied in Toshiba. That update was available there, and Toshiba was telling me that it was for this computer. Great!
So finally I unplugged all devices (USB), removed the PCMCIA (WLAN),plugged the battery charger to avoid any possible battery problem, restarted windows, and then from within windows I started the updater (windows version, as recommended by Toshiba). Everithing looked fine, nothing different of what I used to see on those old COMPAQs.
As warned by the updating program, the system was going to reboot. And actually it did so.
Windows closed quite normally (a bit quicker than normal, but without errors, and since there were no other programs than the essentials -even the antivirus was not running-), the computer switched of, all lights off (normal), and then it switched on again...
{color:#0000ff}*BEEEEEEEEEEEEP... BEEEP... BEEEEP...*{color}
OMG! I never espected something THAT bad. 3-1-1!
And now... What a 3-1-1 stands for here? Award BIOS would mean no video card or deffective video card, but it is not true, since it was working up to 20 seconds ago. It must be the BIOS.
It never came again to life. It is still beeping 3-1-1.
But now comes the investigation of the human-factors involved in this accident.
I found I commited the following failures:
*(1)* To rely in the manufacturer, even though they WROTE their information could be wrong or incomplete. (BAD if I were a QA&QC inspector).
*(2)* I didn't cross checked deeply enough (until it was already too late).
*(3)* I didn't looked previously for the way to make a backup of the BIOS, in order to restore should anything go wrong.
*(4)* Let Toshiba lead me to a path I didn't want to walk, just because of their offer of "increased functionality".
*(5)* Beleave in Toshiba when they said "relatively simple operation and can be carried out by most competent computer users"... they never said it is failproof.
Then I started the most interesting part of the investigation.
{color:#0000ff}*"What went wrong?"*{color}
Obviously, the BIOS update failed somehow, somewhere. And I wanted to know what and where.
First thing I discovered was that there are another search engine in Toshiba called "askiris" ([http://askiris.toshiba.com]) and I looked there in order to see if for any chance I could get the old 1.20 BIOS version that was installed originally in that machine.
And I found something... VERY interesting:
bq. {color:#800080}*From: * \\ {color}{color:#800080}* ACPI Flash BIOS version 1.10 for Satellite 1410/1415/2410* \\ {color}{color:#800080}* bios for these models. TAIS. Downloads. DL. 105481 289838 289838 ACPI Flash BIOS version 1.10 for Satellite 1410/1415/2410. 2002-10-04. 105589...* \\ {color}{color:#800080}* Published 10/4/02* \\ {color}{color:#800080}* From: * \\ {color}{color:#800080}* ACPI Flash BIOS version 1.40 for Satellite 1410/1415/2410/2415* \\ {color}{color:#800080}* FDD Version 1.30 TAIS. Downloads. DL. 105481 357972 357972 ACPI Flash BIOS version 1.40 for Satellite 1410/1415/2410/2415. 2003-01-31. 105589 PUB...* \\ {color}{color:#800080}* Published 1/31/03 | Rating:* \\ {color}{color:#800080}* From: * \\ {color}{color:#800080}* ACPI Flash BIOS version 1.20 for Satellite 1410/2410* \\ {color}{color:#800080}* error message during BIOS TAIS. Downloads. DL. 105481 305240 305240 ACPI Flash BIOS version 1.20 for Satellite 1410/2410. 2002-11-01. 105589 PUB...* \\ {color}{color:#800080}* Published 11/1/02 | Rating:* \\ {color}{color:#800080}* From: * \\ {color}{color:#800080}* ACPI Flash BIOS version 1.30 for Satellite 1410/1415/2410* \\ {color}{color:#800080}* 1) Changed the content TAIS. Downloads. DL. 105481 330963 330963 ACPI Flash BIOS version 1.30 for Satellite 1410/1415/2410. 2003-01-03. 105589...* \\ {color}{color:#800080}* Published 1/3/03 | Rating:* {color}
Those are: V110, V140, V120 and V130 for series 1410/15 and 2410.
GOOD! Or not?
Let's take a look:
First thing I did was download everything all four files.
Then I took the same version that made the crash: 1.40
Than I uncompressed the file, and I found:
06/05/2009 00:17 <DIR> .
06/05/2009 00:17 <DIR> ..
31/01/2003 08:38 1,605,632 11410v14.iso
31/01/2003 08:38 511,764 1370D14.EXE
{color:#ff0000}*08/01/2003 17:03 724,480 2410a9v140.exe*{color}
09/01/2003 09:32 250,663 biofca9t.com
08/10/2002 05:26 30,697 chgbiosa.exe
31/01/2003 08:36 1,087 instinfo.bat
13/05/2002 15:25 378,175 launcher.exe
31/01/2003 08:36 433 launcher.ini
06/05/2009 00:17 0 list.txt
31/01/2003 08:36 14,768 readme.com
*{color:#ff0000}31/01/2003 08:36 12,513 readme.txt{color}*
11 archivos 3,530,212 bytes
3 dirs 9,404,600,320 bytes libres
And I got my first surprise here: There is a {color:#ff0000}*README.TXT*{color} that was not present in the file I downloaded previously from the drivers repository.
So I went to the readme.txt and I found this:
"README.TXT 01-31-2003 CDC
Flash BIOS version 1.40 for Satellite 1410
This BIOS is applicable to the following models:
Satellite 1410-S105
Satellite 1410-S106
Satellite 1410-S173
Satellite 1410-S174
Satellite 1410-S175
Satellite 1410-S176
Satellite 1415-S105
Satellite 1415-S106
Satellite 1415-S115
Satellite 1415-S173
Satellite 1415-S174
Satellite 1415-S175
Satellite 1415-S176
Satellite 2410-S203
Satellite 2410-S204"
Please note that the model 1410-604 is *NOT* listed.
I thought "well, it must be another archive..."
But then I realized of a name that sounds familiar, it was there, in the directory where I uncompressed this 1.40 file, and the name is:
{color:#0000ff}*2410A9V140.EXE*{color}
So I took the other file, the BIOS_Win update, and I discovered that the file name is:
*{color:#0000ff}2410A9V140.EXE{color}* (Ups!)
So I uncompressed it again, to find:
El volumen de la unidad D no tiene etiqueta.
El n£mero de serie del volumen es: 8838-E175
Directorio de D:\Shared\diskette\2410A9v140
06/05/2009 00:43 <DIR> .
06/05/2009 00:43 <DIR> ..
*{color:#0000ff}09/01/2003 09:32 _250,663_ BIOFCA9T.COM{color}*
17/07/2002 03:38 35 biosupd2.ini
13/07/2001 13:22 6,277 chgbios2.vxd
*{color:#0000ff}08/10/2002 04:26 _30,697 _CHGBIOSA.EXE{color}*
09/11/2001 09:14 134 clean2.reg
17/07/2002 03:35 342,064 install2.exe
16/07/2002 06:55 241,664 nchgbios2.exe
18/08/2001 11:41 3,435 nchgbios2.sys
23/10/2001 18:55 11,476 nchgbios2NT.sys
26/08/2001 09:00 49,152 nchgbios2svc.exe
13/07/2001 17:05 49,152 tbdecode.dll
14/03/2002 06:42 49,152 TCHGBIOSInfo.dll
21/06/2002 11:25 1,796 tosclean2.bat
09/11/2001 12:01 967 tosclean2.pif
21/06/2002 11:34 1,841 toscleanAUTO2.bat
21/06/2002 11:44 1,796 toscleanSMS2.bat
21/06/2002 08:51 2,038 tosntclean2.bat
21/06/2002 08:51 2,084 tosntcleanAUTO2.bat
21/06/2002 08:52 2,038 tosntcleanSMS2.bat
20 archivos 1,046,461 bytes
2 dirs 9,402,793,984 bytes libres
No readme file...
Then another question arised in my mind: What about the other 1.40 file? What does the other 2410A9V140.EXE have inside?
This:
El volumen de la unidad D no tiene etiqueta.
El n£mero de serie del volumen es: 8838-E175
Directorio de D:\Shared\diskette\comparacion_toshiba\askiris\241 0a9v140
06/05/2009 00:46 <DIR> .
06/05/2009 00:46 <DIR> ..
*{color:#0000ff}09/01/2003 09:32 _250,663 _BIOFCA9T.COM{color}*
17/07/2002 03:38 35 biosupd2.ini
13/07/2001 13:22 6,277 chgbios2.vxd
*{color:#0000ff}08/10/2002 04:26 _30,697 _CHGBIOSA.EXE{color}*
09/11/2001 09:14 134 clean2.reg
17/07/2002 03:35 342,064 install2.exe
16/07/2002 06:55 241,664 nchgbios2.exe
18/08/2001 11:41 3,435 nchgbios2.sys
23/10/2001 18:55 11,476 nchgbios2NT.sys
26/08/2001 09:00 49,152 nchgbios2svc.exe
13/07/2001 17:05 49,152 tbdecode.dll
14/03/2002 06:42 49,152 TCHGBIOSInfo.dll
21/06/2002 11:25 1,796 tosclean2.bat
09/11/2001 12:01 967 tosclean2.pif
21/06/2002 11:34 1,841 toscleanAUTO2.bat
21/06/2002 11:44 1,796 toscleanSMS2.bat
21/06/2002 08:51 2,038 tosntclean2.bat
21/06/2002 08:51 2,084 tosntcleanAUTO2.bat
21/06/2002 08:52 2,038 tosntcleanSMS2.bat
20 archivos 1,046,461 bytes
2 dirs 9,402,781,696 bytes libres
*{color:#ff0000}They both have 20 files, and 1,046,461 bytes. I asumed they are both the SAME file{color}*.
And the readme file does not list the model 1410-604 in its readme file, therefore I cannot explain this except as a mistake from Toshiba. *{color:#ff0000}They put an incorrect BIOS in their website, and suggested the update, and somehow leaded to this kind of errors.{color}*
(Except in the case that one of those models is a different name of the 1410-604 model, and if it is the case... now I don't know why this BIOS do not work with this computer).
The worst part is that neither of those other files (V1.10, 1.20 and 1.30) lists the 1410-604, therefore there seems no possible workaround for this problem. I need an original v1.20 for this CMOS, and Toshiba seems not to have it. They offered me to solve the problem, by leaving the notebook at an ASP, and paying only 95€ for the work and about 280€ for a motherboard replacement, I will get it solved. But they offer no warranty of their possibilities because is a model 'too old' and 'discontinued' and with 'no support'...
In other words, they said "don't bother with this, just go out there and buy a new one" (something absolutely out of my scope in this crisis-time) :P
Thank you for reading soooo far.
Now what I need is to get any ideas of a workaround for this, my ideas are:
(1) This CMOS has a boot-part that still works (it allows a roll-back if you have the appropriate file). So I need a good BIOS to burn into the CMOS, from the VERY SAME model (a BIOS backup) but the backup must be adequate for the burning program (CHGBIOSA.COM).
(2) It is still possible that the BIOS could be OK but the data on the CMOS got somehow corrupted. If so, clearing the CMOS could solve de problem. But I was not able to find a clear cmos button from outside, and after disasembling I took of the battery, with no good results. I have to try leaving the MOBO without battery for longer period (I left it about 20 seconds) just in case 20 seconds don't allow all the capacitors to fully go to zero values. I have not much hope in this point.
(3) Try to get a REAL good update from Toshiba. I contacted several times technical support, and I was able to verify they are only phone-operators, with a script in front of them, and when the problem goes-out-of-scope they fall always in the same answer: "you have to go to an ASP". I still have a low hope to find someone who really knows a bit, and could enlighten with a good BIOS to put in this disks.
(4) As far as I could find, this BIOS is not from any known BIOS-maker. It seems it has been developed by Toshiba (own brand), therefore the Crisis Recovery Disk from Phoenix will not be of any help here. As well as any other BIOS recovery tool not designed for Toshiba's BIOS. But I'm open to any ideas, that could be tested more or less safely. (Remember that the 'BIOS-BOOT-PART' feature is still working, I don't want to loose this only possibility of redemption).
Wwwaaaaoooowww... what a long-post falks! Sorry for that!
Forgive me, but I wanted to be really clear.
Should anyone give some hints or advice, will be greatly appreciated.
Please don't say what I shouldn't do... I already know that. I already researched and already found my mistakes, in order not to repeat them. Now I need to move on, to advance, and to try to solve this, or at least learn how to solve similar things. As much as possible.
Thank you again, in advance, and sorry again.
FenixDigital
Message was edited by: Fenix_D
Changed subject to beter reflect what is the matter about (apparently erroneous BIOS file in Toshiba download center).

Well. 
 
It's not dead, certainly. 
 
The steps that I put in my procedure were: 
 
--> There are two memory sims, that I am going to identify as M1 and M2 
--> There are two memory banks, that I am going to identify as A and B 
 
Next step in order to identify if there are some module or bank that is not working properly are: 
 
The modules were installed as: 
 
M1 --> A 
M2 --> B 
 
1--> Boot without any memory chip. 
 
<blockquote>
A--> X 
B--> X 
</blockquote>
 
2--> Boot with ONE module 
 
<blockquote>
A-->M1 
B-->X 
</blockquote>
 
3--> Boot with the OTHER module 
 
<blockquote>
A--> X 
B--> M2 
</blockquote>
 
4--> Boot with BOTH modules swapped: 
 
<blockquote>
A--> M2 
B--> M1 
</blockquote>
 
5--> Boot with ONE module swapped: 
 
<blockquote>
A--> M2 
B--> X 
</blockquote>
 
6--> Boot with the OTHER module swapped: 
 
<blockquote>
A--> X 
B--> M1 
</blockquote>
 
At this point I got a great difference. It booted, finally. But in order to make a diagnostic, I have to complete the full test, and the results were: 
 
1--> Boot without any memory chip. 
 
A--> X 
B--> X 
 
NOT BOOTING Actually the computer not even tries to read the disk. Only the power led turns on, but even prior to press the 'on/off' button. I think this indicates 'no memory installed'. I would have expected a post failure beeps, but there were no beeps at all. 
 
2--> Boot with ONE module 
 
A-->M1 
B-->X 
 
BOOTED NORMALLY Well. This obviously means that the 3-1-1 beep code means memory error, or one bank failing of two installed. Now I didn't know if the problem was the module, or the bank B. 
 
3--> Boot with the OTHER module 
 
A--> X 
B--> M2 
 
NOT BOOTING Just like the condition in 1. Like no memory installed, therefore there are two possibilities: The bank B is not working, or the memory module M2 is not working. 
 
4--> Boot with BOTH modules swapped: 
 
A--> M2 
B--> M1 
 
NOT BOOTING Just like previous to test condition. Beep code 3-1-1, no boot at all. 
 
5--> Boot with ONE module swapped: 
 
A--> M2 
B--> X 
 
NOT BOOTING This was the important test, because it finally let me determine that the problem is at the module 2 (M2) not at the bank B. But still there could be a failure IN THE BANK B and IN THE MEMORY MODULE 2. Have to do the other test. 
 
6--> Boot with the OTHER module swapped: 
 
A--> X 
B--> M1 
 
BOOTING NORMALLY This really confirmed there is nothing wrong with ANY bank, but one of the modules is not working, actually is not being even detected. This is quite weird, because this computer was working perfectly with those two modules, and in the moment of the BIOS upgrade it seems to fail... How come? 
 
Something weird happened here. I don't know what, but something ruined one memory module (fortunately only one), what I would like to know now is what happened. But at least I have the machine running, with very low memory, but running. 
 
What I am thinking now is what about this BIOS upgrade makes the motherboard not to recognize one of the modules for some reason? 
 
<img class="jive-emoticon" src="images/emoticons/happy.gif" border="0" alt=":)" /> 
 
I will continue my research, but certainly the memory made the difference. 
 
I am not sure why I didn't discover this before, I think I didn't perform this test before, for two reasons: 
 
(1) I tried to boot with no memory, and this was impossible, so I assumed that the problem was not at the memory. 
 
(2) When I heard the beep code (3-1-1), somewhere I read it was a video problem, and I asume most probably it was a video problem (since no video at all was being displayed) but I should have take into consideration that Phoenix BIOS also means with the same 3-1-1 a DMA problem (memory problem). 
 
Okis... It's a pitty having to wait so much between a post and it's approval. I posted my answer two days ago, and since it didn't appear, I believe It didn't upload, so I replied again, and also didn't appeared... until now. It is obvious that a moderator approval is required. That's why I have to wait 24 hours or more to read my post. This slows this forum effectiveness. 
 
Thank you very much for your help. I'll keep you informed. Until we get to a final diagnosis and solution.

SD-2212 Drive doesnt read some DVDs - Satellite 1410

Hello every1,
I have Satellite 1410-604 for more than 2 years, with forementioned combo drive...
It serves me well, except that it doesnt read some of the types of dvd-medias, and I use only high quality Verbatim dvds...
It only happens in last few months. It is not my primary computer but it is at use in my home, and it really bugs me that when my sister or father takes the new Sattelite Pro A60 on the road(its battery is better) I cant use latest discs on this one. So if there is some firmware upgrade, cause i cant find it on this site...
Thanks in advance...

Hi
I dont think that the firmware update will solve this issue because this driver has recognized this DVDs a few times ago.
Furthermore I dont found any firmware for this drive on the Toshiba website.
But check if the drive removing procedure will solve this problem. So for this please go to device manger and remove the drive. After new booting the OS should recognize the drive again
Bye

Format C Drive on my Satellite 1410

Hi All,
I was told that it is better to format your c:-drive prior to do a re-install of Windows. Is this true?
I have a Toshiba Satellite 1410, Windows XP home edition and need to re-install windows since as per my ISP, my laptop seems to be used as an Open Relay.
What are the steps to take for a Format of your hard drive anyways. I saw an article on Microsoft (http://support.microsoft.com/default.aspx?scid=kb;en-us;313348) and that worried me a bit. For one how can I check the BIOS settings...??
Appreciate any advice in this matter!
Thanks in advance,
Ellen

Hi Ellen
If you want to reinstall your notebook please use Toshiba Recovery CD and the C drive will be formatted automatically. I suppose that you have more partitions on HDD. In this case please use Expert mode installation because on this way it is possible to install OS on just one partition.
More details you can find on http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=2513&tstart=30 .

Wireless key is not working on my Satellite 1410

I have Satellite 1410-303 system. I installed one broadcom802.11b/gwlan its working properly but I cannot off and on by fn-f8 key using. I want solve the problem.
Can anybody offer a solution?

There is a list of supported PnP-IDs in the registry under HKLM\Software\Toshiba\Wireless Hotkey.
Look for the PnP-ID of your Wlan card in the device manager and overwrite one of those you don't need in the registry.

I want to install the new HDD for Satellite 1410-303

Can I install the HDD MK8032GAX (80Gb Toshiba 2.5" IDE, 5400rpm, 16Mb) into my Toshiba Satellite 1410-303? Will BIOS detect it?

Unfortunately there is no official document about that because HDD upgrade is so-called dealer option and because of that there is no precise info about HDD upgrade. According to notebook specification, this notebook model is delivered with 20GB HDD.
I am pretty sure you can use 40 or 60 GB without any problems. About 80 GB I will not speculate but maybe someone has already tested and will post here in next few days.
Good luck!

Satellite 1410-902: How to remove a HDD

Hi. Does anyone know how to remove a HDD from a Toshiba Satellite 1410-902?
Opening the panel there it is the HDD, but there is no clear way to get it out...I don't want to force.
Thanx for the help.
Luca.

Hi
The HDD slot is placed at the bottom of the unit. You have only to remove the screw which secures the slot cover. Then you can simply remove the HDD.
But be careful.

What Wlan miniPCI cards can I install on Satellite 1410-604

Hi,
What types of minipci cards i can install into this laptop?
In users manual there is information, that minipci slot in satellite 1410 is compatible to Type III A.
Will this card http://www.gigabyte.com.tw/Support/Communication/FAQ_Model.aspx?ClassValue=Communication&ProductID= 985&ProductName=GN-WI01GS work of i insert it?

I have goggled a little bit and found a XG-601 802.11b/g, 54Mbps Mini-PCI Wlan card.
According to the description this card supports a 32-bit, Type III A interface.
Also the Intel PRO/Wireless LAN 2100 3A Mini PCI Adapter supports a IIIA interface.
These are one of the first miniPCI Wlan cards which were designed for the Wlan usage and support several Wlan protocols

Does Satellite 1410-401 supports USB 2.0?

I cann't find anywhere whether Satellite 1410-401 supports USB 2.0. If not - what would be the recommendations in order to add USB 2.0 support for my notebook?
Thank you in advance.
Andrianas

Hi,
sorry I have to disappoint you. The Satellite 1410-401 has only 3 USB 1.1 ports!
You can add USB 2.0 with external solutions like PCMCIA USB 2.0 Cards.
Bye Sammy

Satellite 1410-714: What CPUs are compatible?

I have Intel Mobile Celeron 1.6GHz in my Satellite 1410-714. What CPUs are compatible ? Please write typ (Celeron or P4-M), speed, package and sSpec number. I found CPU Mobile Intel Celeron Processor 2.20 GHz SL73Y (http://processorfinder.intel.com/details.aspx?sSpec=SL73Y) - but I don't know if this CPU will fitt to my Satellite.
Thank to all :)

Hi
This notebook must be a little bit older. Am I right?
There are not many information when I try to google for this notebook model.
But I think I have found what you looking for :D
The motherboard should be compatible with this CPUs:
Mobile Intel Celeron Processor 1.6GHz, 1.7GHz, 1.8GHz
Processor core speed: 1.6GHz at 1.45V
Processor bus speed: 133MHz
Mobile Intel Pentium 4 Processor-M 1.7GHz, 1.8GHz, 1.9GHz, 2.0GHz, 2.2GHz featuring Enhanced Intel SpeedStep Technology
Processor bus speed: 400MHz
But you know, the faster CPU will produce more warmness and therefore the temperature will increase. This could lead to the overheating.

Satellite 1410-S173 continually freezes when using wireless adapters

I just recently got a hold of an older Satellite, the 1410-S173 model. Runs really good as long as you dont plug in a wireless adapter. Have tried both a USB USR wireless G adapter and Windows XP just BSODs fairly quickly. Tried a Encore Elec. 802.11g Wireless PC Card Adapter in the slot and that one will at least work, but for some reason when it is in the machine about every other minute or so, the whole system just freezes dead for about 5-10 secs and then un-freezes. It continues this as long as you have the adapter in. You take the adapter out and use an ethernet cable with the internal NIC and runs just fine, no locks. I have reinstalled Windows fresh with a formatted drive and same thing. I have reseated memory, reseated HDD. Ran diags and still same thing. Anyone have an idea for me ?
Appreciate Any thoughts !!
DavGMac

Satellite 1410-S173
Just a shot in the dark..
That's a really old model. Perhaps you should stick with the a or a/b adapters.
The internal card recommended in the specs above is 802.11b.
-Jerry

Satellite 1410-902: Which DVD drives are compatible?

My CD in Toshiba s1410-902 is broken and I would like to change it to DVD reader or DVD recorder. The problem is, that not all IDE CD/DVD drives will work with this Toshiba. BIOS accepts only definite drives some of manufacturers, but I don't know which one.
Where can I find the coplete list of copmatible DVD drives for this model of Toshiba?

Hi
If you will buy a drive for your notebook you have to check the physical size of the drive.
The drive settings (master/slave/csel) are very important because you cannot reset these settings like on the normal desktop PC drive.
I have found this CD-RW/DVD-Rom combo drive: P000352490
This drive should be compatible with Satellite 1410.
But of course, you can contact the ASP in your country if you want to order supported parts.

Satellite 1410 dvd rom / cdrw combo replacement procedure

How do you replace the dvd/cdrw combo drive in a Satellite 1410?
There is only one visible screw on the bottom that is fastened to the drive.
I also removed the hard disk and battery, and the other covers on the bottom and did not find any other screws.
I removed the keyboard and did not find any additional visible screws that hold in the cd drive.
Does anyone know the removal procedure, or have a link to a maintenace manual?

lahave wrote:
How do you replace the dvd/cdrw combo drive in a Satellite 1410?
There is only one visible screw on the bottom that is fastened to the drive.
I also removed the hard disk and battery, and the other covers on the bottom and did not find any other screws.
I removed the keyboard and did not find any additional visible screws that hold in the cd drive.
Does anyone know the removal procedure, or have a link to a maintenace manual?
Toshiba doesn't make maintenance manuals available to anyone other than ASPs.
Unofficial instructions are at:
http://www.irisvista.com/tech/laptops/Toshiba1415/sat1415_1.htm

990fxa-gd80 resume issue

Hello, i hope someone among you good guys can help me with a very annoying issue i am experiencing in my system, that is driving me mad and that i could not solve in a month of tries. I own an HTPC based on the following configuration:
AMD Phenom II X4 945 CPU
MSI 990FXA-GD80 M/B
8Gb Corsair XMS3 DDR (2x4Gb)
Corsair AX-650 PSU
Samsung 256Gb 830 SATA SSD (2 partitions, system + data), AHCI SATA mode
Seagate 3Tb Barracuda SATA HDD with GPT table
ATI HD 5750 video card (2 displays attached)
Terratec Cinergy DVB-S2 card
Hauppauge HVR-2200 DVB-T card
Silverstone LC-16m case with Imon VFD + Imon Pad remote and USB card reader
Internal serial port, 1394 and eSATA ports enabled
Logitech USB Webcam, USB speakers and USB G110 illuminated keyboard
Toshiba laser mouse
Windows 7 x64 sp1, windows Media Center + DVBLink TV source, MST and various other programs.
Hibernation disabled
No overclok
I used this HTPC with much satisfaction from nearly 1 year, never experiencing an issue: i used to keep it in S3 mode 24/7 and it always got out from S3 state to record TV programs without any problem.
I installed the second drive, the 3Tb Seagate Barracuda, the first week of september. Then a day between the firsts of october i installed Mediaportal to give it a try; fearing system modifications by that software, i saved a backup image in my second drive. After a pair of days (or maybe at that time i noticed it for the first time), the issue has started.
The issue consists in a strange system freeze when the HTPC tries to wake up from S3: when the HTPC tries to exit S3 state the case led gets on, the HDD led blinks once or twice and then fans start running loudly and the HTPC freezes BEFORE the display can show any image (it remains black and goes to power saving mode) - power led on and HDD led off. No blue screen (the display is off). No memory dump. Keyboard's leds off. No manual crash dump possible. All i can do is keep power switch pressed until system complete shutdown.
But the really strange thing is that it happens ONLY once or twice a day, in the rest of the times the HTPC gets to wake up from S3 normally without any issue: it usually wakes up from S3 a number of times per day (7/8 minimum), but only 1/2 times the freeze issue happens (more often early in the morning or around twilight, seldom in other time slots)... Also, when on, the HTPC runs flawlessly as ever.
Thinking MP was guilty in some way, i restored the backup image but unfortunately the issue didn't disappear! So MP was no to blame... something different had happened to my PC...
I think you can understand that such an issue is really serious for an HTPC, because it makes it really untrustable for scheduled recording work: often recordings fail because of the HTPC freezing when it tries to resume... my wife is really sad about it...
Trying to solve the issue, i made the following:
running memtest and video card memory test - no error found
change nearly every MST options - no effect
reading carefully W7's event viewer logs after and between freezes - nothing found that could clarify the issue
changing all ACPI and power related BIOS options (C3 support, EUR 2013, CPU phases, DDR phases, shadowing, etc...) - no effect
updating BIOS and all drivers - no effect
disabling cool'n'quiet - no effect
unplugging Segate 3Tb HDD - no effect
unplugging all external and internal USB devices (except mouse) - no effect
uninstalling ATI video card and running with legacy drivers - no effect
disabling embedded Ethernet adapter - no effect
unplugging the second display (an HDTV) - no effect
tried to get a manual crash dump - not possible as when the issue happens the HTPC is freezed
Those tries took very long to be made, because every time i have to wait all day long for the issue to happen: it NEVER takes place if i wake up the HTPC after a few seconds sleep, seems like it needs at least a few hours of S3 state to take place.
Now, many particulars of the issue seem to lead to a compatibility problem between PSU and motherboard: i read about other users experiencing similar problems using high-end PSUs (min load related?), problems they solved by finding older or cheaper PSUs compatible with their MB (that's a blind try thing, luck was needed)... but in all cases PSU functioning was not bad, so no RMA was possible. Anyway, it is obvious that changing MB solved the issue as well... so Corsair support states it is not a PSU issue but a MB related one.
This seems to be a frequent problem for intel z68 based MBs, but i suspect my 990fxa MB can show the same compatibility issue with Corsair AX PSU, assuming some power related modification has happened in the last month in PSU or MB circuitry.
So i would like to know if someone else is/is not experiencing the same issue using same MB and PSU; more, i would like to know what 80+ PSU is SURELY working flawlessly with my MB, in case i should have to solve the issue by replacing the Corsair PSU (that is manufactured by Seasonic); finally, i would like to ask MSI technicians to verify the issue and possibly working around it with a BIOS update (maybe raising resume initial load, if PSU min load is to blame).
Thanks in advance.

Even with AMD power reduction, consumption while on is nearly ten times than in standby... it happens me to leave my PC in S3 for 3/4 days, so power consumption would be too much (i write from Italy and here AC current is much expensive!).
Anyway, i took a more accurate look around about PSU/MB incompatibility and i'm now sure enough that this is the problem. It seems certain MBs in power saving modes (like S3) require a too low power from PSU, so that PSU min load is not achieved, that makes it malfunction. This happens to new, energy efficient PSUs, that eliminate minimum load resistors to achieve maximum efficiency...
Look at this: http://www.silentpcreview.com/forums/viewtopic.php?t=58802.
So this issues happen because MB is too efficient (it requires too low power from PSU) and PSU is too efficient itself (it eliminates power used to remain above min load in power saving). Is this true? It seems ridicolous to me!!!!!!! To save a couple of watts we are forced to leave PC on so wasting dozens of watts? Are PC engineers really dummies?
BUT it looks like this can easily be solved by a BIOS adjustment, isn't it?

Under Windows 7 - Fingerprint Reader Ignored After Standby Resume

I thought this was perhaps a platform-specific issue. But both on my ThinkPad T61 running Windows 7 Ultimate 32-bit and my new ThinkPad T510 running Windows 7 Enterprise 64-bit, whenever I resume from standby, any finger swipe against the fingerprint reader is ignored.
Note - I am not using the rather large Lenovo fingerprint driver package because I don't want the bloat. Just want a very basic, Ctrl+Alt+Delete password prompt replacement.
Does the "Registry patch to change IDLE IRP timing by Fingerprint reader driver for Windows Vista" need to be installed under Windows 7 (http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-67245)?

i didn't know the lenovo fingerprint driver package was more than just a very basic, Ctrl+Alt+Delete password prompt replacement? (at least not that i noticed)
T400s - 2815RW1 + Win7 Ultimate
Don't pm me for help! That's what the forum is for. Also, Google's nicer than me. Ask him.

Satellite 1410 standby/resume issue

Similar Messages

Maybe you are looking for