Satellite 1800-100: video-out does not work

He,
I just installed windows XP on my old Satellite 1800-100, but now my video-out does not work anymore. So I just downloaded the latest driver, but there's no way I can get it installed. According to Windows the new driver isn't newer, so it won't let me update it. And when i try to unistall the display driver, I have to reboot before it takes effect, and wile rebooting it automaticly installs the standard driver again.
Can anybody help me?
Greets,
Daan

Hi
Do you mean TV- out port or monitor port? As far as I know this unit is preinstalled with WXP Home and all drivers can be also used for WXP Pro.
Did you preinstall your own OS (non recovery image)?

Similar Messages

Tecra S1 video out does not work

Hi,
I tried to connect my TS1 via cinch to a beamer. Unfortunately because of other reasons I can not use VGA.
However I do not get any signal at all. I tried nearly everything. I installed Windows XP with Toshiba Recovery CDs again, but it does not work either.
Is there anyone knowing what to do?
Best wishes,
Markus924

hi Markus924,
do you have a picture on the internal lcd?
via chinch to a beamer - this wont work...
you get a pal/ntsc signal from this connector.. i am not sure if your beamer can handle this sort of signal...
take a vga cable to try *and* install the "fn-f5" tool from toshiba to switch the picure to external display.

Tecra M4: TV s-video out does not work with Vista

I have windows vista ultimate on Tecra m4.
I tried to get tv out through s-video but nothing happened.
I tried fn+f5 but it shows only Lcd choice with no other choices.
While it works good with windows xp tablet edition I installed the newest driver offered by toshiba but nothing happened.
The same problem is still here; no tv out.
Can any one help me

Hi
As far as I know the Vista drivers are not available for the Tecra M4 at this time.
I have checked the Vista driver download site and the M4 is not listed.
I think you have to wait for compatible drivers
If you install the graphic driver, you should check the Nvidia display settings. There you could choose between the TV, analogue display and digital flat display.
There choose TV and configure it via device settings

Installed Premiere Pro CS4 but video display does not work?

I just got my copy of CS$. After installing Premiere I found two things that seem very wrong:
1) video display does not work, not even the little playback viewer next to improted film clips located on the project / sequence window. Audio works fine.
2) the UI is way too slow for my big beefy system.
My pc is a dual boot Vista-32 and XP system with 4GB of memory installed and nvidia geforce 280 graphics board with plenty of GPU power. The CS4 is installed on the Vista-32 partition. My windows XP partition on the same PC with Premiere CS2 works great and real fast.
Any ideas how to solve this CS4 install issue?
Ron

I would like to thank Dan, Hunt, and Haram:
The problem is now very clear to me. The problem only shows up with video footage imported into PP CS4 encoded with "MS Video 1" codec. So this seems to be a bug. The codec is very clearly called out and supported within various menues but video with this codec just will not play in any monitor or preview window. In addition the entire product looks horrible with respect to performance while PP CS4 trys its best to play the video. Audio will start playing after about 30 seconds. And once in awhile part of video shows up at the wrong magnification before blanking out again.
My suggestion to the Adobe team: fix the bug and add some sample footage to the next release so new installations can test their systems with known footage.
My PC is brand new with the following "beefy" components:
Motherboard
nForce 790i SLI FTW
Features:
3x PCI Express x16 graphics support
PCI Express 2.0
NVIDIA SLI-Ready (requires multiple NVIDIA GeForce GPUs)
DDR3-2000 SLI-Ready memory w/ ERP 2.0 (requires select third party system memory)
Overclocking tools
NVIDIA MediaSheild w/ 9 SATA 3 Gb/sec ports
ESA Certified
NVIDIA DualNet and FirstPacket Ethernet technology
Registered
CPU: Intel Core 2 Quad Q9550
S-Spec: SLAWQ
Ver: E36105-001
Product Code: BX80569Q9550
Made in Malaysia
Pack Date: 09/04/08
Features:
Freq.: 2.83 GHz
L2 Cache: 12 MHz Cache
FSB: 1333 MHz (MT/s)
Core: 45nm
Code named: Yorkfield
Power:95W
Socket: LGA775
Cooling: Liquid Cooled
NVIDIAGeForce GTX 280 SC graphics card
Features:
1 GB of onboard memory
Full Microsoft DirectX 10
NVIDIA 2-way and 3-way SLI Ready
NVIDIA PureVideo HD technology
NVIDIA PhysX Ready
NVIDI CUDA technology
PCI Express 2.0 support
Dual-link HDCP
OpenGL 2.1 Capaple
Output: DVI (2 dual-link), HDTV
Western Digital
2 WD VelociRaptor 300 GB SATA Hard Drives configured as Raid 0
Features:
10,000 RPM, 3 Gb/sec transfer rate
RAM Memory , Corsair 4 GB (2 x 2 GB) 1333 MHz DDR3
p/n: TW3X4G1333C9DHX G
product: CM3X2048-1333C9DHX
Features:
XMS3 DHX Dual-Path 'heat xchange'
2048 x 2 MB
1333 MHz
Latency 9-9-9-24-2T
1.6V ver3.2

DVI video out suddenly not working.

That's basically it. I have a 23-inch Cinema HD Display at home and at the the office. Suddenly the video out is not working with either of them. The displays control panel lists the external display, so the system is detecting the connected display.
There is nothing wrong with the displays. I connected an old PowerBook and they light up fine. With my MBP, the power light lights, but nothing is displayed on the Screen.

there's a somewhat similar thread "external monitor stopped working" with no answers
my 17" Studio display works as 2nd mon on other computers
my dvi out does work with a vga monitor and adapter, of course :))
i'm using the dvi to adc adapter -- could this be involved somehow?
my laptop display goes blue when i plug in the external monitor as it should, but the 2nd monitor never wakes up, turns on, etc.

Macbook Pro 2011 DVI HDMI out does not work with TV when the power cable is connected

My Macbook Pro (Early 2011) DVI HDMI out does not work with TV when the power cable is connected. If get the blue screen and then can use the macbook but nothing is displayed on the TV. If i go into display I can see that there are two screens but nothing displayed on the TV. If i take the power cable out at this point the TV shows the second desktop as expected. If i then reconnect the cable, the screen flickers, as though it is being affected by the power cable, and the screen goes blank on the TV. Only if i remove the DVI cable do i get the blue screen again. If i remove the power cable and reconnect it will do it every single time, so i cannot see it being a TV issue or a minor glitch.
I have had this working previously but at the minute it seems to not be playing ball....any thoughts
Thanks
Dan

BUMP
Any ideas?

Video Filter does not work.

Hello.
I have been using Final Cut Pro 4 for a while and it worked fine before. But recently, any function of Video Filter does not work. I apply them to the clip, but the image does not show any changes on Canvas.
Is the software's problem?
Thanks in advance.
Ying

For a reason unknown to me, FCP's preference files (there's 3 of them) will sometimes become corrupted and need to be trashed. Usually the symptoms are things just not working as they did earlier, or weird issues like the 3 Way Color Corrector looks different than before ... stuff like that.
FCP Rescue is a freeware app (yes, you'll need to download it) that will create a backup set of preferences, thereby retaining all of your settings. Then when (not IF, but when) FCP's preferences become corrupted, you can run FCP Rescue to replace the bad set with a fresh new set.
Otherwise you can delete the files yourself (make sure FCP isn't open at the time) and the next time you launch FCP, it will revert back to the factory settings.
-DH

Upgraded to iOS5.1 and now video out is not working. How do I fix this?

After upgrade to iOS 5.1 the video out is not working! Anyone have this problem? Is there a fix for this?

OK so I went to the Apple Store and they said my cable was a third party cable. We tried an apple cable and it worked! So Apple changed the pin out configuration on the OS 5.1 upgrade so only Apple cables will work! So I had to shell out another $40.00 to get that cable!

Audio in video messages does not work

When I record a video message for someone, the audio does not work properly. It either doesn't work at all (silence is recorded), or cuts out after a 1-2 seconds. The problem seems to be confined to the MP4 video/audio encoder used by Skype for video messages.
My webcam (Logitech HD615) works properly when used for Skype calls (including the built in microphone), and when used in other applications. With other applications, I can also record videos and the audio is captured and encoded correctly. Although the problem does not seem to be the webcam, I have re-installled the webcam drivers and I have tried changing USB ports for the webcam.
I have re-installed the latest version of Skype and verified that Windows has the latest updates (I'm using Windows 7). I have tried re-booting a number of times when debugging this issue.
I have looked at the mp4 file that's created in the temp folder when Skype records the message - the audio is missing/broken regardless of what player I use. This, and the fact that the webcam works makes me believe that the problem is in the Skype use of the audio/video encoder, or the encoder itself.
Any ideas on how to solve this problem?
Thanks,
K.
Solved!
Go to Solution.

When you change the USB ports, make sure not to use USB 3.0 ports. I had a very similar issue with Logitech c920 webcam. Changing the port to USB 2.0 has solved the issue.
http://community.skype.com/t5/Windows-desktop-client/No-sound-on-video-messaging-playback/m-p/274382...

My video zoom does not work on my iphone or ipad after IOS 7.0.2 update.

After updating iPad and iPhone 4S to IOS7.0.2 the video zoom function does not work. I have also lost the function to zoom on video playback.

Is somebody from Apple monitoring these forums? I do have the same problem, i just recently noticed that the zoom in my video camera is no longer available since I upgraded my 4S iPhone to the newest version.

Google talk video plugin does not work any more with Firefox 4. When clicking on the video chat icon, I am repeatedly asked to install the plugin, and it never works.

Google talk audio/video plugin used to work fine on Firefox 3, but does not work anymore on Firefox 4. Every time I click on the video chat icon on google talk, I am asked to install the plugin, even if I have already installed it before. The plugin works properly on the latest version of IE on the same PC.
Thanks for your help. I do not want to switch to Chrome or Opera, but if this bug is not fixed, I will have to.

Not sure if installing IE 9 did it or not but I now see the camera in IE, FF and Chrome. Could be Facebook fixed the problem also.
Thanks for the reply.
George

2nd video card does not work

I have a spare Mac Pro here so I decided to remove the video card and put it in the one I'm using. Both machines were purchased in '09 and use the same video card (ATI Radeon HD 2600). The two monitors I have hooked into the original video card work fine but the monitors I hooked into the newly placed video card are not working. Under the About This Mac specs >> PCI cards it shows up and says driver is installed. Is there anything special you need to do to get a second video card to work?
Thanks.

I tried the SMC reset. I removed the card and reseated it. I'm seating it in slot 2 because that's the only other one that is x16. The other slots 3-4 are x4. Still nothing is showing up. When I go to System Preferences >> Displays >> Detect Dispalys nothing happens. The two displays plugged into the original video card work fine but the newly installed on does not show up. Here is what the Mac Info is detecting. Maybe this makes sense to someone. Not sure what MSI is referring to and the second video card is reading as "display" instead of "ATI Radeon HD 2600". Link speed on the second card is half that of the original.
About This Mac >> More Info >> PCI Cards >> Slot-1
ATI Radeon HD 2600:
Name:    ATY,Lamna
Type:    Display Controller
Driver Installed:    Yes
MSI:    Yes
Bus:    PCI
Slot:    Slot-1
Vendor ID:    0x1002
Device ID:    0x9588
Subsystem Vendor ID:    0x106b
Subsystem ID:    0x00a6
Revision ID:    0x0000
Link Width:    x16
Link Speed:    5.0 GT/s
About This Mac >> More Info >> PCI Cards >> Slot-2
display:
Type:    VGA-Compatible Controller
Driver Installed:    Yes
MSI:    No
Bus:    PCI
Slot:    Slot-2
Vendor ID:    0x10de
Device ID:    0x0393
Subsystem Vendor ID:    0x0000
Subsystem ID:    0x0400
Revision ID:    0x00a1
Link Width:    x16
Link Speed:    2.5 GT/s

Satellite A660-11M - Power Saver does not work

I have a Satellite A660-11M and I work on Windows 7 Ultimate
The problem is that I have download all drivers and updates but the toshiba power saver does not work its installed with no error and TPSLaunch (green icon) does not open when I click on it and no icon I found in the control panel for the program afterIi install all the Value Added Package!

Hi buddy,
Wait a moment, please.
Im a little bit confused about your posting First you write about Power Saver and then about green icon Which one you mean exactly and whats the problem?
If you mean Eco mode you have to install Eco Utility from official Toshiba website.

Satellite C50-A0121: My ribbon does not work in libraries

Hi there
Please can you try assist me.....
In Libraries my ribbon does not work, the layout wont allow me to make changes, the right click does not work when i want to select any of the options
I know this might sound blonde for a gal to be asking but PLEASE help
thanks
Yve

Thank you for the reply
It is a Toshiba Satellite C50 - A0121 (C1005 4096)
Ive attached two pictures
1) the properties do not come up when i right click on any file
2) the format on the ribbon does not work, where you change the way you look at a folder
Originally Posted by Juan28
Sorry but your message and issue is not understandable enough.
Could you please post the notebook model and the system you are using?
Please explain exactly (very detailed) whats wrong with your notebook!

Satellite C660-11W - Num pad does not work

Hi!
I have a Toshiba Satellite C660-11W, who I bought 10 months ago. Since October, the num pad of my laptop does not work, but when I push the button "Num Lock", it makes a sound like I had activated the sticky keys.
How do I solve this problem?

Hi
Sounds a little bit like keyboard malfunction.
I think the service technician should need to initialize the Numpad function by Test & Diagnostic software and should replace the keyboard if the test would fail.

Satellite 1800-100: video-out does not work

Similar Messages

Maybe you are looking for