Satellite 1801 - Play movie file lagging with Windows XP

This laptop been format and re-install OS (Window Xp), the movie player are power DVD 5 player, real one player and jet audio are having the same problem.
Did any body can advice that I having playing movie file (such as .VOB, rmvb,..), lagging problem?
Even though total 512 MB was add into system.

Hi
If your play the movies from a disk (DVD) then you should check the settings in deivce manager.
Access the device manger and check
IDE ATA/ATAPI controllers -> Primary IDE Channel -> Properties -> Advanced settings
Here the transfer mode for Device 0 and Device 1 should be set to DMA if available.
It this is not the case then I recommend removing the Primary IDE Channel from the device list and to reboot the notebook.
The Windows should recognize this device again and then check again the settings mentioned above.

Similar Messages

How to play MOV files inside Windows Media Center Edition

I've installed QT Pro, but am not able to play MOV files inside Windows Media Center Edition (MCE). Under "My Videos" from the MCE main interface, I can see the files, but once selected, error message indicates unknown/unplayable file type.
How do I get my MOV files to play inside Windows MCE??
Marc

Quote from: cosmosk on 05-April-05, 22:29:47
I don't use MSI's MC application so I can't directly answer your question.
However both Win DVD 6 and PowerDVD6 play them just fine by launching the ts.ifo file.
Yes, I know that, but that means that I should use at least two applications. I need only one front end to launch all my media files, inluding ripped DVD files, not as separate VOBs but as whole movies decribed in IFO files.
Kiero

Quicktime not playing .mov files

i have a problem with quicktime. it doesn't play .mov files. if i try to play .mov files that are embedded in a .pdf file, a window opens but stays blank, although the progress bar moves. if i try to open the files in quicktime, there's no window, just the progress bar that moves. i run the latest version. i've already tried reinstalling - didn't help, uninstalling completely and installing - didn't help.
help?
many thanks!
diana

Quicktime>Quicktime Player Preferences>Advanced
Click on the MIME Settings button.
In the next window that opens up make sure that Streaming-Streaming movies is enabled (checked).
While you’re at it make sure all the boxes are enabled by clicking on the corresponding triangles so that they are pointed down.
This will show the “hidden” boxes especially the *QuickTime Movie* box. This box will enable you to play .mov files.
Click the OK button.

Cannot play .mov Files....

I am not able to play .mov files in my JFrame Window....
The Visual Content shows onli a pink screen and following exception...
The mov file which i tried to play is a standard file and plays well with quicktime player... Its not working with my code alone... I ve posted my code also... Can anyone look at this issue and guide me????
*--------------------Configuration: <Default>--------------------*
*# An unexpected error has been detected by Java Runtime Environment:*
*# EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x7c911c48, pid=1864, tid=996*
*# Java VM: Java HotSpot(TM) Client VM (11.2-b01 mixed mode, sharing windows-x86)*
*# Problematic frame:*
*# C [ntdll.dll+0x11c48]*
*# An error report file with more information is saved as:*
*# D:\project\New Folder\hs_err_pid1864.log*
*# If you would like to submit a bug report, please visit:*
*#   http://java.sun.com/webapps/bugreport/crash.jsp*
*# The crash happened outside the Java Virtual Machine in native code.*
*# See problematic frame for where to report the bug.*
*import javax.media.*;*
*import java.awt.BorderLayout;*
*import java.awt.Component;*
*import javax.swing.*;*
*public class summar extends javax.swing.JFrame {*
    *public summar() {*
        *initComponents();*
    *private void initComponents() {*
        *trailer1 = new javax.swing.JPanel();*
*          trailer1.setLayout(new BoxLayout(trailer1,BoxLayout.Y_AXIS));*
*          trailer1.setVisible(true);*
        *setDefaultCloseOperation(javax.swing.WindowConstants.DISPOSE_ON_CLOSE);*
        *getContentPane().setLayout(null);*
        *trailer1.setBorder(javax.swing.BorderFactory.createLineBorder(new java.awt.Color(0, 0, 0)));*
*Player player=null;*
                *try{player=Manager.createRealizedPlayer(new MediaLocator("file:\\c:\\common\\trailer.mov"));*
                *player.setMediaTime(new Time(30.0));*
                *trailer1.add(player.getVisualComponent());*
*          Control controls[]=player.getControls();*
*          CachingControl cc=null;*
                *for(int i=0;i<controls.length;i++)*
*               if(controls[i] instanceof CachingControl)*
*                    cc=(CachingControl) controls;*
*                    trailer1.add(cc.getProgressBarComponent());     *
*                    System.out.println("Found CachingControl");*
*          if(player.getControlPanelComponent()==null)*
*               System.out.println("Null");*
*          else*
*               trailer1.add(player.getControlPanelComponent());*
catch(Exception e1){}
getContentPane().add(trailer1);
trailer1.setBounds(250, 70, 320, 220);
pack();
*public static void main(String args[]) {*
summar s=new summar();
s.setBounds(0,0,960,660);
s.setVisible(true);
private javax.swing.JPanel trailer1;

When I 1st used QT after upgrading to ML, I received a message saying that a codec was missing, and that accordingly QT could not play the files. Just now, after tinkering with VSL in vain, I re-launched QT, and opened what had been a '.mov'-file, only to find that it is now an '.mpg'-file. How that transformation occurred, I do not know, but the result is that QTwill play the file perfectly well.
I am back with QT, and many thanks to you all that have tried to help.

HT3775 Hi...I have the OS X v10.6.8 but my QuickTime is not playing .mov files. How can I fix this?

Hi...I have the OS X v10.6.8 but my QuickTime is not playing .mov files. How can I fix this?

Hi...I have the OS X v10.6.8 but my QuickTime is not playing .mov files. How can I fix this?
Depends of the specific kind of file you are trying to play. MOV refers to the file container. Any data compatible with the system used to create the file can be placed in an MOV file. If you don't have the same codecs available on your computer to play back the file or if your version of the QT player does not expect expect the encoded data to be in an MOV file container, then it cannot/will not play the file. Use the Finder Info window, media player Inspector/Information window, or a dedicated utility to determine what compression formats were used to create the MOV file and then install the required codec(s) if available.

How do i play .mov files

Hi
I suspect that this has been asked before, but how do I now play .mov files. I created some movies a few years ago for teaching purposes and need to use them again. However, neither iMovie nor Quicktime seem to recognise/support the .mov format.
Any help would be much appreciated
Don

Are you saying that there are settings that I can adjust to let current versions of Quicktime/iMovie/iTunes play the files, or do I need to use another programme to convert the files into a current form that will be recognisable to current standards?
I am saying that we have no idea what codec components were used to create the original files. (I.e., the MOV file container is like a bottle, can, cup, glass, or other container that can be filled with any liquid, solid, or gas that can be fit into it.) For instance, if were created as Windows Media Video files and copied to an MOV file container, then you would need Flip4Mac components installed on your system. If they were created using DivX, XviD, 4IVX or similar codecs, then you would need to update those codecs or remove them and install the Perian codec package. MOV files containing muxed MPEG-2 video would require installation if the Apple QT MPEG-2 Playback component. FLV content in an MOV file container could be played with the Perian package installed. If the files were created using one of FCP "Pro" components, then those same codecs must be installed on the platform on which you wish to play the files now. And so on down the line of "legacy" and third-party codec compression formats which may or may not be spported by the latest versions of QT which tend to concentrate on newer technologies that support HD compression formats.
What I am saying is that without knowing what codec components were used to create the original file, it is impossible to tell whether you simply need to install currently available components that will allow you to play the files in the QT X, QT 7, use a third-party player like VLC for playback, or whether you would have to re-compress the files that target codecs no longer available for current hardware/software system configurations. Further, I am saying that the first step in solving a playback problem is to clearly define the specific problem in terms of the file container, compression format(s) involved, data characteristics as specified by Inspector, Media, Finder, or third-party utility windows or providing a sample file for analysis if you cannot determine this information on your own.

Quicktime will not play .mov files since Lion installation

When using Quicktime 10.6, I am receiving the error message "...file could not be opened. A required codec isn't available." when attempting to open .mov files. Prior to installing OS X Lion, there were no issues with playing .mov files.

I'm having the same problem. Using a clean install of Mac OS X (10.7) Lion and QuickTime 10.1.
If I go to finder:
I can click on Icon's Play arrow and the Movie will play in the icon.
I can click on the file icon and press the spacebar and the file will play in QuickLook.
If I doubleclick on the icon to open the file in QuickTime, I get the "...file could not be opened. A required codec isn't available." message.
If I right click on the icon and click open with... QuickTime, I get the "...file could not be opened. A required codec isn't available." message.
MBP, Mac OS X (10.7)

Can't play .mov file!!

hello,
i'm having some trouble playing .mov-files.. I can watch trailers on apple.com but when I have a mov-file on the pc, it opens with a flashy green screen and pressing play will only give my a static (mostly green) and no noise.. this goes also for iTunes, movies there i cannot open but i can watch them on my ipod..
anybody any ideas?
thanks

What codec is this HD file? If they shot and captured in the Sony XDCAM EX format, FCP 5.1.4 won't be able to see that. The XDCAM EX support comes only with FCP 6.0.3.
Shane

Bridge doesn't play movie files

I have Bridge CS5 set to play movie files when it encounters them but for some reason it has decided to stop doing so.

Thanks for the link but I have a slightly different problem.
I have now discovered that Bridge plays most .mov files but not those in a particular folder. Has anybody any idea why?
I can however play these particular files with Nero. It's just that one would prefer to have Bridge do it when one is working in Bridge. But, it has to be said (and I'm talking about hi def movie files here) Nero plays them smoothly without a hitch whereas Bridge playback is jerky. Why? Is Nero using a different codec and if so can one get Bridge to use the same one?

I updated my computer and now I can't play mov files from anywhere

I updated my computer and now I can't play mov files from anywhere - won't play in FCP 7, Quicktime. Not sure what updates they were specifically since i hit the "update All" button without going over each one. Please help!! operating on 10.6.8 with FCP7

Just take a look at the last few days posts here and you'll see many people with the same problem and some possible solutions.
But you should never do any software updates unless you have a bootable backup of your startup drive. FCP7 is no longer being supported by apple and updating anything is fraught with dangers.

Problems playing .mov files in QuickTime 7.2.0

Hey everyone!
I have a problem with my QuickTimePlayer.exe application. It will play all other movies just fine, except for .mov files. It will open them and play .mov files, the sound will be fine, but the video is extremely choppy.
I FINALLY got to play .mov files by uninstalling QuickTime 7.2.0 and installing the Vista Codec Package 4.4.8, which contains QuickTime Alternative. The only problem is that it doesn't come with QuickTimePlayer.exe, which is what I want my .mov files to open with.
After hours of installing, uninstalling, and re-installing codecs, I discovered that it wasn't a codec problem at all. It was the QuickTimePlayer.exe application that was the issue.
But what's weird is that the exact same version of QuickTime on another computer will run .mov files *WITH QUICKTIMEPLAYER.EXE!!* So there's something going on with some settings in my computer.
I can't seem to figure this out. Does anyone else know what the problem could be? Thanks in advance!
Brent

I've discovered the problem!! It was the latest release of the NVIDIA nForce drivers that were the issue.
For as to WHY this specifically affected the playback of .mov files, I can imagine how. It's weird how the one thing you least expect to be the problem actually IS the problem.
Anybody have any idea how it affects it?

Can't play .mov files in Xine

Hi
I am pretty new to Arch but it is great so far. I am running vanilla KDE4 with Xine as the Phonon backend. One problem I'm having is that I can't play .mov files. Other stuff like .wmv and .avi play ok. I also have the codecs package installed.
For example, no luck with this file
http://media.crossfit.com/cf-video/Cros … llUps1.mov
Thanks!

Welcome to the forums DeKay.
This isn't going to help, but I can confirm this using Xine 1.2 (dev) and almost a pure FFmpeg backend. ffplay and Mplayer can both play this file properly, so it's without a doubt a Xine problem. I ran a gdb trace on it and didn't really get anything to report upstream either.
Last edited by skottish (2008-11-15 23:11:08)

No video but sound when playing .mov files

I'm trying to play .mov files on my computer and I get sound but no video. I've installed the latest verson of QT and no help.
The computer is an older MBP.
randalhillphoto

I should explain better. The mov files are exports from a 2-year-old MBP using FCP and exporting the files as self-contained movies. They were exported to use as an archive and saved on DVDs. Now I'm working on a 4 year-old MBP with FCE and trying to open the files with quicktime after downloading them from the DVD archives. I get the sound but no video. Please help me resolve this.

Play mov files on iPad?

iPads supposedly play mov files. However iTunes won't let them copy. How can I get mov files to an iPad and then playthem?

The iPad 2 supports:
Video formats supported: H.264 video up to 1080p, 30 frames per second, High Profile level 4.1 with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats;
MPEG‑4 video up to 2.5 Mbps, 640 by 480 pixels, 30 frames per second, Simple Profile with AAC-LC audio up to 160 Kbps per channel, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats;
Motion JPEG (M-JPEG) up to 35 Mbps, 1280 by 720 pixels, 30 frames per second, audio in ulaw, PCM stereo audio in .avi file format
You can convert the format to an iPad compatible one use a converter computr program like the free HandBrake. You can also purchase an app that will play .mov format videos. You will use FileSharing to transfer them to the iPad. Here is one free app.
https://itunes.apple.com/us/app/id502405034?mt=8
BTW this is the iPod touch forum

Automator only playing .mov files

I am working with Automator trying to create a simple video scheduling app. I created a workflow that ...
1. Gets a specific movie
2. Plays the movie full screen.
Everything is tied into iCal and seems to work well except that I can only play .mov files. mp4 files and .avi files will play in Quicktime Player but will not when called through this workscript/app.
Any thoughts?

I'm not sure if this is even the right forum so I apologize if it's not. Just trying to get an aswer about playing my .mov files.
I have the new Ipad and I have been recording videos. I'm looking to get these videos online on my website.
What is the best way to put this on my website so there is a video player and all.
Right now I just added the videos online but there are no play, pause and rewind options and its just 1 big page of video.
Your question is somewhat ambiguous. How you place the files on your web site will depend on how you are creating/managing the web site and how you plan for viewers to watch them. This can range from simply loading the files to an online server and accessing the content directly by its URL in a compatible browser app like Safari or dedicated players like QT 7, QT X, MPEG Streamclip, VLC, or devices like the iPad, iPhone, etc. to embedding/calling specialized "viwers/players" from within the programmed web page.
Not being a web site programmer myself, I normally just transfer the content to my system and either copy the files directly to my server or use iWeb to publish the files to my server for more generic web site viewing.

Satellite 1801 - Play movie file lagging with Windows XP

Similar Messages

Maybe you are looking for