Satellite 2430-201: TV tuner receive only audio signal

Satellite 2430-201
Grapgic card Geforce4 420Go NVIDIA
Installed TV tuner: AVERTV USB2.0
The TV tuner receives tv chanells but without Grapgic only audio.
What could be the cause of this problem?
Where can I find softwere or update for display ? the one I have is display-xp-613103230.zip

Hi
In my opinion its not the problem of the graphic driver. But if you want you can try to update this. You can find the newest driver on the Toshiba website.
http://eu.computers.toshiba-europe.com/
Furthermore I recommend checking the settings of the AVerTV software (NTSC, PAL)
Bye

Similar Messages

Satellite 2430 wirles-lan card is not supported by windows xp

i have a MPC13A-20/R internal w-lan card in my satellite 2430-201 , and have downloaded and installed the updated driver (wlesslan-xp-7620390) from toshiba.
The hardware is recognized, but will not configure.
windows xp gives me the standard failer article 871122 to read, which is hopelessly uninformative.
I have service pack 2 installed as well as all other available updates, and my BIOS version is V1.3
what do ya think?

Hi
MPC13A-20/R wireless card is produced by Agere Systems. Like you can see updated driver that you downloaded is just for wireless card produced by Toshiba. On Toshiba download site there is under company registered Toshiba and version is 7.62.0.390.
In your case you need Agere driver for your wireless card. Please visit producer site and I am sure that there you will find right driver for MPC13A-20/R wireless card.
Good luck!

Why when i try to download a audio cd to i tunes it only downloads half of the cd

why when i try to down load a audio cd to i tunes it only downloads half of the cd

Hi Jolly3jo,
If you are having issues connecting to or downloading from the iTunes Store/App Store on your iPad, you may find the following article helpful:
Apple Support: Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
Regards,
- Brenden

Satellite 2450-201: USB Controller only 1.1 instead of 2.0

I have formated the hard drive on my Satellite 2450-201 and loaded Widows XP SP2. I loaded all the drivers from the utilities disk and everything is working fine except the USB ports are only running at 1.1 instead of 2. There is a yellow exclamation mark in device manager on USB controller. I have searched for a driver from Toshiba downloads but there is nothing available.
Can anyone suggest a soloution to this problem.
John

Hi John
As far as I know there is no driver for USB controller. When you install chipset driver all USB ports should be recognized properly. Exclamation Mark in device manager is an indication that the device is not configured correctly. Try to remove the controller and restart the unit. After that check the status in device manager again.
Is some external device connected to the unit by USB ports?

HT202157 Rented movie on ipad and only audio would come through on my Apple TV. What is wrong?

I Rented a movie on my ipad and tried AirPlay on Apple TV but only audio came through how can I watch video too?

Previews and trailers do not contain 5.1 audio.
If you have recently moved your setup, you may have inadvertently changed some of the settings on your receiver. It certainly sounds as though it is unable to play the 5.1 audio from the Apple TV.

Satellite Pro S500 - Mini displayport also carry audio?

Does the mini displayport on the Satellite Pro S500 also carry audio?
Chris

I agree with user above. Only one port can transfer video and audio signal at the same time and it is HDMI port.
If your notebook hast this port use it for usage with TV. Using this port you will have best audio and video quality on the TV.
If you need some more info please let us know for which purposes you need this audio signal transfer.

No Video, only Audio when building a DVD in Encore CS6

Hi everyone!
First post here, and I apologize if this has been somewhat covered in other posts, I couldn't seem to find any similar issues in this matter, and I pray someone here can help.
I'm new to DVD authoring, and just started using Adobe Encore CS6 over the summer. I shot a dance recital, and after following some tutorials, made an awesome DVD that was very well received.
However, my last two DVDs have not come out working properly. I imported .m2v files from HC Encoder (DVD Compliant, max 7500kbps for safety) into Adobe Encore CS6, where the .m2v files say "Don't Transcode." They play just fine in the timelines in Encore.
When I build the DVD to either a folder, image, or disc, only audio plays for the video portions of the DVD. The only way to get the video to play is if I run the DVD through VLC. I tested in Windows Media Center (on Windows 8) as well as my PlayStaton 4, and the black picture with audio persists for each video element of the DVD.
Between making the DVD of the dance recital and the DVD today, I have gone through at least two complete system restores, if this is something that could possibly have made things go awry. If it helps to know, I'm running Windows 8.1 Pro.
Thanks in advance for any advice!

Oops, sorry!
I imported an *.m2v file along with a *.wav file, both the exact same durations and lined up correctly in the timeline. In the project panel, for the *.m2v it says "Don't Transcode" for Status and "Don't Transcode" for Settings; for the *.wav it says, "Untranscoded" for Status and "Automatic" for settings.
That's all that Encore's telling me about the files.
Side note, interestingly enough, I went back and re-exported the DVD of the Dance Recital that I had mentioned earlier, and it plays just fine. (I'm trying to compare the two projects as best I can) It seems as if the *.m2v file that I made in HCEncoder for the recital plays just fine in Windows Media Player, however my most recent ones do not. But they still play in Encore. Needless to say, I'm baffled.

Satellite 2430-402, Display Driver Problem

I have a Satellite 2450-201. Very often when the system comes back from Hibernate the system will not re-boot, it gets stuck after the opening logo. I have to shut it off and then then got to safe mode, and then restart. I get a message that the system has recovered from a device failure and it identifies the Nvidia Display Driver as the culprit. I have re-loaded the latest Driver from Toshiba, but if I try ANY update from Microsoft the Display goes crazy, and I have to go throught the re-boot and safe mode thing again. Any ideas on what the problem may be?

Good evening ! I had this problem with my Satellite 2430-402. Ive updated the Bios and all was fine.
Did you checked your Bios Version at first ?

Cant send data to nike cause i tunes received unexpected response from server

my workout can not be sent to nike+ because i tunes received an unexpected response from server

Hi,
From
this documentation, though SharePoint 2013 supports several commonly used web browsers including Apple Safari (latest released version), it is not guarantee
that SharePoint 2013 can run perfectly on all these browsers, “certain web browsers could cause some SharePoint 2013 functionality to be downgraded, limited, or available only through alternative steps”.
According to the code provided, it seems more relate to ASP.NET, therefore, a suggestion is that you can open a thread in ASP.NET forum, communities there will be more familiar
with this issue:
http://forums.asp.net/
Thanks
Patrick Liang
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Patrick Liang
TechNet Community Support

Satellite 2430 XP Boot Problem

Windows XP won't load on my Satellite 2430-402 laptop saying that the C:\Windows\System32\config\system file is missing or corrupted and to try running the repair option.
I have 2 Toshiba Recovery CD's from which I have managed to run the DOS-based recovery programme which has 2 options:
1. Full Restore, which I don't want to do
2. Selective Restore, which I do want to do, but have no instructions
I do not appear to have an XP CD from which I could run Microsoft's recovery application.
Can anyone provide me with the steps to undertake a selective recovery from Toshiba's (actually Symantec's) dos-based recovery CD?
Thanks

Hi,
In this case I am always merciless. Back-up data and make new installation. Only then I am 100% sure that everything works properly. :)
Anyway, if you want to make new installation with Recovery CD there are two possibilities:
- Standard mode (whole partition will be deleted and OS new installed)
- Expert mode (you can chose on what partition you want to install OS)
Very important is that there is no Repair option. This option you can find on Microsoft WindowsXP CD.
There are few possibilities to try to repair your OS. You can try to replace defective system file. Copy system files from another PC and replace it. I must also tell you that there is no 100% guarantee that it will be successful.
You can also try to provide Microsoft WindowsXP CD (full version). Maybe you can have some success with repair option.
Next possibility is to use Windows Recovery Console. I assume you have access to a second computer. Go here for instructions which may help you.
http://support.microsoft.com/default.aspx?scid=kb;en-us;314058
This article describes the functionality and limitations of the Windows Recovery Console. If your Microsoft Windows XP-based computer does not start correctly or if it does not start at all, you can use the Windows Recovery Console to help you recover your system software.
A few days ago here was interesting posting about this theme. You can find it on:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=1823
Good luck!

Satellite 2450-201: Cannot format 4GB card in SD card slot

Hello,
I´m a Satellite 2450-201 owner and I have a big problem.
I just bought a 4GB SD memory card and nice, it fits on the side slot on my notebook.
It's the first time using the memory card, so a needs-to-format window appears when I try to access.
The Window has the right information : 3.78Gb, Fat32, ...
I Click "OK" and the Windows (XP SP2) informs : cannot complete format (here is portuguese, so it's translated to english)
If the right size is informed , 3.78Gb, why the Windows cannot format ?
My notebook is spyware and virus free (just 23 tasks running and under control), I Have SP2, Bios 1.50 (newer), My SD controller drivers is up-to-date (the last and the only one was released in 2003).
Also tried third party "Panasonic SDFormatter 2.0". It's reporting the unit (hardware) or the mem stick SD is not compatible with the program. And the same effect happens : the Sd unit lost the nice icon and I need to remove/insert the SD to see the same story again.
Help me please, friends.

Hi
Its very strange that youre possible to see the SD card after plug-in. some people has suggested that this SD card slot supports only 256MB, 512MB cards and additionally with no MMC support.
I dont know if you have Toshiba SD card format utility installed on the laptop but on many Tosh notebooks such utility is preinstalled and could be used for the card formatting.
According to some posting in this forum the format utility of Portg M400 could handle the 2GB SD cards but not sure about 4GB.
If possible you could try to install this utility on your notebook but you know you have not big chances that this will work.
I think in such case only a external SD card reader will help you.

Satellite 2430-402 has a life of its own

i had my satellite 2430-402 for just over 2 years and it has been absolutely fine but recently i noticed a problem which is getting worse every day. every few minutes the arrow mode icon lights green (without me touching the Fn key) and i lose control of the computer...strange writing appears..wizards open and close infront of me and im totally powerless as the keyboard stops working during this event...it continues for less than a minute and then every thing goes back to normal for a minute or 2 then the same thing happens again....
I'am about to start typing a thesis for my work and there is no way i can do it if this problem persists...by the way although it happen at any time it can be made worse if i try to type any thing,,even a password to log into a website...i had to use a friends computer to send this sos message...can any one help please...thanx
[Edited by: admin on 30-Jul-05 10:10]

There might be different reasons for that... SOFTWARE or HARDWARE !!!
First you will have to check if this happens only when you are running windows.
SOFTWARE:
If yes,
(1) a malicious program (trojan, keylogger etc) might be installed on your laptop, or
(2) a faulty driver might be the reason. Have you recently attached a usb mouse or keyboard to your computer? This might have installed a wrong or incompatible driver.
Start your computer and keep it in the PRE-BOOT stage (enter the BIOS-SETUP and wait to see if this will occure there again).
HARDWARE:
If yes, I assume that the contacts of your keyboard film are dirty. You will have to remove the keyboard, open the film-lock and clean the contacts with alcohol or a contact spray. If you are not familiar with this procedure, please consult the Technical support.

Satellite 2430-301: Cannot use 2200BG WLan card because switch is off

Hi there,
I have a Satellite 2430-301 which was not deliverd with any WLAN capabilities. But I discovered, that there is a MiniPCI slot in the laptop.
So I bought an Intel PRO/Wireless 2200BG MiniPCI card. After I attached the card into the laptop, it was detected by windows as a new network device. I downloaded and installed the Windows XP drivers (because I have Windows XP installed on the Laptop) from Intel's homepage (9.0.4.17). The installation worked perfecly.
Now I tried to connect to a wireless network, but the Intel software said, that the card is 'off'. So I switched the drop down menu to 'on', which resulted in an german error: "Die Intel(R) PRO/Wireless-Netzwerkverbindung ist noch deaktiviert. Aktivieren Sie sie ber Ihren Hardware-Schalter." (which means something like "The Intel(R) PRO/Wireless network connection is deactivated. Activate it with your hardware switch.").
Although the switch already was in position 'on', I switched it several times - nothing important happend. The LED light near the switch doesn't light in either position.
Are there any incompatibility issues between "Toshiba Satellite 2430-301" and "Intel PRO/Wireless 2200BG"?
Did I do something wrong?
Is this damn hardware switch broken?
Any suggestions?
I would really be happy, if someone could help me :)
Thanks in advance,
thuriel

I now pressed Fn+F8 several times. The laptop did not react.
In the property box in the advanced tab in the 2200BG properties there is only:
Ad Hoc Channel
Mixed mode protection
Power Management
Preamble Mode
Roaming Aggressiveness
Throughput Enhancement
Transmit Power
Wireless Mode
...so there is no "radion on/off".
The LED light remains off, no matter what I do.

No video in Viewer/Canvas, only audio

I use Final Cut Pro X since Day One and I survived bugs and endless beachballs on my 2011 17' Macbook Pro.
A week ago FCPX stopped playing any video in viewer/canvas while scrubbing. Only audio is audible. Impossible previewing a single clip or playing the timeline. The beachball is immediate and the program hangs and need forced exit. This happens whatever the video source is: only audio plays. Same reinstalling from scratch 10.0.4. Trashing preferences and using quickfix from Digitalrebellion didin't help.
A momentary solution has been creating a new administrator user and working from there, with many limitation and commodities I have "on the other side".
I can't identify anything particular that might have caused this! Quicktime runs fine and so do Final Cut Pro 7, iMovie and all the video compartement.
I searchead the web but nobody seems to have follen in this situation.

Have the same problem. Did you ever find answer?

My MacBook Pro with Lion 10.7.2, only audio on the headset, and speaker mute. With Windows, the audio works in speaker and headphone jack. What is the problem? What's the solution?

My MacBook Pro with Lion 10.7.2, only audio on the headset, and speaker mute. With Windows, the audio works in speaker and headphone jack. What is the problem? What's the solution?

There is probably a red light on inside your headphone port, indicating that the analog/digital switch in there is stuck in the digital position. Insert a headphone plug and wigle it around, especially in the horizontal plane, as you insert and remove it several times. This will usually unstick the switch and restore normal operation. If it doesn't, the machine will need to be repaired.
This has been a fairly common problem, but in most cases it is easily cured as described above.

Satellite 2430-201: TV tuner receive only audio signal

Similar Messages

Maybe you are looking for