Satellite 4030cds beeps on startup (POST codes)

Hi does anyone have a list of POST codes...I think I have
1 long 4 short followed by 1 long 3 short.
Does that make sese.
Thanks.
John.

Hello John
Unfortunately there is no public document about that. If you are not able to start the unit or even enter BIOS settings there is some hardware malfunction. The unit should be checked by technicians who can read the codes and locate the a defective hardware component.
Bye

Similar Messages

2 short 1 long beep on startup, posting

Hi, i'm using the H61M-E33 motherboard with the i5 2500 processor, 2 x 2GB DDR3 Corsair XMS3 1333mhz sticks of RAM.
i've tried reseating the RAM and each of the RAM sticks by themselves and also tried a friends RAM which also didn't work every time i get the same beep codes on startup.
it is giving us a warning saying the monitor signal is out of range when we startup though, we're connecting VGA-VGA as we don't currently have a functional adapter.
Any Ideas?
Edit: we've put the graphics card in and now we've got windows installing, still not sure what the beeps mean though.
Edit: we had a dodgy DVI adapter with a bent pin which was preventing the signal to the monitor, the beeps we still don't know what they are but the system seems to be running fine, perhaps MSI just decided to put this sound on there to confuse people.

Quote from: Stu on 12-June-11, 19:33:17
I really don't know why so many people make such a big issue over the USB beeps. Unless you're shutting down and restarting your PC every two minutes, they're hardly noticeable.
No big problem at all so long as you know what going on and if like myself and others new to MSI boards as well as putting a pc together I think you tend to be a little over sensitive to all the bleeps.
As for disconnecting the speaker, same answer as above. But it''s there for a reason and I think most people push the button and wait for the post beep almost crack a little smile and get on with what your doing. Sad? possibly but hey!

T500 Beeping on Startup

One week ago, my computer (Lenovo ThinkPad T500) has started beeping upon startup (one long, two short) and will not allow the system to start. I have to shut down and restart a considerable amount of times before the display finally shows up. The odd thing is that it has informed me that this indicates a video problem, and yet I have run diagnostics and the such, and there is nothing wrong. Furthermore, my computer runs perfectly, if not even better than before the beeps started.
This problem is starting to get annoying and I'm afraid that I might irreversibly damage my computer if I keep trying to start it up when it is beeping. How can I fix this?
Thanks for all of your help!
Solved!
Go to Solution.

katrimc, welcome to the forum
according to the Hardware Maintainance Manual, (pdf p. 52), the beep code means that you possibly have a problem with either your System Board, Display or Memory. I suggest removing and reseating your memory, (pdf p. 78 or look here), and if the problem persists to run memtest86 to check your memory. Let it make at least 3 full passes.
If your memory passes and the symptoms still persist you should call support.
Let the forum know how you get on.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

G4 beeps on startup

I got a new HD and new 512MB stick of ram put into my G4. It seemed fine after the HD was installed but a few days later when I bought some second hand ram and slapped it in I got a faint beep on startup. I tried every combination of the ram, but couldn't get rid of the beep untill I unplugged the new HD. So I took it in to the Mac store where I got the HD installed and we couldn't hear the beep!! Took it home and it beeps again, but only when the new HD is plugged in. One strange thing is that the total ram only shows up as 1.19 when it should add up to 1216 MBs; that is two 512's, one 128, and one 64mb stick.
Any ideas?

Hi, Mike -
Welcome to Apple's Discussions.
One strange thing is that the total ram only shows up as 1.19 when it should add up to 1216 MBs; that is two 512's, one 128, and one 64mb stick.
1216MB is correct, and 1.19GB is correct. RAM math is a bit odd because it is base2. One GB = 1024MB, not 1000MB. So, 1216MB divided by 1024MB/GB yields 1.19GB.
Is it possible the drive itself is beeping? Some few have been known to do that, but when that happens it usually presages a drive failure - not something expected with a new drive.
Is the drive jumpered correctly? If your Mac is older than a G4 (MDD) model, you should not use Cable Select jumper settings.
There are some beeps at startup which can indicate RAM issues -
http://docs.info.apple.com/article.html?artnum=58442
However, those will replace the normal startup chime. That is, if you hear the normal startup chime and then the beeps, it's not a RAM issue.
At least one person posted a similar issue a few years ago. Careful listening finally traced it to the user's UPS - it was alerting that it was running on battery.

MSI 990FXA-GD80 updated POST code "99"

I started my computer up last night after 3 months of using it and now it is posting a 99 code when I start the computer. I can't get to bios or boot. Keyboards will not work (both PS2 and USB). BIOS was completely up to date for nearly 3 weeks.
This morning, to no avail, I tried a new power supply.
At this point I have tried all of the following:
-Disconnecting HHD (SATA and POWER)
-Disconnecting Opitical Drive (SATA and POWER)
-DISCONNECTING ALL F-PANEL (PWR SW, PWR LED, HDD LED, RESET SW)
-Disconnecting the USB and HD AUDIO
-Disconnecting ALL fans.
-Mounting and remounting the motherboard
-Mounting and remounting the CPU
-Attempting to use a new video card
-Attempting to use a new power supply
-Placing MOBO on a different surface
-Reseting the CMOS via the on board button and removing the battery
-Using only 1 stick of ram to boot
-New PSU
Basically I am booting the PC with the power button on the MOBO and the only things connected are the 8 pin MOBO power, the CPU, 1 stick of ram, and 1 of 2 different working video cards.
After doing all of those things, the MOBO stills post code "99" on the screen and on the MOBO itself. Additionally, keyboard does not work. Furthermore, I cannot access my BIOS or boot screen.
The original video card and the replacement video card both work on another PC therefore they are not the problem.
Thus, at this point, I have narrowed the malfunction down to either the following two components:
-Motherboard
-CPU (which I doubt, but do not have a AM3+ mobo on hand) or another AM3/AM3+ processor
Any suggestions or advice are more than welcome and needed.
I am considering RMAing the motherboard...

Quote from: xmad on 19-July-12, 03:06:34
Hopefully the cpu isn't the problem, wish there was a way for you to test it out. A computer shop perhaps?
Just to be clear, you removed the mobo from the case with just a cpu, cooler, 1 stick ram & psu and don't hear the no vga beep?
I see you already tried a new psu.
Hope you get it right soon, good luck I think you are right it's either the cpu or mobo.
Yes. The GPU is working fine I tested it in another computer. I installed another working GPU, it did the same "99" post.
Unfortuneately, there are 2 PC shops close by. 1 of them is a "mom and pop" type place that really doesn't get too deep in to technical aspects and doesn't care much for AMD products. The second is a shop that only carries very low end products as well as some i3 type proccessors and mobos.
Thus, since none of the computer stores give a flip about AMD, I am out of luck in that aspect. I have quite a few AM3 boards laying around, but that does me no good with this Zambezi.
On a side note, I decided to remove the processor. The processor and the heatsink became merged together. What I mean when I say they became merged is that the thermal paste become basically a superglue between the heatsink and the processor (the FX-4170 naturally runs hot, thus, AMD has included an upgraded heatsink in it with better thermal paste). Anyhow, in order to remove the thing I could only get the mounting lever about a little over half way up. Therefore, on the back row, the pins bent a little (I would say there were making somewhere between a 80-85 degree angle orthogonal to the board). I took a credit card and a screw driver and straightend the pins, stuck it back in, still posted the same thing.
Last but not least, I read over the mobo specifications and realized that it was backwards compatible. The MSI 990FXA-GD80 AM3+ AMD 990FX SATA 6Gb/s USB 3.0 ATX AMD Motherboard supports the following CPU types/sockets:
Quote
FX / Phenom II / Athlon II / Sempron 100 Series
I realized I had a (working) AMD CPU HDZ955FBGMBOX Phenom II X4 955 Black Edition 3.2GHz AM3 125W Retail, thus, I mounted it on the MOBO... SAME CODE POSTED...
It must be the motherboard.

1955-S805 POST codes

My S805 started hanging last night. I have to hold the power button down to reset the machine. When I reboot, it beeps once and then immediately shuts itself off. Trying again, it gives me 3 beeps, 3 beeps, one beep. I was able to boot this morning for about 5 minutes and then the same thing happened along with the same "beep" sequence.
Does anyone have a list of POST codes?
Thanks,
Scott

Bios Beep Codes

3 short beeps on Startup

I had to do a System Recovery and ever since then, I get 3 short beeps on startup. It does it 4 times... Any ideas?

Hi,
Could be BIOS related..
The link below will tell you what the Beep codes indicate..Follow the instructions as per the the beep codes
Beep and LED code descriptions
BIOS Beep Codes
Note:
If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
Although I am an HP employee, I am speaking for myself and not for HP.
**Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

KN8 Diamond plus 3 beeps at startup problem

When I connect a Lide 500f scanner I get an extra beep at startup connect a skype phone and I get another extra beep so alltogether PC now beeps 3 times at startup, there are Know problems running PC. Is this a known problem that a new bios ( using 1.20 now) might sort and could it cause a problem long term.

Gigabyte Triton case Gz-xx1ca-sns
LG DVD writer GSA 4167B
LG DVD writer GSA 4163B
2 GB crucial memory DDR PC3200 (2 sticks)
AMD 3500+ (2.2) socket 939 CPU with heat sink / fan
XFX PCI Express Geforce 6600GT 256 VGA card
Zalman VGA cooler ZM80D-HP
MSI K8N Diamond Plus motherboard
Maxtor Sata 250GB Hard drive
Maxtor Ide 160GB Hard drive
Tagan TG480 –U22 power supply
beeps are the ami bios beep codes and come from case speaker 3 beeps should indicate a memory problem as thats not the case I would guess at a bios update curing the problem just find it strange problem is uknown. Bios has been cleared and is 1.20

Post Codes for P965 Platnum

Im about to fire up (no pune I hope) my P965 Platnum. Where are the post codes in the manual? I have not seen them any where. Thanks

Bios Beep Codes

Post Code 9A Error, 990FXA-GD80, Bios bug

After Bios B.40 i got same strange bug, sometimes when i load a oc profile my pc get stuck at 9A error and the only thing that i can do to recovery is use ctrl+home to recovery it, clear cmos is unless.
After a lot of tests to try understand what was happening i got the answer.
My CPU is a X3 710 (waiting for bulldozers) so i always use the unlock cpu core feature. I used this x3 with unlocked core for 2 years without any problem, so the locked core is good.
If i load a oc profile with unlock cpu core feature enabled from a already unlocked stage, everyting is ok, but if my bios seting "unlock cpu core" is disabled and i load a oc profile with it enabled my pc do 6 beeps, restart and get stuck at 9A post code.
I have sure that in Bios B.30 this wasnt happening.
MB: MSI 990FXA-GD80 (MS-7640)
BIOS: V11.5 (B.50)
CPU: Phenom X3 710
RAM: 2x2GB Corsair XMS3
VGA: ATI Radeon HD 4890 (RV790) 1GB
DISK1: 120 GB OCZ-VERTEX3 SATAIII SSD
DISK2: 3TB Hitachi HDS5C3030ALA630 SATAIII HDD
Optical Drive: SAMSUNG TSSTcorp CDDVDW SH-222AB SATA
Power Supply: GenieX 800 Watts
OS: WIndows 7 Ultimate Sp1

Guy, did u see me asking anything about overclock?
I was talking about a bios BUG that can damage the mainboard, and a lot of ppl cant recovery their bios like i did.
I posted to help ppl with same issue and alert others to avoid it.
I informed MSI about it using the right channel.
Ty for help me bump this topic.
Quote from: Fredrik on 26-September-11, 06:52:23
Hello!
Overclocking questions go somewhere else.
If you don't absolutely need to update BIOS to solve a problem, resist the temptation.
And if you do... Go back to the version that made you smile!
We ask people to state the max ampères the PSU can do. There is a list on the PSU box.

790FX-GD70 - FREEZES ON POST CODE "08"

Hi
I have just made a new build on a new 790FX-GD70 winki board - on initial start up it's freezing on the POST code "08". Nothing is showing up on the screen at all. Apprently this means:
08
Initializes the CPU. The BAT test is being done on KBC. Program the keyboard controller command byte is being done after Auto detection of KB/MS using AMI KB-5.
(according to http://www.ami.com/support/doc/AMIBIOS8_Checkpoint_and_Beep_Code_List_PUB.pdf)
The trouble is i just don't know what that means I should do - without anything on screen to go by!
My system is
MBD: 790FX-GD70
CPU: PHENOM II X3 720 2.8GHZ BLACK SKT AM3 7.5MB 95W PIB
RAM: 2gb from: Corsair Dominator XMS3 4GB (2x2GB) DDR3 1600C9D Twin3X (TW3X4G1600C9D)
GRAPHICS CARD: SAPPHIRE ATI RADEON HD 4770 512MB GDDR5 TV-OUT/DUAL DVI HDMI PCI-EXPRESS - RETAIL
PSU: 650W BeQuiet Dark Power Pro Modular PSU BN073
Any help or ideas would be really great as i'm totally at a loss.....!?

Quote from: Henry on 07-September-09, 18:24:45
... What PSU model and amps for +12V rail(s)...

"Post code Incorrect" error while Posting Invoice !!

Hi,
While posting an invoice for a PO , using transaction MIRO , I'm getting the error message as " Post code incorrect - please check document header field".
Any help on this is highly appreciated.
Thanks,
Arvind

If a postal code is correct or not is defined in rules set in county definition. Here the length and certain other criterias can be checked. SAP programs the logic based, you choice is to do the checks or not
So somebody might have changed the customizing after the vendor was created.
I guess you get the same error if you go in cahnge mode into the vendor master and change any field and try to save.

Post code in delivery address when creating PO

Hi friends,
when creating PO, the post code field under delivery address tab is a required field. while some of our delivery address do not has post code. it seems a mandatory filed.
How could I change it to a optional field.
Thanks,
Linda

Ask your ABAPer to assist you on this.
Path to Screen Variant
Choose Basis Components - Application Personalization - Tailoring of Application Transactions - Configure Transaction-Related Display Values for Fields
Screen variants allow you to simplify screen editing by:
Inserting default values in fields
Hiding and changing the ready for input status of fields
Hiding and changing the attributes of table control columns
A screen variant contains field values and attribute for exactly one screen. A screen variant may be assigned to multiple transaction variants, however. Screen variants are always cross-client; they may, however, be assigned to a client-specific transaction. They can also be called at runtime by a program. The different possibilities for calling screen variants guarantee great flexibility of use. A specific namespace has been designated for screen variants and they are automatically attached to the Change and Transport System.
Check following lInk:
http://wiki.sdn.sap.com/wiki/display/Snippets/TransactionVariant-AStepbyStepGuidefor+Creation
Thanks & Regards
JP

HPE-170f suddenly starts giving POST codes at power on.

HPE-170f AY604AA#ABA Windows 7 Home Premium 64-bit
HPE-170f suddenly starts giving POST codes at power on.
Have Logitech solar blue tooth keyboard and Logitech bluetooth trackball.
POST code is short, short, long ... if anyone remembers what that means.
Have been randomly successful at continuing boot after connecting USB keyboard and disconnecting all other USB devices and then holding ESC while turning on. Not 100%, but works mostly.
I have no idea if anything USB is actually causing.
After boot starts and WIN is loaded, everything else seems normal.
Any suggestions?
Thanks, dtipton

Hi,
Short, short long typically is a video problem.
What hardware changes have you made to the PC?
Unplug your PC and open it up. Remove the video card and use a can of compressed to clean out teh dust from inside the card. Now put everything back together and give it a go.
Remove as many USB devices as possible and then monitor the situation.
It's possible that you have a flaky video card or power supply.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Z87 Mpower (post-code A0 or AD or AO??)

Good day!
Tell me, please, which means a combination of A0 (or AO or AD?) mainboard post-code screen?
OS (Win 7 64 ult) booting correctly.
It's okay, or worry? Google did not help to find a definitive answer.
Thank you!

Many thanks for the quick reply!
I duplicated my question to MSI support team.
Quote their response:
"Regarding your concern, the post code means the MB is detecting the devices installed, please don't worry about it. Thanks!
Thanks for your cooperation in advance!
Best Regards,
MSI Technical Support Team"

Satellite 4030cds beeps on startup (POST codes)

Similar Messages

Maybe you are looking for