Satellite 4080 xcdt, small Picture after changing resolution to 800x600

Hi.
After changing the Res. to 800x600 or lower (while playing an older DOS-Game), the screen is reduced to postcard-format.
Has Anyone an idea to solve this problem,(other display-driver or s.th.)?
Greetings, R.

Hi Ralf,
I believe there is a setting in your BIOS to force the screen image to stretch to fit the available space.
regards,

Similar Messages

  • Need keyboard for Satellite 4080 XCDT

    Hi,
    on my Keyboard the left buttens (TAB, q,a,y,CAPS) are defect. But If I press "<shift>-a" a "L" appears on the screen, so I think the buttons are not broken, maybe a chip in the keyboard or notebook.
    I want to buy a new keyboard, where can I get one cheap?
    Which keyboards(from which Toshiba-modells) fit in my Notebook too? ( for ebay search ;-) )
    Satellite 4080 XCDT
    thanks in advance
    Biber

    Hy Biber,
    part number for your KB is P000256660
    BR,
    Stiv

  • Satellite Pro L40 wont boot after changing BIOS settings

    Alright changed a few settings in the bios last night and now when I boot I get a black screen lights flash and that hard drive light comes on but nothing on screen.
    There was no password on bios,... how would I reset BIOS to normal?
    I put a windows disk on I can hear the disk spinning but nothing on the screen
    (I think I have come to the right place on the forum)
    Its a Toshiba Satellite Pro L40 model psl4be.
    Thanks

    >There was no password on bios,... how would I reset BIOS to normal?
    You can set the BIOS to default ONLY inside the BIOS so you have to access the BIOS pressing F2 or at the beginning of the booting order
    But I doubt that this problem is related to the BIOS.
    Maybe its just a simple bad luck that this issue happened just exactly after changing something in BIOS.
    Try to connect an external monitor and check if you can see something on 2nd display.

  • Monitor went black after changing resolution

    I changed my mac mini resolution to something higher. The screen went black and now it never shows anything on it anymore. I turned off the mac and the monitor but still the same problem when I turn the mac back on. How can I get to see the screen again?

    Hello Bill,
    Welcome again to the Apple Forums.
    Most likely you have picked a screen resolution and/or screen signal frequency that is not compatible to drive your monitor.
    You have a couple options available to you.
    Option 1.
    Restart your mini computer and turn off the monitor.
    Let the mini computer start up completely.
    The mini will detect no monitor is detected and default to a lower resolution and frequency setting.
    Turn on your monitor after the mini has completed its start up.
    Option 2.
    Restart you mini computer and leave the monitor turned on.
    Hold down the shift key on the keyboard after you hear the start up tone.
    The mini will start up in Safe Boot mode and switch to a lower resolution and frequency setting.
    Cheers
    Jan J.

  • IMac 27'' little bit blurry after changing resolution.

    Hello. I recently bought a 27'' iMac 2013. As the screen is too big I changed the resolution from 2560x1440 to 2048x1152. But it look a little bit blurry now. 2560x1440 is really good but texts and other thing hard to see. Is that normal? I think Apple should do something about it. My eyes are really fine but even for me it was hard to see texts. They are too small.

    in windows one can change dpi of text and the likes in the video settings this partly does what you want
    I don't believe it's possible with osx at least not unless one use a thirdparty program
    I say partly because while it makes text bigger and easier to read some applications looks a bit odd compared with normal
    in osx are some tools in the acccability in system preferences where you get a loop but I never really played around with them'
    also cehck out this
    http://www.macworld.com/article/2026699/stop-squinting-make-text-bigger-in-os-x. html
    more
    https://www.google.dk/search?q=make+bigger+text+in+osx&oq=make+bigger+text+in+os x&aqs=chrome..69i57j0l5.3889j0j7&sourceid=chrome&espv=210&es_sm=93&ie=UTF-8

  • No satellite signal on certain channels after changing boxes - getting nowhere with sky help

    So I got a new sky box from sky and have been getting the No Satellite signal message on certain channels (i.e. Sky1 HD, Sky Atlantic and Sky Sports) since I changed the boxes. I have tried all the suggestions in the online help as well as through the call centre  personnel who just repeat the same thing over and over. Can anyone please assist? To get things started: 1.  Yes, the viewing card was paired.2. The input signals show OK for any channel that is possible to view. When you look at the input signal details for a non-working channel then Input 1 shows as NOT LOCKED and input 2 as OK.3. Communal dish and no problems in other flats.  

    It might be local interference.  You'll have to switch off any wireless equipment in the room,  and especially a wireless router,  cordless phone base station and anything else that radiates signals. You should also unbundle ( if applicable ) your dish Input cables from anything else behind the box, in particular power leads. If you're using the white,  pre-moulded cables from the likes of Homebase,  B&Q etc,  it might be an idea to replace them with good quality,  double-screened cabling such as WF100 which you can buy online. Are you able to borrow someone else's HD box to test in your flat,  or are you able to check out your own box on a non-communal setup?

  • No video signal after changing resolution...

    Hi guys...
    I have had this issue in the past.
    I have an ATI Radeon 9000 on a G4 Quicksilver. I have had it hooked up, for the last few years, to my Toshiba Regza 42" LCD utilizing a DVI to HDMI connector.
    Recently, my wife and I have decided to sell the Quicksilver so we flattened the hard drives and did a clean install of Leopard.
    From there, I upgraded Leopard from 10.5 to 10.5.8 and then went to change the resolution to 800 x 600 as I had in the past so I could test out VLC's speed. The signal went out...and never came back.
    Not panicking (I had a prior issue on this board and it was fixed), I restarted in Safe Mode. However, when I went to Safe Mode, the resolution I wanted was already chosen and when I clicked on it again and restarted OUT of Safe Mode, I'm STILL getting "No Video Signal" on the Regza.
    I've also noticed that while 800 x 600 works (in Safe Mode), you cannot restart into that resolution AND it's surrounded by black bars rather than filling the whole screen like it used to. I don't get this.
    I've been told that I may have to erase the entire set of drives again and install only up to 10.5.6 or lower as this is an Apple resolution issue.
    I REALLY don't wanna do this.
    Is there a way to fix this issue?
    Thanks!

    1920 x 1080 and 800 x 600 so far. I haven't had the guts to try anything else. I lost Safe Mode by going to 640 x 480 once as well as 1024 x 768.
    The issue is that the Regza can be set to the first to in Safe Mode but will not reboot to these resolutions when booting normally.

  • Satellite M50-156: How can I change resolution for my external monitor?

    Hi,
    I bought an exernal monitor for my laptop M50-156 which has a resolution of 1920x1080.
    But the problem is that such a resolution is not available in the display settings of my computer!
    I tried to update the graphic card and chipset, but the max resolution I have is 1280x1024!
    So my external monitor cannot display properly :( Did anybody have the same problem?
    Please help.. Thanks.
    Beb

    > But the problem is that such a resolution is not available in the display settings of my computer!
    The resolution is not available and this says everything!!! Its not possible to choose this and you will have to use another resolution!
    There are two reasons why your favorite external resolution is not available:
    1) the graphic card chip does not support this
    2) or the graphic card driver does not contain this resolution.
    In your user manual you can find all supported and available external resolution
    But I assume the 1920x1080 is not supported

  • My Pogo game does not fit the game window even after changing resolution pixel only on Firefox.

    In Pogo games my game is too large for the game window. I tried various pixel resolutions and game is still too large. Extending the window will not help.

    What site?

  • MBP Display changes resolution to 800x600 after sleep

    Weird situation... I usually just shut the cover of my MBP forcing sleep. If, for some reason my cursor is at the upper left corner, and I open the lid, the screen will go black for about 1 second, and the display has changed to 800x600. All I haver to do is reset the display in Preferences and all is ok again, until the next time. This does NOT happen every time I put the NBP to sleep - very arbitrary. I only have one hot corner assigned for Expose (lower right).
    I'm current on OS and firmware.
    Any ideas ???

    Situation does not present itself anymore. Issue closed.

  • T43p-blue screen after changing display settings

    Display turned blue after changing resolution obviously to some wrong settings, how to revert the process when cannot see anything but the start up sequence?

    go into the safe mode and change the resolution, or at least reinstall the driver. Press F8 during initial startup of the laptop. 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • HP Photosmart 6510 series network printer will not print black after changing cartrage

    HP Photosmart 6510 series network printer will not print anything that is black or has black in the picture after changing cartridge, all other colors are working properly after changing. Does not look like any damage to the cartridge or the insert where you plug in the ink. The well where the ink pad and the cartridge meet is damp with black ink. So not sure what is going on

    Hello dinger57 and welcome to the HP forums!
    I understand since changing the black cartridge the black ink has not been printing. I'm sorry to hear this, but I will definitely do my best to lend a hand
    I will suggest that you start with following through this Printer Does Not Print Black Ink or Color Ink, or Prints Blank Pages document. If the issue persists after that can you please let me know what country you're in and whether the printer is in or out of warranty? Thanks! Please feel free to private message me the country information.
    Hope to hear from you soon!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • Why can't I enlarge safari bar and bookmarks bar so the print is larger.  I can only do this if I change resolution on display.  I do not want to make my 27" smaller.  Any comments?

    After just installing Mountain Lion on mid 2011 iMac 27" I find it does not allow increasing size of font for Safari bar and Bookmarks bar.  The print is so small it is difficult to see.  I can change resolution of screen but the the size of the screen becomes smaller.  Not what I had in mind when I bought this iMac.  Is there any fix out there and is Apple working on this problem?  Any comments would be appreciated.  Thanks.

    Safari – Enlarge browsers toolbar text
    Firefox

  • How do i print out my picture after scanning it. it comes out way to small

    after scanning my picture i print it out and it comes out way to small

    VisionAiry wrote:
    If you print the scans and they come out too small, it may be that you have a setting off when you scan it in.  To resolve this problem completely, you could simply make a copy instead.  But in order to assist you with this, I will need to know a lot more information.
    1.  What kind of printer do you have (Officejet 8600, Photosmart C6380, etc)?
    2.  What kind of computer do you have (Windows 7, Windows 8, Mac OS 10.8, etc)?
    3.  What software/program are you using to scan (HP Scan, HP Solution Center, Paint, etc)?
    4.  What program are you using to print the scans (Windows Picture Viewer, Photoshop, etc)?
    5.  What is the file type of the scan (.pdf or .tiff)?
    Make sure your scan size is equivelant to the page you are scanning, resolution is set to at least 600 dpi, the item type is set appropriately such as to document since photo will make the image smaller, and go to advanced settings to check file size is not set to "Smallest."
    I hope that helps.   If not, I will need to you to answer the questions above please or I will not be able to help you.  However, I have provided all the necessary information above regarding an HP printer on a Windows PC using the HP Scan.  
    Let me know if I can be of any more assistance. I'm happy to help!
     I have the same problem. I have a HP Photosmart 7525 printer and work with Windows 7. I just want to copy a photo and it keeps coming out much smaller. I just put the photo on the scanner plate in the corner, choose the copy icon, and out comes a small picture in the corner of my photo paper,.There must be a setting somewhere but I can't find it. Can anyone help me?

  • In putting together a book I can move photos onto a page and enlarge the picture but is there a way to reduce the picture size? some cases I want a smaller picture and if I change the size of the picture box I only get a portion of the image. I wnt to red

    picture size...in putting together a book I can move photos onto a page and enlarge the picture but is there a way to reduce the picture size? some cases I want a smaller picture and if I change the size of the picture box I only get a portion of the image. I want to reduce the image to fit the size of the box.

    If you right click on the image on the page in the context menu select photo box alignment and then select one of scale to fit {centered, Left-aligned, Right-aligned}
    That should do what you are loking for.

Maybe you are looking for