Satellite A100-510 PSAA2E cannot boot up - nothing on the screen
Hello,
I've had this Satellite A100-510 (PSAA2E) since May 2006.
2 weeks ago, when I tried to turn it on the fans started spinning and the leds lighted up and after around 2 seconds it reboots without ever showing anything on the screen.
There are no beeps or anything also.
I've tried pretty much everything: removing the hard drive, wireless card, screen, dvd drive, switching the RAM between slots...
It didn't make any difference though.
So I'm guessing either it is a memory problem or the motherboard is dead, what do you think?
> So I'm guessing either it is a memory problem or the motherboard is dead, what do you think?
Yes, the mentioned parts could cause such issue
But this would be the worst case and you would need to contact the Toshiba ASP for further details
Before you would get in contact with ASP, I recommend trying this:
- remove the battery, disconnect the AC adaptor.
- Wait 30-60min
- Connect both parts and try to power up the notebook
Maybe if this short workaround would help you
Similar Messages
-
I don't know BIOS password for Satellite A100-528 PSAA2E
hi..i have a problem...
i have a laptop Toshiba SATELLITE A100-528 PSAA2E-01H00WGE....
the problem is that i downloaded toshiba HW setup and i accidentaly set a password..
.not a user password....it's propably supervisor password or bios password...
.the thing is that i don't know what the password is...i boot up my pc and it don't let me get in windows if i don't type the password.....is there any way to remove the password ??
it does not let me either boot from a cd or usb....i press F12 in order to choose to boot from cd or usb but it's still asks for the unknown password....is there any solution ??
please answer it's critical !!
thank you very much...>the problem is that i downloaded toshiba HW setup and i accidentaly set a password..
>.not a user password....it's propably supervisor password or bios password...
Thats weird because the BIOS or Supervisor password can be reset only by an authorized service provider.
The BIOS password is a high security option which cannot be reset easily.
So ONLY ASP can remove a UNKNOWN password. -
I have an iPhone 3gs... The only thing that will come up on my screen is the apple logo with the little loading circle thingy... I have plugged it into iTunes and it updated and synced with no problems but still nothing on the screen...
PLEASE HELP!!!!iPhones that use the ARM chips (2g + 3g) are VERY slow to boot. Sometimes in excess of 1 minute 30 seconds (personal experiece). Assuming the device is not JB or has anything wanted on it, such as photos, do a DFU Restore. To cut it short, it basically forces itunes to give it the latest ios (4.something I think). Otherwise, personally I would wait
-
my iphone 5 screen has gone black in the middle of updating a app. i have tried to back it up using itunes and restore it however it will not restore my phone as i have got the app find my iphone switched on. i cannot turn it off as the screen is black. can anyone help me please??
christobell86 wrote:
... it will not restore my phone as i have got the app find my iphone switched on.
You can access iCloud.com on a computer to turn it off.
http://support.apple.com/kb/PH2702 -
My ipod nano is dead,nothing on the screen? it is charged
I was listening my ipod and suddenly it was dead, nothing on the screen,I tried to reset it and nothing. Did someone know how can I make it work again?
anafromfrisco wrote:
I was listening my ipod and suddenly it was dead, nothing on the screen,I tried to reset it and nothing. Did someone know how can I make it work again?
Recharging -
I cannot open my phone as the screen will not work. I have made an appointment with a technician tomorrow but is there anyway of backing my phone up to Icloud so that I do not lose any of photos etc etc?
PLug it into yrou computer to sync/back it up.
Is it set to back up to iCloud now?
Or do you have wifi backup enabled in iTunes?
Plug it in while on wifi and it will automatically back up. -
An Apple genius pressed a few buttons before booting my computer then the screen changed to a database of parts of my computer and their status. How do i do this?
Julianwerules wrote:
then the screen changed to a database of parts of my computer and their status.
can you elaborate more? I'm not familiar with a database of parts..or I'm having a major brain ****. -
I know my network connection is fine and I've checked all the cable connections and my television is set to the correct input, but even though the remote beeps when I hit the button, I see nothing on the screen. The troubleshooting section in the setup guide says to make sure that Apple Tv is connected to my network by choosing Settings>General>Network. How do I do this? What do I need to do to get everything back? I've been using the Apple tv for a while now, and suddenly it's doing this.
This is the iPod touch forum. I requested your posted be moved to the Apple TV forum
Using Apple TV -
I cannot start my iPad. The screen is black or shows a persistent Apple logo.
try a hard reset, and try to put the device in recovery mode and restore
-
I came home and attempted to power on my iPad2. I can see the backlight but nothing on the screen. When I try to reset by pushing the off button and the power button at the same time I can sometimes see the characters briefly but the screen has lines. Can someone tell me if there is anything else I can do before a trip to the repair shop?
WillIf the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here. -
My emails have frozen. Open ended up an email last night and now nothing on the screen will move.
Quit the mail app completely and reboot the iPad. Go to the home screen first by tapping the home button. Double tap the home button and the recents tray will appear with all of your recent apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up. -
I cannot access my device. The screen is blank however it has power. The phone will ring but since the screen is blank I cannot answer. It seems to be dead but has power?
When restoring to factory defaults/new iPod fails to resolve a problem that indicates a hardware problem an an appointent at the Genus Bar of an Apple store is in order.
Check your warranty coverage here:
Apple - Support - Check Your Service and Support Coverage -
I went to charge my ipod touch lastnight and it would not charge. There was nothing on the screen no life in it. Well today i plugged into my laptop and itunes came up saying it is in recovery mode. Im trying to restore it but nothings happening on my ipod got the apple sign on the screen and the bar going across but its emtyand theres nothing loading, itunes also says waiting for ipod. Someone please help cant live without my ipod,
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Ok so my new iPod Classic is repeatedly restarting itself and I see nothing on the screen But the Apple logo and I canny do anything to stop it can anybody help me
Try the DFU Restore method shown in Corrupt iPod classic.
tt2 -
My iPhone 4s screen went black. I can hear the phone receiving messages though. I tried to restore through itunes. I failed because "find my iPhone" app is on, I cannot switch it on since the screen is black and I can't see
Instead of trying to restore through iTunes, use the Find My iPhone to your advantage.
Either go to www.icloud.com and perform a remote wipe of the device via FMiP, or download the FMiP app to another iOS device and do it from there.
A remote wipe will also restore the device back to factory settings.
Maybe you are looking for
-
Problems in creating new final cut title in motion 5.0.5, not read from fcx
i am trying to create title in motion 5.0.5, but after saved them in new category i open them in final cut x (10.0.5) and just see a red icon, same thing happen if i just open a title in fcx and try to "open a copy in motion", without doing anything,
-
Hi I am using FM to create the sales order. I need to check the completion of the created sales order. Is there any function module to do this. I cant find any export parameter in the above FM which gives the same. Regards Anandan
-
Upgrade from CRM 5.0 to CRM 7.0 MY Worklist Worklist
Hello, we're upgrading from CRM 5.0 Interaction Center to CRM 7.0. The client is using MYWORKLIST in CRM 5.0. In CRM 7.0 I found following three options for Worklist in Navigational Bar: CH-WORKLST CT-WORKLST ICM-WRKLST Please let me know which one
-
Hi Gurus I know that when you wanna upload a original of other module like MM, SD, PS... you have to do following steps: - Create a master data in other module - Create a document in CV01N - Attach some original application file - Use object link to
-
Keep asking me to uninstall and reinstall the product.
Keep asking me to uninstall and reinstall the product. How can i solve it? Thanks