Satellite A100 - Broken headphone jack

Hi,
Through obvious neglect I have broken the plastic headphone hack on the front of my A100 till still accept a jack but is barely staying in there.
Anyone know if its easily replaced by myself with a soldering gun and the part? How is it connected to the board?
thanks

Hi!
Normally the headphone jack is soldered/fixed on the mainboard and that means you have replace the whole mainboard. Furthermore the notebook must be disassembled complete and this is a little bit tricky.
In your case I would go to an authorized service provider. Speak with the technician and then you will see what they can do for you and how much it costs. I think this would be the best option.
Bye

Similar Messages

Toshiba Thrive Tablet Broken Headphone Jack Fix For Audio Line Out

BROKEN HEADPHONE JACK SIMPLE FIX FOR TOSHIBA THRIVE TABLET:
I love my Toshiba Thrive tablet. I take it with me everywhere I go, nearly every day. I also enjoyed connecting the headphone output jack on the side to an external set of speakers. I would enjoy stereo internet, video watching and so on. I recently broke (cracked) the headphone jack on accident. For months, I heard only through the small, factory installed speakers which, is not quite what I'd call 'ideal stereo.' Has anyone else done this? Despite trying to find repair shops locally, no one will touch a tablet it seems for repair or replacement parts. It's not your usual headphone jack. But - I can tell you how to get your sound back!
THE QUICK FIX
While browsing the internet, I found a device that by-passes the headphone jack and instead uses the internal workings of the Thrive tablet's main connection port. This port is located at the base of the unit. It will be covered by a protective, plastic tab that is removeable. Simply pry a little. This long narrow port was designed to allow you to set the entire Thrive tablet into a docking station designed for it. In this docking station are various connection pins that allow the audio to be sent out of the tablet and into the docking station. At the rear of the docking station you'll find a host of connection types: 1) audio out jack/headphone 2) USB 3) HDMI 4) 110v power supply. Simply plug your speakers or headphone cable into the new docking station and you're done! Your audio will work again. I purchased my docking station for $6.00 on Ebay. Oddly, the unit doesn't charge very well if at all while in the docking station but I've read you can simply remove the cover from your Thrive, remove the battery physically for a few minutes, return it to it's rightful place then close the cover and this fixes the problem. It's a strange little glitche. I have yet to try this yet. I did find that if I plug the cord directly into the Thrive right side as designed, it will recharge the battery as usual. I ordered a few of these docking stations which allow me to simply set the pad down depending on where I am and it will continue to charge. The docks do not come with power outlet so you'll need to consider buying additional but it works wonderfully. There are now even wireless docking stations too!
Attachments:
thrive-dock-rear.jpg ‏23 KB

HELP ..... can anyone help me please, my headphone jack is damaged. the metal around the headphone jack broke off and into the tablet. if i wigggle the headphones into the broken jack i can hear sound but if i remove the headphons i can hear nothing!!! I believe its stuck in headphone mode. the headphones wont hold inside the jack so im stuck with a tablet and no sound

Can I disable broken headphone jack? and get sound to internal speakers?

HP G72T-200 CTO Notebook PC WINDOWS 7
My laptop has a broken headphone jack (piece of plastic fell out of it) and thinks there is something plugged into the jack and won't default to the internal speakers. I've rolled back, reloaded drivers, run audio sound fix it thing, etc. Headphones will work if you hold plug and jiggle to the side. Is there anyway to just disable the jack so I can hear sound through the internal speakers?

Hey TR,
21Jan...
Can you stick a powered speaker on that jack and fix it so it doesn't wiggle much until you can get it fixed?
22 Jan...
The only fixes I have found for this are for Linux.
One can risk a registry fix, though I've not found a sure way to do it. The fix depends on knowing your sound card (I do not), and knowing the exact entry fix (I might, but I won't risk your system).
My sage advice is to get it fixed and be done with it.
It is my pleasure to assist.
Say “Thanks!” by clicking the Kudos Star to show your appreciation for the help.
Fixed? Mark this Post “Accept as Solution” to help others find the answers.
Note: You can find “Accept as Solution” only on threads started by you.
Kind Regards,
Dragon-Fur

Broken headphone jack shuffle

broken headphone jack. lots of static

deggie wrote:
How would making a Genius Bar appointment, going to the Apple Store, having them confirm the problem and give you a new/refurbished iPod (depending how old yours is) take longer than waiting for it to be shipped?
For those of us who would have to drive several hundred miles to get to a Apple Store, it would definitely take longer!
Personally, I don't even want a refurbished iPod, ever. If it's my only option, then I'll go with it, but I would prefer my own iPod. I don't even know this ... but when you get a refurbished iPod, is the screen brand new? Or is there a chance of getting a refurbished iPod with minor scratches on the screen? If that's the case, I'd probably just keep sending them back and refusing payment on the previous shipping charge until I got one with a new or immaculate screen. I always use a screen protector, and I can't stand iPods with scratches on the screen. Especially if you're going to view video on it.

Any clever solutions for a broken headphone jack ?

Wow. My year and a half old, always babied, iPod has a broken headphone jack. Probably not an uncommon issue, but what are my options?
Is this a repair that my local Apple Store can handle or would I have to resort to some third party repair guru?
Any chance of replacing the jack myself?
Also, is it possible to take the audio from the docking jack on the bottom of the Pod and then use some funky adapters to get signal to the headphones?
Just wondering what clever solutions some of you have found.
Thanks to all.
iBook / MacMini Mac OS X (10.4.5)
iBook / MacMini Mac OS X (10.4.5)

You can use the Apple Remote/FM Radio that connects to the dock connection and listen to it that way.
You can have Apple repair it for a fixed rate, or you can go to http://www.ifixit.com http://www.ipodmods.com http://www.iresq.com and either have them repair it or order the parts and do it yourself.

Broken headphone jack in ipod.

My headphone jack broke inside of my ipod touch. If I brought it to the apple store would they be able to fix it?

Maybe here:
Broken headphone jack! 3.5mm dillemma....: Apple Support Communities
However, I would first make an appointment at the Genius Bar of an Apple store and hear what they have to say.
Apple Retail Store - Genius Bar

Broken Headphone jack

Hello,
Last Monday, I noticed my ipod touch was broken. The headphone jack would no longer work. The songs were playing but no sound come out through the headphones (tried a few headphones I had lying around).
It became obvious to me that it was a hardware issue when I restored the ipod firmware. Besides, when i slightly moved the headphone jack out of its port i could heard sound through one of the channels.
I ordered the replacement box through support's site. However, the ipod returned to normal functioning on the following day, when I upgraded to 1.1.4. However this morning it happened again, and again this afternoon the ipod turned back to normal behaviour.
I will send it back to Apple on Monday however I'm afraid the tech stuff won't be able to reproduce the problem, since it's quite random as I have explained.
What should I do? attach a note inside the ipod box?
Call support even though phone support has expired (past the 90 free days)?
thanks
Ps. I'm in Spain so going to a genius bar is not an option

Just great ¬_¬
They received the iPod today and after just 1 hour they claim "no trouble found" and reshipped it back to me. Now i'm trying to get hold of tech services to let them know (Again) about the random nature of the issue

Broken headphone jack! 3.5mm dillemma. Help. Please.

Hi.
So my headphone jack has broken off clean into two pieces.
The trouble is the 3.5mm jack protuberant is now stuck inside my iTouch and due to the amazing self-locking mechanism of earphone/headphone ends, it will not come out, whatever I do.
Tweezers have not helped, neither has a small magnet.
I'm glad I gave up on the magnet for I have now come to know that the hdd is right next to the earphone socket.
Anyway, I need help.
How do I get that broken-piece out of the socket?!
Please. Help.
Many thanks, in advance.
- AP.

Guys,
It is done! It's out! I have achieved what surely seemed impossibe. I mean the things I tried with my iPod Touch, be it tweezers, pliers, glues, toothpicks, ear-buds.
I read about all of these wondorous ideas and plans online, to take out that unholy peice of metal lodged in my iTouch socket.
But anyway, yesterday you guys gave me some good tips. I was about half-way in the decision making process of making appointment with The Store and almost about ready to dive into what Alex suggested up here.
But then this evening, something made me go back to glue.
Glue, the creation of the century. Or well, maybe last century, or the one before that, I'm not sure when glue was dicovered/invented.
Anyway, getting to the point. It's out.
All I did, was make another failed attempt with the squared-off end of a tooth-pick dipped is some superglue. Like always, it stuck to the little golden 1mm protuberant like a charm. One pull, and it came off, while the thing was still lodged inside.
I went back to the headphones. I saw the broken off jack and realized, there was a bit of a cavity at the point where the jack had broken off. So I gave a tiny squeeze to the superglue pen and filled the cavity with just about a single drop of glue. Next, I rammed the headphone jack back into the socket.
I swear I wasn't expecting anything to happen. Barely 10 seconds into the "Eureka attempt", I don't know what came over me and I just pulled on the cord.
And there it was! IT WAS OUT.
Simple. Effective.
The solution always is right next to the where the problem began.
I should add, the speaker on the iTouch works fine, like everything else.
BUT, when I plugged in my new headphones, there's no output to the RIGHT channel.
I must say, this makes me sad. I don't know if I messed up something with the glue or pliers. Can't say.
I might have done some damage to those tiny silver dot like things on the socket wall which act like the self-locking mechanism for earphones/headphones.
Anyway, if it does end up working again, I'll be sure to let you guys know.
Many thanks again for the help.
Cheers.
- An overjoyed AP.

Satellite L745-S4210 Headphone Jack

I had my headphones plugged into the headphone jack of the laptop, and I accidentally stepped on the wire of the headphones, which pulled the headphones out of the laptop. When I went to check the laptop jack, it seems to have been moved out of place, and when I try inserting it back in, it just ends up being loose and not plugging in. The headphones itself have a bent jack, so I'm guessing it ended up dislocating the jack of the laptop.
Is it simple enough to just open it up and hopefully try to put it back in place?
Sound still works normally without the headphones, and if I can somewhat nudge the headphone's jack into the jack of the laptop, I can hear about one second of sound through the headphones until it goes back to just playing through the laptop's speakers.

You describe a part being pulled out and sits loosely, the headphone jack, like the one pictured here.
No to all of your questions and wishful thinking, even if it could e done, would you trust yourself with a screwdriver and an L-Series ? Y
You know that L Series are sought because of their premium brushed finish, heavier weight and sturdiness just like people who want metal Glocks instead of the plastic version used by commoners.
You're obviously unqualified to dis-assemble a laptop anyway, the "L-745" doesn't mean "Lego's"
It can be replaced with parts from radioshack by a skilled solderer.
Other alternative is blue tooth speakers.
http://www7.pcmag.com/media/images/262780-toshiba-satellite-l745-s4210-top.jpg
"hello, hello, IS THIS THING ON ?!?!!??!!! --Mr. Tinkles "

Disabling broken headphone jack

I own an Acer Extensa 4620z laptop with Intel Corporation 82801H (ICH8 Family) HD Audio Controller for my audio output. I had broken the headphone jack a while back, and have typically been bypassing this problem with an external Behringer UCA202 USB soundcard. The computer consistently believes there are headphones plugged in, and only currently outputs to the broken jack. Arch recognizes the card, but unlike other distros isn't really letting me set a specific preference to the UCA as opposed to HDA-Intel. I am using ALSA without any OSS. The system lets me order the priority of audio devices, but does not seem to actually route the audio output to the USB card.
I am not sure what to post that would be relevant in config, but I am happy to provide any info recommended.

@mrhmouse: the file is completely blank. I am now looking into configuring asoundrc, but any recommendations are nice.
@Pajaro: Is it capable of blacklisting specific components of the hardware though, or just all of HDA_Intel? I know it's picky, but at times it'd be nice for the speakers to work, just wish to disable any headphone output. In relations to my UCA202 working, I guess the blacklisting would work well... I'll look into it.

Satellite C850-A628 Headphone jack on my toshiba satellite doesn't work.

Satellite C850-A628
Hello,
Headphone jack on my toshiba satellite doesn't work. When I plug my headphones in the computer speakers still play. I know its not the headphone because they work on everything else I've tried. When I go to control panel > hardware and sound > sound it doesn't show the headphone jack. It only shows speakers. how do I get my headphone jack to work?

Satellite C850-A628 (PSKCV8-0T00XAR)
This is actually the peer support forum for Toshiba USA. But, while you are still welcome here, yours would appear to be a Toshiba Middle East model. Toshiba Middle East is really handled by Toshiba Europe, and you can find their forum here. You may want to consider using that in the furture.
I am not sure this will work on your system, but it's worth a shot. With your headphones unplugged, click on 'Start' -> click on 'Control Panel' -> click on 'Realtek HD Audio Manager'. Look for the file folder icon near the top right of that window, as in the attached pic. Make sure the check mark is on 'Enable pop-up dialog, when device has been plugged in' -> click 'OK'. Now, plug in your headphones -> when you see the 'The current connected device is:' dialog box pop up, put the check mark on 'Headphone' -> then click 'OK'.
Test your headphones again, and see if your laptops internal speakers now turn off.
Let us know what happens. Good luck.
Mike

27" imac 2013 broken headphone jack

Hello, has anyone experienced their headphone jack on the 27" imac 2013 becoming unusable?
I plugged in my headset and the plug wouldn't seat any longer.
The internal speakers work but that's it.
I managed to get it working for a bit but then couldn't find tha sweet spot it's not working again.
It is noted that this is the headphone/optical audio port so there's no other optical port on this unit.
Bluetooth isn't picking up my bluetooth headset either.
ej

The headphone port actually is an optical out unit. As a result, if you accidently hit a small inside trigger to switch between optical and non-optical mode, you can in fact create problems if that switch gets stuck. The Audio Midi Setup application in Applications -> Utilities may fix the issue with switching to 44 Hertz on output.
Sometimes resetting the PRAM can help as well:
http://support.apple.com/kb/ht1379
If it doesn't, you may need to bring the machine into service.

SVF15415CDB Physically Broken Headphone Jack

Earlier today I was using my laptop to watch a video when my dog ran into the headphone cord and yanked the laptop off my table. It fell around 4 feet and landed on the plugged-in headphones which broke off inside of the jack. After using tweezers to remove the plug I no longer can get sound to come from my internal speakers, nor from a different pair of inserted headphones. Is there any way to fix this issue by myself of will I need to get my laptop serviced?

Hi MattJack,
Welcome to Sony Community!
It's possible that the headphone jack damaged from that insident, this part is attached inside the laptop. what i recommend is to bring it to an authorized repair center to have it replaced.
Unfortunately, we are unable to assist customers outside of the US. We kindly recommend visiting our Sony Global Web site for information on contacting the Sony Support Center in your region at http://www.sony.net/SonyInfo/Support/.
Regards,
Jen
If my post answers your question, please mark it as "Accept as Solution"

Broken Headphone Jack- Using Speakers Instead?

Hey All,
I recently snapped off the last one-third of a 3.5 millimeter headphone jack into my Macbook's female port. I have been unable to dig it out with various needles and tweezers, and will take it to an Apple retail store sometime soon. If they can't do anything, I'm thinking of putting a dot of epoxy or Krazy Glue on a toothpick. :/
Anyway, is there any method by which I can, in the meantime, play audio through my internal speakers? To the computer, it's just as though I have a pair of headphones in...is there a way I can get around the Macbook's instinct to play music through the headphones when they're plugged in?
Thanks~

A method that I and others have successfully used is to remove the top case to get access to the jack. (The jack is the hole in the side of the MacBook, you broke a plug off in that jack)
The jack is plastic encapsulated but you should be able to create a tiny hole in the end of that jack into which you can insert a small pin or nail of sorts that you can use to push the plug out of the hole.
I like to use a red hot pin to melt a hole in the plastic end of the jack.
The problem with using glue is that it is very easy to get glue where you don't want it.

Satellite A205-S4777 headphone jack doesn't work

My headphone jack doesn't output any sound when headphones are plugge in. Instead the sound is played throught the speakers when headphones are plugged in. Any suggestion on what to check or do?
Solved!
Go to Solution.

Let's try reinstalling your sound drivers.
Realtek Audio Driver for Windows Vista(v6.0.1.5406 Logo; 05-17-2007; 17.84M)
- Peter

Satellite A100 - Broken headphone jack

Similar Messages

Maybe you are looking for