Satellite A100 - high temperature

Hello,
I have an A100 less than one year old and I noticed from the beginning that it has a tendency to be very hot (I almost get burned just putting my hand below the on/off button.
At first I didn't bother too much but now it's getting worse. I have run an Everest test and it says 89C for the processor temperature?!
Please advise.
Thanks and best regards

Hi
Well what to say... in fact the temperature is a little bit high but the notebook supports an overheating protection and should shuts down automatically if the temperature increases the critical level.
You said the temperature is higher on the notebook side where the power button is placed??
This is nothing unusual because on this notebook side the cooling modules and the CPU are placed.
There is an air circulation and the warm air flows outside.
The notebook bottom and the side are always warmer as the other notebook case parts.
Therefore it's not advisable to use the notebook on the knees but only on the desk!!
You should always be sure that there is enough free space around the notebook for properly fresh air circulation.
You know, after one year of working the dust and debris could has a bad influence on the fan rotation and notebook cooling.
Maybe it's necessary to clean the cooling modules professionally. In such case you should ask a technician for the help!

Similar Messages

  • Satellite A300 - High temperatures and overheating

    Hey there
    I own Toshiba Satellite A300 for one year.Lately I have noticed overheating.
    In the idle the lowest temperature I have measured using HW Monitor was 60C for CPU, 50C for GPU, 42C for HDD. When I have more applications opened it rises to 83C for CPU and 62C for GPU, during witch system performance is pretty slow. Bottom part of housing is quite hot even keyboard is hot and it's quite uncomfortable.
    Any idea where could be a problem? Should I put it into service? Thanks for reponses.
    Andrew

    Hi
    You should not send it to an authorized service provider you should clean your notebook from time to time!!!
    I recommended compressed air spray. Blow gently and shortly the air trough the holes of the case of the machine where the air flows trough. This could remove the dust from the cooling ventilators.
    This procedure should be performed every 3-4 months to ensure a proper operation and avoid system errors.
    I always used compressed air spray and I never had problems as yet.
    Bye

  • Satellite P300D-10V - Turn off by high temperature

    Hi!
    I have a TOSHIBA Satellite P300D-10V and I have a problem with overheating! When I load my CPU with 2,2 GHz for a long time, it turn off by high temperature!
    What must be my solution about this problem?
    "Normal" temperature for my laptop is around 70 - 75 degrees cslsius! Is it normal for this CPU?
    I have used another laptop with Intel CPU and there is no such problem! My Toshiba is in use for 2 years! OS Windows Vista Home Premium 32bit
    REGARDS!

    Hi alexander79,
    First of all you should know that cleaning the fan is not covered by warranty!!! Of course you can do this from an authorized service provider but for this service you have to pay, its not free!
    More detailed instructions you can find in this how to article from Toshiba:
    [How to clean the cooling system of a Toshiba notebook? |http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=40]
    As you can read, the notebook should be cleaned every 3-4 months and believe me, you will be very surprised how much dust come out ;)
    Last but not least its also important that you only use display drivers from Toshiba.
    I had also a problem with overheating and this was caused due a wrong display driver (I used the drivers from nVidia page). They are not pretested and dont have an overheat protection The result was overheating and turning off.
    After installation of Toshiba display driver the problem was solved.

  • System frequency on a Satellite A100-01L notebook should always be high

    Hello,
    Because I am a battlefield gamer there is a speed problems with my notebook.
    It is a Satellite A100-01L notebook with 1.73 GHz normal system tact. (2 GByte RAM, 120 GByte HD).
    The system frequency changes between 800 MHz (without hard job...) and 1.73 GHz (if it seems to be necessary). In the system BIOS its possible to select a 800 MHz (named slow ') or a dynamic clock speed (called: 'dynamic' modus).
    My question is: was it possible to set the system clock always to 1.73 GHz?
    Thank you.

    Hm, usually there should be also an option "High" or something like "Always High". So, I suggest you to perform a bios update and then to check if such an option is available.
    Otherwise you should look into the toshiba powersaver and make sure that everthing is on maximum.
    Greets

  • Satellite A100-159 - FAN is always on

    Hi,
    I have bought Satellite A100 159 with T2500 and Radeon x1600.
    Fan is always ON. I have upgraded bios and it didn't help. What is more, when I set ATI driver to use PowerPlay and when the battery is low I get only some scratches at the desktop and the computer restarts. Windows shows that there was problem with unknown driver.
    What can I do to stop the FAN - my CPU temperature is 28-31 cellsius and the frequency is always set to 2000 MHz (everest shows 1995 MHz).
    I think, that fan shouldn't work while the temp is so low. My old centrino has almost always 40-50 degrees and fan is always off.
    What can I do more to make the fan work only when the temp is higher than about 40 degrees?
    Kind regards
    I have to add that my old Acer TM 4502 with Centrino has SpeedStep which makes CPU to change his speed from 500 MHz to 1600 MHz. I would like to do this with my new Satellite - it would help me with fan problem. If I change the speed of the CPU than the temp will be lower and the fan will not run all the time.
    I noticed that fan is shutdown when I start computer at the morning when is cool. After windows start when the temp rizes fan starts and doesn't stop.
    Kind regards

    Hi
    The Toshiba power saver is responsible for the CPU and Fan controlling.
    Please open the power saver mode which you use, choose the tab basic setup and change the option Cooling method to a lower level. Furthermore you can change the CPU control method to auto.
    This procedure should helps to change the fan usage.

  • Memory upgrade on a Satellite A100-912

    I own a Satellite a100-912 and I want to upgrade its memory!
    As it seems, this model supports only PC2-4200 DDR2 SODIMM modules (533 Mhz). Before bying a memory module that might regret, I want to know if there will be any compatibility issues if I use to this laptop PC2-6400 DDR2 SODIMM module (800 Mhz).
    Is it going to work even at lower clock speed (533 Mhz) or is it going to be a total waste of money?

    As far as I know the FSB is able to handle 667Mhz modules.
    You can use lower modules (533Mhz) without any problems but modules with higher Mhz will not run with full speed due to the limited FSB.
    So I dont recommend buying 800Mhz modules. Firstly they are not supported and secondly its waste of money!

  • Satellite A100-847 - upgrade advice

    Hello,
    I'm using Satellite A100-847 (PSAA9E) for almost two years now. 2 year warranty period be over in month, so I guees it is good time for an upgrade. I could use more RAM and a faster HDD (for CAD purposes mostly when I'm on the run) so I would like to know more about it.
    *What I already found out is that my notebook:*
    (please say if I'm wrong with something)
    1) ...Can take 2 modules of So-DIMM DDR2; max 4GB; which means 2X2GB. I already have 2X512GB, and this is not enough.
    - The question is which DDR2 memory!? The FSB is running on 667 MHz, so I guess I should buy PC-5300/667 or even 6400/800?
    - Which is the best memory for my notebook? The one which doesn't heat up a lot!? Which model is cool enough?
    2) ...Has a Hitachi Travelstar 5K100, 2.5", 5400RPM, 8MB cache, 100GB SATA drive. Capacity is enough for me, but it is way too slow. So I guess I should for a 7200RPM 16MB cache drive.
    - The question here is does my notebook support SATA2 or is it just SATA1? Which shlould I buy?
    - Does my notebook support 7200RPM drive?
    - Will my notebook overheat with this drive?
    3) ...Could have a more efficient cooling system. Is there any solution to this?
    Thank you in advance,
    adambar

    Hello
    Googling around Ive found follow information:
    The computer has two SO DIMMs slot comes standard with DDRII 4200 module. It
    supports PC2-4200 and uses SO DIMMs (DDRII SDRAM) driven at 1.8 V, accepting
    BTO/CTO for your memory requirements. It can incorporate up to 4 GB of main
    memory.
    Using the following sizes of memory modules:
    256 MB (16M168P)/533/667 MHZ
    512 MB (32M168P)/533/667 MHZ
    1024 MB (64Mx16x8P)/533/667 MHZ
    If you want to use maximum RAM you must use two 2 GB. Toshiba recommends using
    2 x 2 GB PA3513U-1M2G DDR2 RAM. Alternative to this RAM module are high quality Kingston memory modules.
    About HDD I can say follow:
    The HDD interface conforming to Serial ATA (for 40/60/80/100/120 GB).
    The computer accommodates one 2.5-inch HDD with any of the following storage capacities:
    40 GB (9.5 mm thick) SATA (5,400rpm)
    60 GB (9.5 mm thick) SATA (5,400rpm/7200rpm)
    80 GB (9.5 mm thick) SATA (5,400rpm/7200rpm)
    100 GB (9.5 mm thick) SATA (5,400rpm/7200rpm)
    120 GB (9.5 mm thick) SATA (5400rpm)
    As far as I know SATA2 is backward compatible and theoretically you can use it but I am not sure about that. If I were you I would by SATA1 HDD.
    As you can see Toshiba has tested 7200rpm HDDs with this notebook model and you can use it too.
    Overheat maybe not but I can imagine that plastic cover will be warmer than before. Be just sure the notebook is placed properly and nothing blocks cooling fan.
    More efficient cooling system? I dont know what you mean exactly butt you can try something like this .

  • Installing Linux system on a Satellite A100

    Hi - I am new to these forums so please be kind with my limited knowledge .  My partner has a satellite A100 laptop that has Windows XP installed on it.  Due to driver and upgrade probs - he now wishes to install a linux op system on it (Ubuntu).  When I try to install it gets to a certain point then freezes.  It appears the cd drive stops reading?  I have checked the cd driver, and also the installl disc and all ok.  I tried to install through windows but the same problem happened?  Any ideas or help would be appreciated.

    Hm, usually there should be also an option "High" or something like "Always High". So, I suggest you to perform a bios update and then to check if such an option is available.
    Otherwise you should look into the toshiba powersaver and make sure that everthing is on maximum.
    Greets

  • I don't know BIOS password for Satellite A100-528 PSAA2E

    hi..i have a problem...
    i have a laptop Toshiba SATELLITE A100-528 PSAA2E-01H00WGE....
    the problem is that i downloaded toshiba HW setup and i accidentaly set a password..
    .not a user password....it's propably supervisor password or bios password...
    .the thing is that i don't know what the password is...i boot up my pc and it don't let me get in windows if i don't type the password.....is there any way to remove the password ??
    it does not let me either boot from a cd or usb....i press F12 in order to choose to boot from cd or usb but it's still asks for the unknown password....is there any solution ??
    please answer it's critical !!
    thank you very much...

    >the problem is that i downloaded toshiba HW setup and i accidentaly set a password..
    >.not a user password....it's propably supervisor password or bios password...
    Thats weird because the BIOS or Supervisor password can be reset only by an authorized service provider.
    The BIOS password is a high security option which cannot be reset easily.
    So ONLY ASP can remove a UNKNOWN password.

  • Special RAM brand for Satellite A100 (PSAA9)?

    Hi,
    I have a Satellite A100-504 (PSAA9) with only 1 GB RAM. CPUZ says it's a Hyundai HYMP512S64BP8-C4 PC2-4300 module.
    I want to upgrade to 2 GB and was wondering whether I have to buy some special sort of RAM? Do I have to buy also Hyundai RAM or can that be a different brand? What about the specifications? Which RAM modules would be the best in combination with Vista and that Hyundai HYMP512S64BP8-C4 1 GB module?
    Thank you for your help!
    Bob

    One more thing: you can of course buy the memory modules from different manufacturers but be sure you use high quality product. I can recommend you also Kingston memory modules.

  • Compatible Battery for Satellite A100-204

    I can't find any replacement battery for my Toshiba satellite A100-204 Laptop. The original battery is a 4 cell recycable Li-ion PA3451U-1BRS. Everytime i look for this battery in google i only find it for the Toshiba M40.
    It allmost looks the same but i am not sure if it is. Problem with my battery is that it gets empty after one hour, and i need more hours ;-).Everything is still new though (got it last weekend), is this normal for a 4 cell battery?
    I would like a battery wich lasts longer, 8 cell or higher if there is. But i dont know wich ones are compatible and dont know how to look for it (actually i do. I aint no noob and allways find my stuff, but this doesnt work out the way i search). Looks like the laptop is a bit rare......
    Please help me find one that will fit, and be sure of it :-D.
    (Btw, I live in The Netherlands, if that might matter for finding the battery nearer.)
    Greets JK

    Hi
    I have investigated a little bit and it seems that these batteries packs are compatible:
    PA3399U-2BRS(6cell)
    PA3399U-2BAS(6cell)
    PA3478U-1BRS(9cell)
    PA3478U-1BAS(9cell)
    PA3400U-1BRS(12cell)
    PA3400U-1BAS(12cell)
    The charger time of the 6cell and 9cell batteries is about 4houers and the charging time of 12cell batteries is about 5houers
    Hope it helps a little bit.

  • Blue screen with ativvaxx.dll error when connecting video cam - Satellite A100

    Hi, everytime I connect my video cam, my system will crash and I get a blue screen stating that there is a problem caused by ativvaxx.dll. Any of you guys know how to fix this? I've got a Satellite A100 system, it's new. Any help is highly appreciated.
    Thanks.

    Cool that you have solved the issue and thanks for the info. Maybe it could be useful for other users.

  • Satellite A100-795 - Hard disk replacement

    Hi,
    I have a Satellite A100-795 (model: PSAANE-02D00JBT).
    HD = Toshiba MK1237GSX
    HD can only be partly read with recovery software (Active@undelete) and makes bad noises too.
    Wich SATA harddisk are possible and supported by the bios?
    I want to avoid buying a disk which will niet work in the laptop.
    Bios Version is 5.10 (Phoenix TrustedCore)
    Thans in advance for any help.
    Regards,
    Leo

    Hello
    Generally speaking on SATA interface there are no capacity limits anymore and that means you can buy every HDD that you want. Furthermore it makes no difference which BIOS version is installed, HDD upgrading is hardware based.
    Anyway, just choose the new HDD that you want. Only important thing is SATA interface and I would recommend a model with 5400rpm if you dont play games. Higher rpm producing more heat, etc.

  • Can I replace the hard drive in my Satellite A100?

    I have a Satellite A100-033 PSAANE, running Windows Vista Home Basic. The hard drive is 60G. I save virtually all my data onto an external hard drive, but even so the hard drive will eventually not have enough space for the growing number of programs which I have installed, the various temporary files, etc. For example, I would like to install VirtualBox and run XP ( Ido have a copy), plus Linux, and maybe some other operating systems, within it, but that is likely to eat up more hard disc space than I have available.
    Does anyone know if it is possible to take out my existing hard drive and replace it with another one of a higher capacity? Is this possible?
    I would have to reinstall Vista on the new drive, from the rescue disc which came with the PC. I don't mind doing this, but will Windows Vista be "recognised" when I try to install it on the new hard drive?
    Sorry if these questions sound naive, but I don't know how to put a new hard drive into a laptop, or even if this is possible. I bought the Toshiba in February 2007, which was just after Vista had been released. I wasn't given the option of XP: Vista was the only operating system Toshiba provided at that point. I was assured that a 60G hard drive would be fine for Vista, but I do have to say that I feel I was wrongly advised, and that Toshiba should never have released a 60G machine for use with Vista. Hence my wish to have a hard drive with a bigger capacity.

    Yes you can install a higher capacity HDD. I believe the A100 can take any size of SATA 2.5" HDD, so you should be able to install a 250GB or 320GB successfully.
    As for Windows, you can reinstall it using the Toshiba Recovery Disc that came with the laptop.
    Instructions:
    Remove the screw(s) from the HDD cover on the base of the laptop to access the HDD.
    Slide out the HDD
    Transfer the HDD cradle/mounts to the new HDD
    Slide in the new HDD and screw on the HDD cover.
    Turn on the laptop and press F12 to access the boot menu.
    Insert your Recovery Disc and choose the CD icon to boot from it.
    Follow the prompts to install Windows.
    Connect your original HDD to the A100 using a USB adapter to restore your files/documents.
    ps. Remember to backup your important files regularly. HDD's can fail at any time since they have delicate moving parts, even when new.

  • On battery my Satellite A100-233 runs only 1 hour

    Hi
    I would like to know if it is normal that the battery lasts only 1 hour. All I do is either browse on internet or use word doc. or power point presentation. I can't watch a dvd without using power supply due to the battery. I would also like to know which battery normally comes with Satellite A100-233.

    Hi
    Thanks a lot for the information as I thought that there was something wrong with the battery as the sales-person had told me that it lasts 3h 30 to 4h!
    My Satellite A100-233 belongs to the PSAA8E series. In fact the model number is PSAA8E-05J026G3. But I don't know what the battery part number is. What I found written on the battery were 2 numbers: 6027B0010101 and 64279026ASF. There was also: IEC S/N:6SA300J8T D48XW BATT 6 CELL with recycle Rev 3.00 SPS:V000061150 Date Code:J6054
    Where can I search to find out whether the part number is PA3399U-2BRS or PA3399U-2BAS?
    The batteries you suggested, if I go to the shop and tell him to give me one of them will be enough or it's better I take the laptop with me?
    PA3400U-1BRS High Capacity Battery Pack (Li-Ion, 12 Cell, 8600mAh)
    PA3478U-1BRS Extended Capacity Battery Pack (Li-Ion, 6000mAh, 9 Cell)
    Thanks for you help

Maybe you are looking for

  • Error while running test report

    I have just installed oracle application server 10g 10.1.2. on redhat linus AS4 on dell 64 bit machine. forms servlet works fine but when i use the following url to access test report It gives a very famous error error "REP-51002: Bind to Reports Ser

  • FND_REQUEST PL/SQL procedure with parameters

    Hi guys I have created a concurrent program, using PL/SQL procedure which has 2 in parameters. I am trying to call the concurrent program using v_req_id :=FND_REQUEST.SUBMIT_REQUEST('INV','OMS_POP_INVVALUES_P', NULL,SYSDATE,FALSE,l_on_date, l_org_id,

  • "lib/libfreebl3.so: version `NSSRAWHASH_3.12.3' not found"!!

    I'm trying to setup Sun Java System Web Server7.0 on the fedora11. And then I have a problem with "configuration failed". I get the error massage: **Apr 25, 2011 7:33:38 PM com.sun.web.admin.configurator.ConfigureServer main** **WARNING: /sun/webserv

  • Copy and Pasting Componets

    I am building a dashboard with 5 or so Tabs. When I try to Copy and Paste a componet onto the next tab container, it pastes it again on the original Tab. Is it not a good idea to Copy>Paste componets? How do I keep it from pasteing again on the origi

  • Searching for a PCI card that has RCA OUT for 3D goggles

    Hi All, I have a Quad-Core Intel Xeon 3.0Ghz Mac Pro with the ATI Radeon X1900 XT, and I'm wondering if anyone has knowledge of a PCI card that has RCA out. I ask b/c I'm using dual monitors and I need to hook up 3D Stereoscopy goggles that require R