Satellite a20 s103 wifi problem

Hi!
I have inserted a MSI mp54g2 mini pci wifi card into my Toshiba Satellite a20 s103 computer and it doesn't work properly. The signal level is very low, though i have been testing it in the same room where was my AP (dlink dl-624+). I found, that there are 2 cables inside the computer (brown and white) and two slots on the wifi card (aux and main). I do not know how I should connect them, yet I have tried all the combinations and none of them changed the signal level. I found also, that even if the antena is not connected at all, the signal level is the same.
Can anybody help me with this one??!!
Please help me!!!
THX :)

Hi Horwath!!
THX for a fast reply!
I connected the cables as you advised, but I'm afraid it didn't change anything. The signal level maintains at very low level, though I'm in the same room where my AP is :(
I have heard that some problems may occur, as my AP is from US and I have bought my computer in Poland, but I have tested the AP with a another notebook bought also in Poland and it worked fine!
At least I know now how to connect the cables :) Guys from shop didn't have a clue how to do it :)
So BIG THANX for that!!
[Edited by: admin on 04-Mar-05 06:57]

Similar Messages

  • Satellite A20-S103: LAN cable disconnected

    hi
    i cannot get access to my LAN or internet.
    I'm using a Satellite A20-S103 with a Realtek RTL8139/810x Family Fast Ethernet NIC.
    When I connect the Lan cable to the LAN port, appears the message "LAN cable disconnected".
    The same message appears using de ConfigFree-Connectivity Doctor.
    I changed several cables, used cables that worked on others computers and the message still there and no access to the router/modem.
    The LEDs near the LAN port are not lightning (neither orange or green, none)
    I have already read the posts here in the forum (and in others forums) and i cannot make the ethernet card work.
    Do you think the problem is with the card or the OS.
    Can you help me?
    Sorry for my English

    Check firstly if the LAN card was recognized in the device manager.
    Under Network Adapters you should see the LAN card.
    If there is an yellow exclamation mark near the LAN card then either the driver was not installed correctly or there is another serious error.
    In first case I would recommend removing the LAN card from the device manager and after new reboot you should try to reinstall the driver downloaded from the Toshiba page!
    Furthermore you should set the TCP/IP settings to automatic because the router assigns the IP address automatically.
    Please check this and report the results
    Good luck

  • BIOS flash for Satellite A20-S103 needed

    Hello,
    I need a BIOS flash for a Toshiba Satellite A20-S103 notebook. I already downloaded the one on the download site.
    But this one i can not use because i need windows to be installed. And that is just the problem.
    I can not install windows because the BIOS is not fully ACPI compliant.
    The BIOS version on the laptop is V1.10.
    To update i need a dos version to flash the bios.
    Is it possible to get a bios update which is written for dos?
    Thanks a lot,
    Jean

    i did Have same problem. found nice resolve on it
    Satellite A200 (PSAE2), all partitions killed (include hidden) so i can't use BIOS (windows based) update :-(((
    aim = win XP SP2
    steps:
    1) Win XP disk in CD, scsi drivers ICH8M_32bit on USB FDD (Mitsumi btw) attached to notebook.
    2) booting from CD. F6. When windows installator found ICH8M_32bit drivers. I am creating disk C: (NTFS)
    3) He begins to copy temp installations files. During this procedure it says what it couldn't copy all files from usb FDD to HDD. It says to me what i will have problems in sucesfully complete installation. In spite of that installator succesfully transfering windows files onto C:
    4) First planned reboot. I see blue death screen. End? Not so soon!
    5) i have begin new installation. Again give to installator ICH8M_32bit drivers from usb fdd disc.
    6) i choosed "leave current NTFS on C: without changes".
    7) This time all drivers from fdd disk has been transfered succesfully.
    8) After reboot installation of Win XP completed succesfully!!!
    Sorry for my unnative English

  • Satellite A20-S103 - how to find VGA driver?

    Hi people
    I am using WXP, I could not find VGA driver for my laptop. I know it uses trident cyberaladdin but I could not find its driver.
    How can I find it? Thanks.
    Faith

    Hello
    It is really strange you cannot find it. I found it in 1 minute only.
    You will find it on Toshiba support and download page under http://eu.computers.toshiba-europe.com Support & Downloads.
    In Product type choose option ARCHIVE.
    You will find display driver for your Satellite A20-s103 (PSA20E). It is Trident version 6.14.01.0010.
    Bye

  • Satellite A20-S103 - crackling noise with new HDD

    Hello together
    I upgraded my A20-S103 laptop with a Western Digital WD2500BEVE 250 GB hard drive running under Windows XP Pro.
    Since then I have problems with the sound and the mouse movement when the CPU usage is high.
    Lets say up to 50 % usage everything works fine but above I have cracking noise and the mouse sticks and makes jumping movements.
    The drivers and the BIOS are updated to the latest Toshiba versions online.
    After some time and alot of search I got also the hard drive running in DMA mode with the ALI IDE4008.exe tool so it is not that the hard drive is running in PIO mode.
    Further I think that the hard drive speed is low when the CPU usage is high.
    Please read also http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=89990&#89990 which is showing I am not the only one with this problem.
    Does anybody knows a solution?

    I agree with Akuma. You should try to update the BIOS and the chipset drivers and see if it works or not.
    It worth a try ;)
    Both you can find here:
    http://eu.computers.toshiba-europe.com => Support & Downloads => Download Drivers

  • Satellite A20-S103 and SDHC support

    Hello,
    Are there any chances to make my old A20-S103 support SDHC cards?
    I googled and checked Toshiba support page for the latest drivers but it doesn't seem to work.
    I know I can buy an external USB reader, but I'd like to use the built-in reader if possible.
    I hope it's just a matter of new driver, not the hardware itself.
    I'd appreciate any help regarding this.
    Thx

    I am 100% sure something like this is not possible. It is old notebook model and it is not supported anymore.
    You can try to install driver designed for some newer notebook model but I dont believe it will work.

  • Satellite A20-S103: No internet - no media connected when typing ipconfig

    Hi,
    A few days ago, i installed windows xp on my Toshiba (SA20-S103).
    I've installed all the drivers but the internet doesn't work.
    It keeps saying "no media connected" when typing Ipconfig.
    Does anyone know if the problem has to do with the drivers of the ethernet card (Realtek RTL8139/810x Family Fast Ethernet NIC) or with the chipset drivers. I've tried so many drivers, but can't solve the problem.
    greetz

    Hi
    Did you check if the LAN card driver was installed properly and if there are no yellow exclamation marks in device manager?
    From my own knowledge the message no media connected appears if the LAN cable was not connected correctly or if the cable is broken.
    Should check this too!

  • Mode, audio/video control buttons on Satellite A20-S103

    Hi,
    Can anyone tell me how to set this controls? (this controls buttons are on front of the notebook.)
    I don't have any more original cd which come with this notebook and i don't know how to set them. If i press any of this keys nothing happens. I'm not shore my be this buttons are related only with Toshiba Media Player, if yes where can i find it and download it?
    Thanks in advance
    Darko

    There are not so many drivers that you can miss it. Just download the driver for "Controls" which version is 2.6.2900 and remove the software you installed before so you can be sure that the downloaded one can be properly installed.
    I dont understand why it doesnt works. If you have XP and you installed it by using the "setup.exe" then I dont really dont know where the problem is..

  • Satellite P20 S604 WIFI problem

    I'm new to this wifi technology and I can't find the wifi driver and the atheros client utility doesn't work.
    Also when the computer starts I get a message Capi_Wrk module cannot start. Does this have to do with wifi?
    Also when I try to install wifi driver from the Toshiba CD the batch file ends with installation failed message.
    Please help.
    Thanks

    Hi
    Are You 100% certain that Your unit have a built-in wireless networkcard? Check the BTO-code in the bottom of the machine (looks something like this P4 3.00G/2X256/80G42/17WT/DM/LM).
    Check Your BTO and post it here - then we can see what is supposed to be built in Your machine.
    BR
    Tom

  • Re: Satellite A20-S103D: Is it possible to install a 120GB ATA-100 HDD

    In 2003 my Satellite A20-S103D came with a 40GB Enhanced IDE (ATA-5).
    Would it be possible to install a 120GB ATA-100?
    Thanks,
    E

    Hi
    The problem is that you will not find any official information about the HDD size limitation on the Toshiba notebooks.
    Such infos dont exist. I didnt find it on the Toshiba page.
    I found this thread in the Toshiba forum;
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=71877&#71877
    An user has suggested that the 30GB, 40GB, 60GB or 80GB HDD could be compatible.
    The other user from this thread has already use an 160GB HDD in the Satellite A20-S103
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=89990&#89990
    So maybe you are a lucky man and the 120GB HDD will run.

  • Can I establish WLAN connection with Satellite A20?

    Just bought a new desktop pc and philips ADSL wireless base station. Software running OK on both desktop and laptop but can not logon from laptop without cable being attached. Does anyone know if the A20 should do and if so how to fix / setup?
    And if it doesn't, what do I need to make it so it does? I can not see the WLAN in network or device manager. Got Wireless hotkey in add / remove programs though. (What's this?) Can'e see it in programs list though??
    Help me! Please!!
    Ta. Andy.

    It is not easy to give any precise answer because you have not written which notebook model you have exactly. Anyway I have found follow information:
    Satellite A20-S103 is WLAN ready
    Satellite A20-S103D is also WLAN ready
    To be sure about WLAN card please check at first bottom side. Every notebook with WLAN card on board (factory configured) has small WLAN sticker. Please check also entries in device manager under Networks adapters. If the WLAN card is not listed there you must buy one.
    You can use one compatible card and put it on the right place or use some external solution like USB or PCMCIA WLAN card.

  • Satellite A20-130: SD R2412 cannot read DVDs burnt in certain optical drives

    Hi,
    I've got a Satellite A20-130 laptop, running WinXP and Ununtu Dapper in a dual partition. My 2nd laptop is not Toshiba one. When I burned DVDs (DVD+R) with my non-Toshiba laptop and played them in my Satellite it all worked fine.
    However, when I bought a new optical drive for my 2nd laptop my Toshiba suddenly stopped playing the DVDs burnt in this new optical drive(I was using exactly the same disc brand and format as before-- DVD+R). I tried the old DVDs (the ones burnt in the laptop before the optical drive hardware was upgraded) and they can still by read perfectly fine.
    This problem applies to both Ubuntu and WinXP. Support from 2nd laptop says this sounds like a firmware problem with my Toshiba. I updated the driver for my SD R2412 Toshiba optical drive (which, according to the file manual, seems to fix a DVD-Ram compatibility issue). Now the drive occasionally reads some of the new burned DVDs (after making loads of noise and waiting for ages), but more often than not I get an error message saying the device cannot be read because the format is incorrect or the device needs to be formatted.
    This non-Toshiba laptop reads the DVDs it burns using the upgraded optical drive perfectly fine.

    Hi
    Satellite A20 is pretty old notebook model and after intensive usage it can be that drive is more sensitive. If all this happen occasionally there is no simply explanation why this happen.
    I know it is pretty annoying but I do not see any magic solution. At the end you must test it with brand new drive.

  • Satellite A20 - CD/DVD doesn't read any kind of disk

    I just received a used Satellite A20. Previous owner has uninstalled their programs, and now the DVD/CD does not read any kind of disk. It worked fine for the former owner.
    Satellite A20C-0231Q Windows XP - Home Drive SD-R2412
    In the bios a cd-rom drive is listed
    In the Contol panel the drive is listed but with a yellow triangle and message suggesting that the device cannot be used... driver problem?
    Is there a way to locate the driver for an older machine, install it, without doing a complete recover (since the cd drive does not work?)? I noticed that the driver listing started with Satellite A-200.
    Any suggestions will be appreciated!
    Thanks!

    Hi
    Normally you dont have to install another driver for CD/DVD drive. The preinstalled driver is a part of OS and must not be renewed or something else.
    Anyway, if your drive is listed in device manager with yellow exclamation mark you should remove it and restart the notebook. After this the drive will be recognized again.
    If it doesnt work you should follow this Microsoft workaround to remove the upper and lower filters:
    http://support.microsoft.com/kb/314060
    By the way, can you boot from a bootable disk?

  • Strange wifi problem on a brand-new MacBook Pro

    Hey there, I'm new here. Desperation has got the better of me, and I hope I can get some advice.
    So, last sunday I bought a brand new 13" MacBookPro with 2.8g i7 processor and 10.7.2 OS (I can't update to 10.7.4 because System Update tells me the download has been tampered with or corrupted after I waited 2 hours for it to finish, but I'm trying a direct download from the website). Here's the exact product: http://www.amazon.com/Apple-MacBook-MD314LL-13-3-Inch-VERSION/dp/B005CWIZ4O/ref= sr_1_5?ie=UTF8&qid=1340301247&sr=8-5&keywords=macbook+pro+13
    Everything is all perfect except for a strange wifi problem. Note that the wifi does not turn-on or off, it doesn't disconnect after 'sleep', it doesn't get less speed, it doesn't constantly leave a preferred connection (once I chose my home wifi it always connects to it no problem). The wifi bar is always full. What is wrong is that the internet is kinda 'glitchy'. The best metaphor I can think of is that it's like a car that has to be pushed down the road before the engine can start. Please, bear with me because this is kinda hard to explain and I'm not good at tech lingos.
    One of the symptoms is browsing can get really slow and inconsistent, almost as if the wifi gets turned off in the middle of browsing. For example: if I look something up on Google and then open 5 new tabs, probably only 2 or 3 of those tabs will eventually load while the other two will not get past the long 'http:.......google.....etc etc' address and will eventually show one of those 'error loading page because there's no Internet connection' notice. This happens a lot. Sometimes I have to refresh/retry loading a page a couple of times before it finally loads, then usually everything will get back to normal and I will be able to open multiple tabs with no problem, but in a couple of minutes I would try to open another site and the problem will start again.
    So I tried to see how it does with downloading using iGetter. Fortunately I also have a Macbook (white-plastic casing one) and my brother has an old 2006 MacbookPro so I can compare. With those two older Apples iGetter starts receiving data in less than 8 seconds after I click Start, while my brand-new Macbook Pro can take up to 15-20 seconds, sometimes it doesn't even start at all and I have to re-click the start button. But once the download actually starts (on my new MacBook Pro), it downloads like normal, it doesn't stop and the speed is also as good as I can get. Strange huh? Hence, like a car that has to be pushed before the engine starts.
    I also tried 'speed testing' from a website with all 3 laptops. On my old MacBook and my brother's MacBook pro, once I click 'begin test' it takes only a couple of seconds of 'ping' before the download/upload speed measurements start, but with my new MacBook Pro (just like with iGetter) it takes up to almost a minute before the measurements start, sometimes it won't start at all and I have to re-start the test.
    Well, thanks for reading. And hope you can help me shed some light into this. Because it is really preventing me from really enjoying my new MacBook Pro. And if this is most likely a hardware problem, I'd better get back to the store and try to get it replace or something while it's only been 5 days. *cheers*

    Hey guys.. Thanks for the replies. Unfortunately, I bought the MacBook in Indonesia where there are no such thing as an AppleCare. The only option is to leave the Apple product to one of the 'Authorized Apple care centre' and have whoever do whatever to it without guarantee of success. As for returning it and getting a brand new one, I also don't know if there is such a deal here, but that's actually a good idea, will try to go to the store tomorrow. Although, I'm worried that the problem might be with OSX Lion or something and getting a new one won't help.
    mark75090, I've tried resetting the router when I first noticed te problem, didn't work though. I've checked my new MacBook's wi-fi (option+click wifi bar) and it says 'PHY Mode: 802.11g', so does my MacBook and the old MacBook Pro. I don't know what those mean though, and I don't know whether or not my router is an N., can you tell me more please.. I have tried with the other two turned off, and only the new MacBook using the wi-fi but the problem persists. I have also tried connecting directly to the router, but as I described, the problem is too subtle for me to notice the difference.
    Also, if I create a brand new Wi-Fi connection in network preferences and connect to my router through the new Wi-Fi profile, the problem seems to be gone for an hour or so, then it always comes back though. I have also just finally installed 10.7.4, but it doesn't help either.

  • Wifi problems still exists?

    I sold my gs60 that had an 870m back in january mainly because i couldnt bare the wifi problem. I really loved the laptop and everything about it but everytime my laptop overheated the wifi would drop from 100mb to 1mb or less at times, monday im thinking of buying a new msi laptop and im wondering if these models that are currently being sold on amazon and etc still have the wifi problem or has it been fixed?
    And trust me, i read the forums, i read the guides and im pretty decent with computers/software and etc, i uninstalled, reinstalled, updated it, changes adv. settings and even though it improves certain things the problem was still there. So does it still exist?
    Or should i just buy a USB wifi?

    This problem only occurs in earlier patches of Intel WiFi card of GS60 2Px (8xx series of NVIDIA graphic cards) and not every unit was affected.
    If you don't want to take this risk, I'll suggest you buy GS60 2Qx (9xx series of NVIDIA graphic cards).
    USB WiFi is a good idea. It certainly has a better signal comparing to the WiFi embedded in the body of the laptop.

Maybe you are looking for

  • Settings still don't retain.

    So, it's 3.0.3 already but one of the most importal features still doesn't work. Seriously, how hard can it be to fix it?

  • Reporting Services 2012 - "Database is up to date, but some sites are not completely upgraded"

    Running SharePoint 2010 SP1 (Feb-Mar 2012 CU) Is there any official word from Microsoft regarding the issue with SQL Server Reporting Services 2012 for SharePoint where 2 of the reporting service application databases show "Database is up to date, bu

  • Receiver File CC error

    Dear All I am using Java mapping to change the filename dynamically. I am getting follwoing error in my receiver file communication channel. Message processing failed. Cause: com.sap.engine.interfaces.messaging.api.exception.MessagingException: com.s

  • Infoset Query-concatenate fileds

    Dear Experts, How to Concatenate two fields into a local field in an infoset query. Regards Jogeswara Rao

  • Color Picker Stops Working in DW CS6

    Every so often, when I use the color picker from within Dreamweaver CS6 to select a color from an image or background, etc., then try to change that color (slightly change the brightness up or down using the system color sliders), it will act as if i