Satellite A200 screen has turned 90 degrees

I've got Satellite A200 and screen has turned 90deg .
Can anyone tell me how to turn it back please

What is the model number of your laptop? (PSAxxx-xxxxx)
Try pressing CTRL + ALT + UP ARROW

Similar Messages

  • Satellite A200 - Screen has a pink tint

    Over the past few months my screen has developed a pink tint...
    I'm wondering if it will get any worse - and whether it can be repaired?
    Any info would be much appreciated, cheers

    Hi
    Possibly its display malfunction.
    In such case only a part replacement could help you.
    You can also connect an external monitor to this notebook and could check if this would be noticeable on the 2nd monitor too.
    If external monitor would be affected, then the issue is related to graphic chip.

  • Display on my screen has turned 90% to the left on Equium

    Greetings from Scotland.
    I have a problem with my laptop display and wondered if anybody can help me.
    The display on my screen has turned 90% to the left, so the top of the page is at the left of the screen running to the right of the screnn instead of from top to bottom, anybody any ideas of how to fix it?
    regards
    kevin

    Hi
    Do you have a Intel graphic card?
    If yes then you could change the display position using this key combination:
    Rotate to normal: CTRL+ALT+UP
    Rotate 90 Degrees: CTRL+ALT+LEFT
    Rotate 180 Degrees: CTRL+ALT+DOWN
    Rotate 270 Degrees: CTRL+ALT+RIGHT
    If you are using another graphic card please check the graphic properties and advanced settings

  • My iPad 2 screen has turned a weird colour. The background is black and the letters are white instead of the other way round and colour photos look like negatives. How do I change it back.

    My IPad screen has turned a weird colour, the background is white and the letters white instead of the other way round.  Colour photos look like negatives. How can I turn it back to a white background.

    Dear Steve,
    You are wonderful! You are the best! I'm Stephania and I recently purchased a refurbished ipad2. I've had it for about 3 weeks now and updating & fixing it so my liking. The only thing that I couldn't correct were the photos that looked like negatives. Every photo, even on the internet, on apps, everywhere! I just couldn't figure out how to fix it. I contacted Apple Care and its too difficult to get in touch with them. I had looked through support before but didn't put in the right question. Well, today I got lucky. I did the two things you suggested and turning the "White On Black" off did the trick. I'm so happy! I had a feeling it was something simple and this is not even in the manual!
    stevejobsfan0123 wrote:
    Try triple clicking the home button. If that doesn't work:
    Settings > General > Accessibility > White on Black OFF.

  • My screen has turned black as if the LCD screen isn't working. There is no damage and the phone is still responding to vibrations and there is a dial tone when called. What is wrong with my phone?

    My screen has turned black as if the LCD screen isn't working. I have tried using the lockbutton and home button to turn it on, but it doesn't work. What should I do?

    Your phone is probably broken.

  • My screen has turned green how do I turn it back to normal

    my screen has turned green how do I turn it back to normal

    Use Settings > General > Accessibility > Zoom and turn this Off.

  • My ipod screen has turned white and I can't read it

    Ipod Nano screen has turned white and I can't read it

    Hello Redcoupe7
    Check out the article below and pick the iPod that you have to go over some troubleshooting options. If it does not work, there are options for additional assistance to assist you further.
    iPod Troubleshooting Assistants
    http://www.apple.com/support/ipod/five_rs/
    Regards,
    -Norm G. 

  • My iPhone 4S screen is suddenly not reacting.  The screen has turned a light blue color but nothing is happening. I have tried several things such as holding the power button, plugging it into the wall, and plugging it into my computer. What should I do?

    My iPhone 4S screen is suddenly not reacting.  The screen has turned a light blue color but nothing is happening. I have tried several things such as holding the power button, plugging it into the wall, and plugging it into my computer. What should I do?

    Sounds like the device was dropped at some point and damaged as a result.
    Take it to Apple for evaluation and a replacement.

  • My Macbook pro has stopped working and the screen has turned blue on static mode

    My Macbook pro  8.1.1 has stopped working and the screen has turned blue on static mode.
    I have tried restarts many times but of no Use
    Regards
    Nawabdera

    Try SMC and PRAM resets:
    http://support.apple.com/en-us/HT201295
    http://web.archive.org/web/20140711222006/http://support.apple.com/kb/ht1379
    Then try a Safe Boot:
    http://support.apple.com/en-us/HT201262
    Any help?
    Ciao.

  • My iphone screen has turned black

    Help my screen has turned black and can't get anything up on my phone

    See Here for  >  Frozen or unresponsive iPhone
    Try this First...
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    Wait for the Apple logo to Appear...
    Usually takes about 15 - 20 Seconds... ( But can take Longer...)
    Release the Buttons...
    http://support.apple.com/kb/ht1430
    More Info here...
    https://discussions.apple.com/message/19521062

  • Screen has turned white after I turned the laptop on?

    Help, my macbook screen has turned white after I turned the laptop on?

    Hello furniture103
    Start with the article below to troubleshoot the issue of just a grey screen. See if you can reset the NVRAM and boot to Safe Mode. Let me know how far you get to further assist you in getting your MacBook to start working again. 
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/ts2570
    Regards,
    -Norm G.

  • My ipad screen has turned color and looks "over-exposed" - help!

    my ipad screen has turned color and looks "over-exposed" - help!

    Settings > General > Accessibility > Invert Colors Off

  • My iphone screen has turned black, phone is still on as screen shots can be taken. When home button and power button are held - no apple icon will appear. Please help

    My iphone screen has turned black, phone is still on as screen shots can be taken. When home button and power button are held - no apple icon will appear. Please help??

    If this iPhone has had the screen replaced previously, possibly LCD Display connector has simply come loose from the Logic Board. Possibly the LCD Display is faulty and the front screen assembly needs to be replaced. If you have Warranty or AppleCare make Genius reservation or set up service and take or send to Apple. This is handled by Apple with Replacement iPhone 4S.

  • My ipod touch screen has turned white. the screen has turned bright white. it is not going by reseting also. when  i  shift screens then it leaves a trail and i dont know what to do. please help.

    my ipod touch screen has turned bright white. the things are visible but partially and when shift the screen it leaves trails behind. i dont know what to do help please.

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Satellite A200 screen stays black when trying to boot

    Hello everyone,
    My Toshiba Satellite A200 notebook is not working anymore, so everything started when I was playing a game, suddenly, the screen turned blue with some tiny text written on it. I had to hold the power button a few seconds to close it because nothing was happening on the computer. I then pressed the power button to open it. Everthing was going well, until the welcome screen. At this part, it was written "Welcome" but the Vista loading circle left of it wasn't turning.
    After a few seconds, I decided to close the computer again, so I did hold the power button so the computer closed. Here is the problem : I tried to reopen it, but the screen stayed black. Nothing was happening. The power light was blue, but not any computer activity. So I let it like that a few minutes then closed it and tried again, but the same thing happened. I tried to disassemble it and noticed one of the two memory card wasn't fully in its slot. I fixed it, but it didn't fix the problem.
    I also tried to plug another screen on it, but that one was also black. So I put back the screen on its computer and tried to boot my laptop and it worked. It was booting, but the first problem came back, the Welcome screen was frooze there. So yes I did close it again and then the same thing happened, the screen stayed black.
    I don't think the problem is the screen because as I said sometime it goes to the welcome screen. Also I don't hear any welcome sound when the screen stays black as if the computer would simply not start up. And as I said earlier, I don't see any computer activity on the little light in front of the computer. And left of this one, I clearly see that the computer is ON because the power light is blue.
    So this is my problem, next time the computer manages to start up I'll try to boot it on the SAFE MODE, but until then, I don't know what to do. Please, help me.
    Thanks in advance,
    MrRoy
    EDIT :
    After letting the computer turned off for about 30 minutes, I started it, and booted in safe mode. At this step, I securely closed my comptuer with the shut down button instead on holding the power button. Then I reopened my computer, and it booted and the problem was fixed. Now my notebook is openened and working.
    So if this is happening to you :
    1. Shut down you computer.
    2. Wait for about 30 minutes.
    3. Boot in safe mode
    4. Shut it down using the shut down button istead off holding the power button.
    That should work.

    Finally, it doesn't work. I don't know why but my computer did start up after the 30 minutes, but now it's not working anymore. It just won't startup like I said later, with a black screen.
    The computer did work for about half an hour. I mean, I managed to start it up but after executing a program, it just froze and I had to hold the power button to restart it. I did it about 3 or 4 times, then it simply did the black screen again. I think the problem is my processor, maybe it's damaged or something, could it be possible?
    Because I see that the processor isn't working when I try to start it up.
    So let's say it's damaged, would that be the symptoms of my computer?
    And if it's the processor, the only way to fix it is to send it to a reparator or something, because I don't feel like it, I'd rather do it myself.
    But right now, my computer is simply not booting, like I said in my previous post.
    Thanks in advance,
    MrRoy
    Note : The edit button wasn't there so I had to double post :/

Maybe you are looking for

  • How to clear alert when a null value is returned for a metric column?

    Hey all, Recently, I've encountered a problem about clearing alert when a null value is returned for a metric column. From Oracle official doc, it seems that NO_CLEAR_ON_NULL could be used for this propose. However, it doesn't. Here is the line from

  • PI 7.0 Hardware Requirements & Confirguration

    Hello, We are planning to install PI 7.0 on the AIX 5.3.x(64 bit) with database DB2 UDB 8.2.x.(64 bit) for a Sandbox environment. I am new to the XI area. I need some small/detailed information regarding following requirements( from PI BASIS point of

  • Reg:restart the completed task in human workflow

    Dear team, We are working on Oracle soa10g.We have a requiremnt on human tasks. once the task is approved/rejected in bpm worklist, immediately we need to get the task payload and status from BPMworklist and insert in DB. Using human workflow java ap

  • Taking snapshot of continuous waveform in oscillosco​pe

     my project was -labview front panel has to take the snapshots of the continuous waveform generated from oscilloscope.My front panel is able to take the main graph (which is not rolling or moving ) in oscilloscope and save it in a file in the form of

  • How do I reset Firefox when I'm blocked?

    I have the Ukash malware virus on my Mac, which blocks Firefox. I clicked on troubleshooting. Then pressed the reset Firefox button, but it wouldn't work. I can't even get the Firefox toolbar showing unless I access Firefox from Safari. I am writing