Satellite A30 always shutdown without any prior warning

Hi all,
i'm having a problem with my Satellite A30 notebook. It will always shutdown without any prior warning. But the thing is i don think its a heating issue with the fans. The notebook will only shut down if im running the laptop on high power or on full power by the AC adapter. Tasks that may be taxing like full system virus scan or playing games will cause it to shutdown after about 20 minutes again only on high battery power setting or if its connect to mains and is set on full power. Using word or simple tasks do not affect it.
Now im thinking there may be a problem with my cpu as it cannot handle it when it has to perform advanced tasks on my notebook. What could the problem be?? On low power my notebook will work fine even when its performing these advanced tasks it's only a problem when its on full or high power.
Any help/advice?

Hi
Thanks for the description I'm still thinking its a overheating problem.
The notebook power saver controls different power modes if the notebook runs with AC adaptor or with full power the power saver uses different power mode as when the notebook will run with battery only.
The different power modes support different CPU settings and different cooling method.
Probably the CPU runs with full performance and getting hot when the AC adaptor is connected.
I think you should check the cooling modules and fans. Try to clean it carefully with vacuum cleaner. But if you have no experience with such procedures then asks a technician or someone with more experience

Similar Messages

  • Satellite A205-S5803 (Shutdown without warning)

    I have Satellite A205-S5803.  It automatically shutdown after regular use of 2 or 3 hours without any warning.  I changed the hard disk yesterday because it shows the windows starting bar but not open the windows loging page and it shows mouse pointer and hard disk goes off. I treid to install new windows from recovery cd but it also load the window then hard disk goes off.  Then I change the hard disk and now problem is it automatically shutdown without any notification or warning.  I am very disponting due to this situation and don't these problems raise as my warranty over (my warranty finsish before 2 months).  I request to you kindly guide me properly what I do.

    Either of these two are for your computer.
       KTT667D2/2G
       KTT800D2/2G
    So far as I know they will work in Slot A, with Slot B empty of course.
    BTW, Windows Vista will barely work in 1 GB. Those computers should never have been released.
    -Jerry

  • Random price increase without any prior notification

    I was under the distinct impression that I was locked in for the same price for a full year.  How come Adobe can just raise the price from Student / Teacher $19.95 to $32.00 without any prior notification? Many people were suspicious on a subscription format but I defended Adobe on this thinking that it was great deal. Some of those suspicions are now coming true as Adobe raised the price.  We are locked in and cannot use any of the software unless we pay, it’s not like before when we had the software and could choose to upgrade whenever we wanted.  Adobe really got us this time.

    Hi Veronicaststudent,
    Thanks for your response.
    I would suggest you to buy the new subscription & you cancel the old one which is going to end March 14th.
    There will no cancellation fee as the 12th payment has already been paid.
    You can cancel it yourself or you can message me privately the old order number.
    Please check.http://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html
    Once you buy the new subscription, just log out & log back in of the CC desktop app to activate the new subscription.
    Hope it help the issue.
    Regards,
    Rajshree

  • Since 2012 I have Photoshop Elements always worked without any problem, however now the language is suddenly German how can this be changed, removed the program and re-installed, not working. Program is downloaded and updated via the apple app store?

    Since 2012 I have Photoshop Elements always worked without any problem, however now the language is suddenly German how can this be changed, removed the program and re-installed, not working. Program is downloaded and updated via the apple app store?

    I've done some research on the SQLite database. Whenever Aperture hangs up (like during auto-stack or opening the filter hud) there are thousands of SQLite queries happening. These SQLite queries cause massive file I/O because the database is stored on the disk as 1kb pages. However, the OS is caching the database file; mine's only 12MB. I'm trying to track down some performance numbers for SQLite on osx but having trouble.
    It's starting to look like most of the speed problems are in the libraries that Aperture uses instead of the actual Aperture code. Of course, that doesn't completely let the developers off the hook since they choose to use them in the first place.
    Oh, and if anyone is curious, the database is completely open to queries using the command line sqlite3 tool. Here's the language reference http://www.sqlite.org/lang.html
    Hmm, just found this. Looks like someone else has been playing around in the db http://www.majid.info/mylos/stories/2005/12/01/apertureInternals.html
    Dual 1.8 G5   Mac OS X (10.4.3)   1GB RAM, Sony Artisan Monitor, Sony HC-1 HD Camera

  • HPDM Update/Install Jobs on ThinClient ShutDown without any "Message"

    Hello,
    I want to send Update/Install jobs to our ThinClients which should be executed on "Shutdown" of the ThinClients.
    There is the possibility to check the box task deferment but if I check this box and send the task to the ThinClient, the user gets always an HPDM Message with the Job which can be delayed for the configured time, or to install/reboot directly.
    I dont want any informations. For example, I'll send a task to the thin client at 1pm and configure that this task sould run on shutdown of the thin client (normally the shutdown of the thinclient happens, if the user goes home from work), so the job can run after finishing time. So I won't disturb any users, and the jobs always runs after the user went home.
    I know, I could plan a job with wake on lan, but I've always trouble with wol. There are a lot of thinclients which are connected via VPN or something else... A wol packet wont reach this clients.
    Is it possible to send a "delayed" job without any informations ?
    Thanks and regards,

    Hey,
    I have posted a thread regarding the same issue.
    I have run the update myself (both for WinDVD Playback v5 & WinDVD Creator v3) from the System Update utility.
    Both reported as installed successfully on the System Update "Installed Updates" log though the update for WinDVD Creator v3 keeps showing up on the available updates.
    The version i currently have is version 3 so i guess the update went through, the path: C:\Program Files\InterVideo\WCreator3 - so y does it keep popping up on the available updates?

  • Satellite A30: Doesn't recognise any USB devices.

    My computer doesn't recognise any of the devices when connected to the USB Port on my Satellite A30. After dowloading SP2 I was able to install the printer but I can't use it because there is no printer icon on the tool bar. If i want to print anything i get the printer window, i select the print then it goes to MS Office Image writer. Basically, I can't use my printer or any other device connected to a USB port.
    However, It was working perfectly well when I had the XP home edition but I can't reinstall that one because there is something wrong with the recovery disk that's why I had to install the XP Pro.
    Also, I used to get a sound, letting me know that a device has been connected. I don't get that anymore nor the icon on the toolbar.
    Is there anything I could do to resolve this issue please? Is it possible to obtain another recovery disc somehow? Obviously this is something to do with XP Pro software but I don't know what to do.
    Could you please help me?
    Thank you!

    Hello Juan!
    This is what the problem is the only printer window i have is the MS Office Image Writer. I do not have any other printer window. If I use add a printer, then the wizzard can't detect a USB device.
    I have just checked the link you gave me and did exactly what it said but it just doesn't help. It is not just my printer, it doesn't detect any device i connect to it. For example, I can't update my ipod anymore because the computer doesn't detect the ipod when it is connected.
    I really don't know what the problem is! It was working perfectly fine before the upgrade and for the upgrade i have used the official MS Windows XP disk.
    You woudn't know how to format the HDD by any chance, would you?
    Thank you for your help

  • Macbook shutdown without any warning after 40%, when run on battery.

    Hello,
    My Macbook when run on battery after 40% shuts off without a warning. Is there a way to avoid it? Is there a setting in the battery preferences where I can change to avoid shut down?
    Battery Information:
    Model Information:
    Serial Number: DP-ASMB016-370e-4db1
    Manufacturer: DP
    Device name: ASMB016
    Pack Lot Code: 0002
    PCB Lot Code: 0000
    Firmware Version: 102a
    Hardware Revision: 0500
    Cell Revision: 0200
    Charge Information:
    Charge remaining (mAh): 2496
    Fully charged: No
    Charging: Yes
    Full charge capacity (mAh): 4276
    Health Information:
    Cycle count: 142
    Condition: Good
    Battery Installed: Yes
    Amperage (mA): 1488
    Voltage (mV): 12281
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 60
    Disk Sleep Timer (Minutes): 180
    Display Sleep Timer (Minutes): 45
    Automatic Restart On Power Loss: Yes
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Wake On LAN: Yes
    Display Sleep Uses Dim: Yes
    Battery Power:
    System Sleep Timer (Minutes): 60
    Disk Sleep Timer (Minutes): 180
    Display Sleep Timer (Minutes): 45
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Reduce Brightness: Yes
    Hardware Configuration:
    UPS Installed: No
    AC Charger Information:
    Connected: Yes
    Charging: Yes
    If you can suggest me with the above problem will be of great help. Thank you in advance.

    Same issues here:
    - When powering the MB on the battery, the MB can go off suddenly without warning, usually at about 20% but, since it started about 2 months ago, it occurred also at 7%, between 30 and 40% and even 70% once… It occurs every time when on batteries. And every time, if I start the computer again, it will shut down suddenly without warning after a few seconds/minutes. When back on mains, it can be powered on normally. It does not go to sleep, it's a complete and sudden power off without warning.
    - The battery at about 173 cycles sees its capacity dwindling way too much (it's been dwindling since day one, but it's going down faster and faster, the graph since November 2007 in MiniBatteryLogger is edificatory). The capacity right now is between 2900 and 3460 depending of the feel of the day. It's been calibrated regularly since day one in July 2007. Note that the capacity dwindled from its original capacity but never went higher than this value even if along the way it recovered sometimes more capacity.
    I have tried all the tricks from calibrating a little bit more often, reseted the SMC, even a complete system reinstall (that I wanted to do anyway as I had to get rid of the evil spotlight bug). All this to no avail.
    So what? :-/
    Model Information:
    Serial Number: DP-ASMB013-3629-1bbc
    Manufacturer: DP
    Device name: ASMB013
    Pack Lot Code: 0001
    PCB Lot Code: 0000
    Firmware Version: 0102
    Hardware Revision: 0300
    Cell Revision: 0200
    Charge Information:
    Charge remaining (mAh): 3320
    Fully charged: Yes
    Charging: No
    Full charge capacity (mAh): 3412
    Health Information:
    Cycle count: 173
    Condition: Check Battery
    Battery Installed: Yes
    Amperage (mA): -1
    Voltage (mV): 12411
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 0
    Disk Sleep Timer (Minutes): 0
    Display Sleep Timer (Minutes): 5
    Automatic Restart On Power Loss: No
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Wake On LAN: Yes
    Display Sleep Uses Dim: Yes
    Battery Power:
    System Sleep Timer (Minutes): 5
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 1
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Reduce Brightness: Yes
    Hardware Configuration:
    UPS Installed: No
    AC Charger Information:
    Connected: Yes
    Charging: No

  • HP Probook 4540s Sudden Shutdown Without any Warning

    I have a HP Probook 4540s laptop bought in November 2012. It has Core i5-3210M CPU @ 2.50 Ghz chip with 8 gb ram and 500 GB hard disk. Till 2014 it was all OK. But now it has started giving me problems like it shut downs when it is at low battery say just about to reach 10 %. No low battery message just complete shut down(bam, screen goes dark). Now I have done the following steps
    1. Battery has been calibrated it did solve the problem but it again started to happen.
    2. I got my laptop's fan replaced 28 days back on i guess Jan 5, 2015 and vents are clean
    3. I use Hardware Monitor Software to monitor the temperature and the results are as follows :
              >> During Normal Operations it remains between 50 to 55 C (is it Normal ?) What should be the ideal temperature ?
              >> Hard Disk temp is 60 to 64 C.
    4. I use battery saver mode and everything set to normal
    5. Drivers and BIOS Updated
    6. Used HP Support Assistant to check battery health it shows OK.
    7. I have changed the values also like I set the critical level,low battery and reserve battery but i guess that also not working.
    Now My Question is 
    1. Is it due to overheating ? During normal operations like when plugged in it doesn't shutdown. Works Perfectly.
    2. Or the battery is giving me trouble and needs to be replaced. After 100% charge it gives me around say 1 hr 30 mins of use but when it is about to hit  11 or 10% the system shuts down. 
    Please provide me with a solution
    P.S. I don't use my laptop for gaming

    Deep.
    Download and run BatteryMon.
    http://download.cnet.com/BatteryMon/3000-2094_4-29244.html
    After download click on start.
    In the upper left hand corner you will see a battery tab click on it to get the details of the battery.
    Look at Design Capacity,  Full Charge Capacity and Current Capacity.
    Let us know what you find.
    REO
    HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
    Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
    Microsoft Registered Refurbisher
    Registered Microsoft Partner
    Apple Certified Macintosh Technician Certification in progress.

  • 4530s probook shutdowns with no prior warning

    My laptop was running smoothly until recently it shut downs on its own with any warning or anything. i thought its happening because of over heting so i got it serviced and cleaned but its still doing the same thing. I think its related to its battery but the average time of the battery is good and it charges well too. i really cant understand whats wrong with it please help me. i have lost data too because of this problem.

    I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this HERE.
    HP ProBook 4530s Notebook PC Support
    TwoPointOh
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Just purchased Nikon D610. tried to import 3 images and got this message: The files are not recognized by the raw format support in Lightroom. How do I fix this frustrating problem. Have been using Lightroom for years also Nikon products without any prior

    How do I import images. Have a message that says: The files are not recognized by the raw format suppot in Lightroom. Am using a Mac version 10.9.4. the import is from a new Nikon D610. Am using LR 4.4 Please help Adobe is useless as a support.

    Each camera must be supported explicity and your LR version is years older than your camera.
    According to Adobe's Camera-support page, you need at least LR 5.3 to work with your D610 NEFs in LR:
    Camera Raw plug-in | Supported cameras
    If you don't want to upgrade to LR 5, or can't due to your OS being too old, then it might work to use the latest DNG Converter and create DNGs from your NEFs, which should open in LR 4.x.  You can find the DNG Converter here:  http://www.adobe.com/downloads/updates

  • Sound level variations without any command

    Hello.
    When using my iMac 24" 3,06 Ghz, the sound level always varies without any command.
    It is very disturbing mostly because it is associated with the display of the sound level on the top of the screen.
    Can you help me?
    :-) Dominique

    A little more background. I've now found that I can get my volume back by clicking the Device setting off of CoreAudio, and then selecting CoreAudio again. This lasts awhile then the sound drops out again. Also, I've tried different instruments in the EXPS 24, different Instrument/MIDI channels and still get the dropout prob. Even deleted the audio object in the environment and started over with a new one. All the other instruments in the track list are EXPS 24 and not affected

  • My laptop Shutdown without warning

    My new hp pavilion that I bout around october 2014'seem to be shutdown without warning. it shutdown with the shutdown window appear thou. it happen 3 times. please help

    Hi @timotius ,
    Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Notebook and having it shut down without warning. Here is a link to restore the BIOS. Please note remove any and all USB devices, and remove memory cards from the card reader slot. Disconnect all non-essential devices.
    Can get to safe mode with command prompt?  sfc /scannow would scan your system for errors at the command prompt. You could check this Microsoft document on system recovery options.
    Here is a link to the HP Support Assistant. Just download and run the application and it will help with the software and drivers on your system. If you needed an update this could cause what you have installed.
    Did you install any software or hardware?
    Hope this helps you.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Satellite A30 CDRW-DVDRW (Mat****a) drive can't recognize any dvd

    Hi!
    I own a Satellite A30-303 with a optical drive MAT****A UJ811 (CDRW-DVDRW).
    Everything worked just fine until last week the drive stopped reading any DVD. A error message saying that there is some problem with E/S is displayed. CDs are recognized with no problems though.
    I tried to find updated drivers for the DVD driver but I couldn't get any.
    Please does anyone have an idea of what that might be and how to solve it??
    Thank you!!
    Alex

    Hello
    On this way it is always not simply to say what the problem can be. Like littco wrote check if there is some virus or any kind of malware. It is also possible that there is some technical problem and the drive can not calibrate on the right way.
    I really dont know what you mean with E/S but you can try to remove the device from device manager and restart the unit. The last thing that you can try is to reinstall the unit using recovery CD. On this way the unit will be absolutely clean. If the problem persist there is obviously malfunction and the drive must be replaced.
    By the way; have the same opinion like littco.
    Bye

  • Turn off suddenly without any warning when plugin Adapter(Charger)

    My Pavillion dv6-3208tx turn off suddenly without any warning when plugin Adapter(Charger) and it won't start unless i unpluged the adapter. I can run on battery. Pliz help...!

    Make sure the keyboard is seated properly.
    (Instructions can be downloaded here.)
    Sometimes, plugging in the adapter when the keyboard is improperly seated can cause this behavior.

  • I always update my iPad without any problem , but this time for the iOS 7 , it is still downloading from yesterday more than 24 hours and as a result I can't open any email . So can you help me or tell me what went wrong

    I always update my iPad without any problem , but this time it didn't work out . My iPad 4 is still downloading from yesterday and I can not meanwhile open any website or any mail . Can you tell me what went wrong ??

    Try reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.

Maybe you are looking for