Satellite A30: Sound card & Chipset driver problem.

Hi all,
I'm about to get REALLY crazy!! I'd really appreciate if anyone can help me..
My story is:
I've lost all my recovery&driver CDs that were given to me in 2004 . But, I had to format my pc at this weekend due to many system reasons(bugs, unable to connect to net, etc).
My first step was I downloaded all kind of drivers for Satellite A30 from Toshiba site. And I got XP professional SP2 from my friend and installed it. But after finishing all the installations below is the result:
1) NO SOUND :(
2) Question marks on 2 items that are a)Multimedia Sound Controller and b)PCI Modem in Device Manager/Other Devices.
3) Chipset installation error message: Intel(R) Chipset installation utility requires chipset platform supported by the supporting operating system. Please read system requirements section in readme.txt for further info.
As far as I checked in forums my chipset was not properly installed, but, when I try yo install the Intel chipset 895PE (csutil-sa30-xp-5011015.zip) that I downloaded from download address http://eu.computers.toshiba-europe.com, it gives error message and some people tells to install drivers in a right order as, first install XP with SP1 and then install chipset utilitt, then install SP2 etc..But this seems to be not easy for me..
I can really repeat my FORMAT process again, but in which order..
thanks..

Hi,
Just to inform you that my problem was solved by itself :)
I've reformatted my laptop and installed the original XP Pro SP2 again by following the instructions.
Sound problem was solved automatically, no chipset utility installation required..
The sound problem was probably caused due to missing Microsoft KB835221 update for SP1, and KB888111 for SP2, which then was solved with the original latest XP..
Rgrds..

Similar Messages

Premiere Pro 2.0 and Windows 7 - Direct Sound Input soundcard driver problem

My XP machine crashed, I reinstalled Premiere Pro 2.0 with Windows 7, and I got the following error: 'The Currently installed soundcard driver does not support Direct Sound Input. Recording audio is not possible.' The soundcard drivers are updated. Any ideas? Here's what I have: AMD Phenom II X4 965 Processor 3.40 GHz 8 GB, 64 bit. Thank you for looking.

Thanks! Though I upgraded to solve the problem, this is good to know.
Bob
Date: Wed, 9 Nov 2011 04:45:42 -0700
From: [email protected]
To: [email protected]
Subject: Premiere Pro 2.0 and Windows 7 - Direct Sound Input soundcard driver problem
Re: Premiere Pro 2.0 and Windows 7 - Direct Sound Input soundcard driver problem created by Steve-Italy in Premiere Pro CS4 & Earlier - View the full discussion
VERY VERY VERY EASY (now, when I solved the problem, not before...!!!)
Insert Micropone or any jack in Micropone Input or Aux Input, on your sound card or motherboard !
AND NOW YOU CAN USE PREMIERE PRO 2.0
Enjoy
Steve - Italy
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4015730#4015730
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4015730#4015730. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Premiere Pro CS4 & Earlier by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

I want to Connect my Mac Mini as a Slave to a Mac pro Server while at the same time using the Mac mini's thunderbolt ports peripherals ( ie monitor, Sound Card, Hard drives) Creating a poor man's new mac Pro. Can this be Done?

I want to Connect my Mac Mini as a Slave to a Mac pro Server while at the same time using the Mac mini's thunderbolt ports peripherals ( ie monitor, Sound Card, Hard drives) Creating a poor man's new mac Pro. Can this be Done?

Well, I really would love the new unreleased mac pro however , I'm not sure of the expected cost , Everyone speculates from $3,000 to $8,000, in which I may have to wait a while to purchase.
To the point .... I want fully functional thunderbolt ports to be on the current mac pro's .... wonder if anyone had workarounds yet?... or could I chain the the current mac pro to a mac mini to make that happen?

Satellite C850D-11C PSCC2E - CHIPSET driver for Win 7 64bit needed

Hi,
I've been stuck in a long convo over at the techsupportforum and was finally told to try here.
So, I own a Satellite C850D-11C PSCC2E with Windows 7 x64.
I can't seem to find the chipset driver for my laptop in the list of drivers.
I first tried to install all available drivers, but it's obvious without a chipset I will have problems, and I do.
The USB ports don't work like they should etc.
Where is the chipset driver for the C850D-11C PSCC2E?
Thanks!

Hi
Your notebook is equipped with an Ati (AMD) graphic chip.
This means that the chipset must be from AMD too.
According to some information which i found in internet, the AMD A68M Chipset should be built in the notebook.
Furthermore as far as I know the ATI chipset driver is part of the ATI/AMD graphic card driver and therefore you should install the GPU driver to get the chipset driver installed

Intel 9 series chipset driver problem

hello
i know this is intel driver's problem, but as a manufacturer who use intel products especially chipset, can anyone tell intel that their "9 series" chipset driver is totally crap, absurd and so on? for those who are using this series of chipset, try checking their chipset driver via device manager and click any of "intel 9 series chipset family" driver under system devices or "intel 9 series chipset family usb..." driver under usb controllers and you can find that its driver provider are from microsoft and dated 2006. right, it is installed by operating system and chipset installer utility did nothing.
until intel knows about this thinsg, those who using 9 series chipset are using drivers from microsoft.

Hi,
Do you actually have any problems? Because Quote
chipset driver is totally crap, absurd and so on?
doesn't explain anything.
Follow >>Posting Guide<< and if possible we'll help you with the problem.
The fact they're dated 2006 doesn't mean anything. As long as thing is working fine, there's no need of updating. Possibly you're one out of xxx people that has some problems with it, but Intel (nor MSI, M$ and so on) couldn't really catch the issue since millions of tests before release is impossible.

Video card or driver problems with an N200, please help!

I have a lenovo 3000 N200, it is really cool, runs even games quite well, including newer ones.
But, is it normal to for the display driver program to freeze out in Warcraft 3? It always does that, when accessing the list of maps in the game and after 3-5 mins during an actual game. It sets the resolution down to 640X480 (from 1280X800) and in 16 color. I have to reset it in order to make it work. Also it does the same in Spore - though after having the driver written for Spore installed, ( which I downloaded from lenovo's site ) I haven't encountered that problem so far. Also Second Life shuts down - thankfully it does not freeze the drivers. I understand that the model I have is not meant for gaming but if it can run Warhammer 40k: Soulstorm at meduim graphic settings (on widescreen) without a lagg I can't understand why it wouldn't be able to handle warcraft 3 - that even an ATi m200 express can handle. I mean an X3100 from Intel must be far more powerful. (Said ATi card laggs with older games like Unreal Tournament)
I have the latest driver - official - and a Win Xp pro Sp2. I always keep my system up to date - save for opsys but so far driver did not need sp3 - and virus clean.
Please help me?
Solved!
Go to Solution.

Well, Unreal Tournament 2004 runs flawlessly on max graphics - though simple Unreal Tournament laggs like hell with all possible settings - also, as I said Dawn Of War and it's expansions run well on med graphics. The Suffering Ties That Bind runs also good on highest settings - though there is a bit of degradation compared to my tabletop pc's performance. Disciples 2 ran - of course - well, there were some texture problems with it but Heroes 5 ran quite well even on higher settings (as I mentioned it sometimes blunted down the textures but not always and it ran without a lagg). Alien Versus Predator 2 ran on max graphics, and there was no trouble, save for the aliens' special vision (that white thing that looks as if inverted colors) didn't work - aka was only a black screen - and that the crosshair of the smartgun was only a blank red/green block on the middle of the screen.Oh, and Command & Conquer: Generals Zero Hour works on highest settings without a lagg, along with Quake 3, and Jedi knight : Academy. It even runs Perfect World on high settings and only laggs in bigger towns - but that also might be because of the tremendous bandwidth usage that occurs. Even Red Alert 3 was able to run, but I would only advise that for RA fanatics, on low settings it was playable. Also, C & C: Tiberium Wars runs better than RA 3 , if you like that it is quite playable and worth a try. As you can see I have put it to it's limits to see what it can endure. Unreal Tournament 3 ran, though was gruesomely degraded and then it gave me the blue screen of death; so I quickly uninstalled that. Other than the forementioned program I had no real problems with the card, but the existing problems are a pain in the ... well we all know how bothering it can be when one is unable to play his/her favourite game (that should really run flawlessly).
Doesn't vista eat up too much of the system resources? A friend of mine was complaining about his n200 that vista is too slow on it and it eats up too much processor/memory.
Also, still no new on videocard front... Asked around if anyone knows, but I am guessing that maybe even Blizzard - referring to my Warcraft problem - shows more compassion to their forums and users than Lenovo, so I'll ask around there too.

Satellite A30 hibernation and turning on problems

hi
i have had my toshiba sattelite A30 laptop for 14 months now, and havent had any major problems until now. whenever i turn my laptop off or put it into hibernation, it wont restart normally the next time i use it, it just acts as if it is starting, then stops and turns itself off, and will do this over and over until i remove the power cable and take out the battery, then put it back in and restart, and then it just acts normally.
i have checked and deleted all viruses on my hard drive, but this problem is worrying me.
does anyone have any idea why this is happening?
thanks

Hi,
did you tried to reinstall the Toshiba Power Saver yet?
A friend of mine had also hibernation problems and he reinstalled the power saver!
We dicussed about it and it can be that the hibernation file is damaged and have to be generated new!
Bye chris

New install on new mobo (nVidia chipset): driver problem

I've just installed Arch on my new PC but, for some reason, it doesn't seem to be recognising the hardware, viz. the nVidia MCP67 chipset. Here's the lspci:
00:00.0 RAM memory: nVidia Corporation Unknown device 0547 (rev a2)
00:01.0 ISA bridge: nVidia Corporation Unknown device 0548 (rev a2)
00:01.1 SMBus: nVidia Corporation Unknown device 0542 (rev a2)
00:01.3 Co-processor: nVidia Corporation Unknown device 0543 (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1)
00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
00:08.0 PCI bridge: nVidia Corporation Unknown device 0561 (rev a2)
00:09.0 IDE interface: nVidia Corporation Unknown device 0550 (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation Unknown device 054c (rev a2)
00:0b.0 PCI bridge: nVidia Corporation Unknown device 0562 (rev a2)
00:0c.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:0d.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:0e.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:0f.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:10.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:11.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
02:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7900 GS] (rev a1)
03:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet Controller (Copper) (rev 06)
And here's the lspci from my ubuntu install:
00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.3 Co-processor: nVidia Corporation MCP67 Co-processor (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1)
00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2)
00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2)
00:0b.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0e.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0f.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:10.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:11.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
02:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7900 GS] (rev a1)
03:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet Controller (Copper) (rev 06)
Can anyone tell me what module I need to load (configure MODULES= in rc.conf) to get it working?
btw, here's the MODULES= stuff from my current rc.conf:
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(e1000e forcedeth slhc snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
Last edited by Shagbag (2008-09-16 17:10:25)

It boots Ubuntu fine. Arch linux doesn't complain either. I only found out about the problem when I tried to pacman -Syu straight after the install - there was no networking. ifconfig had done its job but there was no routing table. I manually added route add default gw 192.168.0.1 and edited /etc/resolv.conf to make sure I could get to my router but, again, it wouldn't work. The forcedeth module had been loaded (ethernet driver) so I took a look at lspci (details in very first post) and can see that it's appears to be an issue with the PCI bus (the ethernet hangs off the PCI bus)I ran hwdetect --modules and pasted the output into /etc/rc.conf and rebooted. Still no joy.
The mobo is an ASRock 939N68PV-GLAN. It has an nVidia chipset (GeForce 7050 NB + nForce 630A MCP SB). From my lspci results it would appear the problem is with the 630A MCP. As Ubuntu works and Arch doesn't I'm perplexed. And yes I've googled and followed what little help there is around. Nothing has worked so far. Hopefully someone will have experienced a problem with either the same mobo or the 630A MCP and they can tell me what needs to be done.
Last edited by Shagbag (2008-09-19 08:50:21)

Intel Chipset Driver Problem

I have the following problems when installing bootcamp driver 3.1 to newest Macbook pro 15' i7 core,
Intel(R)Series/3400 Series Chipset Family USB Universal Host Controller - 3B36 has a driver prblem
Intel(R)Series/3400 Series Chipset Family USB Universal Host Controller - 3B3B has a driver prblem
What are these controllers?

In order to promote a solution, I filed a bug report at
http://developer.apple.com/bugreporter/
I assume that Apple has to resolve this problem with a firmware update, because it seems to be independent from the chipset drivers being used. I could reproduce the problem on different Windows versions, including Windows XP Professional SP3 32-bit and Windows 7 Ultimate 64-bit.
It is possible for me to use the USB ports to a certain degree (i.e. external media like hard drives or memory sticks), until the system becomes completely unresponsive. By using a remote session I could verify that the system was still running, but that all USB devices including keyboard, trackpad and mouse lost the connection to the system.

PCI Sound Card Problems in MEGA PC

Added a new Sound Blaster Live 5.1 card in my PCI slot. I use a special audio program that creates 2 stereo outputs from that card.
I've had this card in my older PC and it works fine. When installed in MEGA PC PCI Slot one of the outputs has a low volume and the other is normal. Why?
I tried to use the stereo outs of the integrated sound card with my programand got the same problem. One stereo out has a much lower volume than the other.
I using Win 98SE/and Sound Blaster Live 5.1. I hope I can get some help or I plan on returning this unit to my local retailer.

Thanks for responding. I did try disabling the onboard sound via the BIOS. No change to the problem.
Even the onboard sound card has this problem when trying to use 2 stereo outs. I found I could balance the outputs by using the AV Rack application. You use it to control the volumes on each output channel. The problem is I can only decrease th louder channel's volume I can't increase the volume on the other and this is what I need to do.

Sound input plot update problem

Hi,
I am having some problem regarding the plot of the sound input signal. Specifically the problem is regarding the update of the waveform graph i have used.
the update is not continuous mode. And there are gap in the waveform
can anyone help me
Attachments:
Continuous Sound Input.vi ‏20 KB

Thanks! Though I upgraded to solve the problem, this is good to know.
Bob
Date: Wed, 9 Nov 2011 04:45:42 -0700
From: [email protected]
To: [email protected]
Subject: Premiere Pro 2.0 and Windows 7 - Direct Sound Input soundcard driver problem
Re: Premiere Pro 2.0 and Windows 7 - Direct Sound Input soundcard driver problem created by Steve-Italy in Premiere Pro CS4 & Earlier - View the full discussion
VERY VERY VERY EASY (now, when I solved the problem, not before...!!!)
Insert Micropone or any jack in Micropone Input or Aux Input, on your sound card or motherboard !
AND NOW YOU CAN USE PREMIERE PRO 2.0
Enjoy
Steve - Italy
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4015730#4015730
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4015730#4015730. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Premiere Pro CS4 & Earlier by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

Sound Card on Hp Pavilion dv7-1175 Notebook

My microphone seems to have alot of static when I talk, so I did some further researching and some people think that it may be the sound card thats the problem. The mic is brand new and i've tried other mic's with this machine and its the same problem.

Hello,
Are you still having the issue? Have you done any troublshooting becides a reinstall of the driver? When you reinstalled the driver did you use Recovery Manager or HP.com?
When you respond I will recieve an e-mail. Let us know!
I am an HP employee.
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.

Multichannel sound card setup

Hey!
I am trying to, in some way, enable multichannel output from my sound cards as a part of the default audio output from my MacBook Pro.
The main goal is to use four of the total 10 outputs i have available.
At the moment i have this hardware:
Usb sound card: Native instruments Core 1. 2 outputs, 2 inputs
Usb sound card: DAC driver, 2 outputs. These are actually a pair of Argon speakers which do have a USB input.
FireWire: Infrasonic Deux 0448. 4 outputs, 2 inputs.
Speakers:
Pair of Yamaha HS-50
Argon Speakers(not sure of model, it really does not matter)
Both of the speaker do have analog inputs.
I have merged all of these sound cards in all different constellations but I am still not able to make my macbook output audio in 4 channels as default. My main idea is to make the speakers work like a pair of stereo speakers. So I have one Yamaha speaker on top of an Argon speaker and they both play the same sound. So what I am really looking for is, not to merge two sound cards but, to merge output channels.
For example i want to deliver the same "left pan" audio to the hardware output on the Deux soundcard, say channel 1 and 3 is the left ones and 2 and 4 are the right ones. The problem is this: I only get audio from 1,2 or 3,4 not all four at the same time.
The Sound/Midi settings does not allow me to use quadraphonic output as a tool of delivering sound to all of the speakers. I don't understand this, is the quadraphonic setup only for quadraphonic designed sound only? Cause what i really do need is two pairs of stereo outputs, software wise.
Does anyone know how I can overcome this problem?
Any answers that can help me with this are welcome!
My MacBook Specs:
MacbookPro late 2011
Processor 2,2 GHz Intel Core i7
Memory 8 GB 1333 MHz DDR3
OS X 10.9.5

OK, that link did help some. KDE isn't giving the error any more, but sound still isn't working, sort of.
I tried mpg321 and xmms on one of my mp3 files that I know works fine, both report that they are playing the file, but nothing comes out of the speakers. Yes, I've checked the volume on the speakers, they work fine in windows and redhat.
Info Center shows Sound Driver:3.8.1 a-980706 (ALSA v0.9 Orc3 emulation code)
My rc.local looks like:
modprobe snd-cs4236
modprobe snd-cs4236-lib
modprobe snd-pcm-oss
chown sasdav.users /dev/sound/*
And my modules.conf has:
alias sound-slot-0 snd-cs4236
alias eth0 3c59x
Obviously I'm missing something, any clue what it might be?

Stream audio from sound card input thru network

Good Day:
I have an application where I need to access instruments at a remote location. Command/Control of the instruments is not a problem, but I also need to stream the audio present at the remote system's sound card thru the network connection. Any suggestions on how to accomplish this via LabWindows?
Thanks in advance for any replies.
-Ed

Hi Ed,
First, I was wondering, how do you get the audio from the sound card? Is it from a LabWindows program? I've never done that. Second, I was wondering how do you play the audio on the remote machine? Is that through a LabWindows program? I've never done that either.
But I was wondering if just a remote PC app would do the job. Like admins use to take over your PC from there desk and fix problems. I assume they have these that send the audio thru the net as well as the screen. Then on the radio's PC you just need a LabWindows program to control the radio and some other app to play sound from the sound card input to the local speaker. Then the remote PC app would magically transfer the screen and audio from the radio PC to the remote PC.
Otherwise, I can just say that to stream the audio thru the net, after the Radio's PC gets it off the sound card somehow, I would just set up two TCP servers on the remote PC, one for audio and one for the commands/control. When the remote PC client connects to the audio server the audio server would just start sending audio data to the client. The client would receive the data and put it in a big buffer to handle network speed variation. Let the buffer fill up to like a second or more worth of data before having anothe function/thread read the buffer data and give the data to the client PC's sound card. Big problem is that the client PC's sound card will alway's consume the data at a slightly different speed than the servers sound card produces it. Different clocks running at slightly different frequencies. So the client function that reads the audio buffer to give it to the sound card must play games. If the buffer is shrinking over time then it has to create extra samples to give to the sound card, just duplicating a sample every 100 samples or whatever. If the buffer is growing over time then it throws away a sample every 100 sample or whatever. So it's kind of a challenge to manage the buffer with the variable speed of the net transfering data and the two different rates of producing and consuming the audio data.
LabWindows has the TCP server create and client create functions so that's pretty easy. The harder part is that you probibly want to set the Radio's PC to a fixed IP address so that you can connect to it without worrying about domain names and such. Then the two TCP ports that the LabWindows uses for command and audio might need to be setup in all the routers to let you establish a connection. Your IT guy's can answer that.
PS. you can play around with this suff on one PC by using the RegisterTCPServerEx function and setting the local host address to "localhost", or "127.0.0.1" on one LabWindows project and using the corresponding ConnectToTCpServerEx with "NULL" as the server host name on another LabWindows project. This creates a virtual TCP connection on the same machine. This does not duplicate the different audio clock issue I talked about above.

Video card error - No resources when sound card installed.

Hi
I hope that someone can help me here :/
I just bought a x-fi Sound Blaster card... I installed it and booted up PC.. When windows loads the screen and colours are at their minimum.. I look in device manager and there is a yellow warning icon on the device (GeForce 6800 Ultra).. It says, unable to find enough resources, please disable another device in the system.. I disable the sound card and re-boot..no change.. I tried to go on the internet but the browser kept crashing.. I took the sound card out of the PC and everything is fine now.
Has anyone come across this before? I'd appreciate any help on this
Thanks
JonSince it's the sound card causing the problem, I thought it'd be ok to post here

Hi?Thanks for the replies... I've tried 4 PCI slots with no luck.. My AGP was already set to 256 ?One thing that I did notice was that after installing the SB software.. The test signal would only come through the left speaker... The speakers work fine with the on-board sound (which has been disabled btw).. I checked the settings and everything seemed as it should be...So this is either to do with the conflict or it's a faulty sound card.. IRQ's are a tricky subject for me.. There are lots of settings in the bios..Everything is set to auto currently. With the Sound Card out, the graphic card takes IRQ 6 (as told by device manager) in the bios it says it's assigned IRQ .. When the SB was installed, I forget what IRQ it had but I'm sure it was neither or 6.. Thanks for any further suggestions?Jon

Satellite A30: Sound card & Chipset driver problem.

Similar Messages

Maybe you are looking for