Satellite A300-15K: Polish character does not appear using shortcut key

Hi,
I am a fresh user of A300-15K and from the start I have discovered that it has combination of Alt+Ctr+C assigned to starting up ATI software (Catalyst Control Centre). Unfortunatelly this combination normally should produce Polish character "?" ( it doesn't look properly on this page somehow after I have copied it from Word - it is "c" with stong accent over it - here is its capital version "?").
I entered Catalyst Control Centre and unmarked the use of so called HotKeys (first this particular hotkey and then the use of hotkeys generally), but all I achieved was that Catalyst Control Centre stopped starting up after the combination usage.
However, the needed Polish character did not appear. I can get its capital version with Alt+Ctr+Shift+c, but no normal version.
A guy from service centre advised me to assign a different letter as startup combination for Catalyst Control Centre and I did, but it still did not make the Polish character appear.
I guess there must be a fault in regional settings so I tried to change them to English and back to Polish with zero result.
Please help with some word of advise.
Message was edited by: Koster62

Its easy to turn off.
Just enter the catalyst driver and there must be option like 'shortcut'. Turn it off.
I had the same problem.
I remember only it was really easy to turn off.
You shouldn't have problem with that.

Similar Messages

  • Field on manual tabular appears using Firefox but does not appear using IE

    Hello,
    A field in a manual tabular form appears correctly using Firefox but does not appear or appears in another field when IE is used. Javascript is used to hide certain columns on the tabular form. Does anyone know how to solve this problem?
    Thanks pany

    Prabodh,
    The select for the report and the javascript that is used to hide the columns are displayed below. The data for Apex_item.select_list_from_lov(12,null,'LOV_METHOD_OF_ACQ') is shown in the previous column, Date Acquired, and the column for Method Acquired is blank. It appears correctly in Firefox. Please let me know if this is sufficient.
    Thanks,
    pany
    SELECT
    apex_item.hidden(1, c011) status
    ,apex_item.checkbox(2,seq_id) checkbox
    ,apex_item.hidden(3, seq_id) seq_id
    ,apex_item.hidden(4,c001) Owner_Firm_Id
    ,apex_item.hidden(5,c002) Owner_Id
    ,apex_item.hidden(6,c003,10) First_Name
    ,apex_item.hidden(7,c004,10) Last_Name
    ,apex_item.text(8,c005,10) Number_Shares
    ,apex_item.text(9,c006,10) Percentage
    ,apex_item.text(10,c007,10) Class
    ,apex_item.date_popup(11,rownum, c008, 'MM/DD/YYYY',15) Date_Acquired
    ,apex_item.select_list_from_lov(12,c009,'LOV_METHOD_OF_ACQ') Method_Acquired
    ,apex_item.hidden(13,c010,10) Primary_Key
    FROM apex_collections
    WHERE collection_name= 'INTEREST_STOCK_COLL'
    AND c011 IN ('O','N','U')
    union all
    select
    apex_item.hidden (1,null) status
    ,apex_item.checkbox(2, null) checkbox
    ,apex_item.hidden(3, null) seqid
    ,apex_item.hidden(4,null,10) Owner_Firm_Id
    ,apex_item.hidden(5,null,10) Owner_Id
    ,apex_item.hidden(6,null,10) First_Name
    ,apex_item.hidden(7,null,10) Last_Name
    ,apex_item.text(8,null,10) Number_Shares
    ,apex_item.text(9,null,10) Percentage
    ,apex_item.text(10,null,10) Class
    ,apex_item.date_popup(11,1, null,'MM/DD/YYYY',15) Date_Acquired
    ,apex_item.select_list_from_lov(12,null,'LOV_METHOD_OF_ACQ') Method_Acquired
    ,apex_item.hidden(13,null,10) Primary_Key
    FROM dual
    Javascript
    function hideCols(p_startOfTable, p_pageList, p_debug)
              alert("in function");
              var outStr = "Blanking Script:\n";
    var debug = p_debug;
    var offCols = p_pageList.split(":"); //string comes in colon delimited, split it
    into array
    var tbl = document.getElementById(p_startOfTable); //get the table from the page
    html source
    var rows = tbl.getElementsByTagName('tr'); //get the first row
    var tds = tbl.getElementsByTagName('td');
    var testStr;
    outStr = outStr + "START tds length is " + tds.length + "\n";
    if (debug)
    alert(outStr);
              //START Clear Headers
    var i, j, cells;
    cells = rows[0].getElementsByTagName('th'); //get the headers
    for (j = 0; j < offCols.length; j++)
    cells[j].className = "hidden";
    outStr = outStr + "i is " + i + " HEADER rows.length is " + rows.length +
    "\n";
    if (debug)
    alert(outStr);
    //END Clear Headers
              //START Clear TDs
              for (i = 0; i < tds.length; i++)
    var attrib = tds.innerHTML;
    var gNum = attrib.indexOf(" name=") + 7;
    var colNum = attrib.substr(gNum, 2);
    colNum = parseFloat(colNum);
    for (j = 0; j < offCols.length; j++)
    if (debug)
    testStr = testStr + "\n" + "colNum is: " + colNum + " className is: " +
    tds[i].className + " i is: " + i + " j is: " + j + "\n";
    if (colNum == offCols[j])
    if (debug)
    alert("colNum is " + colNum);
    if (tds[i].className == "datepicker")
    if (debug)
    alert("caught condition with i= " + i);
    tds[i - 1].className = "hidden";
    tds[i].className = "hidden";
    tds[i + 1].className = "hidden";
    //add popupLOV functionality here
    //add radio button functionality here
    // add other items that may have multiple <td>
    else
    //regular hideCol
    tds[i].className = "hidden";
              //END Clear TDs
    if (debug)
    alert(testStr);
    //document.write(testStr);
    Edited by: PANY on Aug 12, 2010 8:25 AM

  • Satellite A300-1IA - FN utlility does not pop-up on both XP and Vista

    I've got an A300-1ia, and since a week most of the FN function keys won't work anymore.
    The utility does not pop-up anymore in XP and Vista.
    I have a multiboot system and the problem did apear a week ago.
    I think it has to do with some windows update.

    It worked. I uninstalled the vap package and installed 1.1.14 because 1.1.19 didn't worked.
    He sended the message "getprofstring is failed"
    Tnx for suporrting gave you the points

  • Satellite A300-1EH - windows installer does not works accurately

    Hello, this is my first post on this forum!
    My windows installer does not works accurately.
    What to do?
    Soryy but i dont now much about computer systems.
    Have I to reinstall this installer?
    I'm waiting for your replys.

    >My windows installer does not works accurately.
    What do you mean exactly? Do you see some error? What happen exactly?
    Maybe your CD is scratched or damaged.

  • Audio track does not appear using Automate To Sequence

    When I use the Automate to Sequence feature after arranging clips in a Bin, none of the associated audio files show up in Audio 1 but the video clips do show up in Video 1. When I do this on other computers it works fine. (This is a classroom setting.)

    Start reading on mono and stereo tracks and project setup.

  • Re: Recovey menu does not appear on my Satellite L500-19X

    Hello,
    I cant start my toshiba laptop L500-19X.
    When I start appear two option menu. 1.Start normally or 2. Recovery mode. Both options cant run windows 7. I only obtain black window without seeing any windows.
    I try pressing F8 to enter the detailed recovery menu. I select the Repair Computer option waiting for the Toshiba Recovery Options Menu but it does not appear. The only thing appears in the screen is the mouse pointer in minor resolution mode, but i cant see the menu, and this stills forever.
    What can I do?
    Thanks.

    After I press Repair You Computer in the F8 menu, the next screen shows a progress bar with the message: "windows esta cargando archivos..." (windows is loading files). When the progress bar finish appears a few seconds a new screen where I can see a symbol as if w7 is loading, but 2..3 seconds after goes to a black screen. And more seconds after, even minutes, appear the mouse cursor, but after it happens nothing, and I dont listen hdd work forever.
    Thanks.

  • The site icon does not appear in Firefox

    I am developing a site (http://www.londonglamourphotoshoot.co.uk/index.html) but the site icon (the little icon that appears next to the site title in the tab label) does not appear in Firefox. It appears in Internet Explorer and Chrome, but for some reason, Firefox ignores it while it shows the icons of other sites perfectly.
    If I show the source code of the page and then click in the hiperlink of the icon, then the icon loads as an image, so it is the correct link (and as I said, IE and Chrome display it)
    Here is the line Muse generates:
    <link rel="shortcut icon" href="images/favicon.ico?4188924898"/>
    (I don't know the reason of the question mark and the number after the icon URL, but this is as Muse writes it)
    I load the icon in the properties window of the master page only so it is inherited by all other pages of the site.

    I doubt it. The filename of the original file is just favicon.png and it was loaded in the generic site properties (not in a master page or in the individual pages). The question mark and number are part of the code generation process by Muse. What's more, Windows would not allow me to name a file with a question mark, it is a forbidden character, but in an URL it means additional arguments or something like that if I'm not mistaken. .

  • LabVIEW serial command does not appear to complete until I open a Hyperterm.

    I can command my device using hyperterm. However, the LabIEW command does not appear to complete. I issue the command in LabVIEW and then open the hyperterm to verify the command was recevied (status query). When I start the hyperterm session (with a carriage return), I get a response from the device stating that it is performing the requested action, and then (after 1-2s) a response stating that the action has completed. I have tried commanding using both the VISA protocol and the basic serial I/O. I have also tried , and as my termination character in LabVIEW.

    But are you explicitly sending the termination character from LabVIEW? Just setting the termchar applies only to read operations, not writes.
    If you want VISA to send the termchar for you on write operations, set the property "ASRL End Out" to "TermChar".
    And if you are appending the termchar manually to the strings you send, make sure your LabVIEW strings have the backslash codes view turned on so you're actually sending the right code (instead of sending an actual backslash code itself across the serial cable).
    Dan Mondrik
    National Instruments

  • Ruby (Furigana) does not appear

    Problem:
    Ruby does not appear above kanji.
    Question:
    What settings might I need to change to get ruby to appear above the selected character?
    Screenprint:

    Hi Peter.
    Your questions led me to the right setting.
    Yes, I have the Japanese version of ID installed (in the same location as the English as far as I know).
    The World Ready Composer was turned off. I turned it on and no changes occurred, but beneath that command is the Japanese Paragraph Composer.
    When I turned the Japanese Paragraph Composer on, the ruby text (small characters that appear above the kanji) appeared as in the screenshot provided below:
    This is solved.
    Thank you.

  • EWA Session does not appear

    Hi all,
    I've installed SolMan 7.0 EHP1 and complete the initial and basic configuration using SOLMAN_SETUP tcode.
    Then I connect a satellite system with SMSY tcode and setup the EWA configuration.
    Now I want to create a EWA Report manually but when I run the REFRESH_SESSION from SDCCN tcode on satellite system the EarlyWatch Alert for Solution Manager Session does not appear.
    Could you please help me?
    Thanks in advanced
    Moreno

    1. Did you setuo EWA in SOLMAN for that satelitte System? DSWP->Select the solution->Operations Setup->Solution Monitoring->Early Watch Alert->Setup Early Watch Alert.
    2. If you have done this, then goto DSWP->Select the solution->Operations->Solution Monitoring->Early Watch Alert->Just click on the scheduled EWA. It will tell you why the session data is not collected from satelitte system though you ran REFRESH_SESSION at satelitte system.
    OR
    3. Check whether EWA is active at solman for that solution(Satelitte System).
    DSWP->Settings->Solution Monitoring->Early Watch Alert
    4. Check maintenace package and EWA is scheduled after you ran REFRESH_SESSION at satellite system(SDCCN), if so, then select the maintance package->click on details button(right side of the screen). Make sure that "Target RFC Destination" under Target System should be Back RFC of Solution Manager.
    Hope this may help you.
    Regards
    Sanjai

  • My Laptop Model (L505-SP6984R) does not appear in Toshiba Site

    I just bought a Satellite L505-SP6984R and wanted to subscriber to Toshiba Updates, but the laptop model does not appear in any of their lists. Does anyone have a recommendation of which model to choose instead (if any)? The model do appears when I provide the part number and serial but that's on another part of the site that is not related to support.

    That's probably why you can't find it here in the United States support site.  Try the Latin American site http://www.toshibalatino.com/  I don't speak spanish so I can't search for it there for you.
    If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.

  • Airport time capsule does not appear within wi-fi networks on my OSX neither on my IOS devices, even though the backup for my OSX is on progress. why it does not appear?

    Airport time capsule does not appear within wi-fi networks on my OSX neither on my IOS devices, even though the backup for my OSX is on progress. why it does not appear?
    Is it because the backup on progress?

    Hmmm.. ok.. well you are kind of on your own.. purchasing from another country leads to problems.. especially as the TC itself is regional .. all the setup applies to the region it is sold in.
    Make sure you are using ipv6 in the computers..
    See
    http://support.apple.com/kb/TS4597
    The 6.3 utility will not work without it.
    Make sure all names are short, no spaces and pure alphanumeric.
    Do a full reset and start over.
    But there are no more controls.. you cannot set mode..
    You can set wireless channels.. so do .. try different wireless names for the different bands.. and set fixed channels.. whatever your country allows, usually 2.4ghz you can use 1, 6, 11 but 13 maybe an option as well. 5ghz is much less clear and there are more variation. Just set to one channel and then another.
    Set WPA2 Personal security with a 10-20 character password .. pure alphanumeric mix of upper and lower case and numbers.

  • I am trying to set up Sharing amongst several computers on my home network.  I have followed all the setup instructions but after completion Sharing does not appear in my iTunes window (on any of the computers I've set up).  There is no explanation why.

    I have been trying to set up Sharing between two computers on my network. I did this once and it worked.  However, when I try to set this up now the Sharing feature does not appear on the left side of the iTunes window (on either computer).  There is no explanation as to why not.  Is this a configuration problem, a network problem or what?   Can it be fixed?  I have tried turning sharing off and back on on both computers but to no avail.  What am I missing?  Thanks for any help you can provide.

    Hey innerev2003,
    Thanks for the question, and welcome to Apple Support Communities.
    If, while searching through your past purchases, items are unavailable to download and show a "Purchased" button, they are still on your computer. It may be best to search your iTunes library by clicking Music, then use the search bar at the top right.
    If you are completely sure the items are no longer in your library, try signing out of the iTunes Store, and then back in.
    iTunes 11 for Windows: Manage your iTunes Store account
    http://support.apple.com/kb/PH12507
    Thanks,
    Matt M.

  • Hi all, I upgraded my MBP to Lion , but on the screen where i need to type my password, click  on my photo and it does not appear the place for me to type my password and it stay stuck there. Can anyone solve this problem for me?

    Hi all, I upgraded my MBP to Lion , but on the screen where i need to type my password, click  on my photo and it does not appear the place for me to type my password and it stay stuck there. Can anyone solve this problem for me?

    Reboot the machine holding Command and r keys down, you'll boot into Lion Recovery Partition
    In there will be Disk Utility, use that to select your Lion OS X Partition and Repair Permissions.
    After that is done reboot the machine and see if you can log in.
    If not repeat the above steps to get into Lion Recovery, get online and reinstall Lion again, it will overwrite the installed version and hopefully after that it wil work.
    Reboot and try again.
    If not follow my steps to create a Snow Leopard Data Recovery drive, then option boot from it and grab a copy of your files off the machine.
    Then reinstall all your programs onto the external drive like setting up a new machine, then use Disk Utility to erase the entire internal boot drive (select the drive media on the far left, not the partiton slightly indented) format Option: GUID , 1 partition OS X Extended and then use Carbon Copy Cloner to clone the external to the newly formatted internal drive. Once that is finished reboot and disconnect the external drive.
    Once you go that, boot into Snow Leopard and update to 10.6.8, use the AppStore and option click on Purchases and download Lion again and install.
    Lots of work, but there is no Lion disks.
    https://discussions.apple.com/message/16276201#16276201

  • BPM Application Link does not appear in BPM Workspace (11.1.1.7)

    I spent huge amount of time to reveal why does that happens.
    All that follows further is valid for BPM Suite 11.1.1.7.
    The scenario.
    You developed a simple BPM process with Initiator pattern (maybe by following the "Quote Request" tutorial).
    But the application link did not appear in BPM Workspace.
    Here i'm skipping any kind of mistakes as "oh, incorrect swimlane", "oh, i did not include the user to the app role" and so on.
    At first, you should know about the "feature" - You have to attach task form to the Initiator Human Task to see the App Link.
    The simplest way to do that is to AutoGenerate task form (and deploy it, of course).
    Else the Appication Link will not appear.
    One exception to this rule - If your Task HAS NO PAYLOAD (no parameters) the Task Form is not required (to appearing of the Application Link).
    The second find is a bug (is think so).
    If you edited the Role that Attached to the swimlane of Initiator Task, you will not see the Application Link.
    If you look to organization.xml you will see something like this:
            <ns1:applicationRole id="StartTask.InitRole" isProcessRole="true">
                <ns5:name>StartTask.InitRole1</ns5:name>
                <ns1:processRole id="InitRole" name="InitRole1"/>
            </ns1:applicationRole>
    The Application Link will appear ONLY IF THE "applicationRole id", "applicationRole name" and "processRole id" have the same value.
    When you edit name of the application role in Organization Editor you change "applicationRole name" and "processRole name" values.
    After that "applicationRole id" != "applicationRole name" and the Link does not appear.
    How to fix?
    Just edit organization.xml (with external editor) - change the "applicationRole name" to the value of "applicationRole id".
    That allows to have value of "processRole name" something like "The Initiator Role" - that value appears in the BPMN diagram of process.
    Also you can edit organization.xml with Organization Editor and set the Name to the value of "applicationRole id".
    In that case the associated swimlane will have the same name as the "applicationRole id".
    Hope this helps somebody
    Oleg

    Flash Player is a browser add-on, not an executable program.
    If you need to open a local SWF file you will need the standalone player (Projector) from http://www.adobe.com/support/flashplayer/downloads.html
    Note that the download is the player, not an installer, so you will need to make the file association manually.

Maybe you are looking for