Satellite A300-1AK don't start after update Win Vista

Hello everyone, hope someone can help me
I have a toshiba notebook with a view, I got the bright idea to do an update since a long time that was not updated at the end. I restarted the update as required nb. and then nothing!
The practice turn on the screen toshiba nb out and then the screen stays black, the hard disk does not read it, I tried to put the recovery disk and start it on the drive but nothing, to put the dvd but no operating system, does not read anything...
What happened?? Possible that an update is this damage? The problem and as I said before that I can not act in any way ...!!!
-I can not access the computer in Safe Mode
-always black screen and does not load the hard disk
-I upgraded because I had just reset the notebook with the recovery DVD, so the reader was working, once the update is complete restart of windows I went out this black screen, where I noticed that does not read the hard disk. ..
thanks for all the support and suggestions.
Please send me more 'procedure to execute
Francesco

Hmm you mean you cannot see anything? Neither the red Toshiba Splash Screen?
What to say sounds not good.
But try this short workaround:
Disconnect the AC adaptor, remove the battery. Leave the notebook for some time disconnected from both parts I would wait some hours
Then connect both parts and try to power up
Good luck

Similar Messages

  • [Solved]E17 startup apps don't start after update.

    [2013-01-23 16:30] Running 'pacman -Syu'
    [2013-01-23 16:30] synchronizing package lists
    [2013-01-23 16:30] starting full system upgrade
    [2013-01-23 16:38] upgraded cairo (1.12.8-2 -> 1.12.10-2)
    [2013-01-23 16:38] upgraded icu (50.1.1-1 -> 50.1.2-1)
    [2013-01-23 16:38] upgraded harfbuzz (0.9.9-2 -> 0.9.9-3)
    [2013-01-23 16:38] upgraded imagemagick (6.8.0.7-1 -> 6.8.1.9-1)
    [2013-01-23 16:38] upgraded inkscape (0.48.4-2 -> 0.48.4-3)
    [2013-01-23 16:38] >>> Updating module dependencies. Please wait ...
    [2013-01-23 16:38] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
    [2013-01-23 16:38] ==> Building image from preset: 'default'
    [2013-01-23 16:38] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
    [2013-01-23 16:38] ==> Starting build: 3.7.4-1-ARCH
    [2013-01-23 16:38] -> Running build hook: [base]
    [2013-01-23 16:38] -> Running build hook: [udev]
    [2013-01-23 16:38] -> Running build hook: [autodetect]
    [2013-01-23 16:38] -> Running build hook: [modconf]
    [2013-01-23 16:38] -> Running build hook: [block]
    [2013-01-23 16:38] -> Running build hook: [filesystems]
    [2013-01-23 16:38] -> Running build hook: [usbinput]
    [2013-01-23 16:38] -> Running build hook: [fsck]
    [2013-01-23 16:38] -> Running build hook: [keymap]
    [2013-01-23 16:38] ==> Generating module dependencies
    [2013-01-23 16:38] ==> Creating gzip initcpio image: /boot/initramfs-linux.img
    [2013-01-23 16:38] ==> Image generation successful
    [2013-01-23 16:38] ==> Building image from preset: 'fallback'
    [2013-01-23 16:38] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
    [2013-01-23 16:38] ==> Starting build: 3.7.4-1-ARCH
    [2013-01-23 16:38] -> Running build hook: [base]
    [2013-01-23 16:38] -> Running build hook: [udev]
    [2013-01-23 16:38] -> Running build hook: [modconf]
    [2013-01-23 16:38] -> Running build hook: [block]
    [2013-01-23 16:38] -> Running build hook: [filesystems]
    [2013-01-23 16:38] -> Running build hook: [usbinput]
    [2013-01-23 16:38] -> Running build hook: [fsck]
    [2013-01-23 16:38] -> Running build hook: [keymap]
    [2013-01-23 16:38] ==> Generating module dependencies
    [2013-01-23 16:38] ==> Creating gzip initcpio image: /boot/initramfs-linux-fallback.img
    [2013-01-23 16:38] ==> Image generation successful
    [2013-01-23 16:38] upgraded linux (3.7.3-1 -> 3.7.4-1)
    [2013-01-23 16:38] upgraded qt (4.8.4-1 -> 4.8.4-2)
    One of these packages broke it. Disabled and reenabled the startup apps in the settings but no go. Worked fine this morning when i turned on the computer. Any ideas?
    Last edited by 89c51 (2013-01-23 15:07:48)

    Never mind.
    It fixed itself after a couple reboots 

  • Satellite L40 with no Wi-Fi after Update of Vista

    Hey there,
    i got a Toshiba Satellite L40-137 and installed the Service Pack 1 of Vista.
    And now my WLan/Wifi is just deactivated with no information which driver I need or something..
    Well, it seems like this is a common issue because i googled lots of similar questions but found no proper answer.
    Some Facts:
    1) The little lamp at the bottom of the keyboard doesnt work
    2) the connectivity doctor just tells me wifi is "deactivated"
    3) fn+f8 does absolute nothing
    In case you got any workaround I'd be pretty thankful! :)
    Thanks a lot,
    Heiko

    Hi heiko_1,
    That means this happened after Service Pack 1 installation on Windows Vista?!
    Well, in my opinion you can solve it with driver reinstallation. Just follow the link posted by Mike30 and download the latest version. This should work.

  • Illustrator cc don't start after the new update

    Illustrator CC don‘t start after I update this. I should loading the font Verdana, but Verdana is activ. What can I do now?

    saure sahne,
    Are all the faces of the Verdana and Tahoma fonts installed and enabled/active?
    Did you receive a message about Verdana?
    Is your OS Mac OSX 10.6.8? If so, you will have to upgrade that or roll back the update. You can see instructions for the latter here:
    http://prodesigntools.com/adobe-cc-version-control.html

  • Apps don't disappear after updating

    My updated apps don't disappear after updating concludes on my iPad.  I noticed that this only started happening after installation of iOS7.

    Hi Aleagle,
    Just so you know, the reason this was changed for iOS 7 was in conjunction with the Automatic Update feature that was also introduced with iOS 7. If updates to apps are being done automatically, then you would have no way to know what apps were updated or when. This new list in the Updates tab was added to provide the update history information.
    Cheers,
    GB

  • Iphone 5 wont start after updating ios7.04v

    My Iphone 5 would not start after updating it to ois 7.0.4. It says i need to connect to itunes but when i do it asked me to restore to my original settings. when i tried doing that my iphone keeps crashing

    Hello shefali,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    Connect your USB cable to your computer but not to the iPhone, iPad, or iPod touch until step 3.
    Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
    While pressing and holding the Home button down, connect the USB cable to the iPhone, iPad, or iPod touch. The device should turn on.
    Continue holding the Home button until you see the Connect to iTunes screen. When this screen appears, you can release the Home button:
    Note: If the image of a battery appears, let the device charge for at least ten minutes to ensure that the battery has some charge, and then start with step 2 again. If you don't see the Connect to iTunes screen, try these steps 1 through 4 again.
    iTunes should automatically open and display the following message:
    "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes."Note: If iTunes not open after two minutes, please open iTunes yourself.
    Use iTunes to restore the device.
    Best of luck,
    Mario

  • Webmail in Safari don't work after updating to iOS6.

    Webmail in Safari don't work after updating to iOS6.  Logging on to office webmail account are redirected.  Webmail works with Google Chrome, but it doesn't sove the issue with Safari.  Any suggestions on how to configure Safari?

    Try this
    I was having this problem, seem to happen when waking computer, once finally connected network works great. 
    You need to edit your network preferences to order the network selection list.  Goto this support page  Using network locations (Mac OS X v10.6 and later) and edit your selection list. 
    I also created a "HOME" location and deleted all networks except wifi.  Put MB to sleep woke and safari worked great.  Still I re-ordered the networks under Automatic putting wifi at top, sequence is from top down.  Don't forget to click Apply.  Have fun

  • Only half of the body just below the camera and steel side of camera side is getting heated up just after 10 , 15 mins of usage i my iphone  4 is it normal...as earlier the body was not heating up even after 2 hours....the problem started after updating t

    only half of the body just below the camera and steel side of camera side is getting heated up just after 10 , 15 mins of usage i my iphone  4 is it normal...as earlier the body was not heating up even after 2 hours....the problem started after updating to 6.1.2
    iPhone 4, iOS 6.1.2

    Hi, did you ever solve this problem?
    My 1 year old -- ha! one month out of warranty -- iPhone 4 has been having a nearly identical problem over the past few days.
    It started by dying completely so I had the battery replaced, thinking it was simply battery issue.
    It then worked again for a moment but started doing exactly what you describe, going through a reset cycle (longer than 30 seconds but who's counting). And it felt quite warm.
    Did hard reset, plugged into wall charger and MBP USB but the new battery wouldn't even get a full charge (a whopping 92% after nearly two days). It would even lose battery when plugged in if I opened an app. And all the while plugged in, if I left the phone on, it would cycle through these resets. So I turned it off to try to charge it.
    Now suddenly, it's dead again. Totally black, and hard reset does nothing. Up until two days ago there was nothing wrong whatsoever with this phone! And I hadn't even installed a new app that could be the root of the issue. No idea whatsoever what caused this.
    Any help would be much appreciated!!

  • FF doesn't start after update to version 27.0.1

    FF doesn't start after update to version 27.0.1
    Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

    Firefox 27.0.1 is too new for me to know what unique issues it might have. I will message you a link to download the installer for Firefox 27.0 to see whether that reverses the problem.

  • Could someone explain to me why Flash virtual tours don't work after update to Flash Player 10.1?

    Hello there,
    Could someone explain to me why Flash virtual tours don't work after update to Flash Player 10.1?
    Thanks!

    www.privium.nl
    klick the icon image 'virtual tour' upper right corner.
    This works on my other pc, on which I did not update to 10.1 ...
    (I produced this virtual tour; it is stored on the FTP server of the service provider I use for this)
    Awaiting your reply,
    Regards,

  • Firefox won't start after update - nothing in support pages helps

    windows 7 - firefox won't start after update - no support pages are relevant

    -> [[Firefox will not start]]
    Check and tell if its working.

  • Hi everyone, I've had problems with some apps on my iPad. The apps don't open after update

    How do I fix apps that don't open after update?

    Try a hard reset ie hold the power and home buttons simultaneously until the Apple logo appears (ignore the red slider). Are you still using iOS 4.3.3, as in your profile? A lot of apps now need an iOS of 6 or higher for the update to download.

  • Some apps on my macbook pro will not open,,,they bouce a few times and disappear.  would someone please give me a straightforward answer on why this might be haappening(started after updates))   please?

    some apps on my macbook pro will not open,,,they bouce a few times and disappear.  would someone please give me a straightforward answer on why this might be haappening(started after updates))   please?

    Yay! Solved my own question; just did a hard shutdown, worked like a charm! Funny, didn't before. But who am I to question salvation?

  • Card reader don't work after installing win 7 ultimate on pavilion dv-6 1260ej

    card reader don't work after installing win 7 ultimate on pavilion dv-6 1260ej.
    Tried downloading this driver:
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-75456-1&cc=il&dlc=he&lc=he&...
    still dont work.

    Hi,
    Download and install the Chipset driver on the link below.
    ftp://ftp.hp.com/pub/softpaq/sp45001-45500/sp45041.exe
    After the installation has completed, restart the notebook.
    Next, download and install the Card Reader driver on the following link.
    ftp://ftp.hp.com/pub/softpaq/sp45001-45500/sp45046.exe
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Satellite A300-15A does not start up after Alcohol program installation

    Hi...
    I bought Satellite A300-15A yesterday and after completing the Vista installation process, I tried to install "Alcohol" but my notebook shutdown and now I'm not able to start notebook.
    It is not starting in any mode.
    I forget to make recovery discs. I think Alcohol is not compatible with Vista. Error which i receive is below.
    Can anyone tell me the solution?
    Please help urgently
    "A problem has been detected and Windows has been shut down to prevent damage to your computer.
    If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: blah blah... "

    Sounds like a familiar problem to me, as I had the same one with the Daemon tools. After installing those tools I couldn't start my Windows XP any more. I guess it somehow mixed up some drivers or registry entries, but not sure about that.
    Ok, you can try to deinstall the tool by first starting Vista in safe mode (press F8 before Windows boot up).
    You should be then able to enter Vista without problem.

Maybe you are looking for