Satellite A300 Won't boot after powering off during BIOS upgrade

Hi,
I was trying to upgrade the BIOS after reading an alert from TOSHIBA TEMPRO, after some time, it didn't seem to launch so I ran it a second time, then both BIOS application showed up in the taskbar only and it froze while I didn't start upgrading or anything, I had to power off.
I tried to reboot but now, it just stays on black screen ( the monitor isn't even powered, as if the system wasn't running ), all leds are powered with the "accessing hard disk" flashing, the led from the DVD reader keeps on flashing while making a noise every 3 seconds or so.
I've read on the forum that there may be no solutions but to take it to an authorized service provider, but I'm willing to take any possible solution before doing it.
Thanks for any advice.
Alex.

Yes I did. Thank you. In my case I had to borrow the USB diskete but I was lucky to get to it!.
The problems with the BIOS update are that there is no enough information about how to do the process. I found some important information after corrupting the BIOS while it should be available with the download archive. Also in my case the program started updating BIOS without prompting or anything and couldn't react to prepare everything on time. I could see this happens a lot. There may be a problem with that software because I heard people saying that everything seemed to work fine but then it didin't start up.
The worst thing was that local support service wanted me to change the whole motherboard and then paying a lot for removing one of the passwords saying always that there was no other option even when it seemed they knew that wasn't true! I'm a upset with them.

Similar Messages

PowerMac won't boot after power failure during install

Hi, sorry if this has been asked. I searched, but I'm not quite sure how to phrase it.
I bought a used PowerMac from craigslist and went to install a newer version of OSX. I had a power failure in the middle of the install and now the computer won't boot up. How do I go back to a fresh re-install and get the computer to boot up?
Much appreciated!

Did you use a retail install DVD? If you used a gray disc from another model Mac, that could be a problem.
Because of the power failure, suggest you reset the PMU. How long was the power Off? You may need to replace the PRAM battery.
Resetting Cuda/PMU on Power Mac G5, Power Mac G4, Power Macintosh G3
http://docs.info.apple.com/article.html?artnum=86760
 Cheers, Tom

IMac won't boot after power failure during 10.5.6 update

Help!
Tried to update last night and at something like 80% install, we had a power cut. iMac won't boot at all now - get to a grey screen which tells me to restart. Don't have a wired keyboard. If I did - what are the steps to get this working again.
I believe I have a good backup, but don't want to risk as all the family photos are on the iMac.
Thanks in advance.

Thanks for the help, but can't even get to a screen where I could type anything! I know I'm being dumb here.

Satellite A300 won't boot from any device

I've got an A300 that won't seem to boot from any device.
When I start it I see the splash screen and can enter the BIOS or Boot select.
I've tried setting boot priority to HDD & CD, and also chosen to boot from both with the Product Recovery CD in the drive.
However as soon as it gets past the splash screen I am just presented with a plain black screen.
I hear a bit of CD activity and the light flashes a couple of times but then nothing.
Normally I would expect a prompt to press a key to boot from CD.
I have tried pressing the key anyway but this just seems to result in a default beep.
Could it be the graphics card on the system board?

Hi
> Could it be the graphics card on the system board?
I think this is no matter if the issue would be related to mobo or GPU in both cases the motherboard needs to be replaced. But if you area able to access the BIOS then the mobo could be ok.
But generally speaking it sounds like serious hardware problem and I think its time for an notebook technician.
Anyway, did you try to boot from different CDs? I mean Linux Live CD or Windows PartBE?
Please check this both disks can be downloaded for free

Satellite L855 won't boot after BIOS update

I downloaded the BIOS update and followed the instructions it gave during install, however upon reboot (which the setup initiated) I get a blank screen. The CPU fan intermittently starts and stops. I am thinking that the BIOS update was unsuccessful, how do I resolve this issue?
Thank you,
Neil.

Hello Neil
Generally speaking when BIOS is screwed up you need professional help and you should contact nearest Toshiba service provider and ask for help.
Check also this thread. Maybe this methid can help you too.

IMac G3 won't boot after updating the firmware and upgrading the OS!

Hi! Everyone,
I have an iMac G3 333MHz (five flavors) which comes with 192MB of RAM and 6GB of hard drive. Originally, it was OS 8.5.1 installed, later upgraded to OS 9.2.2. Of course, the firmware has been updated by the appropriate method provided by the on-screen instructions before the installation of 9.2.2. After successfully updating the firmware and installing Mac OS 9.2.2, the system booted up and worked fine. However, after shutting it down and powering it up a few days later, I have encountered a critical problem:
1. At first, the iMac would chime and displayed a smiley-mac finder face.
2. No question mark appeared and the system halted because it stayed at the same screen for about 5 minutes! Also, the keyboard wouldn't respond. For instance, the LED signal light wouldn't light on when Caps Lock was pressed.
3. I assumed that this is just a typical crash and rebooted the machine via the "reset" button on the right side of the machine.
4. After restarting, well, no luck, the same condition. Therefore, I rebooted it again by using the method mentioned above.
5. The condition of sticking at the smiley-mac finder face occurred again! However, this time the iMac wouldn't chime and just displayed the mac face.
6. Another restart, well, it was getting worse... no chime and no smiley-mac finder face but a white screen.
7. I was frustrated then and shut the machine down forcefully by rebooting it again and pressing on the power bottom quickly before the screen appears. Also, I unplugged the power cord.
---------- After a few hours later ----------
8. Okay, I then plugged the power cord in and booted it up again, this time, it would chime but stuck at the white screen. => No smiley-mac finder face appeared!
9. Rebooted it again, the result was as same as step 8.
10. Another restart, the smiley-mac face finally appeared but still... stuck here and this time, no chime.
11. I then shut the machine forcefully by using the method mentioned above and let the machine rest for about a day with the power cord unplugged.
---------- After resting for a day ----------
12. I booted it up and it would chime, but no screen (the power button was orange, not green). I then forcefully shut down the machine.
13. Waited for about a minute and powered it up. This time, I tried to clear the PRAM, but no chime and gave me a white screen. => No luck! As mentioned, the keyboard's LED signal light wouldn't light on even though the Caps Lock key has been pressed.
*Note: The keyboard has been tested on the other computers and it worked. Also, I tried different USB ports to plug the keyboard in. => The USB ports were all in working condition， as I can know from the last successful start up.
14. Forcefully shut the machine down and tried to enter the Open firmware, no luck. It didn't enter and gave my a white screen.
15. Conclusion:
1) After resting for a while, the iMac would chime.
2) Rebooting too much times would cause the machine not to chime and leaded the screen to become white instead of the smiley-mac finder face.
3) However, rebooted the machine when the screen became white, the smiley-mac finder face would appear again without chime.
By the way, I could hear the hard disk spinning up so that means the hard disk is working.
Can anyone help me solve this problem? Is it related to the firmware update? Any suggestions will be appreciated! Thanks!
Andy

OK, I will try replacing the PRAM battery. Also, the PowerMac G3 and the other iMac 233MHz had the dead batteries. They are still working though... Should I replace them along with the iMac 333MHz? In case of not replacing, will they malfunction in future times? There are some symptoms on this two machines: 1. iMac 233MHz - No chime and no sound when adjusting system volume (the bi sound is not available), but iTunes and other applications can still use the audio device and output the sound via internal speakers; 2. PowerMac G3 450MHz - Will chime but sometimes hard to boot: 1) Chime but no screen; 2) No respond after pressing the power button => the power signal light won't light on. Every time I experienced this, I would open its case, pressing a small button (not quite understand what it does... anyway, just works if system halted.) near the PRAM battery and wait for about a minute, then close the case, and it boots. However, I have to reset "Date & Time"...

Mac won't boot after power chord became unplugged accidently.

Mac won't boot after power chord became unplugged accidently.
I have a Mac Mini running very latest version of OSX. I was making a recording with QuickTime; when I needed to plug in a USB recording device into the back of the Mac Mini, as I pulled the Mac off my shelf to do this, the power cable came out and the Mac lost power.
I plugged it back in and powered up the Mac. I get the grey screen with Apple logo and the spinning grey wheel; then it goes to a blue screen (as usual) and I get the "starting OSX..." progress bar. When the progress bar finishes, I'm left with a blue screen only, no dock, no apple icon at top left, nothing across the top, no nothing.
So far, I've booted from the original disc and repaired the permissions as well as the disc, then re-booted, but same old blue screen.
I have another iMac G5 machine, so is there any way I can at least retrieve the important HD files from the Mac Mini to my G5, before throwing the broken Mac Mini away?
Can anyone advise please?

Hi, Nigel.
Not to differ with my colleagues here, but there's an important question that wasn't asked.
1. You wrote: "So far, I've booted from the original disc and repaired the permissions as well as the disc, then re-booted, but same old blue screen."Did Disk Utility report any errors it could not fix when you ran Repair Disk? I suggest you run the procedure specified in my "Resolving Disk, Permission, and Cache Corruption" FAQ. Perform the steps therein in the order specified.
2. You may also want to run the Apple Hardware Test that came with your Mini to be sure nothing shorted when the power cable was removed from the computer. I've seen it happen, hence I usually recommend removing the power cable at the wall before disconnecting the power cable from the computer. See my "Apple Hardware Test" FAQ.
3. Repair Disk gives your Mini a clean bill of health, the blue screen may be the result of some Startup or Login item that was corrupted due to the sudden power outage. My "Troubleshooting Startup and Login Items" FAQ can help you pin that down if such an item is causing the problem and may help you avoid and Archive and Install.
4. If you elect to go the Archive and Install route, see my "General advice on performing an Archive and Install" FAQ for some important tips on this process.
5. As FYI, this is the kind of problem that makes one glad they've implemented a comprehensive backup and recovery solution. For advice on the backup and recovery solution I employ, see my "Backup and Recovery" FAQ. Computing without a comprehensive backup and recovery solution is like driving without auto insurance.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Mac won't boot after updating to OSX 10.6.4

I am on my 3rd Mac that won't boot after updating to OSX 10.6.4. One MacBook Pro and two iMacs. I fixed one but the last two are getting the better of me. HD is not fried. Have tried every keyboard shortcut on startup, Disk Warrior via. Target Disk, repairing permissions in single user mode. The machines will not boot off of a CD or DVD and it will not boot up in safe mode. Something in the startup files is preventing startup. I am suspecting Sophos antivirus. I tried to uninstall it and trash it but I think it's still blocking something. Any help would be appreciated.

Got it! Not sure if removing Sophos had anything to do with it but here's what I did.
1) boot dead machine in Target Disk Mode (iMac)
2) boot good machine off Snow Leopard disk (MacBook)
3) install OS to dead machine- I found this next part very curious. When the install was complete the MacBook restarted as the iMac.
4) ran software updates
5) shut down MacBook then shut down iMac
6) rebooted iMac- all was good
I actually did this twice because a co-worker had the exact same problem on her MacBook Pro. Got both fixed today.
Thanks everyone for your help!

Mac OS won't boot after 2007-009 1.1 update

Hi all
Fairly major problem here. Mac OS X won't boot after the 2007-009 1.1 security update.
What I am left with is the mac boot screen, and not a lot happening. No rotating loading animation.
Any help would be really appreciated.
Thanks

I have been booting up for...2.45 hours now
Good grief!
Here are a few hints about what you should have done:
There are no guarantees, but following this procedure when installing updates and upgrades on your Mac will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.9 to 10.4.10. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
If you are updating Safari (or just have):
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed 10.4.11 and Safari is crashing, the very first thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari. Remember: Tiger up to 10.4.10 used Safari 2.0.4 or, if you downloaded it, Safari 3.0.3 beta. Safari 10.4.11 uses Safari 3.0.4 which is not a beta. If Safari 3.0.4 on 10.4.11 is not the fastest browser you have ever used, then something is wrong!
Moreover, trying to revert to Safari 2 when running 10.4.11 can have repercussions, as Safari 3.0.4 uses a completely different webkit on which other applications like iChat, Mail and Dashboard Widgets etc also rely.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party ad-on. Two such add-on that have been frequently mentioned here for causing such problems are Piclens and Pithhelmet. If you have them, trash them.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692

M8330f PC won't boot after accidentally having I-pod plugged in prior to booting

My computer won't boot after having my i-pod charge cord inserted in computer prior to booting. I have tried f8 f9 f10 f11 nothing is getting me to a point where I can actually get the computer to boot. I realize I may need to provide more info, but don't know what else to provide you right now. HELP!

I used version 1.B for my motherboard.
Yes i did. I describded what happens, when i run 1 and 2 sticks.
-If these are timings then - 9 9 9 25
-1600mhm before bios update and 1337mhz after update
-Voltage: 1.5V in auto probably
Edit1: I got a response on other forum -
Could this be true:Quote
The Hyper X Fury operate off of PnP and aren't compatible with the P55 chipset natively?
In that case i could try to refund the ram, cause the place where i bought it said its compatible with P55
Edit2: I added some info on what kingston homepage (no P55) says and specification pdf also what my seller says in description of this ram type:
I`am am confused, honestly.
Edit3: Aperrantly its might not support my p55 chipset, found a reply on another similar problem tread replied by kingston tech support:
Quote
Hi, I'm Jewel with Kingston Technical Support and would like to offer some clarification. Our currently manufactured memory, including the HyperX Fury line, is compatible with Intel 6-series chipsets and later. The DH55TC has an Intel H55 chipset which is part of the Intel 5-series chipsets. As such, the HyperX Fury memory is not compatible with your system and we do not currently offer any memory that would be compatible with your system. You can try looking online for recently discontinued part numbers like KVR1333D3N9HK2/8G or KVR1333D3N9H/4G which are compatible with your motherboard. If you are unable to return the memory to your place of purchase, please contact us and we will do our best to work with you. Please check http://www.kingston.com/company/contacts to reach support in your area.
If that`s the case then - outdated spec information everywhere...

Toshiba Satellite A300-20T shuts down after 5 seconds!!

my laptop satellite A300-20T shuts down after 5 seconds of booting , i dont know why ?? and i searched for support in the website and didn't find it in the model list, also i don't know why ???!!
i want to know why it shuts down , and how can i communicate with support

Yours would not appear to be a US model. We need the Part Number for your laptop, like PSAG8U-05K02C. You can find this on the Toshiba label on the bottom of your laptop. As well, what country was it originally purchased in. In addition, what is your operating system version, like Windows Vista 32bit?
Mike

System powers off during boot and I have to repair

Hello,
I am having a niggling problem with a Lenovo 3000 n200 with both Vista and Windows 7
1. close lid, system goes into standby
2. After a couple of hours system powers off ( power cable is in)
3. Power on, system starts booting and powers off, turn power on again and problem repeats indefinitely
4 To overcome problem I select repair and recovery, this sometimes powers off once or twice too, but eventually system boots, repairs and works fine.
I have rebuilt system several times and tried 3 different hard disks.
Problem occurs with both 3.03 & 3.05 firmwares
thanks for your help,
Taggn8tor
Solved!
Go to Solution.

Does this still happen when the battery is removed and is on PSU only, if it does then I have bad news for all you guys, the laptop will require a new motherboard and unless you have an extended warranty then this could be an expensive repair.
Apparently Lenovo call this fault a "Boot on cold issue" and seems to be a common problem with the N series which are over a year old. I personally think it's a single part failure on the motherboard or manufacturing fault.
To find the part number for the motherboard remove the RAM and under there will be the part number for the motherboard which will look something like 1r7694, 43n7652, 41r7695, 43n7654 etc.
The problem you have here is will a replacement motherboard after a year have the same fault?
I would also look up the Consumer Protection act and check out the part which says Fit for Purpose.

Macbook pro won't boot after installing update 10.9.3

macbook pro won't boot after installing update 10.9.3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

MacBook Pro won't boot after trying to install 10.7.3 update. Start up stalls at Apple logo and spinning gear.

MacBook Pro won't boot after trying to install 10.7.3 update. Start up stalls at Apple logo and spinning gear. Computer won't even start in safe mode.

My daughter's MacBook Pro was doing exactly the same thing. I don't know if it had anything to do with the latest update. She called me about a week ago saying that her MacBook began running slower by the day . She then called me Friday and told me that it wouldn't get past the gray screen and the gear just kept on spinning. I did everything I could over the phone including Safe mode which it wouldn't go into and thought maybe it was the hard drive. She took it to the Apple store. Originally, they also thought it was the hard drive. It ended up being a corrupted operating system (Lion). Apple genius simply re-installed Lion and she's back up and running. Good thing she backed up right before it crapped out. She'll be restoring everything tonight. Don't know if re-installing Lion will help your situation, but it did the trick for my daughter.

[SOLVED] Arch won't boot after I created a separate /var parition

Arch won't boot after I created a separate /var parition on an existing installation.And let me confess: it was maybe stupid trying to do it on an existing install.
I edited the fstab correctly, copied the files using rsync preserving permissions. Then I kept a backup of /var using tar. Then went on to delete everything under /var, ie /var/*, the /var folder is still there. All this I did from a live CD. After that I booted into my arch linux. Here I get messages about systemd successfully finishing fsck on each of my partitions, then the screen starts blinking. And there is no more output. Pressing Ctrl+Alt+Delete causes systemd to stop its services and reboot.
Having realized I had borked my system, I removed the /var line from fstab and restored /var from the tar file I made earlier. Again I did this from a live cd. Rebooted into my arch system, and again similar issues, namely that after fsck and messages informing a few services had started, the screen keeps blinking.
The live cd I used for reorganizing my partitions was elementary OS freya. They have GParted in there. I also have an arch install iso lying aroung from May 2013. If necessary, I can download the latest version. I am currently typing from a Windows installation I dual boot from.
I don't know how to extract any boot logs as I am locked out of the system. Here is my fstab in any case:
# Filesystem information
# /dev/sda5 LABEL=fs_root
UUID=b9d739cf-fd8c-46dd-a919-bd827dc47c66 / ext4 rw,noatime,data=ordered 0 1
# /dev/sda9 LABEL=fs_var
UUID=ec0f7a49-dccd-43ab-8651-9aa3fdb41cc7 /var ext4 rw,noatime,data=ordered 0 2
# /dev/sda2 LABEL=fs_boot
UUID=0e8ab31a-3bda-4b85-a901-a36f21b1583d /boot ext2 rw,noatime 0 2
# /dev/sda6 LABEL=fs_home
UUID=d9e63c47-274e-447f-ad01-0d97afe0fd34 /home ext4 rw,noatime,data=ordered 0 2
# /dev/sda7 LABEL=fs_swap
UUID=7301227c-e9f3-41b8-9d0f-4cf3c159491c none swap defaults 0 0
# /dev/sda3 LABEL=fs_win
UUID=12B639D1B639B5D7 /fs_win ntfs uid=1000,gid=1000,dmask=027,fmask=137,showexec,nofail,noauto,x-systemd.automount 0 0
# /dev/sda3 LABEL=fs_share
UUID=D272269772268079 /fs_share ntfs uid=1000,gid=1000,dmask=027,fmask=137,showexec,noauto,nofail,x-systemd.automount 0 0
I would greatly appreciate any help.
Last edited by richcocoa (2015-05-03 18:04:44)

Have you moved everything from /var to /new_var (i named it for learning purpose)? You shoud copy content from /var but not on the fly but booting from arch iso cd, and than you shoud mount your / into arch-chroot environement, mount all of your mount points and than copy content from default /var to new /var. The copying should be done with this
cp -rax
and you can add -v switch to verbose output. I have my own /var moved the same way.
The simples way is:
-boot the arch iso cd
-mount all of your mount point (i created here in this step /new_var to move /var to a new place, and this /new_var i put in /etc/fstab as /var later)
-copy /var to /new_var with -rax or -vrax (recursive, archive, this filesystem or verbose, recursive, archive, this filesystem switches)
-umount all of it
-reboot.
Last edited by firekage (2015-05-02 07:49:20)

Satellite A300 Won't boot after powering off during BIOS upgrade

Similar Messages

Maybe you are looking for