Satellite A500-03P: Cannot connect to WLan using Win 7 + Event message

Hi all,
I very recently bought the Satellite A500 with the included offer of Windows7 when it was available end October 09.
So I got the DVD from Toshibe for the upgrade and followed the steps and upgraded from Visa home premium to Windows 7. I have two issues now.
1) I am getting a System Event Notification after start up, telling me about the system event log. The full message is below.
Failed to connect to a windows service
Windows could not connect to the System Event Notification Service service. This problem prevents limited users from logging on to the system. As an administrative user, you can review the System Event Log for details about why the service didn't respond
2) I was able to use this laptop for the internet PRIOR to the upgrade, both via a wireless USB drive as well at office via a modem ADSL.
Now I cannot access the internet after the Windows 7 upgarde!!
As an example the Optus dial up pop up box appears andwhen I click "connect" it does not connect.
Can anyone help please??
Thanks
C I

Hey buddy,
1)Have you checked the Service Configuration for this service? The start up type of System Event Notification Service must be always set to Automatic. This service is absolutely necessary for Windows and shouldnt be disabled or set to manual start type.
Check this!
2)To be honest I never heard about internet PRIOR but normally it should also be possible to access the Internet with Windows 7.
Make sure that the WLAN and/or LAN card is installed properly and check the TCP/IP settings. If you are missing some driver you can get it on the Toshiba page.

Similar Messages

Satellite A500-15M: Cannot connect to TV using HDMI

Hi,
I have a Satellite A500-15M. I recently tried to connect to my TV so I could watch some online shows on my Hannspree Xv HD ready TV.
The HDMI out doesn't register at all on the TV - the TV displays a message 'not supported' and remains blank (as if there is no signal) - On the PC display settings it doesn't recognise the TV... in fact it [Intel Graphics and Media Control Panel] says that monitor/TV settings are not supported.
But I can connect via the VGA output - although I have to drop the display settings down to 1024x768 for it to show on the telly. Additionally the display on the TV then is mostly pink and red, even though my pc display pic is mostly blue. - the Toshiba start up screen shows on the TV without any issues, and a couple of times the log in screen has displayed fine too, but then sometimes it doesn't...
I know it is not the VGA cable as I can connect to the TV with it on my wife's advent netbook without any issues.
Are there any drivers I need to update/ download? Or settings I need to change?
How can I get my display onto my TV?
Any help would be greatly appreciated. Thanks

Hi
First of all you should connect both devices (notebook and TV via HDMI) when both devices are powered off. After that power up the TV and the notebook.
You should choose the HDMI channel on TV and then should use the key combination FN + F5 in order to switch the video output to the TV.
If it does not help, try to update the graphic card driver.
It seems your notebook supports the Intel graphic chip. Therefore you could check the Intel page for new drivers.
Greets

AMD CPU with Vista cannot connect to WLAN using MS-PEAP with WEP-128

We have a notebook "HP Pavilion tx1000 (AMD Turion64 CPU with Vista 32bits)". The notebook is using Broadcom 802.11a/b/g chipset, running AMD and Vista. It cannot associate to WLAN using MS-PEAP and WEP-128. Also, it cannot associate to PEAP and WPA2-AES.
The AP's log shows:
Oct 11 15:35:20 CCT: %DOT11-7-AUTH_FAILED: Station xxxx.xxx.xxxx Authentication failed
The ACS's log shows:
"EAP-TLS or PEAP authentication failed during SSL handshake"
We do not validate the certificate in the wireless setup. Vista's WLAN AutoConfig is used to configure the wireless profile. We are running Autonomous AP with Switch-Based WDS (WLSM).
We have no issue with Intel Centrino on the above authentication and encryption scheme.
Have checked the CCX program, broadcom 802.11a/b/g chipset is supported only for windows 2000 and xp. There is no mentioning about support for vista. Could this be a compatibility issue?
Please advise and thks

Maybe look at this post: http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddf9be9/5#selected_message

Satellite Pro M70: Cannot connect to WLan with ConfigFree

Hi in Forum.
I'm having trouble with a Satelite Pro M70, concerning gaining control of wireless conections.
When scanning with "The Radar" i ConfigFree for available wireless accesspoints, I get several points available, but is not able to connect to a single one of them. I can read their status and see their WEP encryption marker.
When I try to connect to any one of them, I get a pop up dialog box, which says (translated from danish) "Another suppliers software is in control of the wireless adapter". When trying to set up a connection through the classic windows way, windows states that "windows is not able to configure this wireless connection - if you have another program to administrate wireless connections you must use this". I suppose it refers to ConfigFree...?
Is the unnamed "other supplier" Windows related or maybe McAfee related (Security Suite 2007)?
If you're familiar with this problem or something like it I would be please to know.
By the way - where do I enter WEP encryption keys for my friends WLAN routers in ConfigFree?

> When trying to set up a connection through the classic windows way, windows states that "windows is not able to configure this wireless connection - if you have another program to administrate wireless connections you must use this". I suppose it refers to ConfigFree...?
It must be not a ConfigFree. Depending on you WLan card an Intel ProSet utility or a Atheros Client utility could controls the Wlan configuration!
Please check if one of the both tools controls the wlan and disable the function!
> where do I enter WEP encryption keys for my friends WLAN routers in ConfigFree
You should have three different tabs in the Configfree utility.
The second one Device settigns provides device list and there you should find Wireless network connection.
Choose it and use the button Network connections.
There you should find some encryption settings!
Please check also the Profile settings tab and the option called Security settings

Satellite A500/02U cannot connect to mobile phone using BT - detection of service failes

Hi
I have only had my laptop a week but when I go and connect to my sony ericson phone it while see the phone try and pair it but keep coming 'detection of service failes'....
Phones brand new also and connects to everything else bluetooth so its definately this laptop. driver has just been installed so cannot be this....feel this taking teh laptop bakc to teh shop and getting them to fix it if I had the energy.....can anyone help with this?
Thanks
Eddie

Before you contact anyone try to install latest BT stack.
Strange is that I found several identical threads in different forums about this issue but always with Sony mobile phones.
If you have some time check THIS interesting thread.

Satellite Pro 6100 - Cannot connect to WLAN router

Hi there,
I have brought a 2nd hand Satellite Pro, Model version SP6100 (PS610E-029ZV-EN), P4 1.7Ghz, 512Mb, 30GB, with Windows 2000 Pro loaded.
I cannot get the wireless to connect to my router. The switch is in the correct position.
I want to change to XP using the key supplied with the laptop from new (dual OS) however I can't get it to reformat using an XP disc at start up or if I use the recovery cd (start with holding C down and release when it runs up) it begins but displays "invalid drive specification" three times and loads Win2000.
Can anyone advise how (or if!) I can reformat as I would like?
Any help will be greatly appreciated.
Cheers.

Hi Jaba,
I'm quite happy to 'start again' and erase the existing partions via reformatting however I do not know how. I have tried starting with the XP disk in the dvd drive but it starts up in to 2000 without reading the XP disk.
I would prefer WXP than W2000 as it will be for home use.
If you or anyone else can advise on how I proceed from here I would be very grateful.
Cheers All.

PI 7.11: Cannot connect to server using message server:...

Hello Guys,
we make the Application Management for a Customer PI System.
Scenario:
- the SAP Gui Connection to the ABAP Stack is routed via SAPRouter and Works fine.
SAP Gui -> our SAP Router -> VPN Box from Customer -> Firewall Customer -> ABAP Stack PI System
- WebAccess its working fine, the Customer use Webdispatcher on every PI Server...
Browser -> VPN Box from Customer -> Firewall Customer -> Java Stack (Port: 5xx00 btw. 81xx (Webdispatcher))
Problem:
Our Problem ist, we can not proceed the Integration Builder or the ESB, the Java Web Start works fine and open the Logon Screen Correctly -> but i fill the Logon Screen with my User name and Password and press Logon come the follwing Error:
"Cannot connect to server using message server: ms://<hostname>.<domain>:8134/P4"
In the Details from the Error Message:
"<hostname>.<domain>:53404 Reason: com.sap.engine.services.rmi_p4.P4IOException:
Cannot open connection to host: <IP-Adress of Central Instance> and Port: 53404"
The Customer says, the Firewall is open with the IP Adresses and P4 Port but i dont think so...
Can everybody help me, or have tips for me! I have checked a lot of OSS Messages (PI High Availabilty etc... its all correct on the System)
Sorry for my bad English
Best Regards,
Markus

Hi Markus,
did you check if the browser is using a proxy? (In this case your scenario unfortunately won't work).
P4-port should generally be routed via a proxy (described in the help.sap.com), but within the PI-Tools(JNLP) the proxy-usage is not implemented. There is even a SAP-note that describes how to check the JavaWebStart-Proxyconfiguration, but this won't help either.
If there is a proxy defined in the browser everything is working fine till you pass the logon-screen but even with the correct "javaws"-settings you won't be able to go on.
(This problem is pretty bad if you do have developers and the SAP-servers seperated because of security issues. I'm hoping that this malfunction will be solved with upcoming patches.)
Solution: Establish a connection without any proxy in between.
E.g.: a terminal server in the same network
It would be helpful to find more people with the same problem to force a fix from SAP for that.
If anyone else is having problems with this, please add a comment to this thread.
Best regards
Christian

Cannot connect to server using message server: ms://xiidhasoft:50004/P4

Hi SAP Guru's
When PISUPER or any any of the enduser is trying to login in the Integration Builder , they are getting error
Cannot connect to server using message server: ms://xiidhasoft:50004/P4
I have tryed to search in SDN and got below solution but no success
1. Exchange Profile of PI - http://host:port/exchangeProfile
2. Check with the rmi port number.
3. if rmi port number is empty or any number is present ( check with Tr code: SMICM - services - check for p4 port number - it will be ex: 5<nr>04)
4. fill the rmi port number as present in the P4.
OR
implement note 864268
I have Netweaver PI 7.1 .
Please suggest some alternative solution.
Thanks & Regards
Vinay Patel

You may check your local PC Java Network Setting.
Troubleshooting:
Probably Javau2122 WebStart does not detect the correct Proxy Settings. In this case please proceed as follows:
To change the Proxy Settings for Javau2122 Web Start:
1. Click Start --> Run and enter javaws. Press button OK.
2. Control Panel -> Programs ->Java -> Network Settings...
3. Select Direct Connection to switch off the proxy settings and press button OK.
If this still does not work, select Use proxy server to set manually the HTTP Proxy and Port.
Contact your network administrator for the correct settings.

Since a I have intalled OS X Lion I cannot connect internet mobile using my ZTE mobile pen

Since a I have intalled OS X Lion I cannot connect internet mobile using my ZTE mobile pen.

It sounds like you need updated drivers. They are hard to find for that thing. This is what I found on a cursory search:
http://studiofourfour.zendesk.com/entries/20305042-mac-os-x-lion-3-zte-usb-broad band-drivers
You should consider contacting the manufacturer or cell provider that sold you the modem for support.

Can I Use DAQ Event Message 9 with My PCI-6033?

I would like to handle my counter board's interrupts by using DAQ event message 9. If Yes, I would to like to see an example in VB?

Counter events are not supported under NI-DAQ for E series devices. It is possible that what you are trying to accomplish could be done just as easily with a timed loop in DAQmx, what is your application?

Satellite Pro 6000: Cannot find correct WLAN driver

Hi,
I have re-installed Windows Xp on my notebook Satellite Pro 6000. All is working except for the wireless connectivity.
When looking in the device manager, I see that the WLAN driver has not (or incorrectly) been installed.
So looked at the Toshiba site for the corresponding drivers, but I am not able to find the correct one. I did found some drivers, which seems to be the one, but unfortunately after installing the drivers, the wireless connectivity is still not available.
Any help would be appreciated.
Thanks in advance.
Regards, Robert

Hi
I dont believe that you cannot install the Wlan driver.
Go to the device manger and find out which Wlan card was installed. (check properties)
If the WLan card is placed under network adapters so the driver was installed properly.
But if you see a unknown device in device manager so you need the WLan driver.
Then download the WLan driver from the Toshiba site. Be sure that you use the right driver for the right OS!
You can try firstly to uninstall the old driver and then to install the new one.

Satellite A500/02J: Cannot get REGZA/HDMI link to work

I have a Satellite A500/02J laptop with hdmi out, and i have a hdmi control program pre-installed from toshiba.
I just recently purchased a REGZA 32AV500A LCD toshiba television and have my computer running through the tv via hdmi.
However, my tv has regza link and as far as I can tell my computer supports regza/hdmi control however i cant get the link to work.
I have a windows meda centre remote which i can use to put the computer to sleep and wake it back up.
However one remote is better than two, also i need to be able to boot the computer from shutdown just by turning the tv on. Under hdmi control i can set the computer to shutdown when the tv is turned off however i dont know how to have the computer boot from shutdown simply by turning the tv on.
Any help would be greatly appreciated!!!!!

Hi
The user manual says that the remote control of the connected TV can be used to operate some of the computer functions which are:
use the TV remote control to output the computer screen onto the TV screen
use the TV remote control to launch operate and close applications on your computer
Turn on the TV when the HDMI output is selected using the FN + F5 key
Switch the video output (HDMI or LCD) when executing certain desktop icons
Enable/disable the REGA link function on the computer
But you should also check your TV settings and notebooks BIOS settings.
Im not quite sure if the HDMI REGZA option is available in the BIOS but its worth a check
I have scoured through the user manual trying to find an answer to this. Im not trying to use the remote to control the tv, I want to use the computer to tell the tv to power up. I have a logitech K400 keyboard that I use to both put the computer to sleep and to wake it up.
However, I want the tv to auto power on (and auto power off once the signal is removed) once I wake my computer back up and a signal is sent through the HDMI cable. REGZA link indicates that this is possible, both my tv and laptop have REGZA link. I want to eliminate the remote from my living room.

Satellite L300D PSLC0E - Cannot connect to TV

I have a problem with either my laptop or TV. I have a Toshiba Satellite L300D model number - pslc0e-017017en.
I'm trying to use a VGA wire to a Samsung TV but its not working.
I've try FN+F5 and nothing appears. Is this a common problem, do I need 2 install something?
Please help.

Hi
The question is what cable did you use and how did you connect it to the TV and if you have chosen the right channel on the TV!
As far as I know this notebook supports ONLY VGA (RGB) port. Using this port you can transmit only the analog video signal.
For example; you cannot connect VGA to DVI. This will not function!
If you want to connect the external monitor you will you have to use the VGA cable and should connect the both devices using a VGA cable.
By the way; its very important that you would use the Toshiba certified graphic driver!!!

Cannot connect to database using the Upgrade Simulation Tool

I have installed the Upgrade Simulation Tool on my system and when I try to run the tool my system works in the for awhile in the background and creates the _Simulation mdf and ldf files and a .bck file. After 3 or 4 minutes it gives me an error "Cannot connect to the database".
It looks to me like it is connecting to the database because it is creating the files in the SQL Data folder. I have tried to run it on several databases and get the same results.
Thank you, Jeff

Hi,
You may not have the ability to upgrade it directly.
He does have the ability.
When downloading Pl 42, it is cleary marked as "Upgrader", which means it can be used for upgrade (in this case simulation) from a lower version than 2007A
Patchlevel which are marked as "patch" are suitable only for updating the PL within the very same version of SAP Business One.
This tool should run under 2007 system I believe.
The Upgrade Simulation tool was designed in orderto test an upgrade, therefore it can run at a machine where 2005 version is installed. Technically speaking it creates a second SBO-common, which can be used only with the special designed (read only) client of the tool.
Jeff, you should check access rights of your SQL Data folder.Maybe grant user "Everyone" modifying rights to that folder. In addition you could try to detach a DB and move the related *.mdf and *.ldf to another folder where no access denied rights were applied.
If using MSSQL 2005 create via ODBC a Native Client connection to the Server, although you might just working locally only.
Regards
Mario

Cannot connect to database using SQL*Plus

Hi, I have Oracle 10g XE installed in my labtop and I cannot connect using SQL*Plus.
I can connect using the broser User Interface though, which I was able to do after doing the following procedure to change the password of the sys account:
-     open a command prompt
-     - type sqlplus
-     On the “Enter user-name” line, type /as sysdba
-     On the SQL> prompt, type alter user sys identified by NewPassword;
But the thing is that even though I am able to connect using sys/NewPassword from my browser UI, I dont get the same result when doing it using the SQL prompt.
What I am trying to do is this:
SQL> connect sys/NewPassword
Then I get first a warming saying that I need to use either sysdba or sysoper to connect to the system account, but neither of those work.
Can anyone advice me on this matter?
Thanks in advance

Thanks for that.
I run the command to list the usernames on the database and I got SYS and SYSTEM in the list. But again, when I try to use SYS with a password that I know is working because I can access it through the browser UI, it doesnt work. It seems like this sys is different to the sys I used in the UI.
I dont know if I am explaining myself correclty... In the Browser UI I use sys, and a password and I get connected to the sys account. However, if I try to use the same sys.password combination from my sqlplus prompt, I get error messages
Does this make sense at all?

Satellite A500-03P: Cannot connect to WLan using Win 7 + Event message

Similar Messages

Maybe you are looking for