Satellite A500: Low screen resolution using Win 7
Hi,
I've looked around the forum and haven't found any real solutions to my problem so...
I recently bought a Satellite A500 and did a fresh install of Windows 7 Professional on it.
Apparently I was supposed to just upgrade it in order to keep the drivers but being the noob I am, I didn't.
So now my resolution is stuck at 1024x768 or 800x600, neither of which are native.
I've downloaded the win7 64-bit drivers from the Toshiba website, but apparently I already have the latest ATI driver installed.
However I still can't change the resolution and my monitor is recognized as generic non-PnP.
Is there any way to check if I have the display driver already?
And also any solutions to the display problem would be much obliged. It's the only thing left bothering me now about this new laptop.
Hi
I assume you are using Win 7 64bit OS since you have chosen the Win 7 64bit display driver is it right?
What A500-xxx do you have exactly?
The Toshiba European driver page provides three different display drivers for A500 series; Intel, nVidia and ATI
Seems three different graphic chips have been installed in A500 series
You should firstly check what graphic chip your notebook uses
Then go to device manager and uninstall the installed display driver.
Then visit the Toshiba European driver page, download the right display driver for the graphic chip and install it.
After that reboot the unit and check how the notebook would run.
Greets
Similar Messages
-
Re: Satellite L30D - Low screen resolution after Windows 7 installation
I have installed Windows 7 on my Satellite L30D. Since this installation, I cannot have a better resolkuton than 1024x768.*It was much better with Windows Vista.
I have downloaded the latest ATI driver. No effect. I cannot find the Catalyst Control Center as well. What can I do?Hi
The Satellite L30D isnt known to me...
Do you mean Satellite L30 or Satellite L300D?
Normally you have to install the display driver if you want to use higher screen resolutions but check the specifications of your internal display first. Maybe the native screen resolution is 1024x768 and you cant use a higher one.
You can download all drivers for your notebook on the Toshiba website!!! Dont use the drivers from ATI directly, they are not designed for mobile chips. -
Can't start MAIL or STORE because of "too low screen resolution"
I can't start either mail app or store app because of "too low screen resolution".
My netbook (eMachines eM350) has maximum 1024x600, these app require at least 1024x768I have developed a lot of code, and while more recent machines have higher resolutions, I find it prudent not to assume everyone has an 8K panel
No one cares much what you have or have not done, this thread is not about you. If you'd actually developed any Modern apps you'd know that the minimum resolution for them is, as has been stated numerous times here already. Stating that you develop for 640x480
displays clearly indicates that you've never developed a Modern app. Additionally, it should be obvious even to you that a minimum resolution of 1024x768 does not assume that everyone has "an 8K panel".
go write some shaders you clearly have no idea whatsoever about development
i can make programs rescale to fit any screen size, just because you are too stunned to figure that out
programmatically designed dialogs can adapt
Place your rig specifics into your signature like I have, makes it 100x easier!
Hardcore Games Legendary is the Only Way to Play!
Vegan Advocate How can you be an environmentalist and still eat meat? -
Not clear images with lower screen resolutions on Tecra M5
Hi,
we have some M5s with Intel graphics board which work fine with the usual 1024*768 screen resolution.
Now we are buying some new M5s equipped with nVidia Quadro, and they seem to have a native resolution of 1400*1050.
If I try to scale resolution to 1024*768 or even 1280*1024, images are badly out of focus. But I think icons at 1400*1050 on a 14" display are really too small, for the average of users.
No solution?
thanksThis is to do with the native resolution of the LCD. Unless you display at maximum resolution, any attempt to work at a lower resolution will require the graphics card to rescale, causing the resultant image to blur as the graphics card interpolates.
The only solution is to use Windows Vista because the GUI has been designed for larger native LCD resolutions, meaning the icons are designed bigger (approx. twice the size of XP) -
Windows 8.1 Lock Screen drops network connectivity when screen locked using Win+L
Hi!
I was sent here from Microsoft Community forum. The question is:
Since Windows NT 4.0 I'm using Lock Screen to prevent people from accessing my computer when I'm leaving my room. First I was using CTRL+ALT+DEL / Lock Screen, then switched to Win+L keyboard shortcut when it was first introduced.
Everything was fine until I switched to Windows 8.1 computer (Sony Vaio Duo 13 with Broadcom wireless network controller). This machine is 8.1, not 8.0 upgraded to 8.1.
My problem is that when I hit Win+L combo the Lock Screen (with clock etc.) is displayed. Then, despite I have configured not to turn off display, the screen goes blank (after 30 seconds since lock) and network connectivity is cut off from desktop
apps (I suspect the system goes into Active Standby mode, because Modern UI apps like Tune-In radio keep working fine).
100% repeatable scenarios:
## Scenario 1 ##
1) Log in
2) Open desktop app that uses network connectivity. Outlook 2013 from Office365 subscription
3) Check that it has connected
4) Lock screen (Win+L)
5) Wait for 30 seconds (first incorrectly posted as few minutes) as screen goes black
6) Unlock screen (using password)
7) In right corner of Outlook app you will see "Unable to connect with Exchange server" and few seconds later it will reconnect sucessfuly
## Scenario 2 - the more annoying ##
1) Log in to Win 8.1 computer
2) Connect to it using SMB (in my case I wanted to transfer 30 GB of files from local hard drive C: to server) \\COMPUTER-NAME\c$ from Windows Server 2012 R2
3) Start copying files from computer to server
4) Lock the screen on computer
5) As soon as screen goes black server displays message "Lost connection to the resource. Try again?"
6) Unlock screen on the computer
7) Click "Try again" and it will continue copying files
My power settings are set to go into stand by after 5 hours and if I not lock the screen it doesn't go to sleep before 5 hours.
When I lock the screen using Win+L it goes into (probably Active) Standby mode.
Is there any way to prevent it from going to Active Standby when locking screen? I need the screen lock for security reasons but I don't want it to drop my network connectivity on remote desktops, file transfers and other desktop activities before 5 hour
timeout.
This issue is not related to more or less known wireless network connectivity problem that happens to many Intel Haswell computers. Mine doesn't exhibit those problems. I can easly push 100 - 200 GB of wireless data without network drops.
Computer information:
Sony Vaio Duo 13: SVD1322C5E
Intel Core i5-4200U
8 GB RAM
Windows 8.1 Pro 64-bit
Broadcom 802.11n SDIO network adapter
Originally posted at: http://answers.microsoft.com/en-us/windows/forum/windows8_1-networking/windows-81-lock-screen-drops-network-connectivity/099f16bd-b00d-4ba9-b833-48bf1d55ffe4
Best regards,
SergiuszSame issue here using Surface 3 Pro with either internal WLAN or MS USB LAN Adapter. I'm frequently used to keep open connections over SSH to some servers. On switching to lock screen explicitly by pressing Win+L or implicitly due to idle timeout all
connections to servers are lost. In addition, I don't get any notifications on incoming Skype messages (using Skype for desktop) when lock screen is active.
Neither NIC is showing "Power Management Tab" according to step 5 of instructions above.
Additionally observing USB LAN NIC seems to be kept active after activating lock screen, but traffic stops (according to its flashing light) when lock screen is switching off display. Blanking display doesn't seem to be adjustable in System Settings (Energy
Options accessed through Win+X).
Find attached log file of powercfg -energy -duration 300 ...
Log file is in German. It basically claims unset timeouts for deactivating display while running attached to power supply though lock screen is turning off displays within 1-2 minutes.
Energieeffizienzdiagnose-Bericht
Computername
KRITIAS
Überprüfungszeit
2015-01-10T15:07:47Z
Überprüfungsdauer
353 Sekunden
Systemhersteller
Microsoft Corporation
Systemproduktname
Surface Pro 3
BIOS-Datum
10/16/2014
BIOS-Version
3.11.0350
Betriebssystembuild
9600
Plattformrolle
PlatformRoleSlate
Netzbetrieb
true
Prozessanzahl
67
Threadanzahl
1319
Berichts-GUID
{1a168801-c189-46fe-811c-235e6bf2bd0d}
Analyseergebnisse
Fehler
Energierichtlinie:Verdunkelungszeitlimit ist deaktiviert (Netzbetrieb)
Der Bildschirm ist nicht so konfiguriert, dass er nach einer Zeit der Inaktivität verdunkelt wird.
Energierichtlinie:Standbyzeitlimit ist deaktiviert (Netzbetrieb)
Der Computer ist nicht so konfiguriert, dass nach einer Zeit der Inaktivität automatisch der Wechsel in den Standbymodus erfolgt.
CPU-Auslastung:Prozessorauslastung ist hoch
Die durchschnittliche Prozessorauslastung während der Ablaufverfolgung war sehr hoch. Das System verbraucht weniger Energie, wenn die durchschnittliche Prozessorauslastung sehr niedrig ist. Überprüfen Sie die Prozessorauslastung für einzelne Prozesse,
um festzustellen, welche Anwendungen und Dienste den größten Anteil an der Gesamtprozessorauslastung haben.
Durchschnittliche Auslastung (%)
45.31
Warnungen
Plattform-Zeitgeberauflösung:Plattform-Zeitgeberauflösung
Die standardmäßige Plattform-Zeitgeberauflösung beträgt 15,6 ms (15625000 ns) und sollte immer dann verwendet werden, wenn sich das System im Leerlauf befindet. Wenn die Zeitgeberauflösung erhöht wird, sind die Technologien zur Prozessorenergieverwaltung
möglicherweise nicht wirksam. Die erhöhte Zeitgeberauflösung kann auf eine Multimediawiedergabe oder Grafikanimationen zurückzuführen sein.
Aktuelle Zeitgeberauflösung (100-ns-Einheiten)
10007
Maximale Zeitgeberperiode (100-ns-Einheiten)
156250
Plattform-Zeitgeberauflösung:Ausstehende Zeitgeberanforderung
Von einem Programm oder Dienst wurde eine Zeitgeberauflösung angefordert, die kleiner als die maximale Zeitgeberauflösung der Plattform ist.
Angeforderter Zeitraum
10000
ID des anfordernden Prozesses
3476
Pfad des anfordernden Prozesses
\Device\HarddiskVolume4\Program Files (x86)\Adobe\Adobe Creative Cloud\ACC\Creative Cloud.exe
Energierichtlinie:Bildschirmzeitlimit ist lang (Netzbetrieb)
Der Bildschirm ist so konfiguriert, dass er nach mehr als 10 Minuten Inaktivität ausgeschaltet wird.
Zeitlimit (Sekunden)
900
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
USB-Verbundgerät
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_05AC&PID_0250
Portpfad
1,2
Standbydauer (%)
14
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
Surface Ethernet Adapter
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_045E&PID_07AB
Portpfad
1,1
Standbydauer (%)
5
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
Generischer USB-Hub
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_05AC&PID_1006
Portpfad
1
Standbydauer (%)
5
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
USB-Eingabegerät
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_045E&PID_0797
Portpfad
1,3
Standbydauer (%)
14
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
firefox.exe
PID
5968
Durchschnittliche Auslastung (%)
1.57
Modul
Durchschnittliche Modulauslastung (%)
\Device\HarddiskVolume4\Program Files (x86)\Mozilla Firefox\xul.dll
0.60
\Device\HarddiskVolume4\Program Files (x86)\Mozilla Firefox\mozjs.dll
0.27
\SystemRoot\system32\ntoskrnl.exe
0.16
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
System
PID
4
Durchschnittliche Auslastung (%)
0.59
Modul
Durchschnittliche Modulauslastung (%)
\SystemRoot\system32\ntoskrnl.exe
0.24
\SystemRoot\system32\DRIVERS\igdkmd64.sys
0.12
\SystemRoot\system32\DRIVERS\avc3.sys
0.07
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
dwm.exe
PID
6264
Durchschnittliche Auslastung (%)
0.47
Modul
Durchschnittliche Modulauslastung (%)
\SystemRoot\system32\ntoskrnl.exe
0.10
\Device\HarddiskVolume4\Windows\System32\dwmcore.dll
0.09
\SystemRoot\System32\drivers\dxgkrnl.sys
0.06
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
Skype.exe
PID
11008
Durchschnittliche Auslastung (%)
0.26
Modul
Durchschnittliche Modulauslastung (%)
\Device\HarddiskVolume4\Program Files (x86)\Skype\Phone\Skype.exe
0.11
\SystemRoot\system32\ntoskrnl.exe
0.05
\SystemRoot\System32\win32k.sys
0.04
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
svchost.exe
PID
1528
Durchschnittliche Auslastung (%)
0.25
Modul
Durchschnittliche Modulauslastung (%)
\SystemRoot\system32\ntoskrnl.exe
0.16
\Device\HarddiskVolume4\Windows\System32\ntdll.dll
0.02
\SystemRoot\system32\drivers\ndis.sys
0.01
Informationen
Plattform-Zeitgeberauflösung:Zeitgeberanforderungsstapel
Der Stapel mit den Modulen, die für die niedrigste Plattform-Zeitgebereinstellung in diesem Prozess verantwortlich sind.
Angeforderter Zeitraum
10000
ID des anfordernden Prozesses
3476
Pfad des anfordernden Prozesses
\Device\HarddiskVolume4\Program Files (x86)\Adobe\Adobe Creative Cloud\ACC\Creative Cloud.exe
Aufrufender Modulstapel
\Device\HarddiskVolume4\Windows\SysWOW64\ntdll.dll
\Device\HarddiskVolume4\Windows\SysWOW64\kernel32.dll
\Device\HarddiskVolume4\Windows\SysWOW64\d3d9.dll
\Device\HarddiskVolume4\Program Files (x86)\Adobe\Adobe Creative Cloud\CEF\libcef.dll
\Device\HarddiskVolume4\Windows\SysWOW64\kernel32.dll
\Device\HarddiskVolume4\Windows\SysWOW64\ntdll.dll
Energierichtlinie:Aktiver Energieplan
Der derzeit verwendete Energieplan.
Planname
Ausbalanciert (OEM)
Plan-GUID
{381b4222-f694-41f0-9685-ff5bb260df2e}
Energierichtlinie:Energieplancharakter (Akkubetrieb)
Der Charakter des aktuellen Energieplans, wenn das System im Akkubetrieb ausgeführt wird.
Charakter
Ausbalanciert
Energierichtlinie:Videoqualität (Akkubetrieb)
Ermöglicht Windows Media Player, bei der Videowiedergabe die Qualität und die Energieeinsparung zu optimieren.
Qualitätsmodus
Videoqualität und Energieeinsparung ausbalancieren
Energierichtlinie:Energieplancharakter (Netzbetrieb)
Der Charakter des aktuellen Energieplans, wenn das System im Netzbetrieb ausgeführt wird.
Charakter
Ausbalanciert
Energierichtlinie:802.11-Energierichtlinie für Drahtlosverbindungen ist "Maximale Leistung" (Netzbetrieb)
Die aktuelle Energierichtlinie für 802.11-kompatible Drahtlosnetzwerkadapter ist nicht für die Verwendung von Energiesparmodi konfiguriert.
Energierichtlinie:Videoqualität (Netzbetrieb)
Ermöglicht Windows Media Player, bei der Videowiedergabe die Qualität und die Energieeinsparung zu optimieren.
Qualitätsmodus
Für hohe Videoqualität optimieren
Systemverfügbarkeitsanforderungen:Erfolgreiche Analyse
Die Analyse war erfolgreich. Es wurden keine Energieeffizienzprobleme festgestellt und keine Informationen zurückgegeben.
Akku:Akkuinformationen
Akku-ID
1F11LGC_LGCX863568
Hersteller
LGC_LGC
Seriennummer
1F11
Chemie
LION
Langfristig
1
Versiegelt
0
Zyklusanzahl
33
Vorgesehene Akkukapazität
42157
Letzte vollständige Aufladung
44209
Funktionen der Plattformenergieverwaltung:Unterstützte Standbystatus
Mithilfe von Standbystatus kann der Computer nach einer Zeit der Inaktivität in einen Energiesparmodus wechseln. Der S3-Standbystatus ist der standardmäßige Standbystatus für Windows-Plattformen. Im S3-Standbystatus verbraucht der Computer nur die Energie,
die notwendig ist, um den Arbeitsspeicherinhalt zu bewahren und die Arbeit mit dem Computer schnell fortsetzen zu können. Sehr wenige Plattformen unterstützen den S1- oder S2-Standbystatus.
S1-Standbymodus unterstützt
false
S2-Standbymodus unterstützt
false
S3-Standbymodus unterstützt
false
S4-Standbymodus unterstützt
true
Funktionen der Plattformenergieverwaltung:Unterstützung von Verbindungsstandby
Mit dem Verbindungsstandby kann der Computer in einen Stromsparmodus wechseln, in dem er immer eingeschaltet und verbunden ist. Der Verbindungsstandby wird soweit unterstützt anstelle der Systemstandbystatus verwendet.
Verbindungsstandby unterstützt
true
Funktionen der Plattformenergieverwaltung:Die adaptive Bildschirmhelligkeit wird unterstützt.
Dieser Computer ermöglicht die automatische Helligkeitsregelung der integrierten Anzeige durch Windows.
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
0
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
1
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
2
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
3
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Gerätetreiber:Erfolgreiche Analyse
Die Analyse war erfolgreich. Es wurden keine Energieeffizienzprobleme festgestellt und keine Informationen zurückgegeben. -
Satellite A - Wrong screen resolution in games
Hi,
I change the operation system from Windows Vista home to Windows 7 64bit , and I download the Windows driver but when I playing games it appear at 1024*768 pixel and my laptop have 1366*768 pixel.
If any body have a solution to this problem please helpHello
Unfortunately I think you must offer more details about your problem like exact notebook model number and all games that you play.
Important point is that the game must support the native screen resolution of your monitor, otherwise you are not able to use 1366*768 pixel. You should check this firstly!
Furthermore make sure that newest display driver from Toshiba is installed and update your DirectX version. -
Lower screen resolution on 6280?
I'm noticing that a lot of applications and games are designed for a low resolution screen. My 6280 has high resolution, so that apps take up only the upper left hand corner of the screen. Too tiny to read, really. Is there a way lower my screen resolution? Or is it that these games have to be resolution-aware? Thanks for any advice.
Hello.
You have no choice for this matter, I guess, and you must succumb playing your low-res games in this manner. As manta have said, there are programmers who are pretty adept at changing the resolution covered by the application depending on the screen's native resolution.
Cheers.
The world might be a better place if you were I. -
Hi,
I recently had to run diskwarrior to do some rebuilding on my machine but ever since the screen resolution seems to be lower than previously. This is particularly noticeable on photos.
I've been into preferences to check the screen is set to the highest setting, which it is, so I'm not sure why it has changed.
Can anyone help?
ThanksHave you tried setting the resolution to the lowest setting in System Preferences, and then switch it back to the lowest resolution?
If that doesn't work, try creating a new Colorsync profile and see if the problem lies there.
If none of these solutions work, I would say that you may have to do an erase and install of Mac OS X or at least look for a corrupted file. -
Satellite A500-17X: How to install Win XP mode for Win 7 64bit
I bought a Toshiba Satellite A500 17X Laptop recently.
Windows 7 Home Premium 64bit. I have since upgraded to Professional. I am trying to download and install the XP Mode from the Microsot website.
I have quit a few bits of software mostly Astronomy which worked in XP but will not install on Windows 7.
From the Microsoft web site i selected Professional 64bit from the drop down list.
When i tried installing the file a message popped up saying: +This is not a valid Win32 file+
So i downloaded the Professional 32bit file.
When i tried to install this the same message popped up. According to the videos on the Microsoft web site this should be easy.
Anyone know what i am doing wrong.
Thank You.
GreyhoundI too recently bought a Toshiba A500 17X laptop. Like you I also need to run some legacy XP programs that do not run under Win 7.
So, I found out that I must upgrade from Win 7 Home Premium to Win 7 Professional. But .... before parting with 100 quid or so I thought I would investigate a little.
At the Microsoft web site:-
http://www.microsoft.com/windows/virtual-pc/download.aspx
It explains what steps to take.
At Step 2 you can run a tool to determine if 'your PC hardware works with Windows XP Mode...' This hyperlink takes you to the Microsoft Hardware-Assisted Virtualization Tool where you can download a guide and the tool to see if the PC is up to it.
I did this and it seems the hardware is NOT up to the task, nor as far as I can determine is there a switch in the BIOS to allow this.
Don't think it matters whether Win 7 is 32-bit or 64-bit.
This is really not good enough for a laptop that cost £700. ............or am I wrong?
Patriot -
2 weeks ago when I switched on my pc (Windows XP) I had very poor screen resolution, which I was unable to fix other than by resetting to an earlier day. I also was having problems with McAffee saying that it couldn't access my pc to upload files. Eventually, I asked McAfee to sort the problem, which they did by taking control of my pc. I am now getting messages today saying that updates from McAffee have been uploaded satisfactorily. However, each time I now switch on my pc I get the same very poor screen resolution which I can only fix by resetting to a previous date.
Have you any ideas as to why this should be happening and more importantly how I can fix it.Hello davebeac!
Welcome to Firefox Support!
For your problem, what I'm reading from your post, the screen resolution has nothing to do with Firefox. Your resolution has to do with your computer graphics card. To fix this problem just do the following steps:
1.
1. Open Display in Control Panel.
2. On the Settings tab, under Screen resolution, drag the slider, and then click Apply.
3. When prompted to apply the settings, click OK. Your screen will turn black for a moment.
4. Once your screen resolution changes, you have 15 seconds to confirm the change. Click Yes to confirm the change; click No or do nothing to revert to your previous setting. -
Screen resolution on Win 7 set to 1920x1080 instead of 1920x1200 (MBP 17 early 2011)
After performing a SMC reset on my MacBook Pro 17 (early 2011), the screen resolution of my Windows 7 on the bootcamp partition was set to 1920x1080, instead of 1920x1200. On Control Panel, the option for the 1920x1200 resolution doesn't appear. How can I fix this? Reinstall BootCamp 3.2 64-bit? Thanks.
Try command-shift on boot up. If all else fails boot from your OS installer disk and run Repair Disk from Disk Utility.
-
Low screen resolution on my T400.
Maximum screen resolution on my new ThinkPad T400 with discrete graphics(windows 7 home premium) is only 1280x800, I was expecting it to to more higher.
Please advice on what to do.
ATI Mobility Radeon 3470 with 256MB
Thanks in advance.
Solved!
Go to Solution.IIRC, the choices were 1280x800 (WXGA) or 1440x900 (WXGA+ as mine is). W/ the CTO models you had to pick one when specifying the system.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество -
Satellite A500 - blue screen - BCCode:50
Hi
My satellite A500 shows a bluescreen with the following script on it shortly after starting up,
Can anyone advise what i should do?
Many thanks in advance
coinneach
Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7600.2.0.0.768.3
Locale ID: 2057
Additional information about the problem:
BCCode: 50
BCP1: FFFFF8800B7FD848
BCP2: 0000000000000001
BCP3: FFFFF880075EA624
BCP4: 0000000000000000
OS Version: 6_1_7600
Service Pack: 0_0
Product: 768_1
Files that help describe the problem:
C:\Windows\Minidump\012311-30654-01.dmp
C:\Users\Kenny\AppData\Local\Temp\WER-65052-0.sysdata.xmlHi
BSOD is always an painful issue because it can be related to different reasons;
It can be a hardware issue but it can be also an serious software problem.
So its not easy to say what cause this exactly
I had an BSOD in the past because my RAM was faulty.
I have replaced it and since than its ok.
The friend of mine has had an BSOD issue too. It was caused by graphic card driver.
Graphic card driver update helped.
The high temperature can be a reason as well so check if the temp is not too high.
The new OS installation might be a option too but this is your own decision -
Creating pdf contact sheets at screen resolution using aperture/photoshop
Can anyone advise me on how to create a pdf document of contact sheets- low resolution [72 screen res]that is less time consuming than the present work flow described below?
At present I export jpegs 450pxl 72dpi from aperture. create contact sheets in photoshop and then
create a pdf in photoshop. Average number of images per client is approx 800-1000,
The pdf I have created with aperture has a resolutuin of 300dpi- which is a large file to email etc. I have tried reimporting the 450pxl jpegs but aperture still creates the document at 300dpi.
Is it possible ...
1/. to solely use aperture to create low res pdf's
2/. If not is it possible to create an action in photoshop [or use automator] to speed up the process described above?
I do have a little experience using actions in photoshop but am by no means an experienced user.Awesome! I didnt even know aperture could do that
Now another quick question on this topic, if im using RAW files, does aperture need to convert the file to jpeg or tiff (like it does if you export version as jpeg)?
If it does, that may be a problem as it takes forever for aperture on my macbook to convert raws and save as jpegs, like a good minute or two per photo, and if i have 200odd photos....not good, people will crack it waiting and leave.
Or does it print as raw? Cause im pretty sure my printer (or any printer) can not print raw files. Will try it tonight on my printer but a heads up will be useful.
I could just shoot in hi-res jpeg, but id rather shoot raw incase they want a large poster size print etc.
Thanks. -
Nouveau driver gives very low screen resolution [SOLVED]
Hello.
I have a 1680x1050 monitor. I have just switched from nvidia to nouveau drivers.
At boot time (I have disabled the old framebuffer setting in grub's menu.lst) after a while I have a beautiful very high resolution console.
The problem is, I have very low resolutions in X.
[user@pc ~]$ xrandr
Screen 0: minimum 320 x 200, current 640 x 480, maximum 8192 x 8192
DVI-I-1 connected 640x480+0+0 (normal left inverted right x axis y axis) 474mm x 296mm
640x480 60.0*
720x400 70.1
VGA-1 disconnected (normal left inverted right x axis y axis)
I have this /etc/X11.xorg.conf file
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 28.0 - 33.0
VertRefresh 43.0 - 72.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nouveau"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
EndSubSection
EndSection
Section "InputClass"
Identifier "evdev keyboard catchall"
MatchIsKeyboard "on"
MatchDevicePath "/dev/input/event*"
Driver "evdev"
# Keyboard layouts
Option "XkbLayout" "us, el"
Option "XkbVariant" ",qwerty"
Option "XkbOptions" "grp:alt_shift_toggle, grp_led:scroll, terminate:ctrl_alt_bksp"
EndSection
This is /var/log/Xorg.0.log
[ 284.975]
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
[ 284.975]
X.Org X Server 1.10.3.901 (1.10.4 RC 1)
Release Date: 2011-07-29
[ 284.975] X Protocol Version 11, Revision 0
[ 284.975] Build Operating System: Linux 3.0.0-ARCH x86_64
[ 284.975] Current Operating System: Linux gandalf 3.0-ARCH #1 SMP PREEMPT Wed Aug 17 21:55:57 CEST 2011 x86_64
[ 284.975] Kernel command line: root=/dev/sda1 ro
[ 284.975] Build Date: 08 August 2011 08:24:13AM
[ 284.975]
[ 284.975] Current version of pixman: 0.22.2
[ 284.975] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 284.975] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 284.975] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Aug 25 19:11:02 2011
[ 284.975] (==) Using config file: "/etc/X11/xorg.conf"
[ 284.975] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 284.975] (==) ServerLayout "Layout0"
[ 284.975] (**) |-->Screen "Screen0" (0)
[ 284.975] (**) | |-->Monitor "Monitor0"
[ 284.976] (**) | |-->Device "Device0"
[ 284.976] (**) |-->Input Device "Keyboard0"
[ 284.976] (**) |-->Input Device "Mouse0"
[ 284.976] (==) Automatically adding devices
[ 284.976] (==) Automatically enabling devices
[ 284.976] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 284.976] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 284.976] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 284.976] (WW) Disabling Keyboard0
[ 284.976] (WW) Disabling Mouse0
[ 284.976] (II) Loader magic: 0x7d3620
[ 284.976] (II) Module ABI versions:
[ 284.976] X.Org ANSI C Emulation: 0.4
[ 284.976] X.Org Video Driver: 10.0
[ 284.976] X.Org XInput driver : 12.2
[ 284.976] X.Org Server Extension : 5.0
[ 284.977] (--) PCI: (0:2:0:0) 10de:0849:1849:0849 rev 162, Mem @ 0xf9000000/16777216, 0xc8000000/134217728, 0xc6000000/33554432, I/O @ 0x0000cc00/128, BIOS @ 0x????????/131072
[ 284.977] (--) PCI:*(0:3:0:0) 10de:0421:10b0:1401 rev 161, Mem @ 0xfc000000/16777216, 0xd0000000/268435456, 0xfa000000/33554432, I/O @ 0x0000dc00/128, BIOS @ 0x????????/131072
[ 284.977] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 284.977] (II) LoadModule: "extmod"
[ 284.977] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 284.977] (II) Module extmod: vendor="X.Org Foundation"
[ 284.977] compiled for 1.10.3.901, module version = 1.0.0
[ 284.977] Module class: X.Org Server Extension
[ 284.977] ABI class: X.Org Server Extension, version 5.0
[ 284.977] (II) Loading extension MIT-SCREEN-SAVER
[ 284.977] (II) Loading extension XFree86-VidModeExtension
[ 284.977] (II) Loading extension XFree86-DGA
[ 284.978] (II) Loading extension DPMS
[ 284.978] (II) Loading extension XVideo
[ 284.978] (II) Loading extension XVideo-MotionCompensation
[ 284.978] (II) Loading extension X-Resource
[ 284.978] (II) LoadModule: "dbe"
[ 284.978] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 284.978] (II) Module dbe: vendor="X.Org Foundation"
[ 284.978] compiled for 1.10.3.901, module version = 1.0.0
[ 284.978] Module class: X.Org Server Extension
[ 284.978] ABI class: X.Org Server Extension, version 5.0
[ 284.978] (II) Loading extension DOUBLE-BUFFER
[ 284.978] (II) LoadModule: "glx"
[ 284.978] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 284.978] (II) Module glx: vendor="X.Org Foundation"
[ 284.978] compiled for 1.10.3.901, module version = 1.0.0
[ 284.978] ABI class: X.Org Server Extension, version 5.0
[ 284.978] (==) AIGLX enabled
[ 284.978] (II) Loading extension GLX
[ 284.978] (II) LoadModule: "record"
[ 284.978] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 284.978] (II) Module record: vendor="X.Org Foundation"
[ 284.978] compiled for 1.10.3.901, module version = 1.13.0
[ 284.978] Module class: X.Org Server Extension
[ 284.978] ABI class: X.Org Server Extension, version 5.0
[ 284.978] (II) Loading extension RECORD
[ 284.978] (II) LoadModule: "dri"
[ 284.978] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 284.979] (II) Module dri: vendor="X.Org Foundation"
[ 284.979] compiled for 1.10.3.901, module version = 1.0.0
[ 284.979] ABI class: X.Org Server Extension, version 5.0
[ 284.979] (II) Loading extension XFree86-DRI
[ 284.979] (II) LoadModule: "dri2"
[ 284.979] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 284.979] (II) Module dri2: vendor="X.Org Foundation"
[ 284.979] compiled for 1.10.3.901, module version = 1.2.0
[ 284.979] ABI class: X.Org Server Extension, version 5.0
[ 284.979] (II) Loading extension DRI2
[ 284.979] (II) LoadModule: "nouveau"
[ 284.979] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 284.979] (II) Module nouveau: vendor="X.Org Foundation"
[ 284.979] compiled for 1.10.3, module version = 0.0.16
[ 284.979] Module class: X.Org Video Driver
[ 284.979] ABI class: X.Org Video Driver, version 10.0
[ 284.979] (II) NOUVEAU driver
[ 284.979] (II) NOUVEAU driver for NVIDIA chipset families :
[ 284.979] RIVA TNT (NV04)
[ 284.979] RIVA TNT2 (NV05)
[ 284.979] GeForce 256 (NV10)
[ 284.979] GeForce 2 (NV11, NV15)
[ 284.979] GeForce 4MX (NV17, NV18)
[ 284.979] GeForce 3 (NV20)
[ 284.979] GeForce 4Ti (NV25, NV28)
[ 284.979] GeForce FX (NV3x)
[ 284.979] GeForce 6 (NV4x)
[ 284.979] GeForce 7 (G7x)
[ 284.979] GeForce 8 (G8x)
[ 284.979] GeForce GTX 200 (NVA0)
[ 284.979] GeForce GTX 400 (NVC0)
[ 284.979] (++) using VT number 7
[ 284.982] drmOpenDevice: node name is /dev/dri/card0
[ 284.982] drmOpenDevice: open result is 7, (OK)
[ 284.982] drmOpenByBusid: Searching for BusID pci:0000:03:00.0
[ 284.982] drmOpenDevice: node name is /dev/dri/card0
[ 284.982] drmOpenDevice: open result is 7, (OK)
[ 284.982] drmOpenByBusid: drmOpenMinor returns 7
[ 284.982] drmOpenByBusid: drmGetBusid reports pci:0000:03:00.0
[ 284.982] (II) [drm] nouveau interface version: 0.0.16
[ 284.982] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 284.982] (II) Loading sub module "dri"
[ 284.982] (II) LoadModule: "dri"
[ 284.982] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 284.982] (II) Module dri: vendor="X.Org Foundation"
[ 284.982] compiled for 1.10.3.901, module version = 1.0.0
[ 284.982] ABI class: X.Org Server Extension, version 5.0
[ 284.982] (II) NOUVEAU(0): Loaded DRI module
[ 284.982] drmOpenDevice: node name is /dev/dri/card0
[ 284.982] drmOpenDevice: open result is 8, (OK)
[ 284.982] drmOpenDevice: node name is /dev/dri/card0
[ 284.982] drmOpenDevice: open result is 8, (OK)
[ 284.982] drmOpenByBusid: Searching for BusID pci:0000:03:00.0
[ 284.982] drmOpenDevice: node name is /dev/dri/card0
[ 284.982] drmOpenDevice: open result is 8, (OK)
[ 284.982] drmOpenByBusid: drmOpenMinor returns 8
[ 284.982] drmOpenByBusid: drmGetBusid reports pci:0000:03:00.0
[ 284.982] (II) [drm] DRM interface version 1.4
[ 284.982] (II) [drm] DRM open master succeeded.
[ 284.982] (--) NOUVEAU(0): Chipset: "NVIDIA NV86"
[ 284.982] (**) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[ 284.982] (==) NOUVEAU(0): RGB weight 888
[ 284.982] (==) NOUVEAU(0): Default visual is TrueColor
[ 284.983] (==) NOUVEAU(0): Using HW cursor
[ 284.983] (==) NOUVEAU(0): GLX sync to VBlank disabled.
[ 284.983] (==) NOUVEAU(0): Page flipping enabled
[ 285.087] (II) NOUVEAU(0): Output DVI-I-1 using monitor section Monitor0
[ 285.184] (II) NOUVEAU(0): Output VGA-1 has no monitor section
[ 285.288] (II) NOUVEAU(0): EDID for output DVI-I-1
[ 285.288] (II) NOUVEAU(0): Manufacturer: GSM Model: 566f Serial#: 351988
[ 285.288] (II) NOUVEAU(0): Year: 2008 Week: 4
[ 285.288] (II) NOUVEAU(0): EDID Version: 1.3
[ 285.288] (II) NOUVEAU(0): Digital Display Input
[ 285.288] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 49 vert.: 32
[ 285.288] (II) NOUVEAU(0): Gamma: 2.20
[ 285.288] (II) NOUVEAU(0): DPMS capabilities: StandBy Suspend Off
[ 285.288] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 285.288] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 285.288] (II) NOUVEAU(0): redX: 0.653 redY: 0.341 greenX: 0.231 greenY: 0.666
[ 285.288] (II) NOUVEAU(0): blueX: 0.150 blueY: 0.062 whiteX: 0.313 whiteY: 0.329
[ 285.288] (II) NOUVEAU(0): Supported established timings:
[ 285.288] (II) NOUVEAU(0): 720x400@70Hz
[ 285.288] (II) NOUVEAU(0): 640x480@60Hz
[ 285.288] (II) NOUVEAU(0): 640x480@75Hz
[ 285.288] (II) NOUVEAU(0): 800x600@56Hz
[ 285.288] (II) NOUVEAU(0): 800x600@60Hz
[ 285.288] (II) NOUVEAU(0): 800x600@75Hz
[ 285.288] (II) NOUVEAU(0): 832x624@75Hz
[ 285.288] (II) NOUVEAU(0): 1024x768@60Hz
[ 285.288] (II) NOUVEAU(0): 1024x768@75Hz
[ 285.288] (II) NOUVEAU(0): 1280x1024@75Hz
[ 285.288] (II) NOUVEAU(0): 1152x864@75Hz
[ 285.288] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 285.288] (II) NOUVEAU(0): Supported standard timings:
[ 285.288] (II) NOUVEAU(0): #0: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 285.288] (II) NOUVEAU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 285.288] (II) NOUVEAU(0): #2: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 285.288] (II) NOUVEAU(0): #3: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 285.288] (II) NOUVEAU(0): Supported detailed timing:
[ 285.288] (II) NOUVEAU(0): clock: 119.0 MHz Image Size: 474 x 296 mm
[ 285.288] (II) NOUVEAU(0): h_active: 1680 h_sync: 1728 h_sync_end 1760 h_blank_end 1840 h_border: 0
[ 285.288] (II) NOUVEAU(0): v_active: 1050 v_sync: 1053 v_sync_end 1059 v_blanking: 1080 v_border: 0
[ 285.288] (II) NOUVEAU(0): Supported detailed timing:
[ 285.288] (II) NOUVEAU(0): clock: 146.2 MHz Image Size: 474 x 296 mm
[ 285.288] (II) NOUVEAU(0): h_active: 1680 h_sync: 1784 h_sync_end 1960 h_blank_end 2240 h_border: 0
[ 285.288] (II) NOUVEAU(0): v_active: 1050 v_sync: 1053 v_sync_end 1059 v_blanking: 1089 v_border: 0
[ 285.289] (II) NOUVEAU(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 155 MHz
[ 285.289] (II) NOUVEAU(0): Monitor name: L227W
[ 285.289] (II) NOUVEAU(0): EDID (in hex):
[ 285.289] (II) NOUVEAU(0): 00ffffffffffff001e6d6f56f45e0500
[ 285.289] (II) NOUVEAU(0): 04120103ea312078ea56b5a7573baa26
[ 285.289] (II) NOUVEAU(0): 0f5054a76b80950081808140714f0101
[ 285.289] (II) NOUVEAU(0): 0101010101017c2e90a0601a1e403020
[ 285.289] (II) NOUVEAU(0): 3600da281100001a21399030621a2740
[ 285.289] (II) NOUVEAU(0): 68b03600da281100001c000000fd0038
[ 285.289] (II) NOUVEAU(0): 4b1e530f000a202020202020000000fc
[ 285.289] (II) NOUVEAU(0): 004c323237570a202020202020200063
[ 285.289] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 285.289] (II) NOUVEAU(0): Using hsync ranges from config file
[ 285.289] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 285.289] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 285.289] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 285.289] (II) NOUVEAU(0): Not using mode "1680x1050" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1680x1050" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1280x1024" (vrefresh out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1280x1024" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1440x900" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1280x960" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1152x864" (vrefresh out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1024x768" (vrefresh out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "1024x768" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "832x624" (vrefresh out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "800x600" (vrefresh out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "800x600" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "800x600" (hsync out of range)
[ 285.289] (II) NOUVEAU(0): Not using mode "640x480" (vrefresh out of range)
[ 285.289] (II) NOUVEAU(0): Printing probed modes for output DVI-I-1
[ 285.289] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 285.289] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 285.386] (II) NOUVEAU(0): EDID for output VGA-1
[ 285.386] (II) NOUVEAU(0): Output DVI-I-1 connected
[ 285.386] (II) NOUVEAU(0): Output VGA-1 disconnected
[ 285.386] (II) NOUVEAU(0): Using fuzzy aspect match for initial modes
[ 285.386] (II) NOUVEAU(0): Output DVI-I-1 using initial mode 640x480
[ 285.386] (II) NOUVEAU(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 285.386] (--) NOUVEAU(0): Virtual size is 640x480 (pitch 0)
[ 285.386] (**) NOUVEAU(0): Driver mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
[ 285.386] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 285.386] (**) NOUVEAU(0): Driver mode "720x400": 28.3 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.1 Hz
[ 285.386] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 285.387] (**) NOUVEAU(0): Display dimensions: (490, 320) mm
[ 285.387] (**) NOUVEAU(0): DPI set to (33, 38)
[ 285.387] (II) Loading sub module "fb"
[ 285.387] (II) LoadModule: "fb"
[ 285.387] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 285.387] (II) Module fb: vendor="X.Org Foundation"
[ 285.387] compiled for 1.10.3.901, module version = 1.0.0
[ 285.387] ABI class: X.Org ANSI C Emulation, version 0.4
[ 285.387] (II) Loading sub module "exa"
[ 285.387] (II) LoadModule: "exa"
[ 285.387] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 285.387] (II) Module exa: vendor="X.Org Foundation"
[ 285.387] compiled for 1.10.3.901, module version = 2.5.0
[ 285.387] ABI class: X.Org Video Driver, version 10.0
[ 285.387] (II) Loading sub module "shadowfb"
[ 285.387] (II) LoadModule: "shadowfb"
[ 285.387] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[ 285.387] (II) Module shadowfb: vendor="X.Org Foundation"
[ 285.387] compiled for 1.10.3.901, module version = 1.0.0
[ 285.387] ABI class: X.Org ANSI C Emulation, version 0.4
[ 285.387] (--) Depth 24 pixmap format is 32 bpp
[ 285.391] (II) NOUVEAU(0): Opened GPU channel 2
[ 285.391] (II) NOUVEAU(0): [DRI2] Setup complete
[ 285.391] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau
[ 285.391] (II) NOUVEAU(0): GART: 512MiB available
[ 285.393] (II) NOUVEAU(0): GART: Allocated 16MiB as a scratch buffer
[ 285.393] (II) EXA(0): Driver allocated offscreen pixmaps
[ 285.393] (II) EXA(0): Driver registered support for the following operations:
[ 285.393] (II) Solid
[ 285.393] (II) Copy
[ 285.393] (II) Composite (RENDER acceleration)
[ 285.393] (II) UploadToScreen
[ 285.393] (II) DownloadFromScreen
[ 285.393] (==) NOUVEAU(0): Backing store disabled
[ 285.393] (==) NOUVEAU(0): Silken mouse enabled
[ 285.393] (II) NOUVEAU(0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video.
[ 285.393] (II) NOUVEAU(0): [XvMC] Extension initialized.
[ 285.393] (**) NOUVEAU(0): DPMS enabled
[ 285.393] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 285.393] (--) RandR disabled
[ 285.393] (II) Initializing built-in extension Generic Event Extension
[ 285.393] (II) Initializing built-in extension SHAPE
[ 285.393] (II) Initializing built-in extension MIT-SHM
[ 285.393] (II) Initializing built-in extension XInputExtension
[ 285.393] (II) Initializing built-in extension XTEST
[ 285.393] (II) Initializing built-in extension BIG-REQUESTS
[ 285.393] (II) Initializing built-in extension SYNC
[ 285.393] (II) Initializing built-in extension XKEYBOARD
[ 285.393] (II) Initializing built-in extension XC-MISC
[ 285.393] (II) Initializing built-in extension SECURITY
[ 285.394] (II) Initializing built-in extension XINERAMA
[ 285.394] (II) Initializing built-in extension XFIXES
[ 285.394] (II) Initializing built-in extension RENDER
[ 285.394] (II) Initializing built-in extension RANDR
[ 285.394] (II) Initializing built-in extension COMPOSITE
[ 285.394] (II) Initializing built-in extension DAMAGE
[ 285.407] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 285.407] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 285.407] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 285.407] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 285.407] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 285.407] (II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/nouveau_dri.so
[ 285.407] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 285.408] (II) NOUVEAU(0): NVEnterVT is called.
[ 285.437] (II) NOUVEAU(0): Setting screen physical size to 169 x 127
[ 285.437] resize called 640 480
[ 285.563] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 285.563] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 285.563] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 285.563] (II) LoadModule: "evdev"
[ 285.564] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.564] (II) Module evdev: vendor="X.Org Foundation"
[ 285.564] compiled for 1.10.0, module version = 2.6.0
[ 285.564] Module class: X.Org XInput Driver
[ 285.564] ABI class: X.Org XInput driver, version 12.2
[ 285.564] (II) Using input driver 'evdev' for 'Power Button'
[ 285.564] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.564] (**) Power Button: always reports core events
[ 285.564] (**) Power Button: Device: "/dev/input/event1"
[ 285.564] (--) Power Button: Found keys
[ 285.564] (II) Power Button: Configuring as keyboard
[ 285.564] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[ 285.564] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 285.564] (**) Option "xkb_rules" "evdev"
[ 285.564] (**) Option "xkb_model" "evdev"
[ 285.564] (**) Option "xkb_layout" "us, el"
[ 285.564] (**) Option "xkb_variant" ",qwerty"
[ 285.564] (**) Option "xkb_options" "grp:alt_shift_toggle, grp_led:scroll, terminate:ctrl_alt_bksp"
[ 285.590] (EE) Error loading keymap /var/lib/xkb/server-0.xkm
[ 285.590] (EE) XKB: Failed to load keymap. Loading default keymap instead.
[ 285.622] (II) config/udev: Adding input device Video Bus (/dev/input/event2)
[ 285.622] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 285.622] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 285.622] (II) Using input driver 'evdev' for 'Video Bus'
[ 285.622] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.622] (**) Video Bus: always reports core events
[ 285.622] (**) Video Bus: Device: "/dev/input/event2"
[ 285.622] (--) Video Bus: Found keys
[ 285.622] (II) Video Bus: Configuring as keyboard
[ 285.622] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:19/LNXVIDEO:00/input/input2/event2"
[ 285.622] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[ 285.622] (**) Option "xkb_rules" "evdev"
[ 285.622] (**) Option "xkb_model" "evdev"
[ 285.622] (**) Option "xkb_layout" "us, el"
[ 285.622] (**) Option "xkb_variant" ",qwerty"
[ 285.622] (**) Option "xkb_options" "grp:alt_shift_toggle, grp_led:scroll, terminate:ctrl_alt_bksp"
[ 285.623] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 285.623] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 285.623] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 285.623] (II) Using input driver 'evdev' for 'Power Button'
[ 285.623] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.623] (**) Power Button: always reports core events
[ 285.623] (**) Power Button: Device: "/dev/input/event0"
[ 285.623] (--) Power Button: Found keys
[ 285.623] (II) Power Button: Configuring as keyboard
[ 285.623] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
[ 285.623] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 285.623] (**) Option "xkb_rules" "evdev"
[ 285.623] (**) Option "xkb_model" "evdev"
[ 285.623] (**) Option "xkb_layout" "us, el"
[ 285.623] (**) Option "xkb_variant" ",qwerty"
[ 285.623] (**) Option "xkb_options" "grp:alt_shift_toggle, grp_led:scroll, terminate:ctrl_alt_bksp"
[ 285.626] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event4)
[ 285.626] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[ 285.626] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[ 285.626] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
[ 285.626] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.626] (**) Microsoft Wired Keyboard 600: always reports core events
[ 285.626] (**) Microsoft Wired Keyboard 600: Device: "/dev/input/event4"
[ 285.626] (--) Microsoft Wired Keyboard 600: Found keys
[ 285.626] (II) Microsoft Wired Keyboard 600: Configuring as keyboard
[ 285.626] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input4/event4"
[ 285.626] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD)
[ 285.626] (**) Option "xkb_rules" "evdev"
[ 285.626] (**) Option "xkb_model" "evdev"
[ 285.626] (**) Option "xkb_layout" "us, el"
[ 285.626] (**) Option "xkb_variant" ",qwerty"
[ 285.626] (**) Option "xkb_options" "grp:alt_shift_toggle, grp_led:scroll, terminate:ctrl_alt_bksp"
[ 285.627] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event5)
[ 285.627] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[ 285.627] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[ 285.627] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
[ 285.627] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.627] (**) Microsoft Wired Keyboard 600: always reports core events
[ 285.627] (**) Microsoft Wired Keyboard 600: Device: "/dev/input/event5"
[ 285.627] (--) Microsoft Wired Keyboard 600: Found 1 mouse buttons
[ 285.627] (--) Microsoft Wired Keyboard 600: Found scroll wheel(s)
[ 285.627] (--) Microsoft Wired Keyboard 600: Found relative axes
[ 285.627] (--) Microsoft Wired Keyboard 600: Found absolute axes
[ 285.627] (--) Microsoft Wired Keyboard 600: Found x and y absolute axes
[ 285.627] (--) Microsoft Wired Keyboard 600: Found keys
[ 285.627] (II) Microsoft Wired Keyboard 600: Configuring as mouse
[ 285.627] (II) Microsoft Wired Keyboard 600: Configuring as keyboard
[ 285.627] (II) Microsoft Wired Keyboard 600: Adding scrollwheel support
[ 285.627] (**) Microsoft Wired Keyboard 600: YAxisMapping: buttons 4 and 5
[ 285.627] (**) Microsoft Wired Keyboard 600: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 285.627] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.1/input/input5/event5"
[ 285.627] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD)
[ 285.627] (**) Option "xkb_rules" "evdev"
[ 285.627] (**) Option "xkb_model" "evdev"
[ 285.627] (**) Option "xkb_layout" "us, el"
[ 285.627] (**) Option "xkb_variant" ",qwerty"
[ 285.627] (**) Option "xkb_options" "grp:alt_shift_toggle, grp_led:scroll, terminate:ctrl_alt_bksp"
[ 285.627] (EE) Microsoft Wired Keyboard 600: failed to initialize for relative axes.
[ 285.627] (WW) Microsoft Wired Keyboard 600: found 37 axes, limiting to 36.
[ 285.627] (II) Microsoft Wired Keyboard 600: initialized for absolute axes.
[ 285.628] (**) Microsoft Wired Keyboard 600: (accel) keeping acceleration scheme 1
[ 285.628] (**) Microsoft Wired Keyboard 600: (accel) acceleration profile 0
[ 285.628] (**) Microsoft Wired Keyboard 600: (accel) acceleration factor: 2.000
[ 285.628] (**) Microsoft Wired Keyboard 600: (accel) acceleration threshold: 4
[ 285.628] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/js0)
[ 285.628] (II) No input driver/identifier specified (ignoring)
[ 285.629] (II) config/udev: Adding input device Microsoft Microsoft Basic Optical Mouse v2.0 (/dev/input/event6)
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : Applying InputClass "evdev pointer catchall"
[ 285.629] (II) Using input driver 'evdev' for 'Microsoft Microsoft Basic Optical Mouse v2.0 '
[ 285.629] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : always reports core events
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : Device: "/dev/input/event6"
[ 285.629] (--) Microsoft Microsoft Basic Optical Mouse v2.0 : Found 3 mouse buttons
[ 285.629] (--) Microsoft Microsoft Basic Optical Mouse v2.0 : Found scroll wheel(s)
[ 285.629] (--) Microsoft Microsoft Basic Optical Mouse v2.0 : Found relative axes
[ 285.629] (--) Microsoft Microsoft Basic Optical Mouse v2.0 : Found x and y relative axes
[ 285.629] (II) Microsoft Microsoft Basic Optical Mouse v2.0 : Configuring as mouse
[ 285.629] (II) Microsoft Microsoft Basic Optical Mouse v2.0 : Adding scrollwheel support
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : YAxisMapping: buttons 4 and 5
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 285.629] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:04.0/usb4/4-3/4-3:1.0/input/input6/event6"
[ 285.629] (II) XINPUT: Adding extended input device "Microsoft Microsoft Basic Optical Mouse v2.0 " (type: MOUSE)
[ 285.629] (II) Microsoft Microsoft Basic Optical Mouse v2.0 : initialized for relative axes.
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : (accel) keeping acceleration scheme 1
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : (accel) acceleration profile 0
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : (accel) acceleration factor: 2.000
[ 285.629] (**) Microsoft Microsoft Basic Optical Mouse v2.0 : (accel) acceleration threshold: 4
[ 285.629] (II) config/udev: Adding input device Microsoft Microsoft Basic Optical Mouse v2.0 (/dev/input/mouse0)
[ 285.629] (II) No input driver/identifier specified (ignoring)
[ 285.636] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 285.636] (II) No input driver/identifier specified (ignoring)
[ 285.753] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 285.753] (II) NOUVEAU(0): Using hsync ranges from config file
[ 285.753] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 285.753] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 285.753] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 285.753] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 291.096] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 291.096] (II) NOUVEAU(0): NVLeaveVT is called.
[ 418.665] (II) AIGLX: Resuming AIGLX clients after VT switch
[ 418.665] (II) NOUVEAU(0): NVEnterVT is called.
[ 418.794] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 418.794] (II) NOUVEAU(0): Using hsync ranges from config file
[ 418.794] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 418.794] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 418.794] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 418.794] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 423.560] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 423.560] (II) NOUVEAU(0): Using hsync ranges from config file
[ 423.560] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 423.560] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 423.560] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 423.560] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 423.762] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 423.762] (II) NOUVEAU(0): Using hsync ranges from config file
[ 423.762] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 423.762] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 423.762] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 423.762] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 423.984] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 423.984] (II) NOUVEAU(0): Using hsync ranges from config file
[ 423.984] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 423.984] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 423.984] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 423.984] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 428.608] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 428.608] (II) NOUVEAU(0): Using hsync ranges from config file
[ 428.608] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 428.608] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 428.608] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 428.608] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 438.386] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 438.386] (II) NOUVEAU(0): NVLeaveVT is called.
[ 2748.085] (II) AIGLX: Resuming AIGLX clients after VT switch
[ 2748.085] (II) NOUVEAU(0): NVEnterVT is called.
[ 2748.217] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 2748.217] (II) NOUVEAU(0): Using hsync ranges from config file
[ 2748.217] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 2748.217] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 2748.217] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2748.217] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2750.536] (II) NOUVEAU(0): EDID vendor "GSM", prod id 22127
[ 2750.536] (II) NOUVEAU(0): Using hsync ranges from config file
[ 2750.536] (II) NOUVEAU(0): Using vrefresh ranges from config file
[ 2750.536] (II) NOUVEAU(0): Printing DDC gathered Modelines:
[ 2750.536] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1680x1050"x0.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2750.536] (II) NOUVEAU(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
Last edited by vega (2011-08-25 17:09:12)keyboard and mouse are now auto-detected. Do you have xf86-input-evdev installed? If so, you do not need to explicitly set the drivers for keyboard and mouse in xorg.conf. You can try it out if you like.
Maybe you are looking for
-
Skype Online Number is not working!!!!!!
Hello, I've recently renewed my online number subscription and none of my friends of family can get hold of me. I'm really disappointed! My skype number is +1[edited for privacy]. This number does not work at all - can you please advise me asap - is
-
I wonder what is included in the log files?
My application generates 1G log files per day. when I use logmnr to analyze the log files, I find that 2000 rows which is performed by my application user is in the v$logmnr_contents view. And 55000 rows which is performed by the Oracle sys user. In
-
Sharing DV video on externl HD between Mac & XP
Hi, I tried finding a post regarding this already but I'm still unclear. I don't know alot about media formats and if different OSs store them differently. My situation is: 1. I have an external HD (320gb) and I created 2 partitions, one for mac and
-
When does the configuration get locked for changes in sales order?
Hi Experts, I will really appreciate your help me in resolving this issue. Our client had sales order having BOM item with several sub items. Here we found that the user was not able to make changes to the Characterstic Value of one of the variant. T
-
Im trying to populate through odbc certain fields on the form, [ex. patient_id, firstname, last name, address, etc] which must change when primary/unique field [hence patient_id] is updated. Relationship is dictated by default from db and is picked u