Satellite C50-A-157 Sandisk USB won't work in Recovery Media Centre

I can't get Sandisk Cruzer USB to work in Recovery Media Centre. Have tried formatting but no luck.
I read on another Toshiba forum that Sandisk USBs don't work and that you have to use a different brand.
Anyone know if that's true?
Thanks

To be honest I dont think that all Sandisk USB flash memory stick dont work in connection with Recovery Media Creator. But of course due to some compatibility issue between the device and software, it could be possible that an USB flash memory stick would not be recognized.
I never experienced such problems with my Recovery Media Creator software.
I could create a recovery medium using two different USB sticks from two different manufacturers. One of them was a flash memory stick from SanDisk.

Similar Messages

Satellite C50-A-157 - Unable to use touchpad without holding left button

I know very little about my Satellite C50-A-157 . Run on Windows 8. I am main /admin user and all of a sudden I am unable to move the mouse/cursor.. only way it seems to let me, is if I hold the left hand botton (bottom of mouse pad) down at same time, then it moves around.
But then high-lights everything.
I have tried pressing FN+F5 at same time (nothing happens) even taken battery out of back (again does not solve issue) the MOuse/arrow is just frozen on the page.. this does not happen in my partners profile, (he is another user) the mouse seems to work fine..
I thought it was that the mouse pad, had worn out (as is shiny now) but this does not explain why it only happens under my profile/user, not his?
If anyone can offer any help, much appreciated... I only stumbled across the fact, it lets me use it (if I hold in left button at same time)
Also have tried the 'Sticky keys' shift x5, again this does not do anything or clear this problem.
And have gone into control panel usinw Windows+ X and gone into troubleshooting, again, not solved the problem.

.. this does not happen in my partners profile, (he is another user) the mouse seems to work fine..
Since the touchpad is still working using another user profile, I guess there must be only some software conflict.
Usually you can enable or disable the touchpad pressing F5 (or FN+F5) but you already tried this combination and this did not enable the touchpad…
So from my point of few you should simple uninstall the touchpad driver and after you have downloaded the newest touchpad driver package from Toshiba EU driver page, unzip the package and perform new touchpad driver installation…
After the installation has been finished, restart the notebook…
Good luck

Touchpad Problems on my Satellite C50-A-157

Hi, I have been having some problems with the touchpad on my *Toshiba Satellite C50-A-157* laptop.
I use windows 8, and i have had my laptop for a couple of weeks, but all vof a sudden,
I can only use the touchpad and operate the cursor when i have either of the mouse buttons held down.
I have been having to use the "Tab" key and the "Arrow Keys" to navigate through menus and options.
The *F5* key does not work and i have already tried updating/reinstalling the device drivers. Troubleshooting does not seem to work either.
However, whenever i have not got the mouse button pressed down, and the sursor is not movning, when i move my finger up and down on the touchpad, it will navigate through the vertical series of options closest to the left edge of the screen.
For example, in the windows 8 start menu, the mouse will be stationary in the middle of the screen, but when i move my finger up and down on the mouse pad, it seems to scroll through the tiles on the left of the menu, highlighting each one on the way up or down.
I realise this is quite a long, boring post, so thanks for reading this far and any help/suggestions you can give will be greatly appreciated, thanks.

Hi
In my opinion this isn't software realted issue.
Looks like a strange touchpad module problem but of course the notebook should be recovered to factory settings before talking about an hardware problem
Please post some feedback after the notebook has been set to factory settings.
In case the touchpad would not work even using factory settings, you should contact the service in order to check the hardware.

Cant get my Satellite C50-A-157 to start up

Hi folks I've got a Toshiba satellite C50-A-157, only three weeks old. It wouldn't connect to the internet last night, kept saying it couldn't display the page. Then the cursor froze and the touch pad wouldn't respond. I attached the mouse and eventually it responded to that. Still wouldn't let me online so decided I'd do a system restore. It went on for ages and nothing seemed to be going on, I had to go out so had to power it off. Tried to get back into it today but all the screen is doing is flickering between black and grey.
Toshiba offices are shut so was wondering if anyone can help me out? My knowledge is quite basic so all help would be appreciated!

It sounds pretty problematic now. I don't know if Ive understand you right but Im afraid you have interrupter recovery image installation and now you in the middle of nowhere.
To be honest I don't understand why your display is flickering now.
What to do now? I presume you didnt create recovery media but if you have it try to install recovery image again. If you don't have it either you must order one on https://backupmedia.toshiba.eu/landing.aspx or contact nearest Toshiba service provider in your country and ask for help.

When I import a video I recorded to my laptop from my Iphone 5c it won't play on window media centre or vec or any medium. Please help??? It plays perfect on the phone.

When I import a video I recorded to my laptop from my Iphone 5c it won't play on window media centre or vec or any medium. Please help??? It plays perfect on the phone.

The format from the phone is :
h.264 encoded video, AAC audio. Both standards of MPEG 4.
You need Windows Media Player version 12 or above to play MP4 (or add the codecs to your current version).

Satellite C50-A-138 - All USB ports have failed

Hi
I am having a major issue with my Satellite C50-A-138.
The card reader has never worked, and one by one the USB ports have one by one stopped working.
I can connect my phone to all of them, and it will charge.
But I can't plug any device into the ports and have the laptop recognise them at all.
So far I have tried the following;
Disabling and enabling each port
Uninstalling and reinstalling
Checking for updates
Refreshing windows 8
Reinstalling windows 8
Regedit HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\UsbFlags
Regedit HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\usbhub
Downloading hotfix
Is there anything else that I can do to make them work again?

>...I did a full reinstall without settings
What do you mean without settings?
Anyway, try please to install some drive manually just to see if this will help.
- Chipset Utility
- Storage driver
- Card Reader Controller

USB won´t work with Canon software

Since the last couple of OS updates the USB ports on both my iBook G4 and G5 Dual(older model) won´t recognise Canon´s Digital Photo Professional`s Capture utility. Since this is the only software that can control the aperture,shutter speed, ISO etc. from the computer - it is really important to me.Can anyone please give me advice how to get rid of the updates?
Thanks
Mikael
G5 Mac OS X (10.4.8)

I am also running Windows 98SE as one of my operating systems. I had a heck of a time getting USB 2 to work, but here's how you do it: Put the CD Driver and Utilities Disk in your CD/DVD drive. Go to USB\USB20\Win9x-ME\Intel. That's where the inf is that you need.
You will have 2 USB entries under your Device Manager in Windows 98SE. If you have a yellow ! on your enhanced controller, point it to where I said and it will update the drivers in your system. This worked for me.
I'm attaching an Orangeware driver link that you can download and install first. Then update the driver after reboot and point it to the location above
http://www.orangemicro.com/bin/USB2/Setup.exe
After your update you will see an Intel Ehhanced USB 2.0 Controller and a USB 2.0 Root Hub under the top entry USB set under Device Manager.

Satellite C50-B-14Z - Wi-Fi does not work properly

I've bought my laptop 1 week ago (Satellite C50-B-14Z), but Wi-Fi is not working properly. Most of the time, it looks like it's connected to my network without any problem. However, It does not work, I can't surf the web.
The router is new and all the conection has been checked by a staff member from the internet company.
What can i do? All software is updated.
Thanks.

As mentioned by previous user; first of all you should check if the notebooks internet connection would work using the LAN.
In case you will be able to connect to internet using LAN, you should check the WLan settings.
For example: I would recommend you to disable the WLan encryption (within the router configuration menu) and to test the WLan connection to an open (not secured) wireless LAN.
Of course this should be done only for testing purposes.
In case the connection would work, test different kind of encryption (WPA/WPA2 AES TKIP)

USB won't work after I unplugged without disconnecting now won't recognize any USB devices?

I put my Sandisk memory stick in to take some files off , i forgot to disconnect it properly so i plugged it back in and now it wont recognize any memory sticks i put in ? How do i fix it ?

Hello there, hales07.
The following Knowledge Base articles provide some good recommendations:
OS X Mavericks: If a USB device isn’t working
http://support.apple.com/kb/PH13876
You may also want to try an SMC Reset:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/ph14222
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Bootcamp windows 7 usb won't work

I have a Macbook Pro 9,1 (mid 2012) non-retina 15". I have recently installed Windows 7 Ultimate SP1 64-bit. The bootcamp version that I used was 5.1.5621.
Everything seems to be running properly, my keyboard (including apple buttons), trackpad, etc. The problem is my USB ports. Nothing I connect to them functions at all. My mouse, external HD, and USB flash drive are not recognized by Windows at all. Only the external HD seem to even get power. My mouse functioned fine during the Windows install and is lit up until about halfway through the "Setting up Windows" boot screen. After that the power is cut to it and will no longer function.
I have uninstalled and reinstalled bootcamp twice now, but nothing changes. I have to use a Microsoft uninstall fixer because when I try to uninstall bootcamp from the uninstall screen, I only get "change" and "repair" as options. I tried to repair as well, but after it finishes and my computer reboots, nothing is different. I am unsure if there is an installation issue because I can't easily uninstall it or if bootcamp just naturally works that way.
Everything works perfectly on Mavericks.

Glad you got it solved, BTW there is a Boot Camp forum if you ever need it. You can find it at:
http://discussions.apple.com/category.jspa?categoryID=237
Roger

Satellite L50-B-281 - WiFi Driver won't work

Hi everybody,
I have a problem I just can't find a solution to
I've bought a L50-B-81 without OS, because I have a free W7 licence.
I used the Driver Download at Toshiba to look for the Drivers.
For my model (PSKTCE) I was presented two Drivers one for Broadcom and one for Aatheros.
The Broadcom installer did not do anything so I presume, I don't have Broadcom Hardware.
The Atheros driver installed only Bluetooth.
Is there an easy way to determine what the Hardware inside is?
The device Manager, where the not working devices are marked with this triangle warning sign, tells me it does not know the manufacturer.
Thanks a lot
haegarhorrib

Originally Posted by Jeffrey
The Satellite L50-B-81 isn’t known to me… I assume you mistyped the model number… Could you double check your model number and share the right name with us?
Thanks for the hint .
What I wanted to Type was
L50-B-281.
THX
haegarhorrib

My usb won't work in my laptop and my ipad is disabled, how can i connect it to itunes?

For some reason i decided to let my little brother watch the match on my iPad mini. He then decided to disable it and now i can't get onto it. I have so many important pictures, videos and infomation on there i cannot afford to lose any! Please help.

You need to find a computer with working USB ports and install iTunes on that computer to get the Apple device drivers. Then you can hopefully copy your pictures and videos. If the computer cannot recognize the device because it is disabled, then you will have to restore. You will lose anything on the iPad that was not purchased through iTunes such as your pictures and videos.
Your other option is to go to an Apple store and explain the situation and perhaps the store can extract your information.

Got the Stratosphere update, and USB won't work anymore

Hi all.
At a loss here. I did the update today for the OS...and other than fixing the annoying cb# issue, and the change to the unlock, what I'm stumped on is when I connect to my PC, via USB, I get "Sorry! Process com.android.settings stoped unexpectely. Try again" and a force close box.
If I got to the USB Settings in the Settings area, it also faults when I tap on the USB settings.
Anyone have any idea how to fix this?

I'm with you, jrh4054. As I posted here: https://community.verizonwireless.com/message/868896#868896, I find that even though I get the error, I can still access the phone from my computer via USB to manage files. I plan to just ignore it, assuming that the functionality remains the same. It seems that it does not even occur every time. No way it's worth a factory reset.
The "debug" option that has been mentioned is found here: https://community.verizonwireless.com/message/862342#862342. I'm honestly not sure what it is supposed to accomplish.
As mkracing66 pointed out, I discovered today that if I go to Settings > USB Settings, I get the same error when I tap on the USB settings. That seems to be where the problem is really located.
Many, many people seem to be encountering this error. Looks to me like a matter of an update that was almost ready to roll out, but not quite. Will there be a fix? I'd sure like to think so, but we'll see.

Left USB won't work with mouse or hard drive

I can only use my right-side USB port with my Mighty Mouse and external hard drive. When plugging either of these accessories into the left-side USB port, the computer does not recognize the items. What could the problem be?
Thanks for the help!

Hi, Charlie -
This Apple KBase article may have info you can use -
Article #58649 - Apple Pro Keyboard: Devices Connected
I came across that article shortly after my keyboard died, which was not long after I began having dead-mouse problems.
I made the assumption that my mouse was overloading the power-passthrough capabilities of the unpowered hub in the keyboard. I reconfigured my USB connection scheme so that the mouse was connected to the powered hub in my monitor and nothing was connected to the keyboard. That was several years ago, and no more problems.

RAID DRIVE WON'T WORK IN LINK MEDIA BROWSER

I have a RAID 5 drive connected to my MACPRO (MacPro5,1), OSX 10.9.2. Its working fine on OS. In Premiere Pro CC I can import files from it no problem, everything seems to be fine until I try to link media from it. The link media browser won't access it. I can see it, I can see the RAID drives icon, but it won't access the files.
In the link media browser it won't show on the Local Drives list on the left pane. When I double click on local drives, on the right pane I can see the RAID HD icon, but when I click on it it won't open it. It knows its there but can't access it. I don't get it. I can import files from it, etc, but not link files. I would have to redo the whole sequence with files from that RAID drive and its days of work.
I would appreciate enormously any help with this issue.

Adobe CC 2014 v8.1
iMac 27" 3.4GHz w/12GB Ram.
OS 10.9.5
OWC Mercutry ELite Pro Dual.
RAID 0
Thunderbolt.
No adapters or daisy chaining going on.
The RAID is new and only has about 700GB of data on it.
I read on Creative Cow that alexojedav522 was able to figure out that the size of the drive was his issue:
https://forums.creativecow.net/thread/3/954245
After reading that I tried repartitioning my RAID into two sections of 2tb each (let's call them Partition1 and Partition2).
So Partition1 is just the original partition (which was 4TB) shrunken down to 2TB.
Partition2 is the brand new partition.
Oddly enough, I can access Partition2 via Media Browser just fine.
And when I move media onto it I can relink it as well).
But Partition1 is still not accessible via Premiere at all.
I am currently moving everything off of Partition1 and onto Partition2, so that I can at least relink my project and get to work.
But obviously that isn't a permanent solution.

Satellite C50-A-157 Sandisk USB won't work in Recovery Media Centre

Similar Messages

Maybe you are looking for