Satellite C655-S5128 won't boot up

Satellite C655-S5128 shut down due to low battery before we could get charger plugged in.  Now it won't boot up.  It's stuck on the Toshiba logo page that also says to press F2 or F12 for setup/boot options.  There's also a faint beeping sound we've never heard before. After a while of pushing buttons an error message popped up stating no bootable device can be found.  Any suggestions are appreciated.

Satellite C655-S5128
Let's try a proper system reset, and see if this helps bring your laptop back.  Power off your system, unplug everything including the AC, remove the battery, press and hold down the power on button for 30 seconds, replace battery and AC, power on, when you see the Toshiba logo press the 'F2' key to enter BIOS Setup, in setup press 'F9' to load setup defaults, press 'F10' to save and exit, then try to boot into Windows again.
Let us know what happens. Good luck.
Mike

Similar Messages

  • C655-S5128 won't boot or read recovery dvd's

    I caught the FBI Money Pak malware.  Got rid of it, or not so it might seem, and ran scans and Windows 7 repairs and thought all was well.  3 days later woke up to the unit saying it had a software or new hardware issue and wanted to run Windows repair.  I let it and the computer went black.  Several hours later tried a re start and went to bios then tried to load and went black.
    The unit will not load in any of the safe modes, nor will it read recovery media made when i bought the unit.  None of the recommended recovery schemes in the manual work. 
    Suggestions other than remove the hard drive and start over?

    Satellite C655-S5128
    Let's try a proper system reset, and see if this helps bring your laptop back.  Power off your system, unplug everything including the AC, remove the battery, press and hold down the power on button for 30 seconds, replace battery and AC, power on, when you see the Toshiba logo press the 'F2' key to enter BIOS Setup, in setup press 'F9' to load setup defaults, press 'F10' to save and exit, then try to boot into Windows again.
    Let us know what happens. Good luck.
    Mike

  • Satellite C655-S5041 won't boot with new RAM (8GB)

    I recently bought some Ram from Newegg which can be found here. I installed the aforementioned Ram into my laptop following the correct method (unplug, remove battery, etc.) however when I booted my computer up I received a black screen with a blinking cursor that freezes after a few seconds shortly after the manufacturer's page is loaded.
    I know for a fact that the Ram I bought is compatible with my laptop as I'm using one of the 2 sticks at the moment along with the original Ram from my laptop. Here's where I am really having issues though.
    When I have just one stick of Ram I purchased installed without the original stick my computer fails to boot up also regardless of which slot the Rams in. I have tested the sticks I bought, and my computer will boot up with them, just not without the original stick that came with my computer which wouldn't be an issue except that a) there's only 2 slots, and b) my laptop can't have more than 8GB of Ram.
    My BIOS is up to date (Ver1.6) and so long as I have my original stick of Ram installed my computer boots without any issues. Needless to say you can see why I'm in need of some help.
    Any help would be greatly appreciated. If you need any other specifics regarding my computer or settings feel free to ask and I'll do what I can to find them out.

    Satellite C655-S5047 Specifications
    Satellite C655D-S5041 Specifications
    Is your model is a Satellite C655-S5047, or a Satellite C655D-S5041, as there is no C655-S5041. Toshiba laptops are extremely finicky about the RAM they will accept, regardless of the advertisied compatability of other modules. It is imperative to to be percise about your model number as:
    The only approved replacement RAM modules for a Satellite C655-S5047 are shown on the spec sheet:
    Memory Upgrade
    Part Number Description
    PA3669U-1M2G Toshiba 2GB DDR2-800 Memory Module
    PA3670U-1M4G Toshiba 4GB DDR2-800 Memory Module
    Or the best quality compatible Kingston Memory modules. However, if this is your system, unless you are very lucky, I doubt you will find the 4GB modules available from Toshiba, Kingston, or a third party supplier. I use the same memory in my system.
    The only approved replacement RAM modules for a Satellite C655D-S5041 are shown on the spec sheet:
    Memory Upgrade
    Part Number Description
    PA3676U-1M2G Toshiba 2GB DDR3-1066 Memory Module
    PA3677U-1M4G Toshiba 4GB DDR3-1066 Memory Module
    Or the best quality compatible Kingston Memory modules. These modules:
    Part Number: PA3677U-1M4G
    Part Number: KTT1066D3/4G
    You purchased DDR3-1066 modules, which might work in the Satellite C655D-S5041. However, I sincerely doubt they will work in the Satellite C655-S5047.
    Mike

  • Satellite A205-S5804 won't boot.

    My computer Satellite A205-S5804 won't boot.
    It won't run on safe mode, and it won't run the system restore.
    It remains black with a cursor, if anything at all.
    How do I get my computer back on?

    Hi
    Youve got a cursor which is flashing in the upper left corner?
    In such case you should check of the HDD has been recognized by BIOS!
    If the HDD is listed in BIOS then I would recommend checking the HDD using the drives fitness test:
    http://www.hitachigst.com/hdd/support/download.htm
    To run the drives fitness test you must download the appropriate creator or image and create a self-booting media.
    Check it!

  • Satellite L40 18P won't boot anymore

    Hello folks,
    my Satellite L40 18P won't boot anymore. All I get is the Power LED to go green. The DVD ROM drive blinks and I can open and close it - but that's it. Nothing else happens.
    Any idea in the forum what I can do to get the notebook boot again ? Or please ask questions for additional details.
    many thanks, Johi 13

    Hi,
    wow, that was fast.
    No, I can't see anything - the screen stays black. I do not hear the HDD start, neither do I hear the fan.
    This behavior appeard for the first time yesterday evening.
    Last activity was (if I remember correctly) closing the lid and sending the notebook to standby.
    So far, I haven't tested it with an external monitor.
    thanks, Johi13

  • Satellite C655-S5305 fails to boot

    My daughter's Satellite C655-S5305 laptop won't boot.  She reports to have shut down the computer this morning (without any updates or having downloaded anything) and says that the computer won't come back on.
    Upon pressing the power button, the Toshiba screen comes up, then changes to a blank screen with a flashing cursor in the top left corner.  The cursor just continues to blink and nothing else happens.
    After researching the forum, I've tried pressing F2, F12 and have settled in to reverting to factory settings.  After pressing "0", the screen develops about 1/4 inch of multicolored dots at the upper margin of the screen and nothing else happens.  After pressing F12, then selecting the HDD recovery option, the warning screen appears and after selecting yes and hitting enter, the same thing occurs.
    Short of sending the computer in for service (it's less than 2 months old), I'm out of options.  Any help would be greatly appreciated.  Thanks.

    My laptop is only 3months since I bought it went blank and it will not boot. Nothing on the screen, I tried external screen but it will not switch, Caps and Nums buttons work, but network doesn't seem to work, fans spin warm air so there is some activity.  I pulled battery off and restarted it at least 5 times now, pressed F2, F12, and tried Fn with various combinations, yet nothing happens!  What do I do???

  • Satellite Pro A10 won't boot up - Where to get the disks

    I have a Satellite Pro A10 which currently won't boot up Windows (XP) as it says
    The following file is corrupt or damaged:
    C:\Windows\System32\Config\System
    The Tools & Utilities CD-Rom which came with my laptop has unfortunately been scratched and won't boot.
    I have the two System Recovery Disks, which are fine.
    My questions:
    1. Is it possible to purchase a replacement Tools & Utilities CD-Rom?
    2. If so, where from?
    3. Is there a way of restoring my laptop without having to completely reinstall everything and lose all my files?
    Thanks
    Message was edited by: Stuart_2007

    Regarding the point;
    a) Usually it should be possible to order the Tools & Utilities CD-Rom but I ask why?
    b) You can purchase the CD from the ASP in your country
    c) The older recovery CD supports an expert mode. You can use this mode to choose the partition where the OS should be installed. In such case only this partition will be formatted.
    But listen dude. You dont need to order the Tools & Utilities CD because on this CD you will find only the Toshiba drivers which can be downloaded from the Toshiba page too.

  • Satellite L850-161 won't boot from recovery disk

    When I got the laptop in 2012 I created 4 recovery disks but since then i've had my HDD replaced in my SATELLITE L850-161 but it has the recovery partition with nothing in it and the laptop won't boot from disk either so I can't format it but really need to, any suggestions??

    If you have 4 recovery discs be sure you start installation with disc number 1. After HDD exchange you should be able to use created recovery discs for recovery image installation.
    Does some other bootable disc starts properly?
    To be honest I dont understand how new HDDD can contain recovery partition that will be created if recovery image installation works.
    Problem is that in such situation you dont have many options. In worst case you can order original recovery disc for your machine.

  • Satellite Pro A10 won't boot (HDD seems to be missing)

    Hello, I hope someone can give me some advice on this problem: I have a 2 year old Satellite Pro A10. Recently it won't boot at all and I notice that if i look at the directories in the C: drive using the command prompt it says 'file not found'. Can't start Windows at all, not even in Safe Mode.
    Using the recovery disks doesn't help either I get messages like No such fixed Disk and 'Extraction Failed'.
    does this mean I have:
    1 A damaged hard disk
    2. Faulty connections to the HDD? - if so how do I rectify this?
    the system didn't crash before this happened, it failed to load up when I started it.
    Would appreciate any help.
    Thanks,
    Scl

    Jeffery and Ivan25 are correct in HDD malfunction. Try and remove and reattach the HDD and see if BIOS sees the HDD. If not you are going to need to order a replacement HDD. If BIOS does not even see the HDD then you wont even be able to install any Operating system, because there is logically nowhere to store the data being copied.
    Take it to an Authorized service provider near you to have it checked out. Could also very well be the HDD Controller on the Motherboard has went bad and can not detect any HDD connected to the motherboard even if it is new and unused.

  • Satellite P775-S7375 Won't boot up

    Hello,
    I have a fairly new (about 4 months old) Satellite P775-S7375 that suddenly won't boot.  When I press the power button, the lights light up and I can hear a fan run for about 3 seconds, then it shuts down.
    I have tried pulling the battery, and power cable out, pressing the power button for 60 seconds, putting the power cable back in - same result.
    I tired the above,  but with putting in a fully charged battery instead of the power cable - same result.  This laptop is not even getting to the intal spalsh screen or BIOS screen.  It's literally turning itself off after about 3 seconds.
    Any idea on what I should try or is this a dead laptop needing to be sent back to Toshiba for service?
    Thanks!

    It was the motherboard.  I shipped it back to Toshiba and they fixed it.  Unfortunately for me, their quality control is awful and they forgot to reattach the DVD drive to the case.  A tiny screw is missing. So now when I eject a CD/DVD the whole drive slides out of the bay.
    After spending the better part of an hour on the phone with the support staff (which involved me being transferred to a number that was no longer working, then being transferred to a repair depot phone that said their hours were M-F 8am-8pm EST and oh, they're closed right now even though it is 11am on Monday???), I have to ship the laptop back across the country so someone can put in a $.01 screw and ship it back across the country.
    I've learned my lesson about Toshiba.

  • Satellite C870D-12F won't boot Win8

    Hi
    My Satellite won't boot (windows 8) anymore, and I'm also not able to reset to factory settings.
    The harddisk is still ok if I put it in another PC I can see all the partitions.
    Does anyone sees something wrong in the partition type or properties?
    Thanks in advance for any help.
    Kindest regards
    +Message was edited: part of the message has been removed+

    Hi All
    No help was afforded ,so I fixed it myself!! And WITHOUT the recovery medium.
    I installed windows 8.1 again from a downloaded iso (I didn't had a key for this version).
    Now I had an unregisterd windows running but "Recovery back to Factory setting" was still not available.
    But I was able to get the recovery partition to be recognized again with this procedure
    I downloaded Visual BCD: In here I check alt the path's in the BCD store and especially if the GUID of the "Windows Recovery Environment" is the same as the one used for "recoverysequence" in your "OS loader". You can also get here the WinReBCD id (GUID), you will need this in ReAgent.xml
    A GUID looks like this: {ecca5163-d630-9447-a175-fc367f40a9e5}
    Second thing: check in c:\windows\system32\recovery\Reagent.xml that
    WinReBCD, ImageLocation, PBRImageLocation, DownlevelWinreLocation and OSInstallationLocation are pointing to the right "path, GUID and Offset".
    +In my case ImageLocation, PBRImageLocation and DownlevelWinreLocation point to partition 1 (first on).+
    +OSInstallationLocation points to partition 6 (last one)+
    +example:+
    +<ImageLocation path="\Recovery\WindowsRE" id="0" *offset="1048576"* guid="{ecca5163-d630-9447-a175-fc367f40a9e5}"/>+

  • Satellite L20-260 won't boot up, everytime it freezes with no reasons

    Hi all,
    I've got a sad problem with my satellite, after 3-4 days I've installed a new OS (i've tried with XP SP2 and Kubuntu) system won't boot up, everytime it freezes with no reasons, the only way is to perferom a new OS installation. Could it be an hardware problem maybe related to RAM or HDD?
    10x, Daniele.

    Hi
    This is not easy to say if the problem is software or hardware related.
    You should install the OS from the Toshiba recovery CD and test the functionality again
    If the notebook will start freezes again immediately after recovery CD installation then it could be a hardware problem.
    You could try to use the MemTest 3.5 tool.
    It checks the memory for malfunction.

  • Satellite A40-231 won't boot after wrong firmware update

    Hi,
    i own a toshiba satellite a40-231.it won't boot anymore because i have flashed it's dvd-rw drive(sdr-6112) with the wrong firmware and i also made a big mistake making a non-bootable active dos partition,trying to flash the correct firmware.So, my question is: can i boot from usb flash disk?i believe it's the only option i have left, if not network boot.
    Thanks in advance!

    Hi
    As far as I know its not possible to boot from any other devices as from USB FDD / HDD / CD-ROM / LAN
    You could boot from network but if you want to install the OS via LAN you will need an RIS server. But its not very easy to do it without any additional experience. So I think this option is nothing for you.
    It seems the drive is dead or malfunctions and therefore the best idea is to replace the device drive. I know, its hard to hear that but I dont see any other solution

  • Satellite C655-S5044 won't recognize TSST CDDVDW TS-L633C ATA device after windows 7 update

    Laptop: Toshiba Satellite C655-S5044; Windows 7 64-bit
    DVD Drive - TSST CDDVDW TS-L633C ATA Device
    After an automatic Windows update, the CD/DVD drive is no longer recognized.
    Running troubleshoot on the PC yields:
    Problem detected with TSST CDDVDW TS-L633C ATA Device Driver has been disabled
    Checking for new drivers says I have the latest.
    I tried running a microsoft fixit for DVD/CD drives - no problem found
    I tried deinstalling the driver, then rebooting.  This yields a message:
    Device Driver was not successfully installed please consult with your device manufacturer.
    I tried the TSST website for Toshiba and that rerouted me here.
    Searching the forums I have seen similar issues with other hardware/OS combinations but not exactly the same.
    Additional Info from the device manager:
    Device Type:  DVD/CD-ROM Drive
    Manufacturer: (Standard CD-ROM drives)
    Location:  Location 0 (Channel 1, target 0, Lun 0)
    I suspect that I have multiple device drivers on the computer for this device and the OS is installing one that doesn't work.
    How can I get the correct current driver and install it?
    Does anyone recognize this problem and have a fix?
    Thanks.

    Satellite C655-S5044
    I didn't find that model anywhere.
    Device Driver was not successfully installed please consult with your device manufacturer.
    The driver is native to Windows. Sounds to me like a hardware malfunction.
    After an automatic Windows update,..
    In a Microsoft forum, they would tell you to do a System Restore to before the Windows Update. If that fixed the problem, then apply the updates one at a time to identify the culprit.
    -Jerry

  • My Satellite C50-B won't boot from HDD

    Machine Details:-
    Model Number: PSCMLA-03F07Q
    Serial Number: XE343127P
    Computer won't boot from harddrive. No error messages, just Toshiba splash screen at end of self test.
    A couple of times a reinstall of the operating system seemed to correct the problem but then it would go again, now the problem is consistent.
    I've narrowed down possibilities to a BIOS fault, reasons-
    System boots from USB without any problems. Installing of operating systems proceeds with no errors. Harddrive SMART data reports a perfectly healthy harddrive. Memcheck returns no errors.
    The obvious solution is to reload the BIOS, just resetting it achieves nothing. But here's the problem.
    The updated BIOS 1.4 that the Australian website offers is a Windows program and the computer can't boot Windows.
    Obvious answer is to use a bootable USB stick with a "live" operating system on it but all of these systems are Linux and the BIOS update is a Windows program. So much for intelligent solutions.
    Downloaded Bios version 1.7 from European site but the iso inside that rar file is empty, 25 Mb in size but nothing in it according to Linux. Tried running it's program on a Win7 64bit computer and it returns an error that it could not find the correct iso file.
    I've submitted a support request by email to Toshiba but they reckon it could take 3 days to get a reply so I thought I'd ask here as well. Can anyone please point me to a working copy of the latest BIOS update disk for a Satelite C50-B laptop? Please note - this model doesn't have a CD drive so the iso must be compatable with USB boot.
    Cheers,
    Andrew.

    OK, found the answer.
    Bios was corrupted but not critically so, turns out that this laptop should never have been able to boot linux in the first place. It's only because of the corrupted bios that I got away with it a few times. Ended up getting a valid copy from a blog in Russia.
    Toshiba used to be a byword for quality in the computer world but this is definately no longer the case due to poor (cheap) new quality control practices. Also it seems that Toshiba is no longer really concerned with making computers, they're more interested in selling Windows and GE Insurance Policies disguised as extended warrantees.
    From now on I will definately be making sure that my customers understand the troubles they can have when buying Toshiba Laptops.
    As for running Linux, I'm including this so that it will help other poor unfortunates who thought they were buying a computer instead of just a Windows platform.
    The problem started with Microsoft, their proprietry MBR boot system was no longer valid in a modern world and they had to adopt the open source GPT partitioning system with UEFI boot, but in typical Microsoft fashion they couldn't stick to the widely accepted standard conventions for how the EFI boot partition should be laid out. And Toshiba is Microsoft's new "friend with benefits" so instead of sending Microsoft back to the drawing board they've rewritten their bios so that it looks for the Microsoft Win8.1 EFI boot partition and ignores all others.
    The quick answer is to edit your boot partition after install and make it look like Microsoft's. Please note that you don't have to do this with other brands of computer, only Toshiba.
    Here's a link with full instructions including pictures, it's written for Ubuntu but is easily adapted to almost any other operating system.
    http://linuxontoshiba.blogspot.de/2014/05/getting-ubuntu-1404-to-boot-from.html?showComment=1410953307121
    Hope that helps a few people before it gets deleted.
    Cheers,
    Andrew.

Maybe you are looking for

  • JSSE Truststore

    i follow the step that was given by this web page to set up an SSL: "http://www.onjava.com/pub/a/onjava/2001/05/03/java_security.html" and i m facing problem with the truststore. i don't have the "lib/security/jssecacerts" and the only file was the c

  • Exchange 2010 OWA : TMG Error 12302 The server denied the specified Uniform Resource Locator (URL).

    Hello All, We are using TMG2010 (SP2, rollup4) for publishing Exchange 2010 OWA sites. The issue is that after every 10-24 hrs , the TMG server stops logging in OWA sites and start giving below error. Then we have to restart the server one two times

  • How to replace my HP Hynix RAM

    hello, we have dispatched  HP Hynix 4GB server ram for replacement  at Jasola Service center. we have clicked a image of RAM before dispatchment,  at that time serial no. and Sticker was O.K  and it was in good condition. but the service center repli

  • Advantages in Webdynpro Java Over WD ABAP

    Hi All Can you please let me know what are the advantages in webdynpro java over WD ABAP?? if anybody helps quickly then it would be great help to me Thanks Trisha Rani

  • Anyway to set ProPhotoRGB as output space in ACR hosted by Elements?

    Is there anyway to set ProPhoto RGB as the output space in ACR 4.4.1 hosted by Ps Elements 6 on a Windows Vista Home Premium laptop? The images will be properly corrected using the full version of Photoshop 10.0.1 on my Mac, but I'm used to seeing th