Satellite C660 - Blank screen - No output - External monitor OK

I recently bought a C660 from ebay as a non-working repair project, listed as having no output to the LED screen but working ok on an external monitor.
After stripping it down, I found that the 40 pin connector to the LED panel had 3 damaged pins on the left side, so assuming that was the issue, I got another cable and rebuilt it. However, still no output to the LED panel, but all working fine on an external monitor.
As I have a spare new panel in stock, the next move was to replace the LED panel - still no output, except to the external monitor.
I have checked the setting for the video output (Fn+F5) and it is no different on any setting.
I have seen a couple of threads on here where people are having issues with no video output after a BIOS update (however I do not know if this has been done or not in this case).
Does anyone have any ideas as to what else I could check for to see what the problem might be?
Any help greatly appreciated.

>I have seen a couple of threads on here where people are having issues with no video output after a BIOS update (however I do not know if this has been done or not in this case).
If BIOS update fails, the unit would not power up and this results in black screen but this has nothing to do with your issue. The external monitor works properly so BIOS is OK.
Your issue is related to faulty internal display or the connection between the display and motherboard.
Both should be checked!

Similar Messages

HT5437 How can I use apple TV to connect my computer to the tv screen as an external monitor?

How can I use apple TV to connect my computer to the tv screen as an external monitor?

Morning jotref,
Thanks for using Apple Support Communities.
For more information on this, take a look at this article:
About AirPlay Mirroring in OS X Mountain Lion
http://support.apple.com/kb/ht5404
Best of luck,
Mario

How to switch off internal macbook screen when using external monitor(s)

as far as i observed, adding external displays ( running different screens on them, not mirroring) to a macbook pro increases the gpu workload and with that comes temperature rise in the laptop and increase in ventilator noise - and probably increased hardware aging and risk of component faillure due to high temperature inside the laptop.
simply try connecting two external 27" screens and open some flash video on both of them. then run a temperature monitoring software and watch temps rise, compared to running same flash videos / demanding tasks only on one connected external screen or only on the laptop screen with no external monitor connected.
especially in mavericks, due to its increased background routines, such a set-up appears ever the more taxing, then again who does not love apple`s nice adds showing laptops with two 27” screens connected to it and the workspace vision they invoke....
i have seen temps around 100° to 102° celsius on a 13" macbook pro 2012 edition, which i would expect is territory where the cpu / gpu temp safety switches will trigger system shutdown any time soon ( hardware status before verified as fully in order by apple service and default osx installation)
imagine your anti-virus software starting some realtime content screening while runnign some demanding tasks already and the system shuts down easily (all such situation observed in reality)
(would be interesting to see how a retina display macbook fares with 2 external monitors running demanding tasks, considering the retina display already increased taxing for the gpu - any experience from users of such a setup would be very much appreciated as it will provide critical purchase decision intelligence for all of us envisioning a retina-book and two big screens adoring our desks...)
turning down the macbook`s built-in screen`s backlight may reduce power consumption but i have not seen any evidence that it switches off the gpu-to-screen feed and respective gpu load - it certainly did not prevent gpu, cpu, board, etc temps to rise to borderline levels.
so the key question here is, how to switch off the macbook pro`s built-in screen in order to avoid gpu cycles being wasted on that screen ( and the resulting heat developments) when working with big external screen(s) connected to the laptop ?

this thread talks about running several monitors as advertised by apple and running demanding task on them.
with the lid open, the keyboard offers a very efficiant heat escape vector, which is blocked when the lid is closed - this is a basic and commonsense insulation effect. this thread also mentions the use of temperature monitoring software and thus a repeatable test setup. the temps recorded were also mentioned. they rose when the lid was closed, the running task remaining unchanged. as far as i could track down the cpus in discussion will shut down around the 105 degree celsius range. i observed system shut downs when the system approached 103° celsius. not to mention that the fans will run loud well before that.
again this is on hardware checked and ok-ed by apple service.
the question still welcoming an expert answer: is there any way to switch off the built-in macbook monitor while the lid is open ?

MacBook Pro Blank Screen (Built - in & External) - continued

This thread is a continuation of [MacBook Pro Blank Screen (Built - in & External)|http://discussions.apple.com/thread.jspa?threadID=1478474]. The thread was getting too long and some browsers were timing out.
Thank you,
Apple Discussions Staff

I brought mine into the Apple Store last night. I had not left it for service last time as I had not cleared it of some confidential client data. This time, I encountered a much more knowledgeable Genius who seemed to have heard of the Nvidia problem.
So, my MBPro is on its way to the depot. It will apparently be $310 total, flat fee, supposedly ready within a week.
I do expect Apple will do the right thing eventually and extend warranties for the defective Nvidia subsystem. However, I can't wait until they do. I need my Macbook Pro to be functional.
Again, my strong advice...
*At the first hint you are getting this problem, turn on screen sharing.*
If you have this specific Nvidia problem, you will still be able to access the machine remotely, which can be incredibly valuable in terms of saving data before you send it for repair. When you hand it over, you will initial a statement saying you have backed up your data and Apple is not responsible if the machine is wiped during repairs. Set up screen sharing so you can operate the machine during the Nvidia failure.

How do I make the DVD player play full screen in my external monitor instead of my laptop?

I just upgraded to Lion, and I have my laptop screen and my external monitor, and every time I tell my computer to play a DVD in full screen, it makes the full screen slide over from my giant external montior to my tiny laptop screen. How do I make it not do this? I would like to be able to watch my DVDs on the larger high-res monitor instead of my tiny laptop screen, but I can't seem to find the right preferences window or something.

With DVD player open, have you check the menu bar > Window > Show/Hide Controller?

I am a brand new mac user...trying to figure out how to switch from the Mac Pro screen to my external monitor. Appreciate any help.

am a brand new mac user...trying to figure out how to switch from the Mac Pro screen to my external monitor. Appreciate any help. thanks

In Finder... goto Help... In the Search Window type in Displays...
Lots of Useful Information there...
You may find these Links Useful too:
http://www.apple.com/support/mac101/
http://www.apple.com/support/macbookpro/
Cheers,

Blank Screen in Output Display

Hi All,
I have a report output with REUSE_ALV_HIERSEQ_LIST_DISPLAY with custom PF Status and i have a custom button which call a CLass (Which perform some function at the background which the user doesn't notice) afterreturning from class
but now it displays a blank screen.
To overcome come this i called PERFORM OUTPUT again immediately after calling the class , now it diplays the out screen and user doesn't notice any difference but the problem is when i press the BACK button now it displays blank screen the back button.
When ever the control returns after calling the class it displays a blank screen
form output.
CALL FUNCTION 'REUSE_ALV_HIERSEQ_LIST_DISPLAY'
      EXPORTING
        i_callback_program       = v_repid
        i_callback_pf_status_set = 'SET_PF_STATUS'
        is_layout                = s_layout
        it_fieldcat              = t_fieldcatalog
        i_callback_user_command = 'USER_COMMAND'
        i_tabname_header         = 'Itab'
        i_tabname_item           = 'Itab1'
        it_events                = t_events
        is_keyinfo               = s_keyinfo
*        i_buffer_active          = 'A'
      TABLES
        t_outtab_header          = itab
        t_outtab_item            = itab1
      EXCEPTIONS
        program_error            = 1
        OTHERS                   = 2.
endoutput
Thanks in advance.

Hi
1.Check if v_repid is populating correctly or not
2. pass ITAB & ITAB1 in capital letters
        i_tabname_header         = 'ITAB'
       i_tabname_item           = 'ITAB1'
Hope this will solve the error.

How to blank laptop screen when using external monitor/

Hi there
I need some help with figuring out how to configure my xorg.conf for my Arch Linux 64 bit installation on a HP Pavilion dv 5000 laptop so that I can automatically blank my laptop screen when using an external monitor. I have Arch Linux installed along with Ubuntu Feisty. In Ubuntu my external monitor (Viewsonic 1912WB) was not detected at the time of installation but with the native 1280X800 resolution that is good for the laptop takes effect for the external monitor automatically when the external monitor is plugged in. The laptop monitor goes blank when the external monitor is plugged in.
In my Arch Linux installation I have not been able to configure a dual head configuration using the ATI Radeon drivers (fglrx). I have the native 1280X800 resolution set up for the laptop monitor and this resolution takes effect for the external monitor also. However the laptop monitor also continues to function when the external monitor is plugged in. I would like to blank the laptop monitor when using the external monitor.
I am attaching my Arch Linux xorg.conf and the Ubuntu xorg.conf below. Thanks for anyone who can help, I am having a lot of difficulty in figuring out how to set up xorg.conf among all the things that I have had to learn so far in Linux and I am a relative newcomer to the whole thing. I have tried to compare the two xorg.conf files and edit my Arch xorg.conf in accordance with the Ubuntu one but it did not work and I keep getting errors!
I am using XFCE as my Desktop environment.
Arch Linux xorg.conf
# File generated by xorgconfig.
# Copyright 2004 The X.Org Foundation
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
# Refer to the xorg.conf(5) man page for details about the format of
# this file.
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# Files section. This allows default font and rgb paths to be set
# Server flags section.
# Input devices
# Core keyboard's InputDevice section
# Core Pointer's InputDevice section
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the xorg.conf man page for a description of the options.
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
# Monitor section
# Any number of monitor sections may be present
# Graphics device section
# Any number of graphics device sections may be present
# Standard VGA Device:
# Device configured by xorgconfig:
# Screen sections
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
# ServerLayout sections.
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
# Section "DRI"
# Mode 0666
# EndSection
Section "ServerLayout"
# The Identifier line must be present
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
Identifier "Simple Layout"
Screen 0 "aticonfig-Screen[0]" 0 0
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
# RgbPath "/usr/share/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# FontPath "/usr/share/fonts/TTF"
# FontPath "/usr/share/fonts/Type1"
# FontPath "/usr/lib/X11/fonts/local/"
# FontPath "/usr/lib/X11/fonts/misc/"
# FontPath "/usr/lib/X11/fonts/75dpi/:unscaled"
# FontPath "/usr/lib/X11/fonts/100dpi/:unscaled"
# FontPath "/usr/lib/X11/fonts/Speedo/"
# FontPath "/usr/lib/X11/fonts/Type1/"
# FontPath "/usr/lib/X11/fonts/TrueType/"
# FontPath "/usr/lib/X11/fonts/freefont/"
# FontPath "/usr/lib/X11/fonts/75dpi/"
# FontPath "/usr/lib/X11/fonts/100dpi/"
# The module search path. The default path is shown here.
# ModulePath "/usr/lib/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
EndSection
Section "Module"
# This loads the DBE extension module.
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
# This loads the font modules
# Load "type1"
# This loads the GLX module
# Load "glx"
# This loads the DRI module
# Load "dri"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option    "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "freetype"
# Load "xtt"
EndSection
Section "InputDevice"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
# Option "Protocol" "Xqueue"
# Option "Xleds" "1 2 3"
# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# These are the default XKB settings for Xorg
# Option "XkbRules" "xorg"
# Option "XkbModel" "pc105"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""
# Option "XkbDisable"
Identifier "Keyboard1"
Driver "kbd"
Option    "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
Option    "XkbRules" "xorg"
Option    "XkbModel" "pc104"
Option    "XkbLayout" "us"
EndSection
Section "InputDevice"
# Identifier and driver
# the following line.
# Option "Protocol" "Xqueue"
# Mouse-speed setting for PS/2 mouse.
# Option "Resolution" "256"
# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.
# Option "BaudRate" "9600"
# Option "SampleRate" "150"
# Mouse wheel mapping. Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7. Change if your mouse has more than
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"
# ChordMiddle is an option for some 3-button Logitech mice
# Option "ChordMiddle"
Identifier "Mouse1"
Driver "mouse"
Option    "Protocol" "Auto" # Auto detect
Option    "Device" "/dev/input/mice"
# When using XQUEUE, comment out the above two lines, and uncomment
Option    "ZAxisMapping" "4 5 6 7"
# Emulate3Buttons is an option for 2-button mice
EndSection
Section "Monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
Identifier "My Monitor"
HorizSync 30.0 - 62.0
VertRefresh 50.0 - 70.0
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]"
Option    "VendorName" "ATI Proprietary Driver"
Option    "ModelName" "Generic Autodetecting Monitor"
Option    "DPMS" "true"
EndSection
Section "Device"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
Identifier "Standard VGA"
Driver "vga"
VendorName "Unknown"
BoardName "Unknown"
EndSection
Section "Device"
#VideoRam 131072
# Insert Clocks lines here if appropriate
Identifier "* Generic VESA compatible"
Driver "vesa"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]"
Driver "fglrx"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "* Generic VESA compatible"
Monitor "My Monitor"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1280x800" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1280x800" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x800" "800x600" "640x480"
EndSubSection
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]"
Device "aticonfig-Device[0]"
Monitor "aticonfig-Monitor[0]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Ubuntu xorg.conf
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
# Edit this file with caution, and see the xorg.conf(5) manual page.
# (Type "man xorg.conf" at the shell prompt.)
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Files"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
# path to defoma fonts
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Identifier "Synaptics Touchpad"
Driver "synaptics"
Option "SendCoreEvents" "true"
Option "Device" "/dev/psaux"
Option "Protocol" "auto-dev"
Option "HorizScrollDelta" "0"
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "Device"
Identifier "ATI Technologies Inc ATI Radeon XPRESS 200M 5955 (PCIE)"
Driver "ati"
BusID "PCI:1:5:0"
EndSection
Section "Monitor"
Identifier "Generic Monitor"
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "ATI Technologies Inc ATI Radeon XPRESS 200M 5955 (PCIE)"
Monitor "Generic Monitor"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1280x800"
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x800"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x800"
EndSubSection
SubSection "Display"
Depth 15
Modes "1280x800"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x800"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x800"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
InputDevice "Synaptics Touchpad"
EndSection
Section "DRI"
Mode 0666
EndSection

Xrandr 1.2 provides means for this. But today the only supported configuration is xorg-server-1.3 + xf86-video-intel-2.0. So for Radeon you'll have to wait for drivers that support Randr 1.2.
On my laptop (Thinkpad x60s) that would be:
xrandr --output VGA --auto
xrandr --output LVDS --off

Satellite A660-1FM - Max. screen resolution of external monitor

Hi All,
This may be (probably) an easy questions to answer but I have a Satellite A660-1FM and want to use it with my Samsung Syncmaster (forgotten model) external screen. I grabbed an HDMI->DVI-D adapter, and all is well, but here is my question:
The toshiba specs page for my laptop (http://uk.computers.toshiba-europe.com/innovation/product/Satellite-A660-1FM/1096013/toshibaShop/false/) shows an external resolution capability of:
Max Resolution : 2,048 x 1,536
Max Refresh Rate : 100 Hz
Non-interlaced resolution with max refresh rate : 1,920 x 1,200
But I get what I call standard HDMI resolution (not surprising I guess) when connected HDMI->DVI-D to my external monitor. I have previously run this monitor on my desktop at much high resolutions than 1080P, so the monitor is capable.
Just wondered what I'm missing here, or is it a case of the graphics card spec is higher than is possible to output from the laptop ?
Thanks for any help
Andy

Hi,
Thanks for the reply.
As to native resolution of the external monitor - unsure how to find this - but it was running a with a lot higher res when it was connected to my old desktop (which has died and been replaced by this laptop)
R/E the adapter - My Samsung Syncmaster monitor has a DVI-D cable sticking out the back of it, so I needed to connect that to my laptop - either vga-> DVI-D or HDMI-DVI-D to make use of it.
The external monitor is currently running at 1680 x 1050 using the laptop HDMI output -> HDMI-DVI-D adapater -> external monitor.
Before my desktop died, using the same external monitor I was running at 1680 x (guessing a bit here) 2048 ish (really sure I had a greater y res, this 1050 lark is really squishy).. in any case, the Y resolution was much much much better than 1050.
But, according to the specification for this laptop, it can output 2048 x 1536 to an external device (How, the HDMI and VGA outptu cannot go that high right ?)
So, I'm trying to figure out how to get the resolution on the laptop spec onto my external monitior, which has more than handled this resolution before my old gaming desktop died.
Thanks again for the reply - I hope this makes my question clearer.
Cheers
Andy

Only black screen on the external monitor with intel-virtual-output

Hello,
I tried to install bumblebee on my Lenovo W520 with this tutorial:
http://www.unixreich.com/blog/2013/linu … ly-solved/
I can activate my external monitor with "intel-virtual-output" and the monitor is switching on. But I can only see a black screen.
In the settings of gnome I can see my external monitor and configure it - but it shows nothing.
Have you any ideas?
Thanks a lot!

Hi,
Same problem here on my Lenovo W530.
Intel-virtual-output used to work fine but since it got upgraded the virtual output stays black.
I tried downgrading the xf86-video-intel package but there is a dependency conflict.
Available packages:
1) xf86-video-intel-2.99.916-3-x86_64.pkg.tar.xz (local)
2) xf86-video-intel-2.99.916-3-x86_64.pkg.tar.xz (remote)
3) xf86-video-intel-2.99.916-2-x86_64.pkg.tar.xz (local)
4) xf86-video-intel-2.99.916-2-x86_64.pkg.tar.xz (remote)
5) xf86-video-intel-2.99.916-1-x86_64.pkg.tar.xz (remote)
6) xf86-video-intel-2.99.914-4-x86_64.pkg.tar.xz (local)
7) xf86-video-intel-2.99.914-4-x86_64.pkg.tar.xz (remote)
8) xf86-video-intel-2.99.914-3-x86_64.pkg.tar.xz (remote)
9) xf86-video-intel-2.99.914-2-x86_64.pkg.tar.xz (remote)
10) xf86-video-intel-2.99.914-1-x86_64.pkg.tar.xz (remote)
11) xf86-video-intel-2.99.912-2-x86_64.pkg.tar.xz (local)
12) xf86-video-intel-2.99.912-2-x86_64.pkg.tar.xz (remote)
13) xf86-video-intel-2.99.912-1-x86_64.pkg.tar.xz (local)
14) xf86-video-intel-2.99.912-1-x86_64.pkg.tar.xz (remote)
15) xf86-video-intel-2.99.911-2-x86_64.pkg.tar.xz (local)
16) xf86-video-intel-2.99.911-2-x86_64.pkg.tar.xz (remote)
17) xf86-video-intel-2.99.911-1-x86_64.pkg.tar.xz (local)
18) xf86-video-intel-2.99.911-1-x86_64.pkg.tar.xz (remote)
19) xf86-video-intel-2.99.910-1-x86_64.pkg.tar.xz (local)
20) xf86-video-intel-2.99.910-1-x86_64.pkg.tar.xz (remote)
21) xf86-video-intel-2.99.909-2-x86_64.pkg.tar.xz (local)
22) xf86-video-intel-2.99.909-2-x86_64.pkg.tar.xz (remote)
23) xf86-video-intel-2.99.909-1-x86_64.pkg.tar.xz (remote)
24) xf86-video-intel-2.99.908-1-x86_64.pkg.tar.xz (remote)
25) xf86-video-intel-2.99.907-2-x86_64.pkg.tar.xz (local)
26) xf86-video-intel-2.99.907-2-x86_64.pkg.tar.xz (remote)
27) xf86-video-intel-2.99.907-1-x86_64.pkg.tar.xz (local)
28) xf86-video-intel-2.99.907-1-x86_64.pkg.tar.xz (remote)
29) xf86-video-intel-2.21.15-1-x86_64.pkg.tar.xz (local)
30) xf86-video-intel-2.21.15-1-x86_64.pkg.tar.xz (remote)
31) xf86-video-intel-2.21.14-2-x86_64.pkg.tar.xz (remote)
select a package by number: 16
loading packages...
warning: downgrading package xf86-video-intel (2.99.916-3 => 2.99.911-2)
resolving dependencies...
warning: cannot resolve "glamor-egl", a dependency of "xf86-video-intel"
:: The following package cannot be upgraded due to unresolvable dependencies:
xf86-video-intel
:: Do you want to skip the above package for this upgrade? [y/N]
error: failed to prepare transaction (could not satisfy dependencies)
:: xf86-video-intel: requires glamor-egl
Any Ideas what glamor-egl is?
Thanks!

Satellite P300 - blank screen since turned on, but sometimes working fine

Helo,
I have a Toshiba Satellite P300-1F0.
The display is blank when I turn it on, even on the boot up screen, and I cant hear the startup windows sounds.
Although if I turn it on and off, it will work after some tries, sometimes it works on the first try, some others I have to turn it on and off like 20 times before he finaly starts working. When it turns on it works perfectly.
I tried:
pressing the power button for 1 min while charger and battery out,
Checking manually the ram.
reinstalling and updating monitor and graphics card drivers.
shaking the lid to check if there is a cable broken
but none of these actions worked
I also noticed that the computer works with a external monitor (TV) connected via hdmi.
If i turn the laptop on, the screen is blank, and no windows sounds played, and after some minutes I plug in the hdmi cable, the Tv shows that windows was on, and sounds start to work from there.
While connected to the TV, I try to turn the display on by pressing (windws key+P) but it doesnt work.
In Screen resolution menu, windows cant detect the display, only the TV
Can anyone help me? what can be thr source of the problem?
Any soluction?
Thank you for your Time,
Adriano

As I can see you have started two identical threads. The second one is non http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=287272
Please continue discussion on first thread.

Satellite P100: Can I connect two external monitor to VGA & DVI port at the same time?

The Satellite P100 comes with two external monitor port. A VGA and a DVI. Can you have have two external monitor working at the same time? Can you have two external monitor as well as your internal display working at the same time (for a total of 3 display at the same time?
Here is what I have confirm:
Internal display + DVI connector display
OR
Internal display + VGA connector display
Is it possible to have:
DVI connector display + VGA connector display?
OR
DVI connector display + VGA connector display + Internal display?

As far as I know this is not possible and you can use either DVI or VGA port.
For signal output can be used only one port for external display.

Major Problem - LCD Screen Unreadable - Using External Monitor - First Aid

My LCD Screen is cracked, and only 5% of the screen is readable, and I dont have the resources to have it repaired, so have been using an external monitor to do my computing needs.
However, somehting happened to the OS X, and it MUST be repaired according to Disk First Aid. Putting the CD, and I want to force the output of the CD to be put on the external monitor, not the LCD since I can't read it. How can I make it show on the external monitor?

Hi Chef
Insert your System CD an select it as startup volume in "SystemPreferences"/"StartupDisk". Restart your book and close the lid right after the chime. Voilà, your external screen should be main screen now.
Regards P

Satellite L450D - blank screen at start-up

Hi
my laptop shows a blank screen totally black on start up the hard drive light is not flashing but I can hear the fan.
Suggestions welcomed

Sounds like a serious hardware problem.
You can check if the issue is related to the display or graphic chip.
Connect external monitor and check if something would be visible on the 2nd monitor.
In case nothing would be visible on the external monitor, your graphic chip (maybe motherboard) is affected

Satellite M50 - Blank screen after login on Win 8.1

Satellite M50 running Win 8.1
After login, get blank screen mouse but nothing else.
Can run Explorer.exe manually via Task manager to get going but some apps such as Acrobat and Windows Mail don't work.
I've searched online and tried all sorts of the suggested fixes to no avail.
Any suggestions gratefully received!

I don't know what is wrong there but you can try to shut down Win8 completely and check repair options. Try with system restore and roll back OS few days back. Maybe this will help.
http://aps2.toshiba-tro.de/kb0/TSB2A03ES0000R01.htm

Satellite C660 - Blank screen - No output - External monitor OK

Similar Messages

Maybe you are looking for