Satellite C660D-1GD: no sound and Red Cross over speaker

Just turned on my Laptop, Satellite C660D - 1GD and my sound isn't working.
There is a red cross over the speaker and the diagnosis didn't help at all.
Tried a system restore, nothing - no change at all. Tried going through the system drivers and there is no driver for sound :o. Ok, came to this site, downloaded the correct driver, installed and restarted and nothing again :s .
Updated the BIOS and then went into and checked the BIOS, and even checked for simple sound to just have my time wasted. Any help would be great.
Thanks in advance.

_Firstly:_
Did you check if mute isnt enabled?
Press FN + ESC to enable or disable mute
_Secondly:_
Go to control panel -> sound -> Playback tab
Check if the devices in the playback tab are activated and set as default device
Additionally click right to ensure that options are marked like; show hidden devices, show disabled devices
_Thirdly:_
The sound card is from Realtek.
So you can download the Realtek HD audio driver from Realtek driver page
Before installing new driver, uninstall installed Realtek driver from control panel -> programs & features

Similar Messages

Red Cross over my files

I keep getting this Red Cross over my files in CC. It's still there when I export it.
went through all layers, it ain't there by me. Anybody now what it is and how I can take it away?

I will repeat what Dave said and what has been said hundreds of times on this and other forums. If there's a Red Cross or other watermark on your project then you have a plug-in that is not been paid for or registered That's all it is to it.

How can i get my items to stay in place and not cross over each other when readjusting the browser s

How can i get my items to stay in place and not cross over each other when readjusting the browser size.
Basically on my site when i go from a small screen to a big screen everything doesn't adjust to the screen size. I don't know what im missing
Here's the link to the page all the pages & they all do it
http://theatricalworkslive.com/
Thanks in advance

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

No sound and red light

I have no sound and when I turn the volume up there's "a circle with a line through it" there is a red light coming out of the earphone socket. I tried unplugging it and it worked but I want to use my headphones sometimes and when I take them back out it goes back to the red light. I tried changing the settings to internal speakers but when I went to "Choose a device for sound output" there was only "Digital Out". How do I select internal speakers when they're not there, how do I fix this problem?

So my internal speakers stopped working around 9-12 months ago, along with it the all-too-familiar red light in the headphone jack. Tried all the toothpick (actually recommended by an Apple tech), headphone in-and-out, paper-clippy, throw salt over-your-shoulder ideas posted out there; all to no avail. Nothing would get that switch inside to pop back from it's position, and let my computer know that there was nothing plugged into the jack. After all that and NEAR A YEAR of no internal speakers, they inexplicably started working again the other day. I think what happened was that I had neglected to notice that my headphones were plugged in still when I tried to put my laptop in the case, and slightly tweaked the headphone jack port when the headphone jack hit the side of the case. Whatever you do, don't let anyone convince you that it's a logic board or I/O board failure. It seems very likely an obnoxious flaw in the jack's design, and I'm not surprised many people can get it working again by poking around and getting the switch inside the jack to return to its position.
This computer has been a workhorse for me and OSX is a great design, but If I were to issue one complaint about Apple it would be to stand behind thier hardware better (I've had other problems before too). I feel like they could have issued a proper procedure to fix this problem so that everyone with issues like this doesn't have pull thier hair out searching forums for solutions and getting unnecessary expensive repairs.

My laptop wifi connection disables automatically and red cross comes up

Hello
I just bought a new toshiba laptop L850-B211 with win 7 home premium 64 bit and i have noticed that my wifi disables automatically in between and i see a red cross come up on the tower icon....when i click on the tower cross it automatically connects....and
works fine again. But why is it disabling the wifi adapter automatically. this happens in every 30 or 40 mins even when i am surfing the net. Is this a hardware problem or some setting in windows 7 or toshiba power management utility which is causing this
problem. Also to mention i always use my laptop with power cord connected. The model no of wifi adapter is ATHEROS AR9485WB-EG.
Thanks,
Amit T.

Hi,
When trying to connect the Wireless network, please check the “Start the connection automatically” option. Then, when you trying to connect certain Wireless network next time, it should connect
to the Wireless network automatically.
In addition, update the wireless adapter driver to see how it works.
Also, please check this thread:
wireless adaptor disables automatically
Hope this helps.
Vincent Wang
TechNet Community Support

Turn off startup sound and red led.

Hey,
i need to turn off my vado startup sound, how to i do that?
Also, i dont want my red led to light up when i am filming. Help needed with that on also.
Thanks.

Turn "Instant Record" on in the setting by pressing the Play/Pause and Delete buttons at the same time. When it comes out of sleep mode it doesn't make a sound.
Being able to turn off the display while recording would also be useful or at least be able to dim it. I've disturbed some people while recording a play in a dark theatre. And I know it bothers me when someone is playing with there cell phone or other device in a low light situation.

Satellite P30-110 video, sound and mouse is jerky

Hi everyone,
I am running Win XP Pro. I had been having problems with my laptop for sometime now that whenever the hard drive was nearing full the entire system would start acting up in that when the system started up the Windows login sound would sounds like a CD skipping, then my mouse would jump around the screen and basically not move in a flowing manner, if I then try to watch video its like watching a DVD that skips and jumps every few seconds.
So to try and rectify this I did a much needed clean install of Windows. This seemed to fix the problem until after I installed the ATI display driver, I think, it may have been the previous drivers for the Toshiba Console/Control. So if the problem is the display adapter, what other options do I have? Or is it something else altogether?
Any help will be much appreciated!

>So if the problem is the display adapter, what other options do I have?
If this issue is related to the graphic chip then you have no many options; in such case the chip malfunction and should be replaced. But the point is that the graphic chip is not possible but only the whole motherboard replacement!
The mobo is not cheap and it would be a costly affair to replace such part. In my opinion its not worth to replace the mobo
But the point is that we dont know whats wrong exactly. Maybe its not a graphic card problem.
Did you try to reinstall the OS using the Recovery disk?
You should try this because the recovery disk already contains the necessary drivers and tools.
The issue could be related to a HDD issue. if the HDD start to malfunctions (it would rotate slower or some sectors would be damage) then the access to the data would be affected and the notebook could start to interrupt.
As you see, this are only some suggestions and I think nobody would be able to say, whats wrong until the notebooks hardware has been checked!

Black and white (and red :) all over?

is there a reason that when i configure a white MacBook to be exactly the same as a black MacBook there's still a $50 difference?
did i miss something?

the surface on the black macbook is black matte. the surface on the white on is the glossy plastic. the black matte is costlier to make(because diffrent type of plastics, doesnt scratch as easly...). that $50 diffrence is just from the bodys.

Battery, Red Cross, Dead Blackberry...

Hi All,
I put my BB 9220 in water by mistakenly and it started to work initially for say around 8 hours but now it shows a battery mark with a red cross over it. Can you please help in setting it right?

That battery is either discharged or damaged. It could also be a problem in the charging circuit. No telling with water damage.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

AE - Render differs from preview (get red outline and red layer)

Please excuse a newbie... I'm using AE and all looks good with the text I create.. I add a pre-set animation and then render to swf file. Sometimes all goes well, but most of the time I get a red hue over the graphics or the text gets an outline. See examples here...
This swf file rendered perfect.. all silver text and good reflection:
http://www.denmasterstudios.com/vision.html
This swf file (from the same AE document, I only changed the text) rendered with a red outline and red hue over the reflection:
http://www.denmasterstudios.com/hardware.html
It is kind of hard to explain, hence the examples. Thanks for taking the time to check it out. I'm spending too much time trying to diagnose.

Hello all and thanks for the tips. I really appreciate your help. After having it work sometimes and sometimes not, I definitely checked most everything you all mentioned. I really thought the answer shouuld have been in the areas you all pointed to... but I got lucky and found it somewhere else... maybe this was a newbie thing, but I'm willing to swallow my pride and cough it up...
My file was created from following Creative Cow's "reflection" tutorial step by step... in the tutorial, you "pre-compose" your text layer and create another layer below it. This other layer becomes your reflection.
Here's what was happening:
When I export to .swf, if I am viewing the pre-composed layers in the "comp" viewing area, I will get the red hue around stuff during the render, but not in the preview. If I switch from the pre-composed layers, back to the main layers, and view the main "comp" at the highest level and then render, I get a perfect render... make sense? perhaps it was human error... I just felt that the render would always look like what you are previewing. Make sure you render from the main layers and not while still looking at a pre-composed layer...
thanks again all!

Emac / PC cross over cable

Hello learned colleagues,
is it possible to connect an E-mac to a PC using their ethernet ports and a cross-over cable, (no switch)
I need to share files between both computers.
assistance appreciated
DB
eMac Mac OS X (10.3.3)

Yes, you can connect those two machines directly to each other with a crossover Ethernet cable. See these instructions for methods to share files.
(11185)

When plugged into computer a song started skipping, pressed pause but ipod sounds makes a clicking sound. Eventually goes to black screen with red cross. Cannot reset it and doesn't register on my computer.

I had my iPod plugged into my computer and was playing the songs from there. One song started skipping so I pressed the pause button, the ipod kept making a clicking sound like it was still struggling to play the song, eventually went to a black screen with a red cross with apple.com/support/ipod underneath. Have tried to reset it but does not work, comes up with apple logo and immediately makes the clicking sound and then crashes.
Is there anyway I can get my music and photos off?? I just got a new computer and had lost everything on my old one so only have the songs and photos on my ipod, desperately want to get them on to my computer.

You may have damaged the HDD which is located in that spot. I would take it in for service.

I tried down loading mozilla firefox to use as a web browser. It was downloaded 100% then when prompted to "run" the error message comes up with a red cross and the message'This file is corrupted" and won't let me proceed. What do I do now?

I tried down loading mozilla firefox to use as a web browser. It was downloaded 100% then when prompted to "run" An error message comes up with a red cross and the message'This file is corrupted" and won't let me proceed. What do I do now?

It is possible that your anti-virus software is corrupting the downloaded files or otherwise interfering with downloading files by Firefox.<br />
You can try to disable the real-time (live) scanning of files in your anti-virus software temporarily to see if that makes downloading work.
See http://kb.mozillazine.org/Unable_to_save_or_download_files

No sound and audio on Satellite A10-S177

My laptop is a Satellite A10-S177 XP, I happened to delete some programmes from my laptop in order to create space but it so happened that it affected my audio and sound and currently they the sound and audio bit in the control panel say no sound/audio driver. Tried to down load some software from the net but it did not work for it required printer access which I dont have.
I also dont have my XP installation CD, so am all lost and could do with any help from computer geniuses out there.
Thank you
Caroline

Hi there,
First of all would you tell me where did you downloaded some software where you thought it would bring back your sound?
Since your machine is from america you would have to go to the american driver download site:
http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_home.jsp
Please visit the link Ive posted and download the sound driver. Install it and check if the sound works.
In case of any question just feel free and ask...
Greetings

Function will not run (and shows with red cross in SQL Developer)

I have created the function below by typing into the "Enter SQL Statement" box in the SQL Developer tool and running. I see the message "create or REPLACE FUNCTION Statement Processed". I see the Function in the tree view, but it has a red cross icon next to it, so I guess somethings wrong with it. When I try to run it I get the message "The selected program is in an invalid state for running. Recompile the program and try again." If I right-click the function and compile then I get no errors but the red cross remains and I still can't run it.
What am I doing wrong?
Also, I am planning on supplying a SQL script to customers that will have this function at the top of the script, and then I will use the function throughout the rest of the script to decide whether or not to drop a table before re-creating it. Will that be ok? i.e. will the function be available to the rest of the script, or would the function creation need to be followed by a commit/grant/other?
CREATE OR REPLACE FUNCTION CHECK_TABLE_EXISTS(tableName VARCHAR2)
RETURN BOOLEAN IS
    tableExists NUMBER(1,0);
BEGIN
      SELECT COUNT(*) INTO tableExists FROM user_tables WHERE table_name=tableName;
      IF tableExists = 1 THEN
        RETURN TRUE;
      ELSE
        RETURN FALSE;
      END IF;
END CHECK_TABLE_EXISTS;Thanks,
Paul

Hello Try the same at sqlplus and see how it goes. It should not throw any error messages as I tried the same as a normal user Scott with only (connect, resource) priveleges. You dont have to grant any specific previleges for user_tables.
-Sri
SRI>conn scott/tiger@sri
Connected.
SRI>CREATE OR REPLACE FUNCTION CHECK_TABLE_EXISTS(tableName VARCHAR2)
2 RETURN BOOLEAN IS
3      tableExists NUMBER(1,0);
4 BEGIN
5        SELECT COUNT(*) INTO tableExists FROM user_tables WHERE table_name=tableName;
6        IF tableExists = 1 THEN
7          RETURN TRUE;
8        ELSE
9          RETURN FALSE;
10        END IF;
11 END CHECK_TABLE_EXISTS;
12 /
Function created.
SRI>set serverout on
SRI>begin
2 if check_table_exists('EMP') = TRUE
3 THEN
4 dbms_output.put_line('Found');
5 else
6 dbms_output.put_line('Not Found');
7 end if;
8 end;
9 /
Found
PL/SQL procedure successfully completed.

Satellite C660D-1GD: no sound and Red Cross over speaker

Similar Messages

Maybe you are looking for