Satellite L10-144 - Can't boot from Hard Disk

Hello.
Sorry for my english because I'm french. I have a problem with boot on this computer. I have installed windows xp on my hard disk but the computer don't boot on this hard disk. If I want to boot on this hard disk I must push F12 and select hard disk and after windows load.
In the bios the hard disk is in first but this hard disk don't boot automaticly.
Can you help me please?
Thanks a lot.

Hi Demilego,
Thats really strange... Normally the computer should boot from HDD automatically.
In your case I would check the BIOS and load the default settings.
Does it work?

Similar Messages

Can't boot from hard disk or from windows 7 recovery dvd

I have a 970A-G46 motherboard.
I can't boot from hard disk or from a windows 7 recovery dvd.
If I move the hard drive to another PC, it boots fine.
If I put the DVD in another PC's dvd drive, it can be accessed.
This machine will boot from an Ubuntu dvd and I can then access the HD directories and the recovery dvd.
What do I need to do?
Help and thanks

"I can't boot from hard disk or from a windows 7 recovery dvd."
What is that DVD from? Is it from a previous computer of some kind? Same question for HDD and the OS on it.

IBook G3 can't boot from hard disk or cd

Hello,
Just recently my laptop suddenly just would not start-up anymore. Here are it's symptoms and what I have tried:
-When the computer starts up I get the folder with the flashing "?" mark sign.
-I tried reseting the PMU and the PRAM and NVRAM (via Open Firmware) no luck.
-I tried booting from the Mac OS X installer CD (for Disk Utility) and the DiskWarrior CD by either holding "c" or "option" (i don't think it is a CD problem because the CD appears as an selection (hard drive doesn't) when I hold "option"). Unfortunately, when it goes to the grey apple on white screen with the wheel the apple becomes a no sign after about 30 seconds.
-I have tried to use "fsck" but I can't startup into single-user mode using Command+S
-I cannot start-up in Safe Mode
-I started it up in target mode (holding "T") but my other computer does not mount it on to the desktop and Prosoft Data Rescue X doesn't recognize the volume.
-I tried replacing the RAM (256mb) with the stick that came with the computer (128mb).
These are all the things in my problem-solving knowledge that I have tried and still can't fix it. If anything I just want to get the files off of it if that's possible.
The computer is an iBook G3 Dual USB 800MHz
Running Mac OSX 10.3.?
No Airport Card
256 MB Ram (at the moment)
Thanks for any help...
iBook G3 Dual (problem computer), eMac G4 (good computer) Mac OS X (10.3)
iBook G3 Dual (problem computer), eMac G4 (good computer) Mac OS X (10.3)

Hi, and welcome to Apple Discussions.
You have tried some of the recommendations in this Apple Knowledge Base article:
http://docs.info.apple.com/article.html?artnum=50959
But I hope something there will help.

I can't boot from instalation disk need help

can anyone tell me why i can't boot from instalation disk
i burn a DVD with verified iso with MD5 with Nero Express

i use burn image , of course and
i have a Sempron +2400 with asus a7s8x mainboard
and i download all 5 file for DVD x86 and then i copy /b all this files.
when computer boot from cd the screen is bleu with Solaris ................ v.20 message and after 1 second message became
Aolaris ..................v.20 and computer remain in this position

Godane's Archlinux boot from hard disk but it can't login in with slim

I download Godane's archiso-live-2009-09-24.iso , i havent cdrom , so i boot it from hard disk .
I extract iso to drive C: (fat32) ,two folder is "boot" "archiso-live"
my menu.lst is :
title Boot archiso-live Desktop
root (hd0,0)
find --set-root /boot/initrd.img
kernel /boot/vmlinuz elevator=deadline ramdisk_size=60% aufs nonfree=no vga=791
initrd /boot/initrd.img
load=overlay.lzm
The iso can be boot from hd ,but there isnt slim . only is console...
what can i do with this problem??

I think your problem is that load=overlay.lzm is in the wrong place.
Here is what i should look like:
title Boot archiso-live Desktop
root (hd0,0)
kernel /archiso-stable/boot/vmlinuz elevator=deadline lang=en_US keyb=us load=overlay,mesa usbdelay=5 nonfree=no xdisplay=old xdriver=no from=/dev/sda3/archiso-stable changes=/dev/sda3/changes session=xfce cdname=archiso-live
initrd /archiso-stable/boot/initrd.img
I use 'from' boot option so i can boot from my hard drive more easier. The way its booted above is for 2009-12-08 version of my archiso-live. Just thought you should know.
I hope this helps. And sorry for it being so late.

Satellite L20-100 can be booted from external USB hard drive?

I recently bought Toshiba Satellite L20-100 and I wonder if:
1. is there any possibility to boot this machine from external usb hard drive?
2. it is possible to attach another internal hard drive?
Supposing that the both answers above are 'no', how can I solve the following problem: I need hdd space, I need to boot 3 separate Wxp Operating Systems onto the same machine (Toshiba Satellite L20-100).

Booting from external USB HD - "No" would be the official, mcrsoft sponsored, answer. However, it is possible. Not easy but it can be done. I've seen it done with my own eyes and there are guides how to do this. Just look for it with search engine. But if you have enough disk space you better do what was suggested here - create 3 partitions and use boot manager.

Satellite U400-15E - Can't boot from new USB HDD

Hello.
Recently a bought an external WD My Book with 3TeraByte to use with my Satellite U400-15E. I can use it inside Windows 7 Ultimate with no problem. But if I try to boot from it (by pressing F12 key), the BIOS doesn't even see the drive.
Is this because Toshiba doesn't use Unified Extensible Firmware Interface (UEFI)? UEFI BIOS can overcome the 2.19TB limitation in todays computers easily, like the following Western Digital document explains:
[http://www.wdc.com/wdproducts/library/Flyer/ENG/2579-771501.pdf]
This would allow me to use my new external drive to store a Ghost image of my Toshiba's internal HDD for instance. I mean 3TB and even greater capacities are a reality today. When will Toshiba update their BIOSes to support UEFI?
Equipment used:
Toshiba Satellite U400-15E (BIOS v5.00 26-10-2010)
Western Digital My Book Essential 3TeraByte - Firmware v1.014 (USB 3.0 interface)
MS Windows 7 Ultimate - 32bit version
Thank you

Hello
Well... with this same computer, I already tried booting (successfully) from the following pendrive capacities:
8GB
16GB
32GB
All without problem.
And besides, before having the 3TeraByte WD, I had a 1TeraByte Iomega USB HDD from which I could store Ghost images, because the BIOS would show the 1TB Iomega drive after pressing F12 and Symantec Ghost could also detect the drive without problems.
But with this new 3TeraByte WD... the BIOS doesn't even show the drive after pressing F12.
So when you say +{color:#0000ff}So USB HDDs are not supported{color}+ are you refering booting from USB HDD?
Hum... I'm not sure about that.
I never tried booting an OS from the Iomega.
But that was never my purpose either.
My purpose is for the BIOS (and hopefully Symantec Ghost) to detect the WD USB drive, like it happened before with the 1TeraByte Iomega.
I was using a 1TeraByte Iomega "Select Series" drive.
With the Iomega I could create Ghost images of my Toshiba without a problem.
+{color:#0000ff}But you’re absolutely right: 3TB and greater capacities are reality today but Satellite U400 is older notebook model and not newest one.{color}+
A Laptop computer that has Two 64bit CPU cores and 8GB RAM capacity is not that old!
I think it could be a BIOS limitation, since it's not using UEFI.
Any more ideas?
Thank you.
Message was edited by: Binary-Synapse
Message was edited by: Binary-Synapse

Satellite L40-139 can't boot from CD

I have a Toshiba Satellite L40 - 139 that comes with installed vista!
A month ago i installed XP and it was working ok!
Yesterday I needed to reinstal XP and i choose clean instal from cd and in a process of installing I pressed the button to open dvd drive and end it!
Stupid mistake! From that point if i try to boot Windows from a dvd drive and the process stops at: checking your hardware configuration! - and blank screen!
Nothing happens!
What can i do?
Evrything else seems to run ok!
It's not problem with dvd drive because it reads a recovery CD for vista!
Please help!!

Hi
To clear the MBR, boot from the XP cd and go into the Recovery console (Repair). In command prompt type the following:
fixmbr (new master boot record creation)
fixboot (incase you get message cannot find ntldr)
bootcfg /rebuild (incase the boot.ini is damaged)

Can not boot from Hard Drive and or CD

Hi
I have a SUN Blade 1000. I loaded Solaris 10 a few days ago
and had it running pretty good until I ran an update program.
Now I cannot boot the dam thing. IT just hangs at a * prompt somwhere in the boot process.
I would like to re load Saolaris 10 but do not have a clue how to
make the machine boot from the CDROM if I cannot get to the OK prompt and I cannot get to ANY prompt that will let me get ANYwhere for that mater.
Is there some key or combination of keys I could push or something to get this dam thing to boot from the CDROM so I can start over???
Thank you in advance.
I have almost no experiance with SUN Solaris on SPARC or any other platform.
I know Windows and x86 hardware very well and have built many machines.
Is there a way to get into the Bios at boot time like with an x86 system? The last question is not as important as the first one of how do I boot this pig from the CD.
Thanks
Jim

How did you begin the previous installation?
Have you spent any time reading these forums?
Use the forum search function, keywords ...
"get to the ok prompt"
(in quotation marks)

Satellite A200-19L can't boot from CD

Hi guys,
I'm glad i found this forum site, i'm pretty much hopeful to find a solution here.
well this problem isn't very complicated, actually my DVD drive (Model TS-L632) is not reading anymore, so then i decided to changed it with new one, however it's not the same model as the original drive.
It's likely generic DVD drive actually.
Now when i inserted my recovery disk or any bootable disk isn't booting from CD and when i press F12 for boot priority i can't find any DVD/CD drive, but running in the windows i can find the DVD drive and it can normally read any CD.
Just having problem during booting in CD.
I was thinking maybe their is any security for this model that locked some hardware.
So guys please kindly help me how to figure it out,
any help would greatly appreciated.
Thanks,

>when i press F12 for boot priority i can't find any DVD/CD drive, but running in the windows i can find the DVD drive and it can normally read any CD.
The whole story sounds really strange to me
If you access the BIOS, can you see the CD/DVD drive details? Is the drive recognized properly?
If not then I assume the inserted ODD is not fully compatible due to different master/slave/c-sel settings.
>but running in the windows i can find the DVD drive and it can normally read any CD
Its also strange for me that the CD/DVD drive appears in device manager even though the CD/DVD drive option in booting menu does not appear.
But check firstly the BIOS

Can't boot from Install Disk for Leopard

I purchased the new xeon core dual which only boots in Leopard. I need to put Leopard on an external drive, so I purchased Leopard and tried to install it on an external drive. My computer starts to read the disk but before it even gets to the blue screen, it stops, scrolls down in a dark gray screen and says I need to restart by holding the power button down. The screen kind of looks like a kernal panic with oriental writing under the english.
I have tried by restarting and holding down the "c" key with no luck. I tried again with holding down the "option" key and when the hard drive and disk show up as choices. I chose the disk and still no luck. I disconnected all my external drives and tried again with no luck. I called tech support and they said it may be my optical drive. They set up an appointment with the genius bar at my local apple store. The genius listened to my drive and said there was nothing wrong with the drive and that it probably was a bad disk so they gave me a new one. Went home and tried with the new disk and same problem. Can anyone help?!! Thanks.

I purchased the new xeon core dual which only boots in Leopard.
I need to put Leopard on an external drive, so I purchased Leopard and tried to install it on an external drive.
There's your problem. Macs which ship with Leopard can't boot Leopard retail, unless it is newer than the Mac in question. Check the version of Leopard on the Leopard retail DVD you purchased in the second quote. If it is older than what was installed on your Mac Pro based on the Mac Pro install and restore DVD, then it won't work on your Mac Pro. If you want Leopard of the Mac Pro to be backed up to be an emergency boot volume for the Mac Pro on the external drive, use a cloning software*:
http://www.macmaps.com/backup.html
Or follow these directions to backup your Mac Pro DVD*:
http://www.macmaps.com/bootcd.html
If you need an emergency Leopard volume for another Mac, install it directly from that other Mac. If that other Mac lacks a DVD drive, get a Firewire DVD drive to do it.
- * Links to my pages may give me compensation.

Macbook Pro doesn't boot from hard disk

I recently applied an open firmware password to our Macbook Pro.
A co-worker tried to boot via the t-funtion which obviously doesn't work when the open firmware password is active. He forget to contact me so he tried to get it to work using some startup shortcuts. The folowing he had done:
* starting up while holding shift;
* starting up while holding command + option + P + R;
* having the accu out for a while
* starting up while holding shift and let the Mac on for a night
It seems that starting up from the Macintosh HD seems somehow blocked. THe system hangs on the Apple grey splashscreen with the loading icon turning.
I tried the following:
* Tried resetting PRAM using Option + Command + P + R (didn't hear any chimes);
* Trying to reset Open Firmware Password using Option + Command + O + F (nothing happens)
The most promising solution came when holding down the Option key: I got the lock and entered my Open Firmware Password. I was able to boot from the install disc. In the disc utility I verified the hard disk and repaired some permissions. I didn't get error messages. THen I used the startup utility and selected the hard drive as startup disk.
But when I restart the computer, it still hangs on the splash screen. So for now i've run out of ideas.
Message was edited by: StefSOFT
Message was edited by: StefSOFT

With intel Mac they changed to EFI firmware so a lot has changed. From reading this I think if you can get to install disk utilities then why not uncheck +Require password to change Open Firmware settings+ on Firmware Password Utility and that should free up the troubleshooting steps you list above that are blocked. Reinstall of OSX seems logical to attempt. Sadly without further testing could be hardware issue too, need to contact apple authorized service provider in this eventuality. One thing to bear in mind was whether your co-worker altered the firmware in any way, this might invalidate Apple One-Year Limited Warranty, AppleCare Protection Plan, or other AppleCare agreement.

Intel Xserve will NOT boot from hard disk drive

I have two Intel Xserves 2.0 QC machines
I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
When booting from The installation DVD media
The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
It does show, the still inserted Installation DVD.
I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
I have tried different caddy postions (left, middle and right)
I have tried bona fide Apple supplied Disk drives
I have tried various different caddies
I have tried installing Operating System 10.5.* and 10.6.8 server
I have run SMC reset and system reset
But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
Has anyone seen this behaviour?
Is it fixable?
Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
I have now run out of ideas and cannot find any help in discussions or just googling.
ANY help would be very appreciated
Regards
Tony

Antonio Hi !
QC = Quad core or QX as it is written on the "pull out" serial number tab at rear of system
I have 3 late 2006 Intel xserves
On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
I have many different Caddies and these have different product/model number labels
603-9965
603-9545
603-9796
these are marked "intel SATA"
The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb - all of which have been used in systems at one time or another
and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
Thanks for the guide - I will look through that and continue to try and find an answer

Satellite L850-161 won't boot from recovery disk

When I got the laptop in 2012 I created 4 recovery disks but since then i've had my HDD replaced in my SATELLITE L850-161 but it has the recovery partition with nothing in it and the laptop won't boot from disk either so I can't format it but really need to, any suggestions??

If you have 4 recovery discs be sure you start installation with disc number 1. After HDD exchange you should be able to use created recovery discs for recovery image installation.
Does some other bootable disc starts properly?
To be honest I dont understand how new HDDD can contain recovery partition that will be created if recovery image installation works.
Problem is that in such situation you dont have many options. In worst case you can order original recovery disc for your machine.

Can't boot from install disk, and says no airport card installed, HELP!

I bought a new Macbook Pro a few months ago, which recently had to go in for repair to have the screen changed. It came back with the new screen fitted but they had done a terrible job at aligning the lid, so it went back again. Came back and all looked good, until i booted up and realized that where my wifi icon is at the top of the screen, it wasn't connected. When clicking it to bring down the drop down menu of available wifi spots, all it said was "No Airport Card Installed"....Thinking a repair of disk permissions might be worth trying, I tried to boot from my OSX install disk holding down C, however when holding down C all it does is go on a constant loop of restarting, not even reaching the Apple logo. If I don't hold down C then it simply boots to the desktop, so i'm unable to access disk utility correctly to run a repair.
Being pretty fedup with the whole situation, the laptop has now gone back for a 3rd time, as it never had these two issues before. I was just wondering if anyone had any idea what might have caused this? And how a status of no airport card installed and a drive that wont boot a disk normally can be related?
I'll be getting it back on Tuesday, but i just wanted to know what the heck they might have done to have screwed things up.
Thanks
Phil
Message was edited by: Philip Dexter

Hi Phil,
I can't say for sure, but it sounds to me like they didn't reconnect the WiFi hardware when replacing the screen. To my knowledge, the Airport "hardware" (including the antenna) is located inside the screen hinge. When the screen was replaced (and the hinge not properly aligned) perhaps someone improperly connected the Airport hardware, or forgot to connect it entirely.
The reason the WiFi hardware is located in the hinge is because that is the only plastic area of the entire notebook. Radio signals do not travel well through aluminum, so some area of the computer has to be plastic to allow that signal to get through. The hinge is the only area where that's possible.
As for the reason why the machine wouldn't boot up from the disc, I have no idea. Here's hoping it does when it comes back. If I were you, I'd have a chat with Apple Customer Relations about the situation.
--Travis

Satellite L10-144 - Can't boot from Hard Disk

Similar Messages

Maybe you are looking for