Satellite L300-135 not booting into windows!

bought it about 2 years ago everything worked perfectly until today where it's even unable to boot into windows vista...I just turn it on when the windows loading bar is loading then it shows blue screen for 0.1 sec and it resets itself... even the safe mode wouldn't start and restore mode (last good known config) couldn't help it to start...i tried using an ubuntu linux live cd to save my datas but couldn't boot either, gave an error stating something as abnormal.
so where's the problem ?
Windows boot manager tried to find the problem and is telling me this:
status: 0xc00000e9
info: An unexpected I/O error has occured.

> so where's the problem ?
Who knows??? Do you think its so easy to say whats exactly wrong without running any tests???
Maybe its just a software issue but a hardware issue (RAM, motherboard, etc..) can be possible too.
As I understood your message, you want to access the data and to backup the necessary files
Well, the Toshiba recovery disk would format the whole HDD therefore you should backup the data before usage of recovery disk.
You could remove the HDD from the notebook and could connect it to another computer using an external USB HDD case.
After backup, you could use the recovery disk to reinstall the Windows.

Similar Messages

X102e - Hard drive does not boot into Windows

Hi, I was trying to reinstall Windows on my X120e.
I tried clean install with Windows 7 Professional, but the hard drive does not boot into the Windows once it has done the first phase of the install(you know, the copying part)
After the restart done by Windows, it goes as far as "Starting Windows" but does not actually boot into the Windows.
When I try to install Windows with another HDD, the device works well, but I can't swap the HDD because it is not 7.5mm think HDD.
Is there any possibility the HDD will work trough any software-level process? The HDD works fine as external HDD when tested with external HDD adapter, and installs well. only problem is that it fails to boot
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Thank you for reply.
This is not exactly the issue. I was talking about the HDD originally installed in the PC.
The PC successfully recognizes the external disk I used to install the Windows, but the problem was that I did not boot into the "First boot" screen, which basically works on the already installed data.
As of now I have installed an SSD and is working fine. strange part is that HDD works just fine when I use it as an external HDD via adapter. Strange huh?
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Machine will not boot into Windows!!

I formatted a 32 GB partition in NTFS, then successfully installed Windows XP Pro along with Leopard Bootcamp drivers. All was well. And then I tried to restart.
I held the "Option" key until the Mac OS and Windows drives showed. Selected the Windows drive and clicked on the arrow. Nothing happened except for the cursor freezing in position and the drive eventually spinning down. A light touch on the power button shut the machine down.
I have tried selecting the Windows drive as the default startup disc in System Preferences, no dice.
What have I done wrong? What can be done to repair the issue? I need help, wife about to start throwing stuff
All the best,
Chumpy

Odd thing I noticed. When installing the Windows XP Pro, new full installation disc, not repair disc, I had to shut down before installing the Leopard disc and loading Bootcamp and Leopard drivers because I ran out of time. The machine booted right into Windows the next time I tried. Then, after loading Bootcamp and drivers off Leopard disc the machine will not restart into Windows.
I have tried to do it by selecting it as the default drive and by pressing "Option" and selecting the Windows drive. Neither approach does anything. Literally. The optical drive and the harddrive eventually spin down and the machines white screen is frozen.
So, I have redone the partition in Bootcamp Assistant. When I try to boot to the installation disc now, it won't go. For some reason this is just not working at all.
Frustrated,
Chumpy

HP g6-1202sa Notebook pc does not boot into Windows

I have a HP pavilion G6 that hangs when it gets past the Windows logo and ends up with a black screen and a live arrow cursor but nothing else happens. I have gone round and round looking at various ways of dealing with it but without success. These include various rescue/boot discs, then going into command prompt to carry out various system commands. These are best described in the article and related threads at the links below:- Re: HP G72-b66US Notebook PC Dosn't Boot into Windowshttp://h30434.www3.hp.com/t5/Notebook-Lockups-Freezes-Hangs/HP-G72-b66US-Notebook-PC-Dosn-t-Boot-into-Windows/m-p/1336579#M22150 AndHow to Recover from an Infinitely Looping Startup Repair Loop without Reinstalling Windowshttp://www.sevenforums.com/tutorials/139576-startup-repair-infinite-loop-recovery.html Operations used include:-- use of Regback on DEFAULT, SAM, SECURITY, SOFTWARE and SYSTEM files- Bootrec.exebcdedit /export C:\BCD_Backupc:cd bootattrib bcd -s -h -rren c:\boot\bcd bcd.oldbootrec /RebuildBcdd
bootrec /fixmbrbootrec /fixboot Some other bits of information: - During the above operations I get the message 'Total identified Windows installations: 0'- I have copied most of the HDD to an external HDD using a SATA link and Testdisk I feel that the fault is probably a very simple fix (in the Boot directory?) but I have not found it yet.I would be grateful of your help please.Dave

my guess it's the hard drive did you ran the hard drive test as well?

Satellite C50-A0113 does not boot into windows

Hello.
I own a toshiba satellite C50-A0113 laptop running windows 8 64bit.
Ive had it for exactly two years a few days ago i restarted it and then when it starts it stops at the "Toshiba leading innovation" screen and then it says scanning and repairing drive C while on that screen it starts the process and then stops at 34%.
that was two days ago now it just gets stuck on the "toshiba leading innovation screen " then after a few minutes it says preparing automatic repair.
It then leaves that screen and goes to a black screen for a few minutes then flashes the blue screen written "your computer encountered a problem" then restarts.
I tried creating a bootable windows 8 disc in order to repair but it doesnt even boot into the usb.
I restart and press f12 in order to select the media to boot into. It checks the media goes to the toshiba screen then just goes black for some minutes untill it restarts.
May i please know what is wrong and how can i possibly fix this because the problem is clearly not my hard drive.
I removed it and put into another laptop and it was fine

Dear aya11,
Defiantly it is a operating system issue.
did you check in the BIOS mode??
if your laptop is working fine in the BIOS mode then you have to reinstall operating system.
if you have preloaded operating system then you can recover your operating system.
recovery option is :*
if you are using window 7 in your laptop then,
just restart your laptop and hold the "0" numeric key..u get option HDD recovery just enter in HDD recovery
then it showing popup for format laptop just click on the yes ..you get a next option and your laptop is getting restart.
if you are using window 8 in your laptop then
just restart your laptop and hold the "F12" numeric key..you get option HDD recovery just enter in HDD recovery
then it showing popup for format laptop just click on the yes ..you get a next option and your laptop is getting restart.
in case both option is not working then u have install a new OS.
Thnx :)

Dell Precision M6400 will not boot into Windows

I started up a computer we haven't used in a few months and received this message on a black screen. "Intel(R) Matrix Storage Manager option ROM v8.0.0.1039 ICH9M-E Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
Steps already taken:
Booted into BIOS and ensured that the HD was selected as a boot device.
Took battery out and discharged power and then restarted
I am not sure what I can do next. But I've got a hunch that the HD has failed. But is there anyway to test that?
Thanks,
TR
This topic first appeared in the Spiceworks Community

I started up a computer we haven't used in a few months and received this message on a black screen. "Intel(R) Matrix Storage Manager option ROM v8.0.0.1039 ICH9M-E Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
Steps already taken:
Booted into BIOS and ensured that the HD was selected as a boot device.
Took battery out and discharged power and then restarted
I am not sure what I can do next. But I've got a hunch that the HD has failed. But is there anyway to test that?
Thanks,
TR
This topic first appeared in the Spiceworks Community

Re: Satellite L300 - Will not boot up

Hi, I'm really hoping someone can help me.
When I turn the laptop on it goes straight to a black screen that offers the opton to "Launch startup repair" or "Start windows normally". However when I chose start windows normally it looks like it is going to start and then goes straight back to the same screen. When I chose the startup repair it goes to a command box for about 30 seconds and then a box saying the installed programe cannot start, click ok to turn off the computer.
I have tried starting the system in safe mode and at the last known good configuration, but the same thing happens every time and it seems that it just doesn't want to boot at all. I am really worried because all my important files are on the recovery D drive but I cant get to them.
Any ideas?

I believe your problem would be that the boot files are corrupted on the beginning of the hard drive.
To solve this you will need to locate a boot CD of your operating system. this when run on your laptop will start it up to an area were you can repair windows. failing this you might like to obtain a copy of hiren boot disc 10.5. This will allow you to boot into a mini windows running in the ram of the laptop and enable you to retrieve your data to an external hard drive. failing all this you can purchase a upgrade windows7 disc from a computers store for about $130 which will reestablish the boot files and reload windows without loosing data.

MacBook Pro will not boot into Windows 7.

I am sorry if this has been discussed before, but I could not find a correct answer. I recieved my 15" MacBook Pro last week, and I swapped out a few of the inside's for upgrades. I replaced the optical drive with a NewMode 2nd HDD Caddy, and a Hitachi 750 GB 7200RPM HDD. I also upgraded the RAM to 8GB. I bought the HDD so I could put Windows 7 on it. I went through the bootcamp process, partitioned 90 GB of my 2nd drive, and rebooted with my Windows 7 CD in my external CD drive. When it rebooted, it went to this black screen with a blinking cursor. I have tried many different ways to boot to the CD; like rEFIt and option key with no luck. It is not the disc because I have tried many bootable discs and none of them have worked.
Any help would be appreciated Thnx.

You cannot boot Windows from an external device. The Windows installer and Windows itself must be booted from an internal optical drive.
You can do some Google searching on how to create a bootable USB flash drive for installing Windows, but they all will require access to a Windows machine.
The new Boot Camp Assistant does provide an option for creating a bootable USB flash drive, but I don't know if it requires that the Windows installer DVD be in an internal optical drive.

MSI K9A2 Platinum + Phenom 9600 + 2GB Mushkin XP8500 cannot boot into windows

Hi!
I am building my computer using the Spider platform and I ran across problems during booting into windows.
I am using MSI K9A2 platinum with Phenom 9600 and Mushkin 2Gb kit XP8500 ddr2 1066. I have no problem installing windows xp.
The problem starts when I install the utility and drivers that come on a cd from MSI, my computer requests to re-boot after installation and after
that it will not boot into windows. I can get to the windows logo and then the system reboots right away.
I checked the bios and it shows that the ram is running at 800mhz and i have tried running with just 1 stick and im getting the same problem every time.
Anyone knows how to resolve this?
thanks!

Quote from: nirianto on 22-February-08, 01:32:52
Everything is stable now...I guess installing the driver from the MSI website is the best thing to do right now
I notice that my ram is underclocked to 800mhz instead of 1066mhz...I have update the motherboard BIOS to v1.2 and i checked that the ram is running on unganged mode...I tried adjusting the spd to 5-5-4-12 with voltage of 2.2v as suggested by the mushkin ram itself
Any idea?
"I have update the motherboard BIOS to v1.2 and i checked that the ram is running on unganged mode..."
That is the correct mode.
"I notice that my ram is underclocked to 800mhz instead of 1066mhz..."
1066 is not officially certified by JEDEC, also your memory probably don't have SPD configuration for that freq.
Contact to Mushkin for more details.
"I guess installing the driver from the MSI website is the best thing to do right now"
Yep
"Everything is stable now.."
nice :smiley:

MAX shows PXI card when booted into Windows but not in Hypervisor mode

Hello again all you helpful forum-goers!
I'm having some difficulties with a Hypervisor system seeing the two Pickering 6 channel programmable resistor cards that are loaded into the PXI chassis. When I boot into Windows mode, MAX sees them under the My System just fine. When I then run the Hypervisor configuration software, I see them both listed, and have them assigned to the Real-Time OS. However, when I then boot into Hypervisor mode, MAX does not see them under the Remote Systems -> Hypervisor Target -> Chassis (or anywhere else), and the drivers report not seeing any modules either when I debug my code running on the real-time system.
Does anyone have any idea what setting or configuration I might have incorrect? Is there any other information I can provide that would be relevant or useful to answer this question? I'm not the main hardware guy, he just got married and so isn't available, so I'm out of my comfort zone. ;-) I write the software that runs on the system, though, so I'm not completely clueless. I know we just replaced the controller in the main chassis with a faster one (unfortunately I don't have the number on hand, the simulator is down in the lab), but I also know we are using that same controller and Pickering card on a different simulator and it is working just fine.
Any ideas? I very much appreciate your time!
-Joe
Solved!
Go to Solution.

Nevermind, the answer turned out to be that I did not have the drivers fully installed on the real-time system. Apparently that caused it to not recognize the cards. I never did figure out / remember exactly how to install the Pickering drivers on the real-time side, but fortunately I was able to just copy all the files that had "Pickering" in their name from the C:\ni-rt\system folder of the real-time file directory from another simulator to this one. ;-)
Cheers!

Cannot boot into Windows XP, should I replace hard drive?

THE PROBLEM: I have not been able to boot into or use Windows XP (SP2) for almost 3 years. I have been using Linux instead for 3 years and am using it now. The Windows Recovery process only half works, it works up until you have to boot up the computer from the hard drive. Then it no longer works. The computer will load the files from the TOSHIBA Recovery and Applications/Drivers DVD that came new with the computer onto the hard drive. But when you get to the point of booting off the hard drive, with newly added Windows & Toshiba files, nothing happens. It does not boot up into Windows XP. In fact I can see the newly added Windows & Toshiba fileson the hard drive when I boot into Linux (Live) off the hard drive.
THE HARD DRIVE (Specs below): I ran a SMART Data check using a Linux (Ubuntu) Disk utility on the hard drive and it passed everything except for Reallocated Sector Count. There are 20 bad sectors. I called the Toshiba 800 # on the DVD and they told me that the problem may be the hard drive. A new TOSHIBA Recovery and Applications/Drivers DVD costs $40. Toshiba also said there is no Windows XP Recovery Console on the DVD.
CAUSE OF THE PROBLEM: I think, and TOSHIBA agreed it is either the hard drive or corrupteD files on the TOSHIBA Recovery and Applications/Drivers DVD
POSSIBLE SOLUTIONS: I have found a couple of sites that seem to have instructions for making a Windows XP Recovery Console CD. And I have thought I might try to run some Windows XP Recovery Console commands from such a CD, such as fixboot, fixmbr, etc. The try to see if I can boot into Windows XP from the hard drive. If I can, then that might suggest he problem is corrupted files on the TOSHIBA Recovery and Applications/Drivers DVD. If I still cannot boot into Windows, then maybe I should replace the hard drive. This should be very easy to do.
QUESTION(S): Does anybody have any comments or suggestions? Does my approach sound good? Do you have any other suggestions?
I have a TOSHIBA Satellite L25 S1216 that I bought new in early 2006. It has a 40 GB (5400 RPM) Enhanced IDE (ATA-6) 9.5 mm height hard disk drive in it. User removable, i.e., it is easy to replace.
Thank you,
Bob
Solved!
Go to Solution.

My plan is to try to use the TOSHIBA Recovery and Applications/Drivers DVD to load the WIndows XP files onto the hard drive, then use the Windows XP Recovery console CD I downloaded from here
http://www.proposedsolution.com/downloads/download-windows-recovery-console/
by using commmands such as fxmbr, fixboot, etc to see if I can get the computer to boot up into Windows XP.
Good plan, Bob!
Description of the Windows XP Recovery Console for advanced users
A backup plan would be to obtain a Windows XP installation CD from eBay or wherever. They are super cheap now. Then you could install Windows clean and add the drivers and utilities from the website here. Or you could use it to repair-install Windows.
How to Perform a Windows XP Repair Install
You are entitled to activate Home Edition for free. I understand that even after Microsoft no longer supports Windows XP (in April), they will honor activation attempts.
I wouldn't mess with SSDs. And stick with IDE PATA drives. You won't need to worry about advanced-format technology since that didn't come along until the very recent SATA drives. Your BIOS should support 120GB (KB303013). Some here.
-Jerry

Can't boot into Windows??

Hi!! This is my theory about not being able to boot into windows. If you have made a system repair disc like you should have made on day one; and your PC will not boot with the system repair CD, you probably have some serious hardware problems.
I'm going to steal this reply from cee64 again. A system repair CD can be made from any PC that is running W7 ect.
Hi I'm going to steal this reply from cee64. I'm sure he won't mind!
"It is quite possibly the hard drive is failing or has failed. The reason you can't get into the bios or boot from a CD/DVD is because the bios it hanging trying to recognize the hard drive. Try removing the hard drive and see if it will allow you into the bios or boot to a CD/DVD. If it does, go the hard drive manufacturer's support site, downlod their hard drive diagnostic ISO image, then use the burn from image option to create the self booting cd, then boot to it and run the most exhaustive diagnosis on it if it will boot. If you can't get it to boot to the diagnostic disk while the hard drive is installed you'll more than likely need to replace the hard drive.
If it won't get you into the bios or boot to a CD/DVD with the hard drive out of the system you need to try reseating the ram. If that doesn't help you probably have a bad motherboard. In this case it would more than likely be cheaper to just replace the laptop than fix it."
http://www.dummies.com/how-to/content/how-to-use-a-system-repair-disc-to-restore-windows.html
If Seatools found your HD good, then you have a good chance of using the recovery disks or the recovery partion to restore you back to factory setting. If that fails, you may be down to a bad motherboard. I know of no program to test the MB. You can use memtest 86 to test your Ram. I think it tests some parts of your MB, but can't say that for sure.
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Hi! I stole this reply from Jerry Edited One link, because it failed to open
Let's start here. The spec above says your machine came with 32-bit Windows Vista. Have you changed it?
We need to reach the recovery environment. Can you do it this way?
http://windows.microsoft.com/en-US/windows-vista/What-happened-to-the-Recovery-Console
If not, burn a system repair disc from this download (assuming 32-bit Windows).
Download Windows Vista Recovery Environment ISO X86 version (32 bit)
-Jerry
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Satellite L500D won't boot up Windows Vista

Hi. I have a Satellite L500D which failed to boot up Windows Vista (Home Premium). It shut down normally the previous night, with no power interruptions or other abnormal events during shutdown. The following day, it failed to boot Windows and went into a diagnostic screen. This diagnostic attempted to resolve and fix the problem, but failed. It didn't give me the option of Windows "Safe Mode" either.
As the laptop was under warranty, I returned it to the retailer. By hitting F8 at bootup we got into Safe Mode, then copied my folders to an external hard drive. They then "recovered" the laptop (not sure if that meant re-formatting the hard drive and re-installing Vista?)
Q. Has anyone else experienced this problem, and is there a preventative measure?
I would really appreciate any advice on this problem.
Regards
Mark Brymner
Solved!
Go to Solution.

You asked if that has ever happened to someone before. It's almost like asking if you ever had a flat tire. It's happened to someone at least once, or in my case, many of times.
You didn't mention if there was a specific error code, but most failure to boot into Windows problems are because of a corrupt or missing boot file(s). I know within the last few months, Microsoft has pushed some updates that cause people's machines not to boot properly. There really is nothing you can do about it. Just ensure you are not shutting the machine down while the computer is updating.
Keep your important documents/pictures/music backed up just in case.

Can only boot into Windows 7. Can't even boot from Snow Leopard DVD.

I have no idea what prompted this. I don't recall installing any OS updates recently, other than some Windows Live apps in Windows 7.
I have an early 2009 Mac Mini with Snow Leopard, and have Windows 7 64-bit installed in a Boot Camp partition. When I installed Windows 7, I couldn't get the Boot Camp utility to install within Windows (I guess because it's 64-bit) so to switch back and forth between OSes, I just shut down the Mac and restart it with the Option key pressed, and select Mac OS X when I want to return to Mac. This has worked for about a month and a half now (ever since I got Windows 7). Suddenly I have problems.
I first had problems booting into Windows or Mac. I got to the grey screen with the Apple logo, with that spinning "progress" thing going for a while, then it would freeze up and get stuck on the grey screen with the Apple logo. I zapped the PRAM. No help. Then, after disconnecting all external drives (I have several) and extra USB devices, I was able to boot from the DVD install disk and reinstall Snow Leopard on my internal drive. Joy, or so I thought. Then I booted into Windows 7, and after some weirdness getting it to start, it did successfully start and ran just peachy.
Then I turned off the Mac and held down the option key (as usual) to return to Mac OS. But now all that happens is that I get a grey screen for a few seconds, then the Mac boots back into Windows 7, which seems to work fine. (I'm in Windows 7 right now.) I turned on one my external drives (Snow Leopard installed, connected via Firewire 800) in hopes that the Mac would boot into that, but same thing. Ignored and back to Windows 7.
Then I thought I'd boot from the install DVD again by putting it in the drive and holding down the C key as I restart, but the same thing--a grey screen for a few seconds, and then booting right into Windows 7. I can't seem to escape Windows 7! It's a bit disturbing when it won't even recognize the install DVD.
I tried to call Apple Care since I'm within my 90 day support window, but of course they are closed. I'm figuring that I'm going to have to take this into an Apple Store, but thought I'd see if anyone has any ideas. Any advice will be appreciated. Thanks.

According to Apple, Win 7 64bit is supported with Bootcamp 3.0. If bootcamp 3.0 is available; I could not find it anywhere on Apple's website. It appears the most recent version is 2.2. The only place I could find 3.0 is not on Apples website and it's a questionable source so I won't post it here.
It may just be a matter of time before Apple makes it available. I'm not suggesting you wait, however if the install disk can't be used, I'm not too sure where u could go from there. Calling Applecare might work.
If you do a simple google search using the terms 'download bootcamp drivers windows 7' u will see what I was referring too.
Here's what I found from Apple (It doesn't specifically mention 64bit however just win7): http://support.apple.com/kb/HT3920
This is not from Apple, but specifically addresses whether they support win7 64bit: http://www.macnn.com/articles/09/08/31/boot.camp.win.7.64.support/
Here is more info about bootcamp 3.0 and win7: http://www.apple.com/support/bootcamp/

Black screen when trying to boot into Windows 7

Hello everyone.
Today we've encountered an issue with one of our MacBook Pros with Windows 7 installed. The computer was booted into Windows 7 (it's strictly used as a Windows machine by this particular user) and after a time of inactivity it went to sleep. It wouldn't wake up from it's sleep so we tried a hard boot. At that point we would get the grey screen, the Apple tone wouldn't sound off and it would just go to a black screen (by default we have it booting to windows). So then we reset the PRAM. Now, we get the apple tone and we can boot into the Mac side. But when we try and boot into Windows, we get a blank screen.
What's even more interesting, if I try and boot into a Windows install disk to do a boot repair, it gives me a black screen. If I even try to boot from a live Linux cd, I get a blank screen! When important thing I then noticed was that the cd spinned for a couple minutes, then stopped. So I began to wonder if it was still loading the OS like expected, but just wasn't displaying it.
So I booted into Windows, got the blank black screen. Then I went into another computer, fired up remote desktop and voila! I'm in the machine!
So the problem is this: When booting into ANYTHING other than OS X, the display turns off.
What can we do?

Hello there,
I have a similar problem! Windows 7 shutdown unexpectedly and since that I can not reboot in windows anymore only with safe mode where everything is a mess.
Also when it's trying to reboot in windows a blue window appears,says something about drivers and it is counting something (79.78...till100)but I m not able to read it cause it disappears immidiately and then black screen and then it turns to reboot in mac which works fine.
I m sorry if I confused you with my english...
If anyone knows please help!
Thanks

Satellite L300-135 not booting into windows!

Similar Messages

Maybe you are looking for