Satellite L300-15V - The system cannot install Wireless LAN driver

After installed all drivers for that machine, the system shows that it need to install Wireless LAN driver, but i did!!! What's going on? Help! I can't make wireless net home!!!!!!

I assume you have tried to install the Realtek WLan driver. Is it right?
Go to this Toshiba WLan driver page:
http://aps2.toshiba-tro.de/wlan/
and check if you can install the Atheros Wireless LAN driver or the Intel PRO/Wireless 3945/4965/5100/5300 driver.
Greets

Similar Messages

The system cannot find my hard drive - is it broken?

I recently updated to OS X 10.4.4 and everything was fine. But today the system froze and I couldn't do anything but press the on/off switch to quit. After that I couldn't boot the system normally. If I start from the System-DVD and open the disk utilities the Hard Drive is not displayed so I cannot check the volume. What can I do?
G3 iBook 600 MHz 640 MB SDRAM Mac OS X (10.4.4)

Hi Berndt, thank you very much for your advice. I think too it's something different and not the HD. After resetting the iBook (vram, pram, pmu etc.) and after a while waiting the system started yesterday without any problem. So I could make a backup. But this morning I had the same phenomenon - frozen Screen (only the cursor worked) and I have to reset everything again. I think I will give it to gravis for an inspection. But I don't want invest too much. A new (bigger) HD would be fine but I don't know what else could be broken and how much the components are. What do you think?
Ronda. I bought my iBook with an OEM Version of diskwarior 2.1.1 which doesn't work with OS-X. I looked at Alsoft but there is no download update available - I have to buy an Upgrade tp Version 3.0 for 39 quid and it takes 3-4 weeks shipment. Do you know an alternative?
G3 iBook 600 MHz 640 MB SDRAM Mac OS X (10.4.4)

G50-30 Error when installing Wireless LAN driver in windows 8.1

HI, I updated my G50-30 laptop with the new wireles LAN driver from Lenovo updates program (july 29, 2015), after restarting my device the" wifi" stop working, Do you know how I can reverse that or how to fix it, I downloaded the driver from Lenovo Help support web page but did not work. Any suggestions? Fernando

Hi Satya14,
Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I saw your post regarding the error message you are getting and “Error 1722” is a Windows Installer error. Here is a Microsoft Answers link with a couple of potential solutions why they didn't work for original poster it seems to be the general consensus from my research.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Cannot enable Vista Aero on Satellite L300-15v with Intel CPU

I installed Vista for my Satellite L300-15v which i bought without system.
I can't set HIGHER memory for the graphics ( shared ) memory which is between 0 and 256.
Please notify me how to do this and whether this is the reason why Aero effects doesn't work *or my pc doesn't meet the minimum requirements*.
note: L300 is 2.13 celeron | graphics: Intel 965 - GMA X3100 , 2GB of Ram
thanks in advance
Message was edited by: omda430

Hi
Firstly you should check if your Vista version would support Aero.
Windows Vista Home Basic doesnt support Aero.
So you need a higher version of Vista to use such feature
Please also check this Microsoft page: [Troubleshoot problems with Windows Aero|http://windowshelp.microsoft.com/Windows/en-US/Help/c33fe91a-9e6f-41f4-ae82-3ed2d5fa2fbf1033.mspx#EZD]
Greets

"The system cannot find the path specified." error message when trying to start instaling a software

hi
when i trying to install a software for example CAD Viewer software, my windows show this message : The system cannot find the path specified
i use the windows 7

Zohre
What version of the CAD software are you trying to install? Is it compatible with win 7? Older installations (on older OS) installed to a different default location that win 7 does not have.
Wanikiya and Dyami--Team Zigzag

RSAT won't install on Windows 8.1 Pro - "The system cannot find the file specified."

Please help. RSAT won't install on Windows 8.1 Pro. Every time I try, I get the same error - "The system cannot find the file specified.". I really don't want to have to refresh the PC to get it working! I've installed the update successfully on
a fresh win 8.1 enterprise install on a Hyper-V VM.
I am in uk, so have installed the en-US language pack first. I did have a windows component store corruption but I've managed to fix that.
event log says:
Windows update "Update for Windows (KB2693643)" could not be installed because of error 2147942402 "The system cannot find the file specified." (Command line: ""C:\Windows\system32\wusa.exe"
"C:\RSAT Windows8.1-KB2693643-x64.msu" ")
CBS log (C:\Windows\Logs\CBS\CBS.log): http://1drv.ms/19CAv14

As Roger Lu reported, the log indicates that there is corruption in the update files that you downloaded. The log actually reports “file not found”, so you may also want to check permissions on the extracted files in C:\Windows\SoftwareDistribution\Download\76ecaa86ec6712300c2d71cbcdad378c\.
You can also re-try downloading the files to see if your original download was just corrupt.
Bruce Wooding Windows Outreach Team- IT Pro Windows for IT Pros on TechNet
It was a permissions issue! Thanks so much Bruce!
I checked the permissions for the folder mentioned above and TrustedInstaller only had List Folder Contents and Special Permissions. So I granted granted Read & Execute to TrustedInstaller and tried installing again...
1) double clicked the installer.
2) once it said Initialisation was complete, I checked the permissions again and it had re-set them to as before, so I granted Read & Execute to TrustedInstaller again
3) Installation was successful.
Not really sure why this happened as it doesn't make sense but it's working now :-)

Cannot Install this Hardware - The system cannot find the file specified.

I got an 8G ipod touch last week. When I plug it into USB port on my PC, a Found New Hardware Wizard box pops up with "Cannot Install this Hardware", "There was a problem installing this hardware: Apple Mobile Device USB Driver", "An error occurred during the installation of the device", "The system cannot find the file specified.", "Click Finish to close the wizard.". If I go ahead and click finish, the device disappears and a couple of seconds later tries to install again and the box pops up again. However, if I leave the box alone, the ipod does actually appear in itunes and I can sync music to it, so all is not lost Any ideas though how to stop this error box popping up? The USBAAPL.SYS driver exists - I don't know what file it cannot find. Thanks.

Hi and welcome to Discussions,
if you have a Leopard OSX DVD you can use it to install the BootCamp 2.0 drivers and later use the BC Update 2.1 for XP to further update the drivers.
If not (still running OSX Tiger) there are two possibilities:
use this direct download link for the latest ATI/AMD Mobility Driver package http://ati.amd.com/online/mobilecatalyst/
or use the ModTool found here http://www.driverheaven.net/modtool.php in conjunction with the ATI/AMD Desktop Driver package.
You should also consider getting and installing the latest (June 2008) DirectX 9 package from Microsoft.
Hope it helps with your gaming problems.
Stefan

"The system cannot find the path specified" error when installing a network printer running Win 7

Some of the end users are having issues when trying to install network printers. We have created a portal where they can locate the printer they want to connect to, click connect, and the printer will download with the correct drivers on their PC's. The
entire company is running Win 7 for their operating system. One end user in particular has had issues installing multiple printers from the portal, when I go to test installing these same printers on my PC, they all install successfully. trying to figure out
why some end users hav issues with installation and others do not. They will get the error, The system cannot find the specified path. Any help would be great

Hi JeffWilko,
What is your current situation?
To receive better analyzation, please provide more details?
1. Could you explain a bit about the sentence ‘installing multiple printers from the portal’ ?
2. Check the event viewer and share us the related error log.
Please take the following steps for troubleshooting:
1. Ping the printers
2. Check if there are network firewall to block the access
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Error "The System cannot find the specified" when installing XI3.1 FP1.3

Error "The System cannot find the specified" happened when installing XI3.1 FP1.3 to client machine, however the installation is OK to server.
After the error, go to Control Panel -> Add or Remove Programs, and observe.
BusinessObjects Enterprise XI 3.1 Client Tools is installed,
but BusinessObjects Enterprise XI 3.1 Client Tools Japanese Language Pack is not.
And Language Pack install log is not written.
The same error happened when installing .net2.0.
The installation for FP1.2 is OK.
Would you tell me what reason probablely this issue is?
Thanks.

Hello Sarah,
I recommend to post this query to the [BusinessObjects Enterprise Administration|BI Platform; forum.
This forum is dedicated to topics related to administration and configuration of BusinessObjects Enterprise, BusinessObjects Edge, and Crystal Reports Server.
It is monitored by qualified technicians and you will get a faster response there.
Also, all BOE Administration queries remain in one place and thus can be easily searched in one place.
Best regards,
Falk

VSTO 2010 Addin installed on Outlook 2007 Machine: Giving binding error - 0x80070002. The system cannot find the file specified (Fusion Log).

Fusion log:
The operation failed.
Bind result: hr = 0x80070002. The system cannot find the file specified.
Assembly manager loaded from: C:\WINDOWS\Microsoft.NET\Framework\v4.0.30319\clr.dll
Running under executable C:\PROGRA~1\MICROS~2\Office12\OUTLOOK.EXE
--- A detailed error log follows.
=== Pre-bind state information ===
LOG: User = XP-2007\Administrator
LOG: DisplayName = Blue Jeans Outlook Addin, Version=3.0.233.24954, Culture=neutral, processorArchitecture=MSIL
(Partial)
WRN: Partial binding information was supplied for an assembly:
WRN: Assembly Name: Blue Jeans Outlook Addin, Version=3.0.233.24954, Culture=neutral, processorArchitecture=MSIL | Domain ID: 2
WRN: A partial bind occurs when only part of the assembly display name is provided.
WRN: This might result in the binder loading an incorrect assembly.
WRN: It is recommended to provide a fully specified textual identity for the assembly,
WRN: that consists of the simple name, version, culture, and public key token.
WRN: See whitepaper http://go.microsoft.com/fwlink/?LinkId=109270 for more information and common solutions to this issue.
LOG: Appbase = file:///C:/Program Files/Blue Jeans/Outlook Addin/
LOG: Initial PrivatePath = NULL
LOG: Dynamic Base = NULL
LOG: Cache Base = NULL
LOG: AppName = OUTLOOK.EXE
Calling assembly : (Unknown).
===
LOG: Start binding of native image Blue Jeans Outlook Addin, Version=3.0.233.24954, Culture=neutral, PublicKeyToken=null.
WRN: No matching native image found.
LOG: IL assembly loaded from C:\Documents and Settings\Administrator\Local Settings\Application Data\assembly\dl3\LZMMEM67.CTT\397DNQ77.1W9\c337c5e7\0023f77f_891ed001\Blue Jeans Outlook Addin.dll.
The required correct settings file is present in the location C:\Program Files\Blue Jeans\Outlook Addin but the .NET created user.config in AppData have wrong entries. The machine is installed with VSTO 2010 and .NET 4.0 Client Profile. Also the KB 976477 is
already installed the registry entry EnableLocalMachineVSTO (KB 976811) is made. May someone please give me a clue on why the user.config file is created with wrong entries and also, why this assembly binding error happening?
Thanks in advance.
Prasad

this might help:
https://social.msdn.microsoft.com/Forums/vstudio/en-US/2601334c-d5cb-4f51-a99a-4d8ea9217938/userconfig-file-problem-after-upgrading-to-outlook-2010-from-2007?forum=vsto
VSTO Word add-in user.config lost every update

Won't Install in Win XP "The system cannot open the device or file specifie

When installing Quichktime or iTunes, the installer displays ""The system cannot open the device or file specified."
What should I do?

I was getting this problem too. To resolve I did the following.
Physically disconnected PC from network.
Stopped Anti Virus (Evira personal).
Turned off Windows Firewall.
Stopped Malware detection (PrevX).
Installed iTunes + Quicktime.
Restarted above security programs.
Reconnected to network.
Problem sorted.

The system cannot find the specified file

I have tried to download and install a driver for hp officejet 4500 wireless on 2 different computers, one windows 7
the other windows 8, with no sucess. I keep getting a message saying " The system cannot find the specified file".
I even paid for a driver on a disk and got the same message.
HELP ME PLEASE
Sincerely
meyerret

Hi,
Follow the steps below and check if that resolve the issue:
1. Open Mcafee software, from the Virus and Spyware Protection section click on Schedule and run scans. Click on Real time scanning and then on Turn Off. select till I restart the PC and confirm by clicking the Turn Off button.
Now try reinstalling the HP Software and check if the installation goes as expected.
If the issue persists continue following the next steps below:
2. Open the run dialog by clicking both the Windows key and the R key on your keyboard. Type %windir% and click on OK.
3. Type hpoins*.dat into the top search bar, if there are any results rename the extention into old instead of dat. (e.g. hpoins1.old)
4. Type hpwins*.dat into the top search bar, if there are any results rename the extention into old instead of dat. (e.g. hpwins1.old)
5. Launch the Run dialog by clicking both the Windows key and the R key on your keyboard. Type MSIEXEC /UNREGISTER into the Run dialog and click on OK.
6. Launch the Run dialog by clicking both the Windows key and the R key on your keyboard. Type MSIEXEC /REGSERVER into the Run dialog and click on OK.
7. Run the installation file and check for any difference.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Error message on my development workstation: The system cannot find the file specified.

Post Author: cseverin
CA Forum: Crystal Reports
Hi,
I am currently developing an ASP.NET website using Visual Studio.NET 2005. I am using the .NET 2.0 framework, VB.NET as my programming language and I connect successfully to a SQL Server 2005 database. I can select, insert, update and delete data from the database elsewhere in my project, so I know basic connectivity isn't an issue. The problem seems to be with Crystal Reports.
I created a folder called 'Reports' in my project and added a Crystal Report file (OpenFiles.rpt) to it. I designed the report and initally used a hard-coded SQL query as its datasource so I could quickly get the database fields onto the report and preview them. All worked fine.
To make the report accessible to the rest of the website, I created an .xsd dataset file containing the three tables (and their corresponding tableadapters) that the report requires and then redeveloped the report using the dataset as the datasource for the report. After doing this, the preview no longer worked.
Next, I added a page to the website and dragged a Crystal Report Viewer Control onto it. In the code behind the page I wrote:
Option Strict On
Imports System.Data
Imports CrystalDecisions.CrystalReports.Engine
Imports CrystalDecisions.Shared
Partial Class Reports
     Inherits System.Web.UI.Page
     Private objOpenFilesreport As OpenFilesReport
     Private rptOpenFiles As ReportDocument
     Private strLastErrorMessage As String = Nothing
     Private errLastException As Exception = Nothing
     Dim strFileKey As String
     Dim strJurisdictionCode As String
     Dim strStaffId As String
     Dim strReportId As String
     Private Sub ConfigureCrystalReports()
          Dim reportPath As String = Server.MapPath("OpenFiles.rpt")
          Dim rptopenfiles As New ReportDocument
          rptOpenFiles.Load(reportPath) <== I checked this during execution and the value correctly points to the OpenFiles.rpt file in the Reports     folder of my project
          Dim ConnectionInfo As ConnectionInfo = New ConnectionInfo()
          ConnectionInfo.DatabaseName = my database
          ConnectionInfo.UserID = login id of user
          ConnectionInfo.Password = user's password
          SetDBLogonForReport(ConnectionInfo, rptopenfiles)
          CrystalReportViewer1.ReportSource = rptopenfiles
     End Sub
     Protected Sub Page_Init(ByVal sender As Object, ByVal e As System.EventArgs) Handles Me.Init
         ConfigureCrystalReports()
     End Sub
     Private Sub SetDBLogonForReport(ByVal ConnectionInfo As ConnectionInfo, ByVal myReportDocument As ReportDocument)
          Dim myTables As Tables = myReportDocument.Database.Tables
          For Each myTable As CrystalDecisions.CrystalReports.Engine.Table In myTables
               Dim myTableLogonInfo As TableLogOnInfo = myTable.LogOnInfo
               myTableLogonInfo.ConnectionInfo = ConnectionInfo
               myTable.ApplyLogOnInfo(myTableLogonInfo)
          Next
     End Sub
End Class
I added a hyperlink to one of the existing pages on the website to navigate to this page with the report viewer on it. When I run the website in Visual Studio and click on the hyperlink I get the following:
Server Error in '/MyTest' Application.
The system cannot find the file specified.
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Runtime.InteropServices.COMException: The system cannot find the file specified.Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace:
[COMException (0x80004005): The system cannot find the file specified.
]
   CrystalDecisions.ReportAppServer.ClientDoc.ReportClientDocumentClass.Open(Object& DocumentPath, Int32 Options) +0
   CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.Open(Object& DocumentPath, Int32 Options) +126
   CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.EnsureDocumentIsOpened() +442
[Exception: Load report failed.]
   CrystalDecisions.ReportAppServer.ReportClientDocumentWrapper.EnsureDocumentIsOpened() +513
   CrystalDecisions.CrystalReports.Engine.ReportDocument.Load(String filename, OpenReportMethod openMethod, Int16 parentJob) +1378
   CrystalDecisions.CrystalReports.Engine.ReportDocument.EnsureLoadReport() +149
   CrystalDecisions.CrystalReports.Engine.ReportDocument.get_DataDefinition() +85
   CrystalDecisions.CrystalReports.Engine.ReportDocument.get_ParameterFields() +158
   CrystalDecisions.Web.CrystalReportSource.BindControlParameter(Parameter parameter) +130
   CrystalDecisions.Web.CrystalReportSource.DataBindParameters() +191
   CrystalDecisions.Web.CrystalReportSource.EnsureParameters(Boolean forceDataBind) +90
   CrystalDecisions.Web.CrystalReportSource.LoadCompleteEventHandler(Object sender, EventArgs e) +47
   System.Web.UI.Page.OnLoadComplete(EventArgs e) +96
   System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +4086
Version Information: Microsoft .NET Framework Version:2.0.50727.832; ASP.NET Version:2.0.50727.832
Any ideas, anyone?
Also, assuming I can get past this error, I will need to figure out how to fill the tables in the .xsd dataset file. I have written a class for the dataset that includes functions that populate the tables in the dataset from the database by executing SQL queries. But how do I call these functions at the time the report is run?
This is my first Crystal report written in .NET and I've been struggling with it for days now. Any help would be most appreciated!
Thanks very much!
Chris Severin

hello, the error message is obviously coming from one of the installed mcafee extensions. please directly contact mcafee technical support - they can likely give you more detailed guidance and are the only ones who can fix bugs or make necessary adjustments in the addon.

Java.lang.Error: java.util.zip.ZipException: The system cannot find the fil

I got maven 221 installed
i got jdk 1.6 and 1.5 installed (have tested both)
I have a strange error. All my co-workers can build but I cant. The only thing I can find is that I dont have installed BEA Weblogic but I dont want to have that installed. It should be able to run anyway.
Could someone tell me what is wrong? If you need pom.xml I got that one as well.
process-classes:
[copy] Copying 4 files to C:\hudson\jobs\albpm_ip-identity-asserter_-_Build\workspace\target\mbean-content
[mkdir] Created dir: C:\hudson\jobs\albpm_ip-identity-asserter_-_Build\workspace\target\mbean-jar
[java] Creating an MJF from the contents of directory C:\hudson\jobs\albpm_ip-identity-asserter_-_Build\workspace\target\mbean-content...
[java] Compiling the files...
[java] Creating the list.
[java] Doing the compile.
[java] WLMaker-SubProcess: : Exception in thread "main" java.lang.Error: java.util.zip.ZipException: The system cannot find the file specified
[java] WLMaker-SubProcess: :      at weblogic.management.commo.BeanGenDriver.getManagementTempDir(BeanGenDriver.java:93)
[java] WLMaker-SubProcess: :      at weblogic.management.commo.BeanGenDriver.main(BeanGenDriver.java:117)
[java] WLMaker-SubProcess: : Caused by: java.util.zip.ZipException: The system cannot find the file specified
[java] WLMaker-SubProcess: :      at java.util.zip.ZipFile.open(Native Method)
[java] WLMaker-SubProcess: :      at java.util.zip.ZipFile.<init>(ZipFile.java:203)
[java] WLMaker-SubProcess: :      at java.util.jar.JarFile.<init>(JarFile.java:132)
[java] WLMaker-SubProcess: :      at java.util.jar.JarFile.<init>(JarFile.java:97)
[java] WLMaker-SubProcess: :      at weblogic.management.commo.BeanGenDriver.getManagementTempDir(BeanGenDriver.java:90)
[java] WLMaker-SubProcess: :      ... 1 more
[java] WLMaker-SubProcess: : Stopped draining WLMaker-SubProcess:
[java] WLMaker-SubProcess: : Stopped draining WLMaker-SubProcess:
[java] BeanGen code generation failed
[HUDSON] Archiving C:\hudson\jobs\albpm_ip-identity-asserter_-Build\workspace\pom.xml to C:\hudson\jobs\albpmip-identity-asserter_-Build\modules\dk.skat.ip.integration.albpm$ip-identity-asserter\builds\2010-11-2213-41-28\archive\dk.skat.ip.integration.albpm\ip-identity-asserter\1.2\pom.xml
[INFO] ------------------------------------------------------------------------

from my experience, using weblogic jars can be a pain if the full install is not on the local box.
Note that you dont have to 'install' it. Just copy the directory.
Reason is that the jar files have manifests with relative classpaths.
For an example of horror take a look at the weblogic.jar MANIFEST's classpath entry.
-Fred

I performed a software update and the system is installing an update but it has been running for over 24hrs and keeps saying "This may take a few minutes, don't shut down your computer" Can anyone help?

I performed a software update and the system is installing an update but it has been running for over 24hrs and keeps saying "This may take a few minutes, don't shut down your computer" Can anyone help?

Hello cor-el, thanks for your reply. I changed my settings for downloads to desktop and it has appeared on there. When I double click I am asked which program I want to open file. I click firefox and another box "opening install" says I have chosen to open the file which is an application and do I want to save it. This is the only real option so I press save file. I get a box saying this is an executable file which may contain viruses - do you want to run. I press ok and the final box showing C drive file name and desktop appears stating application not found.
This happens the same whenever I try to install.
To my untrained eye the application is not being recognised as an application and I cannot work out how to get it to do that.
My plugin is still showing as out of date.
Is there anything you could suggest. Thanks for your time.

Satellite L300-15V - The system cannot install Wireless LAN driver

Similar Messages

Maybe you are looking for