Satellite L300-1BW - Error code 19 on CD/DVD drive

Allo Folks, My wife's Satellite L300-1BW has lost it's DVD drive - The Hardware Manager properties gives the following error:
'Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)'
I tried uninstalling the DVD driver, then rebooting to let it re-install, but it still comes back with the same fault :-(
Any ideas anyone? ?:|

Hi!
Try to remove the upper and lower filters as in this Microsoft Knowledge Base article suggested:
http://support.microsoft.com/kb/314060
1) Run Regedit (Start > Run > Regedit)
2) Navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class{4D36E965-E325-11CE-BFC1-08002BE10318}
3) In the right pane, delete the "UpperFilters" key, and delete the "LowerFilters" key.
4) Reboot.
Bye

Similar Messages

Satellite L300-1BW - Is very slow

Hi, everyone!
Recently, I bought TOSHIBA SATELLITE L300-1BW (PSLB8E)
Link: http://uk.computers.toshiba-europe.com/innovation/jsp/supportMyProduct.do?service=UK&userAction=SMP_RESU LTS_PAGE&partNumber=PSLB8E-03F007EN&serialNumber=Y8805872q&USER_ACTION=Serial %20number
I need this for my study and home using. Computer working VERY slowly. Now I have a Windows XP Pro SP3 64-bit version. Programs what I have only Ms Office, Skype, Nero, antivirus - BitDefender. I do not play any games. Application Im using for my study only - Ms Word.
My computer was checked in service center and no any faults were wound - no any sofware and hardware damages, viruses, no any manufacture faults. Owners of these model please give me advice what to do. I stucked!
Do I need to install Windows XP 32bit or install Windows 2000 or any hardware upgrade (memory ... whatever)? I don`t want be disappointed by TOSHIBA!
Ill appreciate any HELP!

Hi buddy,
Can you be a little bit more detailed, please? What do you understand with very slow?
How long it takes to startup Windows?
How long it takes to start an application?
I have to say that Windows XP 64bit wasnt popular and there is no official support from Toshiba for this OS. If you want to use Windows XP, I can recommend installing the 32bit version.
Have you tested your notebook with factory settings? Does it work properly with preinstalled OS from Toshiba?
Im also Satellite L300 owner and I use the preinstalled Windows XP 32bit from Toshiba. Im very satisfied with this notebook, its pretty fast and need few energy. :)

How can I switch the region code on MBP w/ DVD drive for the 5th and final time?

How can I switch the region code on MBP w/ DVD drive for the 5th and final time? It brings up the window with that world map to do it, including the warning that "this is the 5th and final time I can do this", when inserting a DVD and opening "DVD Player", but it never executes my click on the "Change Drive Region" button prompt.
VLC or Quicktime Player won't play it either, but won't bring up that window to change Region Code anyway....
Otherwise, I'm not having any other issues with this MBP at all. Peak performance on all counts :-)
I tried resetting SMC after chatting w/ Apple Support, but it didn't help.
That was the link they provided. Resetting the System Management Controller (SMC) on your Mac
Tried zapping PRAM as well.
Thanks for any clues, Rene

Region encoding is the mechanism that enables motion picture studios to control the worldwide release of their movies. It is required by the DVD Forum (http://www.dvdforum.org/forum.shtml) in all commercial hardware DVD players. Every DVD-Video disc contains one byte of data representing a region code, which limits where the disc can be played.
http://support.apple.com/kb/HT2397
Once you have set the region in DVD Player five times it cannot be changed. However see this also:
http://support.apple.com/kb/TA25416?viewlocale=en_US&locale=en_US
Instead, use VLC to view videos from different regions:
http://www.videolan.org/vlc/download-macosx.html

Satellite Pro L300-23L: error code 12 in device manager after Vista install

Ok,
So I've re-installed Vista (32 w/ SP2) on my Satellite L300-23L after a virus and I'm having a couple of issues:
Issue 1
A Code 12 on Intel Family Chipset 4 - There are two versions of this in the device manager, one is hidden. The one that isn't hidden is the one with the Code 12. I've tried installing latest drivers from both Toshiba and Intel. Problem still persists.
Issue 2
The sleep option on my power off section is greyed out and the hibernate option is missing altogether. Have tried upgrading BIOS but install says that they are up to date.
HELP! - I can find my way around a computer but don't assume I'll just know how to do something, I'd be grateful if you could walk me through any actions.
Thanks in advance. :)

Hi
The error code 12 means:
This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12)
Dont think this has something to do with the missing driver.
Would recommend doing this firstly:
1. Go to Start Menu-All Programs-Accessories, then right-click Command Prompt and select Run As Administrator
2. Enter: bcdedit /set CONFIGACCESSPOLICY DISALLOWMMCONFIG
3. Restart your PC

Satellite Pro 4330: Error code IDE #1 error

Hello
I got old satellite pro 4330 but I got the error code IDE #1 Error, what can I do? I need help please!
Thanx

Hi!
Yes, Markus77 is on the right track.
But, I would simply guess the CD-ROM drive is somehow out-of-order or broken, and that's why the Laptop has been available (hopefully not for sale for too many bucks ...)
One simple repair trial could be to open the Laptop and take the CD drive out of its bay and cable connector, clean them and place back carefully, and if lucky enough, it may wake-up for the BIOS, or maybe not ...
Best regards,
Pete V.

Satellite L300-1AS - error while creating a Recovery disc

I am trying to create recovery disc for Sat L300-1AS,
I have tried a number of various DVD discs from top quality to DVD-R / DVD+R but each time when the system is verifying the data I get an error message 02016F-3C 00000000
What am i doing wrong please help as frustration is really beginning to kick in now
Thanks

> have tried to update the driver,(T002 & T003) but the systems does not allow it
Seems the firmware has not been released for the CD/DVD drive installed in your notebook.
> only bought it yesterday think I may take it back to the retailer and get a replacement
Yes, maybe you should do this

CD/DVD drive issue on Satellite L notebook - error code Code 39

Hi,
Could anyone tell me if there is an updated driver for the TSSTcorp CDDVDW TS-L632H ATA Device? The device is not available as a selectable drive and in device manager it reports the following error:
Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)
I have removed the device and the driver, however on scanning for hardware; vista re-installs the default driver and the same error returns.
Because of this error, I am unable to update the firmware for the drive and the firmware update is unable to see the drive.
Any ideas??
Thanks in advance.

Hi buddy
What to saythis issue is known and caused by wrong Windows registry entries.
Microsoft has released and published some knowledge articles.
Check this:
http://support.microsoft.com/kb/270008/en-us
First of all I recommend removing the CD/DVD drive from the device list in device manager. Then remove the Upperfilters and Lowerfilters values completely from the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
Finally reboot the notebook.
Thats all.
PS: you would find this solution also without my help. You should use the forum search function! Its helpful!

DVD Drive not working Satellite Pro A100 - error Code 37

Hi
Anyone help on this?
I have an A-100 and the DVD drive has stopped working in XP. I've checked device manager and XP see's the drive but returns this error 'Windows cannot initialize the device driver for this hardware. (Code 37)'
I've also noticed that ASAPI.sys is not running in task manager.
I'm guessing this has got something to do with the problem.
I've tried reinstalling device drivers but this has made no difference. Any suggestions?

Hi
The error code 37 means the driver returned failure from its DriverEntry routine.
You could try to remove the driver from the device manager and after new reboot the OS should recognize the device drive and initialize the driver again.
If this does not help try this procedure:
Run REGEDIT and open up the following folders:
HKEY_LOCAL_MACHINE
-> SYSTEM
-> CurrentControlSet
-> Control
->Class
{4D36E965-E325 -11CE-BFC1-08002BE10318}
After clicking on {4D36E965-E325 -11CE-BFC1-08002BE10318} you should see two settings on the right-hand side:
"Upperfilters"
"Lowerfilters"
Click on each of them, press DELETE and click YES.
Then reboot the notebook and check if it was useful.

Error code -36 -- Is my hard drive about to fail?

Hello:
I am using SuperDuper to backup, and today, I got an error saying that backup failed because of an "input/output" error concerning an mp3 file.
Someone at SuperDuper suggested I try to duplicate that file using Finder and see what happened.
Sure enough, when I tried to duplicate the file using Finder, I got an "Error Code -36" message saying that the file cannot be read or written.
I then chose another file (also an mp3 within the same album) and it, too, failed. All others were OK.
But then, I went back and again tried to duplicate the original bad file, and this time I was successful.
Then, I deleted the one bad file, and tried to backup to my external hard drive using SuperDuper...and I was successful.
However, the person at Super Duper says my internal hard drive is about to fail.
Can that be true? On an 18-month old iMac?
I ran Disk Utility/Verify Disk, and it says the Hard Drive appears OK.
Any advice?
Thanks!

Run the free demo of SMART Utility to check your drive.
http://www.volitans-software.com/smart_utility.php
Drives can fail at any time, even new ones.
Message was edited by: WZZZ

Error Code -36 writing to external drives

Hello all,
I was working in Final Cut Pro with a project, and I updated to 10.5.7 (dumb, I know). The next time I tried to open my project, it returned the message "The project is unreadable, or may be too new for this version of Final Cut."
I restarted the computer,
trashed preferences from Username>Library>Preferences>com.apple.finalcutpro.plist,
attempted to open backup files of the project (stored on my Macintosh HD, when the working project files are stored on a different internal media drive),
connected my laptop (running 10.5.6) and moved the project file (and backups) to the laptop, and attempted to open with it,
attempted to connect external drives to move the project files, and try from the laptop that way and I started receiving two errors: "The Finder cannot complete the operation because some data in 'Test_movie.mov' could not be read or written. (Error code -36), or another error about file names being too long.
I booted to the OSX disk, and ran disk utility, repairing all internal drives, and repairing disk permissions for my OSX drive.
I tried firewire 400 & 800.
I formatted the external drives, and still received the message (actually, after formatting, the message changed from the "names too long" to the "Error Code -36" I listed above).
I don't know what else I can try. Older FCP projects as well as all types of documents and images seem to open just fine. Does anyone have any ideas?
Thanks,
Lawrence

I was getting the same "-36" error while trying to backup to a Lacie firewire external drive.
I had a lot of people telling me to re-format, erase, reinstall, run utility programs ... yada, yada, yada.
First off, test to see if it is the connection type (firewire). I reconnected the offending external drive via USB, restarted the drive and ... BINGO! ... all transfers went perfectly.
Once i knew it was the firewire connection and not the drive itself i simply unplugged my iSight camera (the only other firewire device connected to my machine), reconnected my external drive via firewire and the problem is now corrected.
Firewire buses seem to be very finicky things ... i would suggest eliminating all firewire devices from the machine (except, of course, the external drive you're trying to transfer to) and see if the problem goes away.
Like i said, i simply unplugged my iSight camera and the transfer to my external drive went perfect and my transfer rates went from an average of 4MB/sec to over 19MB/sec.
P.S. BTW - prior to the error and after i corrected the error by unplugging the iSight camera, my internal and external drives all checked out 100% on Disk Utility, Disk Warrior and TechTool Pro.

Error Code 0X8002006D while burning DVD's

I've had a problem with my SuperDrive burning DVD's. I succeeded in burning CD's a while ago, but DVD's now. The error message 0X8002006D is popping up. What's does the error code mean? Could the laserlens be dirty or...?

Read this thread. You might try a lens cleaner.
http://discussions.apple.com/thread.jspa?threadID=119512&tstart=0
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
 An Apple User Group 

Error Code Definition for JDBC Thin driver

Would like to know where I can find the definition of error codes
for JDBC thin driver to Oracle 7 database. Right now, when I have
database errors, I get SQL execption with CODE=XXXXXX. Need to
know the definition of the error codes in order to decide whether
the application shall retry or quit or do something else. Thank
you in advance.
null

Hi,
thin client session Language is controlled by java Locale.
Based on testing code, ORA- messages are localized after the connection is successfully established. ORA- messages returned in the middle of connecting are in instance language.
So, as far as I can say, you need to catch exceptions from DriverManager.getConnection(url, info); and translate them on your own.
Once the connection is successfully returned, ORA- message language is defined by java Locale.
Tests were performed on Oracle 10gR2 (both thin driver and DB).

Error code -43 when burning DVD

When I try to burn a DVD this pops up. Thanks to anyone that can help.
The operation cannot be completed because one or more required items cannot be found.
(Error code-43).
Could not open the data fork of "<unable to get file path>"(-43).

Please tell us what burner you have. Look in System
Profiler > Hardware > Disc Burning.
You're using the Finder to burn?
A Google search on this error code turns up a lot of
topics. Some point to the media as the culprit,
others point to Tiger, some to the drive itself.
Fuji isn't a bad brand of media, but it's not
amongst the best, either.
Generally, an older burner can use 16X media, but
would obviously only be able to burn at the maximum
speed of the drive. It's possible that your drive
doesn't recognize the media code on the disc and
refuses to burn. Sometimes a firmware update to the
drive can solve this problem.
Here's the info under System Profiler>Hardware>Disc Burning:
SONY DVD RW DW-U10A:
Firmware Revision: A43h
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 8192 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media: No
I'm trying to burn data onto a DVD disc as backup. How do I burn using Finder?
Also, Power Mac G5 Uniprocessor Firmware update 5.1.5f2 does show when I click on Apple>software updates. However, it does not have a check mark. Would this apply to my computer even though it does not have a check mark?

"error code-39 with core audio driver"

so I have a 75 minute continuous dj mix I recorded onto garageband... after having recorded this I then converted the file from a 120bpm to a 60bpm speed so as to fit it all in... now, however, towards the end (between 65-70 minutes into it) the mix suddenly is interuppted by a crude digital-type sound. a pop up then says "error code-39 with or in core audio driver"....
what gives here?
I'd appreciate any help you can give.
peace.

does this mean I have to re-record the audio file?
Probably. I guess you could try a commercial disc repair program like TechTool Pro or Disk Warrior, but odds are if the file system can't figure out where the end of file is, the file is hosed --Hang B-(>

How to access error description in a string from error code returned by NI-DAQ driver?

I am tring to write codes to control NI-6703 for PCI using the NI-DAQ driver for C++.
In the sample codes, it calls "NIDAQErrorHandler" to retrieve the error description and display in the pop-up message box. The method is included with header file "nideqex.h", and implemented w/ the nidex32.lib
I would like to get the error description in a string rather than getting a message box. Is there a way to do that? Am I missig something here?
I managed to find the "NIDAQEx.c" source code on the internet, but it seems like the code is outdated, and the library is NOT really compiled from it, since it does not seems to have a call to any method that will return th
e error description in a string that got used to be displayed in the message box.
Is there a method that I can call and pass a error code, which will return the error description in a string?

There is a function documented in dataacq.h called GetNIDAQErrorString that accomplishes what you would like.
Raecine Meza
NI
http://www.ni.com/ask

Satellite L300-1BW - Error code 19 on CD/DVD drive

Similar Messages

Maybe you are looking for